| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit d54801cd509515f674a5aac1d3ea1401d2a05863 upstream.
ulite_probe() calls pm_runtime_put_autosuspend() at the end of probe
without holding a corresponding PM runtime reference for non-console
ports.
During ulite_assign(), uart_add_one_port() triggers uart_configure_port()
which calls ulite_pm() via uart_change_pm(). For non-console ports, the
UART core performs a balanced get/put cycle:
uart_change_pm(ON) -> ulite_pm() -> pm_runtime_get_sync() +1
uart_change_pm(OFF) -> ulite_pm() -> pm_runtime_put_autosuspend() -1
This leaves no spare reference for the pm_runtime_put_autosuspend() at
the end of probe. The PM runtime core prevents the count from actually
going below zero, and instead triggers a
"Runtime PM usage count underflow!" warning.
For console ports the bug is masked: the UART core skips the
uart_change_pm(OFF) call, so the UART core's unbalanced get happens to
pair with probe's trailing put.
Add pm_runtime_get_noresume() before pm_runtime_enable() to take an
explicit probe-owned reference that the trailing
pm_runtime_put_autosuspend() can release. This ensures a correct usage
count regardless of whether the port is a console.
Fixes: 5bbe10a6942d ("tty: serial: uartlite: Add runtime pm support")
Cc: stable <stable@kernel.org>
Signed-off-by: Maciej Andrzejewski ICEYE <maciej.andrzejewski@m-works.net>
Link: https://patch.msgid.link/20260305123746.4152800-1-maciej.andrzejewski@m-works.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e0a368ae79531ff92105a2692f10d83052055856 upstream.
When DW UART is !uart_16550_compatible, it can indicate BUSY at any
point (when under constant Rx pressure) unless a complex sequence of
steps is performed. Any LCR write can run a foul with the condition
that prevents writing LCR while the UART is BUSY, which triggers
BUSY_DETECT interrupt that seems unmaskable using IER bits.
Normal flow is that dw8250_handle_irq() handles BUSY_DETECT condition
by reading USR register. This BUSY feature, however, breaks the
assumptions made in serial8250_do_shutdown(), which runs
synchronize_irq() after clearing IER and assumes no interrupts can
occur after that point but then proceeds to update LCR, which on DW
UART can trigger an interrupt.
If serial8250_do_shutdown() releases the interrupt handler before the
handler has run and processed the BUSY_DETECT condition by read the USR
register, the IRQ is not deasserted resulting in interrupt storm that
triggers "irq x: nobody cared" warning leading to disabling the IRQ.
Add late synchronize_irq() into serial8250_do_shutdown() to ensure
BUSY_DETECT from DW UART is handled before port's interrupt handler is
released. Alternative would be to add DW UART specific shutdown
function but it would mostly duplicate the generic code and the extra
synchronize_irq() seems pretty harmless in serial8250_do_shutdown().
Fixes: 7d4008ebb1c9 ("tty: add a DesignWare 8250 driver")
Cc: stable <stable@kernel.org>
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a424a34b8faddf97b5af41689087e7a230f79ba7 upstream.
`dmaengine_terminate_async` does not guarantee that the
`__dma_tx_complete` callback will run. The callback is currently the
only place where `dma->tx_running` gets cleared. If the transaction is
canceled and the callback never runs, then `dma->tx_running` will never
get cleared and we will never schedule new TX DMA transactions again.
This change makes it so we clear `dma->tx_running` after we terminate
the DMA transaction. This is "safe" because `serial8250_tx_dma_flush`
is holding the UART port lock. The first thing the callback does is also
grab the UART port lock, so access to `dma->tx_running` is serialized.
Fixes: 9e512eaaf8f4 ("serial: 8250: Fix fifo underflow on flush")
Cc: stable <stable@kernel.org>
Signed-off-by: Raul E Rangel <rrangel@google.com>
Link: https://patch.msgid.link/20260209135815.1.I16366ecb0f62f3c96fe3dd5763fcf6f3c2b4d8cd@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c0072bc33d349c83d223e64be30794e11938a6b upstream.
This is found in popular brands such as StarTech.com or Delock, and has
been a source of frustration to quite a few people, if I can trust
Amazon comments complaining about Linux support via the official
out-of-the-tree driver.
