summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2013-12-12Input: mousedev - allow disabling even without CONFIG_EXPERTTom Gundersen1-1/+1
commit dfaaed08ecc01bd513248ba7999daf50ce028352 upstream. Moust (if not all) modern software, including X, uses /dev/eventX rather than the legacy /dev/mouseX devices. It therefore makes sense for general-purpose (distro) kernels to use MOUSEDV=m (or even n), so let's drop the EXPERT=y requirement. Signed-off-by: Tom Gundersen <teg@jklm.no> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-12Input: allow deselecting serio drivers even without CONFIG_EXPERTTom Gundersen2-5/+5
commit bcd2623073e98f69f84720308db0b142c4da0bd6 upstream. There is plenty of consumer hardware (e.g., mac books) that does not use AT keyboards or PS/2 mice. It therefore makes sense for distro kernels to build the related drivers as modules to avoid loading them on hardware that does not need them. As such, these options should no longer be protected by EXPERT. Moreover, building these drivers as modules gets rid of the following ugly error during boot: [ 2.337745] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 3.439537] i8042: No controller found Signed-off-by: Tom Gundersen <teg@jklm.no> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-12powerpc/gpio: Fix the wrong GPIO input data on MPC8572/MPC8536Liu Gang1-2/+6
commit 1aeef303b5d9e243c41d5b80f8bb059366514a10 upstream. For MPC8572/MPC8536, the status of GPIOs defined as output cannot be determined by reading GPDAT register, so the code use shadow data register instead. But the code may give the wrong status of GPIOs defined as input under some scenarios: 1. If some pins were configured as inputs and were asserted high before booting the kernel, the shadow data has been initialized with those pin values. 2. Some pins have been configured as output first and have been set to the high value, then reconfigured as input. The above cases will make the shadow data for those input pins to be set to high. Then reading the pin status will always return high even if the actual pin status is low. The code should eliminate the effects of the shadow data to the input pins, and the status of those pins should be read directly from GPDAT. Acked-by: Scott Wood <scottwood@freescale.com> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-12net: smc91: fix crash regression on the versatileLinus Walleij1-18/+4
commit a0c20fb02592d372e744d1d739cda3e1b3defaae upstream. After commit e9e4ea74f06635f2ffc1dffe5ef40c854faa0a90 "net: smc91x: dont't use SMC_outw for fixing up halfword-aligned data" The Versatile SMSC LAN91C111 is crashing like this: ------------[ cut here ]------------ kernel BUG at /home/linus/linux/drivers/net/ethernet/smsc/smc91x.c:599! Internal error: Oops - BUG: 0 [#1] ARM Modules linked in: CPU: 0 PID: 43 Comm: udhcpc Not tainted 3.13.0-rc1+ #24 task: c6ccfaa0 ti: c6cd0000 task.ti: c6cd0000 PC is at smc_hardware_send_pkt+0x198/0x22c LR is at smc_hardware_send_pkt+0x24/0x22c pc : [<c01be324>] lr : [<c01be1b0>] psr: 20000013 sp : c6cd1d08 ip : 00000001 fp : 00000000 r10: c02adb08 r9 : 00000000 r8 : c6ced802 r7 : c786fba0 r6 : 00000146 r5 : c8800000 r4 : c78d6000 r3 : 0000000f r2 : 00000146 r1 : 00000000 r0 : 00000031 Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 0005317f Table: 06cf4000 DAC: 00000015 Process udhcpc (pid: 43, stack limit = 0xc6cd01c0) Stack: (0xc6cd1d08 to 0xc6cd2000) 1d00: 00000010 c8800000 c78d6000 c786fba0 c78d6000 c01be868 1d20: c01be7a4 00004000 00000000 c786fba0 c6c12b80 c0208554 000004d0 c780fc60 1d40: 00000220 c01fb734 00000000 00000000 00000000 c6c9a440 c6c12b80 c78d6000 1d60: c786fba0 c6c9a440 00000000 c021d1d8 00000000 00000000 c6c12b80 c78d6000 1d80: c786fba0 00000001 c6c9a440 c02087f8 c6c9a4a0 00080008 00000000 00000000 1da0: c78d6000 c786fba0 c78d6000 00000138 00000000 00000000 00000000 00000000 1dc0: 00000000 c027ba74 00000138 00000138 00000001 00000010 c6cedc00 00000000 1de0: 00000008 c7404400 c6cd1eec c6cd1f14 c067a73c c065c0b8 00000000 c067a740 1e00: 01ffffff 002040d0 00000000 00000000 00000000 00000000 00000000 ffffffff 1e20: 43004400 00110022 c6cdef20 c027ae8c c6ccfaa0 be82d65c 00000014 be82d3cc 1e40: 00000000 00000000 00000000 c01f2870 00000000 00000000 00000000 c6cd1e88 1e60: c6ccfaa0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1e80: 00000000 00000000 00000031 c7802310 c7802300 00000138 c7404400 c0771da0 1ea0: 00000000 c6cd1eec c7800340 00000138 be82d65c 00000014 be82d3cc c6cd1f08 1ec0: 00000014 00000000 c7404400 c7404400 00000138 c01f4628 c78d6000 00000000 1ee0: 00000000 be82d3cc 00000138 c6cd1f08 00000014 c6cd1ee4 00000001 00000000 1f00: 00000000 00000000 00080011 00000002 06000000 ffffffff 0000ffff 00000002 1f20: 06000000 ffffffff 0000ffff c00928c8 c065c520 c6cd1f58 00000003 c009299c 1f40: 00000003 c065c520 c7404400 00000000 c7404400 c01f2218 c78106b0 c7441cb0 1f60: 00000000 00000006 c06799fc 00000000 00000000 00000006 00000000 c01f3ee0 1f80: 00000000 00000000 be82d678 be82d65c 00000014 00000001 00000122 c00139c8 1fa0: c6cd0000 c0013840 be82d65c 00000014 00000006 be82d3cc 00000138 00000000 1fc0: be82d65c 00000014 00000001 00000122 00000000 00000000 00018cb1 00000000 1fe0: 00003801 be82d3a8 0003a0c7 b6e9af08 60000010 00000006 00000000 00000000 [<c01be324>] (smc_hardware_send_pkt+0x198/0x22c) from [<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8) [<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8) from [<c0208554>] (dev_hard_start_xmit+0x460/0x4cc) [<c0208554>] (dev_hard_start_xmit+0x460/0x4cc) from [<c021d1d8>] (sch_direct_xmit+0x94/0x18c) [<c021d1d8>] (sch_direct_xmit+0x94/0x18c) from [<c02087f8>] (dev_queue_xmit+0x238/0x42c) [<c02087f8>] (dev_queue_xmit+0x238/0x42c) from [<c027ba74>] (packet_sendmsg+0xbe8/0xd28) [<c027ba74>] (packet_sendmsg+0xbe8/0xd28) from [<c01f2870>] (sock_sendmsg+0x84/0xa8) [<c01f2870>] (sock_sendmsg+0x84/0xa8) from [<c01f4628>] (SyS_sendto+0xb8/0xdc) [<c01f4628>] (SyS_sendto+0xb8/0xdc) from [<c0013840>] (ret_fast_syscall+0x0/0x2c) Code: e3130002 1a000001 e3130001 0affffcd (e7f001f2) ---[ end trace 81104fe70e8da7fe ]--- Kernel panic - not syncing: Fatal exception in interrupt This is because the macro operations in smc91x.h defined for Versatile are missing SMC_outsw() as used in this commit. The Versatile needs and uses the same accessors as the other platforms in the first if(...) clause, just switch it to using that and we have one problem less to worry about. This includes a hunk of a patch from Will Deacon fixin the other 32bit platforms as well: Innokom, Ramses, PXA, PCM027. Checkpatch complains about spacing, but I have opted to follow the style of this .h-file. Cc: Russell King <linux@arm.linux.org.uk> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-12SCSI: hpsa: return 0 from driver probe function on success, not 1Stephen M. Cameron1-1/+1
commit 88bf6d62db4393fa03a58bada9d746312d5b496f upstream. A return value of 1 is interpreted as an error. See pci_driver. in local_pci_probe(). If you're wondering how this ever could have worked, it's because it used to be the case that only return values less than zero were interpreted as failure. But even in the current kernel if the driver registers its various entry points with the kernel, and then returns a value which is interpreted as failure, those registrations aren't undone, so the driver still mostly works. However, the driver's remove function wouldn't be called on rmmod, and pci power management functions wouldn't work. In the case of Smart Array, since it has a battery backed cache (or else no cache) even if the driver is not shut down properly as long as there is no outstanding i/o, nothing too bad happens, which is why it took so long to notice. Requesting backport to stable because the change to pci-driver.c which requires driver probe functions to return 0 occurred between 2.6.35 and 2.6.36 (the pci power management breakage) and again between 3.7 and 3.8 (pci_dev->driver getting set to NULL in local_pci_probe() preventing driver remove function from being called on rmmod.) Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-12SCSI: hpsa: do not discard scsi status on aborted commandsStephen M. Cameron1-1/+1
commit 2e311fbabdc23b7eaec77313dc3b9a151a5407b5 upstream. We inadvertantly discarded the scsi status for aborted commands. For some commands (e.g. reads from tape drives) these can't be retried, and if we discarded the scsi status, the scsi mid layer couldn't notice anything was wrong and the error was not reported. Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-12SCSI: libsas: fix usage of ata_tf_to_fisDan Williams1-1/+1
commit ae5fbae0ccd982dfca0ce363036ed92f5b13f150 upstream. Since commit 110dd8f19df5 "[SCSI] libsas: fix scr_read/write users and update the libata documentation" we have been passing pmp=1 and is_cmd=0 to ata_tf_to_fis(). Praveen reports that eSATA attached drives do not discover correctly. His investigation found that the BIOS was passing pmp=0 while Linux was passing pmp=1 and failing to discover the drives. Update libsas to follow the libata example of pulling the pmp setting from the ata_link and correct is_cmd to be 1 since all tf's submitted through ->qc_issue are commands. Presumably libsas lldds do not care about is_cmd as they have sideband mechanisms to perform link management. http://marc.info/?l=linux-scsi&m=138179681726990 [jejb: checkpatch fix] Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reported-by: Praveen Murali <pmurali@logicube.com> Tested-by: Praveen Murali <pmurali@logicube.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-12SCSI: enclosure: fix WARN_ON in dual path device removingJames Bottomley1-0/+7
commit a1470c7bf3a4676e62e4c0fb204e339399eb5c59 upstream. Bug report from: wenxiong@linux.vnet.ibm.com The issue is happened in dual controller configuration. We got the sysfs warnings when rmmod the ipr module. enclosure_unregister() in drivers/msic/enclosure.c, call device_unregister() for each componment deivce, device_unregister() ->device_del()->kobject_del() ->sysfs_remove_dir(). In sysfs_remove_dir(), set kobj->sd = NULL. For each componment device, enclosure_component_release()->enclosure_remove_links()->sysfs_remove_link() in which checking kobj->sd again, it has been set as NULL when doing device_unregister. So we saw all these sysfs WARNING. Tested-by: wenxiong@linux.vnet.ibm.com Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08dm: fix truncated status stringsMikulas Patocka12-101/+85
