| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit b1b4efea05a56c0995e4702a86d6624b4fdff32f ]
In accordance with Errata (specification updates)
HSUART May Stop Functioning when DMA is Active.
- Denverton document #572409, rev 3.4, DNV60
- Ice Lake Xeon D document #714070, ICXD65
- Snowridge document #731931, SNR44
For a quick fix just disable the respective callbacks during the device probe.
Depending on the future development we might remove them completely.
Reported-by: micas-opensource <zjianan156@gmail.com>
Closes: https://lore.kernel.org/linux-serial/20250625031409.2404219-1-opensource@ruijie.com.cn/
Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260626094937.561776-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a136abd7e7abe0f1247f8ffde6cc7c8ab09f985b ]
8250_mid uses FL_*BASE* from linux/8250_pci.h and nothing else. The
code can be simplified by directly defining BARs within the driver
instead.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230915094336.13278-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b1b4efea05a5 ("serial: 8250_mid: Disable DMA for selected platforms")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 061b627ba534230a18ec4d7251562af12325d06a upstream.
On AM33xx RX DMA only triggers when the FIFO reaches the
configured threshold (typically 48 bytes). For smaller bursts
no DMA request is issued and the FIFO is drained by RX timeout.
In this case __dma_rx_do_complete() can legitimately see count == 0.
The current code exits early in this case and does not clear
dma->rx_running, leaving the DMA state inconsistent. This can
prevent RX DMA from restarting and may cause
omap_8250_rx_dma_flush() to fail, marking DMA as broken.
Fix this by clearing dma->rx_running once the DMA transfer has
completed or been terminated, even if no data was transferred.
Fixes: a5fd8945a478 ("serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done")
Cc: stable <stable@kernel.org>
Signed-off-by: Matthias Feser <mfe@KBSgmbhfr.onmicrosoft.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/BE3P281MB55155F2F5795E411F5A65282EE0B2@BE3P281MB5515.DEUP281.PROD.OUTLOOK.COM
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 22dd2777e6c180e1c945b00f6d18550979436324 upstream.
At the moment, concurrent writes from userspace and the kernel to the
console can trigger a race condition that results in an infinite loop of
the same messages printed over and over again. This is most likely to
happen during system startup or shutdown when the init system starts/stops
a large number of system services that interact with various kernel code.
When userspace writes to the TTY device, the driver initiates an
asynchronous DMA transfer and releases the port lock. At the same moment,
the kernel printk path might grab the port lock and re-configure the UART
controller for PIO, without waiting for the DMA operation to complete. It
seems like this collision results in zero progress being reported for the
DMA engine, so the same text is printed to the console over and over again.
For the kernel console, we want a reliable output path that will be
functional even during crashes etc. So rather than implementing complex
code to synchronize the kernel console write routines with the userspace
DMA write routines, simply disable DMA for the console UART instance.
Similar checks exist in many other serial drivers, e.g. 8250_port.c,
imx.c, sh-sci.c etc.
Cc: stable <stable@kernel.org>
Fixes: 3a878c430fd6 ("tty: serial: msm: Add TX DMA support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260706-serial-msm-console-dma-collision-v1-1-3179b8cb1d89@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a287620312dc6dcb9a093417a0e589bf30fcf38a upstream.
A KASAN null-ptr-deref was observed in vcs_notifier():
BUG: KASAN: null-ptr-deref in vcs_notifier+0x98/0x130
Read of size 2 at addr qmp_cmd_name: qmp_capabilities, arguments: {}
The issue is a race condition in vcs_write(). When the console_lock is
temporarily dropped (to copy data from userspace), the vc_data pointer
obtained from vcs_vc() may become stale. After re-acquiring the lock,
vcs_vc() is called again to re-validate the pointer. If the vc has been
deallocated in the meantime, vcs_vc() returns NULL, and the while loop
breaks (with written > 0). However, after the loop, vcs_scr_updated(vc)
is still called with the now-NULL vc pointer, leading to a null pointer
dereference in the notifier chain (vcs_notifier dereferences param->vc).
Fix this by adding a NULL check for vc before calling vcs_scr_updated().
Fixes: 8fb9ea65c9d1 ("vc_screen: reload load of struct vc_data pointer in vcs_write() to avoid UAF")
Cc: stable@vger.kernel.org
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20260604060734.2914976-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a3bb136bff5e6a5e48cdd813246c9c4686feaaa9 ]
Sashiko identified a deadlock when the console flow is engaged [1].
