| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit bed9ff165960921303a100228585f2d1691b42eb upstream.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed18c5fa945768a9bec994e786edbbbc7695acf6 upstream.
This optimization significantly reduces xhci driver load time.
In ACPI tables the acpi companion port devices are children of
the hub device. The port devices are identified by their port number
returned by the ACPI _ADR method.
_ADR 0 is reserved for the root hub device.
The current implementation to find a acpi companion port device
loops through all acpi port devices under that parent hub, evaluating
their _ADR method each time a new port device is added.
for a xHC controller with 25 ports under its roothub it
will end up invoking ACPI bytecode 625 times before all ports
are ready, making it really slow.
The _ADR values are already read and cached earler. So instead of
running the bytecode again we can check the cached _ADR value first,
and then fall back to the old way.
As one of the more significant changes, the xhci load time on
Intel kabylake reduced by 70%, (28ms) from
initcall xhci_pci_init+0x0/0x49 returned 0 after 39537 usecs
to
initcall xhci_pci_init+0x0/0x49 returned 0 after 11270 usecs
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 277867ade8262583f4280cadbe90e0031a3706a7 upstream.
of_find_compatible_node() is calling of_node_put() on its first argument
thus leading to an unbalanced of_node_get/put() issue if the node has not
been retained before that.
Instead of passing the root node, pass NULL, which does exactly the same:
iterate over all DT nodes, starting from the root node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: 3d61467f9bab ("irqchip: atmel-aic: Implement RTC irq fixup")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 469bcef53c546bb792aa66303933272991b7831d upstream.
aic_common_irq_fixup() is calling twice of_node_put() on the same node
thus leading to an unbalanced refcount on the root node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: b2f579b58e93 ("irqchip: atmel-aic: Add irq fixup infrastructure")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b15bd8cb37598afb2963f7eb9e2de468d2d60a2f upstream.
Since commit d05d7f40791c ("Merge branch 'for-4.8/core' of
git://git.kernel.dk/linux-block") and 3fc9d690936f ("Merge branch
'for-4.8/drivers' of git://git.kernel.dk/linux-block"), blkfront_resume()
has been using an index for iterating ring_info to check request when
iterating blk_shadow in an inner loop. This seems to have been
accidentally introduced during the massive rewrite of the block layer
macros in the commits.
This may cause crash like this:
[11798.057074] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[11798.058832] IP: [<ffffffff814411fa>] blkfront_resume+0x10a/0x610
....
[11798.061063] Call Trace:
[11798.061063] [<ffffffff8139ce93>] xenbus_dev_resume+0x53/0x140
[11798.061063] [<ffffffff8139ce40>] ? xenbus_dev_probe+0x150/0x150
[11798.061063] [<ffffffff813f359e>] dpm_run_callback+0x3e/0x110
[11798.061063] [<ffffffff813f3a08>] device_resume+0x88/0x190
[11798.061063] [<ffffffff813f4cc0>] dpm_resume+0x100/0x2d0
[11798.061063] [<ffffffff813f5221>] dpm_resume_end+0x11/0x20
[11798.061063] [<ffffffff813950a8>] do_suspend+0xe8/0x1a0
[11798.061063] [<ffffffff813954bd>] shutdown_handler+0xfd/0x130
[11798.061063] [<ffffffff8139aba0>] ? split+0x110/0x110
[11798.061063] [<ffffffff8139ac26>] xenwatch_thread+0x86/0x120
[11798.061063] [<ffffffff810b4570>] ? prepare_to_wait_event+0x110/0x110
[11798.061063] [<ffffffff8108fe57>] kthread+0xd7/0xf0
[11798.061063] [<ffffffff811da811>] ? kfree+0x121/0x170
[11798.061063] [<ffffffff8108fd80>] ? kthread_park+0x60/0x60
[11798.061063] [<ffffffff810863b0>] ? call_usermodehelper_exec_work+0xb0/0xb0
[11798.061063] [<ffffffff810864ea>] ? call_usermodehelper_exec_async+0x13a/0x140
[11798.061063] [<ffffffff81534a45>] ret_from_fork+0x25/0x30
Use the right index in the inner loop.
