| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit ca465e1f1f9b38fe916a36f7d80c5d25f2337c81 ]
If cma_listen_on_all() fails it leaves the per-device ID still on the
listen_list but the state is not set to RDMA_CM_ADDR_BOUND.
When the cmid is eventually destroyed cma_cancel_listens() is not called
due to the wrong state, however the per-device IDs are still holding the
refcount preventing the ID from being destroyed, thus deadlocking:
task:rping state:D stack: 0 pid:19605 ppid: 47036 flags:0x00000084
Call Trace:
__schedule+0x29a/0x780
? free_unref_page_commit+0x9b/0x110
schedule+0x3c/0xa0
schedule_timeout+0x215/0x2b0
? __flush_work+0x19e/0x1e0
wait_for_completion+0x8d/0xf0
_destroy_id+0x144/0x210 [rdma_cm]
ucma_close_id+0x2b/0x40 [rdma_ucm]
__destroy_id+0x93/0x2c0 [rdma_ucm]
? __xa_erase+0x4a/0xa0
ucma_destroy_id+0x9a/0x120 [rdma_ucm]
ucma_write+0xb8/0x130 [rdma_ucm]
vfs_write+0xb4/0x250
ksys_write+0xb5/0xd0
? syscall_trace_enter.isra.19+0x123/0x190
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Ensure that cma_listen_on_all() atomically unwinds its action under the
lock during error.
Fixes: c80a0c52d85c ("RDMA/cma: Add missing error handling of listen_id")
Link: https://lore.kernel.org/r/20210913093344.17230-1-thomas.liu@ucloud.cn
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2cc74e1ee31d00393b6698ec80b322fd26523da4 ]
ROCE uses IGMP for Multicast instead of the native Infiniband system where
joins are required in order to post messages on the Multicast group. On
Ethernet one can send Multicast messages to arbitrary addresses without
the need to subscribe to a group.
So ROCE correctly does not send IGMP joins during rdma_join_multicast().
F.e. in cma_iboe_join_multicast() we see:
if (addr->sa_family == AF_INET) {
if (gid_type == IB_GID_TYPE_ROCE_UDP_ENCAP) {
ib.rec.hop_limit = IPV6_DEFAULT_HOPLIMIT;
if (!send_only) {
err = cma_igmp_send(ndev, &ib.rec.mgid,
true);
}
}
} else {
So the IGMP join is suppressed as it is unnecessary.
However no such check is done in destroy_mc(). And therefore leaving a
sendonly multicast group will send an IGMP leave.
This means that the following scenario can lead to a multicast receiver
unexpectedly being unsubscribed from a MC group:
1. Sender thread does a sendonly join on MC group X. No IGMP join
is sent.
2. Receiver thread does a regular join on the same MC Group x.
IGMP join is sent and the receiver begins to get messages.
3. Sender thread terminates and destroys MC group X.
IGMP leave is sent and the receiver no longer receives data.
This patch adds the same logic for sendonly joins to destroy_mc() that is
also used in cma_iboe_join_multicast().
Fixes: ab15c95a17b3 ("IB/core: Support for CMA multicast join flags")
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2109081340540.668072@gentwo.de
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9f52c25f59b504a29dda42d83ac1e24d2af535d4 upstream.
didn't read the value of mmCP_HQD_QUANTUM from correct
register offset
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d942856865c733ff60450de9691af796ad71d7bc upstream.
[why]
pci deviceid not passed to dal dc, without proper break,
dcn2.x falls into dcn3.x code path
[how]
pass in pci deviceid, and break once dal_version initialized.
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc0bdc5afaa740d782fbf936aaeebd65e5c2921d upstream.
If the state is not idle then rdma_bind_addr() will immediately fail and
no change to global state should happen.
For instance if the state is already RDMA_CM_LISTEN then this will corrupt
the src_addr and would cause the test in cma_cancel_operation():
if (cma_any_addr(cma_src_addr(id_priv)) && !id_priv->cma_dev)
To view a mangled src_addr, eg with a IPv6 loopback address but an IPv4
family, failing the test.