commit fd7c092e711ebab55b2688d3859d95dfd0301f73 upstream. Avoid returning a truncated table or status string instead of setting the DM_BUFFER_FULL_FLAG when the last target of a table fills the buffer. When processing a table or status request, the function retrieve_status calls ti->type->status. If ti->type->status returns non-zero, retrieve_status assumes that the buffer overflowed and sets DM_BUFFER_FULL_FLAG. However, targets don't return non-zero values from their status method on overflow. Most targets returns always zero. If a buffer overflow happens in a target that is not the last in the table, it gets noticed during the next iteration of the loop in retrieve_status; but if a buffer overflow happens in the last target, it goes unnoticed and erroneously truncated data is returned. In the current code, the targets behave in the following way: * dm-crypt returns -ENOMEM if there is not enough space to store the key, but it returns 0 on all other overflows. * dm-thin returns errors from the status method if a disk error happened. This is incorrect because retrieve_status doesn't check the error code, it assumes that all non-zero values mean buffer overflow. * all the other targets always return 0. This patch changes the ti->type->status function to return void (because most targets don't use the return code). Overflow is detected in retrieve_status: if the status method fills up the remaining space completely, it is assumed that buffer overflow happened. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08iommu/vt-d: Fixed interaction of VFIO_IOMMU_MAP_DMA with IOMMU address limitsJulian Stecklina1-1/+5
commit f9423606ade08653dd8a43334f0a7fb45504c5cc upstream. The BUG_ON in drivers/iommu/intel-iommu.c:785 can be triggered from userspace via VFIO by calling the VFIO_IOMMU_MAP_DMA ioctl on a vfio device with any address beyond the addressing capabilities of the IOMMU. The problem is that the ioctl code calls iommu_iova_to_phys before it calls iommu_map. iommu_map handles the case that it gets addresses beyond the addressing capabilities of its IOMMU. intel_iommu_iova_to_phys does not. This patch fixes iommu_iova_to_phys to return NULL for addresses beyond what the IOMMU can handle. This in turn causes the ioctl call to fail in iommu_map and (correctly) return EFAULT to the user with a helpful warning message in the kernel log. Signed-off-by: Julian Stecklina <jsteckli@os.inf.tu-dresden.de> Acked-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Joerg Roedel <joro@8bytes.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08video: kyro: fix incorrect sizes when copying to userspaceSasha Levin1-3/+3
commit 2ab68ec927310dc488f3403bb48f9e4ad00a9491 upstream. kyro would copy u32s and specify sizeof(unsigned long) as the size to copy. This would copy more data than intended and cause memory corruption and might leak kernel memory. Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08mmc: block: fix a bug of error handling in MMC driverKOBAYASHI Yoshitake1-3/+44
commit c8760069627ad3b0dbbea170f0c4c58b16e18d3d upstream. Current MMC driver doesn't handle generic error (bit19 of device status) in write sequence. As a result, write data gets lost when generic error occurs. For example, a generic error when updating a filesystem management information causes a loss of write data and corrupts the filesystem. In the worst case, the system will never boot. This patch includes the following functionality: 1. To enable error checking for the response of CMD12 and CMD13 in write command sequence 2. To retry write sequence when a generic error occurs Messages are added for v2 to show what occurs. Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08HID: picolcd_core: validate output report detailsKees Cook1-1/+1
commit 1e87a2456b0227ca4ab881e19a11bb99d164e792 upstream. A HID device could send a malicious output report that would cause the picolcd HID driver to trigger a NULL dereference during attr file writing. [jkosina@suse.cz: changed report->maxfield < 1 to report->maxfield != 1 as suggested by Bruno]. CVE-2013-2899 Signed-off-by: Kees Cook <keescook@chromium.org> Cc: stable@kernel.org Reviewed-by: Bruno Prémont <bonbons@linux-vserver.org> Acked-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> [Kefeng: backported to stable 3.4: adjust filename] Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08atm: idt77252: fix dev refcnt leakYing Xue1-1/+1
[ Upstream commit b5de4a22f157ca345cdb3575207bf46402414bc1 ] init_card() calls dev_get_by_name() to get a network deceive. But it doesn't decrease network device reference count after the device is used. Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08net: rework recvmsg handler msg_name and msg_namelen logicHannes Frederic Sowa2-11/+4
[ Upstream commit f3d3342602f8bcbf37d7c46641cb9bca7618eb1c ] This patch now always passes msg->msg_namelen as 0. recvmsg handlers must set msg_namelen to the proper size <= sizeof(struct sockaddr_storage) to return msg_name to the user. This prevents numerous uninitialized memory leaks we had in the recvmsg handlers and makes it harder for new code to accidentally leak uninitialized memory. Optimize for the case recvfrom is called with NULL as address. We don't need to copy the address at all, so set it to NULL before invoking the recvmsg handler. We can do so, because all the recvmsg handlers must cope with the case a plain read() is called on them. read() also sets msg_name to NULL. Also document these changes in include/linux/net.h as suggested by David Miller. Changes since RFC: Set msg->msg_name = NULL if user specified a NULL in msg_name but had a non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't affect sendto as it would bail out earlier while trying to copy-in the address. It also more naturally reflects the logic by the callers of verify_iovec. With this change in place I could remove " if (!uaddr || msg_sys->msg_namelen == 0) msg->msg_name = NULL ". This change does not alter the user visible error logic as we ignore msg_namelen as long as msg_name is NULL. Also remove two unnecessary curly brackets in ___sys_recvmsg and change comments to netdev style. Cc: David Miller <davem@davemloft.net> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08connector: improved unaligned access error fixChris Metcalf1-27/+39
