| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
To support device specific attributes, new common driver function is added.
Eventually those are created on registering the sysfs with common dev attrs.
Furthermore, this patch makes adding device attributes simple in each driver.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LP55xx common driver provides generic firmware interface
for running a LED pattern.
LP5521 and LP5523 have many device attributes for running patterns.
This patch cleans up those complex code.
Removed device attributes:
engine1_mode
engine2_mode
engine3_mode
engine1_load
engine2_load
engine3_load
engine1_leds
engine2_leds
engine3_leds
All device attributes and functions are replaced with two callback functions,
'firmware_cb' and 'run_engine'.
New engine functions:
lp5523_load/stop/run_engine(), lp5523_update_program_memory() and
lp5523_wait_opmode_done()
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LP55xx common driver provides generic firmware interface
for running a LED pattern.
LP5521 and LP5523 have many device attributes for running patterns.
This patch cleans up those complex code.
Removed device attributes:
engine1_mode
engine2_mode
engine3_mode
engine1_load
engine2_load
engine3_load
led_pattern
All device attributes and functions are replaced with two callback functions,
'firmware_cb' and 'run_engine'.
New engine functions:
lp5521_load/stop/run_engine(), lp5521_update_program_memory() and
lp5521_wait_opmode_done()
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch provides additional device attributes which enable
loading the firmware. ('select_engine' and 'run_engine')
To run a LED pattern, two parts of driver should be enabled.
Common features : lp55xx-common
===============================
Firmware interface for loading LED patterns
Chip specific features : leds-lp5521, leds-lp5523
=================================================
Register addresses for loading firmware data
Register addresses for running selected engine
Pattern programming sequence
============================
LP55xx chips have three program engines.
To load and run a LED pattern, the programming sequence is as follows.
(1) Select an engine number (1/2/3)
(2) Set engine mode to load
(3) Write pattern data into selected area
(4) Set engine mode to run
This sequence is almost same as the firmware interface.
(1) Select an engine number : 'select_engine' dev attribute
(2) Mode change to load : 'loading' of firmware class
(3) Write pattern data into selected area : 'data' of firmware class
(4) Mode change to run : 'run_engine' dev attribute
(1) and (4) are device specific features which provide callback functions
(2) and (3) are common features.
For example,
echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
echo 1 > /sys/class/firmware/lp5521/loading
echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
echo 0 > /sys/class/firmware/lp5521/loading
echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
As soon as 'loading' is set to 0, registered callback is called.
Inside the callback, the selected engine is loaded and memory is updated.
To run programmed pattern, 'run_engine' attribute should be enabled.
Device specific data structure
==============================
o Firmware callback
load selected engine and update program memory
o Run engine
change the engine mode
o 'engine_idx' and firmware data, 'fw'
Those are used in the driver internally with callback functions
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LP55xx family chips have internal program memory which run various patterns.
Using this memory, LEDs continue on blinking/dimming without continuous I2C
commands. That means the I2C HOST can be entered into sleep once the memory
is updated.
An application can get hex data from a file and write them into
the program memory through the I2C. This is general firwmare interface.
This patch is the initial step for adding the firmware interface.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Use lp55xx_unregister_leds() rather than duplicate code.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
To unregister led class devices and sysfs attributes,
LP5521 and LP5523 have each driver function.
This patch makes both drivers simple using common driver function,
lp55xx_unregister_leds().
And some unused variables are removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LED current is configurable via the sysfs.
Max current is a read-only attribute.
These attributes code can be shared in lp55xx common driver.
Device attributes: 'led_current' and 'max_current'
move to lp55xx common driver
Replaced functions:
show_max_current() => lp55xx_show_max_current()
show_current() => lp55xx_show_current()
store_current() => lp55xx_store_current()
LED setting function: set_led_current()
Current registers are device specific, so configurable function is added
in each driver.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
lp5521_set_brightness() and lp5523_set_brightness() are replaced with
common function, lp55xx_set_brightness().
This function is invoked when the brightness of each LED channel is updated.
