summaryrefslogtreecommitdiff
path: root/drivers/usb/dwc2/params.c
AgeCommit message (Collapse)AuthorFilesLines
2018-03-23Merge tag 'usb-for-v4.17' of ↵Greg Kroah-Hartman1-18/+73
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing Felipe writes: usb: changes for v4.17 merge window Quite a lot happened in this cycle, with a total of 95 non-merge commits. The most interesting parts are listed below: Synopsys has been adding better support for USB 3.1 to dwc3. The same series also sets g_mass_storage's max speed to SSP. Roger Quadros (TI) added support for dual-role using the OTG block available in some dwc3 implementations, this makes sure that AM437x can swap roles in runtime. We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to the work of Martin Blumenstingl. We also have a ton of changes in dwc2 (51% of all changes, in fact). The most interesting part there is the support for Hibernation (a Synopsys PM feature). Apart from these, we have our regular set of non-critical fixes all over the place.
2018-03-13usb: dwc2: Force mode optimizationsVardan Mikayelyan1-10/+2
If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during driver probe to get the host and device specific HW parameters. Then we clear the force mode bits so that the core operates in OTG mode. The force mode bits should not be touched at any other time during the driver lifetime and they should be preserved whenever the GUSBCFG register is written to. The force mode bit values will persist across soft resets of the core. If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the force mode is set just once at probe to configure the core as either a host or peripheral. Given the above, we no longer need any other reset delays, force delays, or any forced modes anywhere else in the driver. So replace all calls to dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove all other unnecessary delays. Also remove the dwc2_force_mode_if_needed() function since the "if needed" part is already taken care of by the polling in dwc2_force_mode(). Finally, remove all other calls to dwc2_clear_force_mode(). Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc2: Enable power downJohn Youn1-1/+15
Enable the power down option based on the core capability. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: Artur Petrosyan <arturp@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc2: Add hibernation field into dwc2_hw_paramsVardan Mikayelyan1-0/+34
Add parameter and it's initialization, needed for hibernation. Reimplement dwc2_set_param_power_down() to support hibernation too. Now 'power_down' parameter can be initialized with 0, 1 or 2. 0 - No 1 - Partial power down 2 - Hibernation Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc2: Rename hibernation to partial_power_downVardan Mikayelyan1-1/+1
No-op change, only rename. This code was misnamed originally. It was only responsible for partial power down and not for hibernation. Rename core_params->hibernation to core_params->power_down, dwc2_set_param_hibernation() to dwc2_set_param_power_down(). Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc2: Add core parameters for LPM supportSevak Arakelyan1-0/+13
Add lpm, lpm_clock_gating, besl, hird_threshold_en and hird_threshold core parameters. These will indicate LPM and LPM Errata support as well as chosen L1 sleeping mode for the core and PHY. Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc2: Add ACG support to the driverRazmik Karapetyan1-0/+3
Added function for supporting Active Clock Gating functionality in the driver. PCGCCTL1 (Power and Clock Control) register will be used for controlling the core`s active clock gating feature, and the previously reserved 12th bit in GHWCFG4 now indicates that the controller supports the Dynamic Power Reduction (Active Clock Gating) during no traffic scenarios such as L0, idle, resume and suspend states. dwc2_enable_acg() function sets GATEEN bit in PCGCCTL1 register and enables ACG, if it supported. According to ACG functional specification, enabling of ACG feature in host mode done in host initialization, before turning Vbus on, specifically in dwc2_core_host_init function. Enabling of ACG feature in device mode done in device initialization, before clearing the SftDiscon bit in DCTL. This bit was cleared in dwc2_hsotg_core_connect() function.So dwc2_enable_acg() called before dwc2_core_connect() calls. Signed-off-by: Razmik Karapetyan <razmik@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc2: Set AHB burst size to INCRRazmik Karapetyan1-1/+1
Changed AHB burst size from INCR4 to INCR by default. With this value driver shows excellent DMA performance. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Razmik Karapetyan <razmik@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc2: Remove version check in GSNPSIDGevorg Sahakyan1-6/+5
Only check the ID portion of the GSNPSID register and don’t check the version. This will allow the driver to work with version 4.00a and later of the DWC_hsotg IP. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com> Signed-off-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-05usb: dwc2: fix STM32F7 USB OTG HS compatibleAmelie Delaunay1-3/+3
