| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Drivers that define PSEUDO_DMA also define NCR5380_dma_xfer_len.
The core driver must call NCR5380_dma_xfer_len which means
FLAG_NO_PSEUDO_DMA can be eradicated from the core driver.
dmx3191d doesn't define PSEUDO_DMA and has no use for FLAG_NO_PSEUDO_DMA,
so remove it there also.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This change brings a number of improvements: fewer macros, better test
coverage, simpler code and sane Kconfig options. The downside is a small
chance of incompatibility (which seems unavoidable).
CONFIG_SCSI_GENERIC_NCR53C400 exists to enable or inhibit pseudo DMA
transfers when the driver is used with 53C400-compatible cards. Thanks to
Ondrej Zary's patches, PDMA now works which means it can be enabled
unconditionally.
Due to bad design, CONFIG_SCSI_GENERIC_NCR53C400 ties together unrelated
functionality as it sets both PSEUDO_DMA and BIOSPARAM macros. This patch
effectively enables PSEUDO_DMA and disables BIOSPARAM.
The defconfigs and the Kconfig default leave CONFIG_SCSI_GENERIC_NCR53C400
undefined. Red Hat 9 and CentOS 2.1 were the same. This leaves both
PSEUDO_DMA and BIOSPARAM disabled. The effect of this patch should be
better performance from enabling PSEUDO_DMA.
On the other hand, Debian 4 and SLES 10 had CONFIG_SCSI_GENERIC_NCR53C400
enabled, so both PSEUDO_DMA and BIOSPARAM were enabled. This patch might
affect configurations like this by disabling BIOSPARAM. My best guess is
that this could be a problem only in the vanishingly rare case that
1) the CHS values stored in the boot device partition table are wrong and
2) a 5380 card is in use (because PDMA on 53C400 used to be broken).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On 64 bit, struct error_info has 6 bytes of padding, which amounts to
over 4k of wasted space in the additional[] array. We could easily get
rid of that by instead using separate arrays for the codes and the
pointers. However, we can do even better than that and save an
additional 6 bytes per entry: In the table, just store the sizeof()
the corresponding string literal. The cumulative sum of these is then
the appropriate offset into additional_text, which is built from the
concatenation (with '\0's inbetween) of the strings.
$ scripts/bloat-o-meter /tmp/vmlinux vmlinux
add/remove: 0/0 grow/shrink: 1/1 up/down: 24/-8488 (-8464)
function old new delta
scsi_extd_sense_format 136 160 +24
additional 11312 2824 -8488
The Kconfig help text used to say that CONFIG_SCSI_CONSTANTS=y costs
around 75 KB, but that was a little exaggerated. The actual number was
closer to 44K, and 36K with this patch.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This is a purely mechanical move of the list of additional sense codes
to a separate file, in preparation for reducing the impact of choosing
CONFIG_SCSI_CONSTANTS=y by about 8k.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There's little point in breaking these strings over multiple lines.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for how scaling linearization is computed in wiimote driver, by
Cyan Ogilvie
- endless retry loop fix in generic USB HID core reset-resume handling,
by Alan Stern
- two functional fixes affecting particular devices, and oops fix for
wacom driver, by Jason Gerecke
- multitouch slot numbering fix from Gabriele Mazzotta
- a couple more small fixes on top
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: Support switching from vendor-defined device mode on G9 and G11
HID: wacom: Initialize hid_data.inputmode to -1
HID: microsoft: add support for 3 more devices
HID: multitouch: Synchronize MT frame on reset_resume
HID: wacom: fix Bamboo ONE oops
HID: lenovo: Don't use stack variables for DMA buffers
HID: usbhid: fix inconsistent reset/resume/reset-resume behavior
HID: wiimote: Fix wiimote mp scale linearization
|
|
Pull MMC fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.6 rc3:
MMC host:
- sdhci: Fix regression setting power on Trats2 board
- sdhci-pci: Add support and PCI IDs for more Broxton host controllers"
* tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pci: Add support and PCI IDs for more Broxton host controllers
mmc: sdhci: Fix regression setting power on Trats2 board
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some bugfixes from I2C:
- fix a uevent triggered boot problem by removing a useless debug
print
- fix sysfs-attributes of the new i2c-demux-pinctrl driver to follow
standard kernel behaviour
- fix a potential division-by-zero error (needed two takes)"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: jz4780: really prevent potential division by zero
Revert "i2c: jz4780: prevent potential division by zero"
i2c: jz4780: prevent potential division by zero
i2c: mux: demux-pinctrl: Update docs to new sysfs-attributes
i2c: mux: demux-pinctrl: Clean up sysfs attributes
i2c: prevent endless uevent loop with CONFIG_I2C_DEBUG_CORE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Three fixes, the first two are tagged for -stable:
- The ndctl utility/library gained expanded unit tests illuminating a
long standing bug in the libnvdimm SMART data retrieval
implementation.