This would manifest as this trace from syzkaller:
BUG: KASAN: use-after-free in __list_add_valid+0x93/0xa0 lib/list_debug.c:26
Read of size 8 at addr ffff8881546491e0 by task syz-executor.1/32204
CPU: 1 PID: 32204 Comm: syz-executor.1 Not tainted 5.12.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
__list_add_valid+0x93/0xa0 lib/list_debug.c:26
__list_add include/linux/list.h:67 [inline]
list_add_tail include/linux/list.h:100 [inline]
cma_listen_on_all drivers/infiniband/core/cma.c:2557 [inline]
rdma_listen+0x787/0xe00 drivers/infiniband/core/cma.c:3751
ucma_listen+0x16a/0x210 drivers/infiniband/core/ucma.c:1102
ucma_write+0x259/0x350 drivers/infiniband/core/ucma.c:1732
vfs_write+0x28e/0xa30 fs/read_write.c:603
ksys_write+0x1ee/0x250 fs/read_write.c:658
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Which is indicating that an rdma_id_private was destroyed without doing
cma_cancel_listens().
Instead of trying to re-use the src_addr memory to indirectly create an
any address build one explicitly on the stack and bind to that as any
other normal flow would do.
Link: https://lore.kernel.org/r/0-v1-9fbb33f5e201+2a-cma_listen_jgg@nvidia.com
Cc: stable@vger.kernel.org
Fixes: 732d41c545bb ("RDMA/cma: Make the locking for automatic state transition more clear")
Reported-by: syzbot+6bb0528b13611047209c@syzkaller.appspotmail.com
Tested-by: Hao Sun <sunhao.th@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0c15b360fb65ee39849afe987c16eb3d0175d0d upstream.
If the IR Toy is receiving IR while a transmit is done, it may end up
hanging. We can prevent this from happening by re-entering sample mode
just before issuing the transmit command.
Link: https://github.com/bengtmartensson/HarcHardware/discussions/25
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8c2da7e329ce004fee748b921e4c765dc2fa338 upstream.
Fix incorrect index for UTMRD reference in ufshcd_add_tm_upiu_trace().
Link: https://lore.kernel.org/r/20210924085848.25500-1-jonathan.hsu@mediatek.com
Fixes: 4b42d557a8ad ("scsi: ufs: core: Fix wrong Task Tag used in task management request UPIUs")
Cc: stable@vger.kernel.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jonathan Hsu <jonathan.hsu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 540cffbab8b8e6c52a4121666ca18d6e94586ed2 upstream.
Per gpio_chip interface, error shall be proparated to the caller.
Attempt to silent diagnostics by returning zero (as written in the
comment) is plain wrong, because the zero return can be interpreted by
the caller as the gpio value.
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
structure field
commit 943c15ac1b84d378da26bba41c83c67e16499ac4 upstream.
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-1-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
structure field
commit 0f36b88173f028e372668ae040ab1a496834d278 upstream.
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-2-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multipline alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
structure field
commit dd4d747ef05addab887dc8ff0d6ab9860bbcd783 upstream.
If driver read tmp value sufficient for
(tmp & 0x08) && (!(tmp & 0x80)) && ((tmp & 0x7) == ((tmp >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-3-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2938b2978a70d4cc10777ee71c9e512ffe4e0f4b upstream.
Function i2c_smbus_read_byte_data() can return a negative error number
instead of the data read if I2C transaction failed for whatever reason.
Lack of error checking can lead to serious issues on production
hardware, e.g. errors treated as temperatures produce spurious critical
temperature-crossed-threshold errors in BMC logs for OCP server
hardware. The patch was tested with Mellanox OCP Mezzanine card
emulating TMP421 protocol for temperature sensing which sometimes leads
to I2C protocol error during early boot up stage.
Fixes: 9410700b881f ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-1-fercerpav@gmail.com
[groeck: dropped unnecessary line breaks]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f060db99374e80e853ac4916b49f0a903f65e9dc upstream.
When ACPI NFIT table is failing to populate correct numa information
on arm64, dax_kmem will get NUMA_NO_NODE from the NFIT driver.
Without this patch, pmem can't be probed as RAM devices on arm64 guest:
$ndctl create-namespace -fe namespace0.0 --mode=devdax --map=dev -s 1g -a 128M
kmem dax0.0: rejecting DAX region [mem 0x240400000-0x2bfffffff] with invalid node: -1
kmem: probe of dax0.0 failed with error -22
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jia He <justin.he@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: c221c0b0308f ("device-dax: "Hotplug" persistent memory for use like normal RAM")
Link: https://lore.kernel.org/r/20210922152919.6940-1-justin.he@arm.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b69ec50b3e55c4b2a85c8bc46763eaf330605847 ]
For DEV_VER_V3 version there exist race condition between clearing
ep_sts.EP_STS_TRBERR and setting ep_cmd.EP_CMD_DRDY bit.
