summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2018-02-07spi: imx: do not access registers while clocks disabledStefan Agner1-2/+13
commit d593574aff0ab846136190b1729c151c736727ec upstream. Since clocks are disabled except during message transfer clocks are also disabled when spi_imx_remove gets called. Accessing registers leads to a freeeze at least on a i.MX 6ULL. Enable clocks before disabling accessing the MXC_CSPICTRL register. Fixes: 9e556dcc55774 ("spi: spi-imx: only enable the clocks when we start to transfer a message") Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07usb: uas: unconditionally bring back host after resetOliver Neukum1-4/+3
commit cbeef22fd611c4f47c494b821b2b105b8af970bb upstream. Quoting Hans: If we return 1 from our post_reset handler, then our disconnect handler will be called immediately afterwards. Since pre_reset blocks all scsi requests our disconnect handler will then hang in the scsi_remove_host call. This is esp. bad because our disconnect handler hanging for ever also stops the USB subsys from enumerating any new USB devices, causes commands like lsusb to hang, etc. In practice this happens when unplugging some uas devices because the hub code may see the device as needing a warm-reset and calls usb_reset_device before seeing the disconnect. In this case uas_configure_endpoints fails with -ENODEV. We do not want to print an error for this, so this commit also silences the shost_printk for -ENODEV. ENDQUOTE However, if we do that we better drop any unconditional execution and report to the SCSI subsystem that we have undergone a reset but we are not operational now. Signed-off-by: Oliver Neukum <oneukum@suse.com> Reported-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07usb: f_fs: Prevent gadget unbind if it is already unboundHemant Kumar1-1/+2
commit ce5bf9a50daf2d9078b505aca1cea22e88ecb94a upstream. Upon usb composition switch there is possibility of ep0 file release happening after gadget driver bind. In case of composition switch from adb to a non-adb composition gadget will never gets bound again resulting into failure of usb device enumeration. Fix this issue by checking FFS_FL_BOUND flag and avoid extra gadget driver unbind if it is already done as part of composition switch. This fixes adb reconnection error reported on Android running v4.4 and above kernel versions. Verified on Hikey running vanilla v4.15-rc7 + few out of tree Mali patches. Reviewed-at: https://android-review.googlesource.com/#/c/582632/ Cc: Felipe Balbi <balbi@kernel.org> Cc: Greg KH <gregkh@linux-foundation.org> Cc: Michal Nazarewicz <mina86@mina86.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Dmitry Shmidt <dimitrysh@google.com> Cc: Badhri <badhri@google.com> Cc: Android Kernel Team <kernel-team@android.com> Signed-off-by: Hemant Kumar <hemantk@codeaurora.org> [AmitP: Cherry-picked it from android-4.14 and updated the commit log] Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07USB: serial: simple: add Motorola Tetra driverJohan Hovold2-0/+8
commit 46fe895e22ab3845515ec06b01eaf1282b342e29 upstream. Add new Motorola Tetra (simple) driver for Motorola Solutions TETRA PEI devices. D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0cad ProdID=9011 Rev=24.16 S: Manufacturer=Motorola Solutions Inc. S: Product=Motorola Solutions TETRA PEI interface C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) Note that these devices do not support the CDC SET_CONTROL_LINE_STATE request (for any interface). Reported-by: Max Schulze <max.schulze@posteo.de> Tested-by: Max Schulze <max.schulze@posteo.de> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07USB: serial: io_edgeport: fix possible sleep-in-atomicJia-Ju Bai1-1/+0
commit c7b8f77872c73f69a16528a9eb87afefcccdc18b upstream. According to drivers/usb/serial/io_edgeport.c, the driver may sleep under a spinlock. The function call path is: edge_bulk_in_callback (acquire the spinlock) process_rcvd_data process_rcvd_status change_port_settings send_iosp_ext_cmd write_cmd_usb usb_kill_urb --> may sleep To fix it, the redundant usb_kill_urb() is removed from the error path after usb_submit_urb() fails. This possible bug is found by my static analysis tool (DSAC) and checked by my code review. Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07CDC-ACM: apply quirk for card readerOliver Neukum1-0/+3
commit df1cc78a52491f71d8170d513d0f6f114faa1bda upstream. This devices drops random bytes from messages if you talk to it too fast. Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07USB: cdc-acm: Do not log urb submission errors on disconnectHans de Goede1-1/+1
commit f0386c083c2ce85284dc0b419d7b89c8e567c09f upstream. When disconnected sometimes the cdc-acm driver logs errors like these: [20278.039417] cdc_acm 2-2:2.1: urb 9 failed submission with -19 [20278.042924] cdc_acm 2-2:2.1: urb 10 failed submission with -19 [20278.046449] cdc_acm 2-2:2.1: urb 11 failed submission with -19 [20278.049920] cdc_acm 2-2:2.1: urb 12 failed submission with -19 [20278.053442] cdc_acm 2-2:2.1: urb 13 failed submission with -19 [20278.056915] cdc_acm 2-2:2.1: urb 14 failed submission with -19 [20278.060418] cdc_acm 2-2:2.1: urb 15 failed submission with -19 Silence these by not logging errors when the result is -ENODEV. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07USB: serial: pl2303: new device id for ChilitagGreg Kroah-Hartman2-0/+2
