| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 6d735722063a945de56472bdc6bfcb170fd43b86 upstream.
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe82 ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ddaa6a274578e23745b7466346fc2650df8f959 upstream.
If dwc3 is runtime suspended we defer processing the event buffer
until resume, by setting the pending_events flag. Set this flag before
triggering resume to avoid race with the runtime resume callback.
While handling the pending events, in addition to checking the event
buffer we also need to process it. Handle this by explicitly calling
dwc3_thread_interrupt(). Also balance the runtime pm get() operation
that triggered this processing.
Cc: stable@vger.kernel.org
Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM")
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230801192658.19275-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c0aabed9cabe057309779a9e26fe86a113d24dad upstream.
In scenarios where pullup relies on resume (get sync) to initialize
the controller and set the run stop bit, then core_init is followed by
gadget_resume which will eventually set run stop bit.
But in cases where the core_init fails, the return value is not sent
back to udc appropriately. So according to UDC the controller has
started but in reality we never set the run stop bit.
On systems like Android, there are uevents sent to HAL depending on
whether the configfs_bind / configfs_disconnect were invoked. In the
above mentioned scnenario, if the core init fails, the run stop won't
be set and the cable plug-out won't result in generation of any
disconnect event and userspace would never get any uevent regarding
cable plug out and we never call pullup(0) again. Furthermore none of
the next Plug-In/Plug-Out's would be known to configfs.
Return back the appropriate result to UDC to let the userspace/
configfs know that the pullup failed so they can take appropriate
action.
Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <20230618120949.14868-1-quic_kriskura@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00f8205ffcf112dcef14f8151d78075d38d22c08 upstream.
Consider a scenario where cable disconnect happens when there is an active
usb reqest queued to the UDC. As part of the disconnect we would issue an
end transfer with no interrupt-on-completion before giving back this
request. Since we are giving back the request without skipping TRBs the
num_trbs field of dwc3_request still holds the stale value previously used.
Function drivers re-use same request for a given bind-unbind session and
hence their dwc3_request context gets preserved across cable
disconnect/connect. When such a request gets re-queued after cable connect,
we would increase the num_trbs field on top of the previous stale value
thus incorrectly representing the number of TRBs used. Fix this by
resetting num_trbs field before giving back the request.
Fixes: 09fe1f8d7e2f ("usb: dwc3: gadget: track number of TRBs per request")
Cc: stable <stable@kernel.org>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <1685654850-8468-1-git-send-email-quic_eserrao@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4decf4060ecfee1f7a710999fcd421645ac0c419 ]
Currently we process the suspend interrupt event only if the
device is in configured state. Consider a case where device
is not configured and got suspend interrupt, in that case our
gadget will still use 100mA as composite_suspend didn't happen.
But battery charging specification (BC1.2) expects a downstream
device to draw less than 2.5mA when unconnected OR suspended.
Fix this by removing the condition for processing suspend event,
and thus composite_resume would set vbus draw to 2.
Fixes: 72704f876f50 ("dwc3: gadget: Implement the suspend entry event handler")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677217619-10261-2-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8a2bb4eb75866275b5cf7de2e593ac3449643e2 ]
Previously, there was a 100uS delay inserted after issuing an end transfer
command for specific controller revisions. This was due to the fact that
there was a GUCTL2 bit field which enabled synchronous completion of the
end transfer command once the CMDACT bit was cleared in the DEPCMD
register. Since this bit does not exist for all controller revisions and
the current implementation heavily relies on utizling the EndTransfer
command completion interrupt, add the delay back in for uses where the
interrupt on completion bit is not set, and increase the duration to 1ms
for the controller to complete the command.
An issue was seen where the USB request buffer was unmapped while the DWC3
controller was still accessing the TRB. However, it was confirmed that the
end transfer command was successfully submitted. (no end transfer timeout)
In situations, such as dwc3_gadget_soft_disconnect() and
__dwc3_gadget_ep_disable(), the dwc3_remove_request() is utilized, which
will issue the end transfer command, and follow up with
dwc3_gadget_giveback(). At least for the USB ep disable path, it is
required for any pending and started requests to be completed and returned
to the function driver in the same context of the disable call. Without
the GUCTL2 bit, it is not ensured that the end transfer is completed before
the buffers are unmapped.
