| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 327d5b2fee91c404a3956c324193892cf2cc9528 ]
The IOMMU driver calculates the guest addressability for a DMA request
based on the value of the mgaw reported from the IOMMU. However, this
is a fused value and as mentioned in the spec, the guest width
should be calculated based on the minimum of supported adjusted guest
address width (SAGAW) and MGAW.
This is from specification:
"Guest addressability for a given DMA request is limited to the
minimum of the value reported through this field and the adjusted
guest address width of the corresponding page-table structure.
(Adjusted guest address widths supported by hardware are reported
through the SAGAW field)."
This causes domain initialization to fail and following
errors appear for EHCI PCI driver:
[ 2.486393] ehci-pci 0000:01:00.4: EHCI Host Controller
[ 2.486624] ehci-pci 0000:01:00.4: new USB bus registered, assigned bus
number 1
[ 2.489127] ehci-pci 0000:01:00.4: DMAR: Allocating domain failed
[ 2.489350] ehci-pci 0000:01:00.4: DMAR: 32bit DMA uses non-identity
mapping
[ 2.489359] ehci-pci 0000:01:00.4: can't setup: -12
[ 2.489531] ehci-pci 0000:01:00.4: USB bus 1 deregistered
[ 2.490023] ehci-pci 0000:01:00.4: init 0000:01:00.4 fail, -12
[ 2.490358] ehci-pci: probe of 0000:01:00.4 failed with error -12
This issue happens when the value of the sagaw corresponds to a
48-bit agaw. This fix updates the calculation of the agaw based on
the minimum of IOMMU's sagaw value and MGAW.
This issue happens on the code path of getting a private domain for a
device. A private domain was needed when the domain of an iommu group
couldn't meet the requirement of a device. The IOMMU core has been
evolved to eliminate the need for private domain, hence this code path
has alreay been removed from the upstream since commit 327d5b2fee91c
("iommu/vt-d: Allow 32bit devices to uses DMA domain"). Instead of back
porting all patches that are required for removing the private domain,
this simply fixes it in the affected stable kernel between v4.16 and v5.7.
[baolu: The orignal patch could be found here
https://lore.kernel.org/linux-iommu/20210412202736.70765-1-saeed.mirzamohammadi@oracle.com/.
I added commit message according to Greg's comments at
https://lore.kernel.org/linux-iommu/YHZ%2FT9x7Xjf1r6fI@kroah.com/.]
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org #v4.16+
Signed-off-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Tested-by: Camille Lu <camille.lu@hpe.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 77e89afc25f30abd56e76a809ee2884d7c1b63ce upstream.
Multi-MSI uses a single MSI descriptor and there is a single mask register
when the device supports per vector masking. To avoid reading back the mask
register the value is cached in the MSI descriptor and updates are done by
clearing and setting bits in the cache and writing it to the device.
But nothing protects msi_desc::masked and the mask register from being
modified concurrently on two different CPUs for two different Linux
interrupts which belong to the same multi-MSI descriptor.
Add a lock to struct device and protect any operation on the mask and the
mask register with it.
This makes the update of msi_desc::masked unconditional, but there is no
place which requires a modification of the hardware register without
updating the masked cache.
msi_mask_irq() is now an empty wrapper which will be cleaned up in follow
up changes.
The problem goes way back to the initial support of multi-MSI, but picking
the commit which introduced the mask cache is a valid cut off point
(2.6.30).
Fixes: f2440d9acbe8 ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.726833414@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d28d4ad2a1aef27458b3383725bb179beb8d015c upstream.
No point in using the raw write function from shutdown. Preparatory change
to introduce proper serialization for the msi_desc::masked cache.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.674391354@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 689e6b5351573c38ccf92a0dd8b3e2c2241e4aff upstream.
The comments about preserving the cached state in pci_msi[x]_shutdown() are
misleading as the MSI descriptors are freed right after those functions
return. So there is nothing to restore. Preparatory change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.621609423@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 361fd37397f77578735907341579397d5bed0a2d upstream.
msi_mask_irq() takes a mask and a flags argument. The mask argument is used
to mask out bits from the cached mask and the flags argument to set bits.
Some places invoke it with a flags argument which sets bits which are not
used by the device, i.e. when the device supports up to 8 vectors a full
unmask in some places sets the mask to 0xFFFFFF00. While devices probably
do not care, it's still bad practice.
Fixes: 7ba1930db02f ("PCI MSI: Unmask MSI if setup failed")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.568173099@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9255a7cb51754e8d2645b65dd31805e282b4f3e upstream.
