summaryrefslogtreecommitdiff
path: root/drivers/usb/dwc3
AgeCommit message (Collapse)AuthorFilesLines
2024-05-17usb: dwc3: core: Prevent phy suspend during initThinh Nguyen4-52/+68
commit 6d735722063a945de56472bdc6bfcb170fd43b86 upstream. GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared during initialization. Suspend during initialization can result in undefined behavior due to clock synchronization failure, which often seen as core soft reset timeout. The programming guide recommended these bits to be cleared during initialization for DWC_usb3.0 version 1.94 and above (along with DWC_usb31 and DWC_usb32). The current check in the driver does not account if it's set by default setting from coreConsultant. This is especially the case for DRD when switching mode to ensure the phy clocks are available to change mode. Depending on the platforms/design, some may be affected more than others. This is noted in the DWC_usb3x programming guide under the above registers. Let's just disable them during driver load and mode switching. Restore them when the controller initialization completes. Note that some platforms workaround this issue by disabling phy suspend through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when they should not need to. Cc: stable@vger.kernel.org Fixes: 9ba3aca8fe82 ("usb: dwc3: Disable phy suspend after power-on reset") Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-01-26Revert "usb: dwc3: don't reset device side if dwc3 was configured as host-only"Thinh Nguyen1-2/+2
commit afe28cd686aeb77e8d9140d50fb1cf06a7ecb731 upstream. This reverts commit e835c0a4e23c38531dcee5ef77e8d1cf462658c7. Don't omit soft-reset. During initialization, the driver may need to perform a soft reset to ensure the phy is ready when the controller updates the GCTL.PRTCAPDIR or other settings by issuing phy soft-reset. Many platforms often have access to DCTL register for soft-reset despite being host-only. If there are actual reported issues from the platforms that don't expose DCTL registers, then we will need to revisit (perhaps to teach dwc3 to perform xhci's soft-reset USBCMD.HCRST). Cc: <stable@vger.kernel.org> Fixes: e835c0a4e23c ("usb: dwc3: don't reset device side if dwc3 was configured as host-only") Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/7668ab11a48f260820825274976eb41fec7f54d1.1703282469.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-01-26Revert "usb: dwc3: Soft reset phy on probe for host"Thinh Nguyen1-38/+1
commit 7059fbebcb00554c3f31e5b5d93ef6d2d96dc7b4 upstream. This reverts commit 8bea147dfdf823eaa8d3baeccc7aeb041b41944b. The phy soft reset GUSB2PHYCFG.PHYSOFTRST only applies to UTMI phy, not ULPI. This fix is incomplete. Cc: <stable@vger.kernel.org> Fixes: 8bea147dfdf8 ("usb: dwc3: Soft reset phy on probe for host") Reported-by: Köry Maincent <kory.maincent@bootlin.com> Closes: https://lore.kernel.org/linux-usb/20231205151959.5236c231@kmaincent-XPS-13-7390 Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/29a26593a60eba727de872a3e580a674807b3339.1703282469.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-01-26usb: dwc: ep0: Update request status in dwc3_ep0_stall_restartUttkarsh Aggarwal1-1/+4
commit e9d40b215e38480fd94c66b06d79045717a59e9c upstream. Current implementation blocks the running operations when Plug-out and Plug-In is performed continuously, process gets stuck in dwc3_thread_interrupt(). Code Flow: CPU1 ->Gadget_start ->dwc3_interrupt ->dwc3_thread_interrupt ->dwc3_process_event_buf ->dwc3_process_event_entry ->dwc3_endpoint_interrupt ->dwc3_ep0_interrupt ->dwc3_ep0_inspect_setup ->dwc3_ep0_stall_and_restart By this time if pending_list is not empty, it will get the next request on the given list and calls dwc3_gadget_giveback which will unmap request and call its complete() callback to notify upper layers that it has completed. Currently dwc3_gadget_giveback status is set to -ECONNRESET, whereas it should be -ESHUTDOWN based on condition if not dwc->connected is true. Cc: <stable@vger.kernel.org> Fixes: d742220b3577 ("usb: dwc3: ep0: giveback requests on stall_and_restart") Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com> Link: https://lore.kernel.org/r/20231222094704.20276-1-quic_uaggarwa@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-12-08USB: dwc3: qcom: fix wakeup after probe deferralJohan Hovold1-4/+4
commit 41f5a0973259db9e4e3c9963d36505f80107d1a0 upstream. The Qualcomm glue driver is overriding the interrupt trigger types defined by firmware when requesting the wakeup interrupts during probe. This can lead to a failure to map the DP/DM wakeup interrupts after a probe deferral as the firmware defined trigger types do not match the type used for the initial mapping: irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000! irq: type mismatch, failed to map hwirq-15 for interrupt-controller@b220000! Fix this by not overriding the firmware provided trigger types when requesting the wakeup interrupts. Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver") Cc: stable@vger.kernel.org # 4.18 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20231120161607.7405-3-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-12-08usb: dwc3: set the dma max_seg_sizeRicardo Ribalda1-0/+2
commit 8bbae288a85abed6a1cf7d185d8b9dc2f5dcb12c upstream. Allow devices to have dma operations beyond 4K, and avoid warnings such as: DMA-API: dwc3 a600000.usb: mapping sg segment longer than device claims to support [len=86016] [max=65536] Cc: stable@vger.kernel.org Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Reported-by: Zubin Mithra <zsm@chromium.org> Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20231026-dwc3-v2-1-1d4fd5c3e067@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-12-08usb: dwc3: Fix default mode initializationAlexander Stein1-1/+1
