| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Not much going on in the core for SPI this time but a reasonable
amount of change in the drivers:
- Removal of dmal_request_slave_channel() from Peter Ujfalusi.
- More conversions of drivers to GPIO descriptors from Linus Walleij.
- A big rework of the sh-msiof driver from Geert Uytterhoeven moving
it over to the generic native chipselect support.
- DMA support for the uniphier driver from Kunihiko Hayashi.
- New driver support for HiSilcon v3xx SPI NOR controllers from John
Garry"
* tag 'spi-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (52 commits)
dt-binding: spi: add NPCM PSPI reset binding
spi: pxa2xx: Avoid touching SSCR0_SSE on MMP2
spi: spi-fsl-qspi: Ensure width is respected in spi-mem operations
spi: npcm-pspi: modify reset support
spi: npcm-pspi: improve spi transfer performance
spi: spi-ti-qspi: fix warning
spi: npcm-pspi: fix 16 bit send and receive support
spi: pxa2xx: Add support for Intel Comet Lake PCH-V
spi: fsl: simplify error path in of_fsl_spi_probe()
spi: fsl-lpspi: fix only one cs-gpio working
spi: spi-ti-qspi: optimize byte-transfers
spi: spi-ti-qspi: support large flash devices
spi: spi-qcom-qspi: Use device managed memory for clk_bulk_data
MAINTAINERS: Add a maintainer for the HiSilicon v3xx SFC driver
spi: Add HiSilicon v3xx SPI NOR flash controller driver
dt-bindings: spi_atmel: add microchip,sam9x60-spi
spi: bcm2835: Raise maximum number of slaves to 4
spi: sh-msiof: Do not redefine STR while compile testing
spi: rspi: Add support for GPIO chip selects
spi: rspi: Add support for multiple native chip selects
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This is quite a busy release for a subsystem that's usually very
quiet, though still a small set of updates in the grand scheme of
things:
- A fix for writes to non-incrementing registers.
- An iopoll() style helper for use with atomic safe regmaps, making
it easier to transition from raw memory mapped I/O.
- Some constification"
* tag 'regmap-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix writes to non incrementing registers
regmap: add iopoll-like atomic polling macro
regmap-i2c: constify regmap_bus structures
|
|
Pull dmaengine updates from Vinod Koul:
"This time we have a bunch of core changes to support dynamic channels,
hotplug of controllers, new apis for metadata ops etc along with new
drivers for Intel data accelerators, TI K3 UDMA, PLX DMA engine and
hisilicon Kunpeng DMA engine. Also usual assorted updates to drivers.
Core:
- Support for dynamic channels
- Removal of various slave wrappers
- Make few slave request APIs as private to dmaengine
- Symlinks between channels and slaves
- Support for hotplug of controllers
- Support for metadata_ops for dma_async_tx_descriptor
- Reporting DMA cached data amount
- Virtual dma channel locking updates
New drivers/device/feature support support:
- Driver for Intel data accelerators
- Driver for TI K3 UDMA
- Driver for PLX DMA engine
- Driver for hisilicon Kunpeng DMA engine
- Support for eDMA support for QorIQ LS1028A in fsl edma driver
- Support for cyclic dma in sun4i driver
- Support for X1830 in JZ4780 driver"
* tag 'dmaengine-5.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (62 commits)
dmaengine: Create symlinks between DMA channels and slaves
dmaengine: hisilicon: Add Kunpeng DMA engine support
dmaengine: idxd: add char driver to expose submission portal to userland
dmaengine: idxd: connect idxd to dmaengine subsystem
dmaengine: idxd: add descriptor manipulation routines
