| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 18e03310b5caa6d11c1a8c61b982c37047693fba upstream.
The current entry in unusual_cypress.h for the Super TOP SATA bridge devices
seems to be causing corruption on newer revisions of this device. This has
been reported in Arch Linux and Fedora. The original patch was tested on
devices with bcdDevice of 1.60, whereas the newer devices report bcdDevice
as 2.20. Limit the UNUSUAL_DEV entry to devices less than 2.20.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=909591
The Arch Forum post on this is here:
https://bbs.archlinux.org/viewtopic.php?id=152011
Reported-by: Carsten S. <carsteniq@yahoo.com>
Tested-by: Carsten S. <carsteniq@yahoo.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd060956c5e97931c3909e4a808508469c0bb9f6 upstream.
1. The idProduct is little endian, so make sure its value to be
compatible with the current CPU. Make no break on big endian processors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04753523266629b1cd0518091da1658755787198 upstream.
The module alias should be "ehci-omap" and not
"omap-ehci" to match the platform device name.
The omap-ehci module should now autoload correctly.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1f3f687722fd9b29a0c2a85b4844e3b2a3585c63 upstream.
The USB device descriptor of one identity presented by a few
Huawei morphing devices have serial functions with class codes
02/02/ff, indicating CDC ACM with a vendor specific protocol. This
combination is often used for MSFT RNDIS functions, and the CDC
ACM class driver will therefore ignore such functions.
The CDC ACM class driver cannot support functions with only 2
endpoints. The underlying serial functions of these modems are
also believed to be the same as for alternate device identities
already supported by the option driver. Letting the same driver
handle these functions independently of the current identity
ensures consistent handling and user experience.
There is no need to blacklist these devices in the rndis_host
driver. Huawei serial functions will either have only 2 endpoints
or a CDC ACM functional descriptor with bmCapabilities != 0, making
them correctly ignored as "non RNDIS" by that driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd565279e51bedee1b2988e84f9b3bef485adeb6 upstream.
Interface layout:
00 CD-ROM
01 debug COM port
02 AP control port
03 modem
04 usb-ethernet
Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0408 ProdID=ea42 Rev= 0.00
S: Manufacturer=Qualcomm, Incorporated
S: Product=Qualcomm CDMA Technologies MSM
S: SerialNumber=353568051xxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8f0302bbcbd1b14655bef29f6996a2152be559d upstream.
Adding three currently unsupported modems based on information
from .inf driver files:
Diag VID_1BBB&PID_0052&MI_00
AGPS VID_1BBB&PID_0052&MI_01
VOICE VID_1BBB&PID_0052&MI_02
AT VID_1BBB&PID_0052&MI_03
Modem VID_1BBB&PID_0052&MI_05
wwan VID_1BBB&PID_0052&MI_06
Diag VID_1BBB&PID_00B6&MI_00
AT VID_1BBB&PID_00B6&MI_01
Modem VID_1BBB&PID_00B6&MI_02
wwan VID_1BBB&PID_00B6&MI_03
Diag VID_1BBB&PID_00B7&MI_00
AGPS VID_1BBB&PID_00B7&MI_01
VOICE VID_1BBB&PID_00B7&MI_02
AT VID_1BBB&PID_00B7&MI_03
Modem VID_1BBB&PID_00B7&MI_04
wwan VID_1BBB&PID_00B7&MI_05
Updating the blacklist info for the X060S_X200 and X220_X500D,
reserving interfaces for a wwan driver, based on
wwan VID_1BBB&PID_0000&MI_04
wwan VID_1BBB&PID_0017&MI_06
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b2ca699076573c94fee9a73cb0d8645383b602a0 upstream.
Make sure serial-driver dtr_rts is called with disc_mutex held after
checking the disconnected flag.
Due to a bug in the tty layer, dtr_rts may get called after a device has
been disconnected and the tty-device unregistered. Some drivers have had
individual checks for disconnect to make sure the disconnected interface
was not accessed, but this should really be handled in usb-serial core
(at least until the long-standing tty-bug has been fixed).
Note that the problem has been made more acute with commit 0998d0631001
("device-core: Ensure drvdata = NULL when no driver is bound") as the
port data is now also NULL when dtr_rts is called resulting in further
oopses.
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58b2939b4d5a030eaec469d29812ab8477ee7e76 upstream.