commit d08dd3f3dd2ae351b793fc5b76abdbf0fd317b12 upstream. This adds a new device id for Chilitag devices to the pl2303 driver. Reported-by: "Chu.Mike [朱堅宜]" <Mike-Chu@prolific.com.tw> Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07staging: rtl8188eu: Fix incorrect response to SIOCGIWESSIDLarry Finger1-10/+4
[ Upstream commit b77992d2df9e47144354d1b25328b180afa33442 ] When not associated with an AP, wifi device drivers should respond to the SIOCGIWESSID ioctl with a zero-length string for the SSID, which is the behavior expected by dhcpcd. Currently, this driver returns an error code (-1) from the ioctl call, which causes dhcpcd to assume that the device is not a wireless interface and therefore it fails to work correctly with it thereafter. This problem was reported and tested at https://github.com/lwfinger/rtl8188eu/issues/234. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07usb: gadget: don't dereference g until after it has been null checkedColin Ian King1-2/+5
[ Upstream commit b2fc059fa549fe6881d4c1f8d698b0f50bcd16ec ] Avoid dereferencing pointer g until after g has been sanity null checked; move the assignment of cdev much later when it is required into a more local scope. Detected by CoverityScan, CID#1222135 ("Dereference before null check") Fixes: b785ea7ce662 ("usb: gadget: composite: fix ep->maxburst initialization") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07media: usbtv: add a new usbidIcenowy Zheng1-0/+1
[ Upstream commit 04226916d2360f56d57ad00bc48d2d1854d1e0b0 ] A new usbid of UTV007 is found in a newly bought device. The usbid is 1f71:3301. The ID on the chip is: UTV007 A89029.1 1520L18K1 Both video and audio is tested with the modified usbtv driver. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Lubomir Rintel <lkundrak@v3.sk> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07scsi: ufs: ufshcd: fix potential NULL pointer dereference in ufshcd_config_vregGustavo A. R. Silva1-2/+5
[ Upstream commit 727535903bea924c4f73abb202c4b3e85fff0ca4 ] _vreg_ is being dereferenced before it is null checked, hence there is a potential null pointer dereference. Fix this by moving the pointer dereference after _vreg_ has been null checked. This issue was detected with the help of Coccinelle. Fixes: aa4976130934 ("ufs: Add regulator enable support") Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bitGeert Uytterhoeven1-0/+1
[ Upstream commit 15bfe05c8d6386f1a90e9340d15336e85e32aad6 ] On 64-bit (e.g. powerpc64/allmodconfig): drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit_done': drivers/net/ethernet/xilinx/ll_temac_main.c:633:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] dev_kfree_skb_irq((struct sk_buff *)cur_p->app4); ^ cdmac_bd.app4 is u32, so it is too small to hold a kernel pointer. Note that several other fields in struct cdmac_bd are also too small to hold physical addresses on 64-bit platforms. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07hwmon: (pmbus) Use 64bit math for DIRECT format valuesRobert Lippert1-9/+12
[ Upstream commit bd467e4eababe4c04272c1e646f066db02734c79 ] Power values in the 100s of watt range can easily blow past 32bit math limits when processing everything in microwatts. Use 64bit math instead to avoid these issues on common 32bit ARM BMC platforms. Fixes: 442aba78728e ("hwmon: PMBus device driver") Signed-off-by: Robert Lippert <rlippert@google.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07xen-netfront: remove warning when unloading moduleEduardo Otubo1-0/+18
[ Upstream commit 5b5971df3bc2775107ddad164018a8a8db633b81 ] v2: * Replace busy wait with wait_event()/wake_up_all() * Cannot garantee that at the time xennet_remove is called, the xen_netback state will not be XenbusStateClosed, so added a condition for that * There's a small chance for the xen_netback state is XenbusStateUnknown by the time the xen_netfront switches to Closed, so added a condition for that. When unloading module xen_netfront from guest, dmesg would output warning messages like below: [ 105.236836] xen:grant_table: WARNING: g.e. 0x903 still in use! [ 105.236839] deferring g.e. 0x903 (pfn 0x35805) This problem relies on netfront and netback being out of sync. By the time netfront revokes the g.e.'s netback didn't have enough time to free all of them, hence displaying the warnings on dmesg. The trick here is to make netfront to wait until netback frees all the g.e.'s and only then continue to cleanup for the module removal, and this is done by manipulating both device states. Signed-off-by: Eduardo Otubo <otubo@redhat.com> Acked-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07bcache: check return value of register_shrinkerMichael Lyle1-1/+4
[ Upstream commit 6c4ca1e36cdc1a0a7a84797804b87920ccbebf51 ] register_shrinker is now __must_check, so check it to kill a warning. Caller of bch_btree_cache_alloc in super.c appropriately checks return value so this is fully plumbed through. This V2 fixes checkpatch warnings and improves the commit description, as I was too hasty getting the previous version out. Signed-off-by: Michael Lyle <mlyle@lyle.org> Reviewed-by: Vojtech Pavlik <vojtech@suse.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07igb: Free IRQs when device is hotpluggedLyude Paul1-1/+1