dmaengine: idxd: add sysfs ABI for idxd driver
dmaengine: idxd: add configuration component of driver
dmaengine: idxd: Init and probe for Intel data accelerators
dmaengine: add support to dynamic register/unregister of channels
dmaengine: break out channel registration
x86/asm: add iosubmit_cmds512() based on MOVDIR64B CPU instruction
dmaengine: ti: k3-udma: fix spelling mistake "limted" -> "limited"
dmaengine: s3c24xx-dma: fix spelling mistake "to" -> "too"
dmaengine: Move dma_get_{,any_}slave_channel() to private dmaengine.h
dmaengine: Remove dma_request_slave_channel_compat() wrapper
dmaengine: Remove dma_device_satisfies_mask() wrapper
dt-bindings: fsl-imx-sdma: Add i.MX8MM/i.MX8MN/i.MX8MP compatible string
dmaengine: zynqmp_dma: fix burst length configuration
dmaengine: sun4i: Add support for cyclic requests with dedicated DMA
dmaengine: fsl-qdma: fix duplicated argument to &&
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
"This time it's surprisingly quiet (probably due to the christmas
break):
- Logitech HID++ protocol improvements from Mazin Rezk, Pedro
Vanzella and Adrian Freund
- support for hidraw uniq ioctl from Marcel Holtmann"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-hidpp: avoid duplicate error handling code in 'hidpp_probe()'
hid-logitech-hidpp: read battery voltage from newer devices
HID: logitech: Add MX Master 3 Mouse
HID: logitech-hidpp: Support WirelessDeviceStatus connect events
HID: logitech-hidpp: Support translations from short to long reports
HID: hidraw: add support uniq ioctl
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- Enable thermal policy for ASUS TUF FX705DY/FX505DY
- Support left round button on ASUS N56VB
- Support new Mellanox platforms of basic class VMOD0009 and VMOD0010
- Intel Comet Lake, Tiger Lake and Elkhart Lake support in the PMC
driver
- Big clean-up to Intel PMC core, PMC IPC and SCU IPC drivers
- Touchscreen support for the PiPO W11 tablet
* tag 'platform-drivers-x86-v5.6-1' of git://git.infradead.org/linux-platform-drivers-x86: (64 commits)
platform/x86: intel_pmc_ipc: Switch to use driver->dev_groups
platform/x86: intel_pmc_ipc: Propagate error from kstrtoul()
platform/x86: intel_pmc_ipc: Use octal permissions in sysfs attributes
platform/x86: intel_pmc_ipc: Get rid of unnecessary includes
platform/x86: intel_pmc_ipc: Drop ipc_data_readb()
platform/x86: intel_pmc_ipc: Drop intel_pmc_gcr_read() and intel_pmc_gcr_write()
platform/x86: intel_pmc_ipc: Make intel_pmc_ipc_raw_cmd() static
platform/x86: intel_pmc_ipc: Make intel_pmc_ipc_simple_command() static
platform/x86: intel_pmc_ipc: Make intel_pmc_gcr_update() static
platform/x86: intel_scu_ipc: Reformat kernel-doc comments of exported functions
platform/x86: intel_scu_ipc: Drop intel_scu_ipc_raw_command()
platform/x86: intel_scu_ipc: Drop intel_scu_ipc_io[read|write][8|16]()
platform/x86: intel_scu_ipc: Drop unused macros
platform/x86: intel_scu_ipc: Drop unused prototype intel_scu_ipc_fw_update()
platform/x86: intel_scu_ipc: Sleeping is fine when polling
platform/x86: intel_scu_ipc: Drop intel_scu_ipc_i2c_cntrl()
platform/x86: intel_scu_ipc: Remove Lincroft support
platform/x86: intel_scu_ipc: Add constants for register offsets
platform/x86: intel_scu_ipc: Fix interrupt support
platform/x86: intel_scu_ipcutil: Remove default y from Kconfig
...
|
|
Pull MMC updates from Ulf Hansson:
"There are no updates for the MEMSTICK subsystem this time. But note
that I am also carrying a patch from the pinctrl tree, which has been
shared through an immutable branch.
