| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 12e6ac69cc7e7d3367599ae26a92a0f9a18bc728 ]
Some NXP processors using ChipIdea USB IP have a bug when frame babble is
detected.
Issue description:
In USB camera test, our controller is host in HS mode. In ISOC IN, when
device sends data across the micro frame, it causes the babble in host
controller. This will clear the PE bit. In spec, it also requires to set
the PEC bit and then set the PCI bit. Without the PCI interrupt, the
software does not know the PE is cleared.
This will add a flag CI_HDRC_HAS_PORTSC_PEC_MISSED to some impacted
platform datas. And the ehci host driver will assert PEC by SW when
specific conditions are satisfied.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230809024432.535160-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dda4b60ed70bd670eefda081f70c0cb20bbeb1fa ]
Some NXP processor using chipidea IP has a bug when frame babble is
detected.
As per 4.15.1.1.1 Serial Bus Babble:
A babble condition also exists if IN transaction is in progress at
High-speed SOF2 point. This is called frame babble. The host controller
must disable the port to which the frame babble is detected.
The USB controller has disabled the port (PE cleared) and has asserted
USBERRINT when frame babble is detected, but PEC is not asserted.
Therefore, the SW isn't aware that port has been disabled. Then the
SW keeps sending packets to this port, but all of the transfers will
fail.
This workaround will firstly assert PCD by SW when USBERRINT is detected
and then judge whether port change has really occurred or not by polling
roothub status. Because the PEC doesn't get asserted in our case, this
patch will also assert it by SW when specific conditions are satisfied.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230809024432.535160-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ce9daa2efc0872a9a68ea51dc8000df05893ef2e ]
We should verify the bound of the array to assure that host
may not manipulate the index to point past endpoint array.
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20230628081511.186850-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2319b9c87fe243327285f2fefd7374ffd75a65fc ]
The device may be scheduled during the resume process,
so this cannot appear in atomic operations. Since
pm_runtime_set_active will resume suppliers, put set
active outside the spin lock, which is only used to
protect the struct cdns data structure, otherwise the
kernel will report the following warning:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1163
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 651, name: sh
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
CPU: 0 PID: 651 Comm: sh Tainted: G WC 6.1.20 #1
Hardware name: Freescale i.MX8QM MEK (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x30
dump_stack_lvl+0x64/0x80
dump_stack+0x1c/0x38
__might_resched+0x1fc/0x240
__might_sleep+0x68/0xc0
__pm_runtime_resume+0x9c/0xe0
rpm_get_suppliers+0x68/0x1b0
__pm_runtime_set_status+0x298/0x560
cdns_resume+0xb0/0x1c0
cdns3_controller_resume.isra.0+0x1e0/0x250
cdns3_plat_resume+0x28/0x40
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230616021952.1025854-1-xiaolei.wang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 59cf445754566984fd55af19ba7146c76e6627bc upstream.
Commit 85d07c556216 ("USB: core: Unite old scheme and new scheme
descriptor reads") altered the way USB devices are enumerated
following detection, and in the process it messed up the
initialization of SuperSpeed (or faster) devices:
[ 31.650759] usb 2-1: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcd
[ 31.663107] usb 2-1: device descriptor read/8, error -71
[ 31.952697] usb 2-1: new SuperSpeed Plus Gen 2x1 USB device number 3 using xhci_hcd
[ 31.965122] usb 2-1: device descriptor read/8, error -71
[ 32.080991] usb usb2-port1: attempt power cycle
...
The problem was caused by the commit forgetting that in SuperSpeed or
faster devices, the device descriptor uses a logarithmic encoding of
the bMaxPacketSize0 value. (For some reason I thought the 255 case in
the switch statement was meant for these devices, but it isn't -- it
was meant for Wireless USB and is no longer needed.)
We can fix the oversight by testing for buf->bMaxPacketSize0 = 9
(meaning 512, the actual maxpacket size for ep0 on all SuperSpeed
devices) and straightening out the logic that checks and adjusts our
initial guesses of the maxpacket value.
Reported-and-tested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Closes: https://lore.kernel.org/linux-usb/20230810002257.nadxmfmrobkaxgnz@synopsys.com/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads")
Link: https://lore.kernel.org/r/8809e6c5-59d5-4d2d-ac8f-6d106658ad73@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff33299ec8bb80cdcc073ad9c506bd79bb2ed20b upstream.
Syzbot reported an out-of-bounds read in sysfs.c:read_descriptors():
BUG: KASAN: slab-out-of-bounds in read_descriptors+0x263/0x280 drivers/usb/core/sysfs.c:883
Read of size 8 at addr ffff88801e78b8c8 by task udevd/5011
CPU: 0 PID: 5011 Comm: udevd Not tainted 6.4.0-rc6-syzkaller-00195-g40f71e7cd3c6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd9/0x150 lib/dump_stack.c:106
print_address_description.constprop.0+0x2c/0x3c0 mm/kasan/report.c:351
print_report mm/kasan/report.c:462 [inline]
kasan_report+0x11c/0x130 mm/kasan/report.c:572
read_descriptors+0x263/0x280 drivers/usb/core/sysfs.c:883
...
Allocated by task 758:
...