commit 888f22931478a05bc81ceb7295c626e1292bf0ed upstream. Recently I got a Caldigit TS3 Thunderbolt 3 dock, and noticed that upon hotplugging my kernel would immediately crash due to igb: [ 680.825801] kernel BUG at drivers/pci/msi.c:352! [ 680.828388] invalid opcode: 0000 [#1] SMP [ 680.829194] Modules linked in: igb(O) thunderbolt i2c_algo_bit joydev vfat fat btusb btrtl btbcm btintel bluetooth ecdh_generic hp_wmi sparse_keymap rfkill wmi_bmof iTCO_wdt intel_rapl x86_pkg_temp_thermal coretemp crc32_pclmul snd_pcm rtsx_pci_ms mei_me snd_timer memstick snd pcspkr mei soundcore i2c_i801 tpm_tis psmouse shpchp wmi tpm_tis_core tpm video hp_wireless acpi_pad rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci mfd_core xhci_pci xhci_hcd i2c_hid i2c_core [last unloaded: igb] [ 680.831085] CPU: 1 PID: 78 Comm: kworker/u16:1 Tainted: G O 4.15.0-rc3Lyude-Test+ #6 [ 680.831596] Hardware name: HP HP ZBook Studio G4/826B, BIOS P71 Ver. 01.03 06/09/2017 [ 680.832168] Workqueue: kacpi_hotplug acpi_hotplug_work_fn [ 680.832687] RIP: 0010:free_msi_irqs+0x180/0x1b0 [ 680.833271] RSP: 0018:ffffc9000030fbf0 EFLAGS: 00010286 [ 680.833761] RAX: ffff8803405f9c00 RBX: ffff88033e3d2e40 RCX: 000000000000002c [ 680.834278] RDX: 0000000000000000 RSI: 00000000000000ac RDI: ffff880340be2178 [ 680.834832] RBP: 0000000000000000 R08: ffff880340be1ff0 R09: ffff8803405f9c00 [ 680.835342] R10: 0000000000000000 R11: 0000000000000040 R12: ffff88033d63a298 [ 680.835822] R13: ffff88033d63a000 R14: 0000000000000060 R15: ffff880341959000 [ 680.836332] FS: 0000000000000000(0000) GS:ffff88034f440000(0000) knlGS:0000000000000000 [ 680.836817] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 680.837360] CR2: 000055e64044afdf CR3: 0000000001c09002 CR4: 00000000003606e0 [ 680.837954] Call Trace: [ 680.838853] pci_disable_msix+0xce/0xf0 [ 680.839616] igb_reset_interrupt_capability+0x5d/0x60 [igb] [ 680.840278] igb_remove+0x9d/0x110 [igb] [ 680.840764] pci_device_remove+0x36/0xb0 [ 680.841279] device_release_driver_internal+0x157/0x220 [ 680.841739] pci_stop_bus_device+0x7d/0xa0 [ 680.842255] pci_stop_bus_device+0x2b/0xa0 [ 680.842722] pci_stop_bus_device+0x3d/0xa0 [ 680.843189] pci_stop_and_remove_bus_device+0xe/0x20 [ 680.843627] trim_stale_devices+0xf3/0x140 [ 680.844086] trim_stale_devices+0x94/0x140 [ 680.844532] trim_stale_devices+0xa6/0x140 [ 680.845031] ? get_slot_status+0x90/0xc0 [ 680.845536] acpiphp_check_bridge.part.5+0xfe/0x140 [ 680.846021] acpiphp_hotplug_notify+0x175/0x200 [ 680.846581] ? free_bridge+0x100/0x100 [ 680.847113] acpi_device_hotplug+0x8a/0x490 [ 680.847535] acpi_hotplug_work_fn+0x1a/0x30 [ 680.848076] process_one_work+0x182/0x3a0 [ 680.848543] worker_thread+0x2e/0x380 [ 680.848963] ? process_one_work+0x3a0/0x3a0 [ 680.849373] kthread+0x111/0x130 [ 680.849776] ? kthread_create_worker_on_cpu+0x50/0x50 [ 680.850188] ret_from_fork+0x1f/0x30 [ 680.850601] Code: 43 14 85 c0 0f 84 d5 fe ff ff 31 ed eb 0f 83 c5 01 39 6b 14 0f 86 c5 fe ff ff 8b 7b 10 01 ef e8 b7 e4 d2 ff 48 83 78 70 00 74 e3 <0f> 0b 49 8d b5 a0 00 00 00 e8 62 6f d3 ff e9 c7 fe ff ff 48 8b [ 680.851497] RIP: free_msi_irqs+0x180/0x1b0 RSP: ffffc9000030fbf0 As it turns out, normally the freeing of IRQs that would fix this is called inside of the scope of __igb_close(). However, since the device is already gone by the point we try to unregister the netdevice from the driver due to a hotplug we end up seeing that the netif isn't present and thus, forget to free any of the device IRQs. So: make sure that if we're in the process of dismantling the netdev, we always allow __igb_close() to be called so that IRQs may be freed normally. Additionally, only allow igb_close() to be called from __igb_close() if it hasn't already been called for the given adapter. Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: 9474933caf21 ("igb: close/suspend race in netif_device_detach") Cc: Todd Fujinaka <todd.fujinaka@intel.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07gpio: iop: add missing MODULE_DESCRIPTION/AUTHOR/LICENSEJesse Chan1-0/+4
commit 97b03136e1b637d7a9d2274c099e44ecf23f1103 upstream. This change resolves a new compile-time warning when built as a loadable module: WARNING: modpost: missing MODULE_LICENSE() in drivers/gpio/gpio-iop.o see include/linux/module.h for more information This adds the license as "GPL", which matches the header of the file. MODULE_DESCRIPTION and MODULE_AUTHOR are also added. Signed-off-by: Jesse Chan <jc@linux.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07loop: fix concurrent lo_open/lo_releaseLinus Torvalds1-2/+8
commit ae6650163c66a7eff1acd6eb8b0f752dcfa8eba5 upstream. 范龙飞 reports that KASAN can report a use-after-free in __lock_acquire. The reason is due to insufficient serialization in lo_release(), which will continue to use the loop device even after it has decremented the lo_refcnt to zero. In the meantime, another process can come in, open the loop device again as it is being shut down. Confusion ensues. Reported-by: 范龙飞 <long7573@126.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-07Input: do not emit unneeded EV_SYN when suspendingDmitry Torokhov1-1/+4
commit 00159f19a5057cb779146afce1cceede692af346 upstream. Do not emit EV_SYN/SYN_REPORT on suspend if there were no keys that are still pressed as we are suspending the device (and in all other cases when input core is forcibly releasing keys via input_dev_release_keys() call). Reviewed-by: Benson Leung <bleung@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Bo Hu <bohu@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31vmxnet3: repair memory leakNeil Horman1-1/+1
