summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2013-03-07ab8500-charger: Add AB8505_USB_LINK_STATUSHakan Berg1-8/+35
The AB8505 does not have the same address for USB link-status as has ab8500. Add AB8505_USB_LINK_STATUS and code to switch to correct constant. Signed-off-by: Hakan Berg <hakan.berg@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
2013-03-07ab8500-fg: Allow capacity to raise from 1% when chargingHakan Berg1-4/+2
When battery capacity was going below 1% fg is not supposed to report 0% unless we've got the LOW_BAT IRQ, no matter what the FG-algorithm says. This made fg get stuck at 1% if charger is connected when capacity is 1%. Signed-off-by: Hakan BERG <hakan.berg@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
2013-03-07ab8500-btemp: Filter btemp readingsHakan Berg1-6/+21
Battery tempreature readings sometimes fail and results in a value far from recent values. This patch adds a software filter that disposes such readings, by allowing direct updates on temperature only if two samples result in the same temperature. Else only allow 1 degree change from previous reported value in the direction of the new measurement. Signed-off-by: Hakan Berg <hakan.berg@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Martin SJOBLOM <martin.w.sjoblom@stericsson.com> Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
2013-03-07pm2301-charger: Wake system when ext charger is plugged-inRupesh Kumar1-1/+16
When in suspend state, upon plug-in of external AC charger the device needs to wake-up and charging operation started. Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
2013-03-07pm2301-charger: Die temp thermal protectionRupesh Kumar1-1/+21
This patch adds support for die temperature thermal protection in pm2301 driver. Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Hakan BERG <hakan.berg@stericsson.com> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
2013-03-07ab8500_charger: Prevent auto drop of VBUSLee Jones1-49/+120
Do not set higher current in stepping functionality if VBUS is dropping. After VBUS has dropped try to set current once again. If dropping again then we have found the maximum capability of the charger. Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-03-07pm2301-charger: Resolve I2C detection problem on ab9540Mustapha Ben Zoubeir1-9/+26
Signed-off-by: Mustapha Ben Zoubeir <mustapha.ben.zoubeir-nonst@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Tested-by: Olivier CLERGEAUD <olivier.clergeaud@stericsson.com>
2013-03-07pm2301-charger: Force main charger detectPer Forlin1-0/+2
Force main charger detect in turn on status. Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com> Signed-off-by: Per Forlin <per.forlin@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Tested-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
2013-03-07ab8500-bm: Charge only mode fixes for the ab9540Lee Jones3-0/+63
Fix for charging not getting enabled in charge only mode by external charger. Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-03-07pm2301-charger: Support for over voltage protection on the ab9540Rupesh Kumar2-14/+37
Added support for main charger over voltage protection. Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
2013-03-07ab8500-bm: Quick re-attach charging behaviourLee Jones2-2/+136
Due to a bug in some AB8500 ASICs charger removal cannot always be detected if the removal and reinsertion is done to close in time. This patch detects above described case and handles the situation so that charging will be kept turned on. Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-03-07ab8500-charger: Trivial coding style changesLee Jones1-6/+6
Enforce the white space character after 'if'. Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-03-07ab8500-charger: Add backup battery charge voltages on the ab8540Yang QU1-2/+17
Add 2.7v, 2.9v, 3.0v, 3.2v and 3.3v charging voltages for backup battery. Before that only 2.5v, 2.6v, 2.8v, 3.1v were available. Signed-off-by: Yang QU <yang.qu@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Tested-by: Xiao Mei ZHANG <xiaomei.zhang@stericsson.com>
2013-03-07ab8500-fg: Report unscaled capacityMartin Bergstrom1-3/+1
Unscaled capacity should be reported for POWER_SUPPLY_PROP_CAPACITY. Signed-off-by: Martin Bergstrom <martin.bergstrom@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
2013-03-07ab8500-fg: Add power cut feature for ab8505 and ab8540Lee Jones3-0/+515
Add support for a power cut feature which allows user to configure when ab8505 and ab8540 based platforms should shut down system due to low battery. Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-03-07abx500-chargalg: Store the AB8500 MFD parent device for platform differentiationLee Jones1-1/+4
Any platform can be dynamically probed for model and version number provided the AB8500 MFD parent device pointer is available. This patch obtains that pointer and stores it in a locally controlled struct for later use. Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-03-07pm2301-charger: Enable SW EOC control on the ab9540Rajkumar Kasirajan1-5/+43