Setting EP_CMD_DRDY will be ignored by controller when
EP_STS_TRBERR is set. So, between these two instructions we have
a small time gap in which the EP_STSS_TRBERR can be set. In such case
the transfer will not start after setting doorbell.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org> # 5.12.x
Tested-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210907062619.34622-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cdef1196608892b9a46caa5f2b64095a7f0be60c ]
Since commit e5c6b312ce3c ("cpufreq: schedutil: Use kobject release()
method to free sugov_tunables") kobject_put() has kfree()d the
attr_set before gov_attr_set_put() returns.
kobject_put() isn't the last user of attr_set in gov_attr_set_put(),
the subsequent mutex_destroy() triggers a use-after-free:
| BUG: KASAN: use-after-free in mutex_is_locked+0x20/0x60
| Read of size 8 at addr ffff000800ca4250 by task cpuhp/2/20
|
| CPU: 2 PID: 20 Comm: cpuhp/2 Not tainted 5.15.0-rc1 #12369
| Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development
| Platform, BIOS EDK II Jul 30 2018
| Call trace:
| dump_backtrace+0x0/0x380
| show_stack+0x1c/0x30
| dump_stack_lvl+0x8c/0xb8
| print_address_description.constprop.0+0x74/0x2b8
| kasan_report+0x1f4/0x210
| kasan_check_range+0xfc/0x1a4
| __kasan_check_read+0x38/0x60
| mutex_is_locked+0x20/0x60
| mutex_destroy+0x80/0x100
| gov_attr_set_put+0xfc/0x150
| sugov_exit+0x78/0x190
| cpufreq_offline.isra.0+0x2c0/0x660
| cpuhp_cpufreq_offline+0x14/0x24
| cpuhp_invoke_callback+0x430/0x6d0
| cpuhp_thread_fun+0x1b0/0x624
| smpboot_thread_fn+0x5e0/0xa6c
| kthread+0x3a0/0x450
| ret_from_fork+0x10/0x20
Swap the order of the calls.
Fixes: e5c6b312ce3c ("cpufreq: schedutil: Use kobject release() method to free sugov_tunables")
Cc: 4.7+ <stable@vger.kernel.org> # 4.7+
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4a0a542fe5e4273baf9228459ef3f75c29490cba ]
The MSI-X and MSI calls fails in kdump kernel. Because of this
qla2xxx_create_qpair() fails leading to .create_queue callback failure.
The fix is to return existing qpair instead of allocating new one and
allocate a single hw queue.
[ 19.975838] qla2xxx [0000:d8:00.1]-00c7:11: MSI-X: Failed to enable support,
giving up -- 16/-28.
[ 19.984885] qla2xxx [0000:d8:00.1]-0037:11: Falling back-to MSI mode --
ret=-28.
[ 19.992278] qla2xxx [0000:d8:00.1]-0039:11: Falling back-to INTa mode --
ret=-28.
..
..
..
[ 21.141518] qla2xxx [0000:d8:00.0]-2104:2: qla_nvme_alloc_queue: handle
00000000e7ee499d, idx =1, qsize 32
[ 21.151166] qla2xxx [0000:d8:00.0]-0181:2: FW/Driver is not multi-queue capable.
[ 21.158558] qla2xxx [0000:d8:00.0]-2122:2: Failed to allocate qpair
[ 21.164824] nvme nvme0: NVME-FC{0}: reset: Reconnect attempt failed (-22)
[ 21.171612] nvme nvme0: NVME-FC{0}: Reconnect attempt in 2 seconds
Link: https://lore.kernel.org/r/20210810043720.1137-13-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b0c406124719b625b1aba431659f5cdc24a982c ]
This issue happens when a userspace program does an ioctl
FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct
containing only the fields xres, yres, and bits_per_pixel
with values.
If this struct is the same as the previous ioctl, the
vc_resize() detects it and doesn't call the resize_screen(),
leaving the fb_var_screeninfo incomplete. And this leads to
the updatescrollmode() calculates a wrong value to
fbcon_display->vrows, which makes the real_y() return a
wrong value of y, and that value, eventually, causes
the imageblit to access an out-of-bound address value.
To solve this issue I made the resize_screen() be called
even if the screen does not need any resizing, so it will
"fix and fill" the fb_var_screeninfo independently.