Signed-off-by: Martin Roukala (né Peres) <martin.roukala@mupuf.org>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260309-8250_pci_ax99100-v1-1-3328bdfd8e94@mupuf.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
termination is done
[ Upstream commit a5fd8945a478ff9be14812693891d7c9b4185a50 ]
Clear rx_running flag only after DMA teardown polling completes. In the
previous implementation the flag was being cleared while hardware teardown
was still in progress, creating a mismatch between software state
(flag = 0, "ready") and hardware state (still terminating).
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-3-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 623b07b370e9963122d167e04fdc1dc713ebfbaf ]
The DMA IRQ handler does not accounts for the overrun(OE) or any other
errors being reported by the IP before triggering a DMA transaction which
leads to the interrupts not being handled resulting into an IRQ storm.
The way to handle OE is to:
1. Reset the RX FIFO.
2. Read the UART_RESUME register, which clears the internal flag
Earlier, the driver issued DMA transations even in case of OE which shouldn't
be done according to the OE handling mechanism mentioned above, as we are
resetting the FIFO's, refer section: "12.1.6.4.8.1.3.6 Overrun During
Receive" [0].
[0] https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-2-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d31228143a489ba6ba797896a07541ce06828c09 ]
Add error checking for clk_prepare_enable() calls in
dw8250_runtime_resume(). Currently if either clock fails to enable,
the function returns success while leaving clocks in inconsistent state.
This change implements comprehensive error handling by checking the return
values of both clk_prepare_enable() calls. If the second clock enable
operation fails after the first clock has already been successfully
enabled, the code now properly cleans up by disabling and unpreparing
the first clock before returning. The error code is then propagated to
the caller, ensuring that clock enable failures are properly reported
rather than being silently ignored.
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251104145433.2316165-2-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 93bb95a11238d66a4c9aa6eabf9774b073a5895c ]
Having a prompt of "DMA support" suddenly appear during a
"make oldconfig" can be confusing. Add a little helpful text to
the prompt message.
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260110232643.3533351-5-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 79527d86ba91c2d9354832d19fd12b3baa66bd10 ]
SERIAL_IMX_CONSOLE is a build option for the imx driver (SERIAL_IMX).
It does not build a separate console driver file, so it can't be built
as a module since it isn't built at all.
Change the Kconfig symbol from tristate to bool and update the help
text accordingly.
Fixes: 0db4f9b91c86 ("tty: serial: imx: enable imx serial console port as module")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-2-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 27aff0a56b3c77ea1a73641c9b3c4172a8f7238f upstream.
Fintek F81504/508/512 can support both RTS_ON_SEND and RTS_AFTER_SEND,
but pci_fintek_rs485_supported only announces the former.
This makes it impossible to unset SER_RS485_RTS_ON_SEND from
userspace because of uart_sanitize_serial_rs485(). Some devices
with these chips need RTS low on TX, so they are effectively broken.
Fix this by announcing the support for SER_RS485_RTS_AFTER_SEND,
similar to commit 068d35a7be65 ("serial: sc16is7xx: announce support
for SER_RS485_RTS_ON_SEND").
Fixes: 4afeced55baa ("serial: core: fix sanitizing check for RTS settings")
Cc: stable <stable@kernel.org>
Signed-off-by: Marnix Rijnart <marnix.rijnart@iwell.eu>
Link: https://patch.msgid.link/20260112000931.61703-1-marnix.rijnart@iwell.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6241b49540a65a6d5274fa938fd3eb4cbfe2e076 upstream.
The commit below added a new helper, but omitted to move (and add) the
corressponding kernel-doc. Do it now.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Fixes: 2b5eac0f8c6e ("tty: introduce and use tty_port_tty_vhangup() helper")
Link: https://lore.kernel.org/all/b23d566c-09dc-7374-cc87-0ad4660e8b2e@linux.intel.com/
Reported-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Link: https://lore.kernel.org/r/20250624080641.509959-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f54151148b969fb4b62bec8093d255306d20df30 upstream.
During restoring sysfs fwnode information the information of_node_reused
was dropped. This was previously set by device_set_of_node_from_dev().
Add it back manually
Fixes: 24ec03cc5512 ("serial: core: Restore sysfs fwnode information")
Cc: stable <stable@kernel.org>
Suggested-by: Cosmin Tanislav <demonsingur@gmail.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Michael Walle <mwalle@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Cosmin Tanislav <demonsingur@gmail.com>
Link: https://patch.msgid.link/20251219152813.1893982-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 267ee93c417e685d9f8e079e41c70ba6ee4df5a5 ]
RTS line control with delay should be triggered when there is no more
bytes in kfifo and hardware buffer is empty. Without this patch RTS
control is scheduled right after feeding hardware buffer and this is too
early.