[ Upstream commit 1ca1a4cf59ea343a1a70084fe7cc96f37f3cf5b1 ] In af3e095a1fb4, Erik Jacobsen fixed one type of unaligned access bug for ia64 by converting a 64-bit write to use put_unaligned(). Unfortunately, since gcc will convert a short memset() to a series of appropriately-aligned stores, the problem is now visible again on tilegx, where the memset that zeros out proc_event is converted to three 64-bit stores, causing an unaligned access panic. A better fix for the original problem is to ensure that proc_event is aligned to 8 bytes here. We can do that relatively easily by arranging to start the struct cn_msg aligned to 8 bytes and then offset by 4 bytes. Doing so means that the immediately following proc_event structure is then correctly aligned to 8 bytes. The result is that the memset() stores are now aligned, and as an added benefit, we can remove the put_unaligned() calls in the code. Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08isdnloop: use strlcpy() instead of strcpy()Dan Carpenter1-3/+5
[ Upstream commit f9a23c84486ed350cce7bb1b2828abd1f6658796 ] These strings come from a copy_from_user() and there is no way to be sure they are NUL terminated. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08bonding: fix two race conditions in bond_store_updelay/downdelayNikolay Aleksandrov1-0/+6
[ Upstream commit b869ccfab1e324507fa3596e3e1308444fb68227 ] This patch fixes two race conditions between bond_store_updelay/downdelay and bond_store_miimon which could lead to division by zero as miimon can be set to 0 while either updelay/downdelay are being set and thus miss the zero check in the beginning, the zero div happens because updelay/downdelay are stored as new_value / bond->params.miimon. Use rtnl to synchronize with miimon setting. Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Veaceslav Falico <vfalico@redhat.com> Acked-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08bonding: don't permit to use ARP monitoring in 802.3ad modeVeaceslav Falico1-2/+3
[ Upstream commit ec9f1d15db8185f63a2c3143dc1e90ba18541b08 ] Currently the ARP monitoring is not supported with 802.3ad, and it's prohibited to use it via the module params. However we still can set it afterwards via sysfs, cause we only check for *LB modes there. To fix this - add a check for 802.3ad mode in bonding_store_arp_interval. Signed-off-by: Veaceslav Falico <vfalico@redhat.com> CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04HID: apple: option to swap the 'Option' ("Alt") and 'Command' ("Flag") keys.Nanno Langstraat1-0/+22
commit 43c831468b3d26dbe8f2e061ccaf1abaf9cc1b8b upstream. Use case: people who use both Apple and PC keyboards regularly, and desire to keep&use their PC muscle memory. A particular use case: an Apple compact external keyboard connected to a PC laptop. (This use case can't be covered well by X.org key remappings etc.) Signed-off-by: Nanno Langstraat <langstr@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04HID: roccat: fix Coverity CID 141438Stefan Achatz1-0/+4
commit 7be63f20b00840a6f1c718dcee00855688d64acd upstream. Add missing switch breaks. Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04media: lirc_zilog: Don't use dynamic static allocationMauro Carvalho Chehab1-1/+11
commit ac5b4b6bf0c84c48d7e2e3fce22e35b04282ba76 upstream. Dynamic static allocation is evil, as Kernel stack is too low, and ompilation complains about it on some archs: drivers/staging/media/lirc/lirc_zilog.c:967:1: warning: 'read' uses dynamic stack allocation [enabled by default] Instead, let's enforce a limit for the buffer to be 64. That should be more than enough. Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04Input: i8042 - add PNP modaliasesTom Gundersen1-0/+2
commit 78551277e4df57864b0b0e7f85c23ede2be2edb8 upstream. This allows the module to be autoloaded in the common case. In order to work on non-PnP systems the module should be compiled in or loaded unconditionally at boot (c.f. modules-load.d(5)), as before. Signed-off-by: Tom Gundersen <teg@jklm.no> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04md: fix calculation of stacking limits on level change.NeilBrown1-0/+1
commit 02e5f5c0a0f726e66e3d8506ea1691e344277969 upstream. The various ->run routines of md personalities assume that the 'queue' has been initialised by the blk_set_stacking_limits() call in md_alloc(). However when the level is changed (by level_store()) the ->run routine for the new level is called for an array which has already had the stacking limits modified. This can result in incorrect final settings. So call blk_set_stacking_limits() before ->run in level_store(). A specific consequence of this bug is that it causes discard_granularity to be set incorrectly when reshaping a RAID4 to a RAID0. This is suitable for any -stable kernel since 3.3 in which blk_set_stacking_limits() was introduced. Reported-and-tested-by: "Baldysiak, Pawel" <pawel.baldysiak@intel.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04radeon: workaround pinning failure on low ram gpuJerome Glisse1-0/+28