Cc: stable <stable@vger.kernel.org> # after 5.15-rc2 is out, give it time to bake
Reported-and-tested-by: syzbot+858dc7a2f7ef07c2c219@syzkaller.appspotmail.com
Signed-off-by: Igor Matheus Andrade Torrente <igormtorrente@gmail.com>
Link: https://lore.kernel.org/r/20210628134509.15895-1-igormtorrente@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 96f5bd03e1be606987644b71899ea56a8d05f825 upstream.
Commit 8480ed9c2bbd56 ("xen/balloon: use a kernel thread instead a
workqueue") switched the Xen balloon driver to use a kernel thread.
Unfortunately the patch omitted to call try_to_freeze() or to use
wait_event_freezable_timeout(), causing a system suspend to fail.
Fixes: 8480ed9c2bbd56 ("xen/balloon: use a kernel thread instead a workqueue")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210920100345.21939-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c32dfec6c1c36bbbcd5d33e949d99aeb215877ec upstream.
Some CP2102 do not support event-insertion mode but return no error when
attempting to enable it.
This means that any event escape characters in the input stream will not
be escaped by the device and consequently regular data may be
interpreted as escape sequences and be removed from the stream by the
driver.
The reporter's device has batch number DCL00X etched into it and as
discovered by the SHA2017 Badge team, counterfeit devices with that
marking can be detected by sending malformed vendor requests. [1][2]
Tests confirm that the possibly counterfeit CP2102 returns a single byte
in response to a malformed two-byte part-number request, while an
original CP2102 returns two bytes. Assume that every CP2102 that behaves
this way also does not support event-insertion mode (e.g. cannot report
parity errors).
[1] https://mobile.twitter.com/sha2017badge/status/1167902087289532418
[2] https://hackaday.com/2017/08/14/hands-on-with-the-shacamp-2017-badge/#comment-3903376
Reported-by: Malte Di Donato <malte@neo-soft.org>
Tested-by: Malte Di Donato <malte@neo-soft.org>
Fixes: a7207e9835a4 ("USB: serial: cp210x: add support for line-status events")
Cc: stable@vger.kernel.org # 5.9
Link: https://lore.kernel.org/r/20210922113100.20888-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8b4bd256674720709a9d858a219fcac6f2f253b5 upstream.
After upgrading to Linux 5.13.3 I noticed my laptop would shutdown due
to overheat (when it should not). It turned out this was due to commit
fe6a6de6692e ("thermal/drivers/int340x/processor_thermal: Fix tcc setting").
What happens is this drivers uses a global variable to keep track of the
tcc offset (tcc_offset_save) and uses it on resume. The issue is this
variable is initialized to 0, but is only set in
tcc_offset_degree_celsius_store, i.e. when the tcc offset is explicitly
set by userspace. If that does not happen, the resume path will set the
offset to 0 (in my case the h/w default being 3, the offset would become
too low after a suspend/resume cycle).
The issue did not arise before commit fe6a6de6692e, as the function
setting the offset would return if the offset was 0. This is no longer
the case (rightfully).
Fix this by not applying the offset if it wasn't saved before, reverting
back to the old logic. A better approach will come later, but this will
be easier to apply to stable kernels.
The logic to restore the offset after a resume was there long before
commit fe6a6de6692e, but as a value of 0 was considered invalid I'm
referencing the commit that made the issue possible in the Fixes tag
instead.
Fixes: fe6a6de6692e ("thermal/drivers/int340x/processor_thermal: Fix tcc setting")
Cc: stable@vger.kernel.org
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210909085613.5577-2-atenart@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54607282fae6148641a08d81a6e0953b541249c7 upstream.
dimm->edac_mode contains values of type enum edac_type - not the
corresponding capability flags. Fix that.
Fixes: 1088750d7839 ("EDAC: Add EDAC driver for DMC520")
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20210916085258.7544-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5297cfa6bdf93e3889f78f9b482e2a595a376083 upstream.
dimm->edac_mode contains values of type enum edac_type - not the
corresponding capability flags. Fix that.
Issue caught by Coverity check "enumerated type mixed with another
type."