When the xHCI driver is not available, actively switch the ports to EHCI
mode since some BIOSes leave them in xHCI mode where they would
otherwise appear dead. This was discovered on a Dell Optiplex 7010,
but it's possible other systems could be affected.
This should be backported to kernels as old as 3.0, that contain the
commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: David Moore <david.moore@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48c3375c5f69b1c2ef3d1051a0009cb9bce0ce24 upstream.
This patch (as1640) fixes a memory leak in xhci-hcd. The urb_priv
data structure isn't always deallocated in the handle_tx_event()
routine for non-control transfers. The patch adds a kfree() call so
that all paths end up freeing the memory properly.
This patch should be backported to kernels as old as 2.6.36, that
contain the commit 8e51adccd4c4b9ffcd509d7f2afce0a906139f75 "USB: xHCI:
Introduce urb_priv structure"
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-and-tested-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f18f8ed2a9adc41c2d9294b85b6af115829d2af1 upstream.
To calculate the TD size for a particular TRB in an isoc TD, we need
know the endpoint's max packet size. Isochronous endpoints also encode
the number of additional service opportunities in their wMaxPacketSize
field. The TD size calculation did not mask off those bits before using
the field. This resulted in incorrect TD size information for
isochronous TRBs when an URB frame buffer crossed a 64KB boundary.
For example:
- an isoc endpoint has 2 additional service opportunites and
a max packet size of 1020 bytes
- a frame transfer buffer contains 3060 bytes
- one frame buffer crosses a 64KB boundary, and must be split into
one 1276 byte TRB, and one 1784 byte TRB.
The TD size is is the number of packets that remain to be transferred
for a TD after processing all the max packet sized packets in the
current TRB and all previous TRBs.
For this TD, the number of packets to be transferred is (3060 / 1020),
or 3. The first TRB contains 1276 bytes, which means it contains one
full packet, and a 256 byte remainder. After processing all the max
packet-sized packets in the first TRB, the host will have 2 packets left
to transfer.
The old code would calculate the TD size for the first TRB as:
total packet count = DIV_ROUND_UP (TD length / endpoint wMaxPacketSize)
total packet count - (first TRB length / endpoint wMaxPacketSize)
The math should have been:
total packet count = DIV_ROUND_UP (3060 / 1020) = 3
3 - (1276 / 1020) = 2
Since the old code didn't mask off the additional service interval bits
from the wMaxPacketSize field, the math ended up as
total packet count = DIV_ROUND_UP (3060 / 5116) = 1
1 - (1276 / 5116) = 1
Fix this by masking off the number of additional service opportunities
in the wMaxPacketSize field.
This patch should be backported to stable kernels as old as 3.0, that
contain the commit 4da6e6f247a2601ab9f1e63424e4d944ed4124f3 "xhci 1.0:
Update TD size field format." It may not apply well to kernels older
than 3.2 because of commit 29cc88979a8818cd8c5019426e945aed118b400e
"USB: use usb_endpoint_maxp() instead of le16_to_cpu()".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 760973d2a74b93eb1697981f7448f0e62767cfc4 upstream.
An isochronous TD is comprised of one isochronous TRB chained to zero or
more normal TRBs. Only the isoc TRB has the TBC and TLBPC fields. The
normal TRBs must set those fields to zeroes. The code was setting the
TBC and TLBPC fields for both isoc and normal TRBs. Fix this.
This should be backported to stable kernels as old as 3.0, that contain
the commit b61d378f2da41c748aba6ca19d77e1e1c02bcea5 " xhci 1.0: Set
transfer burst last packet count field."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba7b5c22d33136a5612ca5ef8d31564dcc501126 upstream.
Fix incorrect bit test that originally showed up in
4ee823b83bc9851743fab756c76b27d6a1e2472b "USB/xHCI: Support
device-initiated USB 3.0 resume."
Use '&' instead of '&&'.
This should be backported to kernels as old as 3.4.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
new switch command
commit 200e0d994d9d1919b28c87f1a5fb99a8e13b8a0f upstream.
1. Optimize the match rules with new macro for Huawei USB storage devices,
to avoid to load USB storage driver for the modem interface
with Huawei devices.
2. Add to support new switch command for new Huawei USB dongles.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07c7be3d87e5cdaf5f94c271c516456364ef286c upstream.
1. Define a new macro for USB storage match rules:
matching with Vendor ID and interface descriptors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54a3ac0c9e5b7213daa358ce74d154352657353a upstream.