Nothing enforces the posted writes to be visible when the function
returns. Flush them even if the flush might be redundant when the entry is
masked already as the unmask will flush as well. This is either setup or a
rare affinity change event so the extra flush is not the end of the world.
While this is more a theoretical issue especially the logic in the X86
specific msi_set_affinity() function relies on the assumption that the
update has reached the hardware when the function returns.
Again, as this never has been enforced the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.515188147@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da181dc974ad667579baece33c2c8d2d1e4558d5 upstream.
The specification (PCIe r5.0, sec 6.1.4.5) states:
For MSI-X, a function is permitted to cache Address and Data values
from unmasked MSI-X Table entries. However, anytime software unmasks a
currently masked MSI-X Table entry either by clearing its Mask bit or
by clearing the Function Mask bit, the function must update any Address
or Data values that it cached from that entry. If software changes the
Address or Data value of an entry while the entry is unmasked, the
result is undefined.
The Linux kernel's MSI-X support never enforced that the entry is masked
before the entry is modified hence the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Enforce the entry to be masked across the update.
There is no point in enforcing this to be handled at all possible call
sites as this is just pointless code duplication and the common update
function is the obvious place to enforce this.
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Reported-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.462096385@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d5ec3d3612396dc6d4b76366d20ab9fc06f399f upstream.
When MSI-X is enabled the ordering of calls is:
msix_map_region();
msix_setup_entries();
pci_msi_setup_msi_irqs();
msix_program_entries();
This has a few interesting issues:
1) msix_setup_entries() allocates the MSI descriptors and initializes them
except for the msi_desc:masked member which is left zero initialized.
2) pci_msi_setup_msi_irqs() allocates the interrupt descriptors and sets
up the MSI interrupts which ends up in pci_write_msi_msg() unless the
interrupt chip provides its own irq_write_msi_msg() function.
3) msix_program_entries() does not do what the name suggests. It solely
updates the entries array (if not NULL) and initializes the masked
member for each MSI descriptor by reading the hardware state and then
masks the entry.
Obviously this has some issues:
1) The uninitialized masked member of msi_desc prevents the enforcement
of masking the entry in pci_write_msi_msg() depending on the cached
masked bit. Aside of that half initialized data is a NONO in general
2) msix_program_entries() only ensures that the actually allocated entries
are masked. This is wrong as experimentation with crash testing and
crash kernel kexec has shown.
This limited testing unearthed that when the production kernel had more
entries in use and unmasked when it crashed and the crash kernel
allocated a smaller amount of entries, then a full scan of all entries
found unmasked entries which were in use in the production kernel.
This is obviously a device or emulation issue as the device reset
should mask all MSI-X table entries, but obviously that's just part
of the paper specification.
Cure this by:
1) Masking all table entries in hardware
2) Initializing msi_desc::masked in msix_setup_entries()
3) Removing the mask dance in msix_program_entries()
4) Renaming msix_program_entries() to msix_update_entries() to
reflect the purpose of that function.
As the masking of unused entries has never been done the Fixes tag refers
to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.403833459@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 438553958ba19296663c6d6583d208dfb6792830 upstream.
The ordering of MSI-X enable in hardware is dysfunctional:
1) MSI-X is disabled in the control register
2) Various setup functions
3) pci_msi_setup_msi_irqs() is invoked which ends up accessing
the MSI-X table entries
4) MSI-X is enabled and masked in the control register with the
comment that enabling is required for some hardware to access
the MSI-X table
Step #4 obviously contradicts #3. The history of this is an issue with the
NIU hardware. When #4 was introduced the table access actually happened in
msix_program_entries() which was invoked after enabling and masking MSI-X.
This was changed in commit d71d6432e105 ("PCI/MSI: Kill redundant call of
irq_set_msi_desc() for MSI-X interrupts") which removed the table write
from msix_program_entries().
Interestingly enough nobody noticed and either NIU still works or it did
not get any testing with a kernel 3.19 or later.
Nevertheless this is inconsistent and there is no reason why MSI-X can't be
enabled and masked in the control register early on, i.e. move step #4
above to step #1. This preserves the NIU workaround and has no side effects
on other hardware.
Fixes: d71d6432e105 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cddce01160582a5f52ada3da9626c052d852ec42 ]
There is a race between iterating over requests in
nbd_clear_que() and completing requests in recv_work(),
which can lead to double completion of a request.
To fix it, flush the recv worker before iterating over
the requests and don't abort the completed request
while iterating.