commit 10d510abd096d620b9fda2dd3e0047c5efc4ad2b upstream. The default mode, configurable by DT, shall be set before usb role switch driver is registered. Otherwise there is a race between default mode and mode set by usb role switch driver. Fixes: 98ed256a4dbad ("usb: dwc3: Add support for role-switch-default-mode binding") Cc: stable <stable@kernel.org> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20231025095110.2405281-1-alexander.stein@ew.tq-group.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-12-08USB: dwc3: qcom: fix ACPI platform device leakJohan Hovold1-7/+30
[ Upstream commit 9cf87666fc6e08572341fe08ecd909935998fbbd ] Make sure to free the "urs" platform device, which is created for some ACPI platforms, on probe errors and on driver unbind. Compile-tested only. Fixes: c25c210f590e ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot") Cc: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Andrew Halaney <ahalaney@redhat.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Link: https://lore.kernel.org/r/20231117173650.21161-4-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-12-08USB: dwc3: qcom: fix resource leaks on probe deferralJohan Hovold1-3/+6
[ Upstream commit 51392a1879ff06dc21b68aef4825f6ef68a7be42 ] The driver needs to deregister and free the newly allocated dwc3 core platform device on ACPI probe errors (e.g. probe deferral) and on driver unbind but instead it leaked those resources while erroneously dropping a reference to the parent platform device which is still in use. For OF probing the driver takes a reference to the dwc3 core platform device which has also always been leaked. Fix the broken ACPI tear down and make sure to drop the dwc3 core reference for both OF and ACPI. Fixes: 8fd95da2cfb5 ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()") Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI") Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver") Cc: stable@vger.kernel.org # 4.18 Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Lee Jones <lee@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 9cf87666fc6e ("USB: dwc3: qcom: fix ACPI platform device leak") Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-10-25usb: dwc3: Soft reset phy on probe for hostThinh Nguyen1-1/+38
commit 8bea147dfdf823eaa8d3baeccc7aeb041b41944b upstream. When there's phy initialization, we need to initiate a soft-reset sequence. That's done through USBCMD.HCRST in the xHCI driver and its initialization, However, the dwc3 driver may modify core configs before the soft-reset. This may result in some connection instability. So, ensure the phy is ready before the controller updates the GCTL.PRTCAPDIR or other settings by issuing phy soft-reset. Note that some host-mode configurations may not expose device registers to initiate the controller soft-reset (via DCTL.CoreSftRst). So we reset through GUSB3PIPECTL and GUSB2PHYCFG instead. Cc: stable@vger.kernel.org Fixes: e835c0a4e23c ("usb: dwc3: don't reset device side if dwc3 was configured as host-only") Reported-by: Kenta Sato <tosainu.maple@gmail.com> Closes: https://lore.kernel.org/linux-usb/ZPUciRLUcjDywMVS@debian.me/ Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Tested-by: Kenta Sato <tosainu.maple@gmail.com> Link: https://lore.kernel.org/r/70aea513215d273669152696cc02b20ddcdb6f1a.1694564261.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-19usb: dwc3: meson-g12a: do post init to fix broken usb after resumptionLuke Lu1-0/+6
commit 1fa206bb764f37d2ab4bf671e483153ef0659b34 upstream. Device connected to usb otg port of GXL-based boards can not be recognised after resumption, doesn't recover even if disconnect and reconnect the device. dmesg shows it disconnects during resumption. [ 41.492911] usb 1-2: USB disconnect, device number 3 [ 41.499346] usb 1-2: unregistering device [ 41.511939] usb 1-2: unregistering interface 1-2:1.0 Calling usb_post_init() will fix this issue, and it's tested and verified on libretech's aml-s905x-cc board. Cc: stable@vger.kernel.org # v5.8+ Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue") Signed-off-by: Luke Lu <luke.lu@libre.computer> Acked-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20230809212911.18903-1-luke.lu@libre.computer Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-26USB: dwc3: qcom: fix NULL-deref on suspendJohan Hovold1-1/+10
[ Upstream commit d2d69354226de0b333d4405981f3d9c41ba8430a ] The Qualcomm dwc3 glue driver is currently accessing the driver data of the child core device during suspend and on wakeup interrupts. This is clearly a bad idea as the child may not have probed yet or could have been unbound from its driver. The first such layering violation was part of the initial version of the driver, but this was later made worse when the hack that accesses the driver data of the grand child xhci device to configure the wakeup interrupts was added. Fixing this properly is not that easily done, so add a sanity check to make sure that the child driver data is non-NULL before dereferencing it for now. Note that this relies on subtleties like the fact that driver core is making sure that the parent is not suspended while the child is probing. Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/all/20230325165217.31069-4-manivannan.sadhasivam@linaro.org/ Fixes: d9152161b4bf ("usb: dwc3: Add Qualcomm DWC3 glue layer driver") Fixes: 6895ea55c385 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend") Cc: stable@vger.kernel.org # 3.18: a872ab303d5d: "usb: dwc3: qcom: fix use-after-free on runtime-PM wakeup" Cc: Sandeep Maheswaram <quic_c_sanm@quicinc.com> Cc: Krishna Kurapati <quic_kriskura@quicinc.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Message-ID: <20230607100540.31045-2-johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-08-16usb: dwc3: Properly handle processing of pending eventsElson Roy Serrao1-1/+8
