summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2020-03-11dm cache: fix a crash due to incorrect work item cancellingMikulas Patocka1-2/+2
commit 7cdf6a0aae1cccf5167f3f04ecddcf648b78e289 upstream. The crash can be reproduced by running the lvm2 testsuite test lvconvert-thin-external-cache.sh for several minutes, e.g.: while :; do make check T=shell/lvconvert-thin-external-cache.sh; done The crash happens in this call chain: do_waker -> policy_tick -> smq_tick -> end_hotspot_period -> clear_bitset -> memset -> __memset -- which accesses an invalid pointer in the vmalloc area. The work entry on the workqueue is executed even after the bitmap was freed. The problem is that cancel_delayed_work doesn't wait for the running work item to finish, so the work item can continue running and re-submitting itself even after cache_postsuspend. In order to make sure that the work item won't be running, we must use cancel_delayed_work_sync. Also, change flush_workqueue to drain_workqueue, so that if some work item submits itself or another work item, we are properly waiting for both of them. Fixes: c6b4fcbad044 ("dm: add cache target") Cc: stable@vger.kernel.org # v3.9 Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11dmaengine: coh901318: Fix a double lock bug in dma_tc_handle()Dan Carpenter1-4/+0
commit 36d5d22090d13fd3a7a8c9663a711cbe6970aac8 upstream. The caller is already holding the lock so this will deadlock. Fixes: 0b58828c923e ("DMAENGINE: COH 901 318 remove irq counting") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20200217144050.3i4ymbytogod4ijn@kili.mountain Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11hwmon: (adt7462) Fix an error return in ADT7462_REG_VOLT()Dan Carpenter1-1/+1
commit 44f2f882909fedfc3a56e4b90026910456019743 upstream. This is only called from adt7462_update_device(). The caller expects it to return zero on error. I fixed a similar issue earlier in commit a4bf06d58f21 ("hwmon: (adt7462) ADT7462_REG_VOLT_MAX() should return 0") but I missed this one. Fixes: c0b4e3ab0c76 ("adt7462: new hwmon driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Link: https://lore.kernel.org/r/20200303101608.kqjwfcazu2ylhi2a@kili.mountain Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11RMDA/cm: Fix missing ib_cm_destroy_id() in ib_cm_insert_listen()Jason Gunthorpe1-0/+1
commit c14dfddbd869bf0c2bafb7ef260c41d9cebbcfec upstream. The algorithm pre-allocates a cm_id since allocation cannot be done while holding the cm.lock spinlock, however it doesn't free it on one error path, leading to a memory leak. Fixes: 067b171b8679 ("IB/cm: Share listening CM IDs") Link: https://lore.kernel.org/r/20200221152023.GA8680@ziepe.ca Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11RDMA/iwcm: Fix iwcm work deallocationBernard Metzler1-1/+3
commit 810dbc69087b08fd53e1cdd6c709f385bc2921ad upstream. The dealloc_work_entries() function must update the work_free_list pointer while freeing its entries, since potentially called again on same list. A second iteration of the work list caused system crash. This happens, if work allocation fails during cma_iw_listen() and free_cm_id() tries to free the list again during cleanup. Fixes: 922a8e9fb2e0 ("RDMA: iWARP Connection Manager.") Link: https://lore.kernel.org/r/20200302181614.17042-1-bmt@zurich.ibm.com Reported-by: syzbot+cb0c054eabfba4342146@syzkaller.appspotmail.com Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11dmaengine: tegra-apb: Prevent race conditions of tasklet vs free listDmitry Osipenko1-1/+1
commit c33ee1301c393a241d6424e36eff1071811b1064 upstream. The interrupt handler puts a half-completed DMA descriptor on a free list and then schedules tasklet to process bottom half of the descriptor that executes client's callback, this creates possibility to pick up the busy descriptor from the free list. Thus, let's disallow descriptor's re-use until it is fully processed. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200209163356.6439-3-digetx@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11dmaengine: tegra-apb: Fix use-after-freeDmitry Osipenko1-4/+0
commit 94788af4ed039476ff3527b0e6a12c1dc42cb022 upstream. I was doing some experiments with I2C and noticed that Tegra APB DMA driver crashes sometime after I2C DMA transfer termination. The crash happens because tegra_dma_terminate_all() bails out immediately if pending list is empty, and thus, it doesn't release the half-completed descriptors which are getting re-used before ISR tasklet kicks-in. tegra-i2c 7000c400.i2c: DMA transfer timeout elants_i2c 0-0010: elants_i2c_irq: failed to read data: -110 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 142 at lib/list_debug.c:45 __list_del_entry_valid+0x45/0xac list_del corruption, ddbaac44->next is LIST_POISON1 (00000100) Modules linked in: CPU: 0 PID: 142 Comm: kworker/0:2 Not tainted 5.5.0-rc2-next-20191220-00175-gc3605715758d-dirty #538 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) Workqueue: events_freezable_power_ thermal_zone_device_check [<c010e5c5>] (unwind_backtrace) from [<c010a1c5>] (show_stack+0x11/0x14) [<c010a1c5>] (show_stack) from [<c0973925>] (dump_stack+0x85/0x94) [<c0973925>] (dump_stack) from [<c011f529>] (__warn+0xc1/0xc4) [<c011f529>] (__warn) from [<c011f7e9>] (warn_slowpath_fmt+0x61/0x78) [<c011f7e9>] (warn_slowpath_fmt) from [<c042497d>] (__list_del_entry_valid+0x45/0xac) [<c042497d>] (__list_del_entry_valid) from [<c047a87f>] (tegra_dma_tasklet+0x5b/0x154) [<c047a87f>] (tegra_dma_tasklet) from [<c0124799>] (tasklet_action_common.constprop.0+0x41/0x7c) [<c0124799>] (tasklet_action_common.constprop.0) from [<c01022ab>] (__do_softirq+0xd3/0x2a8) [<c01022ab>] (__do_softirq) from [<c0124683>] (irq_exit+0x7b/0x98) [<c0124683>] (irq_exit) from [<c0168c19>] (__handle_domain_irq+0x45/0x80) [<c0168c19>] (__handle_domain_irq) from [<c043e429>] (gic_handle_irq+0x45/0x7c) [<c043e429>] (gic_handle_irq) from [<c0101aa5>] (__irq_svc+0x65/0x94) Exception stack(0xde2ebb90 to 0xde2ebbd8) Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200209163356.6439-2-digetx@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11vt: selection, push sel_lock upJiri Slaby1-9/+7