When console flow control is enabled (UPF_CONS_FLOW),
s3c24xx_serial_stop_tx() calls s3c24xx_serial_rx_enable() and
s3c24xx_serial_start_tx() calls s3c24xx_serial_rx_disable().
The serial core framework invokes the .stop_tx() and .start_tx()
callbacks with the port->lock spinlock already held. Furthermore, all
internal driver paths that invoke stop_tx (such as the DMA TX
completion handler s3c24xx_serial_tx_dma_complete() or the PIO TX IRQ
handler s3c24xx_serial_tx_irq()) also acquire port->lock prior to
calling it. (Note that s3c24xx_serial_start_tx() is only invoked by the
serial core).
However, s3c24xx_serial_rx_enable() and s3c24xx_serial_rx_disable()
unconditionally attempt to acquire port->lock again using
uart_port_lock_irqsave(). Since spinlocks are not recursive, this
causes a deadlock on the same CPU when console flow control is engaged.
Remove the redundant lock acquisition from both rx helper functions.
Cc: stable <stable@kernel.org>
Fixes: b497549a035c ("[ARM] S3C24XX: Split serial driver into core and per-cpu drivers")
Reported-by: John Ogness <john.ogness@linutronix.de>
Closes: https://sashiko.dev/#/patchset/20260506121606.5805-1-john.ogness%40linutronix.de [1]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20260515-samsung-tty-flow-control-deadlock-v1-1-93255edbc9bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 032a725c16add79332d774348d7ad7d0d4b86479 ]
All registers of the IP have 32 bits. Use u32 variables when reading
or writing from/to the registers. The purpose of those variables becomes
clearer.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-9-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a3bb136bff5e ("tty: serial: samsung: Remove redundant port lock acquisition in rx helpers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 97d7a9aeba1d424c2359f1686d02c75d798ad184 ]
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-54-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a3bb136bff5e ("tty: serial: samsung: Remove redundant port lock acquisition in rx helpers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ea66be25f0e934f49d24cd0c5845d13cdba3520b ]
altera_jtaguart_probe() maps the register window before registering the
UART port, but it ignores failures from uart_add_one_port(). If port
registration fails, probe still returns success and the mapping remains
live until a later remove path that is not part of probe failure cleanup.
Return the uart_add_one_port() error and unmap the register window on
that failure path.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: 5bcd601049c6 ("serial: Add driver for the Altera JTAG UART")
Cc: stable <stable@kernel.org>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Link: https://patch.msgid.link/20260512065837.79528-1-mhun512@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 60302276caff50f907bc3391a364691ab4a21b43 ]
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ea66be25f0e9 ("serial: altera_jtaguart: handle uart_add_one_port() failures")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ca2584d841b69391ffc4144840563d2e1a0018df ]
UART_RX_PAR_EN is incorrectly defined as bit 3, which triggers false
framing errors (S_GP_IRQ_1_EN) and causes received data to be dropped
when parity is enabled and the parity bit is 0.
Define UART_RX_PAR_EN as bit 4 of the SE_UART_RX_TRANS_CFG register, as
specified in the reference manual.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable <stable@kernel.org>
Signed-off-by: Prasanna S <prasanna.s@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260428-serial-bit-correct-v1-1-9131ad5b97d8@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6cde11dbf4b65170eeefba48df730c93d75e01a3 ]
Keep the #define symbols aligned for better readability.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-5-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ca2584d841b6 ("serial: qcom-geni: fix UART_RX_PAR_EN bit position")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 68c6bd92c86cbc4937834c79963b27c77ee3bf51 ]
Drop all unused symbols from the driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-4-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ca2584d841b6 ("serial: qcom-geni: fix UART_RX_PAR_EN bit position")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f127b2208e5e2b817243cad41fe4211a6d5a7a3 upstream.
Calling dz_reset() in the course of setting up the serial device causes
line parameters to be reset and the transmitter disabled. We've been
lucky in that no message is usually produced to the kernel log between
this call and the later call to uart_set_options() in the course of
console setup done by dz_serial_console_init(), or the system would hang
as the console output handler in the firmware tried to access a port the
transmitter of which has been disabled and line parameters messed up.
This will change with the next change to the driver, so fix dz_reset()
such that line parameters are set for 9600n8 console operation as with
the system firmware and the transmitter re-enabled after reset. This
also means dz_pm() serves no purpose anymore, so drop it.