RTS line may change state before hardware buffer is empty.
With this patch delayed RTS state change is triggered when function
cdns_uart_handle_tx is called from cdns_uart_isr on
CDNS_UART_IXR_TXEMPTY exactly when hardware completed transmission
Fixes: fccc9d9233f9 ("tty: serial: uartps: Add rs485 support to uartps driver")
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20251221103221.1971125-1-jakub.turek@elsta.tech
Signed-off-by: Jakub Turek <jakub.turek@elsta.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit eee00df8e1f1f5648ed8f9e40e2bb54c2877344a ]
The field 'function' of struct hrtimer should not be changed directly, as
the write is lockless and a concurrent timer expiry might end up using the
wrong function pointer.
Switch to use hrtimer_update_function() which also performs runtime checks
that it is safe to modify the callback.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/af7823518fb060c6c97105a2513cfc61adbdf38f.1738746927.git.namcao@linutronix.de
Stable-dep-of: 267ee93c417e ("serial: xilinx_uartps: fix rs485 delay_rts_after_send")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 24ec03cc55126b7b3adf102f4b3d9f716532b329 ]
The change that restores sysfs fwnode information does it only for OF cases.
Update the fix to cover all possible types of fwnodes.
Fixes: d36f0e9a0002 ("serial: core: restore of_node information in sysfs")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251127163650.2942075-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 273cc3406c8d4e830ed45967c70d08d20ca1380e ]
Make sure to drop the OF node reference taken when initialising the
control and port devices when the devices are later released.
Fixes: d36f0e9a0002 ("serial: core: restore of_node information in sysfs")
Cc: Aidan Stewart <astewart@tektelic.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250708085817.16070-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 24ec03cc5512 ("serial: core: Restore sysfs fwnode information")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2b5eac0f8c6e79bc152c8804f9f88d16717013ab ]
This code (tty_get -> vhangup -> tty_put) is repeated on few places.
Introduce a helper similar to tty_port_tty_hangup() (asynchronous) to
handle even vhangup (synchronous).
And use it on those places.
In fact, reuse the tty_port_tty_hangup()'s code and call tty_vhangup()
depending on a new bool parameter.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 74098cc06e75 ("xhci: dbgtty: fix device unregister: fixup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3ca8a0aac832fe8047608bb2ae2cca314c6d717 upstream.
The driver updates struct sci_port::tx_cookie to zero right before the TX
work is scheduled, or to -EINVAL when DMA is disabled.
dma_async_is_complete(), called through dma_cookie_status() (and possibly
through dmaengine_tx_status()), considers cookies valid only if they have
values greater than or equal to 1.
Passing zero or -EINVAL to dmaengine_tx_status() before any TX DMA
transfer has started leads to an incorrect TX status being reported, as the
cookie is invalid for the DMA subsystem. This may cause long wait times
when the serial device is opened for configuration before any TX activity
has occurred.
Check that the TX cookie is valid before passing it to
dmaengine_tx_status().
Fixes: 7cc0e0a43a91 ("serial: sh-sci: Check if TX data was written to device in .tx_empty()")
Cc: stable <stable@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20251217135759.402015-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 29e8a0c587e328ed458380a45d6028adf64d7487 ]
In sprd_clk_init(), when devm_clk_get() returns -EPROBE_DEFER
for either uart or source clock, we should propagate the
error instead of just warning and continuing with NULL clocks.
Currently the driver only emits a warning when clock acquisition
fails and proceeds with NULL clock pointers. This can lead to
issues later when the clocks are actually needed. More importantly,
when the clock provider is not ready yet and returns -EPROBE_DEFER,
we should return this error to allow deferred probing.
This change adds explicit checks for -EPROBE_DEFER after both:
1. devm_clk_get(uport->dev, uart)
2. devm_clk_get(uport->dev, source)
When -EPROBE_DEFER is encountered, the function now returns
-EPROBE_DEFER to let the driver framework retry probing
later when the clock dependencies are resolved.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Link: https://patch.msgid.link/20251022030840.956589-1-Wenhua.Lin@unisoc.com
Reviewed-by: Cixi Geng <cixi.geng@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0e5a99e0e5f50353b86939ff6e424800d769c818 upstream.
