summaryrefslogtreecommitdiff
path: root/drivers/tty/serial
AgeCommit message (Collapse)AuthorFilesLines
2021-03-17Revert "serial: max310x: rework RX interrupt handling"Alexander Shiyan1-24/+5
commit 2334de198fed3da72e9785ecdd691d101aa96e77 upstream. This reverts commit fce3c5c1a2d9cd888f2987662ce17c0c651916b2. FIFO is triggered 4 intervals after receiving a byte, it's good when we don't care about the time of reception, but are only interested in the presence of any activity on the line. Unfortunately, this method is not suitable for all tasks, for example, the RS-485 protocol will not work properly, since the state machine must track the request-response time and after the timeout expires, a decision is made that the device on the line is not responding. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Link: https://lore.kernel.org/r/20210217080608.31192-1-shc_work@mail.ru Fixes: fce3c5c1a2d9 ("serial: max310x: rework RX interrupt handling") Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-27serial: mvebu-uart: fix tx lost characters at power offPali Rohár1-1/+9
commit 54ca955b5a4024e2ce0f206b03adb7109bc4da26 upstream. Commit c685af1108d7 ("serial: mvebu-uart: fix tx lost characters") fixed tx lost characters at low baud rates but started causing tx lost characters when kernel is going to power off or reboot. TX_EMP tells us when transmit queue is empty therefore all characters were transmitted. TX_RDY tells us when CPU can send a new character. Therefore we need to use different check prior transmitting new character and different check after all characters were sent. This patch splits polling code into two functions: wait_for_xmitr() which waits for TX_RDY and wait_for_xmite() which waits for TX_EMP. When rebooting A3720 platform without this patch on UART is print only: [ 42.699� And with this patch on UART is full output: [ 39.530216] reboot: Restarting system Fixes: c685af1108d7 ("serial: mvebu-uart: fix tx lost characters") Signed-off-by: Pali Rohár <pali@kernel.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201223191931.18343-1-pali@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-27riscv: Fix sifive serial driverDamien Le Moal1-0/+1
[ Upstream commit 1f1496a923b6ba16679074fe77100e1b53cdb880 ] Setup the port uartclk in sifive_serial_probe() so that the base baud rate is correctly printed during device probe instead of always showing "0". I.e. the probe message is changed from 38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1, base_baud = 0) is a SiFive UART v0 to the correct: 38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1, base_baud = 115200) is a SiFive UART v0 Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com> Acked-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-12-30m68k: Fix WARNING splat in pmac_zilog driverFinn Thain1-5/+9
commit a7b5458ce73b235be027cf2658c39b19b7e58cf2 upstream. Don't add platform resources that won't be used. This avoids a recently-added warning from the driver core, that can show up on a multi-platform kernel when !MACH_IS_MAC. ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at drivers/base/platform.c:224 platform_get_irq_optional+0x8e/0xce 0 is an invalid IRQ number Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 5.9.0-multi #1 Stack from 004b3f04: 004b3f04 00462c2f 00462c2f 004b3f20 0002e128 004754db 004b6ad4 004b3f4c 0002e19c 004754f7 000000e0 00285ba0 00000009 00000000 004b3f44 ffffffff 004754db 004b3f64 004b3f74 00285ba0 004754f7 000000e0 00000009 004754db 004fdf0c 005269e2 004fdf0c 00000000 004b3f88 00285cae 004b6964 00000000 004fdf0c 004b3fac 0051cc68 004b6964 00000000 004b6964 00000200 00000000 0051cc3e 0023c18a 004b3fc0 0051cd8a 004fdf0c 00000002 0052b43c 004b3fc8 Call Trace: [<0002e128>] __warn+0xa6/0xd6 [<0002e19c>] warn_slowpath_fmt+0x44/0x76 [<00285ba0>] platform_get_irq_optional+0x8e/0xce [<00285ba0>] platform_get_irq_optional+0x8e/0xce [<00285cae>] platform_get_irq+0x12/0x4c [<0051cc68>] pmz_init_port+0x2a/0xa6 [<0051cc3e>] pmz_init_port+0x0/0xa6 [<0023c18a>] strlen+0x0/0x22 [<0051cd8a>] pmz_probe+0x34/0x88 [<0051cde6>] pmz_console_init+0x8/0x28 [<00511776>] console_init+0x1e/0x28 [<0005a3bc>] printk+0x0/0x16 [<0050a8a6>] start_kernel+0x368/0x4ce [<005094f8>] _sinittext+0x4f8/0xc48 random: get_random_bytes called from print_oops_end_marker+0x56/0x80 with crng_init=0 ---[ end trace 392d8e82eed68d6c ]--- Commit a85a6c86c25b ("driver core: platform: Clarify that IRQ 0 is invalid"), which introduced the WARNING, suggests that testing for irq == 0 is undesirable. Instead of that comparison, just test for resource existence. Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Joshua Thompson <funaho@jurai.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: stable@vger.kernel.org # v5.8+ Reported-by: Laurent Vivier <laurent@vivier.eu> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Link: https://lore.kernel.org/r/0c0fe1e4f11ccec202d4df09ea7d9d98155d101a.1606001297.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-30serial: 8250-mtk: Fix reference leak in mtk8250_probeZhang Qilong1-3/+10