Usb3.0 device defines function remote wakeup which is only for interface
recipient rather than device recipient. This is different with usb2.0 device's
remote wakeup feature which is defined for device recipient. According usb3.0
spec 9.4.5, the function remote wakeup can be modified by the SetFeature()
requests using the FUNCTION_SUSPEND feature selector. This patch is to use
correct way to disable usb3.0 device's function remote wakeup after suspend
error and resuming.
This should be backported to kernels as old as 3.4, that contain the
commit 623bef9e03a60adc623b09673297ca7a1cdfb367 "USB/xhci: Enable remote
wakeup for USB3 devices."
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e619d04159be54b3daa0b7036b0ce9e067f4b5d upstream.
This patch (as1654) fixes a very old bug in ehci-hcd, connected with
scheduling of periodic split transfers. The calculations for
full/low-speed bus usage are all carried out after the correction for
bit-stuffing has been applied, but the values in the max_tt_usecs
array assume it hasn't been. The array should allow for allocation of
up to 90% of the bus capacity, which is 900 us, not 780 us.
The symptom caused by this bug is that any isochronous transfer to a
full-speed device with a maxpacket size larger than about 980 bytes is
always rejected with a -ENOSPC error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee74290b7853db9d5fd64db70e5c175241c59fba upstream.
This patch (as1652) fixes a long-standing bug in ehci-hcd. The driver
relies on status polls to know when to stop port-resume signalling.
It uses the root-hub status timer to schedule these status polls. But
when the driver for the root hub is resumed, the timer is rescheduled
to go off immediately -- before the port is ready. When this happens
the timer does not get re-enabled, which prevents the port resume from
finishing until some other event occurs.
The symptom is that when a new device is plugged in, it doesn't get
recognized or enumerated until lsusb is run or something else happens.
The solution is to re-enable the root-hub status timer after every
status poll while a port resume is in progress.
This bug hasn't surfaced before now because we never used to try to
suspend the root hub in the middle of a port resume (except by
coincidence).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Norbert Preining <preining@logic.at>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78796ae17eacedcdcaaeb03ba73d2e532a4c8f83 upstream.
Add VID and PID for Telit Gobi QDL device
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4fa681541aa7bf8570d03426dd7ba663a71c467 upstream.
New device with 3 serial interfaces:
If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend) Sub=ff Prot=ff
If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend) Sub=ff Prot=ff
If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend) Sub=ff Prot=ff
If#= 3 Alt= 0 #EPs= 2 Cls=08(stor) Sub=06 Prot=50
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03eb466f276ceef9dcf023dc5474db02af68aad9 upstream.
Add PID and special handling for Telit LE920
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c249f911406efcc7456cb4af79396726bf7b8c57 upstream.
Add PID/VID entries for ELV WS 300 PC II weather station
Signed-off-by: Sven Killig <sven@killig.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ba3b2ccc72b3df5c305d61f59d93ab0f0e87991 upstream.
Add support for Zolix Omni 1509 monochromator custom USB-RS232 converter.
Signed-off-by: Petr Kubánek <petr@kubanek.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6048e4c69d80600baba35856651056860d5d8f5a upstream.
dwc3_gadget_set_ep_config expects maxburst as incremented by 1. So, by
default initialize ep->maxburst to 1 for ep0.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0f815a0a700bc10547449bde6c106051a035a1b9 upstream.
This patch (as1644) fixes a race that occurs during startup in
uhci-hcd. If the IRQ line is shared with other devices, it's possible
for the handler routine to be called before the data structures are
fully initialized.
The problem is fixed by adding a check to the IRQ handler routine. If
the initialization hasn't finished yet, the routine will return
immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: "Huang, Adrian (ISS Linux TW)" <adrian.huang@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Bjørn Mork <bjorn@mork.no>
commit 2291dff02e5f8c708a46a7c4c888f2c467e26642 upstream.
The driver description files gives these names to the vendor specific
functions on this modem:
Diag VID_19D2&PID_0265&MI_00
NMEA VID_19D2&PID_0265&MI_01
AT cmd VID_19D2&PID_0265&MI_02
Modem VID_19D2&PID_0265&MI_03
Net VID_19D2&PID_0265&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99beb2e9687ffd61c92a9875141eabe6f57a71b9 upstream.