Addi-Data GmbH is manufacturing multi-serial ports cards supporting CompactPCI (known as CPCI).
Those cards are identified with different DeviceIds. Those cards integrating standard UARTs
work the same way as PCI/PCIe models already supported in the serial driver.
Signed-off-by: Magne Bruno <magne.bruno@addi-data.com>
Link: https://patch.msgid.link/20251110162456.341029-1-magne.bruno@addi-data.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb4917f557d43c7a1c805dd73ffcdfddb2aba39a upstream.
Check for returned DMA addresses using specialized dma_mapping_error()
helper which is generally recommended for this purpose by
Documentation/core-api/dma-api.rst:
"In some circumstances dma_map_single(), ...
will fail to create a mapping. A driver can check for these errors
by testing the returned DMA address with dma_mapping_error()."
Found via static analysis and this is similar to commit fa0308134d26
("ALSA: memalloc: prefer dma_mapping_error() over explicit address checking")
Fixes: 58ac1b379979 ("ARM: PL011: Fix DMA support")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://patch.msgid.link/20251027092053.87937-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Below is a patch for 6.12.58+ and 6.17.8+ stable branches only.
Upstream does not need this.
Signed-off-by: Jari Ruusu <jariruusu@protonmail.com>
Fixes: da7e8b382396 ("tty/vt: Add missing return value for VT_RESIZE in vt_ioctl()")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit da7e8b3823962b13e713d4891e136a261ed8e6a2 ]
In vt_ioctl(), the handler for VT_RESIZE always returns 0, which prevents
users from detecting errors. Add the missing return value so that errors
can be properly reported to users like vt_resizex().
Signed-off-by: Zizhi Wo <wozizhi@huaweicloud.com>
Link: https://lore.kernel.org/r/20250904023955.3892120-1-wozizhi@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 706c3c02eecd41dc675e9102b3719661cd3e30e2 ]
The dev_err_probe() doesn't do anything when error is '-ENOMEM'.
Make the following two changes:
(1) Replace -ENOMEM with -ENOSPC in max3100_probe().
(2) Just return -ENOMEM instead in max310x_probe().
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250819120927.607744-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3fc36ae6abd263a5cbf93b2f5539eccc1fc753f7 ]
After commit 84a9582fd203 ("serial: core: Start managing serial controllers
to enable runtime PM") serial drivers need to provide a device in
struct uart_port.dev otherwise an oops happens. To fix this issue
for ip22zilog driver switch driver to a platform driver and setup
the serial device in sgi-ip22 code.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20250725134018.136113-1-tsbogend@alpha.franken.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1c05bf6c0262f946571a37678250193e46b1ff0f upstream.
Commit 43c51bb573aa ("sc16is7xx: make sure device is in suspend once
probed") permanently enabled access to the enhanced features in
sc16is7xx_probe(), and it is never disabled after that.
Therefore, remove re-enable of enhanced features in
sc16is7xx_set_baud(). This eliminates a potential useless read + write
cycle each time the baud rate is reconfigured.
Fixes: 43c51bb573aa ("sc16is7xx: make sure device is in suspend once probed")
Cc: stable <stable@kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251006142002.177475-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d518314a1fa4e980a227d1b2bda1badf433cb932 upstream.
Some MediaTek SoCs got a gated UART baud clock, which currently gets
disabled as the clk subsystem believes it would be unused. This results in
the uart freezing right after "clk: Disabling unused clocks" on those
platforms.
Request the baud clock to be prepared and enabled during probe, and to
restore run-time power management capabilities to what it was before commit
e32a83c70cf9 ("serial: 8250-mtk: modify mtk uart power and clock
management") disable and unprepare the baud clock when suspending the UART,
prepare and enable it again when resuming it.
Fixes: e32a83c70cf9 ("serial: 8250-mtk: modify mtk uart power and clock management")
Fixes: b6c7ff2693ddc ("serial: 8250_mtk: Simplify clock sequencing and runtime PM")
Cc: stable <stable@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/de5197ccc31e1dab0965cabcc11ca92e67246cf6.1758058441.git.daniel@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7cbce761fe3fcbcb49bcf30d4f8ca5e1a9ee2a0 upstream.
