| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal into thermal-soc
|
|
Add resource managed version of thermal_zone_of_sensor_register() and
thermal_zone_of_sensor_unregister().
This helps in reducing the code size in error path, remove of
driver remove callbacks and making proper sequence for deallocations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The driver doesn't check if the regulator_get_optional return value is
-EPROBE_DEFER so it will wrongly assume that the regulator couldn't be
found just because the regulator driver wasn't registered yet, i.e:
exynos-tmu 10060000.tmu: Regulator node (vtmu) not found
In this case the return value should be propagated to allow the driver
probe function to be deferred until the regulator driver is registered.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The Exynos TMU DT binding says that the vtmu-supply is optional but the
driver uses devm_regulator_get() that creates a dummy regulator if it's
not defined in the DT. For example the following message is in the log:
10060000.tmu supply vtmu not found, using dummy regulator
Use the optional version of regulator_get() that doesn't create a dummy
regulator and instead returns a -ENODEV errno code. Since it's expected
that a regulator may not be defined and the driver will inform about it:
exynos-tmu 10060000.tmu: Regulator node (vtmu) not found
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
When DeviveTree contains more trip-points than SoC can configure
(usually more than four) and polling mode is not enabled, then the
remaining trip-points will be silently ignored. No interrupts will be
generated for them.
This might be quite dangerous when one provides DTB with a
non-configurable critical trip-point, like (assuming four supported
thresholds in TMU):
- alert @50 C (type: active),
- alert @60 C (type: active),
- alert @70 C (type: active),
- alert @80 C (type: active),
- critical @120 C (type: critical) <- no interrupts generated.
This is a mistake in DTB so print a message in such case.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Following the fix on thermal Kconfig, this
patch adds dependency on HAS_IOMEM so driver
properly compile test on UM arch.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The sign bit of temperature readback is bit 0, not bit 1.
Change to BIT(0) to fix it.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Matt Longnecker <mlongnecker@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed on many files with:
drivers/built-in.o: In function `kirkwood_thermal_probe':
kirkwood_thermal.c:(.text+0x390a25): undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `exynos_tmu_probe':
exynos_tmu.c:(.text+0x39246b): undefined reference to `devm_ioremap'
The users of devm_ioremap_resource() which are compile-testable should
depend on HAS_IOMEM.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
We don't need to initialize "ret". We can move the IS_ERR() checks into
the if condition instead of doing an assignment first. Also there is a
check for "ret" when we know it is zero so we can remove that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This driver only has runtime but no build time dependencies, so it can be
built for testing purposes if the Kconfig COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that drivers are
not affected by changes that could cause build regressions.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
As the TRM says, add the tsadc_q_sel to control the temperature-code
sequence since the rk3228/rk3399 need set this bit (1024 - tsadc_q)
as output.
Fixes: commit
b0d7033 "thermal: rockchip: Support the RK3399 SoCs in thermal driver"
7b02a5e "thermal: rockchip: Support the RK3228 SoCs in thermal driver"
Reported-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This patch renames to be more adapter compatibles since more and more
SoCs are supported in thermal driver.
Reported-by: Huang,Tao <huangtao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
the calculation use a global table, not their own table.
so adapt the table to the correct one.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
As the Dan report the smatch check the thermal driver warning:
drivers/thermal/rockchip_thermal.c:551 rockchip_configure_from_dt()
warn: impossible condition '(thermal->tshut_temp > ((~0 >> 1))) =>
(s32min-s32max > s32max)'
Although The shut_temp read from DT is u32,the temperature is currently
represented as int not long in the thermal driver.
Let's change to make shut_temp instead of the thermal->tshut_temp for
the condition.
Fixes: commit 437df2172e8d
("thermal: rockchip: consistently use int for temperatures")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Four small fixes for irqchip drivers:
- Add missing low level irq handler initialization on mxs, so
interrupts can acutally be delivered
- Add a missing barrier to the GIC driver
- Two fixes for the GIC-V3-ITS driver, addressing a double EOI write
and a cache flush beyond the actual region"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Add missing barrier to 32bit version of gic_read_iar()
irqchip/mxs: Add missing set_handle_irq()
irqchip/gicv3-its: Avoid cache flush beyond ITS_BASERn memory size
irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/android fix from Greg KH:
"Here is one patch, for the android binder driver, to resolve a
reported problem. Turns out it has been around for a while (since
3.15), so it is good to finally get it resolved.