commit e8c75a30a23c6ba63f4ef6895cbf41fd42f21aa2 upstream. sel_lock cannot nest in the console lock. Thanks to syzkaller, the kernel states firmly: > WARNING: possible circular locking dependency detected > 5.6.0-rc3-syzkaller #0 Not tainted > ------------------------------------------------------ > syz-executor.4/20336 is trying to acquire lock: > ffff8880a2e952a0 (&tty->termios_rwsem){++++}, at: tty_unthrottle+0x22/0x100 drivers/tty/tty_ioctl.c:136 > > but task is already holding lock: > ffffffff89462e70 (sel_lock){+.+.}, at: paste_selection+0x118/0x470 drivers/tty/vt/selection.c:374 > > which lock already depends on the new lock. > > the existing dependency chain (in reverse order) is: > > -> #2 (sel_lock){+.+.}: > mutex_lock_nested+0x1b/0x30 kernel/locking/mutex.c:1118 > set_selection_kernel+0x3b8/0x18a0 drivers/tty/vt/selection.c:217 > set_selection_user+0x63/0x80 drivers/tty/vt/selection.c:181 > tioclinux+0x103/0x530 drivers/tty/vt/vt.c:3050 > vt_ioctl+0x3f1/0x3a30 drivers/tty/vt/vt_ioctl.c:364 This is ioctl(TIOCL_SETSEL). Locks held on the path: console_lock -> sel_lock > -> #1 (console_lock){+.+.}: > console_lock+0x46/0x70 kernel/printk/printk.c:2289 > con_flush_chars+0x50/0x650 drivers/tty/vt/vt.c:3223 > n_tty_write+0xeae/0x1200 drivers/tty/n_tty.c:2350 > do_tty_write drivers/tty/tty_io.c:962 [inline] > tty_write+0x5a1/0x950 drivers/tty/tty_io.c:1046 This is write(). Locks held on the path: termios_rwsem -> console_lock > -> #0 (&tty->termios_rwsem){++++}: > down_write+0x57/0x140 kernel/locking/rwsem.c:1534 > tty_unthrottle+0x22/0x100 drivers/tty/tty_ioctl.c:136 > mkiss_receive_buf+0x12aa/0x1340 drivers/net/hamradio/mkiss.c:902 > tty_ldisc_receive_buf+0x12f/0x170 drivers/tty/tty_buffer.c:465 > paste_selection+0x346/0x470 drivers/tty/vt/selection.c:389 > tioclinux+0x121/0x530 drivers/tty/vt/vt.c:3055 > vt_ioctl+0x3f1/0x3a30 drivers/tty/vt/vt_ioctl.c:364 This is ioctl(TIOCL_PASTESEL). Locks held on the path: sel_lock -> termios_rwsem > other info that might help us debug this: > > Chain exists of: > &tty->termios_rwsem --> console_lock --> sel_lock Clearly. From the above, we have: console_lock -> sel_lock sel_lock -> termios_rwsem termios_rwsem -> console_lock Fix this by reversing the console_lock -> sel_lock dependency in ioctl(TIOCL_SETSEL). First, lock sel_lock, then console_lock. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: syzbot+26183d9746e62da329b8@syzkaller.appspotmail.com Fixes: 07e6124a1a46 ("vt: selection, close sel_buffer race") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200228115406.5735-2-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11vt: selection, push console lock downJiri Slaby2-3/+12
commit 4b70dd57a15d2f4685ac6e38056bad93e81e982f upstream. We need to nest the console lock in sel_lock, so we have to push it down a bit. Fortunately, the callers of set_selection_* just lock the console lock around the function call. So moving it down is easy. In the next patch, we switch the order. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Fixes: 07e6124a1a46 ("vt: selection, close sel_buffer race") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200228115406.5735-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11vt: selection, close sel_buffer raceJiri Slaby1-6/+17
commit 07e6124a1a46b4b5a9b3cacc0c306b50da87abf5 upstream. syzkaller reported this UAF: BUG: KASAN: use-after-free in n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741 Read of size 1 at addr ffff8880089e40e9 by task syz-executor.1/13184 CPU: 0 PID: 13184 Comm: syz-executor.1 Not tainted 5.4.7 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014 Call Trace: ... kasan_report+0xe/0x20 mm/kasan/common.c:634 n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741 tty_ldisc_receive_buf+0xac/0x190 drivers/tty/tty_buffer.c:461 paste_selection+0x297/0x400 drivers/tty/vt/selection.c:372 tioclinux+0x20d/0x4e0 drivers/tty/vt/vt.c:3044 vt_ioctl+0x1bcf/0x28d0 drivers/tty/vt/vt_ioctl.c:364 tty_ioctl+0x525/0x15a0 drivers/tty/tty_io.c:2657 vfs_ioctl fs/ioctl.c:47 [inline] It is due to a race between parallel paste_selection (TIOCL_PASTESEL) and set_selection_user (TIOCL_SETSEL) invocations. One uses sel_buffer, while the other frees it and reallocates a new one for another selection. Add a mutex to close this race. The mutex takes care properly of sel_buffer and sel_buffer_lth only. The other selection global variables (like sel_start, sel_end, and sel_cons) are protected only in set_selection_user. The other functions need quite some more work to close the races of the variables there. This is going to happen later. This likely fixes (I am unsure as there is no reproducer provided) bug 206361 too. It was marked as CVE-2020-8648. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: syzbot+59997e8d5cbdc486e6f6@syzkaller.appspotmail.com References: https://bugzilla.kernel.org/show_bug.cgi?id=206361 Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200210081131.23572-2-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11tty:serial:mvebu-uart:fix a wrong returntangbin1-1/+1
commit 4a3e208474204e879d22a310b244cb2f39e5b1f8 upstream. in this place, the function should return a negative value and the PTR_ERR already returns a negative,so return -PTR_ERR() is wrong. Signed-off-by: tangbin <tangbin@cmss.chinamobile.com> Cc: stable <stable@vger.kernel.org> Acked-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20200305013823.20976-1-tangbin@cmss.chinamobile.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11vgacon: Fix a UAF in vgacon_invert_regionZhang Xiaoxu1-0/+3