The driver description files gives these names to the vendor specific
functions on this modem:
Diagnostics VID_2357&PID_0201&MI_00
NMEA VID_2357&PID_0201&MI_01
Modem VID_2357&PID_0201&MI_03
Networkcard VID_2357&PID_0201&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36caff5d795429c572443894e8789c2150dd796b upstream.
This patch (as1631) fixes a bug that shows up when a config change
fails for a device under an xHCI controller. The controller needs to
be told to disable the endpoints that have been enabled for the new
config. The existing code does this, but before storing the
information about which endpoints were enabled! As a result, any
second attempt to install the new config is doomed to fail because
xhci-hcd will refuse to enable an endpoint that is already enabled.
The patch optimistically initializes the new endpoints' device
structures before asking the device to switch to the new config. If
the request fails then the endpoint information is already stored, so
we can use usb_hcd_alloc_bandwidth() to disable the endpoints with no
trouble. The rest of the error path is slightly more complex now; we
have to disable the new interfaces and call put_device() rather than
simply deallocating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Matthias Schniedermeyer <ms@citd.de>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 55c1945edaac94c5338a3647bc2e85ff75d9cf36 upstream.
A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK. If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).
The xHCI code to compute the NAK interval does not handle the special
case of zero properly. The current code unconditionally subtracts one
from bInterval and uses it as an exponent. This causes a very large
bInterval to be used, and warning messages like these will be printed:
usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes
This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.
This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07e72b95f5038cc82304b9a4a2eb7f9fc391ea68 upstream.
Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c52804a472649b2e5005342308739434cbd51119 upstream.
The USB core hub thread (khubd) is designed with external USB hubs in
mind. It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.
The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits. When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event. If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.
This means that the hub code may lose port status changes because of
race conditions between clearing change bits. The user sees this as a
"dead port" that doesn't react to device connects.
The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.
We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's. Instead, stop the port polling timer, and
unconditionally restart it when the host resumes. If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.
This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit
0f2a79300a1471cf92ab43af165ea13555c8b0a5 "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65bdac5effd15d6af619b3b7218627ef4d84ed6a upstream.
An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train. In that case, we
issue a warm reset. Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.
The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded. This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.
Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes. Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.
Make hub_events disable the port if warm reset fails. This will disable
the port, and then bring it back into the RxDetect state. Make the USB
core ignore the connect change until the device reconnects.
Note that this patch does NOT handle connected devices slipping into the
Inactive state very well. This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure. However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.
This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm
reset logic"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f43447e62b37ee19c82a13f72f35b1ca60a74d3 upstream.
The port reset code bails out early if the current connect status is
cleared (device disconnected). If we're issuing a hot reset, it may
also look at the link state before the reset is finished.
Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the
Error state or Resetting state, the port connection bit retains the
value from the previous state. Therefore we can't trust it until the
reset finishes. Also, the xHCI spec section 4.19.1.2.5 says software
shall ignore the link state while the port is resetting, as it can be in
an unknown state.
The port state during reset is also unknown for USB 2.0 hubs. The hub
sends a reset signal by driving the bus into an SE0 state. This
overwhelms the "connect" signal from the device, so the port can't tell
whether anything is connected or not.
Fix the port reset code to ignore the port link state and current
connect bit until the reset finishes, and USB_PORT_STAT_RESET is
cleared.
Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case,
because it's redundant. When the warm reset finishes, the port reset
bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set.
Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit
in the code to deal with the finished reset.
This patch should be backported to all stable kernels.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 77c7f072c87fa951e9a74805febf26466f31170c upstream.
John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete. The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41e7e056cdc662f704fa9262e5c6e213b4ab45dd upstream.
If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port. Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects. To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.
The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes. We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect. However,
external USB 3.0 hubs don't need this code. They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set. Therefore it doesn't make sense to
put this code in the USB core.
This patch is part of a series to fix several reports of infinite loops
on device enumeration failure. This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller. The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.
This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm
reset logic"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8b8132bc3d1cc3d4c0687e4d638a482fa920d98a upstream.
When the USB core finishes reseting a USB device, the xHCI driver sends
a Reset Device command to the host. The xHC then updates its internal
representation of the USB device to the 'Default' device state. If the
device was already in the Default state, the xHC will complete the
command with an error status.
If a device needs to be reset several times during enumeration, the
second reset will always fail because of the xHCI Reset Device command.
This can cause issues during enumeration.