Fixes: d05d7f40791c ("Merge branch 'for-4.8/core' of git://git.kernel.dk/linux-block")
Fixes: 3fc9d690936f ("Merge branch 'for-4.8/drivers' of git://git.kernel.dk/linux-block")
Signed-off-by: Munehisa Kamata <kamatam@amazon.com>
Reviewed-by: Thomas Friebel <friebelt@amazon.de>
Reviewed-by: Eduardo Valentin <eduval@amazon.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Roger Pau Monne <roger.pau@citrix.com>
Cc: xen-devel@lists.xenproject.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 462cdace790ac2ed6aad1b19c9c0af0143b6aab0 upstream.
The current test for bio vec merging is not fully accurate and can be
tricked into merging bios when certain grant combinations are used.
The result of these malicious bio merges is a bio that extends past
the memory page used by any of the originating bios.
Take into account the following scenario, where a guest creates two
grant references that point to the same mfn, ie: grant 1 -> mfn A,
grant 2 -> mfn A.
These references are then used in a PV block request, and mapped by
the backend domain, thus obtaining two different pfns that point to
the same mfn, pfn B -> mfn A, pfn C -> mfn A.
If those grants happen to be used in two consecutive sectors of a disk
IO operation becoming two different bios in the backend domain, the
checks in xen_biovec_phys_mergeable will succeed, because bfn1 == bfn2
(they both point to the same mfn). However due to the bio merging,
the backend domain will end up with a bio that expands past mfn A into
mfn A + 1.
Fix this by making sure the check in xen_biovec_phys_mergeable takes
into account the offset and the length of the bio, this basically
replicates whats done in __BIOVEC_PHYS_MERGEABLE using mfns (bus
addresses). While there also remove the usage of
__BIOVEC_PHYS_MERGEABLE, since that's already checked by the callers
of xen_biovec_phys_mergeable.
Reported-by: "Jan H. Schönherr" <jschoenh@amazon.de>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit afc1f55ca44e257f69da8f43e0714a76686ae8d1 upstream.
->safemode should be triggered by mdadm for external metadaa array, otherwise
array's state confuses mdadm.
Fixes: 33182d15c6bf(md: always clear ->safemode when md_check_recovery gets the mddev lock.)
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 33182d15c6bf182f7ae32a66ea4a547d979cd6d7 upstream.
If ->safemode == 1, md_check_recovery() will try to get the mddev lock
and perform various other checks.
If mddev->in_sync is zero, it will call set_in_sync, and clear
->safemode. However if mddev->in_sync is not zero, ->safemode will not
be cleared.
When md_check_recovery() drops the mddev lock, the thread is woken
up again. Normally it would just check if there was anything else to
do, find nothing, and go to sleep. However as ->safemode was not
cleared, it will take the mddev lock again, then wake itself up
when unlocking.
This results in an infinite loop, repeatedly calling
md_check_recovery(), which RCU or the soft-lockup detector
will eventually complain about.
Prior to commit 4ad23a976413 ("MD: use per-cpu counter for
writes_pending"), safemode would only be set to one when the
writes_pending counter reached zero, and would be cleared again
when writes_pending is incremented. Since that patch, safemode
is set more freely, but is not reliably cleared.
So in md_check_recovery() clear ->safemode before checking ->in_sync.
Fixes: 4ad23a976413 ("MD: use per-cpu counter for writes_pending")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reported-by: David R <david@unsolicited.net>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81fe48e9aa00bdd509bd3c37a76d1132da6b9f09 upstream.
md_write_start() needs to clear the in_sync flag is it is set, or if
there might be a race with set_in_sync() such that the later will
set it very soon. In the later case it is sufficient to take the
spinlock to synchronize with set_in_sync(), and then set the flag
if needed.
The current test is incorrect.
It should be:
if "flag is set" or "race is possible"
"flag is set" is trivially "mddev->in_sync".
"race is possible" should be tested by "mddev->sync_checkers".
If sync_checkers is 0, then there can be no race. set_in_sync() will
wait in percpu_ref_switch_to_atomic_sync() for an RCU grace period,
and as md_write_start() holds the rcu_read_lock(), set_in_sync() will
be sure ot see the update to writes_pending.