It has been in linux-next for a while with no reported issues"
* tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a few USB fixes for 4.5-rc6
They fix a reported bug for some USB 3 devices by reverting the recent
patch, a MAINTAINERS change for some drivers, some new device ids, and
of course, the usual bunch of USB gadget driver fixes.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
MAINTAINERS: drop OMAP USB and MUSB maintainership
usb: musb: fix DMA for host mode
usb: phy: msm: Trigger USB state detection work in DRD mode
usb: gadget: net2280: fix endpoint max packet for super speed connections
usb: gadget: gadgetfs: unregister gadget only if it got successfully registered
usb: gadget: remove driver from pending list on probe error
Revert "usb: hub: do not clear BOS field during reset device"
usb: chipidea: fix return value check in ci_hdrc_pci_probe()
usb: chipidea: error on overflow for port_test_write
USB: option: add "4G LTE usb-modem U901"
USB: cp210x: add IDs for GE B650V3 and B850V3 boards
USB: option: add support for SIM7100E
usb: musb: Fix DMA desired mode for Mentor DMA engine
usb: gadget: fsl_qe_udc: fix IS_ERR_VALUE usage
usb: dwc2: USB_DWC2 should depend on HAS_DMA
usb: dwc2: host: fix the data toggle error in full speed descriptor dma
usb: dwc2: host: fix logical omissions in dwc2_process_non_isoc_desc
usb: dwc3: Fix assignment of EP transfer resources
usb: dwc2: Add extra delay when forcing dr_mode
|
|
Merge fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
dax: move writeback calls into the filesystems
dax: give DAX clearing code correct bdev
ext4: online defrag not supported with DAX
ext2, ext4: only set S_DAX for regular inodes
block: disable block device DAX by default
ocfs2: unlock inode if deleting inode from orphan fails
mm: ASLR: use get_random_long()
drivers: char: random: add get_random_long()
mm: numa: quickly fail allocations for NUMA balancing on full nodes
mm: thp: fix SMP race condition between THP page fault and MADV_DONTNEED
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Enumeration:
Revert x86 pcibios_alloc_irq() to fix regression (Bjorn Helgaas)
Marvell MVEBU host bridge driver:
Restrict build to 32-bit ARM (Thierry Reding)"
* tag 'pci-v4.5-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: mvebu: Restrict build to 32-bit ARM
Revert "PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()"
Revert "PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed"
Revert "x86/PCI: Don't alloc pcibios-irq when MSI is enabled"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One small fix to keep OMAP platforms working across a suspend/resume
cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: omap3+: dpll: use non-locking version of clk_get_rate
|
|
Commit d07e22597d1d ("mm: mmap: add new /proc tunable for mmap_base
ASLR") added the ability to choose from a range of values to use for
entropy count in generating the random offset to the mmap_base address.
The maximum value on this range was set to 32 bits for 64-bit x86
systems, but this value could be increased further, requiring more than
the 32 bits of randomness provided by get_random_int(), as is already
possible for arm64. Add a new function: get_random_long() which more
naturally fits with the mmap usage of get_random_int() but operates
exactly the same as get_random_int().
Also, fix the shifting constant in mmap_rnd() to be an unsigned long so
that values greater than 31 bits generate an appropriate mask without
overflow. This is especially important on x86, as its shift instruction
uses a 5-bit mask for the shift operand, which meant that any value for
mmap_rnd_bits over 31 acts as a no-op and effectively disables mmap_base
randomization.
Finally, replace calls to get_random_int() with get_random_long() where
appropriate.
This patch (of 2):
Add get_random_long().