commit 513dc792d6060d5ef572e43852683097a8420f56 upstream. When syzkaller tests, there is a UAF: BUG: KASan: use after free in vgacon_invert_region+0x9d/0x110 at addr ffff880000100000 Read of size 2 by task syz-executor.1/16489 page:ffffea0000004000 count:0 mapcount:-127 mapping: (null) index:0x0 page flags: 0xfffff00000000() page dumped because: kasan: bad access detected CPU: 1 PID: 16489 Comm: syz-executor.1 Not tainted Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014 Call Trace: [<ffffffffb119f309>] dump_stack+0x1e/0x20 [<ffffffffb04af957>] kasan_report+0x577/0x950 [<ffffffffb04ae652>] __asan_load2+0x62/0x80 [<ffffffffb090f26d>] vgacon_invert_region+0x9d/0x110 [<ffffffffb0a39d95>] invert_screen+0xe5/0x470 [<ffffffffb0a21dcb>] set_selection+0x44b/0x12f0 [<ffffffffb0a3bfae>] tioclinux+0xee/0x490 [<ffffffffb0a1d114>] vt_ioctl+0xff4/0x2670 [<ffffffffb0a0089a>] tty_ioctl+0x46a/0x1a10 [<ffffffffb052db3d>] do_vfs_ioctl+0x5bd/0xc40 [<ffffffffb052e2f2>] SyS_ioctl+0x132/0x170 [<ffffffffb11c9b1b>] system_call_fastpath+0x22/0x27 Memory state around the buggy address: ffff8800000fff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8800000fff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff880000100000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff It can be reproduce in the linux mainline by the program: #include <stdio.h> #include <stdlib.h> #include <unistd.h> #include <fcntl.h> #include <sys/types.h> #include <sys/stat.h> #include <sys/ioctl.h> #include <linux/vt.h> struct tiocl_selection { unsigned short xs; /* X start */ unsigned short ys; /* Y start */ unsigned short xe; /* X end */ unsigned short ye; /* Y end */ unsigned short sel_mode; /* selection mode */ }; #define TIOCL_SETSEL 2 struct tiocl { unsigned char type; unsigned char pad; struct tiocl_selection sel; }; int main() { int fd = 0; const char *dev = "/dev/char/4:1"; struct vt_consize v = {0}; struct tiocl tioc = {0}; fd = open(dev, O_RDWR, 0); v.v_rows = 3346; ioctl(fd, VT_RESIZEX, &v); tioc.type = TIOCL_SETSEL; ioctl(fd, TIOCLINUX, &tioc); return 0; } When resize the screen, update the 'vc->vc_size_row' to the new_row_size, but when 'set_origin' in 'vgacon_set_origin', vgacon use 'vga_vram_base' for 'vc_origin' and 'vc_visible_origin', not 'vc_screenbuf'. It maybe smaller than 'vc_screenbuf'. When TIOCLINUX, use the new_row_size to calc the offset, it maybe larger than the vga_vram_size in vgacon driver, then bad access. Also, if set an larger screenbuf firstly, then set an more larger screenbuf, when copy old_origin to new_origin, a bad access may happen. So, If the screen size larger than vga_vram, resize screen should be failed. This alse fix CVE-2020-8649 and CVE-2020-8647. Linus pointed out that overflow checking seems absent. We're saved by the existing bounds checks in vc_do_resize() with rather strict limits: if (cols > VC_RESIZE_MAXCOL || lines > VC_RESIZE_MAXROW) return -EINVAL; Fixes: 0aec4867dca14 ("[PATCH] SVGATextMode fix") Reference: CVE-2020-8647 and CVE-2020-8649 Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com> [danvet: augment commit message to point out overflow safety] Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20200304022429.37738-1-zhangxiaoxu5@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11usb: core: port: do error out if usb_autopm_get_interface() failsEugeniu Rosca1-2/+8
commit 1f8b39bc99a31759e97a0428a5c3f64802c1e61d upstream. Reviewing a fresh portion of coverity defects in USB core (specifically CID 1458999), Alan Stern noted below in [1]: On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote: > A revised search finds line 997 in drivers/usb/core/hub.c and lines > 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any > other directories.) AFAICT all three of these should check the > return value, although a error message in the kernel log probably > isn't needed. Factor out the usb_port_runtime_{resume,suspend}() changes into a standalone patch to allow conflict-free porting on top of stable v3.9+. [1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org Fixes: 971fcd492cebf5 ("usb: add runtime pm support for usb port device") Cc: stable@vger.kernel.org # v3.9+ Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200226175036.14946-3-erosca@de.adit-jv.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11usb: core: hub: do error out if usb_autopm_get_interface() failsEugeniu Rosca1-1/+5
commit 60e3f6e4ac5b0fda43dad01c32e09409ec710045 upstream. Reviewing a fresh portion of coverity defects in USB core (specifically CID 1458999), Alan Stern noted below in [1]: On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote: > A revised search finds line 997 in drivers/usb/core/hub.c and lines > 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any > other directories.) AFAICT all three of these should check the > return value, although a error message in the kernel log probably > isn't needed. Factor out the usb_remove_device() change into a standalone patch to allow conflict-free integration on top of the earliest stable branches. [1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org Fixes: 253e05724f9230 ("USB: add a "remove hardware" sysfs attribute") Cc: stable@vger.kernel.org # v2.6.33+ Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200226175036.14946-2-erosca@de.adit-jv.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11usb: quirks: add NO_LPM quirk for Logitech Screen ShareDan Lazewatsky1-0/+3
commit b96ed52d781a2026d0c0daa5787c6f3d45415862 upstream. LPM on the device appears to cause xHCI host controllers to claim that there isn't enough bandwidth to support additional devices. Signed-off-by: Dan Lazewatsky <dlaz@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com> Link: https://lore.kernel.org/r/20200226143438.1445-1-gustavo.padovan@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11usb: storage: Add quirk for Samsung Fit flashJim Lin1-0/+6