[ Upstream commit 6e4e636e0e3e0b5deffc5e233adcb2cd4e68f2d0 ] The pm_runtime_enable will increase power disable depth. Thus a pairing decrement is needed on the error handling path to keep it balanced according to context. Fixes: e32a83c70cf98 ("serial: 8250-mtk: modify mtk uart power and clock management") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20201119141126.168850-1-zhangqilong3@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-12-26serial_core: Check for port state when tty is in error stateAlexey Kardashevskiy1-0/+4
commit 2f70e49ed860020f5abae4f7015018ebc10e1f0e upstream. At the moment opening a serial device node (such as /dev/ttyS3) succeeds even if there is no actual serial device behind it. Reading/writing/ioctls fail as expected because the uart port is not initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state bit is set fot the tty. However setting line discipline does not have these checks 8250_port.c (8250 is the default choice made by univ8250_console_init()). As the result of PORT_UNKNOWN, uart_port::iobase is NULL which a platform translates onto some address accessing which produces a crash like below. This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash. Found by syzkaller. Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-21serial: 8250_omap: Avoid FIFO corruption caused by MDR1 accessAlexander Sverdlin1-5/+0
commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream. It has been observed that once per 300-1300 port openings the first transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared as "e" on the wire). It only happened if single byte has been transmitted right after port open, which means, DMA is not used for this transfer and the corruption never happened afterwards. Therefore I've carefully re-read the MDR1 errata (link below), which says "when accessing the MDR1 registers that causes a dummy under-run condition that will freeze the UART in IrDA transmission. In UART mode, this may corrupt the transferred data". Strictly speaking, omap_8250_mdr1_errataset() performs a read access and if the value is the same as should be written, exits without errata-recommended FIFO reset. A brief check of the serial_omap_mdr1_errataset() from the competing omap-serial driver showed it has no read access of MDR1. After removing the read access from omap_8250_mdr1_errataset() the data corruption never happened any more. Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver") Cc: stable@vger.kernel.org Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-12serial: ar933x_uart: disable clk on error handling path in probeZheng Zengkai1-2/+4
ar933x_uart_probe() does not invoke clk_disable_unprepare() on one error handling path. This patch fixes that. Fixes: 9be1064fe524 ("serial: ar933x_uart: add RS485 support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com> Link: https://lore.kernel.org/r/20201111124426.42638-1-zhengzengkai@huawei.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-12tty: serial: imx: keep console clocks always onFugang Duan1-17/+3
For below code, there has chance to cause deadlock in SMP system: Thread 1: clk_enable_lock(); pr_info("debug message"); clk_enable_unlock(); Thread 2: imx_uart_console_write() clk_enable() clk_enable_lock(); Thread 1: Acuired clk enable_lock -> printk -> console_trylock_spinning Thread 2: console_unlock() -> imx_uart_console_write -> clk_disable -> Acquite clk enable_lock So the patch is to keep console port clocks always on like other console drivers. Fixes: 1cf93e0d5488 ("serial: imx: remove the uart_console() check") Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20201111025136.29818-1-fugang.duan@nxp.com Cc: stable <stable@vger.kernel.org> [fix up build warning - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-12tty: serial: imx: fix potential deadlockSam Nobs1-2/+8
Enabling the lock dependency validator has revealed that the way spinlocks are used in the IMX serial port could result in a deadlock. Specifically, imx_uart_int() acquires a spinlock without disabling the interrupts, meaning that another interrupt could come along and try to acquire the same spinlock, potentially causing the two to wait for each other indefinitely. Use spin_lock_irqsave() instead to disable interrupts upon acquisition of the spinlock. Fixes: c974991d2620 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com> Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-06serial: txx9: add missing platform_driver_unregister() on error in ↵Qinglang Miao1-0/+3
serial_txx9_init Add the missing platform_driver_unregister() before return from serial_txx9_init in the error handling case when failed to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI defined. Fixes: ab4382d27412 ("tty: move drivers/serial/ to drivers/tty/serial/") Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-06tty: serial: imx: enable earlycon by default if IMX_SERIAL_CONSOLE is enabledLucas Stach1-0/+1
Since 699cc4dfd140 (tty: serial: imx: add imx earlycon driver), the earlycon part of imx serial is a separate driver and isn't necessarily enabled anymore when the console is enabled. This causes users to loose the earlycon functionality when upgrading their kenrel configuration via oldconfig. Enable earlycon by default when IMX_SERIAL_CONSOLE is enabled. Fixes: 699cc4dfd140 (tty: serial: imx: add imx earlycon driver) Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Link: https://lore.kernel.org/r/20201105204026.1818219-1-l.stach@pengutronix.de Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-06serial: 8250_mtk: Fix uart_get_baud_rate warningClaire Chang1-1/+1