Fixes: 96d97e17828f ("nbd: clear_sock on netlink disconnect")
Reported-by: Jiang Yadong <jiangyadong@bytedance.com>
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20210813151330.96-1-xieyongji@bytedance.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 88ca2521bd5b4e8b83743c01a2d4cb09325b51e9 ]
There is a TOCTOU issue in set_evtchn_to_irq. Rows in the evtchn_to_irq
mapping are lazily allocated in this function. The check whether the row
is already present and the row initialization is not synchronized. Two
threads can at the same time allocate a new row for evtchn_to_irq and
add the irq mapping to the their newly allocated row. One thread will
overwrite what the other has set for evtchn_to_irq[row] and therefore
the irq mapping is lost. This will trigger a BUG_ON later in
bind_evtchn_to_cpu:
INFO: pci 0000:1a:15.4: [1d0f:8061] type 00 class 0x010802
INFO: nvme 0000:1a:12.1: enabling device (0000 -> 0002)
INFO: nvme nvme77: 1/0/0 default/read/poll queues
CRIT: kernel BUG at drivers/xen/events/events_base.c:427!
WARN: invalid opcode: 0000 [#1] SMP NOPTI
WARN: Workqueue: nvme-reset-wq nvme_reset_work [nvme]
WARN: RIP: e030:bind_evtchn_to_cpu+0xc2/0xd0
WARN: Call Trace:
WARN: set_affinity_irq+0x121/0x150
WARN: irq_do_set_affinity+0x37/0xe0
WARN: irq_setup_affinity+0xf6/0x170
WARN: irq_startup+0x64/0xe0
WARN: __setup_irq+0x69e/0x740
WARN: ? request_threaded_irq+0xad/0x160
WARN: request_threaded_irq+0xf5/0x160
WARN: ? nvme_timeout+0x2f0/0x2f0 [nvme]
WARN: pci_request_irq+0xa9/0xf0
WARN: ? pci_alloc_irq_vectors_affinity+0xbb/0x130
WARN: queue_request_irq+0x4c/0x70 [nvme]
WARN: nvme_reset_work+0x82d/0x1550 [nvme]
WARN: ? check_preempt_wakeup+0x14f/0x230
WARN: ? check_preempt_curr+0x29/0x80
WARN: ? nvme_irq_check+0x30/0x30 [nvme]
WARN: process_one_work+0x18e/0x3c0
WARN: worker_thread+0x30/0x3a0
WARN: ? process_one_work+0x3c0/0x3c0
WARN: kthread+0x113/0x130
WARN: ? kthread_park+0x90/0x90
WARN: ret_from_fork+0x3a/0x50
This patch sets evtchn_to_irq rows via a cmpxchg operation so that they
will be set only once. The row is now cleared before writing it to
evtchn_to_irq in order to not create a race once the row is visible for
other threads.
While at it, do not require the page to be zeroed, because it will be
overwritten with -1's in clear_evtchn_to_irq_row anyway.
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Fixes: d0b075ffeede ("xen/events: Refactor evtchn_to_irq array to be dynamically allocated")
Link: https://lore.kernel.org/r/20210812130930.127134-1-mheyne@amazon.de
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 21b52fed928e96d2f75d2f6aa9eac7a4b0b55d22 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 871a73a1c8f55da0a3db234e9dd816ea4fd546f2 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 58c59ef9e930 ("net: dsa: lantiq: Add Forwarding Database access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ada2fee185d8145afb89056558bb59545b9dbdd0 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: ab335349b852 ("net: dsa: lan9303: Add port_fast_age and port_fdb_dump methods")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c34f674c8875235725c3ef86147a627f165d23b4 ]
ksz_read64() currently does some dubious byte-swapping on the two
halves of a 64-bit register, and then only returns the high bits.
Replace this with a straightforward expression.
Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf33677a3c394bb8fddd48d3bbc97adf0262e045 ]
Add support for the OSD1 HDR registers so meson DRM can handle the HDR
properties set by Amlogic u-boot on G12A and newer devices which result
in blue/green/pink colour distortion to display output.
This takes the original patch submissions from Mathias [0] and [1] with
corrections for formatting and the missing description and attribution
needed for merge.
[0] https://lore.kernel.org/linux-amlogic/59dfd7e6-fc91-3d61-04c4-94e078a3188c@baylibre.com/T/
[1] https://lore.kernel.org/linux-amlogic/CAOKfEHBx_fboUqkENEMd-OC-NSrf46nto+vDLgvgttzPe99kXg@mail.gmail.com/T/#u
Fixes: 728883948b0d ("drm/meson: Add G12A Support for VIU setup")
Suggested-by: Mathias Steiger <mathias.steiger@googlemail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Philip Milev <milev.philip@gmail.com>
[narmsrong: adding missing space on second tested-by tag]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210806094005.7136-1-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd37c2888ccaa5ceb9895718f6909b247cc372e0 ]
Check return value of mlx5_fw_tracer_start(), set error path and fix
return value of mlx5_fw_tracer_init() accordingly.