Summary:
MMC core:
- Convert to reasonable timeouts for all CMD6 commands (updates for
BKOPS, CACHE_FLUSH and INAND_CMD38_ARG_EXT_CSD) for eMMC
- Respect f_max clock rate at card initialization
- Add gpiod_toggle_active_low() API
- Consolidate slot-gpio code by using gpiod_toggle_active_low()
MMC host:
- Add pinctrl_select_default_state() API
- Consolidate pintctrl code by using pinctrl_select_default_state()
- mmci: Support any block sizes for SDIO for some variants
- mmci: Enable reset control for stm32_sdmmc
- mmc_spi: Toggle SPI_CS_HIGH polarity rather than hard-coding it
- renesas_sdhi: Add support for the r8a77961 variant
- renesas_sdhi: A few minor improvements
- rockchip-dw-mshc: Add support for the rk3308 variant
- sdhci: Enable support for external DMA controllers
- sdhci: Fixup error path when sending CMD12
- sdhci-brcmstb: Add support for 7216b0 variant
- sdhci-brcmstb: Add support for command queuing (CQHCI)
- sdhci-brcmstb: Add support for eMMC HS400ES mode
- sdhci-msm: Add support for the sc7180 variant
- sdhci-msm: Add support for command queuing (CQHCI)
- sdhci-of-at91: Add support for the SAM9x60 variant
- sdhci-of-at91: Improve support for tunings
- sdhci-of-esdhc: A few fixups for some clock related issues
- sdhci-omap: Add support for the am335x and the am437x variants
- sdhci-omap: Improve support for erase operations
- sdhci-omap: Add support for external DMA"
* tag 'mmc-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (89 commits)
mmc: core: Default to generic_cmd6_time as timeout in __mmc_switch()
mmc: block: Use generic_cmd6_time when modifying INAND_CMD38_ARG_EXT_CSD
mmc: core: Specify timeouts for BKOPS and CACHE_FLUSH for eMMC
mmc: sdhci-cadence: remove unneeded 'inline' marker
dt-bindings: mmc: rockchip-dw-mshc: add description for rk3308
dt-bindings: mmc: convert rockchip dw-mshc bindings to yaml
dt-bindings: mmc: convert synopsys dw-mshc bindings to yaml
mmc: sdhci-msm: Add CQHCI support for sdhci-msm
mmc: sdhci: Let a vendor driver supply and update ADMA descriptor size
mmc: sdhci-of-esdhc: fix serious issue clock is always disabled
mmc: sdhci-of-esdhc: fix transfer mode register reading
mmc: sdhci-brcmstb: Fix incorrect switch to HS mode
mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)
mmc: sdhci-brcmstb: Add shutdown callback
mmc: sdhci-brcmstb: Fix driver to defer on clk_get defer
mmc: sdhci-brcmstb: Add ability to use HS400ES transfer mode
dt-bindings: mmc: brcm,sdhci-brcmstb: Add support for 7216b0
mmc: core: limit probe clock frequency to configured f_max
mmc: sdhci-milbeaut: Remove redundant platform_get_irq error message
mmc: sdhci: fix an issue of mixing different types
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Boris Brezillon:
"Core changes:
- Make i3c_bus_set_mode() static
Driver changes:
- Add a per-SoC data_hold_delay property to the Cadence driver
- Fix formatting issues in the 'CADENCE I3C MASTER IP' MAINTAINERS
entry
- Use devm_platform_ioremap_resource() where appropriate
- Adjust DesignWare reattach logic"
* tag 'i3c/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw: reattach device on first available location of address table
i3c: master: cdns: convert to devm_platform_ioremap_resource
i3c: master: dw: convert to devm_platform_ioremap_resource
MAINTAINERS: fix style in CADENCE I3C MASTER IP entry
i3c: master: make i3c_bus_set_mode static
i3c: master: cdns: add data hold delay support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS updates from Borislav Petkov:
- Misc fixes to the MCE code all over the place, by Jan H. Schönherr.
- Initial support for AMD F19h and other cleanups to amd64_edac, by
Yazen Ghannam.
- Other small cleanups.
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
EDAC/mce_amd: Make fam_ops static global
EDAC/amd64: Drop some family checks for newer systems
EDAC/amd64: Add family ops for Family 19h Models 00h-0Fh
x86/amd_nb: Add Family 19h PCI IDs
EDAC/mce_amd: Always load on SMCA systems
x86/MCE/AMD, EDAC/mce_amd: Add new Load Store unit McaType
x86/mce: Fix use of uninitialized MCE message string
x86/mce: Fix mce=nobootlog
x86/mce: Take action on UCNA/Deferred errors again
x86/mce: Remove mce_inject_log() in favor of mce_log()
x86/mce: Pass MCE message to mce_panic() on failed kernel recovery
x86/mce/therm_throt: Mark throttle_active_work() as __maybe_unused
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
"A totally boring branch this time around: a garden variety of small
fixes all over the place"
* tag 'edac_for_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/amd64: Do not warn when removing instances
EDAC/sifive: Fix return value check in ecc_register()