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud rates in both the new and the old termios setting are higher than uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered. Passing NULL as the old termios so uart_get_baud_rate() will use uartclk / 16 - 1 as the new baud rate which will be replaced by the original baud rate later by tty_termios_encode_baud_rate() in mtk8250_set_termios(). Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping") Signed-off-by: Claire Chang <tientzu@chromium.org> Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-28tty: serial: fsl_lpuart: LS1021A has a FIFO size of 16 words, like LS1028AVladimir Oltean1-6/+7
Prior to the commit that this one fixes, the FIFO size was derived from the read-only register LPUARTx_FIFO[TXFIFOSIZE] using the following formula: TX FIFO size = 2 ^ (LPUARTx_FIFO[TXFIFOSIZE] - 1) The documentation for LS1021A is a mess. Under chapter 26.1.3 LS1021A LPUART module special consideration, it mentions TXFIFO_SZ and RXFIFO_SZ being equal to 4, and in the register description for LPUARTx_FIFO, it shows the out-of-reset value of TXFIFOSIZE and RXFIFOSIZE fields as "011", even though these registers read as "101" in reality. And when LPUART on LS1021A was working, the "101" value did correspond to "16 datawords", by applying the formula above, even though the documentation is wrong again (!!!!) and says that "101" means 64 datawords (hint: it doesn't). So the "new" formula created by commit f77ebb241ce0 has all the premises of being wrong for LS1021A, because it relied only on false data and no actual experimentation. Interestingly, in commit c2f448cff22a ("tty: serial: fsl_lpuart: add LS1028A support"), Michael Walle applied a workaround to this by manually setting the FIFO widths for LS1028A. It looks like the same values are used by LS1021A as well, in fact. When the driver thinks that it has a deeper FIFO than it really has, getty (user space) output gets truncated. Many thanks to Michael for pointing out where to look. Fixes: f77ebb241ce0 ("tty: serial: fsl_lpuart: correct the FIFO depth size") Suggested-by: Michael Walle <michael@walle.cc> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20201023013429.3551026-1-vladimir.oltean@nxp.com Reviewed-by：Fugang Duan <fugang.duan@nxp.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-28tty: serial: 21285: fix lockup on openRussell King1-6/+6
Commit 293f89959483 ("tty: serial: 21285: stop using the unused[] variable from struct uart_port") introduced a bug which stops the transmit interrupt being disabled when there are no characters to transmit - disabling the transmit interrupt at the interrupt controller is the only way to stop an interrupt storm. If this interrupt is not disabled when there are no transmit characters, we end up with an interrupt storm which prevents the machine making forward progress. Fixes: 293f89959483 ("tty: serial: 21285: stop using the unused[] variable from struct uart_port") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/E1kU4GS-0006lE-OO@rmk-PC.armlinux.org.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-24Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds1-1/+1
Pull ARM SoC platform updates from Olof Johansson: "SoC changes, a substantial part of this is cleanup of some of the older platforms that used to have a bunch of board files. In particular: - Remove non-DT i.MX platforms that haven't seen activity in years, it's time to remove them. - A bunch of cleanup and removal of platform data for TI/OMAP platforms, moving over to genpd for power/reset control (yay!) - Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them closer to multiplatform support (not quite there yet, but getting close). There are a few other changes too, smaller fixlets, etc. For new platform support, the primary ones are: - New SoC: Hisilicon SD5203, ARM926EJ-S platform. - Cpufreq support for i.MX7ULP" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits) ARM: mstar: Select MStar intc ARM: stm32: Replace HTTP links with HTTPS ones ARM: debug: add UART early console support for SD5203 ARM: hisi: add support for SD5203 SoC ARM: omap3: enable off mode automatically clk: imx: imx35: Remove mx35_clocks_init() clk: imx: imx31: Remove mx31_clocks_init() clk: imx: imx27: Remove mx27_clocks_init() ARM: imx: Remove unused definitions ARM: imx35: Retrieve the IIM base address from devicetree ARM: imx3: Retrieve the AVIC base address from devicetree ARM: imx3: Retrieve the CCM base address from devicetree ARM: imx31: Retrieve the IIM base address from devicetree ARM: imx27: Retrieve the CCM base address from devicetree ARM: imx27: Retrieve the SYSCTRL base address from devicetree ARM: s3c64xx: bring back notes from removed debug-macro.S ARM: s3c24xx: fix Wunused-variable warning on !MMU ARM: samsung: fix PM debug build with DEBUG_LL but !MMU MAINTAINERS: mark linux-samsung-soc list non-moderated ARM: imx: Remove remnant board file support pieces ...
