summaryrefslogtreecommitdiff
path: root/drivers/usb/core
AgeCommit message (Collapse)AuthorFilesLines
2020-01-23usb: core: hub: Improved device recognition on remote wakeupKeiya Nobuta1-0/+1
commit 9c06ac4c83df6d6fbdbf7488fbad822b4002ba19 upstream. If hub_activate() is called before D+ has stabilized after remote wakeup, the following situation might occur: __ ___________________ / \ / D+ __/ \__/ Hub _______________________________ | ^ ^ ^ | | | | Host _____v__|___|___________|______ | | | | | | | \-- Interrupt Transfer (*3) | | \-- ClearPortFeature (*2) | \-- GetPortStatus (*1) \-- Host detects remote wakeup - D+ goes high, Host starts running by remote wakeup - D+ is not stable, goes low - Host requests GetPortStatus at (*1) and gets the following hub status: - Current Connect Status bit is 0 - Connect Status Change bit is 1 - D+ stabilizes, goes high - Host requests ClearPortFeature and thus Connect Status Change bit is cleared at (*2) - After waiting 100 ms, Host starts the Interrupt Transfer at (*3) - Since the Connect Status Change bit is 0, Hub returns NAK. In this case, port_event() is not called in hub_event() and Host cannot recognize device. To solve this issue, flag change_bits even if only Connect Status Change bit is 1 when got in the first GetPortStatus. This issue occurs rarely because it only if D+ changes during a very short time between GetPortStatus and ClearPortFeature. However, it is fatal if it occurs in embedded system. Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200109051448.28150-1-nobuta.keiya@fujitsu.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14USB: Fix: Don't skip endpoint descriptors with maxpacket=0Alan Stern1-4/+8
commit 2548288b4fb059b2da9ceada172ef763077e8a59 upstream. It turns out that even though endpoints with a maxpacket length of 0 aren't useful for data transfer, the descriptors do serve other purposes. In particular, skipping them will also skip over other class-specific descriptors for classes such as UVC. This unexpected side effect has caused some UVC cameras to stop working. In addition, the USB spec requires that when isochronous endpoint descriptors are present in an interface's altsetting 0 (which is true on some devices), the maxpacket size _must_ be set to 0. Warning about such things seems like a bad idea. This patch updates an earlier commit which would log a warning and skip these endpoint descriptors. Now we only log a warning, and we don't even do that for isochronous endpoints in altsetting 0. We don't need to worry about preventing endpoints with maxpacket = 0 from ever being used for data transfers; usb_submit_urb() already checks for this. Reported-and-tested-by: Roger Whittaker <Roger.Whittaker@suse.com> Fixes: d482c7bb0541 ("USB: Skip endpoints with 0 maxpacket length") Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2 Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-12usb: missing parentheses in USE_NEW_SCHEMEQi Zhou1-1/+1
commit 1530f6f5f5806b2abbf2a9276c0db313ae9a0e09 upstream. According to bd0e6c9614b9 ("usb: hub: try old enumeration scheme first for high speed devices") the kernel will try the old enumeration scheme first for high speed devices. This can happen when a high speed device is plugged in. But due to missing parentheses in the USE_NEW_SCHEME define, this logic can get messed up and the incorrect result happens. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Qi Zhou <atmgnd@outlook.com> Link: https://lore.kernel.org/r/ht4mtag8ZP-HKEhD0KkJhcFnVlOFV8N8eNjJVRD9pDkkLUNhmEo8_cL_sl7xy9mdajdH-T8J3TFQsjvoYQT61NFjQXy469Ed_BbBw_x4S1E=@protonmail.com [ fixup changelog text - gregkh] Cc: stable <stable@vger.kernel.org> Fixes: bd0e6c9614b9 ("usb: hub: try old enumeration scheme first for high speed devices") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-12USB: core: fix check for duplicate endpointsJohan Hovold1-12/+58
commit 3e4f8e21c4f27bcf30a48486b9dcc269512b79ff upstream. Amend the endpoint-descriptor sanity checks to detect all duplicate endpoint addresses in a configuration. Commit 0a8fd1346254 ("USB: fix problems with duplicate endpoint addresses") added a check for duplicate endpoint addresses within a single alternate setting, but did not look for duplicate addresses in other interfaces. The current check would also not detect all duplicate addresses when one endpoint is as a (bi-directional) control endpoint. This specifically avoids overwriting the endpoint entries in struct usb_device when enabling a duplicate endpoint, something which could potentially lead to crashes or leaks, for example, when endpoints are later disabled. Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20191219161016.6695-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-31usb: usbfs: Suppress problematic bind and unbind uevents.Ingo Rohloff1-1/+14
[ Upstream commit abb0b3d96a1f9407dd66831ae33985a386d4200d ] commit 1455cf8dbfd0 ("driver core: emit uevents when device is bound to a driver") added bind and unbind uevents when a driver is bound or unbound to a physical device. For USB devices which are handled via the generic usbfs layer (via libusb for example), this is problematic: Each time a user space program calls ioctl(usb_fd, USBDEVFS_CLAIMINTERFACE, &usb_intf_nr); and then later ioctl(usb_fd, USBDEVFS_RELEASEINTERFACE, &usb_intf_nr); The kernel will now produce a bind or unbind event, which does not really contain any useful information. This allows a user space program to run a DoS attack against programs which listen to uevents (in particular systemd/eudev/upowerd): A malicious user space program just has to call in a tight loop ioctl(usb_fd, USBDEVFS_CLAIMINTERFACE, &usb_intf_nr); ioctl(usb_fd, USBDEVFS_RELEASEINTERFACE, &usb_intf_nr); With this loop the malicious user space program floods the kernel and all programs listening to uevents with tons of bind and unbind events. This patch suppresses uevents for ioctls USBDEVFS_CLAIMINTERFACE and USBDEVFS_RELEASEINTERFACE. Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com> Link: https://lore.kernel.org/r/20191011115518.2801-1-ingo.rohloff@lauterbach.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-17usb: core: urb: fix URB structure initialization functionEmiliano Ingrassia1-0/+1