It has been broken since its initial implementation, now fixed.
- Another one line fix for the detection of stale info blocks.
Without this change userspace can get into a situation where it is
unable to reconfigure a namespace.
- Fix the badblock initialization path in the presence of the new (in
v4.6-rc1) section alignment workarounds.
Without this change badblocks will be reported at the wrong offset.
These have received a build success report from the kbuild robot and
have appeared in -next with no reported issues"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignment
libnvdimm, pfn: fix uuid validation
libnvdimm: fix smart data retrieval
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a set of four GPIO fixes. The two fixes to the core are
serious as they are regressing minor architectures.
Core fixes:
- Defer GPIO device setup until after gpiolib is initialized.
It turns out that a few very tightly integrated GPIO platform
drivers initialize so early (befor core_initcall()) so that the
gpiolib isn't even initialized itself. That limits what the
library can do, and we cannot reference uninitialized fields until
later.
Defer some of the initialization until right after the gpiolib is
initialized in these (rare) cases.
- As a consequence: do not use devm_* resources when allocating the
states in the initial set-up of the gpiochip.
Driver fixes:
- In ACPI retrieveal: ignore GpioInt when looking for output GPIOs.
- Fix legacy builds on the PXA without a backing pin controller.
- Use correct datatype on pca953x register writes"
* tag 'gpio-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Use correct u16 value for register word write
gpiolib: Defer gpio device setup until after gpiolib initialization
gpiolib: Do not use devm functions when registering gpio chip
gpio: pxa: fix legacy non pinctrl aware builds
gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty fixes for issues found.
One was due to a merge error in 4.6-rc1, and the other a regression
fix for UML consoles that broke in 4.6-rc1.
Both have been in linux-next for a while"
* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix merge of "tty: Refactor tty_open()"
tty: Fix UML console breakage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as
they are 'trivial'"
* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: option: add "D-Link DWM-221 B1" device id
USB: serial: cp210x: Adding GE Healthcare Device ID
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
usb: dwc3: keystone: drop dma_mask configuration
usb: gadget: udc-core: remove manual dma configuration
usb: dwc3: pci: add ID for one more Intel Broxton platform
usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
usb: dwc2: do not override forced dr_mode in gadget setup
usb: gadget: f_midi: unlock on error
USB: digi_acceleport: do sanity checking for the number of ports
USB: cypress_m8: add endpoint sanity check
USB: mct_u232: add sanity checking in probe
usb: fix regression in SuperSpeed endpoint descriptor parsing
USB: usbip: fix potential out-of-bounds write
usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
usb: phy: qcom-8x16: fix regulator API abuse
usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
usb: gadget: composite: Access SSP Dev Cap fields properly
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some IIO driver fixes, along with two staging driver fixes
for 4.6-rc3.
One staging driver patch reverts the deletion of a driver that
happened in 4.6-rc1. We thought that laptop.org was dead, but it's
still alive and kicking, and has users that were mad we broke their
hardware by deleting a driver for their machines. So that driver is
added back and everyone is happy again.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: olpc_dcon: Remove obsolete driver"
staging/rdma/hfi1: select CRC32
iio: gyro: bmg160: fix buffer read values
iio: gyro: bmg160: fix endianness when reading axes
iio: accel: bmc150: fix endianness when reading axes
iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
iio: fix config watermark initial value
iio: health: max30100: correct FIFO check condition
iio: imu: Fix inv_mpu6050 dependencies
iio: adc: Fix build error of missing devm_ioremap_resource on UM
iio: light: apds9960: correct FIFO check condition
iio: adc: max1363: correct reference voltage
iio: adc: max1363: add missing adc to max1363_id
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of eight fixes.