If sync_checkers is > 0, there could be race. If md_write_start()
happened entirely between
if (!mddev->in_sync &&
percpu_ref_is_zero(&mddev->writes_pending)) {
and
mddev->in_sync = 1;
in set_in_sync(), then it would not see that is_sync had been set,
and set_in_sync() would not see that writes_pending had been
incremented.
This bug means that in_sync is sometimes not set when it should be.
Consequently there is a small chance that the array will be marked as
"clean" when in fact it is inconsistent.
Fixes: 4ad23a976413 ("MD: use per-cpu counter for writes_pending")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76988690402dde2880bfe06ecccf381d48ba8e1c upstream.
Add 2 new IDs (ELAN0609 and ELAN060B) to the list of ACPI IDs that should
be handled by the driver.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1874064eed0502bd9bef7be8023757b0c4f26883 upstream.
Similar to commit 722c5ac708b4f ("Input: elan_i2c - add ELAN0605 to the
ACPI table"), ELAN0608 should be handled by elan_i2c.
This touchpad can be found in Lenovo ideapad 320-14IKB.
BugLink: https://bugs.launchpad.net/bugs/1708852
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a7c286d07f9c704e8fd11dd960bf421cc67b66b upstream.
update the list first to avoid redundant checks.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0125a932e917cb507b682cb66645efdca1f8cab upstream.
As we may have just bound the renderstate into the GGTT for execution, we
need to ensure that the GTT TLB are also flushed.
On snb-gt2, this would cause a random GPU hang at the start of a new
context (e.g. boot) and on snb-gt1, it was causing the renderstate batch
to take ~10s. It was the GPU hang that revealed the truth, as the CS
gleefully executed beyond the end of the golden renderstate batch, a good
indicator for a GTT TLB miss.
Fixes: 20fe17aa52dc ("drm/i915: Remove redundant TLB invalidate on switching contexts")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170808131904.1385-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.12-rc1+
(cherry picked from commit 802673d66f8a6ded5d2689d597853c7bb3a70163)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28389575a8cf933a5f3c378556b9f4d3cce0efd2 upstream.
In commit 0f987e25cb8a, the source processing has been moved in front of
the destination processing, but the error handling path has not been
modified accordingly.
Free resources in the correct order to avoid some leaks.
Fixes: 0f987e25cb8a ("crypto: ixp4xx - Fix false lastlen uninitialised warning")
Reported-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4098116039911e8870d84c975e2ec22dab65a909 upstream.
For 64bit kernels the lmmio_space_offset of the host bridge window
isn't set correctly on systems with dino/cujo PCI host bridges.
This leads to not assigned memory bars and failing drivers, which
need to use these bars.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa9556956653f85baaadeb4846dc571414f13e36 upstream.
GPIODV_18 entry was missing in the original driver push.
Fixes: 0f15f500ff2c ("pinctrl: meson: Add GXL pinctrl definitions")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34e61801a3b9df74b69f0e359d64a197a77dd6ac upstream.
GPIODV_18 entry was missing in the original driver push.
Fixes: 468c234f9ed7 ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3fa53ec2ed885b0aec3f0472e3b4a8a6f1cd748c upstream.
The irq chip callbacks irq_request/release_resources() have absolutely no
business with masking and unmasking the irq.
The core code unmasks the interrupt after complete setup and masks it
before invoking irq_release_resources().
The unmask is actually harmful as it happens before the interrupt is
completely initialized in __setup_irq().
Remove it.
Fixes: f6a8249f9e55 ("pinctrl: exynos: Lock GPIOs as interrupts when used as EINTs")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1bd303dc04c3f744474e77c153575087b657f7e1 upstream.
The pingroups dump of debugfs hits WARN_ON() in pinctrl_groups_show().
Filling non-existing ports with '-1' turned out a bad idea.
Fixes: 336306ee1f2d ("pinctrl: uniphier: add UniPhier PH1-LD20 pinctrl driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9592bc256d50481dfcdba93890e576a728fb373c upstream.
The pingroups dump of debugfs hits WARN_ON() in pinctrl_groups_show().
