Age | Commit message (Collapse) | Author | Files | Lines |
|
commit 543aa4867d4a2dff5fc11e1b688197ee3bad7f89 upstream.
Triggering suspend to RAM via sysfs on a i.MX28 causes a NULL pointer
dereference. This patch avoids the oops in mxs_phy_get_vbus_status()
by aborting since there is no syscon available.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: efdbd3a5d6e ("usb: phy: mxs: do not set PWD.RXPWD1PT1 for low speed connection")
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83ed07c5db71bc02bd646d6eb60b48908235cdf9 upstream.
Static checkers complain that the current condition is never true. It
seems pretty likely that it's a typo and "URB" was intended instead of
"USB".
Fixes: 3d97ff63f899 ('usbdevfs: Use scatter-gather lists for large bulk transfers')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fb6d1f7df5d25299fd7b3e84b72b8851d3634764 upstream.
Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset.
Dissolve the function hub_port_finish_reset() completely and divide the
actions to be taken into those which need to be done after each reset
attempt and those which need to be done after the full procedure is
complete, and place them in the appropriate places in hub_port_reset().
Also, remove an unneeded forward declaration of hub_port_reset().
Verbose Problem Description:
USB 3.0 devices may be "lost for good" during a hub port reset.
This makes Linux unable to boot from USB 3.0 devices in certain
constellations of host controllers and devices, because the USB device is
lost during initialization, preventing the rootfs from being mounted.
The underlying problem is that in the affected constellations, during the
processing inside hub_port_reset(), the hub link state goes from 0 to
SS.inactive after the initial reset, and back to 0 again only after the
following "warm" reset.
However, hub_port_finish_reset() is called after each reset attempt and
sets the state the connected USB device based on the "preliminary" status
of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when
the following warm reset is complete and hub_port_finish_reset() is
called again, its call to set the device to USB_STATE_DEFAULT is blocked
by usb_set_device_state() which does not allow taking USB devices out of
USB_STATE_NOTATTACHED state.
Thanks to Alan Stern for guiding me to the proper solution and how to
submit it.
Link: http://lkml.kernel.org/r/trinity-25981484-72a9-4d46-bf17-9c1cf9301a31-1432073240136%20()%203capp-gmx-bs27
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aebda618718157a69c0dc0adb978d69bc2b8723c upstream.
This fixes an issue introduced in commit b23c843992b6 (usb: dwc3:
gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would
only use DEPSTARTCFG once per SetConfig.
The trick is that we should use one DEPSTARTCFG per SetConfig *OR*
SetInterface. SetInterface was completely missed from the original
patch.
This problem became aparent after commit 76e838c9f776 (usb: dwc3:
gadget: return error if command sent to DEPCMD register fails)
added checking of the return status of device endpoint commands.
'Set Endpoint Transfer Resource' command was caught failing
occasionally. This is because the Transfer Resource
Index was not getting reset during a SET_INTERFACE request.
Finally, to fix the issue, was we have to do is make sure that
our start_config_issued flag gets reset whenever we receive a
SetInterface request.
To verify the problem (and its fix), all we have to do is run
test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'.
Tested-by: Huang Rui <ray.huang@amd.com>
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Fixes: b23c843992b6 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs)
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e18b7975c885bc3a938b9a76daf32957ea0235fa upstream.
In case of non-Isochronous transfers, we don't
want to clear DWC3_EP_BUSY flag until XferComplete
event. That's because XferInProgress was only enabled
so we can recycle TRBs and usb_requests quicker, but
there are still other pending requests being transferred.
In order to make sure we don't allow for another StartTransfer
command while the HW is still processing other transfers,
we must keep DWC3_EP_BUSY flag set and this what this patch
does.
Fixes: f3af36511e60 (usb: dwc3: gadget: always enable IOC on
bulk/interrupt transfers)
Reported-by: sundeep subbaraya <sundeep.lkml@gmail.com>
Tested-by: sundeep subbaraya <sundeep.lkml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76e838c9f7765f9a6205b4d558d75a66104bc60d upstream.
We need to return error to caller if command is not sent to
controller succesfully.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: 72246da40f37 (usb: Introduce DesignWare USB3 DRD Driver)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 891b1dc022955d36cf4c0f42d383226a930db7ed upstream.