commit 3ddaa6a274578e23745b7466346fc2650df8f959 upstream. If dwc3 is runtime suspended we defer processing the event buffer until resume, by setting the pending_events flag. Set this flag before triggering resume to avoid race with the runtime resume callback. While handling the pending events, in addition to checking the event buffer we also need to process it. Handle this by explicitly calling dwc3_thread_interrupt(). Also balance the runtime pm get() operation that triggered this processing. Cc: stable@vger.kernel.org Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM") Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20230801192658.19275-1-quic_eserrao@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-11usb: dwc3: don't reset device side if dwc3 was configured as host-onlyJisheng Zhang1-2/+2
commit e835c0a4e23c38531dcee5ef77e8d1cf462658c7 upstream. Commit c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode") replaces check for HOST only dr_mode with current_dr_role. But during booting, the current_dr_role isn't initialized, thus the device side reset is always issued even if dwc3 was configured as host-only. What's more, on some platforms with host only dwc3, aways issuing device side reset by accessing device register block can cause kernel panic. Fixes: c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode") Cc: stable <stable@kernel.org> Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-11usb: dwc3: pci: skip BYT GPIO lookup table for hardwired phyGratian Crisan1-2/+4
commit b32b8f2b9542d8039f5468303a6ca78c1b5611a5 upstream. Hardware based on the Bay Trail / BYT SoCs require an external ULPI phy for USB device-mode. The phy chip usually has its 'reset' and 'chip select' lines connected to GPIOs described by ACPI fwnodes in the DSDT table. Because of hardware with missing ACPI resources for the 'reset' and 'chip select' GPIOs commit 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources") introduced a fallback gpiod_lookup_table with hard-coded mappings for Bay Trail devices. However there are existing Bay Trail based devices, like the National Instruments cRIO-903x series, where the phy chip has its 'reset' and 'chip-select' lines always asserted in hardware via resistor pull-ups. On this hardware the phy chip is always enabled and the ACPI dsdt table is missing information not only for the 'chip-select' and 'reset' lines but also for the BYT GPIO controller itself "INT33FC". With the introduction of the gpiod_lookup_table initializing the USB device-mode on these hardware now errors out. The error comes from the gpiod_get_optional() calls in dwc3_pci_quirks() which will now return an -ENOENT error due to the missing ACPI entry for the INT33FC gpio controller used in the aforementioned table. This hardware used to work before because gpiod_get_optional() will return NULL instead of -ENOENT if no GPIO has been assigned to the requested function. The dwc3_pci_quirks() code for setting the 'cs' and 'reset' GPIOs was then skipped (due to the NULL return). This is the correct behavior in cases where the phy chip is hardwired and there are no GPIOs to control. Since the gpiod_lookup_table relies on the presence of INT33FC fwnode in ACPI tables only add the table if we know the entry for the INT33FC gpio controller is present. This allows Bay Trail based devices with hardwired dwc3 ULPI phys to continue working. Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources") Cc: stable <stable@kernel.org> Signed-off-by: Gratian Crisan <gratian.crisan@ni.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230726184555.218091-2-gratian.crisan@ni.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-11Revert "usb: dwc3: core: Enable AutoRetry feature in the controller"Jakub Vanek2-19/+0
commit 734ae15ab95a18d3d425fc9cb38b7a627d786f08 upstream. This reverts commit b138e23d3dff90c0494925b4c1874227b81bddf7. AutoRetry has been found to sometimes cause controller freezes when communicating with buggy USB devices. This controller feature allows the controller in host mode to send non-terminating/burst retry ACKs instead of terminating retry ACKs to devices when a transaction error (CRC error or overflow) occurs. Unfortunately, if the USB device continues to respond with a CRC error, the controller will not complete endpoint-related commands while it keeps trying to auto-retry. [3] The xHCI driver will notice this once it tries to abort the transfer using a Stop Endpoint command and does not receive a completion in time. [1] This situation is reported to dmesg: [sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN [sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00 xhci-hcd: xHCI host not responding to stop endpoint command xhci-hcd: xHCI host controller not responding, assume dead xhci-hcd: HC died; cleaning up Some users observed this problem on an Odroid HC2 with the JMS578 USB3-to-SATA bridge. The issue can be triggered by starting a read-heavy workload on an attached SSD. After a while, the host controller would die and the SSD would disappear from the system. [1] Further analysis by Synopsys determined that controller revisions other than the one in Odroid HC2 are also affected by this. The recommended solution was to disable AutoRetry altogether. This change does not have a noticeable performance impact. [2] Revert the enablement commit. This will keep the AutoRetry bit in the default state configured during SoC design [2]. Fixes: b138e23d3dff ("usb: dwc3: core: Enable AutoRetry feature in the controller") Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1] Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2] Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3] Cc: stable@vger.kernel.org Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Jakub Vanek <linuxtardis@gmail.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-27usb: dwc3-meson-g12a: Fix an error handling path in dwc3_meson_g12a_probe()Christophe JAILLET1-1/+4