commit 1cd17f7f0def31e3695501c4f86cd3faf8489840 upstream. Explicitly initialize URB structure urb_list field in usb_init_urb(). This field can be potentially accessed uninitialized and its initialization is coherent with the usage of list_del_init() in usb_hcd_unlink_urb_from_ep() and usb_giveback_urb_bh() and its explicit initialization in usb_hcd_submit_urb() error path. Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191127160355.GA27196@ingrassia.epigenesys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17usb: Allow USB device to be warm reset in suspended stateKai-Heng Feng1-3/+2
commit e76b3bf7654c3c94554c24ba15a3d105f4006c80 upstream. On Dell WD15 dock, sometimes USB ethernet cannot be detected after plugging cable to the ethernet port, the hub and roothub get runtime resumed and runtime suspended immediately: ... [ 433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0 [ 433.315204] usb usb4: usb auto-resume [ 433.315226] hub 4-0:1.0: hub_resume [ 433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343 [ 433.315264] usb usb4-port1: status 0343 change 0001 [ 433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2 [ 433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0 [ 433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343 [ 433.422307] usb usb4-port1: do warm reset [ 433.422311] usb 4-1: device reset not allowed in state 8 [ 433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000 [ 433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343 [ 433.422356] usb usb4-port1: do warm reset [ 433.422358] usb 4-1: device reset not allowed in state 8 [ 433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status = 0xf0002e2 [ 433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status = 0xe0002a0 [ 433.422465] hub 4-0:1.0: hub_suspend [ 433.422475] usb usb4: bus auto-suspend, wakeup 1 [ 433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling. [ 433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001 [ 433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0 [ 433.862445] xhci_hcd 0000:3a:00.0: PME# enabled [ 433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20) [ 433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403) [ 433.902490] xhci_hcd 0000:3a:00.0: PME# disabled [ 433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering [ 433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001 [ 433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt! [ 433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2 [ 433.902842] xhci_hcd 0000:3a:00.0: resume root hub [ 433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling. [ 433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling. [ 433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0 [ 433.902919] usb usb4: usb wakeup-resume [ 433.902942] usb usb4: usb auto-resume [ 433.902966] hub 4-0:1.0: hub_resume ... As Mathias pointed out, the hub enters Cold Attach Status state and requires a warm reset. However usb_reset_device() bails out early when the device is in suspended state, as its callers port_event() and hub_event() don't always resume the device. Since there's nothing wrong to reset a suspended device, allow usb_reset_device() to do so to solve the issue. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191106062710.29880-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-12USB: Skip endpoints with 0 maxpacket lengthAlan Stern1-0/+5
[ Upstream commit d482c7bb0541d19dea8bff437a9f3c5563b5b2d2 ] Endpoints with a maxpacket length of 0 are probably useless. They can't transfer any data, and it's not at all unlikely that an HCD will crash or hang when trying to handle an URB for such an endpoint. Currently the USB core does not check for endpoints having a maxpacket value of 0. This patch adds a check, printing a warning and skipping over any endpoints it catches. Now, the USB spec does not rule out endpoints having maxpacket = 0. But since they wouldn't have any practical use, there doesn't seem to be any good reason for us to accept them. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281050420.1485-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-06usb: handle warm-reset port requests on hub resumeJan-Marek Glogowski1-0/+7
[ Upstream commit 4fdc1790e6a9ef22399c6bc6e63b80f4609f3b7e ] On plug-in of my USB-C device, its USB_SS_PORT_LS_SS_INACTIVE link state bit is set. Greping all the kernel for this bit shows that the port status requests a warm-reset this way. This just happens, if its the only device on the root hub, the hub therefore resumes and the HCDs status_urb isn't yet available. If a warm-reset request is detected, this sets the hubs event_bits, which will prevent any auto-suspend and allows the hubs workqueue to warm-reset the port later in port_event. Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-09-21USB: usbcore: Fix slab-out-of-bounds bug during device resetAlan Stern1-4/+8
commit 3dd550a2d36596a1b0ee7955da3b611c031d3873 upstream. The syzbot fuzzer provoked a slab-out-of-bounds error in the USB core: BUG: KASAN: slab-out-of-bounds in memcmp+0xa6/0xb0 lib/string.c:904 Read of size 1 at addr ffff8881d175bed6 by task kworker/0:3/2746 CPU: 0 PID: 2746 Comm: kworker/0:3 Not tainted 5.3.0-rc5+ #28 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 memcmp+0xa6/0xb0 lib/string.c:904 memcmp include/linux/string.h:400 [inline] descriptors_changed drivers/usb/core/hub.c:5579 [inline] usb_reset_and_verify_device+0x564/0x1300 drivers/usb/core/hub.c:5729 usb_reset_device+0x4c1/0x920 drivers/usb/core/hub.c:5898 rt2x00usb_probe+0x53/0x7af drivers/net/wireless/ralink/rt2x00/rt2x00usb.c:806 The error occurs when the descriptors_changed() routine (called during a device reset) attempts to compare the old and new BOS and capability descriptors. The length it uses for the comparison is the wTotalLength value stored in BOS descriptor, but this value is not necessarily the same as the length actually allocated for the descriptors. If it is larger the routine will call memcmp() with a length that is too big, thus reading beyond the end of the allocated region and leading to this fault. The kernel reads the BOS descriptor twice: first to get the total length of all the capability descriptors, and second to read it along with all those other descriptors. A malicious (or very faulty) device may send different values for the BOS descriptor fields each time. The memory area will be allocated using the wTotalLength value read the first time, but stored within it will be the value read the second time. To prevent this possibility from causing any errors, this patch modifies the BOS descriptor after it has been read the second time: It sets the wTotalLength field to the actual length of the descriptors that were read in and validated. Then the memcpy() call, or any other code using these descriptors, will be able to rely on wTotalLength being valid. Reported-and-tested-by: syzbot+35f4d916c623118d576e@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909041154260.1722-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-06usb: hcd: use managed device resourcesSchmid, Carsten1-22/+8