LP5521 and LP5523 have different register address for the brightness control,
so this work is done by chip specific brightness_work_fn().
lp5521/5523_led_brightness_work():
use lp55xx_led and lp55xx_chip data structure.
use lp55xx write function.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
lp5521_init_led() and lp5523_init_led() are replaced with one common function,
lp55xx_init_led().
Max channels is configurable, so it's used in lp55xx_init_led().
'LP5523_LEDS' are changed to 'LP5523_MAX_LEDS'.
lp55xx_set_brightness, lp55xx_led_attributes: skeleton
Will be filled in next patches.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LED class devices are registered in lp5521_register_leds() and
lp5523_register_leds().
Two separate functions are merged into consolidated lp55xx function,
lp55xx_register_leds().
Error handling fix:
Unregistering LEDS are handled in lp55xx_register_leds() when LED registration
failure occurs. So each driver error handler is changed to 'err_register_leds'
Chip dependency: 'brightness_work_fn' and 'set_led_current'
To make the structure abstract, both functions are configured in each driver.
Those functions should be done by each driver because register control is
chip-dependant work.
lp55xx_init_led: skeleton
Will be filled in next patch
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Two separate de-init functions are merged into one common function.
And it is used in err_post_init of lp55xx_init_device().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
lp5521/5523_init_device() are replaced with lp55xx common function,
lp55xx_init_device().
Error handler in init_device:
deinit function are matched with 'err_post_init' section in
lp55xx_init_device().
Remove LP5523 engine intialization code:
Engine functionality is not mandatory but optional.
Moreover engine initialization is done internally with device reset command.
Therefore, this code is unnecessary.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LP5521/5523 chip configuration is replaced with lp55xx common function,
lp55xx_post_init_device().
Name change:
lp5521/5523_configure() to lp5521/5523_post_init_device()
These are called in init function.
Register access function
Argument type is changed from 'i2c_client' to 'lp55xx_chip'.
Use exported R/W functions of lp55xx common driver.
Temporary variables in lp5521/5523_init_device()
These functions will be removed but temporary variables are needed for
blocking build warnings - incompatible pointer.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LP5521/5523 chip detection functions are replaced with lp55xx common function,
lp55xx_detect_device().
Chip dependent address and values are configurable in each driver.
In init function, chip detection is executed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LP5521/5523 reset device functions are moved to lp55xx common driver.
Value of register address and value are chip dependent.
Those are configured in each driver.
In init function, reset command is executed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LP5521/5523 platform data functions are moved to lp55xx common driver.
New init function, lp55xx_init_device() is created.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch is a preceding step for making common lp55xx init function.
Return code:
Do not use 'OR' arithmetic for the result.
If some error occurs, just return it.
Remove engine verification code:
To check whether internal engine works or not, many lines of code are executed.
However, this job is unnecessary during the chip initialization because
the engine usage is not mandatory but optional function.
LED engines are enabled when specific LED pattern is loaded.
Therefore, this verification code is removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch is a preceding step for making common lp55xx init function.
LP5521_REG_R_CURRENT register code moved:
Chip specific code moved from lp5521_init_device() to lp5521_configure().
Remove engine init function:
LP5521 has internal program engines which are used for running LED patterns.
(blinking, ramp up/down and other emotional visual effects)
Engine initialization is done by reset command in lp5521_init_device().
Remove this duplicate code.
Return code:
Do not use 'OR' arithmetic for the result.
If some error occus, just return it.
Enable latency:
Use explicit named function, lp5521_wait_enable_done().
According to the datasheet, 500us is guaranteed time.
Thus wait time is changed from 1000us to 500us.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LP5521 and LP5523 data structures have common features.
Use common lp55xx data structures rather than chip specific data.
Legacy code in probe is replaced with this new data structures.
lp55xx_chip : Common data between lp5521_chip and lp5523_chip
lp55xx_led : Common LED structure between lp5521_led and lp5523_led
lp55xx_platform_data : Common platform data between lp5521_platform_data and
lp5523_platform_data
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Change the name of chip data structure and platform data.
This patch is a preceding step for cleaning up lp5521/5523 probe and remove.
These data will be replaced with new lp55xx common data structures
in next patch.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch supports basic common driver code for LP5521, LP5523/55231 devices.