Fixes: cf2f8b63f7f1 ("usb: dwc3: gadget: Remove END_TRANSFER delay")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230306200557.29387-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e192cc7b52399d1b073f88cd3ba128b74d3a57f1 ]
This patch adds the extra function __dwc3_stop_active_transfer to
consolidate the same codepath.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220306211251.2281335-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: d8a2bb4eb758 ("usb: dwc3: gadget: Add 1ms delay after end transfer command without IOC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3aa07f72894d209fcf922ad686cbb28cf005aaad ]
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f90f5afd5083a7cb4aee13bd4cc0ae600bd381ca ]
Until the endpoint is disabled, its descriptors should remain valid.
When its requests are removed from ep disable, the request completion
routine may attempt to access the endpoint's descriptor. Don't clear the
descriptors before that.
Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/45db7c83b209259115bf652af210f8b2b3b1a383.1668561364.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ffb9da4a04c69567bad717707b6fdfbc4c216ef4 ]
The usb_request API clearly noted that removed requests due to disabled
endpoint should have -ESHUTDOWN status returned. Don't change this
behavior.
Fixes: b44c0e7fef51 ("usb: dwc3: gadget: conditionally remove requests")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3421859485cb32d77e2068549679a6c07a7797bc.1667875427.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f90f5afd5083 ("usb: dwc3: gadget: Clear ep descriptor last")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b44c0e7fef51ee7e8ca8c6efbf706f5613787100 ]
The functions stop_active_transfers and ep_disable are both calling
remove_requests. This functions in both cases will giveback the requests
with status ESHUTDOWN, which also represents an physical disconnection.
For ep_disable this is not true. This patch adds the status parameter to
remove_requests and sets the status to ECONNRESET on ep_disable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720213523.1055897-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f90f5afd5083 ("usb: dwc3: gadget: Clear ep descriptor last")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 308c316d16cbad99bb834767382baa693ac42169 upstream.
The gadget driver may have a certain expectation of how the request
completion flow should be from to its configuration. Make sure the
controller driver respect that. That is, don't set IMI (Interrupt on
Missed Isoc) when usb_request->no_interrupt is set. Also, the driver
should only set IMI to the last TRB of a chain.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/ced336c84434571340c07994e3667a0ee284fefe.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f78961f8380b940e0cfc7e549336c21a2ad44f4d upstream.
When servicing a transfer completion event, the dwc3 driver will reclaim
TRBs of started requests up to the request associated with the interrupt
event. Currently we don't check for interrupt due to missed isoc, and
the driver may attempt to reclaim TRBs beyond the associated event. This
causes invalid memory access when the hardware still owns the TRB. If
there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure
to stop servicing further.
Note that only the last TRB of chained TRBs has its status updated with
missed isoc.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Reported-by: Jeff Vanhoof <jdv1029@gmail.com>
Reported-by: Dan Vacura <w36195@motorola.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 040f2dbd2010c43f33ad27249e6dac48456f4d99 ]
Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions. If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop. Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.
This patch depends on
commit 69e131d1ac4e ("usb: dwc3: gadget: Prevent repeat pullup()")
Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8f8034f493b5eb1ad21ff392fd30c0cf9e71f73f ]
If the GEVNTCOUNT indicates events in the event buffer, the driver needs
to acknowledge them before the controller can halt. Simply let the
interrupt handler acknowledges the remaining event generated by the
controller while polling for DSTS.DEVCTLHLT. This avoids disabling irq
and taking care of race condition between the interrupt handlers and
pullup().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ea306ec93c41ccafbdb5d16404ff3b6eca299613.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 861c010a2ee1bc4a66d23f0da4aa22e75d8eaa24 ]
Move soft-disconnect sequence out of dwc3_gadget_pullup(). No
functional change here.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/4c0f259b17d95acaaa931f90276683a48a32fe22.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 69e131d1ac4e52a59ec181ab4f8aa8c48cd8fb64 ]
Don't do soft-disconnect if it's previously done. Likewise, don't do
soft-connect if the device is currently connected and running. It would
break normal operation.