Filling non-existing ports with '-1' turned out a bad idea.
Fixes: 70f2f9c4cf25 ("pinctrl: uniphier: add UniPhier PH1-LD11 pinctrl driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d996132d921c391af5f267123eca1a6a3148ecd upstream.
UART pin lists consist GPIO numbers which is simply wrong.
Replace it by pin numbers.
Fixes: 4e80c8f50574 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d81ece747d8727bb8b1cfc9a20dbe62f09a4e35a upstream.
The PH16 pin has a function with mux id 0x5, which is the DET pin of the
"sim" (smart card reader) IP block.
This function is missing in old versions of A10/A20 SoCs' datasheets and
user manuals, so it's also missing in the old drivers. The newest A10
Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and
it's discovered during implementing R40 pinctrl driver.
Add it to the driver. As we now merged A20 pinctrl driver to the A10
one, we need to only fix the A10 driver now.
Fixes: f2821b1ca3a2 ("pinctrl: sunxi: Move Allwinner A10 pinctrl
driver to a driver of its own")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d80bd3f7eb69204cd5dec4fa7fe7e12cbfaed13 upstream.
Add one more model to the Chromebook DMI quirk to make it working again.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 2a8209fa6823 ("pinctrl: cherryview: Extend the Chromebook DMI quirk to Intel_Strago systems")
Reported-by: mail@abhishek.geek.nz
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d466d3c1217406b14b834335b5b4b33c0d45bd09 upstream.
In order to select the alternate voltage reference pair (VALTH/VALTL), the
right value for the REFSEL field in the ADCx_CFG register is "01", leading
to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1].
[1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf
Fixes: a775427632fd ("iio:adc:imx: add Freescale Vybrid vf610 adc driver")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8466489ef5ba48272ba4fa4ea9f8f403306de4c7 upstream.
The Renesas uPD72020x XHCI controller seems to suffer from a really
annoying bug, where it may retain some of its DMA programming across a XHCI
reset, and despite the driver correctly programming new DMA addresses.
This is visible if the device has been using 64-bit DMA addresses, and is
then switched to using 32-bit DMA addresses. The top 32 bits of the
address (now zero) are ignored are replaced by the 32 bits from the
*previous* programming. Sticking with 64-bit DMA always works, but doesn't
seem very appropriate.
A PCI reset of the device restores the normal functionality, which is done
at probe time. Unfortunately, this has to be done before any quirk has
been discovered, hence the intrusive nature of the fix.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a477b9cd37aa81a490dfa3265b7ff4f2c5a92463 upstream.
The implementation of PCI workarounds may require that the device is reset
from its probe function. This implies that the PCI device lock is already
held, and makes calling pci_reset_function() impossible (since it will
itself try to take that lock).
Add pci_reset_function_locked(), which is the equivalent of
pci_reset_function(), except that it requires the PCI device lock to be
already held by the caller.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[bhelgaas: folded in fix for conflict with 52354b9d1f46 ("PCI: Remove
__pci_dev_reset() and pci_dev_reset()")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52354b9d1f46aae7386db7bb8ec8484b5488087f upstream.
Implement the reset probing / reset chain directly in
__pci_probe_reset_function() and __pci_reset_function_locked()
respectively.
Link: http://lkml.kernel.org/r/20170601111039.8913-4-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b014e96d1abbd67404bbe2018937b46466299e9e upstream.
Every method in struct device_driver or structures derived from it like
struct pci_driver MUST provide exclusion vs the driver's ->remove() method,
usually by using device_lock().
Protect use of pci_error_handlers->reset_notify() by holding the device
lock while calling it.
Note:
- pci_dev_lock() calls device_lock() in addition to blocking user-space
config accesses.
- pci_err_handlers->reset_notify() is used inside
pci_dev_save_and_disable() and pci_dev_restore(). We could hold the
device lock directly in pci_reset_notify(), but we expand the region
since we have several calls following each other.
Without this, ->reset_notify() may race with ->remove() calls, which can be
easily triggered in NVMe.