Signed-off-by: Daniel Cashman <dcashman@android.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nick Kralevich <nnk@google.com>
Cc: Jeff Vander Stoep <jeffv@google.com>
Cc: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver uses PCI glue that is only available on 32-bit ARM. This used
to work fine as long as ARCH_MVEBU and ARCH_DOVE were exclusively 32-bit,
but there's a patch in the pipe to make ARCH_MVEBU also available on 64-bit
ARM.
[bhelgaas: changelog; patch is coming but not merged yet]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
991de2e59090 ("PCI, x86: Implement pcibios_alloc_irq() and
pcibios_free_irq()") appeared in v4.3 and helps support IOAPIC hotplug.
Олег reported that the Elcus-1553 TA1-PCI driver worked in v4.2 but not
v4.3 and bisected it to 991de2e59090. Sunjin reported that the RocketRAID
272x driver worked in v4.2 but not v4.3. In both cases booting with
"pci=routirq" is a workaround.
I think the problem is that after 991de2e59090, we no longer call
pcibios_enable_irq() for upstream bridges. Prior to 991de2e59090, when a
driver called pci_enable_device(), we recursively called
pcibios_enable_irq() for upstream bridges via pci_enable_bridge().
After 991de2e59090, we call pcibios_enable_irq() from pci_device_probe()
instead of the pci_enable_device() path, which does *not* call
pcibios_enable_irq() for upstream bridges.
Revert 991de2e59090 to fix these driver regressions.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=111211
Fixes: 991de2e59090 ("PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()")
Reported-and-tested-by: Олег Мороз <oleg.moroz@mcc.vniiem.ru>
Reported-by: Sunjin Yang <fan4326@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
CC: Jiang Liu <jiang.liu@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are two reverts of recent PCI-related ACPI core changes (one of
which caused some systems to crash on boot and the other was a cleanup
on top of it) and a devfreq fix for Tegra.
Specifics:
- Revert an ACPI core change related to IRQ management in PCI that
introduced code relying on the use of kmalloc() which turned out to
also run during early init when that's not available yet and caused
some systems to crash on boot for this reason along with a cleanup
on top of it (Rafael Wysocki).
- Prevent devfreq from flooding the kernel log with useless messages
on Tegra (which started to happen after some recent changes in the
devfreq core) by fixing the driver to follow the documentation and
the core's expectations in its ->target callback (Tomeu Vizoso)"
* tag 'pm+acpi-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI, PCI, irq: remove interrupt count restriction"
Revert "ACPI / PCI: Simplify acpi_penalize_isa_irq()"
PM / devfreq: tegra: Set freq in rate callback
|
|
* pm-devfreq:
PM / devfreq: tegra: Set freq in rate callback
* acpi-pci:
Revert "ACPI, PCI, irq: remove interrupt count restriction"
Revert "ACPI / PCI: Simplify acpi_penalize_isa_irq()"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SuperH driver fix from Simon Horman:
"Restore legacy clock domain on SuperH platforms"
* tag 'renesas-sh-drivers-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
drivers: sh: Restore legacy clock domain on SuperH platforms
|
|
Pull drm fixes from Dave Airlie:
"This is a bit larger than Id like, but I asked the Intel guys to pull
in some Skylake fixes in the possibly vain hope that Skylake might be
more functional now that I'm seeing production hardware shipping.
For i915, it's mostly the same patch in a few places, making sure the
hw doesn't turn off when we are programming it.
Apart from that are two nouveau fixes, one for a module defer bug, and
one for using nouveau on new Lenovo P50 models.