commit 76da906ad727048a74bb8067031ee99fc070c7da upstream. Using managed device resources in usb_hcd_pci_probe() allows devm usage for resource subranges, such as the mmio resource for the platform device created to control host/device mode mux, which is a xhci extended capability, and sits inside the xhci mmio region. If managed device resources are not used then "parent" resource is released before subrange at driver removal as .remove callback is called before the devres list of resources for this device is walked and released. This has been observed with the xhci extended capability driver causing a use-after-free which is now fixed. An additional nice benefit is that error handling on driver initialisation is simplified much. Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com> Tested-by: Carsten Schmid <carsten_schmid@mentor.com> Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com> Fixes: fa31b3cb2ae1 ("xhci: Add Intel extended cap / otg phy mux handling") Cc: <stable@vger.kernel.org> # v4.19+ Link: https://lore.kernel.org/r/1566569488679.31808@mentor.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-25USB: CDC: fix sanity checks in CDC union parserOliver Neukum1-2/+2
commit 54364278fb3cabdea51d6398b07c87415065b3fc upstream. A few checks checked for the size of the pointer to a structure instead of the structure itself. Copy & paste issue presumably. Fixes: e4c6fb7794982 ("usbnet: move the CDC parser into USB core") Cc: stable <stable@vger.kernel.org> Reported-by: syzbot+45a53506b65321c1fe91@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20190813093541.18889-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-25USB: core: Fix races in character device registration and deregistraionAlan Stern1-5/+5
commit 303911cfc5b95d33687d9046133ff184cf5043ff upstream. The syzbot fuzzer has found two (!) races in the USB character device registration and deregistration routines. This patch fixes the races. The first race results from the fact that usb_deregister_dev() sets usb_minors[intf->minor] to NULL before calling device_destroy() on the class device. This leaves a window during which another thread can allocate the same minor number but will encounter a duplicate name error when it tries to register its own class device. A typical error message in the system log would look like: sysfs: cannot create duplicate filename '/class/usbmisc/ldusb0' The patch fixes this race by destroying the class device first. The second race is in usb_register_dev(). When that routine runs, it first allocates a minor number, then drops minor_rwsem, and then creates the class device. If the device creation fails, the minor number is deallocated and the whole routine returns an error. But during the time while minor_rwsem was dropped, there is a window in which the minor number is allocated and so another thread can successfully open the device file. Typically this results in use-after-free errors or invalid accesses when the other thread closes its open file reference, because the kernel then tries to release resources that were already deallocated when usb_register_dev() failed. The patch fixes this race by keeping minor_rwsem locked throughout the entire routine. Reported-and-tested-by: syzbot+30cf45ebfe0b0c4847a1@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908121607590.1659-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-16usb: usbfs: fix double-free of usb memory upon submiturb errorGavin Li1-2/+0
commit c43f28dfdc4654e738aa6d3fd08a105b2bee758d upstream. Upon an error within proc_do_submiturb(), dec_usb_memory_use_count() gets called once by the error handling tail and again by free_async(). Remove the first call. Signed-off-by: Gavin Li <git@thegavinli.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190804235044.22327-1-gavinli@thegavinli.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-31usb: core: hub: Disable hub-initiated U1/U2Thinh Nguyen1-12/+16
[ Upstream commit 561759292774707b71ee61aecc07724905bb7ef1 ] If the device rejects the control transfer to enable device-initiated U1/U2 entry, then the device will not initiate U1/U2 transition. To improve the performance, the downstream port should not initate transition to U1/U2 to avoid the delay from the device link command response (no packet can be transmitted while waiting for a response from the device). If the device has some quirks and does not implement U1/U2, it may reject all the link state change requests, and the downstream port may resend and flood the bus with more requests. This will affect the device performance even further. This patch disables the hub-initated U1/U2 if the device-initiated U1/U2 entry fails. Reference: USB 3.2 spec 7.2.4.2.3 Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-07-26usb: Handle USB3 remote wakeup for LPM enabled devices correctlyLee, Chiasheng1-2/+5
commit e244c4699f859cf7149b0781b1894c7996a8a1df upstream. With Link Power Management (LPM) enabled USB3 links transition to low power U1/U2 link states from U0 state automatically. Current hub code detects USB3 remote wakeups by checking if the software state still shows suspended, but the link has transitioned from suspended U3 to enabled U0 state. As it takes some time before the hub thread reads the port link state after a USB3 wake notification, the link may have transitioned from U0 to U1/U2, and wake is not detected by hub code. Fix this by handling U1/U2 states in the same way as U0 in USB3 wakeup handling This patch should be added to stable kernels since 4.13 where LPM was kept enabled during suspend/resume Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by: Lee, Chiasheng <chiasheng.lee@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19USB: Fix chipmunk-like voice when using Logitech C270 for recording audio.Marco Zatta1-0/+3