[ Upstream commit 848b159835ddef99cc4193083f7e786c3992f580 ] with the introduction of commit b0eb57cb97e7837ebb746404c2c58c6f536f23fa, it appears that rq->buf_info is improperly handled. While it is heap allocated when an rx queue is setup, and freed when torn down, an old line of code in vmxnet3_rq_destroy was not properly removed, leading to rq->buf_info[0] being set to NULL prior to its being freed, causing a memory leak, which eventually exhausts the system on repeated create/destroy operations (for example, when the mtu of a vmxnet3 interface is changed frequently. Fix is pretty straight forward, just move the NULL set to after the free. Tested by myself with successful results Applies to net, and should likely be queued for stable, please Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-By: boyang@redhat.com CC: boyang@redhat.com CC: Shrikrishna Khare <skhare@vmware.com> CC: "VMware, Inc." <pv-drivers@vmware.com> CC: David S. Miller <davem@davemloft.net> Acked-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31pppoe: take ->needed_headroom of lower device into account on xmitGuillaume Nault1-5/+6
[ Upstream commit 02612bb05e51df8489db5e94d0cf8d1c81f87b0c ] In pppoe_sendmsg(), reserving dev->hard_header_len bytes of headroom was probably fine before the introduction of ->needed_headroom in commit f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom"). But now, virtual devices typically advertise the size of their overhead in dev->needed_headroom, so we must also take it into account in skb_reserve(). Allocation size of skb is also updated to take dev->needed_tailroom into account and replace the arbitrary 32 bytes with the real size of a PPPoE header. This issue was discovered by syzbot, who connected a pppoe socket to a gre device which had dev->header_ops->create == ipgre_header and dev->hard_header_len == 0. Therefore, PPPoE didn't reserve any headroom, and dev_hard_header() crashed when ipgre_header() tried to prepend its header to skb->data. skbuff: skb_under_panic: text:000000001d390b3a len:31 put:24 head:00000000d8ed776f data:000000008150e823 tail:0x7 end:0xc0 dev:gre0 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:104! invalid opcode: 0000 [#1] SMP KASAN Dumping ftrace buffer: (ftrace buffer empty) Modules linked in: CPU: 1 PID: 3670 Comm: syzkaller801466 Not tainted 4.15.0-rc7-next-20180115+ #97 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:skb_panic+0x162/0x1f0 net/core/skbuff.c:100 RSP: 0018:ffff8801d9bd7840 EFLAGS: 00010282 RAX: 0000000000000083 RBX: ffff8801d4f083c0 RCX: 0000000000000000 RDX: 0000000000000083 RSI: 1ffff1003b37ae92 RDI: ffffed003b37aefc RBP: ffff8801d9bd78a8 R08: 1ffff1003b37ae8a R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff86200de0 R13: ffffffff84a981ad R14: 0000000000000018 R15: ffff8801d2d34180 FS: 00000000019c4880(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000208bc000 CR3: 00000001d9111001 CR4: 00000000001606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: skb_under_panic net/core/skbuff.c:114 [inline] skb_push+0xce/0xf0 net/core/skbuff.c:1714 ipgre_header+0x6d/0x4e0 net/ipv4/ip_gre.c:879 dev_hard_header include/linux/netdevice.h:2723 [inline] pppoe_sendmsg+0x58e/0x8b0 drivers/net/ppp/pppoe.c:890 sock_sendmsg_nosec net/socket.c:630 [inline] sock_sendmsg+0xca/0x110 net/socket.c:640 sock_write_iter+0x31a/0x5d0 net/socket.c:909 call_write_iter include/linux/fs.h:1775 [inline] do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653 do_iter_write+0x154/0x540 fs/read_write.c:932 vfs_writev+0x18a/0x340 fs/read_write.c:977 do_writev+0xfc/0x2a0 fs/read_write.c:1012 SYSC_writev fs/read_write.c:1085 [inline] SyS_writev+0x27/0x30 fs/read_write.c:1082 entry_SYSCALL_64_fastpath+0x29/0xa0 Admittedly PPPoE shouldn't be allowed to run on non Ethernet-like interfaces, but reserving space for ->needed_headroom is a more fundamental issue that needs to be addressed first. Same problem exists for __pppoe_xmit(), which also needs to take dev->needed_headroom into account in skb_cow_head(). Fixes: f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom") Reported-by: syzbot+ed0838d0fa4c4f2b528e20286e6dc63effc7c14d@syzkaller.appspotmail.com Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31scsi: libiscsi: fix shifting of DID_REQUEUE host byteJohannes Thumshirn1-1/+1
commit eef9ffdf9cd39b2986367bc8395e2772bc1284ba upstream. The SCSI host byte should be shifted left by 16 in order to have scsi_decide_disposition() do the right thing (.i.e. requeue the command). Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Fixes: 661134ad3765 ("[SCSI] libiscsi, bnx2i: make bound ep check common") Cc: Lee Duncan <lduncan@suse.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Bart Van Assche <Bart.VanAssche@sandisk.com> Cc: Chris Leech <cleech@redhat.com> Acked-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31dm thin metadata: THIN_MAX_CONCURRENT_LOCKS should be 6Dennis Yang1-1/+5
commit 490ae017f54e55bde382d45ea24bddfb6d1a0aaf upstream. For btree removal, there is a corner case that a single thread could takes 6 locks which is more than THIN_MAX_CONCURRENT_LOCKS(5) and leads to deadlock. A btree removal might eventually call rebalance_children()->rebalance3() to rebalance entries of three neighbor child nodes when shadow_spine has already acquired two write locks. In rebalance3(), it tries to shadow and acquire the write locks of all three child nodes. However, shadowing a child node requires acquiring a read lock of the original child node and a write lock of the new block. Although the read lock will be released after block shadowing, shadowing the third child node in rebalance3() could still take the sixth lock. (2 write locks for shadow_spine + 2 write locks for the first two child nodes's shadow + 1 write lock for the last child node's shadow + 1 read lock for the last child node) Signed-off-by: Dennis Yang <dennisyang@qnap.com> Acked-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31dm btree: fix serious bug in btree_split_beneath()Joe Thornber1-17/+2