commit 97b6ff6be9da7675aab339334fda996d6c5077d9 upstream. GPU with low amount of ram can fails at pinning new framebuffer before unpinning old one. On such failure, retry with unpinning old one before pinning new one allowing to work around the issue. This is somewhat ugly but only affect those old GPU we care about. Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04drm/radeon/si: fix define for MC_SEQ_TRAIN_WAKEUP_CNTLAlex Deucher1-1/+1
commit d5693761b2b4ff530c8af8af9ec55b6eae76e617 upstream. Typo in the register offset. Noticed-by: Sylvain BERTRAND <sylware@legeek.net> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04drm/nouveau: when bailing out of a pushbuf ioctl, do not remove previous fenceBen Skeggs1-1/+2
commit 9360bd1112d8874d21942e2ae74f5416b00a8db6 upstream. Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04drm/i915: flush cursors harderDaniel Vetter1-0/+4
commit b2ea8ef559b4d94190009f3651b5b3ab7c05afd3 upstream. Apparently they need the same treatment as primary planes. This fixes modesetting failures because of stuck cursors (!) on Thomas' i830M machine. I've figured while at it I'll also roll it out for the ivb 3 pipe version of this function. I didn't do this for i845/i865 since Bspec says the update mechanism works differently, and there's some additional rules about what can be updated in which order. Tested-by: Thomas Richter <thor@math.tu-berlin.de> Cc: Thomas Richter <thor@math.tu-berlin.de> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04drm/ttm: Handle in-memory region copiesJakob Bornecrantz1-1/+3
commit 9a0599ddeae012a771bba5e23393fc52d8a59d89 upstream. Fix the case where the ttm pointer may be NULL causing a NULL pointer dereference. Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellström <thellstrom@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04prism54: set netdev type to "wlan"Dan Williams1-2/+5
commit 8e3ffa471091c560deb6738ed9ab7445b7a5fd04 upstream. Userspace uses the netdev devtype for stuff like device naming and type detection. Be nice and set it. Remove the pointless #if/#endif around SET_NETDEV_DEV too. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04PCI: Remove duplicate pci_disable_device() from pcie_portdrv_remove()Yinghai Lu1-1/+0
commit e7cc5cf74544d97d7b69e2701595037474db1f96 upstream. The pcie_portdrv .probe() method calls pci_enable_device() once, in pcie_port_device_register(), but the .remove() method calls pci_disable_device() twice, in pcie_port_device_remove() and in pcie_portdrv_remove(). That causes a "disabling already-disabled device" warning when removing a PCIe port device. This happens all the time when removing Thunderbolt devices, but is also easy to reproduce with, e.g., "echo 0000:00:1c.3 > /sys/bus/pci/drivers/pcieport/unbind" This patch removes the disable from pcie_portdrv_remove(). [bhelgaas: changelog, tag for stable] Reported-by: David Bulkow <David.Bulkow@stratus.com> Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04mwifiex: correct packet length for packets from SDIO interfaceAvinash Patil1-0/+3
commit d03b4aa77e1187b77dfe37d14a923547f00baa66 upstream. While receiving a packet on SDIO interface, we allocate skb with size multiple of SDIO block size. We need to resize this skb after RX using packet length from RX header. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04dm: allocate buffer for messages with small number of arguments using GFP_NOIOMikulas Patocka1-2/+16
commit f36afb3957353d2529cb2b00f78fdccd14fc5e9c upstream. dm-mpath and dm-thin must process messages even if some device is suspended, so we allocate argv buffer with GFP_NOIO. These messages have a small fixed number of arguments. On the other hand, dm-switch needs to process bulk data using messages so excessive use of GFP_NOIO could cause trouble. The patch also lowers the default number of arguments from 64 to 8, so that there is smaller load on GFP_NOIO allocations. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Acked-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04rt2400pci: fix RSSI readStanislaw Gruszka1-1/+1
commit 2bf127a5cc372b9319afcbae10b090663b621c8b upstream. RSSI value is provided on word3 not on word2. Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04qeth: avoid buffer overflow in snmp ioctlUrsula Braun1-1/+5
commit 6fb392b1a63ae36c31f62bc3fc8630b49d602b62 upstream. Check user-defined length in snmp ioctl request and allow request only if it fits into a qeth command buffer. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Reviewed-by: Heiko Carstens <heicars2@linux.vnet.ibm.com> Reported-by: Nico Golde <nico@ngolde.de> Reported-by: Fabian Yamaguchi <fabs@goesec.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04rtlwifi: rtl8192cu: Fix incorrect signal strength for unassociated APLarry Finger1-1/+1
commit 78dbfecb95be4635b995af3bd29fa10013409fcd upstream. The routine that processes received frames was returning the RSSI value for the signal strength; however, that value is available only for associated APs. As a result, the strength was the absurd value of 10 dBm. As a result, scans return incorrect values for the strength, which causes unwanted attempts to roam. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04rtlwifi: rtl8192se: Fix incorrect signal strength for unassociated APLarry Finger1-1/+1
commit b4ade797668e33b4e8353c2701ce01d7084dfafa upstream. The routine that processes received frames was returning the RSSI value for the signal strength; however, that value is available only for associated APs. As a result, the strength was the absurd value of 10 dBm. As a result, scans return incorrect values for the strength, which causes unwanted attempts to roam. This patch fixes https://bugzilla.kernel.org/show_bug.cgi?id=63881. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Matthieu Baerts <matttbe@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04rtlwifi: rtl8192de: Fix incorrect signal strength for unassociated APLarry Finger1-1/+1