Then there are a bunch of AMDGPU fixes, one is a fix for v4.4 vblank
regressions, and some PM fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (26 commits)
drm/nouveau/disp/dp: ensure sink is powered up before attempting link training
drm/nouveau: platform: Fix deferred probe
drm/amdgpu: disable direct VM updates when vm_debug is set
amdgpu: fix NULL pointer dereference at tonga_check_states_equal
drm/i915/gen9: Verify and enforce dc6 state writes
drm/i915/gen9: Check for DC state mismatch
drm/radeon/pm: adjust display configuration after powerstate
drm/amdgpu/pm: adjust display configuration after powerstate
drm/amdgpu/pm: add some checks for PX
drm/amdgpu: fix locking in force performance level
drm/amdgpu/gfx8: fix priv reg interrupt enable
drm/i915/skl: Ensure HW is powered during DDB HW state readout
drm/i915/lvds: Ensure the HW is powered during HW state readout
drm/i915/hdmi: Ensure the HW is powered during HW state readout
drm/i915/dsi: Ensure the HW is powered during HW state readout
drm/i915/dp: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered when accessing the CRC HW block
drm/i915/ddi: Ensure the HW is powered during HW state readout
drm/i915/crt: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered during HW access in assert_pipe
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- Two fixes for compatibility with the ACPI 6.1 specification.
Without these fixes multi-interface DIMMs will fail to be probed, and
address range scrub commands to find memory errors will give results
that the kernel will mis-interpret. For multi-interface DIMMs Linux
will accept either the original 6.0 implementation or 6.1.
For address range scrub we'll only support 6.1 since ACPI formalized
this DSM differently than the original example [1] implemented in
v4.2. The expectation is that production systems will only ever ship
the ACPI 6.1 address range scrub command definition.
- The wider async address range scrub work targeting 4.6 discovered
that the original synchronous implementation in 4.5 is not sizing its
return buffer correctly.
- Arnd caught that my recent fix to the size of the pfn_t flags missed
updating the flags variable used in the pmem driver.
- Toshi found that we mishandle the memremap() return value in
devm_memremap().
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm: use 'u64' for pfn flags
devm_memremap: Fix error value when memremap failed
nfit: update address range scrub commands to the acpi 6.1 format
libnvdimm, tools/testing/nvdimm: fix 'ars_status' output buffer sizing
nfit: fix multi-interface dimm handling, acpi6.1 compatibility
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"Add a regression fix for changed sysfs path of bq27xxx_battery and
update MAINTAINERS file"
* tag 'for-v4.5-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: bq27xxx_battery: Restore device name
MAINTAINERS: update bq27xxx driver
|
|
This can happen under some annoying circumstances, and is a quick fix
until more substantial changes can be made.
Fixed eDP mode changes on (at least) the Lenovo P50.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
The error cleanup paths aren't quite correct and will crash upon
deferred probe.
Cc: stable@vger.kernel.org # v4.3+
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
CONFIG_ARCH_SHMOBILE is not only enabled for Renesas ARM platforms
(which are DT based and multi-platform), but also on a select set of
Renesas SuperH platforms (SH7722/SH7723/SH7724/SH7343/SH7366). Hence
since commit 0ba58de231066e47 ("drivers: sh: Get rid of
CONFIG_ARCH_SHMOBILE_MULTI"), the legacy clock domain is no longer
installed on these SuperH platforms, and module clocks may not be
enabled when needed, leading to driver failures.
To fix this, add an additional check for CONFIG_OF.
Fixes: 0ba58de231066e47 ("drivers: sh: Get rid of CONFIG_ARCH_SHMOBILE_MULTI").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
This is a bit large, but it really helps Skylake bugs we are seeing
on a number of laptops.
Most of the commits are quite similar, ensuring the display power
doesn't vanish under us during hardware access. Also do note that it's
not just Skylake that's affected.
* tag 'drm-intel-fixes-2016-02-22' of git://anongit.freedesktop.org/drm-intel:
drm/i915/gen9: Verify and enforce dc6 state writes
drm/i915/gen9: Check for DC state mismatch
drm/i915/skl: Ensure HW is powered during DDB HW state readout
drm/i915/lvds: Ensure the HW is powered during HW state readout
drm/i915/hdmi: Ensure the HW is powered during HW state readout
drm/i915/dsi: Ensure the HW is powered during HW state readout
drm/i915/dp: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered when accessing the CRC HW block
drm/i915/ddi: Ensure the HW is powered during HW state readout
drm/i915/crt: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered during HW access in assert_pipe
drm/i915: Ensure the HW is powered when disabling VGA
drm/i915/ibx: Ensure the HW is powered during PLL HW readout
drm/i915: Ensure the HW is powered during display pipe HW readout
drm/i915: Add helper to get a display power ref if it was already enabled
|
|
into drm-fixes
A few radeon and amdgpu fixes for 4.5. A few further fixes for the vblank
regressions in 4.4 and a couple of other minor fixes.