Fixes: e6ee512f5a77 ("dz.c: Resource management")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.25+
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062302010.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Avoid C99+ 'for' loop initial declaration for 5.10.y. ]
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8572955630f30948837088aa98bcbe0532d1ceac upstream.
Switch the driver to using the channel reset rather than hardware reset,
simplifying handling by removing an interference between channels that
causes the other channel to become uninitialised afterwards.
There is little difference between the two kinds of reset in terms of
register settings that result, and we initialise the whole register set
right away anyway. However this prevents a hang from happening should
the console output handler in the firmware try to access the other port
whose transmitter has been disabled and line parameters messed up.
For example this will happen if the keyboard port (port A) is chosen for
the system console, unusually but not insanely for a headless system, as
the port is wired to a standard DA-15 connector and an adapter can be
easily made. Or with the next change in place this would happen for the
regular console port (port B), since the keyboard port (port A) will be
initialised first.
Just remove the unnecessary complication then, a channel reset is good
enough. We still need the initialisation marker, now per channel rather
than per SCC, as for the console port zs_reset() will be called twice:
once early on via zs_serial_console_init() for the console setup only,
and then again via zs_config_port() as the port is associated with a TTY
device.
Fixes: 8b4a40809e53 ("zs: move to the serial subsystem")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.23+
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062323430.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c05cf72e13314ce9b770b5951695dc5a2152920 upstream.
Calling zs_reset() in the course of setting up the serial device causes
line parameters to be reset and the transmitter disabled. We've been
lucky in that no message is usually produced to the kernel log between
this call and the later call to uart_set_options() in the course of
console setup done by zs_serial_console_init(), or the system would hang
as the console output handler in the firmware tried to access a port the
transmitter of which has been disabled and line parameters messed up.
This will change with the next change to the driver, so fix zs_reset()
such that line parameters are set for 9600n8 console operation as with
the system firmware and the transmitter re-enabled after reset. This
also means zs_pm() serves no purpose anymore, so drop it.
Fixes: 8b4a40809e53 ("zs: move to the serial subsystem")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.23+
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062308040.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca904f4b42355287bc5ce8b7550ebe909cda4c2c upstream.
In the DZ interface as implemented by the DC7085 gate array the serial
transmitters are double buffered, meaning that at the time a transmitter
is ready to accept the next character there is one in the transmit shift
register still being sent to the line. Issuing a master clear at this
time causes this character to be lost, so wait an extra amount of time
sufficient for the transmit shift register to drain at 9600bps, which is
the baud rate setting used by the firmware console.
Mind the specified 1.4us TRDY recovery time in the course and continue
using iob() as the completion barrier, since the platforms involved use
a write buffer that can delay and combine writes, and reorder them with
respect to reads regardless of the MMIO locations accessed and we still
lack a platform-independent handler for that.
When called from dz_serial_console_init() this is too early for fsleep()
to work and even before lpj has been calculated and therefore the delay
is actually not sufficient for the transmitter to drain and is merely a
placeholder now. This will be addressed in a follow-up change.
Fixes: e6ee512f5a77 ("dz.c: Resource management")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.25+
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062259080.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a9254c4a2a3ca2b3da16d173f3b0dd01f397ff6 upstream.
lpuart_start_rx_dma() allocates sport->rx_ring.buf with kzalloc() and
then maps a scatterlist via dma_map_sg(). On three subsequent error
paths the function returns directly without releasing those resources:
- when dma_map_sg() returns 0 (-EINVAL):
ring->buf is leaked.
- when dmaengine_slave_config() fails:
ring->buf and the DMA mapping are leaked.
- when dmaengine_prep_dma_cyclic() returns NULL:
ring->buf and the DMA mapping are leaked.
The sole cleanup path, lpuart_dma_rx_free(), is only reached when
lpuart_dma_rx_use is set, and the caller lpuart_rx_dma_startup() clears
that flag on failure of lpuart_start_rx_dma(). So these resources are
permanently leaked on every failure in this function. Repeated port
open/close or termios changes under error conditions will slowly consume
memory and leave stale streaming DMA mappings behind.
Fix it by introducing two error labels that unmap the scatterlist and
free the ring buffer as appropriate. While here, replace the misleading
-EFAULT (bad userspace pointer) returned when dmaengine_prep_dma_cyclic()
fails with the more accurate -ENOMEM, matching how other dmaengine users
in the tree treat this failure.
No functional change on the success path.