__do_kmalloc_node mm/slab_common.c:966 [inline]
__kmalloc+0x5e/0x190 mm/slab_common.c:979
kmalloc include/linux/slab.h:563 [inline]
kzalloc include/linux/slab.h:680 [inline]
usb_get_configuration+0x1f7/0x5170 drivers/usb/core/config.c:887
usb_enumerate_device drivers/usb/core/hub.c:2407 [inline]
usb_new_device+0x12b0/0x19d0 drivers/usb/core/hub.c:2545
As analyzed by Khazhy Kumykov, the cause of this bug is a race between
read_descriptors() and hub_port_init(): The first routine uses a field
in udev->descriptor, not expecting it to change, while the second
overwrites it.
Prior to commit 45bf39f8df7f ("USB: core: Don't hold device lock while
reading the "descriptors" sysfs file") this race couldn't occur,
because the routines were mutually exclusive thanks to the device
locking. Removing that locking from read_descriptors() exposed it to
the race.
The best way to fix the bug is to keep hub_port_init() from changing
udev->descriptor once udev has been initialized and registered.
Drivers expect the descriptors stored in the kernel to be immutable;
we should not undermine this expectation. In fact, this change should
have been made long ago.
So now hub_port_init() will take an additional argument, specifying a
buffer in which to store the device descriptor it reads. (If udev has
not yet been initialized, the buffer pointer will be NULL and then
hub_port_init() will store the device descriptor in udev as before.)
This eliminates the data race responsible for the out-of-bounds read.
The changes to hub_port_init() appear more extensive than they really
are, because of indentation changes resulting from an attempt to avoid
writing to other parts of the usb_device structure after it has been
initialized. Similar changes should be made to the code that reads
the BOS descriptor, but that can be handled in a separate patch later
on. This patch is sufficient to fix the bug found by syzbot.
Reported-and-tested-by: syzbot+18996170f8096c6174d0@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/000000000000c0ffe505fe86c9ca@google.com/#r
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Khazhy Kumykov <khazhy@google.com>
Fixes: 45bf39f8df7f ("USB: core: Don't hold device lock while reading the "descriptors" sysfs file")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/b958b47a-9a46-4c22-a9f9-e42e42c31251@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de28e469da75359a2bb8cd8778b78aa64b1be1f4 upstream.
The usb_get_device_descriptor() routine reads the device descriptor
from the udev device and stores it directly in udev->descriptor. This
interface is error prone, because the USB subsystem expects in-memory
copies of a device's descriptors to be immutable once the device has
been initialized.
The interface is changed so that the device descriptor is left in a
kmalloc-ed buffer, not copied into the usb_device structure. A
pointer to the buffer is returned to the caller, who is then
responsible for kfree-ing it. The corresponding changes needed in the
various callers are fairly small.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/d0111bb6-56c1-4f90-adf2-6cfe152f6561@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85d07c55621676d47d873d2749b88f783cd4d5a1 upstream.
In preparation for reworking the usb_get_device_descriptor() routine,
it is desirable to unite the two different code paths responsible for
initially determining endpoint 0's maximum packet size in a newly
discovered USB device. Making this determination presents a
chicken-and-egg sort of problem, in that the only way to learn the
maxpacket value is to get it from the device descriptor retrieved from
the device, but communicating with the device to retrieve a descriptor
requires us to know beforehand the ep0 maxpacket size.
In practice this problem is solved in two different ways, referred to
in hub.c as the "old scheme" and the "new scheme". The old scheme
(which is the approach recommended by the USB-2 spec) involves asking
the device to send just the first eight bytes of its device
descriptor. Such a transfer uses packets containing no more than
eight bytes each, and every USB device must have an ep0 maxpacket size
>= 8, so this should succeed. Since the bMaxPacketSize0 field of the
device descriptor lies within the first eight bytes, this is all we
need.
The new scheme is an imitation of the technique used in an early
Windows USB implementation, giving it the happy advantage of working
with a wide variety of devices (some of them at the time would not
work with the old scheme, although that's probably less true now). It
involves making an initial guess of the ep0 maxpacket size, asking the
device to send up to 64 bytes worth of its device descriptor (which is
only 18 bytes long), and then resetting the device to clear any error
condition that might have resulted from the guess being wrong. The
initial guess is determined by the connection speed; it should be
correct in all cases other than full speed, for which the allowed
values are 8, 16, 32, and 64 (in this case the initial guess is 64).
The reason for this patch is that the old- and new-scheme parts of
hub_port_init() use different code paths, one involving
usb_get_device_descriptor() and one not, for their initial reads of
the device descriptor. Since these reads have essentially the same
purpose and are made under essentially the same circumstances, this is
illogical. It makes more sense to have both of them use a common
subroutine.
This subroutine does basically what the new scheme's code did, because
that approach is more general than the one used by the old scheme. It
only needs to know how many bytes to transfer and whether or not it is
being called for the first iteration of a retry loop (in case of
certain time-out errors). There are two main differences from the
former code:
We initialize the bDescriptorType field of the transfer buffer
to 0 before performing the transfer, to avoid possibly
accessing an uninitialized value afterward.
We read the device descriptor into a temporary buffer rather
than storing it directly into udev->descriptor, which the old
scheme implementation used to do.
Since the whole point of this first read of the device descriptor is
to determine the bMaxPacketSize0 value, that is what the new routine
returns (or an error code). The value is stored in a local variable
rather than in udev->descriptor. As a side effect, this necessitates
moving a section of code that checks the bcdUSB field for SuperSpeed
devices until after the full device descriptor has been retrieved.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/495cb5d4-f956-4f4a-a875-1e67e9489510@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f23643306430f86e2f413ee2b986e0773e79da31 upstream.