commit bd21f0222adab64974b7d1b4b8c7ce6b23e9ea4d upstream. This patch fixes the chipmunk-like voice that manifets randomly when using the integrated mic of the Logitech Webcam HD C270. The issue was solved initially for this device by commit 2394d67e446b ("USB: add RESET_RESUME for webcams shown to be quirky") but it was then reintroduced by e387ef5c47dd ("usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams"). This patch is to have the fix back. Signed-off-by: Marco Zatta <marco@zatta.me> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-09USB: Add LPM quirk for Surface Dock GigE adapterMaximilian Luz1-0/+3
commit ea261113385ac0a71c2838185f39e8452d54b152 upstream. Without USB_QUIRK_NO_LPM ethernet will not work and rtl8152 will complain with r8152 <device...>: Stop submitting intr, status -71 Adding the quirk resolves this. As the dock is externally powered, this should not have any drawbacks. Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-09USB: Fix slab-out-of-bounds write in usb_get_bos_descriptorAlan Stern1-2/+2
commit a03ff54460817c76105f81f3aa8ef655759ccc9a upstream. The syzkaller USB fuzzer found a slab-out-of-bounds write bug in the USB core, caused by a failure to check the actual size of a BOS descriptor. This patch adds a check to make sure the descriptor is at least as large as it is supposed to be, so that the code doesn't inadvertently access memory beyond the end of the allocated region when assigning to dev->bos->desc->bNumDeviceCaps later on. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+71f1e64501a309fcc012@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-31usb: core: Add PM runtime calls to usb_hcd_platform_shutdownTony Lindgren1-0/+3
[ Upstream commit 8ead7e817224d7832fe51a19783cb8fcadc79467 ] If ohci-platform is runtime suspended, we can currently get an "imprecise external abort" on reboot with ohci-platform loaded when PM runtime is implemented for the SoC. Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown. Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31USB: core: Don't unbind interfaces following device reset failureAlan Stern1-1/+4
[ Upstream commit 381419fa720060ba48b7bbc483be787d5b1dca6f ] The SCSI core does not like to have devices or hosts unregistered while error recovery is in progress. Trying to do so can lead to self-deadlock: Part of the removal code tries to obtain a lock already held by the error handler. This can cause problems for the usb-storage and uas drivers, because their error handler routines perform a USB reset, and if the reset fails then the USB core automatically goes on to unbind all drivers from the device's interfaces -- all while still in the context of the SCSI error handler. As it turns out, practically all the scenarios leading to a USB reset failure end up causing a device disconnect (the main error pathway in usb_reset_and_verify_device(), at the end of the routine, calls hub_port_logical_disconnect() before returning). As a result, the hub_wq thread will soon become aware of the problem and will unbind all the device's drivers in its own context, not in the error-handler's context. This means that usb_reset_device() does not need to call usb_unbind_and_rebind_marked_interfaces() in cases where usb_reset_and_verify_device() has returned an error, because hub_wq will take care of everything anyway. This particular problem was observed in somewhat artificial circumstances, by using usbfs to tell a hub to power-down a port connected to a USB-3 mass storage device using the UAS protocol. With the port turned off, the currently executing command timed out and the error handler started running. The USB reset naturally failed, because the hub port was off, and the error handler deadlocked as described above. Not carrying out the call to usb_unbind_and_rebind_marked_interfaces() fixes this issue. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> Tested-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> CC: Bart Van Assche <bvanassche@acm.org> CC: Martin K. Petersen <martin.petersen@oracle.com> CC: Jacky Cao <Jacky.Cao@sony.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-08USB: core: Fix bug caused by duplicate interface PM usage counterAlan Stern1-13/+0
commit c2b71462d294cf517a0bc6e4fd6424d7cee5596f upstream. The syzkaller fuzzer reported a bug in the USB hub driver which turned out to be caused by a negative runtime-PM usage counter. This allowed a hub to be runtime suspended at a time when the driver did not expect it. The symptom is a WARNING issued because the hub's status URB is submitted while it is already active: URB 0000000031fb463e submitted while active WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363 The negative runtime-PM usage count was caused by an unfortunate design decision made when runtime PM was first implemented for USB. At that time, USB class drivers were allowed to unbind from their interfaces without balancing the usage counter (i.e., leaving it with a positive count). The core code would take care of setting the counter back to 0 before allowing another driver to bind to the interface. Later on when runtime PM was implemented for the entire kernel, the opposite decision was made: Drivers were required to balance their runtime-PM get and put calls. In order to maintain backward compatibility, however, the USB subsystem adapted to the new implementation by keeping an independent usage counter for each interface and using it to automatically adjust the normal usage counter back to 0 whenever a driver was unbound. This approach involves duplicating information, but what is worse, it doesn't work properly in cases where a USB class driver delays decrementing the usage counter until after the driver's disconnect() routine has returned