End of charging is managed by SW. Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
2013-03-07pm2301_charger: Remove __exit, __init and __devexit_p()Lee Jones1-3/+3
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-03-07mfd: ab8500-debugfs: Trivially beautify the debugfs driverLee Jones1-97/+89
Just lots of white space corrections, changing some of the 4 space tabs to 8 and pulling back some of the double tabbing back into singles, such as the remaining of the driver. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-core: Hierarchical interrupt registersDariusz Szymczak1-76/+6
Make use of the hierarchical interrupt rergister called ITLatchHier1 - 3 also for the 8500 platform (currently the hierarchical interrupt registers are used only for the 8540 and 9540 platforms). This will make the interrupt routing go faster since fewer i2c reads need to made in the most common cases. Signed-off-by: Dariusz Szymczak <dariusz.xd.szymczak@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Convert to kstrtoul_from_usersrinidhi kasagar1-70/+30
Use kstrtoul_from_user for getting an unsigned long from userspace which is less error prone. Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Add explicit dependenciesLinus Walleij1-0/+3
As I am working on SPARSE_IRQ a number of implicit resource grabs in the kernel become evident. For example, some includes like <linux/irqs.h> would implicitly include <mach/irqs.h> and then from there <mach/db8500-regs.h>. In many cases it is masking the fact that drivers do not properly use resources to pass their dependencies, base addresses etc. So write explicit #include statements with TODO items to have this fixed the proper way to all drivers doing this. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-core: Add abx500-clk as an mfd child deviceUlf Hansson1-0/+12
Hierarchically, the abx500-clk shall be considered as a child of the ab8500 core. The abx500-clk is intiated at arch init and thus the clks will be available when clients needs them. Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Reviewed-by: Patrice CHOTARD <patrice.chotard@stericsson.com> Reviewed-by: Gabriel FERNANDEZ <gabriel.fernandez@stericsson.com> Reviewed-by: Philippe BEGNIC <philippe.begnic@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Add register map for ab8540.Lee Jones1-3/+419
Required to read out correct debug information from the AB chip. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debugfs: Change AB8500 debug permissionsLee Jones1-28/+28
Enable group write permissions for ab8500 debug MFD driver. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-core: Show turn on status at bootMattias Wallin1-0/+26
Several states can be detected when a device is initially turned on. This patch displays these states in the log. If none of the states are true, then we report that too. Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Add ADC input channel usb_id in debugfsLee Jones1-0/+35
Signed-off-by: Yang QU <yang.qu@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Alexandre BOURDIOL <alexandre.bourdiol@stericsson.com> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debugfs: Dump sim registersLee Jones1-0/+78
This patch allows to dump the SIM registers from debugfs. It will temporary change the config to allow APE side to read the SIM registers. Note that this read can cause problem on modem side since the modem can't read these registers while the operation is ongoing. Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-sysctrl: AB8505 doesn't have SYSCLKREQ5..8Rabin Vincent1-15/+22
So we're removing support for it. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Tested-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-core: Add additional resources to ab8505_iddet_resourcesLee Jones1-0/+24
Add VBUS_DET_R, VBUS_DET_F IRQ, ID_DET_PLUGR and ID_DET_PLUGF IRQ information to ab8505_iddet_resources. These are required to get interrupts for AB8505 cut-2. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-gpadc: Optimise GPADC driverLee Jones1-157/+55
Optimise GPADC driver: * for code readability and maintenance by grouping similar cheking * for performance by grouping several writing to control register Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Add support for the AB8540Lee Jones2-1/+329
Allow GPADC debug information to be shown when executing on an AB8540 based platform. Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@stericsson.com> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-gpadc: Add support for the AB8540Lee Jones1-40/+276
This patch enables the GPADC to work on AB8540 based platforms. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-sysctrl: Add new reset functionLee Jones1-0/+63
Add a new reset function which uses the AB WD with 0 timeout. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Add support for ab8505 and ab9540Lee Jones1-11/+372