commit bc68d0a43560e950850fc69b58f0f8254b28f6d6 upstream. When inserting a new key/value pair into a btree we walk down the spine of btree nodes performing the following 2 operations: i) space for a new entry ii) adjusting the first key entry if the new key is lower than any in the node. If the _root_ node is full, the function btree_split_beneath() allocates 2 new nodes, and redistibutes the root nodes entries between them. The root node is left with 2 entries corresponding to the 2 new nodes. btree_split_beneath() then adjusts the spine to point to one of the two new children. This means the first key is never adjusted if the new key was lower, ie. operation (ii) gets missed out. This can result in the new key being 'lost' for a period; until another low valued key is inserted that will uncover it. This is a serious bug, and quite hard to make trigger in normal use. A reproducing test case ("thin create devices-in-reverse-order") is available as part of the thin-provision-tools project: https://github.com/jthornber/thin-provisioning-tools/blob/master/functional-tests/device-mapper/dm-tests.scm#L593 Fix the issue by changing btree_split_beneath() so it no longer adjusts the spine. Instead it unlocks both the new nodes, and lets the main loop in btree_insert_raw() relock the appropriate one and make any neccessary adjustments. Reported-by: Monty Pavel <monty_pavel@sina.com> Signed-off-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31phy: work around 'phys' references to usb-nop-xceiv devicesArnd Bergmann1-0/+4
commit b7563e2796f8b23c98afcfea7363194227fa089d upstream. Stefan Wahren reports a problem with a warning fix that was merged for v4.15: we had lots of device nodes with a 'phys' property pointing to a device node that is not compliant with the binding documented in Documentation/devicetree/bindings/phy/phy-bindings.txt This generally works because USB HCD drivers that support both the generic phy subsystem and the older usb-phy subsystem ignore most errors from phy_get() and related calls and then use the usb-phy driver instead. However, it turns out that making the usb-nop-xceiv device compatible with the generic-phy binding changes the phy_get() return code from -EINVAL to -EPROBE_DEFER, and the dwc2 usb controller driver for bcm2835 now returns -EPROBE_DEFER from its probe function rather than ignoring the failure, breaking all USB support on raspberry-pi when CONFIG_GENERIC_PHY is enabled. The same code is used in the dwc3 driver and the usb_add_hcd() function, so a reasonable assumption would be that many other platforms are affected as well. I have reviewed all the related patches and concluded that "usb-nop-xceiv" is the only USB phy that is affected by the change, and since it is by far the most commonly referenced phy, all the other USB phy drivers appear to be used in ways that are are either safe in DT (they don't use the 'phys' property), or in the driver (they already ignore -EPROBE_DEFER from generic-phy when usb-phy is available). To work around the problem, this adds a special case to _of_phy_get() so we ignore any PHY node that is compatible with "usb-nop-xceiv", as we know that this can never load no matter how much we defer. In the future, we might implement a generic-phy driver for "usb-nop-xceiv" and then remove this workaround. Since we generally want older kernels to also want to work with the fixed devicetree files, it would be good to backport the patch into stable kernels as well (3.13+ are possibly affected), even though they don't contain any of the patches that may have caused regressions. Fixes: 014d6da6cb25 ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells Fixes: c5bbf358b790 arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv Fixes: 44e5dced2ef6 arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv Fixes: f568f6f554b8 ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv Fixes: d745d5f277bf ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv Fixes: 915fbe59cbf2 ARM: dts: imx: Add missing #phy-cells to usb-nop-xceiv Link: https://marc.info/?l=linux-usb&m=151518314314753&w=2 Link: https://patchwork.kernel.org/patch/10158145/ Cc: Felipe Balbi <balbi@kernel.org> Cc: Eric Anholt <eric@anholt.net> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Rob Herring <robh@kernel.org> Tested-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31Input: twl4030-vibra - fix sibling-node lookupJohan Hovold1-2/+4
commit 5b189201993ab03001a398de731045bfea90c689 upstream. A helper purported to look up a child node based on its name was using the wrong of-helper and ended up prematurely freeing the parent of-node while searching the whole device tree depth-first starting at the parent node. Fixes: 64b9e4d803b1 ("input: twl4030-vibra: Support for DT booted kernel") Fixes: e661d0a04462 ("Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31Input: twl4030-vibra - fix ERROR: Bad of_node_put() warningMarek Belisko1-1/+2