and the counter has been adjusted back to 0. Doing so would cause the usage counter to become negative. There's even a warning about this in the USB power management documentation! As it happens, this is exactly what the hub driver does. The kick_hub_wq() routine increments the runtime-PM usage counter, and the corresponding decrement is carried out by hub_event() in the context of the hub_wq work-queue thread. This work routine may sometimes run after the driver has been unbound from its interface, and when it does it causes the usage counter to go negative. It is not possible for hub_disconnect() to wait for a pending hub_event() call to finish, because hub_disconnect() is called with the device lock held and hub_event() acquires that lock. The only feasible fix is to reverse the original design decision: remove the duplicate interface-specific usage counter and require USB drivers to balance their runtime PM gets and puts. As far as I know, all existing drivers currently do this. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-08USB: core: Fix unterminated string returned by usb_string()Alan Stern1-1/+3
commit c01c348ecdc66085e44912c97368809612231520 upstream. Some drivers (such as the vub300 MMC driver) expect usb_string() to return a properly NUL-terminated string, even when an error occurs. (In fact, vub300's probe routine doesn't bother to check the return code from usb_string().) When the driver goes on to use an unterminated string, it leads to kernel errors such as stack-out-of-bounds, as found by the syzkaller USB fuzzer. An out-of-range string index argument is not at all unlikely, given that some devices don't provide string descriptors and therefore list 0 as the value for their string indexes. This patch makes usb_string() return a properly terminated empty string along with the -EINVAL error code when an out-of-range index is encountered. And since a USB string index is a single-byte value, indexes >= 256 are just as invalid as values of 0 or below. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-02USB: Consolidate LPM checks to avoid enabling LPM twiceKai-Heng Feng3-13/+13
commit d7a6c0ce8d26412903c7981503bad9e1cc7c45d2 upstream. USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working after S3: [ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin [ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110) After some experiments, I found that disabling LPM can workaround the issue. On some platforms, the USB power is cut during S3, so the driver uses reset-resume to resume the device. During port resume, LPM gets enabled twice, by usb_reset_and_verify_device() and usb_port_resume(). Consolidate all checks into new LPM helpers to make sure LPM only gets enabled once. Fixes: de68bab4fa96 ("usb: Don't enable USB 2.0 Link PM by default.”) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> # after much soaking Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-02USB: Add new USB LPM helpersKai-Heng Feng5-11/+30
commit 7529b2574a7aaf902f1f8159fbc2a7caa74be559 upstream. Use new helpers to make LPM enabling/disabling more clear. This is a preparation to subsequent patch. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> # after much soaking Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-12usb: hub: delay hub autosuspend if USB3 port is still link trainingMathias Nyman1-0/+10
[ Upstream commit e86108940e541febf35813402ff29fa6f4a9ac0b ] When initializing a hub we want to give a USB3 port in link training the same debounce delay time before autosuspening the hub as already trained, connected enabled ports. USB3 ports won't reach the enabled state with "current connect status" and "connect status change" bits set until the USB3 link training finishes. Catching the port in link training (polling) and adding the debounce delay prevents unnecessary failed attempts to autosuspend the hub. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-01-31USB: leds: fix regression in usbport led triggerChristian Lamparter1-7/+10
commit 91f7d2e89868fcac0e750a28230fdb1ad4512137 upstream. The patch "usb: simplify usbport trigger" together with "leds: triggers: add device attribute support" caused an regression for the usbport trigger. it will no longer enumerate any active usb hub ports under the "ports" directory in the sysfs class directory, if the usb host drivers are fully initialized before the usbport trigger was loaded. The reason is that the usbport driver tries to register the sysfs entries during the activate() callback. And this will fail with -2 / ENOENT because the patch "leds: triggers: add device attribute support" made it so that the sysfs "ports" group was only being added after the activate() callback succeeded. This version of the patch reverts parts of the "usb: simplify usbport trigger" patch and restores usbport trigger's functionality. Fixes: 6f7b0bad8839 ("usb: simplify usbport trigger") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-17USB: Add USB_QUIRK_DELAY_CTRL_MSG quirk for Corsair K70 RGBJack Stocker1-1/+2
commit 3483254b89438e60f719937376c5e0ce2bc46761 upstream. To match the Corsair Strafe RGB, the Corsair K70 RGB also requires USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues discussed here: https://github.com/ckb-next/ckb-next/issues/42. Otherwise roughly 1 in 10 boots the keyboard will fail to be detected. Patch that applied delay control quirk for Corsair Strafe RGB: cb88a0588717 ("usb: quirks: add control message delay for 1b1c:1b20") Previous K70 RGB patch to add delay-init quirk: 7a1646d92257 ("Add delay-init quirk for Corsair K70 RGB keyboards") Signed-off-by: Jack Stocker <jackstocker.93@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-13USB: check usb_get_extra_descriptor for proper sizeMathias Payer2-4/+4
commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream. When reading an extra descriptor, we need to properly check the minimum and maximum size allowed, to prevent from invalid data being sent by a device. Reported-by: Hui Peng <benquike@gmail.com> Reported-by: Mathias Payer <mathias.payer@nebelwelt.net> Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Hui Peng <benquike@gmail.com> Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-13usb: quirk: add no-LPM quirk on SanDisk Ultra Flair deviceHarry Pan1-0/+4
commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream. Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is in 0781:5591, will aggressively request LPM of U1/U2 during runtime, when using this thumb drive as the OS installation key we found the device will generate failure during U1 exit path making it dropped from the USB bus, this causes a corrupted installation in system at the end. i.e., [ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004 [ 166.918327] usb usb2-port2: link state change [ 166.918337] usb usb2-port2: do warm reset [ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms [ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms [ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s [ 167.276050] usb 2-2: USB disconnect, device number 2 [ 167.276058] usb 2-2: unregistering device [ 167.276060] usb 2-2: unregistering interface 2-2:1.0 [ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk [ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00 ... Analyzed the USB trace in the link layer we realized it is because of the 6-ms timer of tRecoveryConfigurationTimeout which documented on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from Recovery.Configuration"; device initiates U1 exit -> Recovery.Active -> Recovery.Configuration, then the host timer timeout makes the link transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset. Interestingly, the other higher volume of SanDisk Ultra Flair sharing the same VID:PID, such as 64GB, would not request LPM during runtime, it sticks at U0 always, thus disabling LPM does not affect those thumb drives at all. The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583. Signed-off-by: Harry Pan <harry.pan@intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: core: quirks: add RESET_RESUME quirk for Cherry G230 Stream seriesMichael Niewöhner1-0/+3
commit effd14f66cc1ef6701a19c5a56e39c35f4d395a5 upstream. Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to function correctly. This fixes a but where double pressing numlock locks up the device completely with need to replug the keyboard. Signed-off-by: Michael Niewöhner <linux@mniewoehner.de> Tested-by: Michael Niewöhner <linux@mniewoehner.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-01usb: core: Fix hub port connection events lostDennis Wassenberg1-1/+3
commit 22454b79e6de05fa61a2a72d00d2eed798abbb75 upstream. This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset only if a device is was attached to the hub port before resetting the hub port. Using a Lenovo T480s attached to the ultra dock it was not possible to detect some usb-c devices at the dock usb-c ports because the hub_port_reset code will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset. Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit. This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the new device was attached such that it was not detected. This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is currently no device attached to the port before the hub port reset. This will avoid clearing the connection bit for new attached devices. Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com> Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-27usb: quirks: Add delay-init quirk for Corsair K70 LUX RGBEmmanuel Pescosta1-0/+3
commit a77112577667cbda7c6292c52d909636aef31fd9 upstream. Following on from this patch: https://lkml.org/lkml/2017/11/3/516, Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to start correctly at boot. Dmesg output: usb 1-6: string descriptor 0 read error: -110 usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33 usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-6: can't set config #1, error -110 Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-27USB: Wait for extra delay time after USB_PORT_FEAT_RESET for quirky hubKai-Heng Feng2-3/+17
commit 781f0766cc41a9dd2e5d118ef4b1d5d89430257b upstream. Devices connected under Terminus Technology Inc. Hub (1a40:0101) may fail to work after the system resumes from suspend: [ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd [ 206.143691] usb 3-2.4: device descriptor read/64, error -32 [ 206.351671] usb 3-2.4: device descriptor read/64, error -32 Info for this hub: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1a40 ProdID=0101 Rev=01.11 S: Product=USB 2.0 Hub C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub Some expirements indicate that the USB devices connected to the hub are innocent, it's the hub itself is to blame. The hub needs extra delay time after it resets its port. Hence wait for extra delay, if the device is connected to this quirky hub. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-27USB: quirks: Add no-lpm quirk for Raydium touchscreensKai-Heng Feng1-0/+5
commit deefd24228a172d1b27d4a9adbfd2cdacd60ae64 upstream. Raydium USB touchscreen fails to set config if LPM is enabled: [ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119 [ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.030660] usb 1-8: Product: Raydium Touch System [ 2.030661] usb 1-8: Manufacturer: Raydium Corporation [ 7.132209] usb 1-8: can't set config #1, error -110 Same behavior can be observed on 2386:3114. Raydium claims the touchscreen supports LPM under Windows, so I used Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows that the LPM doesn't work under Windows, either. So let's just disable LPM for Raydium touchscreens. [1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-16USB: fix the usbfs flag sanitization for control transfersAlan Stern1-2/+2
Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the transfer flags for URBs submitted from userspace via usbfs. However, the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be allowed for a control transfer was added in the wrong place, before the code has properly determined the direction of the control transfer. (Control transfers are special because for them, the direction is set by the bRequestType byte of the Setup packet rather than direction bit of the endpoint address.) This patch moves code which sets up the allow_short flag for control transfers down after is_in has been set to the correct value. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com Fixes: 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") CC: Oliver Neukum <oneukum@suse.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-20usb: core: safely deal with the dynamic quirk listsHarry Pan1-1/+2