EDAC/aspeed: Remove unneeded semicolon
EDAC: remove set but not used variable 'ecc_loc'
EDAC: skx_common: downgrade message importance on missing PCI device
EDAC/Kconfig: Fix Kconfig indentation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"core:
- Add support for enable attributes to hwmon core
- Add intrusion templates
pmbus:
- Support for Infineon Multi-phase xdpe122 family controllers
- Support for Intel IMVP9 and AMD 6.25mV modes
- Support for vid mode detection per page bases
- Detect if chip is write protected
- Support for MAX20730, MAX20734, MAX20743, MAX20796, UCD90320,
TPS53688
- Various improvements to ibm-cffps driver
k10temp:
- Support for additional temperature sensors as well as voltage and
current telemetry for Zen CPUs
w83627ehf:
- Remove support for NCT6775, NCT6776 (they have their own driver)
New drivers:
- ADM1177
- MAX31730
- Driver for disk and solid state drives with temperature sensors
Other:
- pwm-fan: stop fan on shutdown"
* tag 'hwmon-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (35 commits)
hwmon: (k10temp) Display up to eight sets of CCD temperatures
hwmon: (k10temp) Add debugfs support
hwmon: (k10temp) Don't show temperature limits on Ryzen (Zen) CPUs
hwmon: (k10temp) Show core and SoC current and voltages on Ryzen CPUs
hwmon: (k10temp) Report temperatures per CPU die
hmon: (k10temp) Convert to use devm_hwmon_device_register_with_info
hwmon: (k10temp) Use bitops
hwmon: (pwm-fan) stop fan on shutdown
MAINTAINERS: add entry for ADM1177 driver
dt-binding: hwmon: Add documentation for ADM1177
hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver
docs: hwmon: Include 'xdpe12284.rst' into docs
hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers
hwmon: (pmbus/tps53679) Extend device list supported by driver
hwmon: (pmbus/core) Add support for Intel IMVP9 and AMD 6.25mV modes
hwmon: (pmbus/core) Add support for vid mode detection per page bases
hwmon: (pmbus/ibm-cffps) Prevent writing on_off_config with bad data
hwmon: (w83627ehf) Remove set but not used variable 'fan4min'
hwmon: Driver for disk and solid state drives with temperature sensors
hwmon: (pmbus/ibm-cffps) Fix the LED behavior when turned off
...
|
|
Pull tpm updates from Jarkko Sakkinen:
"This adds a new sysfs file for querying TPM major version, which can
be used by the user space the TPM protocol used to communicate with
the chip"
* tag 'tpmdd-next-20200122' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: Add tpm_version_major sysfs file
tpm: Update mailing list contact information in sysfs-class-tpm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The changes are a real mixed bag this time around.
The only scary looking one from the diffstat is the uapi change to
asm-generic/mman-common.h, but this has been acked by Arnd and is
actually just adding a pair of comments in an attempt to prevent
allocation of some PROT values which tend to get used for
arch-specific purposes. We'll be using them for Branch Target
Identification (a CFI-like hardening feature), which is currently
under review on the mailing list.
New architecture features:
- Support for Armv8.5 E0PD, which benefits KASLR in the same way as
KPTI but without the overhead. This allows KPTI to be disabled on
CPUs that are not affected by Meltdown, even is KASLR is enabled.
- Initial support for the Armv8.5 RNG instructions, which claim to
provide access to a high bandwidth, cryptographically secure
hardware random number generator. As well as exposing these to
userspace, we also use them as part of the KASLR seed and to seed
the crng once all CPUs have come online.
- Advertise a bunch of new instructions to userspace, including
support for Data Gathering Hint, Matrix Multiply and 16-bit
floating point.
Kexec:
- Cleanups in preparation for relocating with the MMU enabled
- Support for loading crash dump kernels with kexec_file_load()
Perf and PMU drivers:
- Cleanups and non-critical fixes for a couple of system PMU drivers
FPU-less (aka broken) CPU support:
- Considerable fixes to support CPUs without the FP/SIMD extensions,
including their presence in heterogeneous systems. Good luck
finding a 64-bit userspace that handles this.
Modern assembly function annotations:
- Start migrating our use of ENTRY() and ENDPROC() over to the
new-fangled SYM_{CODE,FUNC}_{START,END} macros, which are intended
to aid debuggers
Kbuild:
- Cleanup detection of LSE support in the assembler by introducing
'as-instr'
- Remove compressed Image files when building clean targets
IP checksumming:
- Implement optimised IPv4 checksumming routine when hardware offload
is not in use. An IPv6 version is in the works, pending testing.