Currently the caller of pullup() (udc's sysfs soft_connect) only checks
if it had initiated disconnect to prevent repeating soft-disconnect. It
doesn't check for soft-connect. To be safe, let's keep the check here
regardless whether the udc core is fixed.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1c1345bd66c97a9d32f77d63aaadd04b7b037143.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0066472de157439d58454f4a55786f1045ea5681 ]
It is recommended by the Synopsis databook to issue a DCTL.CSftReset
when reconnecting from a device-initiated disconnect routine. This
resolves issues with enumeration during fast composition switching
cases, which result in an unknown device on the host.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220316011358.3057-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8217f07a50236779880f13e87f99224cd9117f83 ]
There is a race present where the DWC3 runtime resume runs in parallel
to the UDC unbind sequence. This will eventually lead to a possible
scenario where we are enabling the run/stop bit, without a valid
composition defined.
Thread#1 (handling UDC unbind):
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
--> continue UDC unbind sequence
-->Thread#2 is running in parallel here
Thread#2 (handing next cable connect)
__dwc3_set_mode()
-->pm_runtime_get_sync()
-->dwc3_gadget_resume()
-->dwc->gadget_driver is NOT NULL yet
-->dwc3_gadget_run_stop(1)
--> _dwc3gadget_start()
...
Fix this by tracking the pullup disable routine, and avoiding resuming
of the DWC3 gadget. Once the UDC is re-binded, that will trigger the
pullup enable routine, which would handle enabling the DWC3 gadget.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210917021852.2037-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8affe37c525d800a2628c4ecfaed13b77dc5634a upstream.
For High-Speed Transfers the prepare_one_trb function is calculating the
multiplier setting for the trb based on the length parameter of the trb
currently prepared. This assumption is wrong. For trbs with a sg list,
the length of the actual request has to be taken instead.
Fixes: 40d829fb2ec6 ("usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220704141812.1532306-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 23385cec5f354794dadced7f28c31da7ae3eb54c upstream.
The function __dwc3_prepare_one_trb has many parameters. Since it is
only used in dwc3_prepare_one_trb there is no point in keeping the
function. We merge both functions and get rid of the big list of
parameters.
Fixes: 40d829fb2ec6 ("usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220704141812.1532306-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7441b273388b9a59d8387a03ffbbca9d5af6348c upstream.
The DWC3_EVENT_PENDING flag is used to protect against invalid call to
top-half interrupt handler, which can occur when there's a delay in
software detection of the interrupt line deassertion.
However, the clearing of this flag was done prior to unmasking the
interrupt line, creating opportunity where the top-half handler can
come. This breaks the serialization and creates a race between the
top-half and bottom-half handler, resulting in losing synchronization
between the controller and the driver when processing events.
To fix this, make sure the clearing of the DWC3_EVENT_PENDING is done at
the end of the bottom-half handler.
Fixes: d325a1de49d6 ("usb: dwc3: gadget: Prevent losing events in event cache")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/8670aaf1cf52e7d1e6df2a827af2d77263b93b75.1656380429.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c5880745b4439ac64eccdb040e37fc1cc4c5406 upstream.
When dwc3_gadget_ep_cleanup_completed_requests() called to
dwc3_gadget_giveback() where the dwc3 lock is released, other thread is
able to execute. In this situation, usb_ep_disable() gets the chance to
clear endpoint descriptor pointer which leds to the null pointer
dereference problem. So needs to move the null pointer check to a proper
place.
Example call stack:
Thread#1:
dwc3_thread_interrupt()
spin_lock
-> dwc3_process_event_buf()
-> dwc3_process_event_entry()
-> dwc3_endpoint_interrupt()
-> dwc3_gadget_endpoint_trbs_complete()
-> dwc3_gadget_ep_cleanup_completed_requests()
...
-> dwc3_giveback()
spin_unlock
Thread#2 executes
Thread#2:
configfs_composite_disconnect()
-> __composite_disconnect()
-> ffs_func_disable()
-> ffs_func_set_alt()
-> ffs_func_eps_disable()
-> usb_ep_disable()
wait for dwc3 spin_lock
Thread#1 released lock
clear endpoint.desc
Fixes: 26288448120b ("usb: dwc3: gadget: Fix null pointer exception")
Cc: stable <stable@kernel.org>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20220518061315.3359198-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c7428dbddcf4ea1919e1c8e15f715b94ca359268 upstream.