This patch fixes compatible for STM32F7 USB OTG HS and consistently rename dw2_set_params function. The v2 former patch [1] had been acked by Paul Young, but v1 was merged. [1] https://patchwork.kernel.org/patch/9925573/ Fixes: d8fae8b93682 ("usb: dwc2: add support for STM32F7xx USB OTG HS") Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11usb: dwc2: Fix TxFIFOn sizes and total TxFIFO size issuesMinas Harutyunyan1-10/+19
In host mode reading from DPTXSIZn returning invalid value in dwc2_check_param_tx_fifo_sizes function. In total TxFIFO size calculations unnecessarily reducing by ep_info. hw->total_fifo_size can be fully allocated for FIFO's. Added num_dev_in_eps member in dwc2_hw_params structure to save number of IN EPs. Added g_tx_fifo_size array in dwc2_hw_params structure to store power on reset values of DPTXSIZn registers in forced device mode. Updated dwc2_hsotg_tx_fifo_count() function to get TxFIFO count from num_dev_in_eps. Updated dwc2_get_dev_hwparams() function to store DPTXFSIZn in g_tx_fifo_size array. dwc2_get_host/dev_hwparams() functions call moved after num_dev_in_eps set from hwcfg4. Modified dwc2_check_param_tx_fifo_sizes() function to check TxFIFOn sizes based on g_tx_fifo_size array. Removed ep_info subtraction during calculation of tx_addr_max in dwc2_hsotg_tx_fifo_total_depth() function. Also removed dwc2_hsotg_ep_info_size() function as no more need. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com> Signed-off-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-11-04USB: add SPDX identifiers to all remaining files in drivers/usb/Greg Kroah-Hartman1-0/+1
It's good to have SPDX identifiers in all files to make it easier to audit the kernel tree for correct licenses. Update the drivers/usb/ and include/linux/usb* files with the correct SPDX license identifier based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This work is based on a script and data from Thomas Gleixner, Philippe Ombredanne, and Kate Stewart. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-19usb: dwc2: disable erroneous overcurrent conditionDinh Nguyen1-0/+3
For the case where an external VBUS is used, we should enable the external VBUS comparator in the driver. This would prevent an unnecessary overcurrent error which would then disable the host port. This patch uses the standard 'disable-over-current' binding to allow of the option of disabling the over-current condition. Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-19usb: dwc2: add support for STM32F7xx USB OTG HSAmelie Delaunay1-0/+11
This patch adds the dwc2_set_params function for STM32F7xx USB OTG HS. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-02usb: dwc2: add support for the DWC2 controller on Meson8 SoCsMartin Blumenstingl1-0/+2
USB support in the Meson8 SoCs is provided by a DWC2 controller which works with the same settings as Meson8b and GXBB. Using the generic "snps,dwc2" binding results in an endless stream of "Overcurrent change detected" messages. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11usb: dwc2: Add support for STM32F429/439/469 USB OTG HS/FS in FS mode ↵Bruno Herrera1-0/+19
(internal PHY) This patch introduces a new parameter to activate USB OTG HS/FS core embedded phy transceiver. The STM32F4x9 SoC uses the GGPIO register to enable the transceiver. Also add the dwc2_set_params function for stm32f4 otg fs. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Bruno Herrera <bruherrera@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: gadget: Add checking for g-tx-fifo-size parameterSevak Arakelyan1-0/+35
Add dwc2_check_param_tx_fifo_sizes function which validates the members of g_tx_fifo_size array and sets to average or default values if it is needed. Cc: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: gadget: Set TX FIFO depths to calculated defaultsSevak Arakelyan1-4/+8
Remove legacy DWC2_G_P_LEGACY_TX_FIFO_SIZE array for TX FIFOs. Update dwc2_set_param_tx_fifo_sizes function to calculate and assign default average FIFO depth to each member of g_tx_fifo_size array. Total FIFO size, EP Info block's size, FIFO operation mode and device operation mode are taken into consideration during the calculation. Cc: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Add a quirk to allow speed negotiation for Hisilicon Hi6220Chen Yu1-0/+1
The Hi6220's usb controller is limited in that it does not support "Split Transactions", so it does not support communicating with low-speed and full-speed devices behind a high-speed hub. Thus it requires a quirk so that we can manually drop the usb speed when low/full-speed are attached, and bump back to high speed when they are removed. Cc: Wei Xu <xuwei5@hisilicon.com> Cc: Guodong Xu <guodong.xu@linaro.org> Cc: Amit Pundir <amit.pundir@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: John Youn <johnyoun@synopsys.com> Cc: Douglas Anderson <dianders@chromium.org> Cc: Chen Yu <chenyu56@huawei.com> Cc: Vardan Mikayelyan <mvardan@synopsys.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Signed-off-by: Chen Yu <chenyu56@huawei.com> [jstultz: Reworked to simplify the patch, and made commit log to be more specific about the issue] Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Remove debug prints in params.cJohn Youn1-56/+0