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: disable direct VM updates when vm_debug is set
amdgpu: fix NULL pointer dereference at tonga_check_states_equal
drm/radeon/pm: adjust display configuration after powerstate
drm/amdgpu/pm: adjust display configuration after powerstate
drm/amdgpu/pm: add some checks for PX
drm/amdgpu: fix locking in force performance level
drm/amdgpu/gfx8: fix priv reg interrupt enable
drm/amdgpu: Don't hang in amdgpu_flip_work_func on disabled crtc.
drm/radeon: Don't hang in radeon_flip_work_func on disabled crtc. (v2)
|
|
That should make user space bugs more obvious.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The event_data passed from pem_fini was not cleared upon initialization.
This caused NULL checks to pass and cast_const_phw_tonga_power_state to
attempt to dereference an invalid pointer. Clear the event_data in
pem_init and pem_fini before calling pem_handle_event.
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Bradley Pankow <btpankow@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.5-rc6
The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
|
|
Revert commit b5bd02695471 (ACPI, PCI, irq: remove interrupt count
restriction) that introduced a boot regression on some systems
where it caused kmalloc() to be used too early.
Link: http://marc.info/?l=linux-acpi&m=145580159209240&w=2
Reported-by: Nalla, Ravikanth <ravikanth.nalla@hpe.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Revert commit 0971686954f9 "ACPI / PCI: Simplify acpi_penalize_isa_irq()"
that depends on commit b5bd02695471 (ACPI, PCI, irq: remove interrupt
count restriction) which introduced a regression and needs to be
reverted for this reason.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix a 112 byte leak for each IO request that is requeued while DM
multipath is handling faults due to path failures.
This leak does not happen if blk-mq DM multipath is used. It only
occurs if .request_fn DM multipath is stacked ontop of blk-mq paths
(e.g. scsi-mq devices)"
* tag 'dm-4.5-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix dm_rq_target_io leak on faults with .request_fn DM w/ blk-mq paths
|
|
Pull MMC fix from Ulf Hansson:
"Here's an mmc fix intended for v4.5 rc6.
MMC host:
- omap_hsmmc: Fix PM regression for deferred probe"
* tag 'mmc-v4.5-rc4' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: omap_hsmmc: Fix PM regression with deferred probe for pm_runtime_reinit
|
|
A recent bugfix changed pfn_t to always be 64-bit wide, but did not
change the code in pmem.c, which is now broken on 32-bit architectures
as reported by gcc:
In file included from ../drivers/nvdimm/pmem.c:28:0:
drivers/nvdimm/pmem.c: In function 'pmem_alloc':
include/linux/pfn_t.h:15:17: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define PFN_DEV (1ULL << (BITS_PER_LONG_LONG - 3))
This changes the intermediate pfn_flags in struct pmem_device to
be 64 bit wide as well, so they can store the flags correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: db78c22230d0 ("mm: fix pfn_t vs highmem")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The original format of these commands from the "NVDIMM DSM Interface
Example" [1] are superseded by the ACPI 6.1 definition of the "NVDIMM Root
Device _DSMs" [2].
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
[2]: http://www.uefi.org/sites/default/files/resources/ACPI_6_1.pdf
"9.20.7 NVDIMM Root Device _DSMs"
Changes include:
1/ New 'restart' fields in ars_status, unfortunately these are
implemented in the middle of the existing definition so this change
is not backwards compatible. The expectation is that shipping
platforms will only ever support the ACPI 6.1 definition.
2/ New status values for ars_start ('busy') and ars_status ('overflow').
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit ac33cdb16681 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.
Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.
This patch fixes the issue by removing the explicit checks.
Issue is noticed on Qualcomm Dragon board DB410C.
[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