Hardware errata:
- Work around Cortex-A55 erratum #1530923
Shadow call stack:
- Work around some issues with Clang's integrated assembler not
liking our perfectly reasonable assembly code
- Avoid allocating the X18 register, so that it can be used to hold
the shadow call stack pointer in future
ACPI:
- Fix ID count checking in IORT code. This may regress broken
firmware that happened to work with the old implementation, in
which case we'll have to revert it and try something else
- Fix DAIF corruption on return from GHES handler with pseudo-NMIs
Miscellaneous:
- Whitelist some CPUs that are unaffected by Spectre-v2
- Reduce frequency of ASID rollover when KPTI is compiled in but
inactive
- Reserve a couple of arch-specific PROT flags that are already used
by Sparc and PowerPC and are planned for later use with BTI on
arm64
- Preparatory cleanup of our entry assembly code in preparation for
moving more of it into C later on
- Refactoring and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (73 commits)
arm64: acpi: fix DAIF manipulation with pNMI
arm64: kconfig: Fix alignment of E0PD help text
arm64: Use v8.5-RNG entropy for KASLR seed
arm64: Implement archrandom.h for ARMv8.5-RNG
arm64: kbuild: remove compressed images on 'make ARCH=arm64 (dist)clean'
arm64: entry: Avoid empty alternatives entries
arm64: Kconfig: select HAVE_FUTEX_CMPXCHG
arm64: csum: Fix pathological zero-length calls
arm64: entry: cleanup sp_el0 manipulation
arm64: entry: cleanup el0 svc handler naming
arm64: entry: mark all entry code as notrace
arm64: assembler: remove smp_dmb macro
arm64: assembler: remove inherit_daif macro
ACPI/IORT: Fix 'Number of IDs' handling in iort_id_map()
mm: Reserve asm-generic prot flags 0x10 and 0x20 for arch use
arm64: Use macros instead of hard-coded constants for MAIR_EL1
arm64: Add KRYO{3,4}XX CPU cores to spectre-v2 safe list
arm64: kernel: avoid x18 in __cpu_soft_restart
arm64: kvm: stop treating register x18 as caller save
arm64/lib: copy_page: avoid x18 register in assembler code
...
|
|
- voltage support for newer Logitech HID++ devices, from Pedro Vanzella.
- MX Master support improvements, from Adrian Freund and Mazin Rezk
|
|
- support for uniq ioctl()
|
|
Pull block fix from Jens Axboe:
"Unfortunately this weekend we had a few last minute reports, one was
for block.
The partition disable for zoned devices was overly restrictive, it can
work (and be supported) just fine for host-aware variants.
Here's a fix ensuring that's the case so we don't break existing users
of that"
* tag 'block-5.5-2020-01-26' of git://git.kernel.dk/linux-block:
block: allow partitions on host aware zone devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two last minute fixes, both in drivers.
The fnic one is a highly unlikely condition, but the RDMA one is a
recently introduced regression that causes a kernel warning to trigger
in every RDMA logon, which would be unsightly if it got into the final
release"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: RDMA/isert: Fix a recently introduced regression related to logout
scsi: fnic: do not queue commands during fwreset
|
|
Host-aware SMR drives can be used with the commands to explicitly manage
zone state, but they can also be used as normal disks. In the former
case it makes perfect sense to allow partitions on them, in the latter
it does not, just like for host managed devices. Add a check to
add_partition to allow partitions on host aware devices, but give
up any zone management capabilities in that case, which also catches
the previously missed case of adding a partition vs just scanning it.
Because sd can rescan the attribute at runtime it needs to check if
a disk has partitions, for which a new helper is added to genhd.h.
Fixes: 5eac3eb30c9a ("block: Remove partition support for zoned block devices")
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull networking fixes from David Miller:
1) Off by one in mt76 airtime calculation, from Dan Carpenter.
2) Fix TLV fragment allocation loop condition in iwlwifi, from Luca
Coelho.
3) Don't confirm neigh entries when doing ipsec pmtu updates, from Xu
Wang.
4) More checks to make sure we only send TSO packets to lan78xx chips
that they can actually handle. From James Hughes.
5) Fix ip_tunnel namespace move, from William Dauchy.
6) Fix unintended packet reordering due to cooperation between
listification done by GRO and non-GRO paths. From Maxim
Mikityanskiy.
7) Add Jakub Kicincki formally as networking co-maintainer.
8) Info leak in airo ioctls, from Michael Ellerman.
9) IFLA_MTU attribute needs validation during rtnl_create_link(), from
Eric Dumazet.
10) Use after free during reload in mlxsw, from Ido Schimmel.
11) Dangling pointers are possible in tp->highest_sack, fix from Eric
Dumazet.
12) Missing *pos++ in various networking seq_next handlers, from Vasily
Averin.