We need to return error to caller if command is not sent to
controller succesfully.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: b09bb64239c8 (usb: dwc3: gadget: implement Global Command support)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f14e9ad17f46051b02bffffac2036486097de19e upstream.
ffs_closed can race with configfs_rmdir which will call config_item_release, so
add an extra check to avoid calling the unregister_gadget_item with an null
gadget item.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15bf722e6f6c0b884521a0363204532e849deb7f upstream.
ATOL FPrint fiscal printers require usb_clear_halt to be executed
to work properly. Add quirk to fix the issue.
Signed-off-by: Alexey Sokolov <sokolov@7pikes.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.1-rc7
Here are a couple of new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Added the USB serial device ID for the HubZ dual ZigBee
and Z-Wave radio dongle.
Signed-off-by: John D. Blair <johnb@candicontrols.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.1-rc5
A few late important fixes which have been pending
on mailing list due to my vacations.
The important fixes are a fix for DEPCMD and DGCMD
status bitfields on DWC3, a couple fixes for Renesas
USB Controller, one of which prevents a broken DT
binding from reaching v4.1-final, and an old fix for
s3c2410-udc where pullup logic was reversed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch fixes an issue that sometimes this controller is not able
to complete the Control write status stage.
This driver should enable DCPCTR.CCPL and PID_BUF to complete the status
stage. However, if this driver detects the ctrl_stage interruption first
before the control write data is received, this driver will clear the
PID_BUF wrongly in the usbhsf_pio_try_pop(). To avoid this issue, this
patch doesn't clear the PID_BUF in the usbhsf_pio_try_pop().
(Since also the privious code doesn't disable the PID_BUF after a control
transfer was finished, this patch doesn't have any side efforts.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch fixes an issue for control write. When usbhsf_prepare_pop()
is called after this driver called a gadget setup function, this controller
doesn't receive the control write data. So, this patch adds a code to clear
the fifo for control write in usbhsf_prepare_pop().
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
when copying to iter the size can be different then the iov count,
the check for full iov is wrong and make any read on request which
is not the exactly size of iov to return -EFAULT.
So, just check the success of the copy.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Currently we always assign one of the two common implementations of
ep_offset and ep_select operations, overwriting any platform-specific
implementations.
Fixes: d026e9c76aac ("usb: musb: Change end point selection to use ...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Not checking config_ep_by_speed could lead to a kernel
NULL pointer dereference error in usb_ep_enable
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Originally FFS_FL_CALL_CLOSED_CALLBACK flag has been used to
indicate if we should call ffs_closed_callback().
Commit 4b187fceec3c ("usb: gadget: FunctionFS: add devices
management code") changed its semantic to indicate if we should
call ffs_closed() function which does a little bit more.
This situation leads to:
[ 122.362269] ------------[ cut here ]------------
[ 122.362287] WARNING: CPU: 2 PID: 2384 at drivers/usb/gadget/function/f_fs.c:3417 ffs_ep0_write+0x730/0x810 [usb_f_fs]()
[ 122.362292] Modules linked in:
[ 122.362555] CPU: 2 PID: 2384 Comm: adbd Tainted: G W 4.1.0-0.rc4.git0.1.1.fc22.i686 #1
[ 122.362561] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/25/2014
[ 122.362567] c0d1f947 415badfa 00000000 d1029e64 c0a86e54 00000000 d1029e94 c045b937
[ 122.362584] c0c37f94 00000002 00000950 f9b313d4 00000d59 f9b2ebf0 f9b2ebf0 fffffff0
[ 122.362600] 00000003 deb53d00 d1029ea4 c045ba42 00000009 00000000 d1029f08 f9b2ebf0
[ 122.362617] Call Trace:
[ 122.362633] [<c0a86e54>] dump_stack+0x41/0x52
[ 122.362645] [<c045b937>] warn_slowpath_common+0x87/0xc0
[ 122.362658] [<f9b2ebf0>] ? ffs_ep0_write+0x730/0x810 [usb_f_fs]
[ 122.362668] [<f9b2ebf0>] ? ffs_ep0_write+0x730/0x810 [usb_f_fs]
[ 122.362678] [<c045ba42>] warn_slowpath_null+0x22/0x30
[ 122.362689] [<f9b2ebf0>] ffs_ep0_write+0x730/0x810 [usb_f_fs]
[ 122.362702] [<f9b2e4c0>] ? ffs_ep0_read+0x380/0x380 [usb_f_fs]
[ 122.362712] [<c05a1c1f>] __vfs_write+0x2f/0x100
[ 122.362722] [<c05a42f2>] ? __sb_start_write+0x52/0x110
[ 122.362731] [<c05a2534>] vfs_write+0x94/0x1b0
[ 122.362740] [<c0a8a1c0>] ? mutex_lock+0x10/0x30
[ 122.362749] [<c05a2f41>] SyS_write+0x51/0xb0
[ 122.362759] [<c0a8c71f>] sysenter_do_call+0x12/0x12
[ 122.362766] ---[ end trace 0673d3467cecf8db ]---
in some cases (reproduction path below). This commit get back
semantic of that flag and ensures that ffs_closed() is called
always when needed but ffs_closed_callback() is called only
if this flag is set.