2020-10-16Merge tag 'mips_5.10' of ↵Linus Torvalds1-5/+4
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS updates from Thomas Bogendoerfer: - removed support for PNX833x alias NXT_STB22x - included Ingenic SoC support into generic MIPS kernels - added support for new Ingenic SoCs - converted workaround selection to use Kconfig - replaced old boot mem functions by memblock_* - enabled COP2 usage in kernel for Loongson64 to make use of 16byte load/stores possible - cleanups and fixes * tag 'mips_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (92 commits) MIPS: DEC: Restore bootmem reservation for firmware working memory area MIPS: dec: fix section mismatch bcm963xx_tag.h: fix duplicated word mips: ralink: enable zboot support MIPS: ingenic: Remove CPU_SUPPORTS_HUGEPAGES MIPS: cpu-probe: remove MIPS_CPU_BP_GHIST option bit MIPS: cpu-probe: introduce exclusive R3k CPU probe MIPS: cpu-probe: move fpu probing/handling into its own file MIPS: replace add_memory_region with memblock MIPS: Loongson64: Clean up numa.c MIPS: Loongson64: Select SMP in Kconfig to avoid build error mips: octeon: Add Ubiquiti E200 and E220 boards MIPS: SGI-IP28: disable use of ll/sc in kernel MIPS: tx49xx: move tx4939_add_memory_regions into only user MIPS: pgtable: Remove used PAGE_USERIO define MIPS: alchemy: Share prom_init implementation MIPS: alchemy: Fix build breakage, if TOUCHSCREEN_WM97XX is disabled MIPS: process: include exec.h header in process.c MIPS: process: Add prototype for function arch_dup_task_struct MIPS: idle: Add prototype for function check_wait ...
2020-10-05serial: mcf: add sysrq capabilityAngelo Dureghello1-0/+1
After some unsuccessful attempts to use sysrq over console, figured out that port->has_sysrq should likely be enabled, as per other architectures, this when CONFIG_SERIAL_MCF_CONSOLE is also enabled. Tested some magic sysrq commands (h, p, t, b), they works now properly. Commands works inside 5 secs after BREAK is sent, as expected. Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com> Link: https://lore.kernel.org/r/20201002140545.477481-1-angelo.dureghello@timesys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-05serial: fsl_lpuart: add sysrq support when using dmaAngelo Dureghello1-0/+57
Add handling of magic sysrq keys when using dma/edma. Tested by sending BREAK followed by a sysrq command inside a 5 secs time window, by: echo 1 > /proc/sys/kernel/sysrq BREAK + h, t, e, b, c Tested also sending a command after 5 secs after BREAK, that's properly ignored. Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com> Link: https://lore.kernel.org/r/20201004161144.1307174-1-angelo.dureghello@timesys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-01serial: max310x: rework RX interrupt handlingThomas Petazzoni1-5/+24
Currently, the RX interrupt logic uses the RXEMPTY interrupt, with the RXEMPTYINV bit set, which means we get an RX interrupt as soon as the RX FIFO is non-empty. However, with the MAX310X having a FIFO of 128 bytes, this makes very poor use of the FIFO: we trigger an interrupt as soon as the RX FIFO has one byte, which means a lot of interrupts, each only collecting a few bytes from the FIFO, causing a significant CPU load. Instead this commit relies on two other RX interrupt events: - MAX310X_IRQ_RXFIFO_BIT, which triggers when the RX FIFO has reached a certain threshold, which we define to be half of the FIFO size. This ensure we get an interrupt before the RX FIFO fills up. - MAX310X_LSR_RXTO_BIT, which triggers when the RX FIFO has received some bytes, and then no more bytes are received for a certain time. Arbitrarily, this time is defined to the time is takes to receive 4 characters. On a Microchip SAMA5D3 platform that is receiving 20 bytes every 16ms over one MAX310X UART, this patch has allowed to reduce the CPU consumption of the interrupt handler thread from ~25% to 6-7%. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Link: https://lore.kernel.org/r/20201001074415.349739-1-thomas.petazzoni@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30serial: 8250_dw: Fix clk-notifier/port suspend deadlockSerge Semin1-35/+19
It has been discovered that there is a potential deadlock between the clock-change-notifier thread and the UART port suspending one: CPU0 (suspend CPU/UART) CPU1 (update clock) ---- ---- lock(&port->mutex); lock((work_completion)(&data->clk_work)); lock(&port->mutex); lock((work_completion)(&data->clk_work)); *** DEADLOCK *** The best way to fix this is to eliminate the CPU0 port->mutex/work-completion scenario. So we suggest to register and unregister the clock-notifier during the DW APB UART port probe/remove procedures, instead of doing that at the points of the port startup/shutdown. Link: https://lore.kernel.org/linux-serial/f1cd5c75-9cda-6896-a4e2-42c5bfc3f5c3@redhat.com Fixes: cc816969d7b5 ("serial: 8250_dw: Fix common clocks usage race condition") Reported-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200923161950.6237-4-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30serial: 8250: Skip uninitialized TTY port baud rate updateSerge Semin1-0/+4
