summaryrefslogtreecommitdiff
path: root/drivers/usb
AgeCommit message (Collapse)AuthorFilesLines
2015-01-27usb: phy: mxs: add delay before set phyctrl.clkgatePeter Chen1-3/+9
There is a request from IC engineer that if we doesn't set phypwd as 0xffffffff, we need to delay about five 32Khz cycles before set phy's pwd register, otherwise, the wakeup signal may can't wake up controller. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: phy: mxs: do not set PWD.RXPWD1PT1 for low speed connectionPeter Chen1-1/+46
At very rare cases, the SoF will not send out after resume with low speed connection. The workaround is do not power down PWD.RXPWD1PT1 bit during the suspend. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: phy: mxs: refine mxs_phy_disconnect_lineLi Jun1-1/+14
For non-otg mode, we keep the usage of disconnect line between phy analog and digital unchanging; for otg mode, at peripheral role, we keep the usage unchanging too, at host role, the digital part needs to know dp/dm change to respond device's data pulse when it is at low power mode. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Li Jun <b47624@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: phy: mxs: don't need IP fix for imx6sxPeter Chen1-2/+1
The RLT code has already done it, so no software operation is needed. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Fix USB disabled checkLaurent Pinchart3-9/+21
The isp1760 driver registration function returns an error if USB is disabled. This made sense when the driver only supported host controllers, but now that it supports peripheral controllers host support isn't mandatory anymore. Fix this by returning an error only when both the HCD and UDC functions are disabled, either through the kernel configuration or at runtime. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Remove duplicate usb_disabled() checkLaurent Pinchart1-3/+0
Both isp1760_register() and isp1761_pci_probe() check whether USB is disabled by calling usb_disabled(), and bail out with an error if it is. One check is enough, remove the PCI-specific check. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Make HCD support optionalLaurent Pinchart4-8/+71
Enable compilation of the isp1760 driver in pure host mode, pure device mode, or dual-role mode. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Move driver from drivers/usb/host/ to drivers/usb/isp1760/Laurent Pinchart15-26/+29
Now that this is DRD, it doesn't make sense to keep it under drivers/usb/host. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Add device controller supportLaurent Pinchart7-5/+1768
The ISP1761 is a dual-mode host and device controller backward compatible on the host side with the ISP1760. Add support for the device controller. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Move PORT1 configuration to core codeLaurent Pinchart2-9/+8
Configuring the mode of operation of port 1 doesn't belong to the HCD code, as it's related to the soon to come UDC support. Move the configuration to core code. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Initialize the bus interface in core codeLaurent Pinchart4-75/+105
Although the corresponding register is part of the HCD register space, processor bus initialization is not specific to the HCD. To prepare for device controller support, move bus interface initialization to core code. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Set IRQF_SHARED flag in core codeLaurent Pinchart2-7/+6
The IRQF_SHARED flag needs to be set regardless of the bus type. Don't require glue code to set it manually. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Move core code to isp1760-core.cLaurent Pinchart6-38/+114
Move core device initialization to a central location in order to share it with the device mode implementation. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Reorganize header filesLaurent Pinchart4-225/+256
The isp1760-rhcd.h header contains PTD constants and structures only useful for the HCD implementation. It also contains register definitions that will be needed by common code when implementing support for the ISP1761 device controller, but doesn't contain the isp1760_hcd structure definition that will also be used by common code. Move definitions to the right location and create an isp1760-regs.h to store register definitions. No change other than moving definitions and modifying indentation is performed. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Prefix driver data structures with isp1760_Laurent Pinchart2-9/+10
The slotinfo and memory_chunk structures are specific to the driver and defined in a header file. Prefix them with isp1760_ to avoid namespace clashes. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Decouple usb_hdc and isp1760_privLaurent Pinchart1-6/+15
Allocate the driver private data structure manually instead of using the usb_hcd private space. This will allow skipping hcd registration for the isp1761 when used in device mode only. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Refactor PCI initialization codeLaurent Pinchart1-65/+69