[bhelgaas: changelog, add pci_reset_notify() comment]
[bhelgaas: fold in fix from Dan Carpenter <dan.carpenter@oracle.com>:
http://lkml.kernel.org/r/20170701135323.x5vaj4e2wcs2mcro@mwanda]
Link: http://lkml.kernel.org/r/20170601111039.8913-2-hch@lst.de
Reported-by: Rakesh Pandit <rakesh@tuxera.com>
Tested-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e788787ef4f9c24aafefc480a8da5f92b914e5e6 upstream.
Certain HP keyboards would keep inputting a character automatically which
is the wake-up key after S3 resume
On some AMD platforms USB host fails to respond (by holding resume-K) to
USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures
that resume is signaled for at least 20 ms (TDRSMDN), which is defined in
USB 2.0 spec. The result is that the keyboard is out of function.
In SNPS USB design, the host responds to the resume request only after
system gets back to S0 and the host gets to functional after the internal
HW restore operation that is more than 1 second after the initial resume
request from the USB device.
As a workaround for specific keyboard ID(HP Keyboards), applying port reset
after resume when the keyboard is plugged in.
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7496cfe5431f21da5d27a8388c326397e3f0a5db upstream.
Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to
connect to Realtek r8153.
The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk
can make it work.
Since another r8153 dongle at my hand does not have the issue, so add
the quirk to the Genesys Logic hub instead.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2eac13624364db5b5e1666ae0bb3a4d36bc56b6e upstream.
While unlink an urb, if the urb has been programmed in the controller,
the controller driver might do some hw related actions to tear down the
urb.
Currently usb_hcd_flush_endpoint() passes each urb from the head of the
endpoint's urb_list to the controller driver, which could make the
controller driver think each urb has been programmed and take the
unnecessary actions for each urb.
This patch changes the behavior in usb_hcd_flush_endpoint() to pass the
urbs from the tail of the list, to avoid any unnecessary actions in an
controller driver.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94c43b9897abf4ea366ed4dba027494e080c7050 upstream.
Some buggy USB disk adapters disconnect and reconnect multiple times
during the enumeration procedure. This may lead to a device
connecting at full speed instead of high speed, because when the USB
stack sees that a device isn't able to enumerate at high speed, it
tries to hand the connection over to a full-speed companion
controller.
The logic for doing this is careful to check that the device is still
connected. But this check is inadequate if the device disconnects and
reconnects before the check is done. The symptom is that a device
works, but much more slowly than it is capable of operating.
The situation was made worse recently by commit 22547c4cc4fe ("usb:
hub: Wait for connection to be reestablished after port reset"), which
increases the delay following a reset before a disconnect is
recognized, thus giving the device more time to reconnect.
This patch makes the check more robust. If the device was
disconnected at any time during enumeration, we will now skip the
full-speed handover.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Zdenek Kabelac <zkabelac@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2acecd58969897795cf015c9057ebd349a3fda8a upstream.
The latest HW manual (Rev.0.55) shows us this UGCTRL2.VBUSSEL bit.
If the bit sets to 1, the VBUS drive is controlled by phy related
registers (called "UCOM Registers" on the manual). Since R-Car Gen3
environment will control VBUS by phy-rcar-gen3-usb2 driver,
the UGCTRL2.VBUSSEL bit should be set to 1. So, this patch fixes
the register's value. Otherwise, even if the ID pin indicates to
peripheral, the R-Car will output USBn_PWEN to 1 when a host driver
is running.
Fixes: de18757e272d ("usb: renesas_usbhs: add R-Car Gen3 power control"
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aca5b9ebd096039657417c321a9252c696b359c2 upstream.
According to the gadget.h, a "complete" function will always be called
with interrupts disabled. However, sometimes usb3_request_done() function
is called with interrupts enabled. So, this function should be held
by spin_lock_irqsave() to disable interruption. Also, this driver has
to call spin_unlock() to avoid spinlock recursion by this driver before
calling usb_gadget_giveback_request().
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Tested-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 260d9f2fc5655a2552701cdd0b909c4466732f19 upstream.
Commit 0cb64249ca500 ("firmware_loader: abort request if wait_for_completion
is interrupted") added via 4.0 added support to abort the fallback mechanism
when a signal was detected and wait_for_completion_interruptible() returned
-ERESTARTSYS -- for instance when a user hits CTRL-C. The abort was overly
*too* effective.