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230814180559.923475-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c97cd0b4b54eb42aed7f6c3c295a2d137f6d2416 upstream.
When sending Discover Identity messages to a Port Partner that uses Power
Delivery v2 and SVDM v1, we currently send PD v2 messages with SVDM v2.0,
expecting the port partner to respond with its highest supported SVDM
version as stated in Section 6.4.4.2.3 in the Power Delivery v3
specification. However, sending SVDM v2 to some Power Delivery v2 port
partners results in a NAK whereas sending SVDM v1 does not.
NAK messages can be handled by the initiator (PD v3 section 6.4.4.2.5.1),
and one solution could be to resend Discover Identity on a lower SVDM
version if possible. But, Section 6.4.4.3 of PD v2 states that "A NAK
response Should be taken as an indication not to retry that particular
Command."
Instead, we can set the SVDM version to the maximum one supported by the
negotiated PD revision. When operating in PD v2, this obeys Section
6.4.4.2.3, which states the SVDM field "Shall be set to zero to indicate
Version 1.0." In PD v3, the SVDM field "Shall be set to 01b to indicate
Version 2.0."
Fixes: c34e85fa69b9 ("usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230731165926.1815338-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 55c3e571d2a0aabef4f1354604443f1c415d2e85 ]
Fix a "variable set but not used" warning in f_mass_storage.c. rc is
used if verbose debugging is enabled but not otherwise.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: d5e2b67aae79 ("USB: g_mass_storage: template f_mass_storage.c file created")
Link: https://lore.kernel.org/r/cfed16c7-aa46-494b-ba84-b0e0dc99be3a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 159a98afc88e88f588077afe818081d67f50a5e0 ]
Add a missing kerneldoc description of the vbus_work field in struct usb_udc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 50966da807c8 ("usb: gadget: udc: core: Offload usb_udc_vbus_handler processing")
Link: https://lore.kernel.org/r/1e5e7cda-b2c8-4917-9952-4354f365ede0@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5eda42aebb7668b4dcff025cd3ccb0d3d7c53da6 ]
The function mxs_phy_is_otg_host() will return true if OTG_ID_VALUE is
0 at USBPHY_CTRL register. However, OTG_ID_VALUE will not reflect the real
state if the ID pin is float, such as Host-only or Type-C cases. The value
of OTG_ID_VALUE is always 1 which means device mode.
This patch will fix the issue by judging the current mode based on
last_event. The controller will update last_event in time.
Fixes: 7b09e67639d6 ("usb: phy: mxs: refine mxs_phy_disconnect_line")
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627110353.1879477-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 23e60c8daf5ec2ab1b731310761b668745fcf6ed upstream.
According the "USB Type-C Port Controller Interface Specification v2.0"
the TCPC sets the fault status register bit-7
(AllRegistersResetToDefault) once the registers have been reset to
their default values.
This triggers an alert(-irq) on PTN5110 devices albeit we do mask the
fault-irq, which may cause a kernel hang. Fix this generically by writing
a one to the corresponding bit-7.
Cc: stable@vger.kernel.org
Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Reported-by: "Angus Ainslie (Purism)" <angus@akkea.ca>
Closes: https://lore.kernel.org/all/20190508002749.14816-2-angus@akkea.ca/
Reported-by: Christian Bach <christian.bach@scs.ch>
Closes: https://lore.kernel.org/regressions/ZR0P278MB07737E5F1D48632897D51AC3EB329@ZR0P278MB0773.CHEP278.PROD.OUTLOOK.COM/t/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230816172502.1155079-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78e0ea4277546debf7e96797ac3b768539cc44f6 upstream.
When partner does not support get_status message, tcpm right now
responds with soft reset message. This causes PD renegotiation to
happen and resets PPS link. Avoid soft resetting the link when
partner does not support get_status message to mitigate PPS resets.
[ 208.926752] Setting voltage/current limit 9500 mV 2450 mA
[ 208.930407] set_auto_vbus_discharge_threshold mode:3 pps_active:y vbus:9500 ret:0
[ 208.930418] state change SNK_TRANSITION_SINK -> SNK_READY [rev3 POWER_NEGOTIATION]
[ 208.930455] AMS POWER_NEGOTIATION finished
// ALERT message from the Source
[ 213.948442] PD RX, header: 0x19a6 [1]
[ 213.948451] state change SNK_READY -> GET_STATUS_SEND [rev3 GETTING_SOURCE_SINK_STATUS]
[ 213.948457] PD TX, header: 0x492
[ 213.950402] PD TX complete, status: 0
[ 213.950427] pending state change GET_STATUS_SEND -> GET_STATUS_SEND_TIMEOUT @ 60 ms [rev3 GETTING_SOURCE_SINK_STATUS]
// NOT_SUPPORTED from the Source
[ 213.959954] PD RX, header: 0xbb0 [1]
// sink sends SOFT_RESET
[ 213.959958] state change GET_STATUS_SEND -> SNK_SOFT_RESET [rev3 GETTING_SOURCE_SINK_STATUS]
[ 213.959962] AMS GETTING_SOURCE_SINK_STATUS finished
[ 213.959964] AMS SOFT_RESET_AMS start
[ 213.959966] state change SNK_SOFT_RESET -> AMS_START [rev3 SOFT_RESET_AMS]
[ 213.959969] state change AMS_START -> SOFT_RESET_SEND [rev3 SOFT_RESET_AMS]
Cc: stable@vger.kernel.org
Fixes: 8dea75e11380 ("usb: typec: tcpm: Protocol Error handling")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230820044449.1005889-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36668515d56bf73f06765c71e08c8f7465f1e5c4 upstream.