[ Upstream commit 01052b91c9808e3c3b068ae2721cb728ec9aa4c0 ] If dwc3_meson_g12a_otg_init() fails, resources allocated by the previous of_platform_populate() call should be released, as already done in the error handling path. Fixes: 1e355f21d3fb ("usb: dwc3: Add Amlogic A1 DWC3 glue") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Message-ID: <9d28466de1808ccc756b4cc25fc72c482d133d13.1686403934.git.christophe.jaillet@wanadoo.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-07-27usb: dwc3: qcom: Fix an error handling path in dwc3_qcom_probe()Christophe JAILLET1-2/+3
[ Upstream commit 4a944da707123686d372ec01ea60056902fadf35 ] If dwc3_qcom_create_urs_usb_platdev() fails, some resources still need to be released, as already done in the other error handling path of the probe. Fixes: c25c210f590e ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Message-ID: <b69fa8dd68d816e7d24c88d3eda776ceb28c5dc5.1685890571.git.christophe.jaillet@wanadoo.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-07-27usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()Christophe JAILLET1-1/+5
[ Upstream commit 8fd95da2cfb5046c4bb5a3cdc9eb7963ba8b10dd ] In the probe, some resources are allocated with dwc3_qcom_of_register_core() or dwc3_qcom_acpi_register_core(). The corresponding resources are already coorectly freed in the error handling path of the probe, but not in the remove function. Fix it. Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Message-ID: <c0215a84cdf18fb3514c81842783ec53cf149deb.1685891059.git.christophe.jaillet@wanadoo.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-07-27usb: dwc3: qcom: Fix potential memory leakVladislav Efanov1-3/+3
[ Upstream commit 097fb3ee710d4de83b8d4f5589e8ee13e0f0541e ] Function dwc3_qcom_probe() allocates memory for resource structure which is pointed by parent_res pointer. This memory is not freed. This leads to memory leak. Use stack memory to prevent memory leak. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI") Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru> Acked-by: Shawn Guo <shawn.guo@linaro.org> Link: https://lore.kernel.org/r/20230517172518.442591-1-VEfanov@ispras.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-07-27usb: dwc3: gadget: Propagate core init errors to UDC during pullupKrishna Kurapati1-1/+3
commit c0aabed9cabe057309779a9e26fe86a113d24dad upstream. In scenarios where pullup relies on resume (get sync) to initialize the controller and set the run stop bit, then core_init is followed by gadget_resume which will eventually set run stop bit. But in cases where the core_init fails, the return value is not sent back to udc appropriately. So according to UDC the controller has started but in reality we never set the run stop bit. On systems like Android, there are uevents sent to HAL depending on whether the configfs_bind / configfs_disconnect were invoked. In the above mentioned scnenario, if the core init fails, the run stop won't be set and the cable plug-out won't result in generation of any disconnect event and userspace would never get any uevent regarding cable plug out and we never call pullup(0) again. Furthermore none of the next Plug-In/Plug-Out's would be known to configfs. Return back the appropriate result to UDC to let the userspace/ configfs know that the pullup failed so they can take appropriate action. Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded") Cc: stable <stable@kernel.org> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Message-ID: <20230618120949.14868-1-quic_kriskura@quicinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-06-21usb: dwc3: gadget: Reset num TRBs before giving back the requestElson Roy Serrao1-0/+1
commit 00f8205ffcf112dcef14f8151d78075d38d22c08 upstream. Consider a scenario where cable disconnect happens when there is an active usb reqest queued to the UDC. As part of the disconnect we would issue an end transfer with no interrupt-on-completion before giving back this request. Since we are giving back the request without skipping TRBs the num_trbs field of dwc3_request still holds the stale value previously used. Function drivers re-use same request for a given bind-unbind session and hence their dwc3_request context gets preserved across cable disconnect/connect. When such a request gets re-queued after cable connect, we would increase the num_trbs field on top of the previous stale value thus incorrectly representing the number of TRBs used. Fix this by resetting num_trbs field before giving back the request. Fixes: 09fe1f8d7e2f ("usb: dwc3: gadget: track number of TRBs per request") Cc: stable <stable@kernel.org> Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Message-ID: <1685654850-8468-1-git-send-email-quic_eserrao@quicinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-05-30usb: dwc3: debugfs: Resume dwc3 before accessing registersUdipto Goswami1-0/+109
commit 614ce6a2ea50068b45339257891e51e639ac9001 upstream. When the dwc3 device is runtime suspended, various required clocks are in disabled state and it is not guaranteed that access to any registers would work. Depending on the SoC glue, a register read could be as benign as returning 0 or be fatal enough to hang the system. In order to prevent such scenarios of fatal errors, make sure to resume dwc3 then allow the function to proceed. Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Cc: stable@vger.kernel.org #3.2: 30332eeefec8: debugfs: regset32: Add Runtime PM support Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230509144836.6803-1-quic_ugoswami@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-05-17usb: dwc3: gadget: Change condition for processing suspend eventPrashanth K1-9/+2