It is erroneous to update the TTY port baud rate if it hasn't been initialized yet, because in that case the TTY struct isn't set. So there is no termios structure to get and re-calculate the baud if the current baud can't be reached. Let's skip the baud rate update then until the port is fully initialized. Note the update UART clock method still sets the uartclk member with a new ref clock value even if the port is turned off. The new UART ref clock rate will be used later on the port starting up procedure. Fixes: 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method") Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200923161950.6237-3-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30serial: 8250: Discard RTS/DTS setting from clock update methodSerge Semin1-1/+0
It has been a mistake to add the MCR register RTS/DTS fields setting in the generic method of the UART reference clock update. There is no point in asserting these lines at that procedure. Just discard the serial8250_out_MCR() mathod invocation from there then. Fixes: 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method") Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200923161950.6237-2-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30tty: serial: imx: disable TXDC IRQ in imx_uart_shutdown() to avoid IRQ stormMatthias Schiffer1-5/+6
The IPG clock is disabled at the end of imx_uart_shutdown(); we really don't want to run any IRQ handlers after this point. At least on i.MX8MN, the UART will happily continue to generate interrupts even with its clocks disabled, but in this state, all register writes are ignored (which will cause the shadow registers to differ from the actual register values, resulting in all kinds of weirdness). In a transfer without DMA, this could lead to the following sequence of events: - The UART finishes its transmission while imx_uart_shutdown() is run, triggering the TXDC interrupt (we can trigger this fairly reliably by writing a single byte to the TTY and closing it right away) - imx_uart_shutdown() finishes, disabling the UART clocks - imx_uart_int() -> imx_uart_transmit_buffer() -> imx_uart_stop_tx() imx_uart_stop_tx() should now clear UCR4_TCEN to disable the TXDC interrupt, but this register write is ineffective. This results in an interrupt storm. To disable all interrupts in the same place, and to avoid setting UCR4 twice, clearing UCR4_OREN is moved below del_timer_sync() as well; this should be harmless. Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Link: https://lore.kernel.org/r/20200925082412.12960-1-matthias.schiffer@ew.tq-group.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30serial: 8250_fsl: Fix TX interrupt handling conditionAndrij Abyzov1-1/+1
This is the port of the commit db1b5bc047b3 ("serial: 8250: Fix TX interrupt handling condition") to the 8250_fsl irq handling logic. Interrupt handler checked THRE bit (transmitter holding register empty) in LSR to detect if TX fifo is empty. In case when there is only receive interrupts the TX handling got called because THRE bit in LSR is set when there is no transmission (FIFO empty). TX handling caused TX stop, which in RS-485 half-duplex mode actually resets receiver FIFO. This is not desired during reception because of possible data loss. The fix is to check if THRI is set in IER in addition of the TX fifo status. THRI in IER is set when TX is started and cleared when TX is stopped. This ensures that TX handling is only called when there is really transmission on going and an interrupt for THRE and not when there are only RX interrupts. Signed-off-by: Andrij Abyzov <aabyzov@slb.com> Link: https://lore.kernel.org/r/20200928144127.87156-1-aabyzov@slb.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30serial: pl011: Fix lockdep splat when handling magic-sysrq interruptPeter Zijlstra1-4/+7
Issuing a magic-sysrq via the PL011 causes the following lockdep splat, which is easily reproducible under QEMU: | sysrq: Changing Loglevel | sysrq: Loglevel set to 9 | | ====================================================== | WARNING: possible circular locking dependency detected | 5.9.0-rc7 #1 Not tainted | ------------------------------------------------------ | systemd-journal/138 is trying to acquire lock: | ffffab133ad950c0 (console_owner){-.-.}-{0:0}, at: console_lock_spinning_enable+0x34/0x70 | | but task is already holding lock: | ffff0001fd47b098 (&port_lock_key){-.-.}-{2:2}, at: pl011_int+0x40/0x488 | | which lock already depends on the new lock. [...] | Possible unsafe locking scenario: | | CPU0 CPU1 | ---- ---- | lock(&port_lock_key); | lock(console_owner); | lock(&port_lock_key); | lock(console_owner); | | *** DEADLOCK *** The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int() before taking 'console_owner' on the printk() path, whereas CPU1 takes the two locks in the opposite order on the printk() path due to setting the "console_owner" prior to calling into into the actual console driver. Fix this in the same way as the msm-serial driver by dropping 'port_lock' before handling the sysrq. Cc: <stable@vger.kernel.org> # 4.19+ Cc: Russell King <linux@armlinux.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck Signed-off-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Will Deacon <will@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30tty: serial: fsl_lpuart: fix lpuart32_poll_get_charPeng Fan1-1/+1