( Driver Structure Data )
lp55xx_led and lp55xx_chip
In lp55xx common driver, two different data structure is used.
o lp55xx_led
control multi output LED channels such as led current, channel index.
o lp55xx_chip
general chip control such like the I2C and platform data.
For example, LP5521 has maximum 3 LED channels.
LP5523/55231 has 9 output channels.
lp55xx_chip for LP5521 ... lp55xx_led #1
lp55xx_led #2
lp55xx_led #3
lp55xx_chip for LP5523 ... lp55xx_led #1
lp55xx_led #2
.
.
lp55xx_led #9
( Platform Data )
LP5521 and LP5523/55231 have own specific platform data.
However, this data can be handled with just one platform data structure.
The lp55xx platform data is declared in the header.
This structure is derived from leds-lp5521.h and leds-lp5523.h
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Chip specific function is configured when the device is initialized.
So _configure() is moved to each device init function.
If chip configuration gets failed, the device is de-initialized in
each _init_device(), not probe().
For compile error fix, function type declarations are added.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Use explicit each driver function rather than raw command.
These function will be merged into the lp55xx common driver.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
To make LED unregistration code simple, new function, _unregister_leds()
is added in each driver.
This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
To make LED initialization code simple, new function, _register_leds()
is added at each driver.
This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Device de-initialization code is moved to _deinit_device() at each driver.
This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
To make _probe() simple, device initialization code is moved to
_init_device() at each driver.
This patch is a preceding step for lp55xx common driver architecture.
leds-lp5521:
When 'lp5521_init_device()' gets failed, error handling should be 'fail1'
rather than 'fail2'.
fail1: releasing platform resource and return code
fail2: releasing allocated LED devices with handling 'fail1'
The 'lp5521_init_device()' is called before creating LED devices.
Thus, 'goto fail1' is proper error handler of this function.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Fixed the checkpatch warning as below:
WARNING: static const char * array should probably be static const char * const
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This macro is used to create a struct pci_device_id array.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Fixed the checkpatch warning as below:
WARNING: suspect code indent for conditional statements (8, 8)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Fixed the checkpatch warning as below:
WARNING: Avoid CamelCase: <devAttr>
Rename devAttr to attr.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Fixed the checkpatch warning as below:
WARNING: Avoid CamelCase: <devAttr>
Rename devAttr to attr.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
I spent a few minutes to understand why the code catching the mismatch case
by checking if k is 0 or not. And the code using "k - 1" as array index is
unusual.
This patch checks acceptable rate from the lowest rate, and then we don't need
to subtract k by 1. This change improves the readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
fails
Add lm3530_led_enable() and lm3530_led_disable() helper functions.
This ensures setting drvdata->enable to correct status if regulator_disable
fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The lp8788-keyled is a platform driver of lp8788-mfd. The platform
device is allocated when mfd_add_devices() is called in lp8788-mfd.
On the other hand, 'lp->dev' is the i2c client device.
Therefore, this 'platform_device' is a proper parent device in case
of resource managed mem alloc, registering led device and device
kernel messages.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The DT binding for the pwm-leds devices are similar to the gpio-leds type.
LEDs are represented as sub-nodes of the pwm-leds device.
The code for handling the DT boot is based on the code found in the
leds-gpio driver and adapted to use PWMs instead of GPIOs.
To avoid having custom cleanup code in case of DT boot the newly created
devm_of_pwm_get() API is used to get the correct PWM instance.
For usage see:
Documentation/devicetree/bindings/leds/leds-pwm.txt
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The code looks more nicer if we use:
while (i--)
instead:
if (i > 0)
for (i = i - 1; i >= 0; i--)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
When booted with DT users can use devm version of of_pwm_get() to benefit
from automatic resource release.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Allow client driver to use of_pwm_get() to get the PWM they need. This
is needed for drivers which handle more than one PWM separately, like
leds-pwm driver, which have:
pwmleds {
compatible = "pwm-leds";
kpad {
label = "omap4::keypad";
pwms = <&twl_pwm 0 7812500>;
max-brightness = <127>;
};
charging {
label = "omap4:green:chrg";
pwms = <&twl_pwmled 0 7812500>;
max-brightness = <255>;
};
};
in the dts files.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
In order to be able to add device tree support for leds-pwm driver we need
to rearrange the data structures used by the drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Update the driver to use the new API for requesting pwm so we can take
advantage of the pwm_lookup table to find the correct pwm to be used for the
LED functionality.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Support added only for leds (not for gpio's).