Two are trivial gcc-6 updates (brace additions and unused variable
removal). There's a couple of cxlflash regressions, a correction for
sd being overly chatty on revalidation (causing excess log increases).
A VPD issue which could crash USB devices because they seem very
intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
overrun fix"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Do not attach VPD to devices that don't support it
sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
scsi_dh_alua: Fix a recently introduced deadlock
scsi: Declare local symbols static
cxlflash: Move to exponential back-off when cmd_room is not available
cxlflash: Fix regression issue with re-ordering patch
mpt3sas: Don't overreach ioc->reply_post[] during initialization
aacraid: add missing curly braces
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
"This update mainly fixes bugs:
- fix error handling (Guoqing)
- fix a crash when a disk is hotremoved (me)
- fix a dead loop (Wei Fang)"
* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/bitmap: clear bitmap if bitmap_create failed
MD: add rdev reference for super write
md: fix a trivial typo in comments
md:raid1: fix a dead loop when read from a WriteMostly disk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for some issues discovered after recent changes and for some
that have just been found lately regardless of those changes
(intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
support for some new CPU models (intel_idle, Intel RAPL driver,
turbostat) and documentation updates (intel_pstate, PM core).
Specifics:
- intel_pstate fixes for two issues exposed by the recent switch over
from using timers and for one issue introduced during the 4.4 cycle
plus new comments describing data structures used by the driver
(Rafael Wysocki, Srinivas Pandruvada).
- intel_idle fixes related to CPU offline/online (Richard Cochran).
- intel_idle support (new CPU IDs and state definitions mostly) for
Skylake-X and Kabylake processors (Len Brown).
- PCC mailbox driver fix for an out-of-bounds memory access that may
cause the kernel to panic() (Shanker Donthineni).
- New (missing) CPU ID for one apparently overlooked Haswell model in
the Intel RAPL power capping driver (Srinivas Pandruvada).
- Fix for the PM core's wakeup IRQs framework to make it work after
wakeup settings reconfiguration from sysfs (Grygorii Strashko).
- Runtime PM documentation update to make it describe what needs to
be done during device removal more precisely (Krzysztof Kozlowski).
- Stale comment removal cleanup in the cpufreq-dt driver (Viresh
Kumar).
- turbostat utility fixes and support for Broxton, Skylake-X and
Kabylake processors (Len Brown)"
* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
...
|
|
Pull networking fixes from David Miller:
1) Stale SKB data pointer access across pskb_may_pull() calls in L2TP,
from Haishuang Yan.
2) Fix multicast frame handling in mac80211 AP code, from Felix
Fietkau.
3) mac80211 station hashtable insert errors not handled properly, fix
from Johannes Berg.
4) Fix TX descriptor count limit handling in e1000, from Alexander
Duyck.
5) Revert a buggy netdev refcount fix in netpoll, from Bjorn Helgaas.
6) Must assign rtnl_link_ops of the device before registering it, fix
in ip6_tunnel from Thadeu Lima de Souza Cascardo.
7) Memory leak fix in tc action net exit, from WANG Cong.
8) Add missing AF_KCM entries to name tables, from Dexuan Cui.
9) Fix regression in GRE handling of csums wrt. FOU, from Alexander
Duyck.
10) Fix memory allocation alignment and congestion map corruption in
RDS, from Shamir Rabinovitch.
11) Fix default qdisc regression in tuntap driver, from Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge, netem: mark mailing lists as moderated
tuntap: restore default qdisc
mpls: find_outdev: check for err ptr in addition to NULL check
ipv6: Count in extension headers in skb->network_header
RDS: fix congestion map corruption for PAGE_SIZE > 4k
RDS: memory allocated must be align to 8
GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
net: add the AF_KCM entries to family name tables
MAINTAINERS: intel-wired-lan list is moderated
lib/test_bpf: Add additional BPF_ADD tests
lib/test_bpf: Add test to check for result of 32-bit add that overflows
lib/test_bpf: Add tests for unsigned BPF_JGT
lib/test_bpf: Fix JMP_JSET tests
VSOCK: Detach QP check should filter out non matching QPs.
stmmac: fix adjust link call in case of a switch is attached
af_packet: tone down the Tx-ring unsupported spew.