The watermark is set to 1, so we need to input two chars to trigger RDRF using the original logic. With the new logic, we could always get the char when there is data in FIFO. Suggested-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30tty: serial: lpuart: fix lpuart32_write usagePeng Fan1-8/+6
The 2nd and 3rd parameter were wrongly used, and cause kernel abort when doing kgdb debug. Fixes: 1da17d7cf8e2 ("tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs") Cc: stable <stable@vger.kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/20200929091920.22612-1-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30serial: qcom_geni_serial: To correct QUP Version detection logicParas Sharma1-1/+1
For QUP IP versions 2.5 and above the oversampling rate is halved from 32 to 16. Commit ce734600545f ("tty: serial: qcom_geni_serial: Update the oversampling rate") is pushed to handle this scenario. But the existing logic is failing to classify QUP Version 3.0 into the correct group ( 2.5 and above). As result Serial Engine clocks are not configured properly for baud rate and garbage data is sampled to FIFOs from the line. So, fix the logic to detect QUP with versions 2.5 and above. Fixes: ce734600545f ("tty: serial: qcom_geni_serial: Update the oversampling rate") Cc: stable <stable@vger.kernel.org> Signed-off-by: Paras Sharma <parashar@codeaurora.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Link: https://lore.kernel.org/r/1601445926-23673-1-git-send-email-parashar@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-29serial: mvebu-uart: fix unused variable warningQinglang Miao1-1/+1
There's a warning shows that 'ret' becomes an unused variable after simplify the return expression of mvebu_uart_probe(). So remove it. Fixes: b63537020db3 ("serial: mvebu-uart: simplify the return expression of mvebu_uart_probe()") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Link: https://lore.kernel.org/r/20200929085651.158283-1-miaoqinglang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-27serial: mvebu-uart: simplify the return expression of mvebu_uart_probe()Qinglang Miao1-4/+1
Simplify the return expression. Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Link: https://lore.kernel.org/r/20200921131105.93177-1-miaoqinglang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-27tty: serial: imx: fix link error with CONFIG_SERIAL_CORE_CONSOLE=nYang Yingliang1-0/+1
aarch64-linux-gnu-ld: drivers/tty/serial/imx_earlycon.o: in function `imx_uart_console_early_write': imx_earlycon.c:(.text+0x84): undefined reference to `uart_console_write' The driver uses the uart_console_write(), but SERIAL_CORE_CONSOLE is not selected, so uart_console_write is not defined, then we get the error. Fix this by selecting SERIAL_CORE_CONSOLE. Fixes: 699cc4dfd140 ("tty: serial: imx: add imx earlycon driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20200919063240.2754965-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-27pch_uart: drop double zeroingJulia Lawall1-1/+1
sg_init_table zeroes its first argument, so the allocation of that argument doesn't have to. the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,n,flags; @@ x = - kcalloc + kmalloc_array (n,sizeof(struct scatterlist),flags) ... sg_init_table(x,n) // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Link: https://lore.kernel.org/r/1600601186-7420-2-git-send-email-Julia.Lawall@inria.fr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-21Merge 5.9.0-rc6 into tty-nextGreg Kroah-Hartman2-24/+30
We need the tty/serial fixes in here and this resolves a merge issue in the 8250 driver. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16tty: serial: qcom_geni_serial: Fix the UART wakeup issuesatya priya1-1/+1
As a part of system suspend uart_port_suspend is called from the Serial driver, which calls set_mctrl passing mctrl as 0. This makes RFR high(NOT_READY) during suspend. Due to this BT SoC is not able to send wakeup bytes to UART during suspend. Include if check for non-suspend case to keep RFR low during suspend. Signed-off-by: satya priya <skakit@codeaurora.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/1599742438-16811-5-git-send-email-skakit@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: 8250_pci: Add Realtek 816a and 816bTobias Diedrich1-0/+11
These serial ports are exposed by the OOB-management-engine on RealManage-enabled network cards (e.g. AMD DASH enabled systems using Realtek cards). Because these have 3 BARs, they fail the "num_iomem <= 1" check in serial_pci_guess_board. I've manually checked the two IOMEM regions and BAR 2 doesn't seem to respond to reads, but BAR 4 seems to be an MMIO version of the IO ports (untested). With this change, the ports are detected: 0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A 0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A lspci output: 02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550]) Subsystem: 17aa:5082 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 82 IOMMU group: 11 Region 0: I/O ports at 2200 [size=256] Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s (ok), Width x1 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp- ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data Not readable Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [170 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [178 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=150us PortTPowerOnTime=150us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us 02:00.2 0700: 10ec:816b (rev 0e) [...same...] Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: core: fix console port-lock regressionJohan Hovold1-17/+15