Reproduction path:
Compile kernel without any UDC driver or bound some gadget
to existing one and then:
$ modprobe g_ffs
$ mount none -t functionfs mount_point
$ ffs-example mount_point
This will fail with -ENODEV as there is no udc.
$ ffs-example mount_point
This will fail with -EBUSY because ffs_data has not been
properly cleaned up.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Returning non-zero value from ready callback makes ffs instance
return error from writing strings and enter FFS_CLOSING state.
This means that this this function is not truly ready and
close callback will not be called. This commit fix
ffs_ready_callback() to undo all side effects of this function
in case of error.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
For some reason the code has always been disabling pullup
when asked to do the opposite. According to surrounding code
and gadget API this seems to be a mistake. This fix allows
UDC to be detected by host controller on recent kernels.
Signed-off-by: Sergiy Kibrik <sakib@meta.ua>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Fixed the incorrect macro definitions correctly as per databook.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: b09bb64239c8 (usb: dwc3: gadget: implement Global Command support)
Cc: <stable@vger.kernel.org> #v3.5+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Since commit 1c6c69525b40 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Since commit 1c6c69525b40 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".
Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Regression in commit 638139eb95d2 ("usb: hub: allow to process more usb
hub events in parallel")
The regression resulted in intermittent failure to initialise a 10-port
hub (with three internal VL812 4-port hub controllers) on boot, with a
failure rate of around 8%, due to multiple race conditions when
accessing addr_dev and slot_id in struct xhci_hcd.
This regression also exposed a problem with xhci_setup_device, which
"should be protected by the usb_address0_mutex" but no longer is due to
commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus")
With separate buses (and locks) it is no longer the case that a single
lock will protect xhci_setup_device from accesses by two parallel
threads processing events on the two buses.
Fix this by adding a mutex to protect addr_dev and slot_id in struct
xhci_hcd, and by making the assignment of slot_id atomic.
Fixes multiple boot errors:
[ 0.583008] xhci_hcd 0000:00:14.0: Bad Slot ID 2
[ 0.583009] xhci_hcd 0000:00:14.0: Could not allocate xHCI USB device data structures
[ 0.583012] usb usb1-port3: couldn't allocate usb_device
And:
[ 0.637409] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.637417] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.637421] usb usb1-port1: couldn't allocate usb_device
And:
[ 0.753372] xhci_hcd 0000:00:14.0: ERROR: unexpected setup context command completion code 0x0.
[ 0.753373] usb 1-3: hub failed to enable device, error -22
[ 0.753400] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.753402] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.753403] usb usb1-port3: couldn't allocate usb_device
And:
[ 11.018386] usb 1-3: device descriptor read/all, error -110
And:
[ 5.753838] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
Tested with 200 reboots, resulting in no USB hub init related errors.
Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.kernel.org/g/CAP-bSRb=A0iEYobdGCLpwynS7pkxpt_9ZnwyZTPVAoy0Y=Zo3Q@mail.gmail.com
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
[changed git commit description style for checkpatch -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixed regression. After commit 29e409f0f761 ("xhci: Allow xHCI drivers to
be built as separate modules") the module xhci_hcd became non-removable.
That behaviour is not expected and there're no notes about it in commit
message. The module should be removable as it blocks PM suspend/resume
functions (Debian Bug#666406).