[ Upstream commit 4decf4060ecfee1f7a710999fcd421645ac0c419 ] Currently we process the suspend interrupt event only if the device is in configured state. Consider a case where device is not configured and got suspend interrupt, in that case our gadget will still use 100mA as composite_suspend didn't happen. But battery charging specification (BC1.2) expects a downstream device to draw less than 2.5mA when unconnected OR suspended. Fix this by removing the condition for processing suspend event, and thus composite_resume would set vbus draw to 2. Fixes: 72704f876f50 ("dwc3: gadget: Implement the suspend entry event handler") Signed-off-by: Prashanth K <quic_prashk@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/1677217619-10261-2-git-send-email-quic_prashk@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-05-17USB: dwc3: fix runtime pm imbalance on unbindJohan Hovold1-0/+1
commit 44d257e9012ee8040e41d224d0e5bfb5ef5427ea upstream. Make sure to balance the runtime PM usage count on driver unbind by adding back the pm_runtime_allow() call that had been erroneously removed. Fixes: 266d0493900a ("usb: dwc3: core: don't trigger runtime pm when remove driver") Cc: stable@vger.kernel.org # 5.9 Cc: Li Jun <jun.li@nxp.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-3-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-05-17USB: dwc3: fix runtime pm imbalance on probe errorsJohan Hovold1-9/+5
commit 9a8ad10c9f2e0925ff26308ec6756b93fc2f4977 upstream. Make sure not to suspend the device when probe fails to avoid disabling clocks and phys multiple times. Fixes: 328082376aea ("usb: dwc3: fix runtime PM in error path") Cc: stable@vger.kernel.org # 4.8 Cc: Roger Quadros <rogerq@ti.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-05usb: dwc3: gadget: Add 1ms delay after end transfer command without IOCWesley Cheng1-3/+11
[ Upstream commit d8a2bb4eb75866275b5cf7de2e593ac3449643e2 ] Previously, there was a 100uS delay inserted after issuing an end transfer command for specific controller revisions. This was due to the fact that there was a GUCTL2 bit field which enabled synchronous completion of the end transfer command once the CMDACT bit was cleared in the DEPCMD register. Since this bit does not exist for all controller revisions and the current implementation heavily relies on utizling the EndTransfer command completion interrupt, add the delay back in for uses where the interrupt on completion bit is not set, and increase the duration to 1ms for the controller to complete the command. An issue was seen where the USB request buffer was unmapped while the DWC3 controller was still accessing the TRB. However, it was confirmed that the end transfer command was successfully submitted. (no end transfer timeout) In situations, such as dwc3_gadget_soft_disconnect() and __dwc3_gadget_ep_disable(), the dwc3_remove_request() is utilized, which will issue the end transfer command, and follow up with dwc3_gadget_giveback(). At least for the USB ep disable path, it is required for any pending and started requests to be completed and returned to the function driver in the same context of the disable call. Without the GUCTL2 bit, it is not ensured that the end transfer is completed before the buffers are unmapped. Fixes: cf2f8b63f7f1 ("usb: dwc3: gadget: Remove END_TRANSFER delay") Cc: stable <stable@kernel.org> Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230306200557.29387-1-quic_wcheng@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-04-05usb: dwc3: gadget: move cmd_endtransfer to extra functionMichael Grzeschik1-32/+37
[ Upstream commit e192cc7b52399d1b073f88cd3ba128b74d3a57f1 ] This patch adds the extra function __dwc3_stop_active_transfer to consolidate the same codepath. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Link: https://lore.kernel.org/r/20220306211251.2281335-3-m.grzeschik@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: d8a2bb4eb758 ("usb: dwc3: gadget: Add 1ms delay after end transfer command without IOC") Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-02-15usb: dwc3: qcom: enable vbus override when in OTG dr-modeNeil Armstrong1-1/+1
[ Upstream commit eb320f76e31dc835b9f57f04af1a2353b13bb7d8 ] With vbus override enabled when in OTG dr_mode, Host<->Peripheral switch now works on SM8550, otherwise the DWC3 seems to be stuck in Host mode only. Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver") Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20230123-topic-sm8550-upstream-dwc3-qcom-otg-v2-1-2d400e598463@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-02-15usb: dwc3: dwc3-qcom: Fix typo in the dwc3 vbus override APIWesley Cheng1-4/+4
[ Upstream commit 8e6cb5d27e8246d9c986ec162d066a502d2b602b ] There was an extra character in the dwc3_qcom_vbus_override_enable() function. Removed the extra character. Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210704013314.200951-2-bryan.odonoghue@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: eb320f76e31d ("usb: dwc3: qcom: enable vbus override when in OTG dr-mode") Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-01-14usb: dwc3: qcom: Fix memory leak in dwc3_qcom_interconnect_initMiaoqian Lin1-3/+10
[ Upstream commit 97a48da1619ba6bd42a0e5da0a03aa490a9496b1 ] of_icc_get() alloc resources for path handle, we should release it when not need anymore. Like the release in dwc3_qcom_interconnect_exit() function. Add icc_put() in error handling to fix this. Fixes: bea46b981515 ("usb: dwc3: qcom: Add interconnect support in dwc3 driver") Cc: stable <stable@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20221206081731.818107-1-linmq006@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-01-14usb: dwc3: core: defer probe on ulpi_read_id timeoutFerry Toth1-1/+6