Applying dynamic usbcore quirks in early booting when the slab is not yet ready would cause kernel panic of null pointer dereference because the quirk_count has been counted as 1 while the quirk_list was failed to allocate. i.e., [ 1.044970] BUG: unable to handle kernel NULL pointer dereference at (null) [ 1.044995] IP: [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1 [ 1.045016] PGD 0 [ 1.045026] Oops: 0000 [#1] PREEMPT SMP [ 1.046986] gsmi: Log Shutdown Reason 0x03 [ 1.046995] Modules linked in: [ 1.047008] CPU: 0 PID: 81 Comm: kworker/0:3 Not tainted 4.4.154 #28 [ 1.047016] Hardware name: Google Coral/Coral, BIOS Google_Coral.10068.27.0 12/04/2017 [ 1.047028] Workqueue: usb_hub_wq hub_event [ 1.047037] task: ffff88017a321c80 task.stack: ffff88017a384000 [ 1.047044] RIP: 0010:[<ffffffffb0953ec7>] [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1 To tackle this odd, let's balance the quirk_count to 0 when the kcalloc call fails, and defer the quirk setting into a lower level callback which ensures that the kernel memory management has been initialized. Fixes: 027bd6cafd9a ("usb: core: Add "quirks" parameter for usbcore") Signed-off-by: Harry Pan <harry.pan@intel.com> Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-20USB: handle NULL config in usb_find_alt_setting()Alan Stern1-0/+2
usb_find_alt_setting() takes a pointer to a struct usb_host_config as an argument; it searches for an interface with specified interface and alternate setting numbers in that config. However, it crashes if the usb_host_config pointer argument is NULL. Since this is a general-purpose routine, available for use in many places, we want to to be more robust. This patch makes it return NULL whenever the config argument is NULL. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: syzbot+19c3aaef85a89d451eac@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-20USB: fix error handling in usb_driver_claim_interface()Alan Stern1-0/+15
The syzbot fuzzing project found a use-after-free bug in the USB core. The bug was caused by usbfs not unbinding from an interface when the USB device file was closed, which led another process to attempt the unbind later on, after the private data structure had been deallocated. The reason usbfs did not unbind the interface at the appropriate time was because it thought the interface had never been claimed in the first place. This was caused by the fact that usb_driver_claim_interface() does not clean up properly when device_bind_driver() returns an error. Although the error code gets passed back to the caller, the iface->dev.driver pointer remains set and iface->condition remains equal to USB_INTERFACE_BOUND. This patch adds proper error handling to usb_driver_claim_interface(). Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: syzbot+f84aa7209ccec829536f@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-20USB: remove LPM management from usb_driver_claim_interface()Alan Stern1-15/+0
usb_driver_claim_interface() disables and re-enables Link Power Management, but it shouldn't do either one, for the reasons listed below. This patch removes the two LPM-related function calls from the routine. The reason for disabling LPM in the analogous function usb_probe_interface() is so that drivers won't have to deal with unwanted LPM transitions in their probe routine. But usb_driver_claim_interface() doesn't call the driver's probe routine (or any other callbacks), so that reason doesn't apply here. Furthermore, no driver other than usbfs will ever call usb_driver_claim_interface() unless it is already bound to another interface in the same device, which means disabling LPM here would be redundant. usbfs doesn't interact with LPM at all. Lastly, the error return from usb_unlocked_disable_lpm() isn't handled properly; the code doesn't clean up its earlier actions before returning. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Fixes: 8306095fd2c1 ("USB: Disable USB 3.0 LPM in critical sections.") CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-20USB: usbdevfs: restore warning for nonsensical flagsOliver Neukum1-0/+5
If we filter flags before they reach the core we need to generate our own warnings. Signed-off-by: Oliver Neukum <oneukum@suse.com> Fixes: 0cb54a3e47cb ("USB: debugging code shouldn't alter control flow") Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-20USB: usbdevfs: sanitize flags moreOliver Neukum1-3/+16
Requesting a ZERO_PACKET or not is sensible only for output. In the input direction the device decides. Likewise accepting short packets makes sense only for input. This allows operation with panic_on_warn without opening up a local DOS. Signed-off-by: Oliver Neukum <oneukum@suse.com> Reported-by: syzbot+843efa30c8821bd69f53@syzkaller.appspotmail.com Fixes: 0cb54a3e47cb ("USB: debugging code shouldn't alter control flow") Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-10usb: Change usb_of_get_companion_dev() place to usb/commonYoshihiro Shimoda1-26/+0
Since renesas_usb3 udc driver calls usb_of_get_companion_dev() which is on usb/core/of.c, build error like below happens if we disable CONFIG_USB because the usb/core/ needs CONFIG_USB: ERROR: "usb_of_get_companion_dev" [drivers/usb/gadget/udc/renesas_usb3.ko] undefined! According to the usb/gadget/Kconfig, "NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!". So, to fix the issue, this patch changes the usb_of_get_companion_dev() place from usb/core/of.c to usb/common/common.c to be called by both host and gadget. Reported-by: John Garry <john.garry@huawei.com> Fixes: 39facfa01c9f ("usb: gadget: udc: renesas_usb3: Add register of usb role switch") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-05usb: Avoid use-after-free by flushing endpoints early in usb_set_interface()Mathias Nyman1-0/+11