In current driver, the value of tuning parameter will not take effect
if samsung,picophy-* is assigned as 0. Because 0 is also a valid value
acccording to the description of USB_PHY_CFG1 register, this will improve
the logic to let it work.
Fixes: 58a3cefb3840 ("usb: chipidea: imx: add two samsung picophy parameters tuning implementation")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627112126.1882666-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1fa206bb764f37d2ab4bf671e483153ef0659b34 upstream.
Device connected to usb otg port of GXL-based boards can not be
recognised after resumption, doesn't recover even if disconnect and
reconnect the device. dmesg shows it disconnects during resumption.
[ 41.492911] usb 1-2: USB disconnect, device number 3
[ 41.499346] usb 1-2: unregistering device
[ 41.511939] usb 1-2: unregistering interface 1-2:1.0
Calling usb_post_init() will fix this issue, and it's tested and
verified on libretech's aml-s905x-cc board.
Cc: stable@vger.kernel.org # v5.8+
Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Signed-off-by: Luke Lu <luke.lu@libre.computer>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230809212911.18903-1-luke.lu@libre.computer
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d9488b294e1f8353bbcadc4c7172a7f7490199b upstream.
The difference of T99W368 and T99W373 is the chip solution.
T99W368 is designed based on Qualcomm SDX65 and T99W373 is SDX62.
Test evidence as below:
T: Bus=01 Lev=02 Prnt=05 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e0f0 Rev=05.04
S: Manufacturer=FII
S: Product=OLYMPIC USB WWAN Adapter
S: SerialNumber=78ada8c4
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
T: Bus=01 Lev=02 Prnt=05 Port=00 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e0ee Rev=05.04
S: Manufacturer=FII
S: Product=OLYMPIC USB WWAN Adapter
S: SerialNumber=78ada8d5
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
Both of them share the same port configuration:
0&1: MBIM, 2: Modem, 3:GNSS, 4:NMEA, 5:Diag
GNSS port don't use serial driver.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 873854c02364ebb991fc06f7148c14dfb5419e1b upstream.
Add Quectel EM05G with product ID 0x030e.
Interface 4 is used for qmi.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=030e Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Martin Kohn <m.kohn@welotec.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 53d061c19dc4cb68409df6dc11c40389c8c42a75 ]
USB PHY DPDM wakeup bit is enabled by default, when USB wakeup
is not required(/sys/.../wakeup is disabled), this bit should be
disabled, otherwise we will have unexpected wakeup if do USB device
connect/disconnect while system sleep.
This bit can be enabled for both host and device mode.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230517081907.3410465-3-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9a070e8e208995a9d638b538ed7abf28bd6ea6f0 ]
Use dedicated imx8ulp usb compatible to remove QoS request
since imx8ulp has no such limitation of imx7ulp: DMA will
not work if system enters idle.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230530104007.1294702-2-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c3ff12a92bd7072170978b8b41c2fa41b038139a ]
ISOC transfers expect a certain cadence of requests being queued. Not
keeping up with the expected rate of requests results in missed ISOC
transfers (EXDEV). The application layer may or may not produce video
frames to match this expectation, so uvc gadget driver must handle cases
where the application is not queuing up buffers fast enough to fulfill
ISOC requirements.
Currently, uvc gadget driver waits for new video buffer to become available
before queuing up usb requests. With this patch the gadget driver queues up
0 length usb requests whenever there are no video buffers available. The
USB controller's complete callback is used as the limiter for how quickly
the 0 length packets will be queued. Video buffers are still queued as
soon as they become available.
Link: https://lore.kernel.org/CAMHf4WKbi6KBPQztj9FA4kPvESc1fVKrC8G73-cs6tTeQby9=w@mail.gmail.com/
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20230508231103.1621375-1-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e5990469943c711cb00bfde6338d2add6c6d0bfe ]
When serial console over USB is enabled, gs_console_connect
queues gs_console_work, where it acquires the spinlock and
queues the usb request, and this request goes to gadget layer.
Now consider a situation where gadget layer prints something
to dmesg, this will eventually call gs_console_write() which
requires cons->lock. And this causes spinlock recursion. Avoid
this by excluding usb_ep_queue from the spinlock.
spin_lock_irqsave //needs cons->lock
gs_console_write
.
.
_printk
__warn_printk
dev_warn/pr_err
.
.
[USB Gadget Layer]
.
.
usb_ep_queue
gs_console_work
__gs_console_push // acquires cons->lock
process_one_work
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1683638872-6885-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5a5ccd61cfd76156cb3e0373c300c509d05448ce upstream.
When connecting to some DisplayPort partners, the initial status update
after entering DisplayPort Alt Mode notifies that the DFP_D/UFP_D is not in
the connected state. This leads to sending a configure message that keeps
the device in USB mode. The port partner then sets DFP_D/UFP_D to the
connected state and HPD to high in the same Attention message. Currently,
the HPD signal is dropped in order to handle configuration.