Fixes: 5887ad43ee02 ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Cc: stable <stable@kernel.org>
Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260420135903.2062024-1-shitalkumar.gandhi@cambiumnetworks.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d15cd40cb1858f75846eaafa9a6bca841b790a92 upstream.
Fix a thinko in the status interrupt handler that has caused counters
for the RI and DSR modem line transitions to be used for the other line
each.
Fixes: 8b4a40809e53 ("zs: move to the serial subsystem")
Cc: stable <stable@kernel.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://patch.msgid.link/alpine.DEB.2.21.2604101747110.29980@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 92b1ea22454b08a39baef3a7290fb3ec50366616 upstream.
The sci_request_port() function uses request_mem_region() to reserve
I/O memory, but in the error path when sci_remap_port() fails, it
incorrectly calls release_resource() instead of release_mem_region().
This mismatch can cause resource accounting issues. Fix it by using
the correct release function, consistent with sci_release_port().
Fixes: e2651647080930a1 ("serial: sh-sci: Handle port memory region reservations.")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202604032356.SzEjYkBC-lkp@intel.com/
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260421065737.724187-1-zenghongling@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fe472c1bbbe238e91141f7cabc1226e96a60d43 upstream.
Add a check for dma_alloc_coherent() failure to prevent a potential
NULL pointer dereference in dma_handle_rx(). Properly release DMA
channels and the PCI device reference using a goto ladder if the
allocation fails.
Fixes: 3c6a483275f4 ("Serial: EG20T: add PCH_UART driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Zhaoyang Yu <2426767509@qq.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/tencent_E328416B7CFD436F6029F2DF02AD7ED89C08@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f2a880e802ad12d1e38039d1334fb1475d0f5241 ]
MAX_HVC_IUCV_LINES == HVC_ALLOC_TTY_ADAPTERS == 8.
This is the number of entries in:
static struct hvc_iucv_private *hvc_iucv_table[MAX_HVC_IUCV_LINES];
Sometimes hvc_iucv_table[] is limited by:
(a) if (num > hvc_iucv_devices) // for error detection
or
(b) for (i = 0; i < hvc_iucv_devices; i++) // in 2 places
(so these 2 don't agree; second one appears to be correct to me.)
hvc_iucv_devices can be 0..8. This is a counter.
(c) if (hvc_iucv_devices > MAX_HVC_IUCV_LINES)
If hvc_iucv_devices == 8, (a) allows the code to access hvc_iucv_table[8].
Oops.
Fixes: 44a01d5ba8a4 ("[S390] s390/hvc_console: z/VM IUCV hypervisor console support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260130072939.1535869-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eef7381d8134f249dc17138bb1794c249aff7f5a ]
According to Greg, in the context of magic numbers as defined in
magic-number.rst, "the tty layer should not need this and I'll gladly
take patches"
This stretches that definition slightly, since it multiplexes it with
the terminal number as a constant offset, but is equivalent
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Ref: https://lore.kernel.org/linux-doc/YyMlovoskUcHLEb7@kroah.com/
Link: https://lore.kernel.org/r/8c8a2c9dfc1bfbe6ef3f3237368e483865fc1c29.1663288066.git.nabijaczleweli@nabijaczleweli.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f2a880e802ad ("tty: hvc_iucv: fix off-by-one in number of supported devices")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e0a368ae79531ff92105a2692f10d83052055856 upstream.
When DW UART is !uart_16550_compatible, it can indicate BUSY at any
point (when under constant Rx pressure) unless a complex sequence of
steps is performed. Any LCR write can run a foul with the condition
that prevents writing LCR while the UART is BUSY, which triggers
BUSY_DETECT interrupt that seems unmaskable using IER bits.
Normal flow is that dw8250_handle_irq() handles BUSY_DETECT condition
by reading USR register. This BUSY feature, however, breaks the
assumptions made in serial8250_do_shutdown(), which runs
synchronize_irq() after clearing IER and assumes no interrupts can
occur after that point but then proceeds to update LCR, which on DW
UART can trigger an interrupt.
If serial8250_do_shutdown() releases the interrupt handler before the
handler has run and processed the BUSY_DETECT condition by read the USR
register, the IRQ is not deasserted resulting in interrupt storm that
triggers "irq x: nobody cared" warning leading to disabling the IRQ.
Add late synchronize_irq() into serial8250_do_shutdown() to ensure
BUSY_DETECT from DW UART is handled before port's interrupt handler is
released. Alternative would be to add DW UART specific shutdown
function but it would mostly duplicate the generic code and the extra
synchronize_irq() seems pretty harmless in serial8250_do_shutdown().