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Fixes: 6d8a019614f3 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84918a89d6efaff075de570b55642b6f4ceeac6d upstream.
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e7b0 ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 117b4e96c7f362eb6459543883fc07f77662472c upstream.
With CPU re-ordering on write instructions, there might
be a chance that the HWO is set before the TRB is updated
with the new mapped buffer address.
And in the case where core is processing a list of TRBs
it is possible that it fetched the TRBs when the HWO is set
but before the buffer address is updated.
Prevent this by adding a memory barrier before the HWO
is updated to ensure that the core always process the
updated TRBs.
Fixes: f6bafc6a1c9d ("usb: dwc3: convert TRBs into bitshifts")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1644207958-18287-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26288448120b28af1dfd85a6fa6b6d55a16c7f2f upstream.
In the endpoint interrupt functions
dwc3_gadget_endpoint_transfer_in_progress() and
dwc3_gadget_endpoint_trbs_complete() will dereference the endpoint
descriptor. But it could be cleared in __dwc3_gadget_ep_disable()
when accessory disconnected. So we need to check whether it is null
or not before dereferencing it.
Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20211109092642.3507692-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63c4c320ccf77074ffe9019ac596603133c1b517 upstream.
The programming guide noted that the driver needs to verify if the link
state is in U0 before executing the Start Transfer command. If it's not
in U0, the driver needs to perform remote wakeup. This is not accurate.
If the link state is in U1/U2, then the controller will not respond to
link recovery request from DCTL.ULSTCHNGREQ. The Start Transfer command
will trigger a link recovery if it is in U1/U2. A clarification will be
added to the programming guide for all controller versions.
The current implementation shouldn't cause any functional issue. It may
occasionally report an invalid time out warning from failed link
recovery request. The driver will still go ahead with the Start Transfer
command if the remote wakeup fails. The new change only initiates remote
wakeup where it is needed, which is when the link state is in L1/L2/U3.
Fixes: c36d8e947a56 ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/05b4a5fbfbd0863fc9b1d7af934a366219e3d0b4.1635204761.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d74dc3e9f58c28689cef1faccf918e06587367d3 upstream.
The End Transfer command from a stream endpoint will generate a NoStream
event, and we should ignore it. Currently we set the flag
DWC3_EP_IGNORE_NEXT_NOSTREAM to track this prior to sending the command,
and it will be cleared on the next stream event. However, a stream event
may be generated before the End Transfer command completion and
prematurely clear the flag. Fix this by setting the flag on End Transfer
completion instead.
Fixes: 140ca4cfea8a ("usb: dwc3: gadget: Handle stream transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cee1253af4c3600edb878d11c9c08b040817ae23.1635203975.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4a1e25c0a029b97ea4a3d423a6392bfacc3b2e39 upstream.
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb0147364850 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so")
Cc: <stable@vger.kernel.org>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 51f1954ad853d01ba4dc2b35dee14d8490ee05a1 upstream.
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
Fixes: c4233573f6ee ("usb: dwc3: gadget: prepare TRBs on update transfers too")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e91e975affb0d0d02770686afc3a5b9eb84409f6.1629335416.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb10f68ad8150f243964b19391711aaac5e8ff42 upstream.
If the device is already in the runtime suspended state, any call to
the pullup routine will issue a runtime resume on the DWC3 core
device. If the USB gadget is disabling the pullup, then avoid having
to issue a runtime resume, as DWC3 gadget has already been
halted/stopped.
This fixes an issue where the following condition occurs:
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
-->pm_runtime_get_sync() -> ret = 0
-->pm_runtime_put() [async]
-->usb_gadget_udc_stop()
-->dwc3_gadget_stop()
-->dwc->gadget_driver = NULL
...
dwc3_suspend_common()
-->dwc3_gadget_suspend()
-->DWC3 halt/stop routine skipped, driver_data == NULL
This leads to a situation where the DWC3 gadget is not properly
stopped, as the runtime resume would have re-enabled EP0 and event
interrupts, and since we avoided the DWC3 gadget suspend, these
resources were never disabled.
Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1628058245-30692-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d396bb0a5b62b326f6be7594d8bd46b088296bd upstream.
The DWC3 DebugFS directory and files are currently created once
during probe. This includes creation of subdirectories for each
of the gadget's endpoints. This works fine for peripheral-only
controllers, as dwc3_core_init_mode() calls dwc3_gadget_init()
just prior to calling dwc3_debugfs_init().
However, for dual-role controllers, dwc3_core_init_mode() will
instead call dwc3_drd_init() which is problematic in a few ways.
First, the initial state must be determined, then dwc3_set_mode()
will have to schedule drd_work and by then dwc3_debugfs_init()
could have already been invoked. Even if the initial mode is
peripheral, dwc3_gadget_init() happens after the DebugFS files
are created, and worse so if the initial state is host and the
controller switches to peripheral much later. And secondly,
even if the gadget endpoints' debug entries were successfully
created, if the controller exits peripheral mode, its dwc3_eps
are freed so the debug files would now hold stale references.
So it is best if the DebugFS endpoint entries are created and
removed dynamically at the same time the underlying dwc3_eps are.
Do this by calling dwc3_debugfs_create_endpoint_dir() as each
endpoint is created, and conversely remove the DebugFS entry when
the endpoint is freed.
Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210529192932.22912-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8212937305f84ef73ea81036dafb80c557583d4b upstream.
Current sequence utilizes dwc3_gadget_disable_irq() alongside
synchronize_irq() to ensure that no further DWC3 events are generated.
However, the dwc3_gadget_disable_irq() API only disables device
specific events. Endpoint events can still be generated. Briefly
disable the interrupt line, so that the cleanup code can run to
prevent device and endpoint events. (i.e. __dwc3_gadget_stop() and
dwc3_stop_active_transfers() respectively)
Without doing so, it can lead to both the interrupt handler and the
pullup disable routine both writing to the GEVNTCOUNT register, which
will cause an incorrect count being read from future interrupts.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1621571037-1424-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03715ea2e3dbbc56947137ce3b4ac18a726b2f87 upstream.
There exists a possible scenario in which dwc3_gadget_init() can fail:
during during host -> peripheral mode switch in dwc3_set_mode(), and
a pending gadget driver fails to bind. Then, if the DRD undergoes
another mode switch from peripheral->host the resulting
dwc3_gadget_exit() will attempt to reference an invalid and dangling
dwc->gadget pointer as well as call dma_free_coherent() on unmapped
DMA pointers.
The exact scenario can be reproduced as follows:
- Start DWC3 in peripheral mode
- Configure ConfigFS gadget with FunctionFS instance (or use g_ffs)
- Run FunctionFS userspace application (open EPs, write descriptors, etc)
- Bind gadget driver to DWC3's UDC
- Switch DWC3 to host mode
=> dwc3_gadget_exit() is called. usb_del_gadget() will put the
ConfigFS driver instance on the gadget_driver_pending_list
- Stop FunctionFS application (closes the ep files)
- Switch DWC3 to peripheral mode
=> dwc3_gadget_init() fails as usb_add_gadget() calls
check_pending_gadget_drivers() and attempts to rebind the UDC
to the ConfigFS gadget but fails with -19 (-ENODEV) because the
FFS instance is not in FFS_ACTIVE state (userspace has not
re-opened and written the descriptors yet, i.e. desc_ready!=0).
- Switch DWC3 back to host mode
=> dwc3_gadget_exit() is called again, but this time dwc->gadget
is invalid.
Although it can be argued that userspace should take responsibility
for ensuring that the FunctionFS application be ready prior to
allowing the composite driver bind to the UDC, failure to do so
should not result in a panic from the kernel driver.
Fix this by setting dwc->gadget to NULL in the failure path of
dwc3_gadget_init() and add a check to dwc3_gadget_exit() to bail out
unless the gadget pointer is valid.
Fixes: e81a7018d93a ("usb: dwc3: allocate gadget structure dynamically")
Cc: <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210528160405.17550-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25dda9fc56bd90d45f9a4516bcfa5211e61b4290 upstream.