Make it possible to dump all registers in ab8505 and ab9540. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debugfs: Add tests for ab8540 based platform initialisationsLee Jones2-3/+8
Signed-off-by: Alexandre Torgue <alexandre.torgue@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com> Tested-by: Maxime COQUELIN <maxime.coquelin@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-sysctrl: Error check clean upMarcus Danielsson1-16/+22
Add error checks to see if sysctrl was probed as it should. If the sysctrl_dev is not set the return value is -EINVAL. Signed-off-by: Marcus Danielsson <marcus.danielsson@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com> Tested-by: Per FORLIN <per.forlin@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Add wake-up infoJonas Aaberg1-5/+30
Add information regarding what ab interrupt that caused a wake-up from suspend in <debugfs>/ab8500/interrupts. Also print the name of the interrupts, not just the numbers. Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Per FORLIN <per.forlin@stericsson.com> Tested-by: Mattias WALLIN <mattias.wallin@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Better error handling on crashJonas Aaberg1-4/+11
Stop trying to read i2c registers if one fail. Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-core: Add Interrupt support for ab8540Lee Jones1-7/+43
ITSource/ITLatch 7, 8, 9 and 10 don't exist on AB8540. This patch replaces them with '-1' in the interrupt list, and handles the '-1' in the code accordingly. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-core: Rework MFD sub-device initialisation structuresLee Jones1-61/+182
Here we're separating Battery Management devices into their own structure, removing the common device structure & redistribute them amongst the individual platform structs and completing the population of them. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-core: Add ADC support for ab8540Lee Jones2-43/+98
Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Function to save all ABB registers to memLee Jones1-0/+50
Dump function that stores all readable ABB registers to a memory areas where they can be accessed from dump file. Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-debug: Print banks in hexMattias Wallin1-9/+9
This patch changes bank prints to use hex value. Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Daniel WILLERUD <daniel.willerud@stericsson.com> Tested-by: Jonas ABERG <jonas.aberg@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-core: APE Interrupts are not clearedLee Jones1-2/+3
There are missing register descriptions from the AB8505 user manual and these need to be masked so that the APEINT line can toggle. This patch also affects the behaviour of AB9540. Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com> Reviewed-by: Alexandre TORGUE <alexandre.torgue@stericsson.com> Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-gpadc: Add gpadc hw conversionLee Jones2-101/+473
Add the support of gpacd hw conversion and make the number of sample configurable. Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com> Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-gpadc: Reread on failureJonas Aaberg1-0/+5
Reread the gpadc once upon failure. Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-gpadc: Implemented suspend/resumeDaniel WILLERUD1-0/+28
suspend/resume methods implemented to prevent suspend while the gpadc driver is busy. Signed-off-by: Daniel WILLERUD <daniel.willerud@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-07mfd: ab8500-sysctrl: Update correct turn on statusRajkumar Kasirajan2-1/+40
In L9540, turn_on_status register is not updated correctly if the device is rebooted with AC/USB charger connected. Due to this, the device boots android instead of entering into charge only mode. Read the AC/USB status register to detect the charger presence and update the turn on status manually. Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com> Signed-off-by: Per Forlin <per.forlin@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Rupesh KUMAR <rupesh.kumar@stericsson.com> Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Tested-by: Rupesh KUMAR <rupesh.kumar@stericsson.com> Tested-by: Philippe LANGLAIS <philippe.langlais@stericsson.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2013-03-04Merge tag 'stable/for-linus-3.9-rc1-tag' of ↵Linus Torvalds3-48/+39
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen Pull Xen bug-fixes from Konrad Rzeszutek Wilk: - Update the Xen ACPI memory and CPU hotplug locking mechanism. - Fix PAT issues wherein various applications would not start - Fix handling of multiple MSI as AHCI now does it. - Fix ARM compile failures. * tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xenbus: fix compile failure on ARM with Xen enabled xen/pci: We don't do multiple MSI's. xen/pat: Disable PAT using pat_enabled value. xen/acpi: xen cpu hotplug minor updates xen/acpi: xen memory hotplug minor updates
generated by cgit v1.2.3 (git 2.39.0) at 2025-02-02 22:16:07 +0300