commit 86d92f5465958752481269348d474414dccb1552 upstream. Current driver has 240 (USB2.0) and 2048 (USB3.0) as max_sectors, e.g., /sys/bus/scsi/devices/0:0:0:0/max_sectors If data access times out, driver error handling will issue a port reset. Sometimes Samsung Fit (090C:1000) flash disk will not respond to later Set Address or Get Descriptor command. Adding this quirk to limit max_sectors to 64 sectors to avoid issue occurring. Signed-off-by: Jim Lin <jilin@nvidia.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1583158895-31342-1-git-send-email-jilin@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11s390/cio: cio_ignore_proc_seq_next should increase position indexVasily Averin1-2/+3
[ Upstream commit 8b101a5e14f2161869636ff9cb4907b7749dc0c2 ] if seq_file .next fuction does not change position index, read after some lseek can generate unexpected output. Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283 Link: https://lore.kernel.org/r/d44c53a7-9bc1-15c7-6d4a-0c10cb9dffce@virtuozzo.com Reviewed-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11watchdog: da9062: do not ping the hw during stop()Marco Felsch1-7/+0
[ Upstream commit e9a0e65eda3f78d0b04ec6136c591c000cbc3b76 ] The da9062 hw has a minimum ping cool down phase of at least 200ms. The driver takes that into account by setting the min_hw_heartbeat_ms to 300ms and the core guarantees that the hw limit is observed for the ping() calls. But the core can't guarantee the required minimum ping cool down phase if a stop() command is send immediately after the ping() command. So it is not allowed to ping the watchdog within the stop() command as the driver does. Remove the ping can be done without doubts because the watchdog gets disabled anyway and a (re)start resets the watchdog counter too. Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20200120091729.16256-1-m.felsch@pengutronix.de [groeck: Updated description] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11net: ks8851-ml: Fix 16-bit IO operationMarek Vasut1-2/+2
[ Upstream commit 58292104832fef6cb4a89f736012c0e0724c3442 ] The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that BE[3:0] signals are active high. This contradicts the measurements of the behavior of the actual chip, where these signals behave as active low. For example, to read the CIDER register, the bus must expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11net: ks8851-ml: Fix 16-bit data accessMarek Vasut1-2/+2
[ Upstream commit edacb098ea9c31589276152f09b4439052c0f2b1 ] The packet data written to and read from Micrel KSZ8851-16MLLI must be byte-swapped in 16-bit mode, add this byte-swapping. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11net: ks8851-ml: Remove 8-bit bus accessorsMarek Vasut1-40/+5
[ Upstream commit 69233bba6543a37755158ca3382765387b8078df ] This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown, however the speculation is that this was some sort of attempt to support the 8-bit bus mode. As per the KS8851-16MLL documentation, all two registers accessed via the 8-bit accessors are internally 16-bit registers, so reading them using 16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read outright, as it is already a concatenation of two 8-bit reads of that register. The KS_RXQCR accesses are 8-bit only, however writing the top 8 bits of the register is OK as well, since the driver caches the entire 16-bit register value anyway. Finally, the driver is not used by any hardware in the kernel right now. The only hardware available to me is one with 16-bit bus, so I have no way to test the 8-bit bus mode, however it is unlikely this ever really worked anyway. If the 8-bit bus mode is ever required, it can be easily added by adjusting the 16-bit accessors to do 2 consecutive accesses, which is how this should have been done from the beginning. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11drm/msm/dsi: save pll state before dsi host is powered offHarigovindan P1-0/+5
[ Upstream commit a1028dcfd0dd97884072288d0c8ed7f30399b528 ] Save pll state before dsi host is powered off. Without this change some register values gets resetted. Signed-off-by: Harigovindan P <harigovi@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11drm: msm: Fix return type of dsi_mgr_connector_mode_valid for kCFIJohn Stultz1-1/+1
[ Upstream commit 7fd2dfc3694922eb7ace4801b7208cf9f62ebc7d ] I was hitting kCFI crashes when building with clang, and after some digging finally narrowed it down to the dsi_mgr_connector_mode_valid() function being implemented as returning an int, instead of an enum drm_mode_status. This patch fixes it, and appeases the opaque word of the kCFI gods (seriously, clang inlining everything makes the kCFI backtraces only really rough estimates of where things went wrong). Thanks as always to Sami for his help narrowing this down. Cc: Rob Clark <robdclark@gmail.com> Cc: Sean Paul <sean@poorly.run> Cc: Sami Tolvanen <samitolvanen@google.com> Cc: Todd Kjos <tkjos@google.com> Cc: Alistair Delva <adelva@google.com> Cc: Amit Pundir <amit.pundir@linaro.org> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: freedreno@lists.freedesktop.org Cc: clang-built-linux@googlegroups.com Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11usb: gadget: serial: fix Tx stall after buffer overflowSergey Organov1-1/+3
[ Upstream commit e4bfded56cf39b8d02733c1e6ef546b97961e18a ] Symptom: application opens /dev/ttyGS0 and starts sending (writing) to it while either USB cable is not connected, or nobody listens on the other side of the cable. If driver circular buffer overflows before connection is established, no data will be written to the USB layer until/unless /dev/ttyGS0 is closed and re-opened again by the application (the latter besides having no means of being notified about the event of establishing of the connection.) Fix: on open and/or connect, kick Tx to flush circular buffer data to USB layer. Signed-off-by: Sergey Organov <sorganov@gmail.com> Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11usb: gadget: ffs: ffs_aio_cancel(): Save/restore IRQ flagsLars-Peter Clausen1-2/+3