The driver incorrectly uses req->num_pending_sgs to track both the
number of pending and queued SG entries. It only prepares the next
request if the previous is done, and it doesn't update num_pending_sgs
until there is TRB completion interrupt. This may starve the controller
of more TRBs until the num_pending_sgs is decremented.
Fix this by decrementing the num_pending_sgs after they are queued and
properly track both num_mapped_sgs and num_queued_sgs.
Fixes: c96e6725db9d ("usb: dwc3: gadget: Correct the logic for queuing sgs")
Cc: <stable@vger.kernel.org>
Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ba24591dbcaad8f244a3e88bd449bb7205a5aec3.1620874069.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18ffa988dbae69cc6e9949cddd9606f6fe533894 upstream.
If an error is received when issuing a start or update transfer
command, the error handler will stop all active requests (including
the current USB request), and call dwc3_gadget_giveback() to notify
function drivers of the requests which have been stopped. Avoid
returning an error for kick transfer during EP queue, to remove
duplicate cleanup operations on the request being queued.
Fixes: 8d99087c2db8 ("usb: dwc3: gadget: Properly handle failed kick_transfer")
cc: stable@vger.kernel.org
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1620410119-24971-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1d90dd27254c44d087ad3f8b5b3e4fff0571f45 upstream.
commit 72704f876f50 ("dwc3: gadget: Implement the suspend entry event
handler") introduced (nearly 5 years ago!) an interrupt handler for
U3/L1-L2 suspend events. The problem is that these events aren't
currently enabled in the DEVTEN register so the handler is never
even invoked. Fix this simply by enabling the corresponding bit
in dwc3_gadget_enable_irq() using the same revision check as found
in the handler.
Fixes: 72704f876f50 ("dwc3: gadget: Implement the suspend entry event handler")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210428090111.3370-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bb9c74a5bd1462499fe5ccb1e3c5ac40dcfa9139 ]
As part of commit e81a7018d93a ("usb: dwc3: allocate gadget structure
dynamically") the dwc3_gadget_release() was added which will free
the dwc->gadget structure upon the device's removal when
usb_del_gadget_udc() is called in dwc3_gadget_exit().
However, simply freeing the gadget results a dangling pointer
situation: the endpoints created in dwc3_gadget_init_endpoints()
have their dep->endpoint.ep_list members chained off the list_head
anchored at dwc->gadget->ep_list. Thus when dwc->gadget is freed,
the first dwc3_ep in the list now has a dangling prev pointer and
likewise for the next pointer of the dwc3_ep at the tail of the list.
The dwc3_gadget_free_endpoints() that follows will result in a
use-after-free when it calls list_del().
This was caught by enabling KASAN and performing a driver unbind.
The recent commit 568262bf5492 ("usb: dwc3: core: Add shutdown
callback for dwc3") also exposes this as a panic during shutdown.
There are a few possibilities to fix this. One could be to perform
a list_del() of the gadget->ep_list itself which removes it from
the rest of the dwc3_ep chain.
Another approach is what this patch does, by splitting up the
usb_del_gadget_udc() call into its separate "del" and "put"
components. This allows dwc3_gadget_free_endpoints() to be
called before the gadget is finally freed with usb_put_gadget().
Fixes: e81a7018d93a ("usb: dwc3: allocate gadget structure dynamically")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210501093558.7375-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c560e76319a94a3b9285bc426c609903408e4826 upstream.
The START_TRANSFER command needs to be executed while in ON/U0 link
state (with an exception during register initialization). Don't use
dwc->link_state to check this since the driver only tracks the link
state when the link state change interrupt is enabled. Check the link
state from DSTS register instead.
Note that often the host already brings the device out of low power
before it sends/requests the next transfer. So, the user won't see any
issue when the device starts transfer then. This issue is more
noticeable in cases when the device delays starting transfer, which can
happen during delayed control status after the host put the device in
low power.
Fixes: 799e9dc82968 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/bcefaa9ecbc3e1936858c0baa14de6612960e909.1618884221.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3232a3ce55edfc0d7f8904543b4088a5339c2b2b upstream.