This patch saves changes to the HPD signal when the device chooses to
configure during dp_altmode_status_update, and invokes sysfs_notify if
necessary for HPD after configuring.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230726020903.1409072-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4270d2b4845e820b274702bfc2a7140f69e4d19d upstream.
Do not transition to SNK_UNATTACHED state when receiving vsafe0v event
while in SNK_HARD_RESET_WAIT_VBUS. Ignore VBUS off events as well as
in some platforms VBUS off can be signalled more than once.
[143515.364753] Requesting mux state 1, usb-role 2, orientation 2
[143515.365520] pending state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_SINK_ON @ 650 ms [rev3 HARD_RESET]
[143515.632281] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_HARD_RESET_SINK_OFF, polarity 1, disconnected]
[143515.637214] VBUS on
[143515.664985] VBUS off
[143515.664992] state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_WAIT_VBUS [rev3 HARD_RESET]
[143515.665564] VBUS VSAFE0V
[143515.665566] state change SNK_HARD_RESET_WAIT_VBUS -> SNK_UNATTACHED [rev3 HARD_RESET]
Fixes: 28b43d3d746b ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: <stable@vger.kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230712085722.1414743-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e21a620c7e6e00347ade1a6ed4967b359eada5a upstream.
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() because last_role is same
as current role. This happens since last_role gets initialised
to zero during the probe.
To avoid this, add a new flag initial_detection into struct
usb_conn_info, which prevents bailing out during initial
detection.
Cc: <stable@vger.kernel.org> # 5.4
Fixes: 4602f3bff266 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/1690880632-12588-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65dadb2beeb7360232b09ebc4585b54475dfee06 upstream.
Avichal Rakesh reported a kernel panic that occurred when the UVC
gadget driver was removed from a gadget's configuration. The panic
involves a somewhat complicated interaction between the kernel driver
and a userspace component (as described in the Link tag below), but
the analysis did make one thing clear: The Gadget core should
accomodate gadget drivers calling usb_gadget_deactivate() as part of
their unbind procedure.
Currently this doesn't work. gadget_unbind_driver() calls
driver->unbind() while holding the udc->connect_lock mutex, and
usb_gadget_deactivate() attempts to acquire that mutex, which will
result in a deadlock.
The simple fix is for gadget_unbind_driver() to release the mutex when
invoking the ->unbind() callback. There is no particular reason for
it to be holding the mutex at that time, and the mutex isn't held
while the ->bind() callback is invoked. So we'll drop the mutex
before performing the unbind callback and reacquire it afterward.
We'll also add a couple of comments to usb_gadget_activate() and
usb_gadget_deactivate(). Because they run in process context they
must not be called from a gadget driver's ->disconnect() callback,
which (according to the kerneldoc for struct usb_gadget_driver in
include/linux/usb/gadget.h) may run in interrupt context. This may
help prevent similar bugs from arising in the future.
Reported-and-tested-by: Avichal Rakesh <arakesh@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 286d9975a838 ("usb: gadget: udc: core: Prevent soft_connect_store() race")
Link: https://lore.kernel.org/linux-usb/4d7aa3f4-22d9-9f5a-3d70-1bd7148ff4ba@google.com/
Cc: Badhri Jagan Sridharan <badhri@google.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/48b2f1f1-0639-46bf-bbfc-98cb05a24914@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ddaa6a274578e23745b7466346fc2650df8f959 upstream.
If dwc3 is runtime suspended we defer processing the event buffer
until resume, by setting the pending_events flag. Set this flag before
triggering resume to avoid race with the runtime resume callback.
While handling the pending events, in addition to checking the event
buffer we also need to process it. Handle this by explicitly calling
dwc3_thread_interrupt(). Also balance the runtime pm get() operation
that triggered this processing.
Cc: stable@vger.kernel.org
Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM")
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230801192658.19275-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6ff6e7a9dd69364547751db0f626a10a6d628d2 upstream.
Syzbot got KMSAN to complain about access to an uninitialized value in
the alauda subdriver of usb-storage:
BUG: KMSAN: uninit-value in alauda_transport+0x462/0x57f0
drivers/usb/storage/alauda.c:1137
CPU: 0 PID: 12279 Comm: usb-storage Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
__msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
alauda_check_media+0x344/0x3310 drivers/usb/storage/alauda.c:460
The problem is that alauda_check_media() doesn't verify that its USB
transfer succeeded before trying to use the received data. What
should happen if the transfer fails isn't entirely clear, but a
reasonably conservative approach is to pretend that no media is
present.
A similar problem exists in a usb_stor_dbg() call in
alauda_get_media_status(). In this case, when an error occurs the
call is redundant, because usb_stor_ctrl_transfer() already will print
a debugging message.
Finally, unrelated to the uninitialized memory access, is the fact
that alauda_check_media() performs DMA to a buffer on the stack.
Fortunately usb-storage provides a general purpose DMA-able buffer for
uses like this. We'll use it instead.
Reported-and-tested-by: syzbot+e7d46eb426883fb97efd@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/0000000000007d25ff059457342d@google.com/T/
Suggested-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: e80b0fade09e ("[PATCH] USB Storage: add alauda support")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/693d5d5e-f09b-42d0-8ed9-1f96cd30bcce@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bef4b3cb95a5b883dfec8b3ffc0d671323d55bb upstream.