Remove debugging prints to show params. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Remove unnecessary parametersJohn Youn1-11/+0
Further reduce the set of parameters set by platforms. Many of them are unnecessary as they should be reported by hardware. They should only need to be overridden if there is a problem. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Fix usage of bool paramsJohn Youn1-2/+2
Check these parameters only for true or false. There is no need to check for greater or less than 0. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Remove platform static paramsJohn Youn1-154/+108
Remove the platform-specific static param structs and set only those params that are necessary for each platform. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Check core parametersJohn Youn1-0/+185
Check that core parameters have valid values and adjust them if they aren't. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Get device propertiesJohn Youn1-0/+35
After setting the default core parameter values, read in the device properties and modify core parameter values if needed. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Set core parameters to default valuesJohn Youn1-915/+75
Initialize the core parameters to their default, auto-detected values. Remove all the previous dwc2_set_param* methods. Most of what this code is doing is handling defaults for "not set" values and other trivial checks. The checking can be simplified and will be done in a later commit. This allows us to change only those parameters that won't work with default settings. It also allows us to use non-int parameters. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Remove unused otg_ver parameterJohn Youn1-23/+0
The otg_ver parameter only controls the SRP pulsing method and defaults to the 1.3 behavior. It is unused and can be removed. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Fix lines over 80 charactersJohn Youn1-7/+7
Fix lines over 80 characters. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: Cleanup some checkpatch issuesJohn Youn1-7/+7
This commmit is the result of running checkpatch --fix. The results were verified for correctness. Some of the fixes result in line over 80 char which we will fix manually later. The following is a summary of what was done by checkpatch: * Remove externs on function prototypes. * Replace symbolic permissions with octal. * Align code to open parens. * Replace 'unsigned' with 'unsigned int'. * Remove unneccessary blank lines. * Add blank lines after declarations. * Add spaces around operators. * Remove unnecessary spaces after casts. * Replace 'x == NULL' with '!x'. * Replace kzalloc() with kcalloc(). * Concatenate multi-line strings. * Use the BIT() macro. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24usb: dwc2: use u32 for DT binding parametersLeo Yan1-5/+5
Commit 05ee799f2021 ("usb: dwc2: Move gadget settings into core_params") changes to type u16 for DT binding "g-rx-fifo-size" and "g-np-tx-fifo-size" but use type u32 for "g-tx-fifo-size". Finally the the first two parameters cannot be passed successfully with wrong data format. This is found the data transferring broken on 96boards Hikey. This patch is to change all parameters to u32 type, and verified on Hikey board the DT parameters can pass successfully. [johnyoun: minor rebase] Signed-off-by: Leo Yan <leo.yan@linaro.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Tested-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02usb: dwc2: gadget: fix default value for gadget-dma-descStefan Wahren1-1/+1
The current default for gadget DMA descriptor results on bcm2835 in a unnecessary error message: Invalid value 1 for param gadget-dma-desc So fix this by using hw->dma_desc_enable as default value. Fixes: dec4b55677e ("usb: dwc2: gadget: Add descriptor DMA parameter") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02usb: dwc2: fix default value for DMA supportStefan Wahren1-2/+2
The current defaults for DMA results on a non-DMA platform in a unnecessary error message: Invalid value 0 for param gadget-dma So fix this by using dma_capable as default value. Fixes: 9962b62f1be ("usb: dwc2: Deprecate g-use-dma binding") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02usb: dwc2: fix dwc2_get_device_property for u8 and u16Stefan Wahren1-12/+0
According to the Devicetree ePAPR [1] the datatypes u8 and u16 are not defined. So using device_property_read_u16() would result in a partial read of a 32-bit big-endian integer which is not intended. So we better read the complete 32-bit value. This fixes a regression on bcm2835 where the values for g-rx-fifo-size and g-np-tx-fifo-size always read as zero: Invalid value 0 for param g-rx-fifo-size Invalid value 0 for param g-np-tx-fifo-size [1] - http://elinux.org/images/c/cf/Power_ePAPR_APPROVED_v1.1.pdf Fixes: 05ee799f202 ("usb: dwc2: Move gadget settings into core_params") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02usb: dwc2: Do not set host parameter in peripheral modeStefan Wahren1-6/+6