net_sched: fix a memory leak in tc action
samples/bpf: Enable powerpc support
samples/bpf: Use llc in PATH, rather than a hardcoded value
samples/bpf: Fix build breakage with map_perf_test_user.c
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- compile-time fixes (warnings and failures)
- a bug in iommu core code which could cause the group->domain pointer
to be falsly cleared
- fix in scatterlist handling of the ARM common DMA-API code
- stall detection fix for the Rockchip IOMMU driver
* tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Silence an uninitialized variable warning
iommu/rockchip: Fix "is stall active" check
iommu: Don't overwrite domain pointer when there is no default_domain
iommu/dma: Restore scatterlist offsets correctly
iommu: provide of_xlate pointer unconditionally
|
|
Make sure we avoid a division-by-zero OOPS in case clock-frequency is
set too low in DT. Add missing '\n' while we are here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Axel Lin <axel.lin@ingics.com>
|
|
This reverts commit 34cf2acdafaa31a13821e45de5ee896adcd307b1. 'ret' is
not set when bailing out. Also, there is a better place to check for 0.
Reported-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.6-rc3
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
After commit f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using
alloc_netdev"), default qdisc was changed to noqueue because
tuntap does not set tx_queue_len during .setup(). This patch restores
default qdisc by setting tx_queue_len in tun_setup().
Fixes: f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using alloc_netdev")
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* pm-core:
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
PM / runtime: Document steps for device removal
* powercap:
powercap: intel_rapl: Add missing Haswell model
* pm-tools:
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
|
|
* pm-cpufreq:
cpufreq: dt: Drop stale comment
cpufreq: intel_pstate: Documenation for structures
cpufreq: intel_pstate: fix inconsistency in setting policy limits
intel_pstate: Avoid extra invocation of intel_pstate_sample()
intel_pstate: Do not set utilization update hook too early
* pm-cpuidle:
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
* acpi-cppc:
mailbox: pcc: Don't access an unmapped memory address space
|
|
The current implementation only uses the first byte in val,
the second byte is always 0. Change it to use cpu_to_le16
to write the two bytes into the register
Cc: stable@vger.kernel.org
Signed-off-by: Yong Li <sdliyong@gmail.com>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since commit ff2b13592299 ("gpio: make the gpiochip a real device"),
attempts to add a gpio chip prior to gpiolib initialization cause
the system to crash. This happens because gpio_bus_type has not been
registered yet. Defer creating gpio devices until after gpiolib has
been initialized to fix the problem.
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Fixes: ff2b13592299 ("gpio: make the gpiochip a real device")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It is possible that a gpio chip is registered before the gpiolib
initialization code has run. This means we can not use devm_ functions
to allocate memory at that time. Do it the old fashioned way.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In legacy pxa builds, ie. non device-tree and platform-data only builds,
pinctrl is not yet available. As a consequence, the pinctrl gpio
direction change function is a stub, returning always success.
In the current state, the gpio driver direction function believes the
pinctrl direction change was successful, and exits without actually
changing the gpio direction.
This patch changes the logic :
- if the pinctrl direction function fails, gpio direction will report
that failure
- if the pinctrl direction function succeeds, gpio direction is changed
by the gpio driver anyway.
This is sub optimal in the pinctrl aware case, as the gpio direction
will be changed twice: once by pinctrl function and another time by
the gpio direction function.
Yet it should be acceptable in this form, as this is functional for all
pxa platforms (device-tree and platform-data), and moreover changing a
gpio direction is very very seldom, usually in machine initialization,
seldom in drivers probe, and an exception for ac97 reset bug.
Fixes: a770d946371e ("gpio: pxa: add pin control gpio direction and request")
Reported-by: Guenter Roeck <guenter@roeck-us.net>
Tested-by: Guenter Roeck <guenter@roeck-us.net>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When firmware does not use _DSD properties that allow properly name GPIO
resources, the kernel falls back on parsing _CRS resources, and will
return entries described as GpioInt() as general purpose GPIOs even
though they are meant to be used simply as interrupt sources for the
device:
Device (ETSA)
{
Name (_HID, "ELAN0001")
...
Method(_CRS, 0x0, NotSerialized)
{
Name(BUF0,ResourceTemplate ()
{
I2CSerialBus(
0x10, /* SlaveAddress */
ControllerInitiated, /* SlaveMode */
400000, /* ConnectionSpeed */
AddressingMode7Bit, /* AddressingMode */
"\\_SB.I2C1", /* ResourceSource */
)
GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone,,
"\\_SB.GPSW") { BOARD_TOUCH_GPIO_INDEX }
} )
Return (BUF0)
}
...