[ Upstream commit 43d565727a3a6fd24e37c7c2116475106af71806 ] ffs_aio_cancel() can be called from both interrupt and thread context. Make sure that the current IRQ state is saved and restored by using spin_{un,}lock_irq{save,restore}(). Otherwise undefined behavior might occur. Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11usb: gadget: composite: Support more than 500mA MaxPowerJack Pham1-6/+18
[ Upstream commit a2035411fa1d1206cea7d5dfe833e78481844a76 ] USB 3.x SuperSpeed peripherals can draw up to 900mA of VBUS power when in configured state. However, if a configuration wanting to take advantage of this is added with MaxPower greater than 500 (currently possible if using a ConfigFS gadget) the composite driver fails to accommodate this for a couple reasons: - usb_gadget_vbus_draw() when called from set_config() and composite_resume() will be passed the MaxPower value without regard for the current connection speed, resulting in a violation for USB 2.0 since the max is 500mA. - the bMaxPower of the configuration descriptor would be incorrectly encoded, again if the connection speed is only at USB 2.0 or below, likely wrapping around U8_MAX since the 2mA multiplier corresponds to a maximum of 510mA. Fix these by adding checks against the current gadget->speed when the c->MaxPower value is used (set_config() and composite_resume()) and appropriately limit based on whether it is currently at a low-/full-/high- or super-speed connection. Because 900 is not divisible by 8, with the round-up division currently used in encode_bMaxPower() a MaxPower of 900mA will result in an encoded value of 0x71. When a host stack (including Linux and Windows) enumerates this on a single port root hub, it reads this value back and decodes (multiplies by 8) to get 904mA which is strictly greater than 900mA that is typically budgeted for that port, causing it to reject the configuration. Instead, we should be using the round-down behavior of normal integral division so that 900 / 8 -> 0x70 or 896mA to stay within range. And we might as well change it for the high/full/low case as well for consistency. N.B. USB 3.2 Gen N x 2 allows for up to 1500mA but there doesn't seem to be any any peripheral controller supported by Linux that does two lane operation, so for now keeping the clamp at 900 should be fine. Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDEDaniel Golle1-0/+8
[ Upstream commit 87c5cbf71ecbb9e289d60a2df22eb686c70bf196 ] On AR934x this UART is usually not initialized by the bootloader as it is only used as a secondary serial port while the primary UART is a newly introduced NS16550-compatible. In order to make use of the ar933x-uart on AR934x without RTS/CTS hardware flow control, one needs to set the UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this UART is used as primary/console, the bootloader on AR934x typically doesn't set those bits. Setting them explicitely on AR933x should not do any harm, so just set them unconditionally. Tested-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11vhost: Check docket sk_family instead of call getnameEugenio Pérez1-11/+2
[ Upstream commit 42d84c8490f9f0931786f1623191fcab397c3d64 ] Doing so, we save one call to get data we already have in the struct. Also, since there is no guarantee that getname use sockaddr_ll parameter beyond its size, we add a little bit of security here. It should do not do beyond MAX_ADDR_LEN, but syzbot found that ax25_getname writes more (72 bytes, the size of full_sockaddr_ax25, versus 20 + 32 bytes of sockaddr_ll + MAX_ADDR_LEN in syzbot repro). Fixes: 3a4d5c94e9593 ("vhost_net: a kernel-level virtio server") Reported-by: syzbot+f2a62d07a5198c819c7b@syzkaller.appspotmail.com Signed-off-by: Eugenio Pérez <eperezma@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11drivers: net: xgene: Fix the order of the arguments of 'alloc_etherdev_mqs()'Christophe JAILLET1-1/+1
commit 5a44c71ccda60a50073c5d7fe3f694cdfa3ab0c2 upstream. 'alloc_etherdev_mqs()' expects first 'tx', then 'rx'. The semantic here looks reversed. Reorder the arguments passed to 'alloc_etherdev_mqs()' in order to keep the correct semantic. In fact, this is a no-op because both XGENE_NUM_[RT]X_RING are 8. Fixes: 107dec2749fe ("drivers: net: xgene: Add support for multiple queues") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11tuntap: correctly set SOCKWQ_ASYNC_NOSPACEJason Wang1-4/+15
commit 2f3ab6221e4c87960347d65c7cab9bd917d1f637 upstream. When link is down, writes to the device might fail with -EIO. Userspace needs an indication when the status is resolved. As a fix, tun_net_open() attempts to wake up writers - but that is only effective if SOCKWQ_ASYNC_NOSPACE has been set in the past. This is not the case of vhost_net which only poll for EPOLLOUT after it meets errors during sendmsg(). This patch fixes this by making sure SOCKWQ_ASYNC_NOSPACE is set when socket is not writable or device is down to guarantee EPOLLOUT will be raised in either tun_chr_poll() or tun_sock_write_space() after device is up. Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Eric Dumazet <edumazet@google.com> Fixes: 1bd4978a88ac2 ("tun: honor IFF_UP in tun_get_user()") Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
2020-03-11slip: stop double free sl->dev in slip_openyangerkun1-1/+0
After include 3b5a39979daf ("slip: Fix memory leak in slip_open error path") and e58c19124189 ("slip: Fix use-after-free Read in slip_open") with 4.4.y/4.9.y. We will trigger a bug since we can double free sl->dev in slip_open. Actually, we should backport cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.") too since it has delete free_netdev from sl_free_netdev. Fix it by delete free_netdev from slip_open. Signed-off-by: yangerkun <yangerkun@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11net: ena: make ena rxfh support ETH_RSS_HASH_NO_CHANGEArthur Kiyanovski3-0/+16