When a child process terminates (successful or not) the signal SIGCHLD can
be sent to the parent process which ran the child in the background and
later triggered a sync request for firmware through a sysfs interface which
relies on the fallback mechanism. This signal in turn can be recieved by the
interruptible wait we constructed on firmware_class and detects it as an
abort *before* userspace could get a chance to write the firmware. Upon
failure -EAGAIN is returned, so userspace is also kept in the dark about
exactly what happened.
We can reproduce the issue with the fw_fallback.sh selftest:
Before this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: error - sync firmware request cancelled due to SIGCHLD
After this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: SIGCHLD on sync ignored as expected
Fix this by making the wait killable -- only killable by SIGKILL (kill -9).
We loose the ability to allow userspace to cancel a write with CTRL-C
(SIGINT), however its been decided the compromise to require SIGKILL is
worth the gains.
Chances of this issue occuring are low due to the number of drivers upstream
exclusively relying on the fallback mechanism for firmware (2 drivers),
however this is observed in the field with custom drivers with sysfs
triggers to load firmware. Only distributions relying on the fallback
mechanism are impacted as well. An example reported issue was on Android,
as follows:
1) Android init (pid=1) fork()s (say pid=42) [this child process is totally
unrelated to firmware loading, it could be sleep 2; for all we care ]
2) Android init (pid=1) does a write() on a (driver custom) sysfs file which
ends up calling request_firmware() kernel side
3) The firmware loading fallback mechanism is used, the request is sent to
userspace and pid 1 waits in the kernel on wait_*
4) before firmware loading completes pid 42 dies (for any reason, even
normal termination)
5) Kernel delivers SIGCHLD to pid=1 to tell it a child has died, which
causes -ERESTARTSYS to be returned from wait_*
6) The kernel's wait aborts and return -EAGAIN for the
request_firmware() caller.
Fixes: 0cb64249ca500 ("firmware_loader: abort request if wait_for_completion is interrupted")
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Martin Fuzzey <mfuzzey@parkeon.com>
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90d41e74a9c36a84e2efbd2a5b8d79299feee6fa upstream.
Fix batched requests from waiting forever on failure.
The firmware API batched requests feature has been broken since the API call
request_firmware_direct() was introduced on commit bba3a87e982ad ("firmware:
Introduce request_firmware_direct()"), added on v3.14 *iff* the firmware
being requested was not present in *certain kernel builds* [0].
When no firmware is found the worker which goes on to finish never informs
waiters queued up of this, so any batched request will stall in what seems
to be forever (MAX_SCHEDULE_TIMEOUT). Sadly, a reboot will also stall, as
the reboot notifier was only designed to kill custom fallback workers. The
issue seems to the user as a type of soft lockup, what *actually* happens
underneath the hood is a wait call which never completes as we failed to
issue a completion on error.
For device drivers with optional firmware schemes (ie, Intel iwlwifi, or
Netronome -- even though it uses request_firmware() and not
request_firmware_direct()), this could mean that when you boot a system with
multiple cards the firmware will seem to never load on the system, or that
the card is just not responsive even the driver initialization. Due to
differences in scheduling possible this should not always trigger --
one would need to to ensure that multiple requests are in place at the
right time for this to work, also release_firmware() must not be called
prior to any other incoming request. The complexity may not be worth
supporting batched requests in the future given the wait mechanism is
only used also for the fallback mechanism. We'll keep it for now and
just fix it.
Its reported that at least with the Intel WiFi cards on one system this
issue was creeping up 50% of the boots [0].
Before this commit batched requests testing revealed:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
Ater this commit batched testing results:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
[0] https://bugzilla.kernel.org/show_bug.cgi?id=195477
Fixes: bba3a87e982ad ("firmware: Introduce request_firmware_direct()"
Reported-by: Nicolas <nbroeking@me.com>
Reported-by: John Ewalt <jewalt@lgsinnovations.com>
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e44565f62a72064e686f7a852137595ec94d78f2 upstream.