commit 63130462c919ece0ad0d9bb5a1f795ef8d79687e upstream. Since commit 0f0101719138 ("usb: dwc3: Don't switch OTG -> peripheral if extcon is present"), Dual Role support on Intel Merrifield platform broke due to rearranging the call to dwc3_get_extcon(). It appears to be caused by ulpi_read_id() masking the timeout on the first test write. In the past dwc3 probe continued by calling dwc3_core_soft_reset() followed by dwc3_get_extcon() which happend to return -EPROBE_DEFER. On deferred probe ulpi_read_id() finally succeeded. Due to above mentioned rearranging -EPROBE_DEFER is not returned and probe completes without phy. On Intel Merrifield the timeout on the first test write issue is reproducible but it is difficult to find the root cause. Using a mainline kernel and rootfs with buildroot ulpi_read_id() succeeds. As soon as adding ftrace / bootconfig to find out why, ulpi_read_id() fails and we can't analyze the flow. Using another rootfs ulpi_read_id() fails even without adding ftrace. We suspect the issue is some kind of timing / race, but merely retrying ulpi_read_id() does not resolve the issue. As we now changed ulpi_read_id() to return -ETIMEDOUT in this case, we need to handle the error by calling dwc3_core_soft_reset() and request -EPROBE_DEFER. On deferred probe ulpi_read_id() is retried and succeeds. Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT") Cc: stable@vger.kernel.org Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Ferry Toth <ftoth@exalondelft.nl> Link: https://lore.kernel.org/r/20221205201527.13525-3-ftoth@exalondelft.nl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-14usb: dwc3: Fix race between dwc3_set_mode and __dwc3_set_modeSven Peter1-6/+10
commit 62c73bfea048e66168df09da6d3e4510ecda40bb upstream. dwc->desired_dr_role is changed by dwc3_set_mode inside a spinlock but then read by __dwc3_set_mode outside of that lock. This can lead to a race condition when very quick successive role switch events happen: CPU A dwc3_set_mode(DWC3_GCTL_PRTCAP_HOST) // first role switch event spin_lock_irqsave(&dwc->lock, flags); dwc->desired_dr_role = mode; // DWC3_GCTL_PRTCAP_HOST spin_unlock_irqrestore(&dwc->lock, flags); queue_work(system_freezable_wq, &dwc->drd_work); CPU B __dwc3_set_mode // .... spin_lock_irqsave(&dwc->lock, flags); // desired_dr_role is DWC3_GCTL_PRTCAP_HOST dwc3_set_prtcap(dwc, dwc->desired_dr_role); spin_unlock_irqrestore(&dwc->lock, flags); CPU A dwc3_set_mode(DWC3_GCTL_PRTCAP_DEVICE) // second event spin_lock_irqsave(&dwc->lock, flags); dwc->desired_dr_role = mode; // DWC3_GCTL_PRTCAP_DEVICE spin_unlock_irqrestore(&dwc->lock, flags); CPU B (continues running __dwc3_set_mode) switch (dwc->desired_dr_role) { // DWC3_GCTL_PRTCAP_DEVICE // .... case DWC3_GCTL_PRTCAP_DEVICE: // .... ret = dwc3_gadget_init(dwc); We then have DWC3_GCTL.DWC3_GCTL_PRTCAPDIR = DWC3_GCTL_PRTCAP_HOST and dwc->current_dr_role = DWC3_GCTL_PRTCAP_HOST but initialized the controller in device mode. It's also possible to get into a state where both host and device are intialized at the same time. Fix this race by creating a local copy of desired_dr_role inside __dwc3_set_mode while holding dwc->lock. Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly") Cc: stable <stable@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Sven Peter <sven@svenpeter.dev> Link: https://lore.kernel.org/r/20221128161526.79730-1-sven@svenpeter.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-12-14usb: dwc3: gadget: Disable GUSB2PHYCFG.SUSPHY for End TransferThinh Nguyen1-1/+2
[ Upstream commit 3aa07f72894d209fcf922ad686cbb28cf005aaad ] If there's a disconnection while operating in eSS, there may be a delay in VBUS drop response from the connector. In that case, the internal link state may drop to operate in usb2 speed while the controller thinks the VBUS is still high. The driver must make sure to disable GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed. The End Transfer command may be called, and only that command needs to go through at this point. Let's keep it simple and unconditionally disable GUSB2PHYCFG.SUSPHY whenever we issue the command. This scenario is not seen in real hardware. In a rare case, our prototype type-c controller/interface may have a slow response triggerring this issue. Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-12-02usb: dwc3: gadget: Clear ep descriptor lastThinh Nguyen1-6/+6
[ Upstream commit f90f5afd5083a7cb4aee13bd4cc0ae600bd381ca ] Until the endpoint is disabled, its descriptors should remain valid. When its requests are removed from ep disable, the request completion routine may attempt to access the endpoint's descriptor. Don't clear the descriptors before that. Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers") Cc: stable@vger.kernel.org Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/45db7c83b209259115bf652af210f8b2b3b1a383.1668561364.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-12-02usb: dwc3: gadget: Return -ESHUTDOWN on ep disableThinh Nguyen1-1/+1
[ Upstream commit ffb9da4a04c69567bad717707b6fdfbc4c216ef4 ] The usb_request API clearly noted that removed requests due to disabled endpoint should have -ESHUTDOWN status returned. Don't change this behavior. Fixes: b44c0e7fef51 ("usb: dwc3: gadget: conditionally remove requests") Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/3421859485cb32d77e2068549679a6c07a7797bc.1667875427.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: f90f5afd5083 ("usb: dwc3: gadget: Clear ep descriptor last") Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-12-02usb: dwc3: gadget: conditionally remove requestsMichael Grzeschik1-6/+6