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds support for new Xsens device, Motion Tracker Development Board,
using Xsens' own Vendor ID
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.1-rc4
Here are a few device-id changes removing a duplicate entry, refining
another and adding a third.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
When midi function is created, 'id' attribute is initialized with
SNDRV_DEFAULT_STR1, which is NULL pointer. Trying to read this attribute
before filling it ends up with segmentation fault.
This commit fix this issue by preventing null pointer dereference. Now
f_midi_opts_id_show() returns empty string when id is a null pointer.
Reproduction path:
$ mkdir functions/midi.0
$ cat functions/midi.0/id
[ 53.130132] Unable to handle kernel NULL pointer dereference at
virtual address 00000000
[ 53.132630] pgd = ec6cc000
[ 53.135308] [00000000] *pgd=6b759831, *pte=00000000, *ppte=00000000
[ 53.141530] Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[ 53.146904] Modules linked in: usb_f_midi snd_rawmidi libcomposite
[ 53.153071] CPU: 1 PID: 2936 Comm: cat Not tainted
3.19.0-00041-gcf4b216 #7
[ 53.160010] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 53.166088] task: ee234c80 ti: ec764000 task.ti: ec764000
[ 53.171482] PC is at strlcpy+0x8/0x60
[ 53.175128] LR is at f_midi_opts_id_show+0x28/0x3c [usb_f_midi]
[ 53.181019] pc : [<c0222a9c>] lr : [<bf01bed0>] psr: 60000053
[ 53.181019] sp : ec765ef8 ip : 00000141 fp : 00000000
[ 53.192474] r10: 00019000 r9 : ed7546c0 r8 : 00010000
[ 53.197682] r7 : ec765f80 r6 : eb46a000 r5 : eb46a000 r4 :
ed754734
[ 53.204192] r3 : ee234c80 r2 : 00001000 r1 : 00000000 r0 :
eb46a000
[ 53.210704] Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM
Segment user
[ 53.217907] Control: 10c5387d Table: 6c6cc04a DAC: 00000015
[ 53.223636] Process cat (pid: 2936, stack limit = 0xec764238)
[ 53.229364] Stack: (0xec765ef8 to 0xec766000)
[ 53.233706] 5ee0:
ed754734 ed7546c0
[ 53.241866] 5f00: eb46a000 bf01bed0 eb753b80 bf01cc44 eb753b98
bf01b0a4 bf01b08c c0125dd0
[ 53.250025] 5f20: 00002f19 00000000 ec432e00 bf01cce8 c0530c00
00019000 00010000 ec765f80
[ 53.258184] 5f40: 00010000 ec764000 00019000 c00cc4ac ec432e00
c00cc55c 00000017 000081a4
[ 53.266343] 5f60: 00000001 00000000 00000000 ec432e00 ec432e00
00010000 00019000 c00cc620
[ 53.274502] 5f80: 00000000 00000000 00000000 00010000 ffff1000
00019000 00000003 c000e9a8
[ 53.282662] 5fa0: 00000000 c000e7e0 00010000 ffff1000 00000003
00019000 00010000 00019000
[ 53.290821] 5fc0: 00010000 ffff1000 00019000 00000003 7fffe000
00000001 00000000 00000000
[ 53.298980] 5fe0: 00000000 be8c68d4 0000b995 b6f0e3e6 40000070
00000003 00000000 00000000
[ 53.307157] [<c0222a9c>] (strlcpy) from [<bf01bed0>]
(f_midi_opts_id_show+0x28/0x3c [usb_f_midi])
[ 53.316006] [<bf01bed0>] (f_midi_opts_id_show [usb_f_midi]) from
[<bf01b0a4>] (f_midi_opts_attr_show+0x18/0x24 )
[ 53.327209] [<bf01b0a4>] (f_midi_opts_attr_show [usb_f_midi]) from
[<c0125dd0>] (configfs_read_file+0x9c/0xec)
[ 53.337180] [<c0125dd0>] (configfs_read_file) from [<c00cc4ac>]
(__vfs_read+0x18/0x4c)
[ 53.345073] [<c00cc4ac>] (__vfs_read) from [<c00cc55c>]
(vfs_read+0x7c/0x100)
[ 53.352190] [<c00cc55c>] (vfs_read) from [<c00cc620>]
(SyS_read+0x40/0x8c)
[ 53.359056] [<c00cc620>] (SyS_read) from [<c000e7e0>]
(ret_fast_syscall+0x0/0x34)
[ 53.366513] Code: ebffe3d3 e8bd8008 e92d4070 e1a05000 (e5d14000)
[ 53.372641] ---[ end trace e4f53a4e233d98d0 ]---
Signed-off-by: Pawel Szewczyk <p.szewczyk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Without this flag some versions of these enclosures do not work.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Christian Schaller <cschalle@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I've had the same issue as described in commit
c68929f75dfcb6354918862b91b5778585de1fa5
Except my touchscreen's ID is
ID 04f3:0125 Elan Microelectronics Corp.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the xHCI host controller has died (ie, device removed) or suffered
other serious fatal error (STS_FATAL), then xhci_irq should handle this
condition with IRQ_HANDLED instead of -ESHUTDOWN.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Our event ring consists of only one segment, and we risk filling
the event ring in case we get isoc transfers with short intervals
such as webcams that fill a TD every microframe (125us)
With 64 TRB segment size one usb camera could fill the event ring in 8ms.