Fixes: 7d4008ebb1c9 ("tty: add a DesignWare 8250 driver")
Cc: stable <stable@kernel.org>
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a424a34b8faddf97b5af41689087e7a230f79ba7 upstream.
`dmaengine_terminate_async` does not guarantee that the
`__dma_tx_complete` callback will run. The callback is currently the
only place where `dma->tx_running` gets cleared. If the transaction is
canceled and the callback never runs, then `dma->tx_running` will never
get cleared and we will never schedule new TX DMA transactions again.
This change makes it so we clear `dma->tx_running` after we terminate
the DMA transaction. This is "safe" because `serial8250_tx_dma_flush`
is holding the UART port lock. The first thing the callback does is also
grab the UART port lock, so access to `dma->tx_running` is serialized.
Fixes: 9e512eaaf8f4 ("serial: 8250: Fix fifo underflow on flush")
Cc: stable <stable@kernel.org>
Signed-off-by: Raul E Rangel <rrangel@google.com>
Link: https://patch.msgid.link/20260209135815.1.I16366ecb0f62f3c96fe3dd5763fcf6f3c2b4d8cd@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c0072bc33d349c83d223e64be30794e11938a6b upstream.
This is found in popular brands such as StarTech.com or Delock, and has
been a source of frustration to quite a few people, if I can trust
Amazon comments complaining about Linux support via the official
out-of-the-tree driver.
Signed-off-by: Martin Roukala (né Peres) <martin.roukala@mupuf.org>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260309-8250_pci_ax99100-v1-1-3328bdfd8e94@mupuf.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
termination is done
[ Upstream commit a5fd8945a478ff9be14812693891d7c9b4185a50 ]
Clear rx_running flag only after DMA teardown polling completes. In the
previous implementation the flag was being cleared while hardware teardown
was still in progress, creating a mismatch between software state
(flag = 0, "ready") and hardware state (still terminating).
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-3-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d31228143a489ba6ba797896a07541ce06828c09 ]
Add error checking for clk_prepare_enable() calls in
dw8250_runtime_resume(). Currently if either clock fails to enable,
the function returns success while leaving clocks in inconsistent state.
This change implements comprehensive error handling by checking the return
values of both clk_prepare_enable() calls. If the second clock enable
operation fails after the first clock has already been successfully
enabled, the code now properly cleans up by disabling and unpreparing
the first clock before returning. The error code is then propagated to
the caller, ensuring that clock enable failures are properly reported
rather than being silently ignored.
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251104145433.2316165-2-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 93bb95a11238d66a4c9aa6eabf9774b073a5895c ]
Having a prompt of "DMA support" suddenly appear during a
"make oldconfig" can be confusing. Add a little helpful text to
the prompt message.
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260110232643.3533351-5-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 79527d86ba91c2d9354832d19fd12b3baa66bd10 ]
SERIAL_IMX_CONSOLE is a build option for the imx driver (SERIAL_IMX).
It does not build a separate console driver file, so it can't be built
as a module since it isn't built at all.
Change the Kconfig symbol from tristate to bool and update the help
text accordingly.
Fixes: 0db4f9b91c86 ("tty: serial: imx: enable imx serial console port as module")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-2-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 29e8a0c587e328ed458380a45d6028adf64d7487 ]
In sprd_clk_init(), when devm_clk_get() returns -EPROBE_DEFER
for either uart or source clock, we should propagate the
error instead of just warning and continuing with NULL clocks.
Currently the driver only emits a warning when clock acquisition
fails and proceeds with NULL clock pointers. This can lead to
issues later when the clocks are actually needed. More importantly,
when the clock provider is not ready yet and returns -EPROBE_DEFER,
we should return this error to allow deferred probing.
This change adds explicit checks for -EPROBE_DEFER after both:
1. devm_clk_get(uport->dev, uart)
2. devm_clk_get(uport->dev, source)
When -EPROBE_DEFER is encountered, the function now returns
-EPROBE_DEFER to let the driver framework retry probing
later when the clock dependencies are resolved.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Link: https://patch.msgid.link/20251022030840.956589-1-Wenhua.Lin@unisoc.com
Reviewed-by: Cixi Geng <cixi.geng@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0e5a99e0e5f50353b86939ff6e424800d769c818 upstream.
Addi-Data GmbH is manufacturing multi-serial ports cards supporting CompactPCI (known as CPCI).