The Advantech 2-port serial card with PCI vendor=0x13fe and device=0x0018
has a 'XR17V35X' chip installed on the circuit board. Therefore, this
driver can be used instead of theu outdated out-of-tree driver from the
manufacturer.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20250924134115.2667650-1-fe@dev.tdt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit daeb4037adf7d3349b4a1fb792f4bc9824686a4b upstream.
Check the return value of reset_control_deassert() in the probe
function to prevent continuing probe when reset deassertion fails.
Previously, reset_control_deassert() was called without checking its
return value, which could lead to probe continuing even when the
device reset wasn't properly deasserted.
The fix checks the return value and returns an error with dev_err_probe()
if reset deassertion fails, providing better error handling and
diagnostics.
Fixes: acbdad8dd1ab ("serial: 8250_dw: simplify optional reset handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251019095131.252848-1-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3cf0b3c243e56bc43be560617416c1d9f301f44c ]
Currently gsm_queue() processes incoming frames and when opening
a DLC channel it calls gsm_dlci_open() which calls gsm_modem_update().
If basic mode is used it calls gsm_modem_upd_via_msc() and it
cannot block the input queue by waiting the response to come
into the same input queue.
Instead allow sending Modem Status Command without waiting for remote
end to respond. Define a new function gsm_modem_send_initial_msc()
for this purpose. As MSC is only valid for basic encoding, it does
not do anything for advanced or when convergence layer type 2 is used.
Fixes: 48473802506d ("tty: n_gsm: fix missing update of modem controls after DLCI open")
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Link: https://lore.kernel.org/r/20250827123221.1148666-1-seppo.takalo@nordicsemi.no
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 672a37ba8af1f2ebcedeb94aea2cdd047f805f30 ]
Check if devm_i2c_new_dummy_device() fails.
Fixes: 2e1f2d9a9bdb ("serial: max310x: implement I2C support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/aJTMPZiKqeXSE-KM@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit cc4d900d0d6d8dd5c41832a93ff3cfa629a78f9a upstream.
Console can be enabled on the UART compile as module.
Change dependency to allow console mode when the driver is built as module.
Fixes: 48a6092fb41fa ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Link: https://lore.kernel.org/r/20250822141923.61133-1-raphael.gallais-pou@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 535fd4c98452c87537a40610abba45daf5761ec6 upstream.
When trying to set MCR[2], XON1 is incorrectly accessed instead. And when
writing to the TCR register to configure flow control levels, we are
incorrectly writing to the MSR register. The default value of $00 is then
used for TCR, which means that selectable trigger levels in FCR are used
in place of TCR.
TCR/TLR access requires EFR[4] (enable enhanced functions) and MCR[2]
to be set. EFR[4] is already set in probe().
MCR access requires LCR[7] to be zero.
Since LCR is set to $BF when trying to set MCR[2], XON1 is incorrectly
accessed instead because MCR shares the same address space as XON1.
Since MCR[2] is unmodified and still zero, when writing to TCR we are in
fact writing to MSR because TCR/TLR registers share the same address space
as MSR/SPR.
Fix by first removing useless reconfiguration of EFR[4] (enable enhanced
functions), as it is already enabled in sc16is7xx_probe() since commit
43c51bb573aa ("sc16is7xx: make sure device is in suspend once probed").
Now LCR is $00, which means that MCR access is enabled.
Also remove regcache_cache_bypass() calls since we no longer access the
enhanced registers set, and TCR is already declared as volatile (in fact
by declaring MSR as volatile, which shares the same address).
Finally disable access to TCR/TLR registers after modifying them by
clearing MCR[2].
Note: the comment about "... and internal clock div" is wrong and can be
ignored/removed as access to internal clock div registers (DLL/DLH)
is permitted only when LCR[7] is logic 1, not when enhanced features
is enabled. And DLL/DLH access is not needed in sc16is7xx_startup().
Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20250731124451.1108864-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cfd956dcb101aa3d25bac321fae923323a47c607 upstream.
After hvc_write completes, call hvc_kick also in the case the output
buffer has been drained, to ensure tty_wakeup gets called.
This fixes that functions which wait for a drained buffer got stuck
occasionally.
Cc: stable <stable@kernel.org>
Closes: https://bugzilla.opensuse.org/show_bug.cgi?id=1230062
Signed-off-by: Fabian Vogt <fvogt@suse.de>
Link: https://lore.kernel.org/r/2011735.PYKUYFuaPT@fvogt-thinkpad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b43cb4ff85da5cf29c4cd351ef1d7dd8210780f7 upstream.