[ Upstream commit b44c0e7fef51ee7e8ca8c6efbf706f5613787100 ] The functions stop_active_transfers and ep_disable are both calling remove_requests. This functions in both cases will giveback the requests with status ESHUTDOWN, which also represents an physical disconnection. For ep_disable this is not true. This patch adds the status parameter to remove_requests and sets the status to ECONNRESET on ep_disable. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Link: https://lore.kernel.org/r/20220720213523.1055897-1-m.grzeschik@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: f90f5afd5083 ("usb: dwc3: gadget: Clear ep descriptor last") Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-12-02usb: dwc3: exynos: Fix remove() functionMarek Szyprowski1-10/+1
commit e0481e5b3cc12ea7ccf4552d41518c89d3509004 upstream. The core DWC3 device node was not properly removed by the custom dwc3_exynos_remove_child() function. Replace it with generic of_platform_depopulate() which does that job right. Fixes: adcf20dcd262 ("usb: dwc3: exynos: Use of_platform API to create dwc3 core pdev") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Cc: stable@vger.kernel.org Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Link: https://lore.kernel.org/r/20221110154131.2577-1-m.szyprowski@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-11-25Revert "usb: dwc3: disable USB core PHY management"Johan Hovold1-10/+0
commit 5c294de36e7fb3e0cba0c4e1ef9a5f57bc080d0f upstream. This reverts commit 6000b8d900cd5f52fbcd0776d0cc396e88c8c2ea. The offending commit disabled the USB core PHY management as the dwc3 already manages the PHYs in question. Unfortunately some platforms have started relying on having USB core also controlling the PHY and this is specifically currently needed on some Exynos platforms for PHY calibration or connected device may fail to enumerate. The PHY calibration was previously handled in the dwc3 driver, but to work around some issues related to how the dwc3 driver interacts with xhci (e.g. using multiple drivers) this was moved to USB core by commits 34c7ed72f4f0 ("usb: core: phy: add support for PHY calibration") and a0a465569b45 ("usb: dwc3: remove generic PHY calibrate() calls"). The same PHY obviously should not be controlled from two different places, which for example do no agree on the PHY mode or power state during suspend, but as the offending patch was backported to stable, let's revert it for now. Reported-by: Stefan Agner <stefan@agner.ch> Link: https://lore.kernel.org/lkml/808bdba846bb60456adf10a3016911ee@agner.ch/ Fixes: 6000b8d900cd ("usb: dwc3: disable USB core PHY management") Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20221103144648.14197-1-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-11-03usb: dwc3: gadget: Don't set IMI for no_interruptThinh Nguyen1-2/+2
commit 308c316d16cbad99bb834767382baa693ac42169 upstream. The gadget driver may have a certain expectation of how the request completion flow should be from to its configuration. Make sure the controller driver respect that. That is, don't set IMI (Interrupt on Missed Isoc) when usb_request->no_interrupt is set. Also, the driver should only set IMI to the last TRB of a chain. Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Cc: stable@vger.kernel.org Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com> Tested-by: Jeff Vanhoof <jdv1029@gmail.com> Link: https://lore.kernel.org/r/ced336c84434571340c07994e3667a0ee284fefe.1666735451.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-11-03usb: dwc3: gadget: Stop processing more requests on IMIThinh Nguyen1-0/+4
commit f78961f8380b940e0cfc7e549336c21a2ad44f4d upstream. When servicing a transfer completion event, the dwc3 driver will reclaim TRBs of started requests up to the request associated with the interrupt event. Currently we don't check for interrupt due to missed isoc, and the driver may attempt to reclaim TRBs beyond the associated event. This causes invalid memory access when the hardware still owns the TRB. If there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure to stop servicing further. Note that only the last TRB of chained TRBs has its status updated with missed isoc. Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Cc: stable@vger.kernel.org Reported-by: Jeff Vanhoof <jdv1029@gmail.com> Reported-by: Dan Vacura <w36195@motorola.com> Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com> Tested-by: Jeff Vanhoof <jdv1029@gmail.com> Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-28usb: dwc3: gadget: Avoid duplicate requests to enable Run/StopWesley Cheng1-3/+5
[ Upstream commit 040f2dbd2010c43f33ad27249e6dac48456f4d99 ] Relocate the pullups_connected check until after it is ensured that there are no runtime PM transitions. If another context triggered the DWC3 core's runtime resume, it may have already enabled the Run/Stop. Do not re-run the entire pullup sequence again, as it may issue a core soft reset while Run/Stop is already set. This patch depends on commit 69e131d1ac4e ("usb: dwc3: gadget: Prevent repeat pullup()") Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded") Cc: stable <stable@kernel.org> Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com> Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-09-28usb: dwc3: gadget: Don't modify GEVNTCOUNT in pullup()Thinh Nguyen1-27/+8
[ Upstream commit 8f8034f493b5eb1ad21ff392fd30c0cf9e71f73f ] If the GEVNTCOUNT indicates events in the event buffer, the driver needs to acknowledge them before the controller can halt. Simply let the interrupt handler acknowledges the remaining event generated by the controller while polling for DSTS.DEVCTLHLT. This avoids disabling irq and taking care of race condition between the interrupt handlers and pullup(). Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/ea306ec93c41ccafbdb5d16404ff3b6eca299613.1650593829.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop") Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-09-28usb: dwc3: gadget: Refactor pullup()Thinh Nguyen1-29/+36