Those cards are identified with different DeviceIds. Those cards integrating standard UARTs
work the same way as PCI/PCIe models already supported in the serial driver.
Signed-off-by: Magne Bruno <magne.bruno@addi-data.com>
Link: https://patch.msgid.link/20251110162456.341029-1-magne.bruno@addi-data.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb4917f557d43c7a1c805dd73ffcdfddb2aba39a upstream.
Check for returned DMA addresses using specialized dma_mapping_error()
helper which is generally recommended for this purpose by
Documentation/core-api/dma-api.rst:
"In some circumstances dma_map_single(), ...
will fail to create a mapping. A driver can check for these errors
by testing the returned DMA address with dma_mapping_error()."
Found via static analysis and this is similar to commit fa0308134d26
("ALSA: memalloc: prefer dma_mapping_error() over explicit address checking")
Fixes: 58ac1b379979 ("ARM: PL011: Fix DMA support")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://patch.msgid.link/20251027092053.87937-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit daeb4037adf7d3349b4a1fb792f4bc9824686a4b ]
Check the return value of reset_control_deassert() in the probe
function to prevent continuing probe when reset deassertion fails.
Previously, reset_control_deassert() was called without checking its
return value, which could lead to probe continuing even when the
device reset wasn't properly deasserted.
The fix checks the return value and returns an error with dev_err_probe()
if reset deassertion fails, providing better error handling and
diagnostics.
Fixes: acbdad8dd1ab ("serial: 8250_dw: simplify optional reset handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251019095131.252848-1-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 295b09128d12fb1a7a67f771cc0ae0df869eafaf ]
Slightly simplify ->probe() and drop a few goto labels by using
devm_add_action_or_reset() for clock and reset cleanup.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220509172129.37770-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: daeb4037adf7 ("serial: 8250_dw: handle reset control deassert error")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7cbce761fe3fcbcb49bcf30d4f8ca5e1a9ee2a0 upstream.
The Advantech 2-port serial card with PCI vendor=0x13fe and device=0x0018
has a 'XR17V35X' chip installed on the circuit board. Therefore, this
driver can be used instead of theu outdated out-of-tree driver from the
manufacturer.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20250924134115.2667650-1-fe@dev.tdt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 672a37ba8af1f2ebcedeb94aea2cdd047f805f30 ]
Check if devm_i2c_new_dummy_device() fails.
Fixes: 2e1f2d9a9bdb ("serial: max310x: implement I2C support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/aJTMPZiKqeXSE-KM@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit cc4d900d0d6d8dd5c41832a93ff3cfa629a78f9a upstream.
Console can be enabled on the UART compile as module.
Change dependency to allow console mode when the driver is built as module.
Fixes: 48a6092fb41fa ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Link: https://lore.kernel.org/r/20250822141923.61133-1-raphael.gallais-pou@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 535fd4c98452c87537a40610abba45daf5761ec6 ]
When trying to set MCR[2], XON1 is incorrectly accessed instead. And when
writing to the TCR register to configure flow control levels, we are
incorrectly writing to the MSR register. The default value of $00 is then
used for TCR, which means that selectable trigger levels in FCR are used
in place of TCR.
TCR/TLR access requires EFR[4] (enable enhanced functions) and MCR[2]
to be set. EFR[4] is already set in probe().
MCR access requires LCR[7] to be zero.
Since LCR is set to $BF when trying to set MCR[2], XON1 is incorrectly
accessed instead because MCR shares the same address space as XON1.
Since MCR[2] is unmodified and still zero, when writing to TCR we are in
fact writing to MSR because TCR/TLR registers share the same address space
as MSR/SPR.
Fix by first removing useless reconfiguration of EFR[4] (enable enhanced
functions), as it is already enabled in sc16is7xx_probe() since commit
43c51bb573aa ("sc16is7xx: make sure device is in suspend once probed").
Now LCR is $00, which means that MCR access is enabled.
Also remove regcache_cache_bypass() calls since we no longer access the
enhanced registers set, and TCR is already declared as volatile (in fact
by declaring MSR as volatile, which shares the same address).
Finally disable access to TCR/TLR registers after modifying them by
clearing MCR[2].
Note: the comment about "... and internal clock div" is wrong and can be
ignored/removed as access to internal clock div registers (DLL/DLH)
is permitted only when LCR[7] is logic 1, not when enhanced features
is enabled. And DLL/DLH access is not needed in sc16is7xx_startup().
Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20250731124451.1108864-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ changed regmap variable from one->regmap to s->regmap ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cfd956dcb101aa3d25bac321fae923323a47c607 upstream.
After hvc_write completes, call hvc_kick also in the case the output
buffer has been drained, to ensure tty_wakeup gets called.
This fixes that functions which wait for a drained buffer got stuck
occasionally.
Cc: stable <stable@kernel.org>
Closes: https://bugzilla.opensuse.org/show_bug.cgi?id=1230062
Signed-off-by: Fabian Vogt <fvogt@suse.de>
Link: https://lore.kernel.org/r/2011735.PYKUYFuaPT@fvogt-thinkpad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b43cb4ff85da5cf29c4cd351ef1d7dd8210780f7 upstream.
The maximum number of keycodes got bumped to 256 a very long time ago,
but the default keymaps were never adjusted to match. This is causing
the kernel to interpret keycodes above 127 as U+0000 if the shipped
generated keymap is used.
Fix this by mapping all keycodes above 127 to K_HOLE so the kernel
ignores them.
The contents of this patche were generated by rerunning `loadkeys
--mktable --unicode` and only including the changes to map keycodes
above 127 to K_HOLE.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250702-vt-misc-unicode-fixes-v1-2-c27e143cc2eb@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1cc2092ea7a52e2c435aee6d2b1bcb773202663 upstream.
We don't process Unicode characters if the virtual terminal is in raw
mode, so there's no reason why we shouldn't do the same for K_OFF
(especially since people would expect K_OFF to actually turn off all VT
key processing).
Fixes: 9fc3de9c8356 ("vt: Add virtual console keyboard mode OFF")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250702-vt-misc-unicode-fixes-v1-1-c27e143cc2eb@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f8fdd4dbffc05982b96caf586f77a014b2a9353 upstream.
When the PSLVERR_RESP_EN parameter is set to 1, the device generates
an error response if an attempt is made to read an empty RBR (Receive
Buffer Register) while the FIFO is enabled.
In serial8250_do_startup(), calling serial_port_out(port, UART_LCR,
UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes
dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter
function enables the FIFO via serial_out(p, UART_FCR, p->fcr).
Execution proceeds to the serial_port_in(port, UART_RX).
This satisfies the PSLVERR trigger condition.
When another CPU (e.g., using printk()) is accessing the UART (UART
is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) ==
(lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter
dw8250_force_idle().
Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock
to fix this issue.
Panic backtrace:
[ 0.442336] Oops - unknown exception [#1]
[ 0.442343] epc : dw8250_serial_in32+0x1e/0x4a
[ 0.442351] ra : serial8250_do_startup+0x2c8/0x88e
...
[ 0.442416] console_on_rootfs+0x26/0x70
Fixes: c49436b657d0 ("serial: 8250_dw: Improve unwritable LCR workaround")
Link: https://lore.kernel.org/all/84cydt5peu.fsf@jogness.linutronix.de/T/
Signed-off-by: Yunhui Cui <cuiyunhui@bytedance.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250723023322.464-2-cuiyunhui@bytedance.com
[ Applied fix to serial8250_do_startup() instead of serial8250_initialize() ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c0e9f05c9d7875995b0e92ace71be947f280bbd upstream.
The dma_sync_sg_for_device() functions should be called with the same
nents as the dma_map_sg(), not the value the map function returned
according to the documentation in Documentation/core-api/dma-api.rst:450:
With the sync_sg API, all the parameters must be the same
as those passed into the sg mapping API.
Fixes: da3564ee027e ("pch_uart: add multi-scatter processing")
Cc: stable <stable@kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250701113452.18590-2-fourier.thomas@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ff78538e07fa284ce08cbbcb0730daa91ed16722 ]
Programs using poll() on /dev/vcsa to be notified when VT changes occur
were missing one case: the switch from gfx to text mode.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/9o5ro928-0pp4-05rq-70p4-ro385n21n723@onlyvoer.pbz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 651dee03696e1dfde6d9a7e8664bbdcd9a10ea7f upstream.
In the sh-sci driver, serial ports are mapped to the sci_ports[] array,
with earlycon mapped at index zero.
The uart_add_one_port() function eventually calls __device_attach(),
which, in turn, calls pm_request_idle(). The identified code path is as
follows:
uart_add_one_port() ->
serial_ctrl_register_port() ->
serial_core_register_port() ->
serial_core_port_device_add() ->
serial_base_port_add() ->
device_add() ->
bus_probe_device() ->
device_initial_probe() ->
__device_attach() ->
// ...
if (dev->p->dead) {
// ...