Fixes: c71ad41ccb0c ("net/mlx5: FW tracer, events handling")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a7550f8b1c9712894f9e98d6caf5f49451ebd058 ]
iavf driver should set RSS LUT and key unconditionally in reset
path. Currently, the driver does not do that. This patch fixes
this issue.
Fixes: 2c86ac3c7079 ("i40evf: create a generic config RSS function")
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2459dcb96bcba94c08d6861f8a050185ff301672 ]
IFLA_IFNAME is nul-term string which means that IFLA_IFNAME buffer can be
larger than length of string which contains.
Function __rtnl_newlink() generates new own ifname if either IFLA_IFNAME
was not specified at all or userspace passed empty nul-term string.
It is expected that if userspace does not specify ifname for new ppp netdev
then kernel generates one in format "ppp<id>" where id matches to the ppp
unit id which can be later obtained by PPPIOCGUNIT ioctl.
And it works in this way if IFLA_IFNAME is not specified at all. But it
does not work when IFLA_IFNAME is specified with empty string.
So fix this logic also for empty IFLA_IFNAME in ppp_nl_newlink() function
and correctly generates ifname based on ppp unit identifier if userspace
did not provided preferred ifname.
Without this patch when IFLA_IFNAME was specified with empty string then
kernel created a new ppp interface in format "ppp<id>" but id did not
match ppp unit id returned by PPPIOCGUNIT ioctl. In this case id was some
number generated by __rtnl_newlink() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: bb8082f69138 ("ppp: build ifname using unit identifier for rtnl based devices")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2383cb9497d113360137a2be308b390faa80632d ]
Commit a5e63c7d38d5 "net: phy: micrel: Fix detection of ksz87xx
switch" broke link detection on the external ports of the KSZ8795.
The previously unused phy_driver structure for these devices specifies
config_aneg and read_status functions that appear to be designed for a
fixed link and do not work with the embedded PHYs in the KSZ8795.
Delete the use of these functions in favour of the generic PHY
implementations which were used previously.
Fixes: a5e63c7d38d5 ("net: phy: micrel: Fix detection of ksz87xx switch")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
gpio-lookup tables
[ Upstream commit 9d7b132e62e41b7d49bf157aeaf9147c27492e0f ]
The gpiod_lookup_table.table passed to gpiod_add_lookup_table() must
be terminated with an empty entry, add this.
Note we have likely been getting away with this not being present because
the GPIO lookup code first matches on the dev_id, causing most lookups to
skip checking the table and the lookups which do check the table will
find a matching entry before reaching the end. With that said, terminating
these tables properly still is obviously the correct thing to do.
Fixes: f8eb0235f659 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210806115515.12184-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f560cd502190a9fd0ca8db0a15c5cca7d9091d2c ]
This reverts commit 5037d4ddda31c2dbbb018109655f61054b1756dc.
Explanation why this does not work:
This change connects the simswap to the LED subsystem of the kernel.
From my point of view, it's nonsense. If we do it this way, then this
can be switched relatively easily via the LED subsystem (trigger:
none/default-on) and that is dangerous! If this is used, it would be
unfavorable, since there is also another trigger (trigger:
heartbeat/netdev).
Therefore, this simswap GPIO should remain in the GPIO
subsystem and be switched via it and not be connected to the LED
subsystem. To avoid the problems mentioned above. The LED subsystem is
not made for this and it is not a good compromise, but rather dangerous.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aff51c5da3208bd164381e1488998667269c6cf4 ]
Add the missing RxUnicast counter.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 889d0e7dc68314a273627d89cbb60c09e1cc1c25 ]
Both MAC802154_HWSIM_ATTR_RADIO_ID and MAC802154_HWSIM_ATTR_RADIO_EDGE
must be present to fix GPF.
Fixes: f25da51fdc38 ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210707155633.1486603-1-mudongliangabcd@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9faf53c5a5d01f6f2a09ae28ec63a3bbd6f64fd ]
Both MAC802154_HWSIM_ATTR_RADIO_ID and MAC802154_HWSIM_ATTR_RADIO_EDGE,
MAC802154_HWSIM_EDGE_ATTR_ENDPOINT_ID and MAC802154_HWSIM_EDGE_ATTR_LQI
must be present to fix GPF.