(cooloney@gmail.com: fix 2 building errors)
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull more device-mapper fixes from Alasdair G Kergon:
"A fix for stacked dm thin devices and a fix for the new dm WRITE SAME
support."
* tag 'dm-3.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: fix write same requests counting
dm thin: fix queue limits stacking
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
PullHID fixes from Jiri Kosina:
- fix i2c-hid and hidraw interaction, by Benjamin Tissoires
- a quirk to make a particular device (Formosa IR receiver) work
properly, by Nicholas Santos
* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: fix i2c_hid_output_raw_report
HID: usbhid: quirk for Formosa IR receiver
HID: remove x bit from sensor doc
|
|
i2c_hid_output_raw_report is used by hidraw to forward set_report requests.
The current implementation of i2c_hid_set_report needs to take the
report_id as an argument. The report_id is stored in the first byte
of the buffer in argument of i2c_hid_output_raw_report.
Not removing the report_id from the given buffer adds this byte 2 times
in the command, leading to a non working command.
Reported-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When processing write same requests, fix dm to send the configured
number of WRITE SAME requests to the target rather than the number of
discards, which is not always the same.
Device-mapper WRITE SAME support was introduced by commit
23508a96cd2e857d57044a2ed7d305f2d9daf441 ("dm: add WRITE SAME support").
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
|
|
thin_io_hints() is blindly copying the queue limits from the thin-pool
which can lead to incorrect limits being set. The fix here simply
deletes the thin_io_hints() hook which leaves the existing stacking
infrastructure to set the limits correctly.
When a thin-pool uses an MD device for the data device a thin device
from the thin-pool must respect MD's constraints about disallowing a bio
from spanning multiple chunks. Otherwise we can see problems. If the raid0
chunksize is 1152K and thin-pool chunksize is 256K I see the following
md/raid0 error (with extra debug tracing added to thin_endio) when
mkfs.xfs is executed against the thin device:
md/raid0:md99: make_request bug: can't convert block across chunks or bigger than 1152k 6688 127
device-mapper: thin: bio sector=2080 err=-5 bi_size=130560 bi_rw=17 bi_vcnt=32 bi_idx=0
This extra DM debugging shows that the failing bio is spanning across
the first and second logical 1152K chunk (sector 2080 + 255 takes the
bio beyond the first chunk's boundary of sector 2304). So the bio
splitting that DM is doing clearly isn't respecting the MD limits.
max_hw_sectors_kb is 127 for both the thin-pool and thin device
(queue_max_hw_sectors returns 255 so we'll excuse sysfs's lack of
precision). So this explains why bi_size is 130560.
But the thin device's max_hw_sectors_kb should be 4 (PAGE_SIZE) given
that it doesn't have a .merge function (for bio_add_page to consult
indirectly via dm_merge_bvec) yet the thin-pool does sit above an MD
device that has a compulsory merge_bvec_fn. This scenario is exactly
why DM must resort to sending single PAGE_SIZE bios to the underlying
layer. Some additional context for this is available in the header for
commit 8cbeb67a ("dm: avoid unsupported spanning of md stripe boundaries").
Long story short, the reason a thin device doesn't properly get
configured to have a max_hw_sectors_kb of 4 (PAGE_SIZE) is that
thin_io_hints() is blindly copying the queue limits from the thin-pool
device directly to the thin device's queue limits.
Fix this by eliminating thin_io_hints. Doing so is safe because the
block layer's queue limits stacking already enables the upper level thin
device to inherit the thin-pool device's discard and minimum_io_size and
optimal_io_size limits that get set in pool_io_hints. But avoiding the
queue limits copy allows the thin and thin-pool limits to be different
where it is important, namely max_hw_sectors_kb.
Reported-by: Daniel Browning <db@kavod.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
|