The maximum number of keycodes got bumped to 256 a very long time ago,
but the default keymaps were never adjusted to match. This is causing
the kernel to interpret keycodes above 127 as U+0000 if the shipped
generated keymap is used.
Fix this by mapping all keycodes above 127 to K_HOLE so the kernel
ignores them.
The contents of this patche were generated by rerunning `loadkeys
--mktable --unicode` and only including the changes to map keycodes
above 127 to K_HOLE.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250702-vt-misc-unicode-fixes-v1-2-c27e143cc2eb@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1cc2092ea7a52e2c435aee6d2b1bcb773202663 upstream.
We don't process Unicode characters if the virtual terminal is in raw
mode, so there's no reason why we shouldn't do the same for K_OFF
(especially since people would expect K_OFF to actually turn off all VT
key processing).
Fixes: 9fc3de9c8356 ("vt: Add virtual console keyboard mode OFF")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250702-vt-misc-unicode-fixes-v1-1-c27e143cc2eb@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f8fdd4dbffc05982b96caf586f77a014b2a9353 upstream.
When the PSLVERR_RESP_EN parameter is set to 1, the device generates
an error response if an attempt is made to read an empty RBR (Receive
Buffer Register) while the FIFO is enabled.
In serial8250_do_startup(), calling serial_port_out(port, UART_LCR,
UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes
dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter
function enables the FIFO via serial_out(p, UART_FCR, p->fcr).
Execution proceeds to the serial_port_in(port, UART_RX).
This satisfies the PSLVERR trigger condition.
When another CPU (e.g., using printk()) is accessing the UART (UART
is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) ==
(lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter
dw8250_force_idle().
Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock
to fix this issue.
Panic backtrace:
[ 0.442336] Oops - unknown exception [#1]
[ 0.442343] epc : dw8250_serial_in32+0x1e/0x4a
[ 0.442351] ra : serial8250_do_startup+0x2c8/0x88e
...
[ 0.442416] console_on_rootfs+0x26/0x70
Fixes: c49436b657d0 ("serial: 8250_dw: Improve unwritable LCR workaround")
Link: https://lore.kernel.org/all/84cydt5peu.fsf@jogness.linutronix.de/T/
Signed-off-by: Yunhui Cui <cuiyunhui@bytedance.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250723023322.464-2-cuiyunhui@bytedance.com
[ adapted to inline code structure without separate serial8250_initialize helper function ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 33a2515abd45c64911955ff1da179589db54f99f ]
The serial info sometimes produces negative TX/RX counts. E.g.:
3: uart:FSL_LPUART mmio:0x02970000 irq:46 tx:-1595870545 rx:339619
RTS|CTS|DTR|DSR|CD
It appears that the print format specifiers don't match with the types of
the respective variables. E.g.: All of the fields in struct uart_icount
are u32, but the format specifier used is %d, even though u32 is unsigned
and %d is for signed integers. Update drivers/tty/serial/serial_core.c
to use the proper format specifiers. Reference
https://docs.kernel.org/core-api/printk-formats.html as the documentation
for what format specifiers are the proper ones to use for a given C type.
Signed-off-by: Joseph Tilahun <jtilahun@astranis.com>
Link: https://lore.kernel.org/r/20250610065653.3750067-1-jtilahun@astranis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6c0e9f05c9d7875995b0e92ace71be947f280bbd upstream.
The dma_sync_sg_for_device() functions should be called with the same
nents as the dma_map_sg(), not the value the map function returned
according to the documentation in Documentation/core-api/dma-api.rst:450:
With the sync_sg API, all the parameters must be the same
as those passed into the sg mapping API.
Fixes: da3564ee027e ("pch_uart: add multi-scatter processing")
Cc: stable <stable@kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250701113452.18590-2-fourier.thomas@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ff78538e07fa284ce08cbbcb0730daa91ed16722 ]
Programs using poll() on /dev/vcsa to be notified when VT changes occur
were missing one case: the switch from gfx to text mode.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/9o5ro928-0pp4-05rq-70p4-ro385n21n723@onlyvoer.pbz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f23c52aafb1675ab1d1f46914556d8e29cbbf7b3 upstream.
Commit 7a637784d517 ("serial: imx: reduce RX interrupt frequency")
introduced a regression on the i.MX6UL EVK board. The issue can be
reproduced with the following steps:
- Open vi on the board.