commit 470793a78ce344bd53d31e0c2d537f71ba957547 upstream. As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing the key or indirection table using ethtool while keeping the same hash function. Also add a function for retrieving the current hash function from the ena-com layer. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Saeed Bshara <saeedb@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11serial: 8250: Check UPF_IRQ_SHARED in advanceAndy Shevchenko2-3/+6
commit 7febbcbc48fc92e3f33863b32ed715ba4aff18c4 upstream. The commit 54e53b2e8081 ("tty: serial: 8250: pass IRQ shared flag to UART ports") nicely explained the problem: ---8<---8<--- On some systems IRQ lines between multiple UARTs might be shared. If so, the irqflags have to be configured accordingly. The reason is: The 8250 port startup code performs IRQ tests *before* the IRQ handler for that particular port is registered. This is performed in serial8250_do_startup(). This function checks whether IRQF_SHARED is configured and only then disables the IRQ line while testing. This test is performed upon each open() of the UART device. Imagine two UARTs share the same IRQ line: On is already opened and the IRQ is active. When the second UART is opened, the IRQ line has to be disabled while performing IRQ tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself cannot be handled, because the corresponding handler isn't registered, yet. That's because the 8250 code uses a chain-handler and invokes the corresponding port's IRQ handling routines himself. Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't disabled while performing tests and the kernel correctly detects a spurious IRQ. So, adding this flag to the DT probe solves the issue. Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the IRQF_SHARED flag can be set unconditionally as well. Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system: |irq 85: nobody cared (try booting with the "irqpoll" option) | [...] |handlers: |[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt |Disabling IRQ #85 ---8<---8<--- But unfortunately didn't fix the root cause. Let's try again here by moving IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup(). This should fix the similar issue reported for 8250_pnp case. Since this change we don't need to have custom solutions in 8250_aspeed_vuart and 8250_of drivers, thus, drop them. Fixes: 1c2f04937b3e ("serial: 8250: add IRQ trigger support") Reported-by: Li RongQing <lirongqing@baidu.com> Cc: Kurt Kanzenbach <kurt@linutronix.de> Cc: Vikram Pandita <vikram.pandita@ti.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable <stable@vger.kernel.org> Acked-by: Kurt Kanzenbach <kurt@linutronix.de> Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com [Kurt: Backport to v4.9] Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11i2c: jz4780: silence log flood on txabrtWolfram Sang1-34/+2
commit 9e661cedcc0a072d91a32cb88e0515ea26e35711 upstream. The printout for txabrt is way too talkative and is highly annoying with scanning programs like 'i2cdetect'. Reduce it to the minimum, the rest can be gained by I2C core debugging and datasheet information. Also, make it a debug printout, it won't help the regular user. Fixes: ba92222ed63a ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780") Reported-by: H. Nikolaus Schaller <hns@goldelico.com> Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11HID: hiddev: Fix race in in hiddev_disconnect()dan.carpenter@oracle.com1-1/+1
commit 5c02c447eaeda29d3da121a2e17b97ccaf579b51 upstream. Syzbot reports that "hiddev" is used after it's free in hiddev_disconnect(). The hiddev_disconnect() function sets "hiddev->exist = 0;" so hiddev_release() can free it as soon as we drop the "existancelock" lock. This patch moves the mutex_unlock(&hiddev->existancelock) until after we have finished using it. Reported-by: syzbot+784ccb935f9900cc7c9e@syzkaller.appspotmail.com Fixes: 7f77897ef2b6 ("HID: hiddev: fix potential use-after-free") Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11HID: core: fix off-by-one memset in hid_report_raw_event()Johan Korsnes1-1/+3
commit 5ebdffd25098898aff1249ae2f7dbfddd76d8f8f upstream. In case a report is greater than HID_MAX_BUFFER_SIZE, it is truncated, but the report-number byte is not correctly handled. This results in a off-by-one in the following memset, causing a kernel Oops and ensuing system crash. Note: With commit 8ec321e96e05 ("HID: Fix slab-out-of-bounds read in hid_field_extract") I no longer hit the kernel Oops as we instead fail "controlled" at probe if there is a report too long in the HID report-descriptor. hid_report_raw_event() is an exported symbol, so presumabely we cannot always rely on this being the case. Fixes: 966922f26c7f ("HID: fix a crash in hid_report_raw_event() function.") Signed-off-by: Johan Korsnes <jkorsnes@cisco.com> Cc: Armando Visconti <armando.visconti@st.com> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11ACPI: watchdog: Fix gas->access_width usageMika Westerberg2-3/+2
commit 2ba33a4e9e22ac4dda928d3e9b5978a3a2ded4e0 upstream. ACPI Generic Address Structure (GAS) access_width field is not in bytes as the driver seems to expect in few places so fix this by using the newly introduced macro ACPI_ACCESS_BYTE_WIDTH(). Fixes: b1abf6fc4982 ("ACPI / watchdog: Fix off-by-one error at resource assignment") Fixes: 058dfc767008 ("ACPI / watchdog: Add support for WDAT hardware watchdog") Reported-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Cc: 4.16+ <stable@vger.kernel.org> # 4.16+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11nfc: pn544: Fix occasional HW initialization failureDmitry Osipenko1-0/+1