Move the initialization code out of the PCI probe function to a new function in order to simplify and fix error handling. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Use the managed devm_ioremap_resource() APILaurent Pinchart2-41/+16
This simplifies error and remove code paths. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Pass resource pointer to isp1760_registerLaurent Pinchart3-13/+11
The function takes quite a few arguments, passing the resource pointer instead of the start address and length simplifies it a bit. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Remove busname argument to isp1760_registerLaurent Pinchart3-6/+4
The argument is unused, remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Prefix init_kmem_once and deinit_kmem_cache with isp1760_Laurent Pinchart3-7/+7
The two functions are specific to the driver but have very generic names, subject to collisions. Rename them. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Fix indentation in probe error pathLaurent Pinchart1-3/+3
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Don't expose hcd to glue code from isp1760_registerLaurent Pinchart3-28/+19
The glue code probe functions don't need to access the hcd structure anymore. Modify isp1760_register to return an integer error code instead of the hcd pointer. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Manage device driver data in common codeLaurent Pinchart2-3/+2
Don't duplicate *_set_drvdata calls in glue code. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Move removal cleanup code to isp1760-hcd.cLaurent Pinchart3-14/+14
The removal cleanup code is duplicated between the different bus glues. Move it to a central location. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Merge platform and OF glue codesLaurent Pinchart1-135/+55
Both handle platform devices, merge them. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Unmap I/O registers at platform device removalLaurent Pinchart1-2/+1
The I/O registers are mapped in the HCD code but must be unmapped by glue code. The OF and PCI glue code unmap them correctly but the platform glue code is missing an iounmap() call. Fix it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Retrieve pdev memory resource from hcd at remove timeLaurent Pinchart1-5/+1
The platform driver remove function needs to release the memory resource requested at probe time. Instead of retrieving the resource from the platform device, retrieve it from the usb_hcd. This mimics the behaviour of the PCI and OF glues, and will make it easier to share code between all three glue layers. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Remove isp1760 glue structureLaurent Pinchart1-31/+15
The structure is allocated for the sole purpose of holding a pointer to the HCD and being stored in platform device driver data. Store the HCD pointer directly instead. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: isp1760: Use the gpio descriptor APILaurent Pinchart3-46/+19
Switching to the managed gpio descriptor API simplifies both error and cleanup code paths (by removing the need to free the gpio) and runtime code (by removing manual handling of the active low flag). It also permits handling the reset gpio entirely from within the HCD code, sharing it between the different glue layers. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: gadget: zero: fix format string warningsAsaf Vertz1-10/+10
Fixed the following warnings (reported by cppcheck): [drivers/usb/gadget/function/f_sourcesink.c:1217]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int'. [drivers/usb/gadget/function/f_sourcesink.c:1261]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int'. [drivers/usb/gadget/function/f_sourcesink.c:1305]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int'. [drivers/usb/gadget/function/f_sourcesink.c:1349]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int'. [drivers/usb/gadget/function/f_sourcesink.c:1393]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int'. [drivers/usb/gadget/function/f_sourcesink.c:1437]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int'. [drivers/usb/gadget/function/f_sourcesink.c:1476]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int'. [drivers/usb/gadget/function/f_sourcesink.c:1520]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int'. [drivers/usb/gadget/function/f_sourcesink.c:1564]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int'. [drivers/usb/gadget/function/f_sourcesink.c:1608]: (warning) %d in format string (no. 1) requires 'int' but the argument type is 'unsigned int' Reviewed-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: gadget: ffs: add eventfd notification about ffs eventsRobert Baldyga2-1/+29
Add eventfd which notifies userspace about ep0 events and AIO completion events. It simplifies using of FunctionFS with event loop, because now we need to poll on single file (instead of polling on ep0 and eventfd's supplied to AIO layer). FunctionFS eventfd is not triggered if another eventfd is supplied to AIO layer (in AIO request). It can be useful, for example, when we want to handle AIO transations for chosen endpoint in separate thread. Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: gadget: f_fs: Fix loop variableMario Schuknecht1-3/+3