[ bp: Rewrite commit message, add tags. ]
Fixes: ae9b56e3996d ("EDAC, synps: Add EDAC support for zynq ddr ecc controller")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20210818072315.15149-1-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit efafec27c5658ed987e720130772f8933c685e87 ]
Without CONFIG_PM enabled, the SET_RUNTIME_PM_OPS() macro ends up being
empty, and the only use of tegra_slink_runtime_{resume,suspend} goes
away, resulting in
drivers/spi/spi-tegra20-slink.c:1200:12: error: ‘tegra_slink_runtime_resume’ defined but not used [-Werror=unused-function]
1200 | static int tegra_slink_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-tegra20-slink.c:1188:12: error: ‘tegra_slink_runtime_suspend’ defined but not used [-Werror=unused-function]
1188 | static int tegra_slink_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
mark the functions __maybe_unused to make the build happy.
This hits the alpha allmodconfig build (and others).
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3c0d2a46c0141913dc6fd126c57d0615677d946e ]
tx timeout and slot time are currently specified in units of HZ. On
Alpha, HZ is defined as 1024. When building alpha:allmodconfig, this
results in the following error message.
drivers/net/hamradio/6pack.c: In function 'sixpack_open':
drivers/net/hamradio/6pack.c:71:41: error:
unsigned conversion from 'int' to 'unsigned char'
changes value from '256' to '0'
In the 6PACK protocol, tx timeout is specified in units of 10 ms and
transmitted over the wire:
https://www.linux-ax25.org/wiki/6PACK
Defining a value dependent on HZ doesn't really make sense, and
presumably comes from the (very historical) situation where HZ was
originally 100.
Note that the SIXP_SLOTTIME use explicitly is about 10ms granularity:
mod_timer(&sp->tx_t, jiffies + ((when + 1) * HZ) / 100);
and the SIXP_TXDELAY walue is sent as a byte over the wire.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dff2d13114f0beec448da9b3716204eb34b0cf41 ]
gcc 11.x reports the following compiler warning/error.
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
Use absolute_pointer() to work around the problem.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7bbee36d71502ab9a341505da89a017c7ae2e6b2 ]
In amdgpu_dm_atomic_check, dc_validate_global_state is called. On
failure this logs a warning to the kernel journal. However warnings
shouldn't be used for atomic test-only commit failures: user-space
might be perfoming a lot of atomic test-only commits to find the
best hardware configuration.
Downgrade the log to a regular DRM atomic message. While at it, use
the new device-aware logging infrastructure.
This fixes error messages in the kernel when running gamescope [1].
[1]: https://github.com/Plagman/gamescope/issues/245
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9817d763dbe15327b9b3ff4404fa6f27f927e744 ]
We should always destroy cm_id before destroy qp to avoid to get cma
event after qp was destroyed, which may lead to use after free.
In RDMA connection establishment error flow, don't destroy qp in cm
event handler.Just report cm_error to upper level, qp will be destroy
in nvme_rdma_alloc_queue() after destroy cm id.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 79f528afa93918519574773ea49a444c104bc1bd ]
nvme_update_ana_state() has a deficiency that results in a failure to
properly update the ana state for a namespace in the following case:
NSIDs in ctrl->namespaces: 1, 3, 4
NSIDs in desc->nsids: 1, 2, 3, 4
Loop iteration 0:
ns index = 0, n = 0, ns->head->ns_id = 1, nsid = 1, MATCH.
Loop iteration 1:
ns index = 1, n = 1, ns->head->ns_id = 3, nsid = 2, NO MATCH.
Loop iteration 2:
ns index = 2, n = 2, ns->head->ns_id = 4, nsid = 4, MATCH.
Where the update to the ANA state of NSID 3 is missed. To fix this
increment n and retry the update with the same ns when ns->head->ns_id is
higher than nsid,
Signed-off-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8480ed9c2bbd56fc86524998e5f2e3e22f5038f6 ]
Today the Xen ballooning is done via delayed work in a workqueue. This
might result in workqueue hangups being reported in case of large
amounts of memory are being ballooned in one go (here 16GB):
BUG: workqueue lockup - pool cpus=6 node=0 flags=0x0 nice=0 stuck for 64s!
Showing busy workqueues and worker pools:
workqueue events: flags=0x0
pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=2/256 refcnt=3
in-flight: 229:balloon_process
pending: cache_reap
workqueue events_freezable_power_: flags=0x84
pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=1/256 refcnt=2
pending: disk_events_workfn
workqueue mm_percpu_wq: flags=0x8
pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=1/256 refcnt=2
pending: vmstat_update
pool 12: cpus=6 node=0 flags=0x0 nice=0 hung=64s workers=3 idle: 2222 43
This can easily be avoided by using a dedicated kernel thread for doing
the ballooning work.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210827123206.15429-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d9a7e9df731670acdc69e81748941ad338f47fab ]
If HWP has been already been enabled by BIOS, it may be
necessary to override some kernel command line parameters.