commit e661d0a04462dd98667f8947141bd8defab5b34a upstream. Fix following: [ 8.862274] ERROR: Bad of_node_put() on /ocp/i2c@48070000/twl@48/audio [ 8.869293] CPU: 0 PID: 1003 Comm: modprobe Not tainted 4.2.0-rc2-letux+ #1175 [ 8.876922] Hardware name: Generic OMAP36xx (Flattened Device Tree) [ 8.883514] [<c00159e0>] (unwind_backtrace) from [<c0012488>] (show_stack+0x10/0x14) [ 8.891693] [<c0012488>] (show_stack) from [<c05cb810>] (dump_stack+0x78/0x94) [ 8.899322] [<c05cb810>] (dump_stack) from [<c02cfd5c>] (kobject_release+0x68/0x7c) [ 8.907409] [<c02cfd5c>] (kobject_release) from [<bf0040c4>] (twl4030_vibra_probe+0x74/0x188 [twl4030_vibra]) [ 8.917877] [<bf0040c4>] (twl4030_vibra_probe [twl4030_vibra]) from [<c03816ac>] (platform_drv_probe+0x48/0x90) [ 8.928497] [<c03816ac>] (platform_drv_probe) from [<c037feb4>] (really_probe+0xd4/0x238) [ 8.937103] [<c037feb4>] (really_probe) from [<c0380160>] (driver_probe_device+0x30/0x48) [ 8.945678] [<c0380160>] (driver_probe_device) from [<c03801e0>] (__driver_attach+0x68/0x8c) [ 8.954589] [<c03801e0>] (__driver_attach) from [<c037ea60>] (bus_for_each_dev+0x50/0x84) [ 8.963226] [<c037ea60>] (bus_for_each_dev) from [<c037f828>] (bus_add_driver+0xcc/0x1e4) [ 8.971832] [<c037f828>] (bus_add_driver) from [<c0380b60>] (driver_register+0x9c/0xe0) [ 8.980255] [<c0380b60>] (driver_register) from [<c00097e0>] (do_one_initcall+0x100/0x1b8) [ 8.988983] [<c00097e0>] (do_one_initcall) from [<c00b8008>] (do_init_module+0x58/0x1c0) [ 8.997497] [<c00b8008>] (do_init_module) from [<c00b8cac>] (SyS_init_module+0x54/0x64) [ 9.005950] [<c00b8cac>] (SyS_init_module) from [<c000ed20>] (ret_fast_syscall+0x0/0x54) [ 9.015838] input: twl4030:vibrator as /devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:audio/input/input2 node passed to of_find_node_by_name is put inside that function and new node is returned if found. Free returned node not already freed node. Signed-off-by: Marek Belisko <marek@goldelico.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31Input: twl6040-vibra - fix child-node lookupJohan Hovold1-2/+1
commit dcaf12a8b0bbdbfcfa2be8dff2c4948d9844b4ad upstream. Fix child-node lookup during probe, which ended up searching the whole device tree depth-first starting at parent rather than just matching on its children. Later sanity checks on node properties (which would likely be missing) should prevent this from causing much trouble however, especially as the original premature free of the parent node has already been fixed separately (but that "fix" was apparently never backported to stable). Fixes: e7ec014a47e4 ("Input: twl6040-vibra - update for device tree support") Fixes: c52c545ead97 ("Input: twl6040-vibra - fix DT node memory management") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: H. Nikolaus Schaller <hns@goldelico.com> (on Pyra OMAP5 hardware) Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31Input: twl6040-vibra - fix DT node memory managementH. Nikolaus Schaller1-0/+1
commit c52c545ead97fcc2f4f8ea38f1ae3c23211e09a8 upstream. commit e7ec014a47e4 ("Input: twl6040-vibra - update for device tree support") made the separate vibra DT node to a subnode of the twl6040. It now calls of_find_node_by_name() to locate the "vibra" subnode. This function has a side effect to call of_node_put on() for the twl6040 parent node passed in as a parameter. This causes trouble later on. Solution: we must call of_node_get() before of_find_node_by_name() Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31Input: 88pm860x-ts - fix child-node lookupJohan Hovold1-4/+12
commit 906bf7daa0618d0ef39f4872ca42218c29a3631f upstream. Fix child node-lookup during probe, which ended up searching the whole device tree depth-first starting at parent rather than just matching on its children. To make things worse, the parent node was prematurely freed, while the child node was leaked. Fixes: 2e57d56747e6 ("mfd: 88pm860x: Device tree support") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-31scsi: sg: disable SET_FORCE_LOW_DMAHannes Reinecke1-21/+9
commit 745dfa0d8ec26b24f3304459ff6e9eacc5c8351b upstream. The ioctl SET_FORCE_LOW_DMA has never worked since the initial git check-in, and the respective setting is nowadays handled correctly. So disable it entirely. Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Tested-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17e1000e: Fix e1000_check_for_copper_link_ich8lan return value.Benjamin Poirier1-3/+8
commit 4110e02eb45ea447ec6f5459c9934de0a273fb91 upstream. e1000e_check_for_copper_link() and e1000_check_for_copper_link_ich8lan() are the two functions that may be assigned to mac.ops.check_for_link when phy.media_type == e1000_media_type_copper. Commit 19110cfbb34d ("e1000e: Separate signaling for link check/link up") changed the meaning of the return value of check_for_link for copper media but only adjusted the first function. This patch adjusts the second function likewise. Reported-by: Christian Hesse <list@eworm.de> Reported-by: Gabriel C <nix.or.die@gmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=198047 Fixes: 19110cfbb34d ("e1000e: Separate signaling for link check/link up") Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Tested-by: Christian Hesse <list@eworm.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17uas: ignore UAS for Norelsys NS1068(X) chipsIcenowy Zheng1-0/+7