commit 3545f3d5f4af715c914394123ce7725a9cf0a1c4 upstream. The routine that processes received frames was returning the RSSI value for the signal strength; however, that value is available only for associated APs. As a result, the strength was the absurd value of 10 dBm. As a result, scans return incorrect values for the strength, which causes unwanted attempts to roam. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04staging: vt6656: [BUG] Fix for TX USB resets from vendors driver.Malcolm Priestley2-0/+12
commit 9df682927c2e3a92f43803d6b52095992e3b2ab8 upstream. This fixes resets on heavy TX data traffic. Vendor driver VT6656_Linux_src_v1.21.03_x86_11.04.zip http://www.viaembedded.com/servlet/downloadSvl?id=1890&download_file_id=14704 This is GPL-licensed code. original code BBbVT3184Init ... //2007-0725, RobertChang add, Enable Squelch detect reset option(SQ_RST_Opt), USB (register4, bit1) CONTROLnsRequestIn(pDevice, MESSAGE_TYPE_READ, (WORD)0x600+4, // USB's Reg4's bit1 MESSAGE_REQUEST_MEM, 1, (PBYTE) &byData); byData = byData|2 ; CONTROLnsRequestOut(pDevice, MESSAGE_TYPE_WRITE, (WORD)0x600+4, // USB's Reg4's bit1 MESSAGE_REQUEST_MEM, 1, (PBYTE) &byData); return TRUE;//ntStatus; .... A back port patch is needed for kernels less than 3.10. Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04xen/blkback: fix reference countingVegard Nossum1-1/+2
commit ea5ec76d76da9279d12027c1828544c5ccbe7932 upstream. If the permission check fails, we drop a reference to the blkif without having taken it in the first place. The bug was introduced in commit 604c499cbbcc3d5fe5fb8d53306aa0fae1990109 (xen/blkback: Check device permissions before allowing OP_DISCARD). Cc: Jan Beulich <JBeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04mtd: gpmi: fix kernel BUG due to racing DMA operationsHuang Shijie1-2/+2
commit 7b3d2fb92067bcb29f0f085a9fa9fa64920a6646 upstream. [1] The gpmi uses the nand_command_lp to issue the commands to NAND chips. The gpmi issues a DMA operation with gpmi_cmd_ctrl when it handles a NAND_CMD_NONE control command. So when we read a page(NAND_CMD_READ0) from the NAND, we may send two DMA operations back-to-back. If we do not serialize the two DMA operations, we will meet a bug when 1.1) we enable CONFIG_DMA_API_DEBUG, CONFIG_DMADEVICES_DEBUG, and CONFIG_DEBUG_SG. 1.2) Use the following commands in an UART console and a SSH console: cmd 1: while true;do dd if=/dev/mtd0 of=/dev/null;done cmd 1: while true;do dd if=/dev/mmcblk0 of=/dev/null;done The kernel log shows below: ----------------------------------------------------------------- kernel BUG at lib/scatterlist.c:28! Unable to handle kernel NULL pointer dereference at virtual address 00000000 ......................... [<80044a0c>] (__bug+0x18/0x24) from [<80249b74>] (sg_next+0x48/0x4c) [<80249b74>] (sg_next+0x48/0x4c) from [<80255398>] (debug_dma_unmap_sg+0x170/0x1a4) [<80255398>] (debug_dma_unmap_sg+0x170/0x1a4) from [<8004af58>] (dma_unmap_sg+0x14/0x6c) [<8004af58>] (dma_unmap_sg+0x14/0x6c) from [<8027e594>] (mxs_dma_tasklet+0x18/0x1c) [<8027e594>] (mxs_dma_tasklet+0x18/0x1c) from [<8007d444>] (tasklet_action+0x114/0x164) ----------------------------------------------------------------- 1.3) Assume the two DMA operations is X (first) and Y (second). The root cause of the bug: Assume process P issues DMA X, and sleep on the completion @this->dma_done. X's tasklet callback is dma_irq_callback. It firstly wake up the process sleeping on the completion @this->dma_done, and then trid to unmap the scatterlist S. The waked process P will issue Y in another ARM core. Y initializes S->sg_magic to zero with sg_init_one(), while dma_irq_callback is unmapping S at the same time. See the diagram: ARM core 0 | ARM core 1 ------------------------------------------------------------- (P issues DMA X, then sleep) --> | | (X's tasklet wakes P) --> | | | <-- (P begin to issue DMA Y) | (X's tasklet unmap the | scatterlist S with dma_unmap_sg) --> | <-- (Y calls sg_init_one() to init | scatterlist S) | [2] This patch serialize both the X and Y in the following way: Unmap the DMA scatterlist S firstly, and wake up the process at the end of the DMA callback, in such a way, Y will be executed after X. After this patch: ARM core 0 | ARM core 1 ------------------------------------------------------------- (P issues DMA X, then sleep) --> | | (X's tasklet unmap the | scatterlist S with dma_unmap_sg) --> | | (X's tasklet wakes P) --> | | | <-- (P begin to issue DMA Y) | | <-- (Y calls sg_init_one() to init | scatterlist S) | Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04mtd: nand: hack ONFI for non-power-of-2 dimensionsBrian Norris1-2/+13
