| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The flow control thresholds, i.e. high and low watermarks of the Rx
FIFO for when the hardware should transmit PAUSE frames (XON and XOFF,
respectively), need to be tuned for more efficient use of the FIFO.
The logic to set the thresholds for parts that support early-receive
(ERT) was also wrong in that it should check whether jumbo frames are
in use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During reset, the driver was attempting to disable the Smart Powerdown
feature even if the part does not support Smart Powerdown. Check for
support before attempting to disable the feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CRC stripping should be enabled by default but was not if it was not
specified as a module parameter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/forcedeth.c
|
|
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default the driver opens 8 TX queues (defined by MLX4_EN_NUM_TX_RINGS).
If the driver is configured to support Per Priority Flow Control, we open
8 additional TX rings.
dev->real_num_tx_queues is always set to be MLX4_EN_NUM_TX_RINGS.
The mlx4_en_select_queue() function uses standard hashing (skb_tx_hash)
in case that PPFC is not supported or the skb contain a vlan tag,
otherwise the queue is selected according to vlan priority.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupt moderation should not depend on number of incoming
bytes, but on number of incoming packets.
The previous scheme caused very high interrupts rate for small
messages when big MTU was configured.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the initialization of one of the ports failed,
there is no need to fail the other one as well.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
en_params.c file now only handles Ethtool functionality
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For each debug message, the message will show interface name in case
that the net device was registered, and PCI bus ID with port number
if we were not registered yet. Messages that are not port/netdev specific
stayed in the old format
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.
The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy
powered on is the safest default behavior. Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Network device TX is never run in IRQ context, and skb is freed outside
of the IRQ-disabling spin lock. So checking for IRQ was a waste of time
here.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Slight refactoring of duplicated wait for idle checks
Spelling fix
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: jie.yang@atheros.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several EISA device IDs for 3c509 family network cards are missing from
the driver, making the cards unusable in their EISA mode. Here's a fix to
add them based on the EISA configuration files distributed by 3Com and our
eisa.ids database.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not be stopping the subqueues in cpmac_end_xmit
but rather test the status of them. Replace the calls to
netif_subqueue_stop by __netif_subqueue_stopped. This
fixes an unrecoverable exception from happening when
running the driver.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the unused variables in
cpmac_hw_error, cpmac_tx_timeout and cpmac_probe.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a generic driver for SJA1000 chips on the OpenFirmware
platform bus found on embedded PowerPC systems. You need a SJA1000 node
definition in your flattened device tree source (DTS) file similar to:
can@3,100 {
compatible = "nxp,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 0>;
interrupt-parent = <&mpic>;
nxp,external-clock-frequency = <16000000>;
};
See also Documentation/powerpc/dts-bindings/can/sja1000.txt.
CC: devicetree-discuss@ozlabs.org
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As discussed on the netdev mailing list, the member "base_addr" of
"struct net_device" should not be (mis)used to store the virtual
address to the SJA1000 register area. According to David Miller,
it's only use is to allow ISA and similar primitive bus devices to
have their I/O ports changed via ifconfig. The virtual address is
now stored in the private data structure of the SJA1000 device and
the callback functions use "struct sja1000_priv" instead of the
unneeded "struct net_device".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a few errors sneaked into the initial version of the
device driver interface.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Warning messages coming from rtl8150 driver can flood the console
and make a DTV/set-top-box unable to decode video/audio frames.
'Pegasus' driver handles this situation similarly, preventing this
from happening there.
It happens with a low cost BCM MIPS embedded platform, whenever
timeout errors were coming from usbnet device, making platform
unusable for viewer watching.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add FEC support for MX35 processor.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds power management suspend/resume hooks for irda-usb.
Signed-off-by: Tadashi Abe <tabe@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mac8390: use printk MAC address format
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Gary Lin reports that a new device id needs to be added to the atl1e in
order to get some new Asus hardware to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the transmit queue gets full we enable interrupts for TX completions
There was a race that we handled the TX queue both from the interrupt context
and from the transmit function. Using "spin_trylock_irq()" ensures this
doesn't happen.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Add support for the Aquantia AQ1002 10G-BaseT phy.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the AEL2020 phy.
Add PCI IDs of the boards using this phy.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cxgb3 no longer advertizes LLTX.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we register the MII bus to the platfrom bus, the Distributed Switch
Architecture can hook in transparently.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Remove dead long delay
- Use proper defines
- Remove broken implementation of the TX DMA Data Alignment TXDWA feature
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Writes to the DMA descriptors may sit in the internal Blackfin data buffers
and not actually be available when the DMA engine goes to fetch them. This
does not typically happen, but when dealing with short/fast packets such as
UDP and polling KGDB, this occurs much more frequently. Same goes for
heavy loads as seen by netperf tests or large scp transfers. So force the
buffers to drain with SSYNC otherwise we get random malformed packets.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IRQ used by the Blackfin EMAC is internal to the peripheral and cannot
be used to generate any other interrupt, so there is no point in marking it
as IRQF_SHARED.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to release skb->dst, its now done by core network.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=13383
Reported-by: Przemyslaw Kulczycki <azrael@autocom.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=13312
at76_dwork_hw_scan holds a mutex while calling ieee80211_scan_completed,
which then calls at76_config which needs the same mutex. This reworks
the ordering to not hold the lock while calling ieee80211_scan_completed.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix the build for CONFIG_NET_POLL_CONTROLLER that I broke with
217cbfa856dc1cbc2890781626c4032d9e3ec59f ("mac8390: fix regression
caused during net_device_ops conversion").
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not call t3_link_fault() under spinlock, as it calls msleep().
Besides, only the access to pi->link_fault needs to be serialized.
Also initialize local variables before checking the link status,
link state fields might otherwise end up containing garbage.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5e68b772e6efd189d6aca76f6872fb75d51ace60
cxgb3: map entire Rx page, feed map+offset to Rx ring.
introduced a regression on platforms defining DECLARE_PCI_UNMAP_ADDR()
and related macros as no-ops.
Rx descriptors are fed with the a page buffer bus address + page chunk offset.
The page buffer bus address is set and retrieved through
pci_unamp_addr_set(), pci_unmap_addr().
These functions being meaningless on x86 (if CONFIG_DMA_API_DEBUG is not set).
The HW ends up with a bogus bus address.
This patch saves the page buffer bus address for all plaftorms.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes the korina driver poll the media
for link change. This is actually required on
Mikrotik RB532 (not RB532A) for korina to
operate properly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This replaces dma_sync_single() with dma_sync_single_for_cpu() because
dma_sync_single() is an obsolete API; include/linux/dma-mapping.h says:
/* Backwards compat, remove in 2.7.x */
#define dma_sync_single dma_sync_single_for_cpu
#define dma_sync_sg dma_sync_sg_for_cpu
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