This reverts commit 5255660b208aebfdb71d574f3952cf48392f4306.
This quirk breaks at least the following hardware:
0b:00.0 0c03: 1106:3483 (rev 01) (prog-if 30 [XHCI])
Subsystem: 1106:3483
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 66
Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/4 Maskable- 64bit+
Address: 00000000fee007b8 Data: 0000
Capabilities: [c4] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 89W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <16us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis+ NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
with the quirk enabled it fails early with
[ 0.754373] pci 0000:0b:00.0: xHCI HW did not halt within 32000 usec status = 0x1000
[ 0.754419] pci 0000:0b:00.0: quirk_usb_early_handoff+0x0/0x7a0 took 31459 usecs
[ 2.228048] xhci_hcd 0000:0b:00.0: xHCI Host Controller
[ 2.228053] xhci_hcd 0000:0b:00.0: new USB bus registered, assigned bus number 7
[ 2.260073] xhci_hcd 0000:0b:00.0: Host halt failed, -110
[ 2.260079] xhci_hcd 0000:0b:00.0: can't setup: -110
[ 2.260551] xhci_hcd 0000:0b:00.0: USB bus 7 deregistered
[ 2.260624] xhci_hcd 0000:0b:00.0: init 0000:0b:00.0 fail, -110
[ 2.260639] xhci_hcd: probe of 0000:0b:00.0 failed with error -110
The hardware in question is an external PCIe card. It looks to me like the quirk
needs to be narrowed down. But this needs information about the hardware showing
the issue this quirk is to fix. So for now a clean revert.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 5255660b208a ("xhci: add quirk for host controllers that don't update endpoint DCS")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230713112830.21773-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 288b4fa1798e3637a9304c6e90a93d900e02369c upstream.
This reverts commit 18fc7c435be3f17ea26a21b2e2312fcb9088e01f.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this code, the patch means that certain tegra_xusb_probe() will
fail if the firmware supports power-domains but CONFIG_PM is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 18fc7c435be3 ("usb: xhci: tegra: Fix error check")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/8baace8d-fb4b-41a4-ad5f-848ae643a23b@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9fd10829a9eb482e192a845675ecc5480e0bfa10 upstream.
Allow devices to have dma operations beyond 64K, and avoid warnings such
as:
DMA-API: xhci-mtk 11200000.usb: mapping sg segment longer than device claims to support [len=98304] [max=65536]
Fixes: 0cbd4b34cda9 ("xhci: mediatek: support MTK xHCI host controller")
Cc: stable <stable@kernel.org>
Tested-by: Zubin Mithra <zsm@chromium.org>
Reported-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20230628-mtk-usb-v2-1-c8c34eb9f229@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2627335a1329a0d39d8d277994678571c4f21800 upstream.
Previously, the cdns3_gadget_check_config() function in the cdns3 driver
mistakenly calculated the ep_buf_size by considering only one
configuration's endpoint information because "claimed" will be clear after
call usb_gadget_check_config().
The fix involves checking the private flags EP_CLAIMED instead of relying
on the "claimed" flag.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230707230015.494999-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9dc162e22387080e2d06de708b89920c0e158c9a upstream.
The Focusrite Scarlett audio device does not behave correctly during
resumes. Below is what happens during every resume (captured with
Beagle 5000):
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset/Target disconnected>
<High Speed>
The Scarlett disconnects and is enumerated again.
However from time to time it drops completely off the USB bus during
resume. Below is captured occurrence of such an event:
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset>/<Chirp K>/<Tiny K>
<High Speed>
<Corrupted packet>
<Reset/Target disconnected>
To fix the condition a user has to unplug and plug the device again.
With USB_QUIRK_RESET_RESUME applied ("usbcore.quirks=1235:8211:b")
for the Scarlett audio device the issue still reproduces.
Applying USB_QUIRK_DISCONNECT_SUSPEND ("usbcore.quirks=1235:8211:m")
fixed the issue and the Scarlett audio device didn't drop off the USB
bus for ~5000 suspend/resume cycles where originally issue reproduced in
~100 or less suspend/resume cycles.
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230724112911.1802577-1-lb@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c55afcbeaa7a6f4fffdbc999a9bf3f0b29a5186f upstream.
The ohci_hcd_at91_drv_suspend() sets ohci->rh_state to OHCI_RH_HALTED when
suspend which will let the ohci_irq() skip the interrupt after resume. And
nobody to handle this interrupt.
According to the comment in ohci_hcd_at91_drv_suspend(), it need to reset
when resume from suspend(MEM) to fix by setting "hibernated" argument of
ohci_resume().
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230626152713.18950-1-aarongt.shen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f2327666a9080e428166964e37548b0168cd5e9 upstream.
A negative number from ret means the host controller had failed to send
usb message and 0 means succeed. Therefore, the if logic is wrong here
and this patch will fix it.
Fixes: f2b42379c576 ("usb: misc: ehset: Rework test mode entry")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230705095231.457860-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e835c0a4e23c38531dcee5ef77e8d1cf462658c7 upstream.
Commit c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on
system_suspend in host mode") replaces check for HOST only dr_mode with
current_dr_role. But during booting, the current_dr_role isn't
initialized, thus the device side reset is always issued even if dwc3
was configured as host-only. What's more, on some platforms with host
only dwc3, aways issuing device side reset by accessing device register
block can cause kernel panic.