The firmware cache mechanism serves two purposes, the secondary purpose is
not well documented nor understood. This fixes a regression with the
secondary purpose of the firmware cache mechanism: batched requests on
successful lookups. Without this fix *any* time a batched request is
triggered, secondary requests for which the batched request mechanism
was designed for will seem to last forver and seem to never return.
This issue is present for all kernel builds possible, and a hard reset
is required.
The firmware cache is used for:
1) Addressing races with file lookups during the suspend/resume cycle
by keeping firmware in memory during the suspend/resume cycle
2) Batched requests for the same file rely only on work from the first file
lookup, which keeps the firmware in memory until the last
release_firmware() is called
Batched requests *only* take effect if secondary requests come in prior to
the first user calling release_firmware(). The devres name used for the
internal firmware cache is used as a hint other pending requests are
ongoing, the firmware buffer data is kept in memory until the last user of
the buffer calls release_firmware(), therefore serializing requests and
delaying the release until all requests are done.
Batched requests wait for a wakup or signal so we can rely on the first file
fetch to write to the pending secondary requests. Commit 5b029624948d
("firmware: do not use fw_lock for fw_state protection") ported the firmware
API to use swait, and in doing so failed to convert complete_all() to
swake_up_all() -- it used swake_up(), loosing the ability for *some* batched
requests to take effect.
We *could* fix this by just using swake_up_all() *but* swait is now known
to be very special use case, so its best to just move away from it. So we
just go back to using completions as before commit 5b029624948d ("firmware:
do not use fw_lock for fw_state protection") given this was using
complete_all().
Without this fix it has been reported plugging in two Intel 6260 Wifi cards
on a system will end up enumerating the two devices only 50% of the time
[0]. The ported swake_up() should have actually handled the case with two
devices, however, *if more than two cards are used* the swake_up() would
not have sufficed. This change is only part of the required fixes for
batched requests. Another fix is provided in the next patch.
This particular change should fix the cases where more than three requests
with the same firmware name is used, otherwise batched requests will wait
for MAX_SCHEDULE_TIMEOUT and just timeout eventually.
Below is a summary of tests triggering batched requests on different
kernel builds.
Before this patch:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL FAIL
request_firmware_direct() FAIL FAIL
request_firmware_nowait(uevent=true) FAIL FAIL
request_firmware_nowait(uevent=false) FAIL FAIL
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL FAIL
request_firmware_direct() FAIL FAIL
request_firmware_nowait(uevent=true) FAIL FAIL
request_firmware_nowait(uevent=false) FAIL FAIL
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL FAIL
request_firmware_direct() FAIL FAIL
request_firmware_nowait(uevent=true) FAIL FAIL
request_firmware_nowait(uevent=false) FAIL FAIL
============================================================================
After this patch:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
[0] https://bugzilla.kernel.org/show_bug.cgi?id=195477
Cc: Ming Lei <ming.lei@redhat.com>
Fixes: 5b029624948d ("firmware: do not use fw_lock for fw_state protection")
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89f23d51defcb94a5026d4b5da13faf4e1150a6f upstream.
Similar to commit d595259fbb7a ("usb-storage: Add ignore-residue quirk for
Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already
present in unusual_uas.h. Both in same controller IC family.
Issue is that MakeMKV fails during key exchange with installed bluray drive
with following error:
002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0'
Signed-off-by: Alan Swanson <reiver@improbability.net>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cef988642cdac44e910a27cb6e8166c96f86a0df upstream.
Comedi's read and write file operation handlers (`comedi_read()` and
`comedi_write()`) currently call `copy_to_user()` or `copy_from_user()`
whilst in the `TASK_INTERRUPTIBLE` state, which falls foul of the
`might_fault()` checks when enabled. Fix it by setting the current task
state back to `TASK_RUNNING` a bit earlier before calling these
functions.
Reported-by: Piotr Gregor <piotrgregor@rsyncme.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
modifications"
commit 631b010abc5b57009c6a8328f51492665f6ef310 upstream.
Inheriting the ADC BIAS current settings from the BIOS instead of
hardcoding then causes the AXP288 to disable charging (I think it
mis-detects an overheated battery) on at least one model tablet.