Once it has been enabled it requires a reset to be disabled.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 08dad2f4d541fcfe5e7bfda72cc6314bbfd2802f ]
The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC.
The divisor used is set in the MAC_MDIO_Address register field CR
(Clock Rate)
The divisor is there to change the CSR clock into a clock that falls
below the IEEE 802.3 specified max frequency of 2.5MHz.
If the CSR clock is 300MHz, the code falls back to using the reset
value in the MAC_MDIO_Address register, as described in the comment
above this code.
However, 300MHz is actually an allowed value and the proper divider
can be estimated quite easily (it's just 1Hz difference!)
A CSR frequency of 300MHz with the maximum clock rate value of 0x5
(STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around
~2.42MHz which is below the IEEE 802.3 specified maximum.
For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz,
and unfortunately, the reset-value of the MAC_MDIO_Address CR field
is 0x0.
This leads to a clock rate of zero and a divisor of 42, and gives an
MDC frequency of ~7.14MHz.
Allow CSR clock of 300MHz by making the comparison inclusive.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d82d5303c4c539db86588ffb5dc5b26c3f1513e8 ]
plat_dev->dev->platform_data is released by platform_device_unregister(),
use of pclk and hclk is a use-after-free. Since device unregister won't
need a clk device we adjust the function call sequence to fix this issue.
[ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci]
[ 31.275563] Freed by task 306:
[ 30.276782] platform_device_release+0x25/0x80
Suggested-by: Nicolas Ferre <Nicolas.Ferre@microchip.com>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea269a6f720782ed94171fb962b14ce07c372138 ]
Currently changes to the advertising state via ethtool do not cause any
reselection of the configured interface mode after the SFP is already
inserted and initially configured.
While it is not typical to change the advertised link modes for an
interface using an SFP in certain use cases it is desirable. In the case
of a SFP port that is capable of handling both SFP and SFP+ modules it
will automatically select between 1G and 10G modes depending on the
supported mode of the SFP. However if the SFP module is capable of
working in multiple modes (e.g. a SFP+ DAC that can operate at 1G or
10G), one end of the cable may be attached to a SFP 1000base-x port thus
the SFP+ end must be manually configured to the 1000base-x mode in order
for the link to be established.
This change causes the ethtool setting of advertised mode changes to
reselect the interface mode so that the link can be established.
Additionally when a module is inserted the advertising mode is reset to
match the supported modes of the module.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7df835a32a8bedf7ce88efcfa7c9b245b52ff139 ]
Commit b0140891a8cea3 ("md: Fix race when creating a new md device.")
not only moved assigning mddev->gendisk before calling add_disk, which
fixes the races described in the commit log, but also added a
mddev->open_mutex critical section over add_disk and creation of the
md kobj. Adding a kobject after add_disk is racy vs deleting the gendisk
right after adding it, but md already prevents against that by holding
a mddev->active reference.
On the other hand taking this lock added a lock order reversal with what
is not disk->open_mutex (used to be bdev->bd_mutex when the commit was
added) for partition devices, which need that lock for the internal open
for the partition scan, and a recent commit also takes it for
non-partitioned devices, leading to further lockdep splatter.
Fixes: b0140891a8ce ("md: Fix race when creating a new md device.")
Fixes: d62633873590 ("block: support delayed holder registration")
Reported-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com
Reviewed-by: NeilBrown <neilb@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 280bef512933b2dda01d681d8cbe499b98fc5bdd ]
In its_vpe_irq_domain_alloc, when its_vpe_init() returns an error,
there is an off-by-one in the number of VPEs to be freed.
Fix it by simply passing the number of VPEs allocated, which is the
index of the loop iterating over the VPEs.
Fixes: 7d75bbb4bc1a ("irqchip/gic-v3-its: Add VPE irq domain allocation/teardown")
Signed-off-by: Kaige Fu <kaige.fu@linux.alibaba.com>
[maz: fixed commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/d9e36dee512e63670287ed9eff884a5d8d6d27f2.1631672311.git.kaige.fu@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 969ac78db78c723a24e9410666b457cc1b0cb3c3 ]
irq-goldfish-pic uses GENERIC_IRQ_CHIP interfaces so select that symbol
to fix build errors.