Fixes: c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b32b8f2b9542d8039f5468303a6ca78c1b5611a5 upstream.
Hardware based on the Bay Trail / BYT SoCs require an external ULPI phy for
USB device-mode. The phy chip usually has its 'reset' and 'chip select'
lines connected to GPIOs described by ACPI fwnodes in the DSDT table.
Because of hardware with missing ACPI resources for the 'reset' and 'chip
select' GPIOs commit 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table
on platforms without ACPI GPIO resources") introduced a fallback
gpiod_lookup_table with hard-coded mappings for Bay Trail devices.
However there are existing Bay Trail based devices, like the National
Instruments cRIO-903x series, where the phy chip has its 'reset' and
'chip-select' lines always asserted in hardware via resistor pull-ups. On
this hardware the phy chip is always enabled and the ACPI dsdt table is
missing information not only for the 'chip-select' and 'reset' lines but
also for the BYT GPIO controller itself "INT33FC".
With the introduction of the gpiod_lookup_table initializing the USB
device-mode on these hardware now errors out. The error comes from the
gpiod_get_optional() calls in dwc3_pci_quirks() which will now return an
-ENOENT error due to the missing ACPI entry for the INT33FC gpio controller
used in the aforementioned table.
This hardware used to work before because gpiod_get_optional() will return
NULL instead of -ENOENT if no GPIO has been assigned to the requested
function. The dwc3_pci_quirks() code for setting the 'cs' and 'reset' GPIOs
was then skipped (due to the NULL return). This is the correct behavior in
cases where the phy chip is hardwired and there are no GPIOs to control.
Since the gpiod_lookup_table relies on the presence of INT33FC fwnode
in ACPI tables only add the table if we know the entry for the INT33FC
gpio controller is present. This allows Bay Trail based devices with
hardwired dwc3 ULPI phys to continue working.
Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@kernel.org>
Signed-off-by: Gratian Crisan <gratian.crisan@ni.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230726184555.218091-2-gratian.crisan@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 734ae15ab95a18d3d425fc9cb38b7a627d786f08 upstream.
This reverts commit b138e23d3dff90c0494925b4c1874227b81bddf7.
AutoRetry has been found to sometimes cause controller freezes when
communicating with buggy USB devices.
This controller feature allows the controller in host mode to send
non-terminating/burst retry ACKs instead of terminating retry ACKs
to devices when a transaction error (CRC error or overflow) occurs.
Unfortunately, if the USB device continues to respond with a CRC error,
the controller will not complete endpoint-related commands while it
keeps trying to auto-retry. [3] The xHCI driver will notice this once
it tries to abort the transfer using a Stop Endpoint command and
does not receive a completion in time. [1]
This situation is reported to dmesg:
[sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00
xhci-hcd: xHCI host not responding to stop endpoint command
xhci-hcd: xHCI host controller not responding, assume dead
xhci-hcd: HC died; cleaning up
Some users observed this problem on an Odroid HC2 with the JMS578
USB3-to-SATA bridge. The issue can be triggered by starting
a read-heavy workload on an attached SSD. After a while, the host
controller would die and the SSD would disappear from the system. [1]
Further analysis by Synopsys determined that controller revisions
other than the one in Odroid HC2 are also affected by this.
The recommended solution was to disable AutoRetry altogether.
This change does not have a noticeable performance impact. [2]
Revert the enablement commit. This will keep the AutoRetry bit in
the default state configured during SoC design [2].
Fixes: b138e23d3dff ("usb: dwc3: core: Enable AutoRetry feature in the controller")
Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1]
Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2]
Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3]
Cc: stable@vger.kernel.org
Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jakub Vanek <linuxtardis@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 609fded3f91972ada551c141c5d04a71704f8967 upstream.
The buffer address used in sysfs_emit should be aligned to PAGE_SIZE.
Use sysfs_emit_at instead to offset the buffer.
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b642dc9829507e4afabc03d32a18abbdb192c5e upstream.
The pointers of each usb_power_delivery handles are stored in "pds"
array returned from the pd_get ops but not in the adjacent memory
calculated from "pd". Get the handles from "pds" array directly instead
of deriving them from "pd".
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b33ebb2415e7e0a55ee3d049c2890d3a3e3805b6 upstream.
When calling device_add in the registration of typec_port, it will do
the NULL check on usb_power_delivery handle in typec_port for the
visibility of the device attributes. It is always NULL because port->pd
is set in typec_port_set_usb_power_delivery which is later than the
device_add call.
Set port->pd before device_add and only link the device after that.
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d245aedc00775c4d7265a9f4522cc4e1fd34d102 upstream.
Sort the driver symbols alphabetically in order to make it more obvious
where new driver entries should be added.
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd92c8a1f99bcd166204ffc219ea5a23dd65d64f upstream.
Add the device and product ID for this CAN bus interface / license
dongle. The device is usable either directly from user space or can be
attached to a kernel CAN interface with slcan_attach.
Reported-by: Kaufmann Automotive GmbH <info@kaufmann-automotive.ch>
Tested-by: Kaufmann Automotive GmbH <info@kaufmann-automotive.ch>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
[ johan: amend commit message and move entries in sort order ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 857ea9005806e2a458016880278f98715873e977 upstream.