13) CHELSIO_GET_MEM operation neds CAP_NET_ADMIN check, from Michael
Ellerman.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (109 commits)
firestream: fix memory leaks
net: cxgb3_main: Add CAP_NET_ADMIN check to CHELSIO_GET_MEM
net: bcmgenet: Use netif_tx_napi_add() for TX NAPI
tipc: change maintainer email address
net: stmmac: platform: fix probe for ACPI devices
net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path
net/mlx5e: kTLS, Remove redundant posts in TX resync flow
net/mlx5e: kTLS, Fix corner-case checks in TX resync flow
net/mlx5e: Clear VF config when switching modes
net/mlx5: DR, use non preemptible call to get the current cpu number
net/mlx5: E-Switch, Prevent ingress rate configuration of uplink rep
net/mlx5: DR, Enable counter on non-fwd-dest objects
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Fix lowest FDB pool size
net: Fix skb->csum update in inet_proto_csum_replace16().
netfilter: nf_tables: autoload modules from the abort path
netfilter: nf_tables: add __nft_chain_type_get()
netfilter: nf_tables_offload: fix check the chain offload flag
netfilter: conntrack: sctp: use distinct states for new SCTP connections
ipv6_route_seq_next should increase position index
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A couple of fixes have come in that would be good to include in this
release:
- A fix for amount of memory on Beaglebone Black. Surfaced now since
GRUB2 doesn't update memory size in the booted kernel.
- A fix to make SPI interfaces work on am43x-epos-evm.
- Small Kconfig fix for OPTEE (adds a depend on MMU) to avoid build
failures"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
tee: optee: Fix compilation issue with nommu
ARM: dts: am335x-boneblack-common: fix memory size
|
|
In fs_open(), 'vcc' is allocated through kmalloc() and assigned to
'atm_vcc->dev_data.' In the following execution, if an error occurs, e.g.,
there is no more free channel, an error code EBUSY or ENOMEM will be
returned. However, 'vcc' is not deallocated, leading to memory leaks. Note
that, in normal cases where fs_open() returns 0, 'vcc' will be deallocated
in fs_close(). But, if fs_open() fails, there is no guarantee that
fs_close() will be invoked.
To fix this issue, deallocate 'vcc' before the error code is returned.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fix from Linus Walleij:
"A single fix for the Intel Sunrisepoint pin controller that makes the
interrupts work properly on it"
* tag 'pinctrl-v5.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-01-24
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
Merge conflict: once merge with net-next, a contextual conflict will
appear in drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c
since the code moved in net-next.
To resolve, just delete ALL of the conflicting hunk from net.
So sorry for the small mess ..
For -stable v5.4:
('net/mlx5: Update the list of the PCI supported devices')
('net/mlx5: Fix lowest FDB pool size')
('net/mlx5e: kTLS, Fix corner-case checks in TX resync flow')
('net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path')
('net/mlx5: Eswitch, Prevent ingress rate configuration of uplink rep')
('net/mlx5e: kTLS, Remove redundant posts in TX resync flow')
('net/mlx5: DR, Enable counter on non-fwd-dest objects')
('net/mlx5: DR, use non preemptible call to get the current cpu number')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cxgb3 driver for "Chelsio T3-based gigabit and 10Gb Ethernet
adapters" implements a custom ioctl as SIOCCHIOCTL/SIOCDEVPRIVATE in
cxgb_extension_ioctl().
One of the subcommands of the ioctl is CHELSIO_GET_MEM, which appears
to read memory directly out of the adapter and return it to userspace.
It's not entirely clear what the contents of the adapter memory
contains, but the assumption is that it shouldn't be accessible to all
users.
So add a CAP_NET_ADMIN check to the CHELSIO_GET_MEM case. Put it after
the is_offload() check, which matches two of the other subcommands in
the same function which also check for is_offload() and CAP_NET_ADMIN.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before commit 7587935cfa11 ("net: bcmgenet: move NAPI initialization to
ring initialization") moved the code, this used to be
netif_tx_napi_add(), but we lost that small semantic change in the
process, restore that.