} else if (dev->driver) {
// ...
} else {
// ...
pm_request_idle(dev);
// ...
}
The earlycon device clocks are enabled by the bootloader. However, the
pm_request_idle() call in __device_attach() disables the SCI port clocks
while earlycon is still active.
The earlycon write function, serial_console_write(), calls
sci_poll_put_char() via serial_console_putchar(). If the SCI port clocks
are disabled, writing to earlycon may sometimes cause the SR.TDFE bit to
remain unset indefinitely, causing the while loop in sci_poll_put_char()
to never exit. On single-core SoCs, this can result in the system being
blocked during boot when this issue occurs.
To resolve this, increment the runtime PM usage counter for the earlycon
SCI device before registering the UART port.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f1017069933489add0c08659673443c9905659e upstream.
The early_console_setup() function initializes sci_ports[0].port with an
object of type struct uart_port obtained from the struct earlycon_device
passed as an argument to early_console_setup().
Later, during serial port probing, the serial port used as earlycon
(e.g., port A) might be remapped to a different position in the sci_ports[]
array, and a different serial port (e.g., port B) might be assigned to slot
0. For example:
sci_ports[0] = port B
sci_ports[X] = port A
In this scenario, the new port mapped at index zero (port B) retains the
data associated with the earlycon configuration. Consequently, after the
Linux boot process, any access to the serial port now mapped to
sci_ports[0] (port B) will block the original earlycon port (port A).
To address this, introduce an early_console_exit() function to clean up
sci_ports[0] when earlycon is exited.
To prevent the cleanup of sci_ports[0] while the serial device is still
being used by earlycon, introduce the struct sci_port::probing flag and
account for it in early_console_exit().
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 239f11209e5f282e16f5241b99256e25dd0614b6 upstream.
Relocate the runtime PM enable operation to sci_probe_single(). This change
prepares the codebase for upcoming fixes.
While at it, replace the existing logic with a direct call to
devm_pm_runtime_enable() and remove sci_cleanup_single(). The
devm_pm_runtime_enable() function automatically handles disabling runtime
PM during driver removal.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 7cc0e0a43a91052477c2921f924a37d9c3891f0c upstream.
On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port()
is called. The uart_suspend_port() calls 3 times the
struct uart_port::ops::tx_empty() before shutting down the port.
According to the documentation, the struct uart_port::ops::tx_empty()
API tests whether the transmitter FIFO and shifter for the port is
empty.
The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the
transmit FIFO through the FDR (FIFO Data Count Register). The data units
in the FIFOs are written in the shift register and transmitted from there.
The TEND bit in the Serial Status Register reports if the data was
transmitted from the shift register.
In the previous code, in the tx_empty() API implemented by the sh-sci
driver, it is considered that the TX is empty if the hardware reports the
TEND bit set and the number of data units in the FIFO is zero.
According to the HW manual, the TEND bit has the following meaning:
0: Transmission is in the waiting state or in progress.
1: Transmission is completed.
It has been noticed that when opening the serial device w/o using it and
then switch to a power saving mode, the tx_empty() call in the
uart_port_suspend() function fails, leading to the "Unable to drain
transmitter" message being printed on the console. This is because the
TEND=0 if nothing has been transmitted and the FIFOs are empty. As the
TEND=0 has double meaning (waiting state, in progress) we can't
determined the scenario described above.
Add a software workaround for this. This sets a variable if any data has
been sent on the serial console (when using PIO) or if the DMA callback has
been called (meaning something has been transmitted). In the tx_empty()
API the status of the DMA transaction is also checked and if it is
completed or in progress the code falls back in checking the hardware
registers instead of relying on the software variable.
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[claudiu.beznea: fixed conflict by:
- keeping serial_port_out() instead of sci_port_out() in
sci_transmit_chars()
- keeping !uart_circ_empty(xmit) condition in sci_dma_tx_complete(),
after s->tx_occurred = true; assignement]
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c4c7ead7b86c1e7f11c64915b7e5bb6d2e242691 ]
They are listed amon those cmd values that "treat 'arg' as an integer"
which is wrong. They should instead fall into the default case. Probably
nobody ever relied on that code since 2009 but still.
Fixes: e92166517e3c ("tty: handle VT specific compat ioctls in vt driver")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/pr214s15-36r8-6732-2pop-159nq85o48r7@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