The steps taken by usb core to set a new interface is very different from what is done on the xHC host side. xHC hardware will do everything in one go. One command is used to set up new endpoints, free old endpoints, check bandwidth, and run the new endpoints. All this is done by xHC when usb core asks the hcd to check for available bandwidth. At this point usb core has not yet flushed the old endpoints, which will cause use-after-free issues in xhci driver as queued URBs are cancelled on a re-allocated endpoint. To resolve this add a call to usb_disable_interface() which will flush the endpoints before calling usb_hcd_alloc_bandwidth() Additional checks in xhci driver will also be implemented to gracefully handle stale URB cancel on freed and re-allocated endpoints Cc: <stable@vger.kernel.org> Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-05usb: Don't die twice if PCI xhci host is not responding in resumeMathias Nyman1-2/+0
usb_hc_died() should only be called once, and with the primary HCD as parameter. It will mark both primary and secondary hcd's dead. Remove the extra call to usb_cd_died with the shared hcd as parameter. Fixes: ff9d78b36f76 ("USB: Set usb_hcd->state and flags for shared roothubs") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-05USB: Add quirk to support DJI CineSSDTim Anderson1-0/+3
This device does not correctly handle the LPM operations. Also, the device cannot handle ATA pass-through commands and locks up when attempted while running in super speed. This patch adds the equivalent quirk logic as found in uas. Signed-off-by: Tim Anderson <tsa@biglakesoftware.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-05USB: add quirk for WORLDE Controller KS49 or Prodipe MIDI 49C USB controllerMaxence Duprès1-0/+4
WORLDE Controller KS49 or Prodipe MIDI 49C USB controller cause a -EPROTO error, a communication restart and loop again. This issue has already been fixed for KS25. https://lore.kernel.org/patchwork/patch/753077/ I just add device 201 for KS49 in quirks.c to get it works. Signed-off-by: Laurent Roux <xpros64@hotmail.fr> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-18Merge tag 'usb-4.19-rc1' of ↵Linus Torvalds3-6/+50
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB/PHY updates from Greg KH: "Here is the big USB and phy driver patch set for 4.19-rc1. Nothing huge but there was a lot of work that happened this development cycle: - lots of type-c work, with drivers graduating out of staging, and displayport support being added. - new PHY drivers - the normal collection of gadget driver updates and fixes - code churn to work on the urb handling path, using irqsave() everywhere in anticipation of making this codepath a lot simpler in the future. - usbserial driver fixes and reworks - other misc changes All of these have been in linux-next with no reported issues for a while" * tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits) USB: serial: pl2303: add a new device id for ATEN usb: renesas_usbhs: Kconfig: convert to SPDX identifiers usb: dwc3: gadget: Check MaxPacketSize from descriptor usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms usb: dwc2: Turn on uframe_sched on "amlogic" platforms usb: dwc2: Turn on uframe_sched on "his" platforms usb: dwc2: Turn on uframe_sched on "bcm" platforms usb: dwc2: gadget: ISOC's starting flow improvement usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic. usb: dwc3: core: Enable AutoRetry feature in the controller usb: dwc3: Set default mode for dwc_usb31 usb: gadget: udc: renesas_usb3: Add register of usb role switch usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep usb: dwc2: Modify dwc2_readl/writel functions prototype usb: dwc3: pci: Intel Merrifield can be host usb: dwc3: pci: Supply device properties via driver data arm64: dts: dwc3: description of incr burst type usb: dwc3: Enable undefined length INCR burst type usb: dwc3: add global soc bus configuration reg0 usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci ...
2018-08-14Merge tag 'leds-for-4.19-rc1' of ↵Linus Torvalds1-21/+13
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds Pull LED updates from Jacek Anaszewski: "LED triggers improvements make the biggest part of this pull request. The most striking ones, that allowed for nice cleanups in the triggers are: - centralized handling of creation and removal of trigger sysfs attributes via attribute group - addition of module_led_trigger() helper The other things that need to be mentioned: New features and improvements to existing LED class drivers: - lt3593: add DT support, switch to gpiod interface - lm3692x: support LED sync configuration, change OF calls to fwnode calls - apu: modify PC Engines apu/apu2 driver to support apu3 Change in the drivers/net/can/led.c: - mark led trigger as broken since it's in the way for the further cleanups. It implements a subset of the netdev trigger and an Ack is needed from someone who can actually test and confirm that the netdev trigger works for can devices" * tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (32 commits) leds: ns2: Change unsigned to unsigned int usb: simplify usbport trigger leds: gpio trigger: simplifications from core changes leds: backlight trigger: simplifications from core changes leds: activity trigger: simplifications from core changes leds: default-on trigger: make use of module_led_trigger() leds: heartbeat trigger: simplifications from core changes leds: oneshot trigger: simplifications from core changes leds: transient trigger: simplifications from core changes leds: timer trigger: simplifications from core changes leds: netdev trigger: simplifications from core changes leds: triggers: new function led_set_trigger_data() leds: triggers: define module_led_trigger helper leds: triggers: handle .trigger_data and .activated() in the core leds: triggers: add device attribute support leds: triggers: let struct led_trigger::activate() return an error code leds: triggers: make the MODULE_LICENSE string match the actual license leds: lm3692x: Support LED sync configuration dt: bindings: lm3692x: Update binding for LED sync control leds: lm3692x: Change DT calls to fwnode calls ...
2018-07-30Merge 4.18-rc7 into usb-nextGreg Kroah-Hartman1-2/+6
We want the USB fixes in here as well to handle merge issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-17 16:44:38 +0300