}
This gives troubles with drivers such as Elan Touchscreen driver
(elants_i2c) that uses devm_gpiod_get to look up "reset" GPIO line and
decide whether the driver is responsible for powering up and resetting
the device, or firmware is. In the above case the lookup succeeds, we
map GPIO as output and later fail to request client->irq interrupt that
is mapped to the same GPIO.
Let's ignore resources described as GpioInt() while parsing _CRS when
requesting output GPIOs (but allow them when requesting GPIOD_ASIS or
GPIOD_IN as some drivers, such as i2c-hid, do request GPIO as input and
then map it to interrupt with gpiod_to_irq).
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When section alignment padding is in effect we need to shift / truncate
the range that is queried for poison by the 'start_pad' or 'end_trunc'
reservations.
It's easiest if we just pass in an adjusted resource range rather than
deriving it from the passed in namespace. With the resource range
resolution pushed out to the caller we can also push the
namespace-to-region lookup to the caller and drop the implicit pmem-type
assumption about the passed in namespace object.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
If we detect a namespace has a stale info block in the init path, we
should overwrite with the latest configuration. In fact, we already
return -ENODEV when the parent uuid is invalid, the same should be done
for the 'self' uuid. Otherwise we can get into a condition where
userspace is unable to reconfigure the pfn-device without directly /
manually invalidating the info block.
Cc: <stable@vger.kernel.org>
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
It appears that smart data retrieval has been broken the since the
initial implementation. Fix the payload size to be 128-bytes per the
specification.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This reverts commit 0fd10721fe3664f7549e74af9d28a509c9a68719.
That patch causes the ib_srpt driver to crash as soon as the first SCSI
command is received:
kernel BUG at drivers/infiniband/ulp/srpt/ib_srpt.c:1439!
invalid opcode: 0000 [#1] SMP
Workqueue: target_completion target_complete_ok_work [target_core_mod]
RIP: srpt_queue_response+0x437/0x4a0 [ib_srpt]
Call Trace:
srpt_queue_data_in+0x9/0x10 [ib_srpt]
target_complete_ok_work+0x152/0x2b0 [target_core_mod]
process_one_work+0x197/0x480
worker_thread+0x49/0x490
kthread+0xea/0x100
ret_from_fork+0x22/0x40
Aside from the crash, the shortcomings of that patch are as follows:
- It makes the ib_srpt driver use I/O contexts allocated by
transport_alloc_session_tags() but it does not initialize these I/O
contexts properly. All the initializations performed by
srpt_alloc_ioctx() are skipped.
- It swaps the order of the send ioctx allocation and the transition to
RTR mode which is wrong.
- The amount of memory that is needed for I/O contexts is doubled.
- srpt_rdma_ch.free_list is no longer used but is not removed.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fix from Sage Weil:
"This just fixes a few remaining memory allocations in RBD to use
GFP_NOIO instead of GFP_ATOMIC"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use GFP_NOIO consistently for request allocations
|
|
Pull virtio/qemu fixes from Michael S Tsirkin:
"A couple of fixes for virtio and for the new QEMU fw cfg driver"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: add VIRTIO_CONFIG_S_NEEDS_RESET device status bit
MAINTAINERS: add entry for QEMU
firmware: qemu_fw_cfg.c: hold ACPI global lock during device access
virtio: virtio 1.0 cs04 spec compliance for reset
qemu_fw_cfg: don't leak kobj on init error
|
|
Pull drm fixes from Dave Airlie:
"This is mostly amdgpu/radeon fixes, and imx related fixes.
There is also one one TTM fix, one nouveau fix, and one hdlcd fix.
The AMD ones are some fixes for power management after suspend/resume
one some GPUs, and some vblank fixes.
The IMX ones are for more stricter plane checks and some cleanups.