A setup with several cameras and other devices can fill up the
event ring as it is shared between all devices.
This has occurred when uvcvideo queues 5 * 32TD URBs which then
get cancelled when the video mode changes. The cancelled URBs are returned
in the xhci interrupt context and blocks the interrupt handler from
handling the new events.
A full event ring will block xhci from scheduling traffic and affect all
devices conneted to the xhci, will see errors such as Missed Service
Intervals for isoc devices, and and Split transaction errors for LS/FS
interrupt devices.
Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring
size, which is welcome as for most isoc transfer we had to dynamically
expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo
queues.
The default size used to be 64 TRBs per segment
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Isoc TDs usually consist of one TRB, sometimes two. When all goes well we
receive only one success event for a TD, and move the dequeue pointer to
the next TD.
This fails if the TD consists of two TRBs and we get a transfer error
on the first TRB, we will then see two events for that TD.
Fix this by making sure the event we get is for the last TRB in that TD
before moving the dequeue pointer to the next TD. This will resolve some
of the uvc and dvb issues with the
"ERROR Transfer event TRB DMA ptr not part of current TD" error message
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Only a small fix for /sys entry
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.1-rc2
Here's the first pull request for v4.1-rc cycle,
it contains a few interesting fixes including a
fix to correct register offsets on dwc3, a fix
for Kconfig dependencies on isp1301 phy driver,
and a bug fix for our configfs gadget creation
interface.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
A string written by the user may not be zero terminated.
sscanf may read memory beyond the buffer if no zero byte
is found.
For testing build with CONFIG_USB_CHIPIDEA=y, CONFIG_USB_CHIPIDEA_DEBUG=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
Samsung has just released a portable USB3 SSD, coming in a very small
and nice form factor. It's USB ID is 04e8:8001, which unfortunately is
already used by the Palm Visor driver for the Samsung I330 phone cradle.
Having pl2303 or visor pick up this device ID results in conflicts with
the usb-storage driver, which handles the newly released portable USB3
SSD.
To work around this conflict, I've dug up a mailing list post [1] from a
long time ago, in which a user posts the full USB descriptor
information. The most specific value in this appears to be the interface
class, which has value 255 (0xff). Since usb-storage requires an
interface class of 0x8, I believe it's correct to disambiguate the two
devices by matching on 0xff inside visor.
[1] http://permalink.gmane.org/gmane.linux.usb.user/4264
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This phone is already supported by the visor driver.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Added the USB serial console device ID for KCF Technologies PRN device
which has a USB port for its serial console.
Signed-off-by: Mark Edwards <sonofaforester@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Phil and I found out a problem with commit:
7e860a6e7aa6 ("cdc-acm: add sanity checks")
It added some sanity checks to ignore potential garbage in CDC headers but
also introduced a potential infinite loop. This can happen at the first
loop iteration (elength = 0 in that case) if the description isn't a
DT_CS_INTERFACE or later if 'buffer[0]' is zero.
It should also be noted that the wrong length was being added to 'buffer'
in case 'buffer[1]' was not a DT_CS_INTERFACE descriptor, since elength was
assigned after that check in the loop.
A specially crafted USB device could be used to trigger this infinite loop.