For example, usb_reset_and_verify_device calls into hub_port_init in a
loop. Say that on the first call into hub_port_init, the device is
successfully reset, but doesn't respond to several set address control
transfers. Then the port will be disabled, but the udev will remain in
tact. usb_reset_and_verify_device will call into hub_port_init again.
On the second call into hub_port_init, the device will be reset, and the
xHCI driver will issue a Reset Device command. This command will fail
(because the device is already in the Default state), and
usb_reset_and_verify_device will fail. The port will be disabled, and
the device won't be able to enumerate.
Fix this by ignoring the return value of the HCD reset_device callback.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c7439c61fa6516419c32a9824976334ea969d47 upstream.
USB 3.0 hubs and roothubs will automatically transition a failed hot
reset to a warm (BH) reset. In that case, the warm reset change bit
will be set, and the link state change bit may also be set. Change
hub_port_finish_reset to unconditionally clear those change bits for USB
3.0 hubs. If these bits are not cleared, we may lose port change events
from the roothub.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ac788f705e5118dd45204e7a5bc8d5bb6873835 upstream.
Commit 5c8a86e10a7c164f44537fabdc169fd8b4e7a440 (usb: musb: drop unneeded
musb_debug trickery) erroneously removed '\n' from the driver's banner.
Concatenate all the banner substrings while adding it back...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d16638e3b9cc195bac18a8fcbca748f33c1bc24 upstream.
If we do have endpoints named like "ep-a" then bEndpointAddress is
counted internally by the gadget framework.
If we do have endpoints named like "ep-1" then bEndpointAddress is
assigned from the digit after "ep-".
If we do have both, then it is likely that after we used up the
"generic" endpoints we will use the digits and thus assign one
bEndpointAddress to multiple endpoints.
This theory can be proofed by using the completely enabled g_multi.
Without this patch, the mass storage won't enumerate and times out
because it shares endpoints with RNDIS.
This patch also adds fills up the endpoints list so we have in total
endpoints 1 to 15 in + out available while some of them are restricted
to certain types like BULK or ISO. Without this change the nokia gadget
won't load because the system does not provide enough (BULK) endpoints
but it did before ep-a - ep-f were removed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 036915a7a402753c05b8d0529f5fd08805ab46d0 upstream.
Adding support "PSC Scanning, Magellan 800i" in cdc-acm
Very simple, but very necessary.
Suitable for all versions of the kernel > 2.6
Signed-off-by: Denis N Ladin <denladin@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8cf65dc386f3634a43312f436cc7a935476a40c4 upstream.
Simple fix to add support for Crucible Technologies COMET Caller ID
USB decoder - a device containing FTDI USB/Serial converter chip,
handling 1200bps CallerID messages decoded from the phone line -
adding correct USB PID is sufficient.
Tested to apply cleanly and work flawlessly against 3.6.9, 3.7.0-rc8
and 3.8.0-rc3 on both amd64 and x86 arches.
Signed-off-by: Tomasz Mloduchowski <q@qdot.me>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ec0085440ef8c2cf50002b34d5a504ee12aa2bf upstream.
also known as Alcatel One Touch L100V LTE
The driver description files gives these names to the vendor specific
functions on this modem:
Application1: VID_1BBB&PID_011E&MI_00
Application2: VID_1BBB&PID_011E&MI_01
Modem: VID_1BBB&PID_011E&MI_03
Ethernet: VID_1BBB&PID_011E&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94a85b633829b946eef53fc1825d526312fb856f upstream.
In option.c, add some new MEDIATEK PIDs support for MEDIATEK new products. This
is a MEDIATEK inc. release patch.
Signed-off-by: Quentin.Li <snowmanli88@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fab38246f318edcd0dcb8fd3852a47cf8938878a upstream.
The driver description files gives these names to the vendor specific
functions on this modem:
diag: VID_19D2&PID_0284&MI_00
nmea: VID_19D2&PID_0284&MI_01
at: VID_19D2&PID_0284&MI_02
mdm: VID_19D2&PID_0284&MI_03
net: VID_19D2&PID_0284&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ad86e58661b38b279b7519d4e49c7a19dc1654bb upstream.
Hyundai Petatel Inc. Nexpring NP10T terminal (EV-DO rev.A USB modem) ID
Signed-off-by: Denis Kaganovich <mahatma@eu.by>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb1e5dd7113d2fd178d3af9aca8f480ae0468edf upstream.