Use if-loop variable 'epfile' instead of start variable 'epfiles'. Now the correct endpoint file name is stored. Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: gadget: Fix os desc testMario Schuknecht1-1/+1
USB vendor type is encoded in field bmRequestType. Make test USB_TYPE_VENDOR with bRequestType instead of bRequest. Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: musb: cppi41: improve rx channel abort routineBin Liu1-3/+9
1. set AUTOREQ to NONE at the beginning of teardown; 2. add delay for dma pipeline to drain; 3. Do not set USB_TDOWN bit for RX teardown. The CPPI hw has an issue that when tearing down a RX channel, if another RX channel is receiving data, the CPPI will lockup. To workaround the issue, do not set the CPPI TD bit. The steps before this point ensures the CPPI channel will be torn down properly. Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: musb: cppi41: correct the macro name EP_MODE_AUTOREG_*Bin Liu1-6/+6
The macro EP_MODE_AUTOREG_* should be called EP_MODE_AUTOREQ_*, as they are used for register AUTOREQ. Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: renesas_usbhs: add support for requesting DT DMAYoshihiro Shimoda1-1/+10
This patch adds dma_request_slave_channel_reason() calling to request dma slave channels for multiplatform environment. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: renesas_usbhs: add usbhsf_dma_init_pdev() functionYoshihiro Shimoda1-3/+9
To add support for requesting DT DMA in the future, this patch adds usbhsf_dma_init_pdev() function. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: renesas_usbhs: mod_host: use HUB_CHAR_*Sergei Shtylyov1-1/+2
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub Descriptor while the values are #define'd in <linux/usb/ch11.h>. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: musb: virthub: use HUB_CHAR_*Sergei Shtylyov1-3/+3
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub Descriptor while the values are #define'd in <linux/usb/ch11.h>. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19usb: dummy_hcd: use HUB_CHAR_*Sergei Shtylyov1-2/+6
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub Descriptor while the values are #define'd in <linux/usb/ch11.h>. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19usb: dwc2: hcd: use HUB_CHAR_*Sergei Shtylyov1-1/+3
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub Descriptor while the values are #define'd in <linux/usb/ch11.h>. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19usb: gadget: uvc: preserve the address passed to kfree()Andrzej Pietrasiewicz1-3/+7
__uvcg_fill_strm() called from __uvcg_iter_stream_cls() might have advanced the "data" even if __uvcg_iter_stream_cls() returns an error, so use a backup copy as an argument to kfree(). Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19Revert "usb: dwc2: add bus suspend/resume for dwc2"Paul Zimmerman1-77/+11
This reverts commit 0cf884e819e05437287a668b9bfcc198bab6329c. Even after applying the follow-on patch at https://patchwork.kernel.org/patch/5325111 there are still problems with device connect on the Altera SOCFPGA platform at least. One possible fix would be to add a whitelist to enable suspend/resume on platforms where it does work correctly. Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19usb: gadget: ethernet: re-use %pM specifier to print MACAndy Shevchenko1-3/+1
Instead of custom approach the patch converts code to use %pM specifier to print MAC. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19usb: phy: make GPIOs optional for the generic phyPaul Zimmerman1-2/+2
The use of GPIOs should be optional for the generic phy, otherwise the Altera SOCFPGA platform at least is broken. Fixes breakage caused by a combination of e9f2cefb0cd "usb: phy: generic: migrate to gpio_desc" and 135b3c4304d "usb: dwc2: platform: add generic PHY framework support". Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19usb: gadget: uvc: cleanup UVCG_FRAME_ATTR macroDan Carpenter1-26/+18
1) Change "conv" an "vnoc" to "to_cpu_endian" to "to_little_endian". 2) No need to check the "limit" because that is already handled in kstrtoXX so delete that parameter along with the check. 3) By using a "bits" parameter, we can combine the "uxx" parameter and the "str2u" parameters. 4) The kstrtou##bits() conversion does not need to be done under the mutex so move it to the start of the function. 5) Change the name of "identity_conv" to "noop_conversion". Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19usb: gadget: uvc: memory leak in uvcg_frame_make()Dan Carpenter1-0/+1
We need to add a kfree(h) on an error path. Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19usb: gadget: uvc: remove an impossible conditionDan Carpenter1-2/+0
"num" is a u32 so "(num > 0xFFFFFFFF)" is never true. Also the range is already checked in kstrtou32(). Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19usb: gadget: uvc: fix some error codesDan Carpenter1-7/+7
We're basically saying ERR_CAST(NULL) and PTR_ERR(NULL) here, which is nonsensical. Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-02-21 12:54:17 +0300