Since commit "usb: dwc2: Improve handling of host and device hwparams" the host mode specific hardware parameter aren't initialized in peripheral mode from the register settings anymore. So we better do not set them in this case which avoids the following warnings on bcm2835: 256 invalid for host_nperio_tx_fifo_size. Check HW configuration. 512 invalid for host_perio_tx_fifo_size. Check HW configuration. Fixes: 55e1040e424b ("usb: dwc2: Improve handling of host and device hwparams") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: add amcc,dwc-otg supportChristian Lamparter1-0/+1
This patch adds support for the "amcc,usb-otg" device which is found in the PowerPC Canyonlands' dts. The device definition was added by: commit c89b3458d8cc ("powerpc/44x: Add USB DWC DTS entry to Canyonlands board") but without any driver support as the dwc2 driver wasn't available at that time. Note: The system can't use the generic "snps,dwc2" compatible because of the special ahbcfg configuration. The default GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang when the USB and SATA is used concurrently. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: fixes host_dma logicChristian Lamparter1-3/+2
This patch moves the the host_dma initialization before dwc2_set_param_dma_desc_enable() and dwc2_set_param_dma_desc_fs_enable(). The reason being that both function need it. Fixes: 1205489cee75bf39 ("usb: dwc2: Get host DMA device properties") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: gadget: Add new core parameter for low speedVardan Mikayelyan1-2/+6
Added new core param for low speed, which can be used only when SNPSID is equal to DWC2_CORE_FS_IOT. When LS mode is enabled, we are restricting ep types and providing to upper layer only INTR and CTRL endpoints. Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: gadget: Add IOT device IDs, configure core accordinglyVardan Mikayelyan1-1/+8
Add new device IDs for IOT gadget. Done changes in probe to configure core accordingly depending on device ID value. Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Remove reading in of invalid propertyJohn Youn1-6/+1
This property was mistakenly added, then removed, so don't read it in. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: gadget: Add descriptor DMA parameterVahram Aharonyan1-0/+6
Add a parameter for descriptor DMA and set it based on hardware capabilities. This won't actually be used by the gadget until later, when the descriptor DMA code is in place. Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Deprecate g-use-dma bindingJohn Youn1-3/+14
This is not needed as the gadget now fully supports DMA and it can autodetect it. This was initially added because gadget DMA mode was only partially implemented so could not be automatically enabled. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Get host DMA device propertiesJohn Youn1-30/+18
The driver will automatically enable host DMA and use it if available. This is consistent with the behavior of all existing platforms. Read in the "snps,host-dma-disable" device property to disable it. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Rename the dma_enable parameter to host_dmaJohn Youn1-15/+15
Rename it so that it is more consistent with the gadget dma parameter. It only affects host-mode operation so prefix it with "host". Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Move gadget settings into core_paramsJohn Youn1-4/+258
Move the gadget devicetree settings into the core_params structure and document them. Then set and check them in params.c, with the addition of some helper functions, and remove the equivalent code in gadget.c. Because these parameters came from the standalone s3c driver, they have a fixed default value rather than an autodetected one. Preserve and document this behavior to avoid any compatibility issues. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Rename host_rx_fifo_size hardware parameterJohn Youn1-5/+5
This hardware parameter is not host specific. It also applies to device mode. Drop the "host" from the name to make that clear. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Remove unnecessary prototypesJohn Youn1-28/+34
Remove the unnecessary prototypes for all the parameter setting functions and declare those functions 'static' in the params.c file. Also remove the duplicate documentation that went along with them. They are already documented as part of the params structure definition. Then move the constants that went along with the prototype into the structure. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Remove dwc2_set_all_params functionJohn Youn1-34/+44
Replace this by statically defining a function with defaults, and just assigning it. This will allow us to use parameters of any type and any default value. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Move parameter initialization into params.cJohn Youn1-0/+29
Consolidate and move all the parameter initialization code from the probe function to params.c. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Declare the core params struct staticallyJohn Youn1-34/+34
This makes it consistent with the hw_params struct and simplifies the memory management for future refactoring. Fix up usage in all files. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc2: Add params.c fileJohn Youn1-0/+1125
Add a params.c file and move all driver parameter code there, including all the static parameter definitions. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-23 04:43:17 +0300