Fixes these build errors:
mips-linux-ld: drivers/irqchip/irq-goldfish-pic.o: in function `goldfish_pic_of_init':
irq-goldfish-pic.c:(.init.text+0xc0): undefined reference to `irq_alloc_generic_chip'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0xf4): undefined reference to `irq_gc_unmask_enable_reg'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0xf8): undefined reference to `irq_gc_unmask_enable_reg'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0x100): undefined reference to `irq_gc_mask_disable_reg'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0x104): undefined reference to `irq_gc_mask_disable_reg'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0x11c): undefined reference to `irq_setup_generic_chip'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0x168): undefined reference to `irq_remove_generic_chip'
Fixes: 4235ff50cf98 ("irqchip/irq-goldfish-pic: Add Goldfish PIC driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Miodrag Dinic <miodrag.dinic@mips.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Goran Ferenc <goran.ferenc@mips.com>
Cc: Aleksandar Markovic <aleksandar.markovic@mips.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210905162519.21507-1-rdunlap@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6dacc371b77f473770ec646e220303a84fe96c11 ]
The limit should be "PAGE_SIZE - len" instead of "PAGE_SIZE". We're not
going to hit the limit so this fix will not affect runtime.
Link: https://lore.kernel.org/r/20210916132331.GE25094@kili
Fixes: 5b9e70b22cc5 ("scsi: lpfc: raise sg count for nvme to use available sg resources")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f8579038842d77e6ce05e1df6bf9dd493b0e3ef ]
In dual mode in case of disabling the target, the whole port goes offline
and initiator is turned off too.
Fix restoring initiator mode after disabling target in dual mode.
Link: https://lore.kernel.org/r/20210915153239.8035-1-d.bogdanov@yadro.com
Fixes: 0645cb8350cd ("scsi: qla2xxx: Add mode control for each physical port")
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1bb30b20b49773369c299d4d6c65227201328663 ]
After printing the list of thermal governors, then this function prints
a newline character. The problem is that "size" has not been updated
after printing the last governor. This means that it can write one
character (the NUL terminator) beyond the end of the buffer.
Get rid of the "size" variable and just use "PAGE_SIZE - count" directly.
Fixes: 1b4f48494eb2 ("thermal: core: group functions related to governor handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210916131342.GB25094@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 298ba0e3d4af539cc37f982d4c011a0f07fca48c ]
Various places in the nvme code that rely on ctrl->namespace to be
ordered. Ensure that the namespae is inserted into the list at the
right position from the start instead of sorting it after the fact.
Fixes: 540c801c65eb ("NVMe: Implement namespace list scanning")
Reported-by: Anton Eidelman <anton.eidelman@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4f0f586bf0c898233d8f316f471a21db2abd522d ]
list_sort() internally casts the comparison function passed to it
to a different type with constant struct list_head pointers, and
uses this pointer to call the functions, which trips indirect call
Control-Flow Integrity (CFI) checking.
Instead of removing the consts, this change defines the
list_cmp_func_t type and changes the comparison function types of
all list_sort() callers to use const pointers, thus avoiding type
mismatches.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210408182843.1754385-10-samitolvanen@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e371af033c560b9dd1e861f8f0b503142bf0a06c ]
When the controller sends us multiple r2t PDUs in a single
request we need to account for it correctly as our send/recv
context run concurrently (i.e. we get a new r2t with r2t_offset
before we updated our iterator and req->data_sent marker). This
can cause wrong offsets to be sent to the controller.
To fix that, we will first know that this may happen only in
the send sequence of the last page, hence we will take
the r2t_offset to the h2c PDU data_offset, and in
nvme_tcp_try_send_data loop, we make sure to increment
the request markers also when we completed a PDU but
we are expecting more r2t PDUs as we still did not send
the entire data of the request.
Fixes: 825619b09ad3 ("nvme-tcp: fix possible use-after-completion")
Reported-by: Nowak, Lukasz <Lukasz.Nowak@Dell.com>
Tested-by: Nowak, Lukasz <Lukasz.Nowak@Dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a1e4470823d99e75b596748086e120dea169ed3c ]
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'ret'.
Eliminate the follow smatch warning:
drivers/fpga/machxo2-spi.c:341 machxo2_write_complete()
warn: missing error code 'ret'.