Fixes: f25da51fdc38 ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210705131321.217111-1-mudongliangabcd@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d9cee9f85b22fab88d2b76d2e92b18e3d0e6aa8c upstream.
There are a few scenarios where init_active_labels() can return without
registering deactivate_labels() to run when the region is disabled. In
particular label error injection creates scenarios where a DIMM is
disabled, but labels on other DIMMs in the region become activated.
Arrange for init_active_labels() to always register deactivate_labels().
Reported-by: Krzysztof Kensicki <krzysztof.kensicki@intel.com>
Cc: <stable@vger.kernel.org>
Fixes: bf9bccc14c05 ("libnvdimm: pmem label sets and namespace instantiation.")
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/162766356450.3223041.1183118139023841447.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b93dfa6bda4d4e88e5386490f2b277a26958f9d3 upstream.
Fix the NFIT parsing code to treat a 0 index in a SPA Range Structure as
a special case and not match Region Mapping Structures that use 0 to
indicate that they are not mapped. Without this fix some platform BIOS
descriptions of "virtual disk" ranges do not result in the pmem driver
attaching to the range.
Details:
In addition to typical persistent memory ranges, the ACPI NFIT may also
convey "virtual" ranges. These ranges are indicated by a UUID in the SPA
Range Structure of UUID_VOLATILE_VIRTUAL_DISK, UUID_VOLATILE_VIRTUAL_CD,
UUID_PERSISTENT_VIRTUAL_DISK, or UUID_PERSISTENT_VIRTUAL_CD. The
critical difference between virtual ranges and UUID_PERSISTENT_MEMORY,
is that virtual do not support associations with Region Mapping
Structures. For this reason the "index" value of virtual SPA Range
Structures is allowed to be 0. If a platform BIOS decides to represent
NVDIMMs with disconnected "Region Mapping Structures" (range-index ==
0), the kernel may falsely associate them with standalone ranges where
the "SPA Range Structure Index" is also zero. When this happens the
driver may falsely require labels where "virtual disks" are expected to
be label-less. I.e. "label-less" is where the namespace-range ==
region-range and the pmem driver attaches with no user action to create
a namespace.
Cc: Jacek Zloch <jacek.zloch@intel.com>
Cc: Lukasz Sobieraj <lukasz.sobieraj@intel.com>
Cc: "Lee, Chun-Yi" <jlee@suse.com>
Cc: <stable@vger.kernel.org>
Fixes: c2f32acdf848 ("acpi, nfit: treat virtual ramdisk SPA as pmem region")
Reported-by: Krzysztof Rusocki <krzysztof.rusocki@intel.com>
Reported-by: Damian Bassa <damian.bassa@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/162870796589.2521182.1240403310175570220.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 86ff25ed6cd8240d18df58930bd8848b19fce308 upstream.
If an i2c driver happens to not provide the full amount of data that a
user asks for, it is possible that some uninitialized data could be sent
to userspace. While all in-kernel drivers look to be safe, just be sure
by initializing the buffer to zero before it is passed to the i2c driver
so that any future drivers will not have this issue.
Also properly copy the amount of data recvieved to the userspace buffer,
as pointed out by Dan Carpenter.
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5afc1540f13804a31bb704b763308e17688369c5 upstream.
Currently the for-loop that scans for the optimial adc_period iterates
through all the possible adc_period levels because the exit logic in
the loop is inverted. I believe the comparison should be swapped and
the continue replaced with a break to exit the loop at the correct
point.
Addresses-Coverity: ("Continue has no effect")
Fixes: e08e19c331fb ("iio:adc: add iio driver for Palmas (twl6035/7) gpadc")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210730071651.17394-1-colin.king@canonical.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84edec86f449adea9ee0b4912a79ab8d9d65abb7 upstream.
The datasheets have the following note for the conversion time
specification: "This parameter is specified by design and/or
characterization and it is not tested in production."
Parts have been seen that require more time to do 14-bit conversions for
the relative humidity channel. The result is ENXIO due to the address
phase of a transfer not getting an ACK.
Delay an additional 1 ms per conversion to allow for additional margin.
Fixes: 4839367d99e3 ("iio: humidity: add HDC100x support")
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Link: https://lore.kernel.org/r/20210614141820.2034827-1-chris.lesiak@licor.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9898cb24e454602beb6e17bacf9f97b26c85c955 upstream.
The ADS7950 requires that CS is deasserted after each SPI word. Before
commit e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") the driver used a message with one spi transfer per channel
where each but the last one had .cs_change set to enforce a CS toggle.
This was wrongly translated into a message with a single transfer and
.cs_change set which results in a CS toggle after each word but the
last which corrupts the first adc conversion of all readouts after the
first readout.