So lets go back to hard coding the values, this reverts
commit fa2849e9649b ("iio: adc: axp288: Drop bogus
AXP288_ADC_TS_PIN_CTRL register modifications"), fixing charging not
working on the model tablet in question.
The exact cause is not fully understood, hence the revert to a known working
state.
Reported-by: Umberto Ixxo <sfumato1977@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3507e48d3f99a93a3056a34a5365f310434570f upstream.
The TSL2563 driver provides three iio channels, two of which are raw ADC
channels (channel 0 and channel 1) in the device and the remaining one
is calculated by the two. The ADC channel 0 only supports programmable
interrupt with threshold settings and this driver supports the event but
the generated event code does not contain the corresponding iio channel
type.
This is going to change userspace ABI. Hopefully fixing this to be
what it should always have been won't break any userspace code.
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit add6e6ab3ee0e237822e0951476d3df039b49ec8 upstream.
Set multiread variable to false for LPS22HB pressure sensor since
it is already enabled in CTRL_REG2. Previous configuration does not
cause any issue in I2C communication since SUB Msb has no meaning
whereas it breaks register address in SPI communication
Fixes: e039e2f5b4da (iio:st_pressure:initial lps22hb sensor support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e59e18989c68a8d7941005f81ad6abc4ca682de0 upstream.
After probe we would put the device in normal mode, after a runtime
suspend-resume we would put it back in normal mode. But for a regular
suspend-resume we would only put it back in normal mode if triggers
or events have been requested. This is not consistent and breaks
reading raw values after a suspend-resume.
This commit changes the regular resume path to also unconditionally put
the device back in normal mode, fixing reading of raw values not working
after a regular suspend-resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7b8829d242b1a58107e9c02b09e93aec446d55c upstream.
Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration
Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.
Fixes: ddc05fa28606 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 737cc2a593782df6846b3cab7e0f64384f58364a upstream.
This patch enables adc engine at initialization time and waits
for the initial sequence completion before enabling adc channels.
Without this code adc channels are not functional and shows
zeros for all connected channels.
Tested on mellanox msn platform.
v1 -> v2:
Pointed by Rick Altherr:
- Wait init sequence code enabled by bool
from OF match table.
Signed-off-by: Mykola Kostenok <c_mykolak@mellanox.com>
Reviewed-by: Rick Altherr <raltherr@google.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 105967ad68d2eb1a041bc041f9cf96af2a653b65 upstream.
gcc-7 points out an older regression:
drivers/staging/iio/resolver/ad2s1210.c: In function 'ad2s1210_read_raw':
drivers/staging/iio/resolver/ad2s1210.c:515:42: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
The original code had 'unsigned short' here, but incorrectly got
converted to 'bool'. This reverts the regression and uses a normal
type instead.
Fixes: 29148543c521 ("staging:iio:resolver:ad2s1210 minimal chan spec conversion.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd5a6a4fdaba150089af2afc220eae0fef74878a upstream.
Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared
HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for
the primary one.
Among other thigs, this prevents check_root_hub_suspended() from
returning -EBUSY for dead HCDs which helps to work around system
suspend issues in some situations.
This actually fixes occasional suspend failures on one of my test
machines.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45d73860530a14c608f410b91c6c341777bfa85d upstream.
commit 68fe05e2a451 ("usb: musb: fix tx fifo flush handling") drops the
1ms delay trying to solve the long disconnect time issue when
application queued many tx urbs. However, the 1ms delay is needed for
some use cases, for example, without the delay, reconnecting AR9271 WIFI
dongle no longer works if the connection is dropped from the AP.
So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the
long disconnect time problem with a separate patch for
usb_hcd_flush_endpoint().
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b6bcd3d093c698d32e93d4da57679b8fbc5e01e upstream.
This adds a new ATEN device id for a new pl2303-based device.
Reported-by: Peter Kuo <PeterKuo@aten.com.tw>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9585e340db9f6cc1c0928d82c3a23cc4460f0a3f upstream.
The German Telekom offers a ZigBee USB Stick under the brand name Qivicon
for their SmartHome Home Base in its 1. Generation. The productId is not
known by the according kernel module, this patch adds support for it.
Signed-off-by: Stefan Triller <github@stefantriller.de>
Reviewed-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