commit 4355b70cf48363c50a9de450b01178c83aba8f6a upstream. Some bright specification writers decided to write this in the ONFI spec (from ONFI 3.0, Section 3.1): "The number of blocks and number of pages per block is not required to be a power of two. In the case where one of these values is not a power of two, the corresponding address shall be rounded to an integral number of bits such that it addresses a range up to the subsequent power of two value. The host shall not access upper addresses in a range that is shown as not supported." This breaks every assumption MTD makes about NAND block/chip-size dimensions -- they *must* be a power of two! And of course, an enterprising manufacturer has made use of this lovely freedom. Exhibit A: Micron MT29F32G08CBADAWP "- Plane size: 2 planes x 1064 blocks per plane - Device size: 32Gb: 2128 blockss [sic]" This quickly hits a BUG() in nand_base.c, since the extra dimensions overflow so we think it's a second chip (on my single-chip setup): ONFI param page 0 valid ONFI flash detected NAND device: Manufacturer ID: 0x2c, Chip ID: 0x44 (Micron MT29F32G08CBADAWP), 4256MiB, page size: 8192, OOB size: 744 ------------[ cut here ]------------ kernel BUG at drivers/mtd/nand/nand_base.c:203! Internal error: Oops - BUG: 0 [#1] SMP ARM [... trim ...] [<c02cf3e4>] (nand_select_chip+0x18/0x2c) from [<c02d25c0>] (nand_do_read_ops+0x90/0x424) [<c02d25c0>] (nand_do_read_ops+0x90/0x424) from [<c02d2dd8>] (nand_read+0x54/0x78) [<c02d2dd8>] (nand_read+0x54/0x78) from [<c02ad2c8>] (mtd_read+0x84/0xbc) [<c02ad2c8>] (mtd_read+0x84/0xbc) from [<c02d4b28>] (scan_read.clone.4+0x4c/0x64) [<c02d4b28>] (scan_read.clone.4+0x4c/0x64) from [<c02d4c88>] (search_bbt+0x148/0x290) [<c02d4c88>] (search_bbt+0x148/0x290) from [<c02d4ea4>] (nand_scan_bbt+0xd4/0x5c0) [... trim ...] ---[ end trace 0c9363860d865ff2 ]--- So to fix this, just truncate these dimensions down to the greatest power-of-2 dimension that is less than or equal to the specified dimension. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04loop: fix crash if blk_alloc_queue failsMikulas Patocka1-1/+3
commit 3ec981e30fae1f3c8728a05c730acaa1f627bcfb upstream. loop: fix crash if blk_alloc_queue fails If blk_alloc_queue fails, loop_add cleans up, but it doesn't clean up the identifier allocated with idr_alloc. That causes crash on module unload in idr_for_each(&loop_index_idr, &loop_exit_cb, NULL); where we attempt to remove non-existed device with that id. BUG: unable to handle kernel NULL pointer dereference at 0000000000000380 IP: [<ffffffff812057c9>] del_gendisk+0x19/0x2d0 PGD 43d399067 PUD 43d0ad067 PMD 0 Oops: 0000 [#1] PREEMPT SMP Modules linked in: loop(-) dm_snapshot dm_zero dm_mirror dm_region_hash dm_log dm_loop dm_mod ip6table_filter ip6_tables uvesafb cfbcopyarea cfbimgblt cfbfillrect fbcon font bitblit fbcon_rotate fbcon_cw fbcon_ud fbcon_ccw softcursor fb fbdev msr ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_conntrack_ipv4 nf_defrag_ipv4 xt_state ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp llc tun ipv6 cpufreq_userspace cpufreq_stats cpufreq_ondemand cpufreq_conservative cpufreq_powersave spadfs fuse hid_generic usbhid hid raid0 md_mod dmi_sysfs nf_nat_ftp nf_nat nf_conntrack_ftp nf_conntrack snd_usb_audio snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc lm85 hwmon_vid snd_hwdep snd_usbmidi_lib snd_rawmidi snd soundcore acpi_cpufreq ohci_hcd freq_table tg3 ehci_pci mperf ehci_hcd kvm_amd kvm sata_svw serverworks libphy libata ide_core k10temp usbcore hwmon microcode ptp pcspkr pps_core e100 skge mii usb_common i2c_piix4 floppy evdev rtc_cmos i2c_core processor but! ton unix CPU: 7 PID: 2735 Comm: rmmod Tainted: G W 3.10.15-devel #15 Hardware name: empty empty/S3992-E, BIOS 'V1.06 ' 06/09/2009 task: ffff88043d38e780 ti: ffff88043d21e000 task.ti: ffff88043d21e000 RIP: 0010:[<ffffffff812057c9>] [<ffffffff812057c9>] del_gendisk+0x19/0x2d0 RSP: 0018:ffff88043d21fe10 EFLAGS: 00010282 RAX: ffffffffa05102e0 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff88043ea82800 RDI: 0000000000000000 RBP: ffff88043d21fe48 R08: 0000000000000000 R09: 0000000000000001 R10: 0000000000000001 R11: 0000000000000000 R12: 00000000000000ff R13: 0000000000000080 R14: 0000000000000000 R15: ffff88043ea82800 FS: 00007ff646534700(0000) GS:ffff880447000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000380 CR3: 000000043e9bf000 CR4: 00000000000007e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Stack: ffffffff8100aba4 0000000000000092 ffff88043d21fe48 ffff88043ea82800 00000000000000ff ffff88043d21fe98 0000000000000000 ffff88043d21fe60 ffffffffa05102b4 0000000000000000 ffff88043d21fe70 ffffffffa05102ec Call Trace: [<ffffffff8100aba4>] ? native_sched_clock+0x24/0x80 [<ffffffffa05102b4>] loop_remove+0x14/0x40 [loop] [<ffffffffa05102ec>] loop_exit_cb+0xc/0x10 [loop] [<ffffffff81217b74>] idr_for_each+0x104/0x190 [<ffffffffa05102e0>] ? loop_remove+0x40/0x40 [loop] [<ffffffff8109adc5>] ? trace_hardirqs_on_caller+0x105/0x1d0 [<ffffffffa05135dc>] loop_exit+0x34/0xa58 [loop] [<ffffffff810a98ea>] SyS_delete_module+0x13a/0x260 [<ffffffff81221d5e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff813cff16>] system_call_fastpath+0x1a/0x1f Code: f0 4c 8b 6d f8 c9 c3 66 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 41 56 41 55 4c 8d af 80 00 00 00 41 54 53 48 89 fb 48 83 ec 18 <48> 83 bf 80 03 00 00 00 74 4d e8 98 fe ff ff 31 f6 48 c7 c7 20 RIP [<ffffffff812057c9>] del_gendisk+0x19/0x2d0 RSP <ffff88043d21fe10> CR2: 0000000000000380 ---[ end trace 64ec069ec70f1309 ]--- Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04IB/ipath: Convert ipath_user_sdma_pin_pages() to use get_user_pages_fast()Jan Kara1-6/+1