- Paste a text file (~150 characters).
- Save the file, then repeat the process.
- Compare the sha256sum of the saved files.
The checksums do not match due to missing characters or entire lines.
Fix this by restoring the RXTL value to 1 when the UART is used as a
console.
This ensures timely RX interrupts and reliable data reception in console
mode.
With this change, pasted content is saved correctly, and checksums are
always consistent.
Cc: stable <stable@kernel.org>
Fixes: 7a637784d517 ("serial: imx: reduce RX interrupt frequency")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250619114617.2791939-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d36f0e9a0002f04f4d6dd9be908d58fe5bd3a279 upstream.
Since in v6.8-rc1, the of_node symlink under tty devices is
missing. This breaks any udev rules relying on this information.
Link the of_node information in the serial controller device with the
parent defined in the device tree. This will also apply to the serial
device which takes the serial controller as a parent device.
Fixes: b286f4e87e32 ("serial: core: Move tty and serdev to be children of serial core port device")
Cc: stable@vger.kernel.org
Signed-off-by: Aidan Stewart <astewart@tektelic.com>
Link: https://lore.kernel.org/r/20250617164819.13912-1-astewart@tektelic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6bd697b5fc39fd24e2aa418c7b7d14469f550a93 ]
When two instances of uart devices are probing, a concurrency race can
occur. If one thread calls uart_register_driver function, which first
allocates and assigns memory to 'uart_state' member of uart_driver
structure, the other instance can bypass uart driver registration and
call ulite_assign. This calls uart_add_one_port, which expects the uart
driver to be fully initialized. This leads to a kernel panic due to a
null pointer dereference:
[ 8.143581] BUG: kernel NULL pointer dereference, address: 00000000000002b8
[ 8.156982] #PF: supervisor write access in kernel mode
[ 8.156984] #PF: error_code(0x0002) - not-present page
[ 8.156986] PGD 0 P4D 0
...
[ 8.180668] RIP: 0010:mutex_lock+0x19/0x30
[ 8.188624] Call Trace:
[ 8.188629] ? __die_body.cold+0x1a/0x1f
[ 8.195260] ? page_fault_oops+0x15c/0x290
[ 8.209183] ? __irq_resolve_mapping+0x47/0x80
[ 8.209187] ? exc_page_fault+0x64/0x140
[ 8.209190] ? asm_exc_page_fault+0x22/0x30
[ 8.209196] ? mutex_lock+0x19/0x30
[ 8.223116] uart_add_one_port+0x60/0x440
[ 8.223122] ? proc_tty_register_driver+0x43/0x50
[ 8.223126] ? tty_register_driver+0x1ca/0x1e0
[ 8.246250] ulite_probe+0x357/0x4b0 [uartlite]
To prevent it, move uart driver registration in to init function. This
will ensure that uart_driver is always registered when probe function
is called.
Signed-off-by: Jakub Lewalski <jakub.lewalski@nokia.com>
Signed-off-by: Elodie Decerle <elodie.decerle@nokia.com>
Link: https://lore.kernel.org/r/20250331160732.2042-1-elodie.decerle@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
later devices
[ Upstream commit c40b91e38eb8d4489def095d62ab476d45871323 ]
Systems that issue PCIe hot reset requests during a suspend/resume
cycle cause PCI1XXXX device revisions prior to C0 to get its UART
configuration registers reset to hardware default values. This results
in device inaccessibility and data transfer failures. Starting with
Revision C0, support was added in the device hardware (via the Hot
Reset Disable Bit) to allow resetting only the PCIe interface and its
associated logic, but preserving the UART configuration during a hot
reset. This patch enables the hot reset disable feature during suspend/
resume for C0 and later revisions of the device.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425145500.29036-1-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 651dee03696e1dfde6d9a7e8664bbdcd9a10ea7f upstream.
In the sh-sci driver, serial ports are mapped to the sci_ports[] array,
with earlycon mapped at index zero.
The uart_add_one_port() function eventually calls __device_attach(),
which, in turn, calls pm_request_idle(). The identified code path is as
follows:
uart_add_one_port() ->
serial_ctrl_register_port() ->
serial_core_register_port() ->
serial_core_port_device_add() ->
serial_base_port_add() ->
device_add() ->
bus_probe_device() ->
device_initial_probe() ->
__device_attach() ->
// ...
if (dev->p->dead) {
// ...