I'm off until Monday, so therre might be some fixes early next week if
anyone missed me"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (34 commits)
drm/nouveau/tegra: acquire and enable reference clock if needed
drm/amdgpu: total vram size also reduces pin size
drm/amd/powerplay: add uvd/vce dpm enabling flag default.
drm/amd/powerplay: fix issue that resume back, dpm can't work on FIJI.
drm/amdgpu: save and restore the firwmware cache part when suspend resume
drm/amdgpu: save and restore UVD context with suspend and resume
drm/ttm: use phys_addr_t for ttm_bus_placement
drm: ARM HDLCD - fix an error code
drm: ARM HDLCD - get rid of devm_clk_put()
drm/radeon: Only call drm_vblank_on/off between drm_vblank_init/cleanup
drm/amdgpu: fence wait old rcu slot
drm/amdgpu: fix leaking fence in the pageflip code
drm/amdgpu: print vram type rather than just DDR
drm/amdgpu/gmc: use proper register for vram type on Fiji
drm/amdgpu/gmc: move vram type fetching into sw_init
drm/amdgpu: Set vblank_disable_allowed = true
drm/radeon: Set vblank_disable_allowed = true
drm/amd/powerplay: Need to change boot to performance state in resume.
drm/amd/powerplay: add new Fiji function for not setting same ps.
drm/amdgpu: check dpm state before pm system fs initialized.
...
|
|
Now wakeirq stops working for device if wakeup option for
this device will be reconfigured through sysfs, like:
echo disabled > /sys/devices/platform/extcon_usb1/power/wakeup
echo enabled > /sys/devices/platform/extcon_usb1/power/wakeup
Once above set of commands is executed the device's wakeup_source
opject will be recreated and dev->power.wakeup->wakeirq field will
contain NULL. As result, device_wakeup_arm_wake_irqs() will not arm
wakeirq for the affected device.
Hece, lets try to fix it in the following way:
check for dev->wakeirq field when device_wakeup_attach() is called
and if !NULL re-attach wakeirq to the device
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
KBL is similar to SKL
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
SKX is similar to BDX
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver registers cpuidle devices when a CPU comes online, but it
leaves the registrations in place when a CPU goes offline. The module
exit code only unregisters the currently online CPUs, leaving the
devices for offline CPUs dangling.
This patch changes the driver to clean up all registrations on exit,
even those from CPUs that are offline.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If a cpuidle registration error occurs during the hot plug notifier
callback, we should really inform the hot plug machinery instead of
just ignoring the error. This patch changes the callback to properly
return on error.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The helper function, intel_idle_cpu_init, registers one new device
with the cpuidle layer. If the registration should fail, that
function immediately calls intel_idle_cpuidle_devices_uninit() to
unregister every last CPU's device. However, it makes no sense to do
so, when called from the hot plug notifier callback.
This patch moves the call to intel_idle_cpuidle_devices_uninit()
outside of the helper function to the one call site that actually
needs to perform the de-registrations.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver sets the broadcast tick quite early on during probe and does
not clean up again in cast of failure. This patch moves the setup call
after the registration, placing the on_each_cpu() calls within the global
CPU lock region.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The helper function, intel_idle_cpuidle_devices_uninit, frees the
globally allocated per-CPU data. However, this function is invoked
from the hot plug notifier callback at a time when freeing that data
is not safe.
If the call to cpuidle_register_driver() should fail (say, due to lack
of memory), then the driver will free its per-CPU region. On the
*next* CPU_ONLINE event, the driver will happily use the region again
and even free it again if the failure repeats.
This patch fixes the issue by moving the call to free_percpu() outside
of the helper function at the two call sites that actually need to
free the per-CPU data.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the module_init() method, if the per-CPU allocation fails, then the
active cpuidle registration is not cleaned up. This patch fixes the
issue by attempting the allocation before registration, and then
cleaning it up again on registration failure.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the module_exit() method, this driver first frees its per-CPU
pointer, then unregisters a callback making use of the pointer.
Furthermore, the function, intel_idle_cpuidle_devices_uninit, is racy
against CPU hot plugging as it calls for_each_online_cpu().
This patch corrects the issues by unregistering first on the exit path
while holding the hot plug lock.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function, intel_idle_cpuidle_driver_init, makes calls on each CPU
to auto_demotion_disable() and c1e_promotion_disable(). These calls
are redundant, as intel_idle_cpu_init() does the same calls just a bit
later on. They are also premature, as the driver registration may yet
fail.
This patch removes the redundant code.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function, intel_idle_cpuidle_driver_init, delivers no error codes
at all. This patch changes the function to return 'void' instead of
returning zero.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make sure we don't OOPS in case clock-frequency is set to 0 in a DT. The
variable set here is later used as a divisor.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