Fixes: 7e860a6e7aa6 ("cdc-acm: add sanity checks")
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
CC: Oliver Neukum <oneukum@suse.de>
CC: Adam Lee <adam8157@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 70843f623b58 ("usb: host: ehci-msm: Use
devm_ioremap_resource instead of devm_ioremap") and commit
e507bf577e5a ("host: ehci-msm: remove duplicate check on resource"),
because msm_otg and this driver are using same address space to
access AHB mode and USB command registers.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Wrongly release mutex lock during otg_statemachine may result in re-enter
otg_statemachine, which is not allowed, we should do next state transtition
after previous one completed.
Fixes: 826cfe751f3e ("usb: chipidea: add OTG fsm operation functions implementation")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Testing has shown that ASM1053 devices do not work properly with transfers
larger than 240 sectors, so set max_sectors to 240 on these.
Cc: stable@vger.kernel.org # 3.16
Reported-by: Steve Bangert <sbangert@frontier.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Steve Bangert <sbangert@frontier.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usb-storage driver sets max_sectors = 240 in its scsi-host template,
for uas we do not want to do that for all devices, but testing has shown
that some devices need it.
This commit adds a US_FL_MAX_SECTORS_240 flag for such devices, and
implements support for it in uas.c, while at it it also adds support
for US_FL_MAX_SECTORS_64 to uas.c.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uas_use_uas_driver may set some US_FL_foo flags during detection, currently
these are stored in a local variable and then throw away, but these may be
of interest to the caller, so add an extra parameter to (optionally) return
the detected flags, and use this in the uas driver.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent change introduced a link error for the composite
printer gadget driver:
`printer_unbind' referenced in section `.ref.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Evidently the unbind function should not be marked __exit here,
because it is called through a callback pointer that is not necessarily
discarded, __composite_unbind() is indeed called from the error path of
composite_bind(), which can never work for a built-in driver.
Looking at the surrounding code, I found the same problem in all other
composite gadget drivers in both the bind and unbind functions, as
well as the udc platform driver 'remove' functions. Those will break
if anyone uses the 'unbind' sysfs attribute to detach a device from a
built-in driver.
This patch removes the incorrect annotations from all the gadget
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The isp1301-omap driver contains special hooks for the TPS65010
power management controller. It provides its own 'tps65010_set_vbus_draw'
wrapper in case that driver is not enabled through Kconfig, but
fails to handle the case where isp1301-omap is built-in but TPS65010
is a loadable module, which currently results in a link error:
drivers/built-in.o: In function `isp1301_set_power':
:(.text+0x14e188): undefined reference to `tps65010_set_vbus_draw'
This is a workaround to use the same trick as before also when
tps65010 is a module. Doing a proper fix would require much larger
changes to the driver that is not really worth it when the usb-phy
drivers are going to eventually get replaced with generic-phy
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When a single thread is sending out data over the gadget serial port,
gs_start_tx() will be called both from the sender context and from the
write completion. Since the port lock is released before the packet is
queued, the order in which the URBs are submitted is not guaranteed.
E.g.
sending thread completion (interrupt)
gs_write()
LOCK
gs_write_complete()
LOCK (wait)
gs_start_tx()
req1 = list_entry(pool->next)
UNLOCK
LOCK (acquired)
gs_start_tx()
req2 = list_entry(pool->next)
UNLOCK
usb_ep_queue(req2)
usb_ep_queue(req1)
I.e., req2 is submitted before req1 but it contains the data that
comes after req1.
To reproduce, use SMP with sending thread and completion pinned to
different CPUs, or use PREEMPT_RT, and add the following delay just
before the call to usb_ep_queue():
if (port->write_started > 0 && !list_empty(pool))
udelay(1000);
To work around this problem, make sure that only one thread is running
through the gs_start_tx() loop with an extra flag write_busy. Since
gs_start_tx() is always called with the port lock held, no further
synchronisation is needed. The original caller will continue through
the loop when the request was successfully submitted.
Signed-off-by: Philip Oberstaller <Philip.Oberstaller@septentrio.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If we have multiple instances of hid function, each of
them may have different report descriptor, also their
length may be different.
Currently we are using static hidg_desc varable which
is being filled in hidg_bind(). Then we send its content
to host in hidg_setup() function. This content may
have been already overwriten if another instance
has executed hidg_bind().
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|