Fixes: e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210709101110.1814294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0d62baa7f505bd4c59cd169692ff07ec49dde37 upstream.
Printing kernel pointers is discouraged because they might leak kernel
memory layout. This fixes smatch warning:
drivers/net/ethernet/xilinx/xilinx_emaclite.c:1191 xemaclite_of_probe() warn:
argument 4 to %08lX specifier is cast from pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3125f26c514826077f2a4490b75e9b1c7a644c42 upstream.
When registering new ppp interface via PPPIOCNEWUNIT ioctl then kernel has
to choose interface name as this ioctl API does not support specifying it.
Kernel in this case register new interface with name "ppp<id>" where <id>
is the ppp unit id, which can be obtained via PPPIOCGUNIT ioctl. This
applies also in the case when registering new ppp interface via rtnl
without supplying IFLA_IFNAME.
PPPIOCNEWUNIT ioctl allows to specify own ppp unit id which will kernel
assign to ppp interface, in case this ppp id is not already used by other
ppp interface.
In case user does not specify ppp unit id then kernel choose the first free
ppp unit id. This applies also for case when creating ppp interface via
rtnl method as it does not provide a way for specifying own ppp unit id.
If some network interface (does not have to be ppp) has name "ppp<id>"
with this first free ppp id then PPPIOCNEWUNIT ioctl or rtnl call fails.
And registering new ppp interface is not possible anymore, until interface
which holds conflicting name is renamed. Or when using rtnl method with
custom interface name in IFLA_IFNAME.
As list of allocated / used ppp unit ids is not possible to retrieve from
kernel to userspace, userspace has no idea what happens nor which interface
is doing this conflict.
So change the algorithm how ppp unit id is generated. And choose the first
number which is not neither used as ppp unit id nor in some network
interface with pattern "ppp<id>".
This issue can be simply reproduced by following pppd call when there is no
ppp interface registered and also no interface with name pattern "ppp<id>":
pppd ifname ppp1 +ipv6 noip noauth nolock local nodetach pty "pppd +ipv6 noip noauth nolock local nodetach notty"
Or by creating the one ppp interface (which gets assigned ppp unit id 0),
renaming it to "ppp1" and then trying to create a new ppp interface (which
will always fails as next free ppp unit id is 1, but network interface with
name "ppp1" exists).
This patch fixes above described issue by generating new and new ppp unit
id until some non-conflicting id with network interfaces is generated.
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26b75952ca0b8b4b3050adb9582c8e2f44d49687 upstream.
Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.
When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.
Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cb10f68ad8150f243964b19391711aaac5e8ff42 ]
If the device is already in the runtime suspended state, any call to
the pullup routine will issue a runtime resume on the DWC3 core
device. If the USB gadget is disabling the pullup, then avoid having
to issue a runtime resume, as DWC3 gadget has already been
halted/stopped.
This fixes an issue where the following condition occurs:
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
-->pm_runtime_get_sync() -> ret = 0
-->pm_runtime_put() [async]
-->usb_gadget_udc_stop()
-->dwc3_gadget_stop()
-->dwc->gadget_driver = NULL
...
dwc3_suspend_common()
-->dwc3_gadget_suspend()
-->DWC3 halt/stop routine skipped, driver_data == NULL
This leads to a situation where the DWC3 gadget is not properly
stopped, as the runtime resume would have re-enabled EP0 and event
interrupts, and since we avoided the DWC3 gadget suspend, these
resources were never disabled.
Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1628058245-30692-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8212937305f84ef73ea81036dafb80c557583d4b ]
Current sequence utilizes dwc3_gadget_disable_irq() alongside
synchronize_irq() to ensure that no further DWC3 events are generated.
However, the dwc3_gadget_disable_irq() API only disables device
specific events. Endpoint events can still be generated. Briefly
disable the interrupt line, so that the cleanup code can run to
prevent device and endpoint events. (i.e. __dwc3_gadget_stop() and
dwc3_stop_active_transfers() respectively)
Without doing so, it can lead to both the interrupt handler and the
pullup disable routine both writing to the GEVNTCOUNT register, which
will cause an incorrect count being read from future interrupts.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1621571037-1424-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5aef629704ad4d983ecf5c8a25840f16e45b6d59 ]
Ensure that dep->flags are cleared until after stop active transfers
is completed. Otherwise, the ENDXFER command will not be executed
during ep disable.
Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616610664-16495-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f09ddcfcb8c569675066337adac2ac205113471f ]
In the situations where the DWC3 gadget stops active transfers, once
calling the dwc3_gadget_giveback(), there is a chance where a function
driver can queue a new USB request in between the time where the dwc3
lock has been released and re-aquired. This occurs after we've already
issued an ENDXFER command. When the stop active transfers continues
to remove USB requests from all dep lists, the newly added request will
also be removed, while controller still has an active TRB for it.
This can lead to the controller accessing an unmapped memory address.
Fix this by ensuring parameters to prevent EP queuing are set before
calling the stop active transfers API.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1615507142-23097-1-git-send-email-wcheng@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a1383b3537a7bea1c213baa7878ccc4ecf4413b5 ]
usb_gadget_deactivate/usb_gadget_activate does not execute the UDC start
operation, which may leave EP0 disabled and event IRQs disabled when
re-activating the function. Move the enabling/disabling of USB EP0 and
device event IRQs to be performed in the pullup routine.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Tested-by: Michael Tretter <m.tretter@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reported-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609282837-21666-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 77adb8bdf4227257e26b7ff67272678e66a0b250 ]
The DWC3 runtime suspend routine checks for the USB connected parameter to
determine if the controller can enter into a low power state. The
connected state is only set to false after receiving a disconnect event.
However, in the case of a device initiated disconnect (i.e. UDC unbind),
the controller is halted and a disconnect event is never generated. Set
the connected flag to false if issuing a device initiated disconnect to
allow the controller to be suspended.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609283136-22140-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ae7e86108b12351028fa7e8796a59f9b2d9e1774 ]
In the DWC3 databook, for a device initiated disconnect or bus reset, the
driver is required to send dependxfer commands for any pending transfers.
In addition, before the controller can move to the halted state, the SW
needs to acknowledge any pending events. If the controller is not halted
properly, there is a chance the controller will continue accessing stale or
freed TRBs and buffers.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 566463afdbc43c7744c5a1b89250fc808df03833 upstream.
If poll() is called on a m2m device with the EPOLLOUT event after the
last buffer of the CAPTURE queue is dequeued, any buffer available on
OUTPUT queue will never be signaled because v4l2_m2m_poll_for_data()
starts by checking whether dst_q->last_buffer_dequeued is set and
returns EPOLLIN in this case, without looking at the state of the OUTPUT
queue.
Fix this by not early returning so we keep checking the state of the
OUTPUT queue afterwards.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 376e4199e327a5cf29b8ec8fb0f64f3d8b429819 ]
Currently TEE_SHM_DMA_BUF flag has been inappropriately used to not
register shared memory allocated for private usage by underlying TEE
driver: OP-TEE in this case. So rather add a new flag as TEE_SHM_PRIV
that can be utilized by underlying TEE drivers for private allocation
and usage of shared memory.
With this corrected, allow tee_shm_alloc_kernel_buf() to allocate a
shared memory region without the backing of dma-buf.
Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Co-developed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
ql_adapter_reset
[ Upstream commit 92766c4628ea349c8ddab0cd7bd0488f36e5c4ce ]
When calling the 'ql_wait_for_drvr_lock' and 'ql_adapter_reset', the driver
has already acquired the spin lock, so the driver should not call 'ssleep'
in atomic context.
This bug can be fixed by using 'mdelay' instead of 'ssleep'.