commit 928afc85270753657b5543e052cc270c279a3fe9 upstream. The UAS mode of Norelsys NS1068(X) is reported to fail to work on several platforms with the following error message: xhci-hcd xhci-hcd.0.auto: ERROR Transfer event for unknown stream ring slot 1 ep 8 xhci-hcd xhci-hcd.0.auto: @00000000bf04a400 00000000 00000000 1b000000 01098001 And when trying to mount a partition on the disk the disk will disconnect from the USB controller, then after re-connecting the device will be offlined and not working at all. Falling back to USB mass storage can solve this problem, so ignore UAS function of this chip. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17staging: android: ashmem: fix a race condition in ASHMEM_SET_SIZE ioctlViktor Slavkovic1-0/+2
commit 443064cb0b1fb4569fe0a71209da7625129fb760 upstream. A lock-unlock is missing in ASHMEM_SET_SIZE ioctl which can result in a race condition when mmap is called. After the !asma->file check, before setting asma->size, asma->file can be set in mmap. That would result in having different asma->size than the mapped memory size. Combined with ASHMEM_UNPIN ioctl and shrinker invocation, this can result in memory corruption. Signed-off-by: Viktor Slavkovic <viktors@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17usbip: remove kernel addresses from usb device and urb debug msgsShuah Khan1-14/+3
commit e1346fd87c71a1f61de1fe476ec8df1425ac931c upstream. usbip_dump_usb_device() and usbip_dump_urb() print kernel addresses. Remove kernel addresses from usb device and urb debug msgs and improve the message content. Instead of printing parent device and bus addresses, print parent device and bus names. Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17USB: fix usbmon BUG triggerPete Zaitcev1-1/+7
commit 46eb14a6e1585d99c1b9f58d0e7389082a5f466b upstream. Automated tests triggered this by opening usbmon and accessing the mmap while simultaneously resizing the buffers. This bug was with us since 2006, because typically applications only size the buffers once and thus avoid racing. Reported by Kirill A. Shutemov. Reported-by: <syzbot+f9831b881b3e849829fc@syzkaller.appspotmail.com> Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17usb: misc: usb3503: make sure reset is low for at least 100usStefan Agner1-0/+2
commit b8626f1dc29d3eee444bfaa92146ec7b291ef41c upstream. When using a GPIO which is high by default, and initialize the driver in USB Hub mode, initialization fails with: [ 111.757794] usb3503 0-0008: SP_ILOCK failed (-5) The reason seems to be that the chip is not properly reset. Probe does initialize reset low, however some lines later the code already set it back high, which is not long enouth. Make sure reset is asserted for at least 100us by inserting a delay after initializing the reset pin during probe. Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17USB: serial: cp210x: add new device ID ELV ALC 8xxxChristian Holl1-0/+1
commit d14ac576d10f865970bb1324d337e5e24d79aaf4 upstream. This adds the ELV ALC 8xxx Battery Charging device to the list of USB IDs of drivers/usb/serial/cp210x.c Signed-off-by: Christian Holl <cyborgx1@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17USB: serial: cp210x: add IDs for LifeScan OneTouch Verio IQDiego Elio Pettenò1-0/+1
commit 4307413256ac1e09b8f53e8715af3df9e49beec3 upstream. Add IDs for the OneTouch Verio IQ that comes with an embedded USB-to-serial converter. Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17Revert "can: kvaser_usb: free buf in error paths"Greg Kroah-Hartman1-2/+0
This reverts commit 70d9dccf50152b0d7bfb2697d8c51e9fab9f782c which was commit 435019b48033138581a6171093b181fc6b4d3d30 upstream. Jimmy Assarsson asks that it be reverted as it's not correct there. Reported-by: Jimmy Assarsson <jimmyassarsson@gmail.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17target: Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASKNicholas Bellinger2-0/+11
commit 1c21a48055a67ceb693e9c2587824a8de60a217c upstream. This patch fixes bug where early se_cmd exceptions that occur before backend execution can result in use-after-free if/when a subsequent ABORT_TASK occurs for the same tag. Since an early se_cmd exception will have had se_cmd added to se_session->sess_cmd_list via target_get_sess_cmd(), it will not have CMD_T_COMPLETE set by the usual target_complete_cmd() backend completion path. This causes a subsequent ABORT_TASK + __target_check_io_state() to signal ABORT_TASK should proceed. As core_tmr_abort_task() executes, it will bring the outstanding se_cmd->cmd_kref count down to zero releasing se_cmd, after se_cmd has already been queued with error status into fabric driver response path code. To address this bug, introduce a CMD_T_PRE_EXECUTE bit that is set at target_get_sess_cmd() time, and cleared immediately before backend driver dispatch in target_execute_cmd() once CMD_T_ACTIVE is set. Then, check CMD_T_PRE_EXECUTE within __target_check_io_state() to determine when an early exception has occured, and avoid aborting this se_cmd since it will have already been queued into fabric driver response path code. Reported-by: Donald White <dew@datera.io> Cc: Donald White <dew@datera.io> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17iscsi-target: Make TASK_REASSIGN use proper se_cmd->cmd_krefNicholas Bellinger1-14/+7