Fix the port-lock initialisation regression introduced by commit a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") by making sure that the lock is again initialised during console setup. The console may be registered before the serial controller has been probed in which case the port lock needs to be initialised during console setup by a call to uart_set_options(). The console-detach changes introduced a regression in several drivers by effectively removing that initialisation by not initialising the lock when the port is used as a console (which is always the case during console setup). Add back the early lock initialisation and instead use a new console-reinit flag to handle the case where a console is being re-attached through sysfs. The question whether the console-detach interface should have been added in the first place is left for another discussion. Note that the console-enabled check in uart_set_options() is not redundant because of kgdboc, which can end up reinitialising an already enabled console (see commit 42b6a1baa3ec ("serial_core: Don't re-initialize a previously initialized spinlock.")). Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") Cc: stable <stable@vger.kernel.org> # 5.7 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200909143101.15389-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: core: fix port-lock initialisationJohan Hovold1-8/+6
Commit f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()") tried to work around a breakage introduced by commit a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") by adding a second initialisation of the port lock when registering the port. As reported by the build robots [1], this doesn't really solve the regression introduced by the console-detach changes and also adds a second redundant initialisation of the lock for normal ports. Start cleaning up this mess by removing the redundant initialisation and making sure that the port lock is again initialised once-only for ports that aren't already in use as a console. [1] https://lore.kernel.org/r/20200802054852.GR23458@shao2-debian Fixes: f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()") Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") Cc: stable <stable@vger.kernel.org> # 5.7 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200909143101.15389-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16tty: serial: qcom_geni_serial: 115.2 is a better console default than 9600Douglas Anderson1-1/+1
Commit c5cbc78acf69 ("tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup") fixed a bug by initting a variable that was used in some cases without initialization. However, the "default" baud rate picked by that CL was probably not the best choice. The chances that anyone out there is trying to run a system with kernel messages piped out over a 9600 baud serial port is just about nil. Console messages are printed in a blocking manner. At 9600 baud we print about 1 character per millisecond which means that printing a 40-byte message to the console will take ~40 ms. While it would probably work, it's going to make boot _very_ slow and probably cause the occasional timeout here and there in drivers (heck, even at 115200 console delays can wreck havoc). This has already bit at least two people that I'm aware of that tried to enable serial console by just adding "console=ttyMSM0" (instead of "console=ttyMSM0,115200n8") to the command line, so it seems like it'd be nice to fix. Let's switch the default to 115200. Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200911080054.1.I4c00b921c2f17b6988688046fa7be0f729f8d591@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: pmac_zilog: use for_each_child_of_node() macroQinglang Miao1-1/+1
Use for_each_child_of_node() macro instead of open coding it. Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Link: https://lore.kernel.org/r/20200916062138.191188-1-miaoqinglang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16tty: serial: 8250_mtk: set regshift for mmio32Hsin-Yi Wang1-0/+1
To use mmio32, we also need to set regshift. Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Acked-by: Eddie Huang <eddie.huang@mediatek.com> Link: https://lore.kernel.org/r/20200915054825.3289105-2-hsinyi@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16tty: serial: print earlycon info after match->setupHsin-Yi Wang1-1/+8
8250 devices may modify iotype in their own earlycon setup. For example: 8250_mtk and 8250_uniphier force iotype to be MMIO32. Print earlycon info after match->setup to reflect actual earlycon info. Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Link: https://lore.kernel.org/r/20200915054825.3289105-1-hsinyi@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: ucc_uart: make qe_uart_set_mctrl() staticJason Yan1-1/+1