Fixes: 7587935cfa11 ("net: bcmgenet: move NAPI initialization to ring initialization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use generic device API to get phy mode to fix probe failure
with ACPI based devices.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- add sanity checks to USB endpoints in various dirvers
- max77650-onkey was missing an OF table which was preventing module
autoloading
- a revert and a different fix for F54 handling in Synaptics dirver
- a fixup for handling register in pm8xxx vibrator driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: pm8xxx-vib - fix handling of separate enable register
Input: keyspan-remote - fix control-message timeouts
Input: max77650-onkey - add of_match table
Input: rmi_f54 - read from FIFO in 32 byte blocks
Revert "Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers"
Input: sur40 - fix interface sanity checks
Input: gtco - drop redundant variable reinit
Input: gtco - fix extra-descriptor debug message
Input: gtco - fix endpoint sanity check
Input: aiptek - use descriptors of current altsetting
Input: aiptek - fix endpoint sanity check
Input: pegasus_notetaker - fix endpoint sanity check
Input: sun4i-ts - add a check for devm_thermal_zone_of_sensor_register
Input: evdev - convert kzalloc()/vzalloc() to kvzalloc()
|
|
https://git.linaro.org:/people/jens.wiklander/linux-tee into arm/fixes
Fix OP-TEE compile error with nommu
* tag 'tee-optee-fix2-for-5.5' of https://git.linaro.org:/people/jens.wiklander/linux-tee:
tee: optee: Fix compilation issue with nommu
Link: https://lore.kernel.org/r/20200123101310.GA10320@jax
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When TCP out-of-order is identified (unexpected tcp seq mismatch), driver
analyzes the packet and decides what handling should it get:
1. go to accelerated path (to be encrypted in HW),
2. go to regular xmit path (send w/o encryption),
3. drop.
Packets marked with skb->decrypted by the TLS stack in the TX flow skips
SW encryption, and rely on the HW offload.
Verify that such packets are never sent un-encrypted on the wire.
Add a WARN to catch such bugs, and prefer dropping the packet in these cases.
Fixes: 46a3ea98074e ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The call to tx_post_resync_params() is done earlier in the flow,
the post of the control WQEs is unnecessarily repeated. Remove it.
Fixes: 700ec4974240 ("net/mlx5e: kTLS, Fix missing SQ edge fill")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There are the following cases:
1. Packet ends before start marker: bypass offload.
2. Packet starts before start marker and ends after it: drop,
not supported, breaks contract with kernel.
3. packet ends before tls record info starts: drop,
this packet was already acknowledged and its record info
was released.
Add the above as comment in code.
Mind possible wraparounds of the TCP seq, replace the simple comparison
with a call to the TCP before() method.
In addition, remove logic that handles negative sync_len values,
as it became impossible.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Fixes: 46a3ea98074e ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently VF in LEGACY mode are not able to go up. Also in OFFLOADS
mode, when switching to it first time, VF can go up independently to
his representor, which is not expected.
Perform clearing of VF config when switching modes and set link state
to AUTO as default value. Also, when switching to OFFLOADS mode set
link state to DOWN, which allow VF link state to be controlled by its
REP.
Fixes: 1ab2068a4c66 ("net/mlx5: Implement vports admin state backup/restore")
Fixes: 556b9d16d3f5 ("net/mlx5: Clear VF's configuration on disabling SRIOV")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use raw_smp_processor_id instead of smp_processor_id() otherwise we will
get the following trace in debug-kernel:
BUG: using smp_processor_id() in preemptible [00000000] code: devlink
caller is dr_create_cq.constprop.2+0x31d/0x970 [mlx5_core]
Call Trace:
dump_stack+0x9a/0xf0
debug_smp_processor_id+0x1f3/0x200
dr_create_cq.constprop.2+0x31d/0x970
genl_family_rcv_msg+0x5fd/0x1170
genl_rcv_msg+0xb8/0x160
netlink_rcv_skb+0x11e/0x340
Fixes: 297cccebdc5a ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Since the implementation relies on limiting the VF transmit rate to
simulate ingress rate limiting, and since either uplink representor or
ecpf are not associated with a VF, we limit the rate limit configuration
for those ports.
Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The current code handles only counters that attached to dest, we still
have the cases where we have counter on non-dest, like over drop etc.
Fixes: 6a48faeeca10 ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the upcoming ConnectX-7 device ID.
Fixes: 85327a9c4150 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The pool sizes represent the pool sizes in the fw. when we request
a pool size from fw, it will return the next possible group.
We track how many pools the fw has left and start requesting groups
from the big to the small.
When we start request 4k group, which doesn't exists in fw, fw
wants to allocate the next possible size, 64k, but will fail since
its exhausted. The correct smallest pool size in fw is 128 and not 4k.
Fixes: e52c28024008 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Two fixes:
- Fix NULL-ptr dereference bug in Intel IOMMU driver
- Properly save and restore AMD IOMMU performance counter registers
when testing if they are writable"
* tag 'iommu-fixes-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix IOMMU perf counter clobbering during init
iommu/vt-d: Call __dmar_remove_one_dev_info with valid pointer
|
|
Pull drm fixes from Dave Airlie:
"This one has a core mst fix and two i915 fixes. amdgpu just enables
some hw outside experimental.