The programming guide incorrectly stated that the DCFG.bInterval_m1 must
be set to 0 when operating in fullspeed. There's no such limitation for
all IPs. See DWC_usb3x programming guide section 3.2.2.1.
Fixes: a1679af85b2a ("usb: dwc3: gadget: Fix setting of DEPCFG.bInterval_m1")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5d4139ae89d810eb0a2d8577fb096fc88e87bfab.1618472454.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 475e8be53d0496f9bc6159f4abb3ff5f9b90e8de ]
If the device doesn't support LPM, make sure to disable the LPM
capability and don't advertise to the host that it supports it.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9e68527ff932b1646f92a7593d4092a903754666.1618366071.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 71ca43f30df9c642970f9dc9b2d6f463f4967e7b ]
The current dwc3_gadget_reset_interrupt() will stop any active
transfers, but only addresses blocking of EP queuing for while we are
coming from a disconnected scenario, i.e. after receiving the disconnect
event. If the host decides to issue a bus reset on the device, the
connected parameter will still be set to true, allowing for EP queuing
to continue while we are disabling the functions. To avoid this, set the
connected flag to false until the stop active transfers is complete.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616146285-19149-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5aef629704ad4d983ecf5c8a25840f16e45b6d59 upstream.
Ensure that dep->flags are cleared until after stop active transfers
is completed. Otherwise, the ENDXFER command will not be executed
during ep disable.
Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616610664-16495-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f09ddcfcb8c569675066337adac2ac205113471f upstream.
In the situations where the DWC3 gadget stops active transfers, once
calling the dwc3_gadget_giveback(), there is a chance where a function
driver can queue a new USB request in between the time where the dwc3
lock has been released and re-aquired. This occurs after we've already
issued an ENDXFER command. When the stop active transfers continues
to remove USB requests from all dep lists, the newly added request will
also be removed, while controller still has an active TRB for it.
This can lead to the controller accessing an unmapped memory address.
Fix this by ensuring parameters to prevent EP queuing are set before
calling the stop active transfers API.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1615507142-23097-1-git-send-email-wcheng@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 77adb8bdf4227257e26b7ff67272678e66a0b250 upstream.
The DWC3 runtime suspend routine checks for the USB connected parameter to
determine if the controller can enter into a low power state. The
connected state is only set to false after receiving a disconnect event.
However, in the case of a device initiated disconnect (i.e. UDC unbind),
the controller is halted and a disconnect event is never generated. Set
the connected flag to false if issuing a device initiated disconnect to
allow the controller to be suspended.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609283136-22140-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b049f55ed95cd889bcdb3034fd75e1f01852b38 upstream.
The dep->interval captures the number of frames/microframes per interval
from bInterval. Fullspeed interrupt endpoint bInterval is the number of
frames per interval and not 2^(bInterval - 1). So fix it here. This
change is only for debugging purpose and should not affect the interrupt
endpoint operation.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1263b563dedc4ab8b0fb854fba06ce4bc56bd495.1612820995.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1679af85b2ae35a2b78ad04c18bb069c37330cc upstream.
Valid range for DEPCFG.bInterval_m1 is from 0 to 13, and it must be set
to 0 when the controller operates in full-speed. See the programming
guide for DEPCFG command section 3.2.2.1 (v3.30a).
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3f57026f993c0ce71498dbb06e49b3a47c4d0265.1612820995.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5c7682aaaa10e42928d73de1c9e1e02d2b14c2e upstream.
If an active transfer is dequeued, then the endpoint is freed to start a
new transfer. Make sure to clear the endpoint's transfer wait flag for
this case.
Fixes: e0d19563eb6c ("usb: dwc3: gadget: Wait for transfer completion")
Cc: stable@vger.kernel.org
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b81cd5b5281cfbfdadb002c4bcf5c9be7c017cfd.1609828485.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1383b3537a7bea1c213baa7878ccc4ecf4413b5 upstream.
usb_gadget_deactivate/usb_gadget_activate does not execute the UDC start
operation, which may leave EP0 disabled and event IRQs disabled when
re-activating the function. Move the enabling/disabling of USB EP0 and
device event IRQs to be performed in the pullup routine.
Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller")
Tested-by: Michael Tretter <m.tretter@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reported-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609282837-21666-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