This eliminates the following sparse warning: drivers/tty/serial/ucc_uart.c:286:6: warning: symbol 'qe_uart_set_mctrl' was not declared. Should it be static? Reported-by: Hulk Robot <hulkci@huawei.com> Acked-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Jason Yan <yanaijie@huawei.com> Link: https://lore.kernel.org/r/20200912033834.143166-1-yanaijie@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: 8250_pci: Remove unused function get_pci_irq()YueHaibing1-9/+0
It is not used since commit 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20200909135103.17768-1-yuehaibing@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-13Merge tag 'samsung-soc-s3c-5.10' of ↵Olof Johansson1-1/+1
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc Samsung S3C24xx and S3C64xx machine code cleanup for v5.10 Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it also touches files shared with S5Pv210 and Exynos. This is mostly Arnd Bergmann work which Krzysztof Kozlowski took over, rebased and polished. The goal is to cleanup, merge and finally make the Samsung S3C24xx and S3C64xx architectures multiplatform. The multiplatform did not happen yet here - just cleaning up and merging into one arch/arm/mach-s3c directory. However this is step forward for multiplatform or at least to keep this code still maintainable. This pulls also branch with changes for Samsung SoC sound drivers from broonie/sound because the cleanups there were part of this series and all further patches depend on them. * tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits) ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup ARM: s3c: Cleanup from old plat-samsung include ARM: s3c: make headers local if possible ARM: s3c: move into a common directory ARM: s3c24xx: stop including mach/hardware.h from mach/io.h cpufreq: s3c24xx: move low-level clk reg access into platform code cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh ARM: s3c: remove cpufreq header dependencies cpufreq: s3c24xx: split out registers fbdev: s3c2410fb: remove mach header dependency ARM: s3c24xx: bast: avoid irq_desc array usage ARM: s3c24xx: spi: avoid hardcoding fiq number in driver ARM: s3c24xx: include mach/irqs.h where needed ARM: s3c24xx: move s3cmci pinctrl handling into board files ARM: s3c24xx: move iis pinctrl config into boards ARM: s3c24xx: move spi fiq handler into platform ARM: s3c: adc: move header to linux/soc/samsung ARM: s3c24xx: move irqchip driver back into platform ARM: s3c24xx: move regs-spi.h into spi driver ARM: s3c64xx: remove mach/hardware.h ... Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org Signed-off-by: Olof Johansson <olof@lixom.net>
2020-09-07MIPS: Replace SIBYTE_1956_WAR by CONFIG_SB1_PASS_2_WORKAROUNDSThomas Bogendoerfer1-5/+4
SB1250 uart bug is related to PASS 2 workarounds. Use config CONFIG_SB1_PASS_2_WORKAROUNDS directly and get rid of SIBYTE_1956_WAR. Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-09-04tty: serial: icom: switch from 'pci_' to 'dma_' APIChristophe JAILLET1-14/+18
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'get_port_memory()', GFP_KERNEL can be used because it is only called from a probe function and no lock is acquired. The call chain is: icom_probe (the probe function) --> icom_load_ports --> get_port_memory When memory is allocated in 'load_code()', GFP_KERNEL can be used because it is only called from a .startup function. icom_open (the .startup function of struct uart_ops) --> startup --> load_code .startup functions are protected using a semaphore and no spinlock is taken. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20200806060507.730142-1-christophe.jaillet@wanadoo.fr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04serial: 8250_fsl: Add ACPI supportkuldip dwivedi1-7/+101
This adds support for ACPI enumerated FSL 16550 UARTs. For supporting ACPI, I added a wrapper so that this driver can be used if firmware has exposed the HID "NXP0018" in DSDT table. This will be built as object file if config "SERIAL_8250_FSL" is enabled which depends on config "SERIAL_8250_CONSOLE". Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com> Link: https://lore.kernel.org/r/20200903113402.12371-1-kuldip.dwivedi@puresoftware.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04serial: stm32: Add RS485 RTS GPIO control againMarek Vasut1-8/+25
While the STM32 does support RS485 drive-enable control within the UART IP itself, some systems have the drive-enable line connected to a pin which cannot be pinmuxed as RTS. Add support for toggling the RTS GPIO line using the modem control GPIOs to provide at least some sort of emulation. Fixes: 7df5081cbf5e ("serial: stm32: Add RS485 RTS GPIO control") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Manivannan Sadhasivam <mani@kernel.org> Cc: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com Link: https://lore.kernel.org/r/20200831171045.205691-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04tty: serial: earlycon dependencyTong Zhang1-0/+1
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON should automatically select SERIAL_CORE, otherwise will result in symbol not found error during linking if SERIAL_CORE is not configured as builtin Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon") Signed-off-by: Tong Zhang <ztong0001@gmail.com> Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-01-05 04:29:00 +0300