[ Upstream commit c3331d2fe3fd4d5e321f2467d01f72de7edfb5d0 ] The PN544 driver checks the "enable" polarity during of driver's probe and it's doing that by turning ON and OFF NFC with different polarities until enabling succeeds. It takes some time for the hardware to power-down, and thus, to deassert the IRQ that is raised by turning ON the hardware. Since the delay after last power-down of the polarity-checking process is missed in the code, the interrupt may trigger immediately after installing the IRQ handler (right after the checking is done), which results in IRQ handler trying to touch the disabled HW and ends with marking NFC as 'DEAD' during of the driver's probe: pn544_hci_i2c 1-002a: NFC: nfc_en polarity : active high pn544_hci_i2c 1-002a: NFC: invalid len byte shdlc: llc_shdlc_recv_frame: NULL Frame -> link is dead This patch fixes the occasional NFC initialization failure on Nexus 7 device. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11net: phy: restore mdio regs in the iproc mdio driverArun Parameswaran1-0/+20
commit 6f08e98d62799e53c89dbf2c9a49d77e20ca648c upstream. The mii management register in iproc mdio block does not have a retention register so it is lost on suspend. Save and restore value of register while resuming from suspend. Fixes: bb1a619735b4 ("net: phy: Initialize mdio clock at probe function") Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11sysrq: Remove duplicated sysrq messagePetr Mladek1-4/+3
commit c3fee60908db4a8594f2e4a2131998384b8fa006 upstream. The commit 97f5f0cd8cd0a0544 ("Input: implement SysRq as a separate input handler") added pr_fmt() definition. It caused a duplicated message prefix in the sysrq header messages, for example: [ 177.053931] sysrq: SysRq : Show backtrace of all active CPUs [ 742.864776] sysrq: SysRq : HELP : loglevel(0-9) reboot(b) crash(c) Fixes: 97f5f0cd8cd0a05 ("Input: implement SysRq as a separate input handler") Signed-off-by: Petr Mladek <pmladek@suse.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11sysrq: Restore original console_loglevel when sysrq disabledPetr Mladek1-0/+1
commit 075e1a0c50f59ea210561d0d0fedbd945615df78 upstream. The sysrq header line is printed with an increased loglevel to provide users some positive feedback. The original loglevel is not restored when the sysrq operation is disabled. This bug was introduced in 2.6.12 (pre-git-history) by the commit ("Allow admin to enable only some of the Magic-Sysrq functions"). Signed-off-by: Petr Mladek <pmladek@suse.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11net: ena: ena-com.c: prevent NULL pointer dereferenceArthur Kiyanovski1-0/+5
[ Upstream commit c207979f5ae10ed70aff1bb13f39f0736973de99 ] comp_ctx can be NULL in a very rare case when an admin command is executed during the execution of ena_remove(). The bug scenario is as follows: * ena_destroy_device() sets the comp_ctx to be NULL * An admin command is executed before executing unregister_netdev(), this can still happen because our device can still receive callbacks from the netdev infrastructure such as ethtool commands. * When attempting to access the comp_ctx, the bug occurs since it's set to NULL Fix: Added a check that comp_ctx is not NULL Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11net: ena: fix incorrectly saving queue numbers when setting RSS indirection ↵Arthur Kiyanovski2-1/+25
table [ Upstream commit 92569fd27f5cb0ccbdf7c7d70044b690e89a0277 ] The indirection table has the indices of the Rx queues. When we store it during set indirection operation, we convert the indices to our internal representation of the indices. Our internal representation of the indices is: even indices for Tx and uneven indices for Rx, where every Tx/Rx pair are in a consecutive order starting from 0. For example if the driver has 3 queues (3 for Tx and 3 for Rx) then the indices are as follows: 0 1 2 3 4 5 Tx Rx Tx Rx Tx Rx The BUG: The issue is that when we satisfy a get request for the indirection table, we don't convert the indices back to the original representation. The FIX: Simply apply the inverse function for the indices of the indirection table after we set it. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11net: ena: rss: store hash function as values and not bitsArthur Kiyanovski1-1/+5
[ Upstream commit 4844470d472d660c26149ad764da2406adb13423 ] The device receives, stores and retrieves the hash function value as bits and not as their enum value. The bug: * In ena_com_set_hash_function() we set cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func. (1 << rss->hash_func) * In ena_com_get_hash_function() we retrieve the hash function and store it's bit value in rss->hash_func. (Now the bit value of rss->hash_func is stored in rss->hash_func instead of it's enum value) The fix: This commit fixes the issue by converting the retrieved hash function values from the device to the matching enum value of the set bit using ffs(). ffs() finds the first set bit's index in a word. Since the function returns 1 for the LSB's index, we need to subtract 1 from the returned value (note that BIT(0) is 1). Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11net: ena: rss: fix failure to get indirection tableSameeh Jubran1-0/+14
[ Upstream commit 0c8923c0a64fb5d14bebb9a9065d2dc25ac5e600 ] On old hardware, getting / setting the hash function is not supported while gettting / setting the indirection table is. This commit enables us to still show the indirection table on older hardwares by setting the hash function and key to NULL. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11net: ena: fix incorrect default RSS keyArthur Kiyanovski2-0/+16
[ Upstream commit 0d1c3de7b8c78a5e44b74b62ede4a63629f5d811 ] Bug description: When running "ethtool -x <if_name>" the key shows up as all zeros. When we use "ethtool -X <if_name> hfunc toeplitz hkey <some:random:key>" to set the key and then try to retrieve it using "ethtool -x <if_name>" then we return the correct key because we return the one we saved. Bug cause: We don't fetch the key from the device but instead return the key that we have saved internally which is by default set to zero upon allocation. Fix: This commit fixes the issue by initializing the key to a random value using netdev_rss_key_fill(). Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11net: ena: add missing ethtool TX timestamping indicationArthur Kiyanovski1-0/+1