commit ae072726f6109bb1c94841d6fb3a82dde298ea85 upstream. Since commit 59b6986dbf fixed a potential NULL pointer dereference by allocating a se_tmr_req for ISCSI_TM_FUNC_TASK_REASSIGN, the se_tmr_req is currently leaked by iscsit_free_cmd() because no iscsi_cmd->se_cmd.se_tfo was associated. To address this, treat ISCSI_TM_FUNC_TASK_REASSIGN like any other TMR and call transport_init_se_cmd() + target_get_sess_cmd() to setup iscsi_cmd->se_cmd.se_tfo with se_cmd->cmd_kref of 2. This will ensure normal release operation once se_cmd->cmd_kref reaches zero and target_release_cmd_kref() is invoked, se_tmr_req will be released via existing target_free_cmd_mem() and core_tmr_release_req() code. Reported-by: Donald White <dew@datera.io> Cc: Donald White <dew@datera.io> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17net: stmmac: enable EEE in MII, GMII or RGMII onlyJerome Brunet1-0/+6
[ Upstream commit 879626e3a52630316d817cbda7cec9a5446d1d82 ] Note in the databook - Section 4.4 - EEE : " The EEE feature is not supported when the MAC is configured to use the TBI, RTBI, SMII, RMII or SGMII single PHY interface. Even if the MAC supports multiple PHY interfaces, you should activate the EEE mode only when the MAC is operating with GMII, MII, or RGMII interface." Applying this restriction solves a stability issue observed on Amlogic gxl platforms operating with RMII interface and the internal PHY. Fixes: 83bf79b6bb64 ("stmmac: disable at run-time the EEE if not supported") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17sh_eth: fix SH7757 GEther initializationSergei Shtylyov1-2/+2
[ Upstream commit 5133550296d43236439494aa955bfb765a89f615 ] Renesas SH7757 has 2 Fast and 2 Gigabit Ether controllers, while the 'sh_eth' driver can only reset and initialize TSU of the first controller pair. Shimoda-san tried to solve that adding the 'needs_init' member to the 'struct sh_eth_plat_data', however the platform code still never sets this flag. I think that we can infer this information from the 'devno' variable (set to 'platform_device::id') and reset/init the Ether controller pair only for an even 'devno'; therefore 'sh_eth_plat_data::needs_init' can be removed... Fixes: 150647fb2c31 ("net: sh_eth: change the condition of initialization") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17sh_eth: fix TSU resource handlingSergei Shtylyov1-3/+22
[ Upstream commit dfe8266b8dd10e12a731c985b725fcf7f0e537f0 ] When switching the driver to the managed device API, I managed to break the case of a dual Ether devices sharing a single TSU: the 2nd Ether port wouldn't probe. Iwamatsu-san has tried to fix this but his patch was buggy and he then dropped the ball... The solution is to limit calling devm_request_mem_region() to the first of the two ports sharing the same TSU, so devm_ioremap_resource() can't be used anymore for the TSU resource... Fixes: d5e07e69218f ("sh_eth: use managed device API") Reported-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17IB/srpt: Disable RDMA access by the initiatorBart Van Assche1-2/+1
commit bec40c26041de61162f7be9d2ce548c756ce0f65 upstream. With the SRP protocol all RDMA operations are initiated by the target. Since no RDMA operations are initiated by the initiator, do not grant the initiator permission to submit RDMA reads or writes to the target. Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17can: gs_usb: fix return value of the "set_bittiming" callbackWolfgang Grandegger1-1/+1
commit d5b42e6607661b198d8b26a0c30969605b1bf5c7 upstream. The "set_bittiming" callback treats a positive return value as error! For that reason "can_changelink()" will quit silently after setting the bittiming values without processing ctrlmode, restart-ms, etc. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17Input: elantech - add new icbody type 15Aaron Ma1-1/+1
commit 10d900303f1c3a821eb0bef4e7b7ece16768fba4 upstream. The touchpad of Lenovo Thinkpad L480 reports it's version as 15. Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17crypto: n2 - cure use after freeJan Engelhardt1-0/+3
commit 203f45003a3d03eea8fa28d74cfc74c354416fdb upstream. queue_cache_init is first called for the Control Word Queue (n2_crypto_probe). At that time, queue_cache[0] is NULL and a new kmem_cache will be allocated. If the subsequent n2_register_algs call fails, the kmem_cache will be released in queue_cache_destroy, but queue_cache_init[0] is not set back to NULL. So when the Module Arithmetic Unit gets probed next (n2_mau_probe), queue_cache_init will not allocate a kmem_cache again, but leave it as its bogus value, causing a BUG() to trigger when queue_cache[0] is eventually passed to kmem_cache_zalloc: n2_crypto: Found N2CP at /virtual-devices@100/n2cp@7 n2_crypto: Registered NCS HVAPI version 2.0 called queue_cache_init n2_crypto: md5 alg registration failed n2cp f028687c: /virtual-devices@100/n2cp@7: Unable to register algorithms. called queue_cache_destroy n2cp: probe of f028687c failed with error -22 n2_crypto: Found NCP at /virtual-devices@100/ncp@6 n2_crypto: Registered NCS HVAPI version 2.0 called queue_cache_init kernel BUG at mm/slab.c:2993! Call Trace: [0000000000604488] kmem_cache_alloc+0x1a8/0x1e0 (inlined) kmem_cache_zalloc (inlined) new_queue (inlined) spu_queue_setup (inlined) handle_exec_unit [0000000010c61eb4] spu_mdesc_scan+0x1f4/0x460 [n2_crypto] [0000000010c62b80] n2_mau_probe+0x100/0x220 [n2_crypto] [000000000084b174] platform_drv_probe+0x34/0xc0 Signed-off-by: Jan Engelhardt <jengelh@inai.de> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2026-05-10 15:59:33 +0300