Reported-by: Letu Ren <fantasquex@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 17109e9783799be2a063b2bd861a508194b0a487 ]
When connecting without first doing a scan, the BSS list is empty
and __cfg80211_connect_result() generates this warning:
$ iw dev wlan0 connect -w VirtWifi
[ 15.371989] ------------[ cut here ]------------
[ 15.372179] WARNING: CPU: 0 PID: 92 at net/wireless/sme.c:756 __cfg80211_connect_result+0x402/0x440
[ 15.372383] CPU: 0 PID: 92 Comm: kworker/u2:2 Not tainted 5.13.0-kvm #444
[ 15.372512] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-3.fc34 04/01/2014
[ 15.372597] Workqueue: cfg80211 cfg80211_event_work
[ 15.372756] RIP: 0010:__cfg80211_connect_result+0x402/0x440
[ 15.372818] Code: 48 2b 04 25 28 00 00 00 75 59 48 8b 3b 48 8b 76 10 48 8d 65 e0 5b 41 5c 41 5d 41 5e 5d 49 8d 65 f0 41 5d e9 d0 d4 fd ff 0f 0b <0f> 0b e9 f6 fd ff ff e8 f2 4a b4 ff e9 ec fd ff ff 0f 0b e9 19 fd
[ 15.372966] RSP: 0018:ffffc900005cbdc0 EFLAGS: 00010246
[ 15.373022] RAX: 0000000000000000 RBX: ffff8880028e2400 RCX: ffff8880028e2472
[ 15.373088] RDX: 0000000000000002 RSI: 00000000fffffe01 RDI: ffffffff815335ba
[ 15.373149] RBP: ffffc900005cbe00 R08: 0000000000000008 R09: ffff888002bdf8b8
[ 15.373209] R10: ffff88803ec208f0 R11: ffffffffffffe9ae R12: ffff88801d687d98
[ 15.373280] R13: ffff88801b5fe000 R14: ffffc900005cbdc0 R15: dead000000000100
[ 15.373330] FS: 0000000000000000(0000) GS:ffff88803ec00000(0000) knlGS:0000000000000000
[ 15.373382] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 15.373425] CR2: 000056421c468958 CR3: 000000001b458001 CR4: 0000000000170eb0
[ 15.373478] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 15.373529] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 15.373580] Call Trace:
[ 15.373611] ? cfg80211_process_wdev_events+0x10e/0x170
[ 15.373743] cfg80211_process_wdev_events+0x10e/0x170
[ 15.373783] cfg80211_process_rdev_events+0x21/0x40
[ 15.373846] cfg80211_event_work+0x20/0x30
[ 15.373892] process_one_work+0x1e9/0x340
[ 15.373956] worker_thread+0x4b/0x3f0
[ 15.374017] ? process_one_work+0x340/0x340
[ 15.374053] kthread+0x11f/0x140
[ 15.374089] ? set_kthread_struct+0x30/0x30
[ 15.374153] ret_from_fork+0x1f/0x30
[ 15.374187] ---[ end trace 321ef0cb7e9c0be1 ]---
wlan0 (phy #0): connected to 00:00:00:00:00:00
Add the fake bss just before the connect so that cfg80211_get_bss()
finds the virtual network.
As some code was duplicated, move it in a common function.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Link: https://lore.kernel.org/r/20210706154423.11065-1-mcroce@linux.microsoft.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ecef6a9effe49e8e2635c839020b9833b71e934c ]
Data transfers are not required to be block aligned in memory, so they
span two pages. Fix this by splitting the call to >sff_data_xfer into
two for that case.
This has been broken since the initial libata import before the damn
of git, but was uncovered by the legacy ide driver removal.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210709130237.3730959-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a8eee86317f11e97990d755d4615c1c0db203d08 upstream.
Sparse reports a compile time warning when dereferencing an
__iomem pointer:
drivers/soc/ixp4xx/ixp4xx-qmgr.c:149:37: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:153:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:154:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:38: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:44: warning: dereference of noderef expression
Use __raw_readl() here for consistency with the rest of the file.
This should really get converted to some proper accessor, as the
__raw functions are not meant to be used in drivers, but the driver
has used these since the start, so for the moment, let's only fix
the warning.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: d4c9e9fc9751 ("IXP42x: Add QMgr support for IXP425 rev. A0 processors.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8311ee2164c5cd1b63a601ea366f540eae89f10e upstream.
In meson_spicc_probe, the error handling code needs to clean up master
by calling spi_master_put, but the remove function does not have this
function call. This will lead to memory leak of spicc->master.
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: 454fa271bc4e("spi: Add Meson SPICC driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210720100116.1438974-1-mudongliangabcd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8861452b2097bb0b5d0081a1c137fb3870b0a31f upstream.
When compile-testing with 64-bit resource_size_t, gcc reports an invalid
printk format string:
In file included from include/linux/dma-mapping.h:7,
from drivers/soc/ixp4xx/ixp4xx-npe.c:15:
drivers/soc/ixp4xx/ixp4xx-npe.c: In function 'ixp4xx_npe_probe':
drivers/soc/ixp4xx/ixp4xx-npe.c:694:18: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
dev_info(dev, "NPE%d at 0x%08x-0x%08x not available\n",
Use the special %pR format string to print the resources.
Fixes: 0b458d7b10f8 ("soc: ixp4xx: npe: Pass addresses as resources")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ba03936c05584b6f6f79be5ebe7e5036c1dd252 upstream.
Similar to [1], this patch fixes the same bug in raid10. Also cleanup the
comments.
[1] commit 2417b9869b81 ("md/raid1: properly indicate failure when ending
a failed write request")
Cc: stable@vger.kernel.org
Fixes: 7cee6d4e6035 ("md/raid10: end bio when the device faulty")
Signed-off-by: Wei Shuyu <wsy@dogben.com>
Acked-by: Guoqing Jiang <jiangguoqing@kylinos.cn>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