Like Lynx Point, Lynx Point LP is also switchable. See
1c12443ab8eba71a658fae4572147e56d1f84f66 for more details.
This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Russell Webb <russell.webb@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Mode Patch
commit b0e4e606ff6ff26da0f60826e75577b56ba4e463 upstream.
This minor patch creates a more stricter conditional for the Z1 sytems for applying
the Compliance Mode Patch, this to avoid the quirk to be applied to models that
contain a "Z1" in their dmi product string but are different from Z1 systems.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 68e5254adb88bede68285f11fb442a4d34fb550c upstream.
xhci_alloc_segments_for_ring() builds a list of xhci_segments and links
the tail to head at the end (forming a ring). When it bails out for OOM
reasons half-way through, it tries to destroy its half-built list with
xhci_free_segments_for_ring(), even though it is not a ring yet. This
causes a null-pointer dereference upon hitting the last element.
Furthermore, one of its callers (xhci_ring_alloc()) mistakenly believes
the output parameters to be valid upon this kind of OOM failure, and
calls xhci_ring_free() on them. Since the (incomplete) list/ring should
already be destroyed in that case, this would lead to a use after free.
This patch fixes those issues by having xhci_alloc_segments_for_ring()
destroy its half-built, non-circular list manually and destroying the
invalid struct xhci_ring in xhci_ring_alloc() with a plain kfree().
This patch should be backported to kernels as old as 2.6.31, that
contains the commit 0ebbab37422315a5d0cb29792271085bafdf38c0 "USB: xhci:
Ring allocation and initialization."
A separate patch will need to be developed for kernels older than 3.4,
since the ring allocation code was refactored in that kernel.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4525c0a10dff7ad3669763c28016c7daffc3900e upstream.
The xHCI 1.0 specification made a change to the TD Size field in TRBs.
The value is now the number of packets that remain to be sent in the TD,
not including this TRB. The TD Size value for the last TRB in a TD must
always be zero.
The xHCI function xhci_v1_0_td_remainder() attempts to calculate this,
but it gets it wrong. First, it erroneously reuses the old
xhci_td_remainder function, which will right shift the value by 10. The
xHCI 1.0 spec as of June 2011 says nothing about right shifting by 10.
Second, it does not set the TD size for the last TRB in a TD to zero.
Third, it uses roundup instead of DIV_ROUND_UP. The total packet count
is supposed to be the total number of bytes in this TD, divided by the
max packet size, rounded up. DIV_ROUND_UP is the right function to use
in that case.
With the old code, a TD on an endpoint with max packet size 1024 would
be set up like so:
TRB 1, TRB length = 600 bytes, TD size = 0
TRB 1, TRB length = 200 bytes, TD size = 0
TRB 1, TRB length = 100 bytes, TD size = 0
With the new code, the TD would be set up like this:
TRB 1, TRB length = 600 bytes, TD size = 1
TRB 1, TRB length = 200 bytes, TD size = 1
TRB 1, TRB length = 100 bytes, TD size = 0
This commit should be backported to kernels as old as 3.0, that contain
the commit 4da6e6f247a2601ab9f1e63424e4d944ed4124f3 "xhci 1.0: Update TD
size field format."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Chintan Mehta <chintan.mehta@sibridgetech.com>
Reported-by: Shimmer Huang <shimmering.h@gmail.com>
Tested-by: Bhavik Kothari <bhavik.kothari@sibridgetech.com>
Tested-by: Shimmer Huang <shimmering.h@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 392a07ae3316f2b90b39ce41e66d6f6b5c95de90 upstream.
David reports that at drivers/usb/host/xhci.c:2257:
static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
return (ep_type == ISOC_IN_EP || ep_type != INT_IN_EP);
}
The static analyser cppcheck says
[linux-3.7-rc2/drivers/usb/host/xhci.c:2257]: (style) Redundant condition: If ep_type == 5, the comparison ep_type != 7 is always true.
Maybe the original programmer intention was something like
static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
return (ep_type == ISOC_IN_EP || ep_type == INT_IN_EP);
}
Fix this.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 2b69899934c63b7b9432568584fb4c4a2924f40c "xhci: USB
3.0 BW checking."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8b416b0b25d5d8ddb3a91c1d20e1373582c50405 upstream.
Now that DaVinci glue layer can be modular, we must export cppi_interrupt()
that it may call...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