The panfrost fix is a little bigger than I'd like at this stage but it
fixes a fairly fundamental problem with global shared buffers in that
driver, and since it's confined to that driver and I've taken a look
at it, I think it's fine to get into the tree now, so it can get
stable propagated as well.
core/mst:
- Fix SST branch device handling
amdgpu:
- enable renoir outside experimental
i915:
- Avoid overflow with huge userptr objects
- uAPI fix to correctly handle negative values in
engine->uabi_class/instance (cc: stable)
panfrost:
- Fix mapping of globally visible BO's (Boris)"
* tag 'drm-fixes-2020-01-24' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: remove the experimental flag for renoir
drm/panfrost: Add the panfrost_gem_mapping concept
drm/i915: Align engine->uabi_class/instance with i915_drm.h
drm/i915/userptr: fix size calculation
drm/dp_mst: Handle SST-only branch device case
|
|
init_iommu_perf_ctr() clobbers the register when it checks write access
to IOMMU perf counters and fails to restore when they are writable.
Add save and restore to fix it.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fixes: 30861ddc9cca4 ("perf/x86/amd: Add IOMMU Performance Counter resource management")
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
It is possible for archdata.iommu to be set to
DEFER_DEVICE_DOMAIN_INFO or DUMMY_DEVICE_DOMAIN_INFO so check for
those values before calling __dmar_remove_one_dev_info. Without a
check it can result in a null pointer dereference. This has been seen
while booting a kdump kernel on an HP dl380 gen9.
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: stable@vger.kernel.org # 5.3+
Cc: linux-kernel@vger.kernel.org
Fixes: ae23bfb68f28 ("iommu/vt-d: Detach domain before using a private one")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
All callers of __mmc_switch() should now be specifying a valid timeout for
the CMD6 command. However, just to be sure, let's print a warning and
default to use the generic_cmd6_time in case the provided timeout_ms
argument is zero.
In this context, let's also simplify some of the corresponding code and
clarify some related comments.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-4-ulf.hansson@linaro.org
|
|
The INAND_CMD38_ARG_EXT_CSD is a vendor specific EXT_CSD register, which is
used to prepare an erase/trim operation. However, it doesn't make sense to
use a timeout of 10 minutes while updating the register, which becomes the
case when the timeout_ms argument for mmc_switch() is set to zero.
Instead, let's use the generic_cmd6_time, as that seems like a reasonable
timeout to use for these cases.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-3-ulf.hansson@linaro.org
|
|
The timeout values used while waiting for a CMD6 for BKOPS or a CACHE_FLUSH
to complete, are not defined by the eMMC spec. However, a timeout of 10
minutes as is currently being used, is just silly for both of these cases.
Instead, let's specify more reasonable timeouts, 120s for BKOPS and 30s for
CACHE_FLUSH.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-2-ulf.hansson@linaro.org
|
|
'static inline' in .c files does not make much sense because
functions may or may not be inlined irrespective of the 'inline'
marker. It is just a hint.
This function is quite small, so very likely to be inlined by the
compiler's optimization (-O2 or -Os), but it is up to the compiler
after all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200121105858.13325-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This adds CQHCI support for sdhci-msm platforms.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579194192-7942-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Let a vendor driver supply the maximum descriptor size that it
can operate on. ADMA descriptor table would be allocated using this
supplied size.
If any SD Host controller is of version prior to v4.10 spec
but supports 16byte descriptor, this change allows them to supply
correct descriptor size for ADMA table allocation.
Also let a vendor driver update the descriptor size by overriding
sdhc_host->desc_size if it has to operates on a different descriptor
sizes in different conditions.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579531122-28341-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a hw_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently it is not easy to find out which DMA channels are in use, and
which slave devices are using which channels.
Fix this by creating two symlinks between the DMA channel and the actual
slave device when a channel is requested:
1. A "slave" symlink from DMA channel to slave device,
2. A "dma:<name>" symlink slave device to DMA channel.
When the channel is released, the symlinks are removed again.
The latter requires keeping track of the slave device and the channel
name in the dma_chan structure.
Note that this is limited to channel request functions for requesting an
exclusive slave channel that take a device pointer (dma_request_chan()
and dma_request_slave_channel*()).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Link: https://lore.kernel.org/r/20200117153056.31363-1-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