[ Upstream commit cf6d17fde93bdda23c9b02dd5906a12bf8c55209 ] Current implementation of the driver calls skb_tx_timestamp()to add a software tx timestamp to the skb, however the software-transmit capability is not reported in ethtool -T. This commit updates the ethtool structure to report the software-transmit capability in ethtool -T using the standard ethtool_op_get_ts_info(). This function reports all software timestamping capabilities (tx and rx), as well as setting phc_index = -1. phc_index is the index of the PTP hardware clock device that will be used for hardware timestamps. Since we don't have such a device in ENA, using the default -1 value is the correct setting. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11net: ena: fix potential crash when rxfh key is NULLArthur Kiyanovski1-8/+9
[ Upstream commit 91a65b7d3ed8450f31ab717a65dcb5f9ceb5ab02 ] When ethtool -X is called without an hkey, ena_com_fill_hash_function() is called with key=NULL, which is passed to memcpy causing a crash. This commit fixes this issue by checking key is not NULL. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11qmi_wwan: re-add DW5821e pre-production variantBjørn Mork1-0/+1
[ Upstream commit 88bf54603f6f2c137dfee1abf6436ceac3528d2d ] Commit f25e1392fdb5 removed the support for the pre-production variant of the Dell DW5821e to avoid probing another USB interface unnecessarily. However, the pre-production samples are found in the wild, and this lack of support is causing problems for users of such samples. It is therefore necessary to support both variants. Matching on both interfaces 0 and 1 is not expected to cause any problem with either variant, as only the QMI function will be probed successfully on either. Interface 1 will be rejected based on the HID class for the production variant: T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2 P: Vendor=413c ProdID=81d7 Rev=03.18 S: Manufacturer=DELL S: Product=DW5821e Snapdragon X20 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option And interface 0 will be rejected based on too few endpoints for the pre-production variant: T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2 P: Vendor=413c ProdID=81d7 Rev= 3.18 S: Manufacturer=DELL S: Product=DW5821e Snapdragon X20 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver= I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Fixes: f25e1392fdb5 ("qmi_wwan: fix interface number for DW5821e production firmware") Link: https://whrl.pl/Rf0vNk Reported-by: Lars Melin <larsm17@gmail.com> Cc: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11drm/msm: Set dma maximum segment size for mdssSean Paul1-0/+8
[ Upstream commit db735fc4036bbe1fbe606819b5f0ff26cc76cdff ] Turning on CONFIG_DMA_API_DEBUG_SG results in the following error: [ 12.078665] msm ae00000.mdss: DMA-API: mapping sg segment longer than device claims to support [len=3526656] [max=65536] [ 12.089870] WARNING: CPU: 6 PID: 334 at /mnt/host/source/src/third_party/kernel/v4.19/kernel/dma/debug.c:1301 debug_dma_map_sg+0x1dc/0x318 [ 12.102655] Modules linked in: joydev [ 12.106442] CPU: 6 PID: 334 Comm: frecon Not tainted 4.19.0 #2 [ 12.112450] Hardware name: Google Cheza (rev3+) (DT) [ 12.117566] pstate: 60400009 (nZCv daif +PAN -UAO) [ 12.122506] pc : debug_dma_map_sg+0x1dc/0x318 [ 12.126995] lr : debug_dma_map_sg+0x1dc/0x318 [ 12.131487] sp : ffffff800cc3ba80 [ 12.134913] x29: ffffff800cc3ba80 x28: 0000000000000000 [ 12.140395] x27: 0000000000000004 x26: 0000000000000004 [ 12.145868] x25: ffffff8008e55b18 x24: 0000000000000000 [ 12.151337] x23: 00000000ffffffff x22: ffffff800921c000 [ 12.156809] x21: ffffffc0fa75b080 x20: ffffffc0f7195090 [ 12.162280] x19: ffffffc0f1c53280 x18: 0000000000000000 [ 12.167749] x17: 0000000000000000 x16: 0000000000000000 [ 12.173218] x15: 0000000000000000 x14: 0720072007200720 [ 12.178689] x13: 0720072007200720 x12: 0720072007200720 [ 12.184161] x11: 0720072007200720 x10: 0720072007200720 [ 12.189641] x9 : ffffffc0f1fc6b60 x8 : 0000000000000000 [ 12.195110] x7 : ffffff8008132ce0 x6 : 0000000000000000 [ 12.200585] x5 : 0000000000000000 x4 : ffffff8008134734 [ 12.206058] x3 : ffffff800cc3b830 x2 : ffffffc0f1fc6240 [ 12.211532] x1 : 25045a74f48a7400 x0 : 25045a74f48a7400 [ 12.217006] Call trace: [ 12.219535] debug_dma_map_sg+0x1dc/0x318 [ 12.223671] get_pages+0x19c/0x20c [ 12.227177] msm_gem_fault+0x64/0xfc [ 12.230874] __do_fault+0x3c/0x140 [ 12.234383] __handle_mm_fault+0x70c/0xdb8 [ 12.238603] handle_mm_fault+0xac/0xc4 [ 12.242473] do_page_fault+0x1bc/0x3d4 [ 12.246342] do_translation_fault+0x54/0x88 [ 12.250652] do_mem_abort+0x60/0xf0 [ 12.254250] el0_da+0x20/0x24 [ 12.257317] irq event stamp: 67260 [ 12.260828] hardirqs last enabled at (67259): [<ffffff8008132d0c>] console_unlock+0x214/0x608 [ 12.269693] hardirqs last disabled at (67260): [<ffffff8008080e0c>] do_debug_exception+0x5c/0x178 [ 12.278820] softirqs last enabled at (67256): [<ffffff8008081664>] __do_softirq+0x4d4/0x520 [ 12.287510] softirqs last disabled at (67249): [<ffffff80080be574>] irq_exit+0xa8/0x100 [ 12.295742] ---[ end trace e63cfc40c313ffab ]--- The root of the problem is that the default segment size for sgt is (UINT_MAX & PAGE_MASK), and the default segment size for device dma is 64K. As such, if you compare the 2, you would deduce that the sg segment will overflow the device's capacity. In reality, the hardware can accommodate the larger sg segments, it's just not initializing its max segment properly. This patch initializes the max segment size for the mdss device, which gets rid of that pesky warning. Reported-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200121111813.REPOST.1.I92c66a35fb13f368095b05287bdabdbe88ca6922@changeid Signed-off-by: Sasha Levin <sashal@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-28 13:37:33 +0300