[mdf@kernel.org: Reworded commit message]
Fixes: 88fb3a002330 ("fpga: lattice machxo2: Add Lattice MachXO2 support")
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 34331739e19fd6a293d488add28832ad49c9fc54 ]
Earlier successes leave 'ret' in a non error state, so these errors are
not reported. Set ret to -EINVAL before going to the error handler.
This addresses two issues reported by smatch:
drivers/fpga/machxo2-spi.c:229 machxo2_write_init()
warn: missing error code 'ret'
drivers/fpga/machxo2-spi.c:316 machxo2_write_complete()
warn: missing error code 'ret'
[mdf@kernel.org: Reworded commit message]
Fixes: 88fb3a002330 ("fpga: lattice machxo2: Add Lattice MachXO2 support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 06e49073dfba24df4b1073a068631b13a0039c34 ]
'set_signals()' in synclink_gt.c conflicts with an exported symbol
in arch/um/, so change set_signals() to set_gtsignals(). Keep
the function names similar by also changing get_signals() to
get_gtsignals().
../drivers/tty/synclink_gt.c:442:13: error: conflicting types for ‘set_signals’
static void set_signals(struct slgt_info *info);
^~~~~~~~~~~
In file included from ../include/linux/irqflags.h:16:0,
from ../include/linux/spinlock.h:58,
from ../include/linux/mm_types.h:9,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/tty/synclink_gt.c:46:
../arch/um/include/asm/irqflags.h:6:5: note: previous declaration of ‘set_signals’ was here
int set_signals(int enable);
^~~~~~~~~~~
Fixes: 705b6c7b34f2 ("[PATCH] new driver synclink_gt")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210902003806.17054-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b9b90fe655c0bd816847ac1bcbf179cfa2981ecb ]
Forward declarations make the code larger and rewrites harder. Harder as
they are often omitted from global changes. Remove forward declarations
which are not really needed, i.e. the definition of the function is
before its first use.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-39-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ef7ae7f746e95c6fa4ec2bcfacb949c36263da78 ]
Commit 356ba2a8bc8d ("scsi: target: tcmu: Make pgr_support and alua_support
attributes writable") introduced support for changeable alua_support and
pgr_support target attributes. These can only be changed if the backstore
is user-backed, otherwise the kernel returns -EINVAL.
This triggers a warning in the targetcli/rtslib code when performing a
target restore that includes non-userbacked backstores:
# targetctl restore
Storage Object block/storage1: Cannot set attribute alua_support:
[Errno 22] Invalid argument, skipped
Storage Object block/storage1: Cannot set attribute pgr_support:
[Errno 22] Invalid argument, skipped
Fix this warning by returning an error code only if we are really going to
flip the PGR/ALUA bit in the transport_flags field, otherwise we will do
nothing and return success.
Return ENOSYS instead of EINVAL if the pgr/alua attributes can not be
changed, this way it will be possible for userspace to understand if the
operation failed because an invalid value has been passed to strtobool() or
because the attributes are fixed.
Fixes: 356ba2a8bc8d ("scsi: target: tcmu: Make pgr_support and alua_support attributes writable")
Link: https://lore.kernel.org/r/20210906151809.52811-1-mlombard@redhat.com
Reviewed-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e28550829258f7dab97383acaa477bd724c0ff4 ]
ISCSI_NET_PARAM_IFACE_ENABLE belongs to enum iscsi_net_param instead of
iscsi_iface_param so move it to ISCSI_NET_PARAM. Otherwise, when we call
into the driver, we might not match and return that we don't want attr
visible in sysfs. Found in code review.
Link: https://lore.kernel.org/r/20210901085336.2264295-1-libaokun1@huawei.com
Fixes: e746f3451ec7 ("scsi: iscsi: Fix iface sysfs attr detection")
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d88c339c423eefe2fd48215016cb0c75fcb4c4d ]
After fixing hibernation resume flow, another usecase was found which
should be explicitly handled - resume when device is in "down" state.
Invoke aq_nic_init jointly with aq_nic_start only if ndev was already
up during suspend/hibernate. We still need to perform nic_deinit() if
caller requests for it, to handle the freeze/resume scenarios.
Fixes: 57f780f1c433 ("atlantic: Fix driver resume flow.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fdbccea419dc782079ce5881d2705cc9e3881480 ]
Driver doesn't support aRFS for encapsulated packets, return early error
in such a case.
Fixes: 1eb8c695bda9 ("net/mlx4_en: Add accelerated RFS support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