commit 4adcf7fb6783e354aab38824d803fa8c4f8e8a27 upstream. ipath_user_sdma_queue_pkts() gets called with mmap_sem held for writing. Except for get_user_pages() deep down in ipath_user_sdma_pin_pages() we don't seem to need mmap_sem at all. Even more interestingly the function ipath_user_sdma_queue_pkts() (and also ipath_user_sdma_coalesce() called somewhat later) call copy_from_user() which can hit a page fault and we deadlock on trying to get mmap_sem when handling that fault. So just make ipath_user_sdma_pin_pages() use get_user_pages_fast() and leave mmap_sem locking for mm. This deadlock has actually been observed in the wild when the node is under memory pressure. Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> [ Merged in fix for call to get_user_pages_fast from Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>. - Roland ] Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04iscsi-target: chap auth shouldn't match username with trailing garbageEric Seppanen1-1/+4
commit 86784c6bdeeef78eed94d298be7a8879f6a97ee2 upstream. In iSCSI negotiations with initiator CHAP enabled, usernames with trailing garbage are permitted, because the string comparison only checks the strlen of the configured username. e.g. "usernameXXXXX" will be permitted to match "username". Just check one more byte so the trailing null char is also matched. Signed-off-by: Eric Seppanen <eric@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04iscsi-target: fix extract_param to handle buffer length corner caseEric Seppanen1-1/+1
commit 369653e4fb511928511b0ce81f41c812ff1f28b6 upstream. extract_param() is called with max_length set to the total size of the output buffer. It's not safe to allow a parameter length equal to the buffer size as the terminating null would be written one byte past the end of the output buffer. Signed-off-by: Eric Seppanen <eric@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04ahci: add Marvell 9230 to the AHCI PCI device listSamir Benmendil1-0/+2
commit 6d5278a68a75891db1df5ae1ecf83d288fc58c65 upstream. Tested with a DAWICONTROL DC-624e on 3.10.10 Signed-off-by: Samir Benmendil <samir.benmendil@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-by: Levente Kurusa <levex@linux.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04ahci: disabled FBS prior to issuing software resetxiangliang yu1-0/+16
commit 89dafa20f3daab5b3e0c13d0068a28e8e64e2102 upstream. Tested with Marvell 88se9125, attached with one port mulitplier(5 ports) and one disk, we will get following boot log messages if using current code: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330) ata8.15: Port Multiplier 1.2, 0x1b4b:0x9715 r160, 5 ports, feat 0x1/0x1f ahci 0000:03:00.0: FBS is enabled ata8.00: hard resetting link ata8.00: SATA link down (SStatus 0 SControl 330) ata8.01: hard resetting link ata8.01: SATA link down (SStatus 0 SControl 330) ata8.02: hard resetting link ata8.02: SATA link down (SStatus 0 SControl 330) ata8.03: hard resetting link ata8.03: SATA link up 6.0 Gbps (SStatus 133 SControl 133) ata8.04: hard resetting link ata8.04: failed to resume link (SControl 133) ata8.04: failed to read SCR 0 (Emask=0x40) ata8.04: failed to read SCR 0 (Emask=0x40) ata8.04: failed to read SCR 1 (Emask=0x40) ata8.04: failed to read SCR 0 (Emask=0x40) ata8.03: native sectors (2) is smaller than sectors (976773168) ata8.03: ATA-8: ST3500413AS, JC4B, max UDMA/133 ata8.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata8.03: configured for UDMA/133 ata8.04: failed to IDENTIFY (I/O error, err_mask=0x100) ata8.15: hard resetting link ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330) ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133' ata8.15: PMP revalidation failed (errno=-19) ata8.15: hard resetting link ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330) ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133' ata8.15: PMP revalidation failed (errno=-19) ata8.15: limiting SATA link speed to 3.0 Gbps ata8.15: hard resetting link ata8.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320) ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133' ata8.15: PMP revalidation failed (errno=-19) ata8.15: failed to recover PMP after 5 tries, giving up ata8.15: Port Multiplier detaching ata8.03: disabled ata8.00: disabled ata8: EH complete The reason is that current detection code doesn't follow AHCI spec: First,the port multiplier detection process look like this: ahci_hardreset(link, class, deadline) if (class == ATA_DEV_PMP) { sata_pmp_attach(dev) /* will enable FBS */ sata_pmp_init_links(ap, nr_ports); ata_for_each_link(link, ap, EDGE) { sata_std_hardreset(link, class, deadline); if (link_is_online) /* do soft reset */ ahci_softreset(link, class, deadline); } } But, according to chapter 9.3.9 in AHCI spec: Prior to issuing software reset, software shall clear PxCMD.ST to '0' and then clear PxFBS.EN to '0'. The patch test ok with kernel 3.11.1. tj: Patch white space contaminated, applied manually with trivial updates. Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04rtlwifi: rtl8192cu: Fix more pointer arithmetic errorsLarry Finger2-6/+6
commit eafbdde9c5629bea58df07275c5917eb42afbbe7 upstream. This driver uses a number of macros to get and set various fields in the RX and TX descriptors. To work correctly, a u8 pointer to the descriptor must be used; however, in some cases a descriptor structure pointer is used instead. In addition, a duplicated statement is removed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04rtlwifi: rtl8192se: Fix wrong assignmentFelipe Pena1-1/+1
commit 3aef7dde8dcf09e0124f0a2665845a507331972b upstream. There is a typo in the struct member name on assignment when checking rtlphy->current_chan_bw == HT_CHANNEL_WIDTH_20_40, the check uses pwrgroup_ht40 for bound limit and uses pwrgroup_ht20 when assigning instead. Signed-off-by: Felipe Pena <felipensp@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>