} else if (dev->driver) {
// ...
} else {
// ...
pm_request_idle(dev);
// ...
}
The earlycon device clocks are enabled by the bootloader. However, the
pm_request_idle() call in __device_attach() disables the SCI port clocks
while earlycon is still active.
The earlycon write function, serial_console_write(), calls
sci_poll_put_char() via serial_console_putchar(). If the SCI port clocks
are disabled, writing to earlycon may sometimes cause the SR.TDFE bit to
remain unset indefinitely, causing the while loop in sci_poll_put_char()
to never exit. On single-core SoCs, this can result in the system being
blocked during boot when this issue occurs.
To resolve this, increment the runtime PM usage counter for the earlycon
SCI device before registering the UART port.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f1017069933489add0c08659673443c9905659e upstream.
The early_console_setup() function initializes sci_ports[0].port with an
object of type struct uart_port obtained from the struct earlycon_device
passed as an argument to early_console_setup().
Later, during serial port probing, the serial port used as earlycon
(e.g., port A) might be remapped to a different position in the sci_ports[]
array, and a different serial port (e.g., port B) might be assigned to slot
0. For example:
sci_ports[0] = port B
sci_ports[X] = port A
In this scenario, the new port mapped at index zero (port B) retains the
data associated with the earlycon configuration. Consequently, after the
Linux boot process, any access to the serial port now mapped to
sci_ports[0] (port B) will block the original earlycon port (port A).
To address this, introduce an early_console_exit() function to clean up
sci_ports[0] when earlycon is exited.
To prevent the cleanup of sci_ports[0] while the serial device is still
being used by earlycon, introduce the struct sci_port::probing flag and
account for it in early_console_exit().
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b495021a973e2468497689bd3e29b736747b896f upstream.
Commit 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
introduced an error in the TX DMA handling for 8250_omap.
When the OMAP_DMA_TX_KICK flag is set, the "skip_byte" is pulled from
the kfifo and emitted directly in order to start the DMA. While the
kfifo is updated, dma->tx_size is not decreased. This leads to
uart_xmit_advance() called in omap_8250_dma_tx_complete() advancing the
kfifo by one too much.
In practice, transmitting N bytes has been seen to result in the last
N-1 bytes being sent repeatedly.
This change fixes the problem by moving all of the dma setup after the
OMAP_DMA_TX_KICK handling and using kfifo_len() instead of the DMA size
for the 4-byte cutoff check. This slightly changes the behaviour at
buffer wraparound, but it still transmits the correct bytes somehow.
Now, the "skip_byte" would no longer be accounted to the stats. As
previously, dma->tx_size included also this skip byte, up->icount.tx was
updated by aforementioned uart_xmit_advance() in
omap_8250_dma_tx_complete(). Fix this by using the uart_fifo_out()
helper instead of bare kfifo_get().
Based on patch by Mans Rullgard <mans@mansr.com>
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Fixes: 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
Link: https://lore.kernel.org/all/20250506150748.3162-1-mans@mansr.com/
Reported-by: Mans Rullgard <mans@mansr.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250522053835.3495975-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 239f11209e5f282e16f5241b99256e25dd0614b6 ]
Relocate the runtime PM enable operation to sci_probe_single(). This change
prepares the codebase for upcoming fixes.
While at it, replace the existing logic with a direct call to
devm_pm_runtime_enable() and remove sci_cleanup_single(). The
devm_pm_runtime_enable() function automatically handles disabling runtime
PM during driver removal.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c4c7ead7b86c1e7f11c64915b7e5bb6d2e242691 ]
They are listed amon those cmd values that "treat 'arg' as an integer"
which is wrong. They should instead fall into the default case. Probably
nobody ever relied on that code since 2009 but still.
Fixes: e92166517e3c ("tty: handle VT specific compat ioctls in vt driver")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/pr214s15-36r8-6732-2pop-159nq85o48r7@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 86bcae88c9209e334b2f8c252f4cc66beb261886 ]
devm_ioremap() can return NULL on error. Currently, mlb_usio_probe()
does not check for this case, which could result in a NULL pointer
dereference.
Add NULL check after devm_ioremap() to prevent this issue.
Fixes: ba44dc043004 ("serial: Add Milbeaut serial control")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Link: https://lore.kernel.org/r/20250403070339.64990-1-bsdhenrymartin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