Add Quectel EC200A "DIAG, AT, MODEM":
0x6005: ECM / RNDIS + DIAG + AT + MODEM
T: Bus=01 Lev=01 Prnt=02 Port=05 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=6005 Rev=03.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0000
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
Signed-off-by: Mohsen Tahmasebi <moh53n@moh53n.ir>
Tested-by: Mostafa Ghofrani <mostafaghrr@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f7cab49cecee16120d27c1734cfdf3d6c0e5329 upstream.
EM060K_128 is EM060K's sub-model, having the same name "Quectel EM060K-GL"
MBIM + GNSS + DIAG + NMEA + AT + QDSS + DPL
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0128 Rev= 5.04
S: Manufacturer=Quectel
S: Product=Quectel EM060K-GL
S: SerialNumber=f6fa08b6
C:* #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Jerry Meng <jerry-meng@foxmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6237390644fb92b81f5262877fe545d0d2c7b5d7 upstream.
Commit 286d9975a838 ("usb: gadget: udc: core: Prevent soft_connect_store() race")
introduced one extra mutex_unlock of connect_lock in the usb_gadget_active function.
Fixes: 286d9975a838 ("usb: gadget: udc: core: Prevent soft_connect_store() race")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230721222256.1743645-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83e30f2bf86ef7c38fbd476ed81a88522b620628 upstream.
Currently, increasing raw_dev->count happens before invoke the
raw_queue_event(), if the raw_queue_event() return error, invoke
raw_release() will not trigger the dev_free() to be called.
[ 268.905865][ T5067] raw-gadget.0 gadget.0: failed to queue event
[ 268.912053][ T5067] udc dummy_udc.0: failed to start USB Raw Gadget: -12
[ 268.918885][ T5067] raw-gadget.0: probe of gadget.0 failed with error -12
[ 268.925956][ T5067] UDC core: USB Raw Gadget: couldn't find an available UDC or it's busy
[ 268.934657][ T5067] misc raw-gadget: fail, usb_gadget_register_driver returned -16
BUG: memory leak
[<ffffffff8154bf94>] kmalloc_trace+0x24/0x90 mm/slab_common.c:1076
[<ffffffff8347eb55>] kmalloc include/linux/slab.h:582 [inline]
[<ffffffff8347eb55>] kzalloc include/linux/slab.h:703 [inline]
[<ffffffff8347eb55>] dev_new drivers/usb/gadget/legacy/raw_gadget.c:191 [inline]
[<ffffffff8347eb55>] raw_open+0x45/0x110 drivers/usb/gadget/legacy/raw_gadget.c:385
[<ffffffff827d1d09>] misc_open+0x1a9/0x1f0 drivers/char/misc.c:165
[<ffffffff8154bf94>] kmalloc_trace+0x24/0x90 mm/slab_common.c:1076
[<ffffffff8347cd2f>] kmalloc include/linux/slab.h:582 [inline]
[<ffffffff8347cd2f>] raw_ioctl_init+0xdf/0x410 drivers/usb/gadget/legacy/raw_gadget.c:460
[<ffffffff8347dfe9>] raw_ioctl+0x5f9/0x1120 drivers/usb/gadget/legacy/raw_gadget.c:1250
[<ffffffff81685173>] vfs_ioctl fs/ioctl.c:51 [inline]
[<ffffffff8154bf94>] kmalloc_trace+0x24/0x90 mm/slab_common.c:1076
[<ffffffff833ecc6a>] kmalloc include/linux/slab.h:582 [inline]
[<ffffffff833ecc6a>] kzalloc include/linux/slab.h:703 [inline]
[<ffffffff833ecc6a>] dummy_alloc_request+0x5a/0xe0 drivers/usb/gadget/udc/dummy_hcd.c:665
[<ffffffff833e9132>] usb_ep_alloc_request+0x22/0xd0 drivers/usb/gadget/udc/core.c:196
[<ffffffff8347f13d>] gadget_bind+0x6d/0x370 drivers/usb/gadget/legacy/raw_gadget.c:292
This commit therefore invoke kref_get() under the condition that
raw_queue_event() return success.
Reported-by: syzbot+feb045d335c1fdde5bf7@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Closes: https://syzkaller.appspot.com/bug?extid=feb045d335c1fdde5bf7
Signed-off-by: Zqiang <qiang.zhang1211@gmail.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/20230714074011.20989-1-qiang.zhang1211@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f4fc01af5b640bc39bd9403b5fd855345a2ad5f8 upstream.
The legacy gadget driver omitted calling usb_gadget_check_config()
to ensure that the USB device controller (UDC) has adequate resources,
including sufficient endpoint numbers and types, to support the given
configuration.
Previously, usb_add_config() was solely invoked by the legacy gadget
driver. Adds the necessary usb_gadget_check_config() after the bind()
operation to fix the issue.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230707230015.494999-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tegra_xudc_powerdomain_init()"
commit a8291be6b5dd465c22af229483dbac543a91e24e upstream.
This reverts commit f08aa7c80dac27ee00fa6827f447597d2fba5465.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this driver, the bug means that probe cannot succeed when CONFIG_PM
is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: f08aa7c80dac ("usb: gadget: tegra-xudc: Fix error check in tegra_xudc_powerdomain_init()")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/ZKQoBa84U/ykEh3C@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