[ Upstream commit 861c010a2ee1bc4a66d23f0da4aa22e75d8eaa24 ] Move soft-disconnect sequence out of dwc3_gadget_pullup(). No functional change here. Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/4c0f259b17d95acaaa931f90276683a48a32fe22.1650593829.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop") Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-09-28usb: dwc3: gadget: Prevent repeat pullup()Thinh Nguyen1-0/+4
[ Upstream commit 69e131d1ac4e52a59ec181ab4f8aa8c48cd8fb64 ] Don't do soft-disconnect if it's previously done. Likewise, don't do soft-connect if the device is currently connected and running. It would break normal operation. Currently the caller of pullup() (udc's sysfs soft_connect) only checks if it had initiated disconnect to prevent repeating soft-disconnect. It doesn't check for soft-connect. To be safe, let's keep the check here regardless whether the udc core is fixed. Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/1c1345bd66c97a9d32f77d63aaadd04b7b037143.1650593829.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop") Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-09-28usb: dwc3: Issue core soft reset before enabling run/stopWesley Cheng3-3/+14
[ Upstream commit 0066472de157439d58454f4a55786f1045ea5681 ] It is recommended by the Synopsis databook to issue a DCTL.CSftReset when reconnecting from a device-initiated disconnect routine. This resolves issues with enumeration during fast composition switching cases, which result in an unknown device on the host. Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com> Link: https://lore.kernel.org/r/20220316011358.3057-1-quic_wcheng@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop") Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-09-28usb: dwc3: gadget: Avoid starting DWC3 gadget during UDC unbindWesley Cheng2-2/+4
[ Upstream commit 8217f07a50236779880f13e87f99224cd9117f83 ] There is a race present where the DWC3 runtime resume runs in parallel to the UDC unbind sequence. This will eventually lead to a possible scenario where we are enabling the run/stop bit, without a valid composition defined. Thread#1 (handling UDC unbind): usb_gadget_remove_driver() -->usb_gadget_disconnect() -->dwc3_gadget_pullup(0) --> continue UDC unbind sequence -->Thread#2 is running in parallel here Thread#2 (handing next cable connect) __dwc3_set_mode() -->pm_runtime_get_sync() -->dwc3_gadget_resume() -->dwc->gadget_driver is NOT NULL yet -->dwc3_gadget_run_stop(1) --> _dwc3gadget_start() ... Fix this by tracking the pullup disable routine, and avoiding resuming of the DWC3 gadget. Once the UDC is re-binded, that will trigger the pullup enable routine, which would handle enabling the DWC3 gadget. Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/20210917021852.2037-1-wcheng@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop") Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-09-08usb: dwc3: disable USB core PHY managementJohan Hovold1-0/+10
commit 6000b8d900cd5f52fbcd0776d0cc396e88c8c2ea upstream. The dwc3 driver manages its PHYs itself so the USB core PHY management needs to be disabled. Use the struct xhci_plat_priv hack added by commits 46034a999c07 ("usb: host: xhci-plat: add platform data support") and f768e718911e ("usb: host: xhci-plat: add priv quirk for skip PHY initialization") to propagate the setting for now. Fixes: 4e88d4c08301 ("usb: add a flag to skip PHY initialization to struct usb_hcd") Fixes: 178a0bce05cb ("usb: core: hcd: integrate the PHY wrapper into the HCD core") Tested-by: Matthias Kaehlcke <mka@chromium.org> Cc: stable <stable@kernel.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20220825131836.19769-1-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ johan: adjust context to 5.15 ] Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-08usb: dwc3: qcom: fix use-after-free on runtime-PM wakeupJohan Hovold2-1/+14
commit a872ab303d5ddd4c965f9cd868677781a33ce35a upstream. The Qualcomm dwc3 runtime-PM implementation checks the xhci platform-device pointer in the wakeup-interrupt handler to determine whether the controller is in host mode and if so triggers a resume. After a role switch in OTG mode the xhci platform-device would have been freed and the next wakeup from runtime suspend would access the freed memory. Note that role switching is executed from a freezable workqueue, which guarantees that the pointer is stable during suspend. Also note that runtime PM has been broken since commit 2664deb09306 ("usb: dwc3: qcom: Honor wakeup enabled/disabled state"), which incidentally also prevents this issue from being triggered. Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver") Cc: stable@vger.kernel.org # 4.18 Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20220804151001.23612-5-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ johan: adjust context for 5.15 ] Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-08usb: dwc3: fix PHY disable sequenceJohan Hovold1-9/+10
commit d2ac7bef95c9ead307801ccb6cb6dfbeb14247bf upstream. Generic PHYs must be powered-off before they can be tore down. Similarly, suspending legacy PHYs after having powered them off makes no sense. Fix the dwc3_core_exit() (e.g. called during suspend) and open-coded dwc3_probe() error-path sequences that got this wrong. Note that this makes dwc3_core_exit() match the dwc3_core_init() error path with respect to powering off the PHYs. Fixes: 03c1fd622f72 ("usb: dwc3: core: add phy cleanup for probe error handling") Fixes: c499ff71ff2a ("usb: dwc3: core: re-factor init and exit paths") Cc: stable@vger.kernel.org # 4.8 Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20220804151001.23612-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ johan: adjust context to 5.15 ] Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-18 07:05:39 +0300