summaryrefslogtreecommitdiff
path: root/drivers/tty/serial
AgeCommit message (Collapse)AuthorFilesLines
2020-11-24tty: serial: imx: keep console clocks always onFugang Duan1-17/+3
commit e67c139c488e84e7eae6c333231e791f0e89b3fb upstream. For below code, there has chance to cause deadlock in SMP system: Thread 1: clk_enable_lock(); pr_info("debug message"); clk_enable_unlock(); Thread 2: imx_uart_console_write() clk_enable() clk_enable_lock(); Thread 1: Acuired clk enable_lock -> printk -> console_trylock_spinning Thread 2: console_unlock() -> imx_uart_console_write -> clk_disable -> Acquite clk enable_lock So the patch is to keep console port clocks always on like other console drivers. Fixes: 1cf93e0d5488 ("serial: imx: remove the uart_console() check") Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20201111025136.29818-1-fugang.duan@nxp.com Cc: stable <stable@vger.kernel.org> [fix up build warning - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10serial: txx9: add missing platform_driver_unregister() on error in ↵Qinglang Miao1-0/+3
serial_txx9_init commit 0c5fc92622ed5531ff324b20f014e9e3092f0187 upstream. Add the missing platform_driver_unregister() before return from serial_txx9_init in the error handling case when failed to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI defined. Fixes: ab4382d27412 ("tty: move drivers/serial/ to drivers/tty/serial/") Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10serial: 8250_mtk: Fix uart_get_baud_rate warningClaire Chang1-1/+1
commit 912ab37c798770f21b182d656937072b58553378 upstream. Mediatek 8250 port supports speed higher than uartclk / 16. If the baud rates in both the new and the old termios setting are higher than uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered. Passing NULL as the old termios so uart_get_baud_rate() will use uartclk / 16 - 1 as the new baud rate which will be replaced by the original baud rate later by tty_termios_encode_baud_rate() in mtk8250_set_termios(). Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping") Signed-off-by: Claire Chang <tientzu@chromium.org> Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-29tty: serial: earlycon dependencyTong Zhang1-0/+1
[ Upstream commit 0fb9342d06b0f667b915ba58bfefc030e534a218 ] parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON should automatically select SERIAL_CORE, otherwise will result in symbol not found error during linking if SERIAL_CORE is not configured as builtin Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon") Signed-off-by: Tong Zhang <ztong0001@gmail.com> Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01tty: serial: samsung: Correct clock selection logicJonathan Bakker1-4/+4
[ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ] Some variants of the samsung tty driver can pick which clock to use for their baud rate generation. In the DT conversion, a default clock was selected to be used if a specific one wasn't assigned and then a comparison of which clock rate worked better was done. Unfortunately, the comparison was implemented in such a way that only the default clock was ever actually compared. Fix this by iterating through all possible clocks, except when a specific clock has already been picked via clk_sel (which is only possible via board files). Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01serial: 8250: 8250_omap: Terminate DMA before pushing data on RX timeoutVignesh Raghavendra1-2/+4
[ Upstream commit 7cf4df30a98175033e9849f7f16c46e96ba47f41 ] Terminate and flush DMA internal buffers, before pushing RX data to higher layer. Otherwise, this will lead to data corruption, as driver would end up pushing stale buffer data to higher layer while actual data is still stuck inside DMA hardware and has yet not arrived at the memory. While at that, replace deprecated dmaengine_terminate_all() with dmaengine_terminate_async(). Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01serial: 8250_omap: Fix sleeping function called from invalid context during ↵Peter Ujfalusi1-1/+1
probe [ Upstream commit 4ce35a3617c0ac758c61122b2218b6c8c9ac9398 ] When booting j721e the following bug is printed: [ 1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99 [ 1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1 [ 1.154832] 3 locks held by kworker/0:1/12: [ 1.154836] #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8 [ 1.154852] #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8 [ 1.154860] #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138 [ 1.154872] irq event stamp: 63096 [ 1.154881] hardirqs last enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78 [ 1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80 [ 1.154893] softirqs last enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564 [ 1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140 [ 1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221 [ 1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT) [ 1.154917] Workqueue: events deferred_probe_work_func [ 1.154923] Call trace: [ 1.154928] dump_backtrace+0x0/0x190 [ 1.154933] show_stack+0x14/0x20 [ 1.154940] dump_stack+0xe0/0x148 [ 1.154946] ___might_sleep+0x150/0x1f0 [ 1.154952] __might_sleep+0x4c/0x80 [ 1.154957] wait_for_completion_timeout+0x40/0x140 [ 1.154964] ti_sci_set_device_state+0xa0/0x158 [ 1.154969] ti_sci_cmd_get_device_exclusive+0x14/0x20 [ 1.154977] ti_sci_dev_start+0x34/0x50 [ 1.154984] genpd_runtime_resume+0x78/0x1f8 [ 1.154991] __rpm_callback+0x3c/0x140 [ 1.154996] rpm_callback+0x20/0x80 [ 1.155001] rpm_resume+0x568/0x758 [ 1.155007] __pm_runtime_resume+0x44/0xb0 [ 1.155013] omap8250_probe+0x2b4/0x508 [ 1.155019] platform_drv_probe+0x50/0xa0 [ 1.155023] really_probe+0xd4/0x318 [ 1.155028] driver_probe_device+0x54/0xe8 [ 1.155033] __device_attach_driver+0x80/0xb8 [ 1.155039] bus_for_each_drv+0x74/0xc0 [ 1.155044] __device_attach+0xdc/0x138 [ 1.155049] device_initial_probe+0x10/0x18 [ 1.155053] bus_probe_device+0x98/0xa0 [ 1.155058] deferred_probe_work_func+0x74/0xb0 [ 1.155063] process_one_work+0x280/0x6e8 [ 1.155068] worker_thread+0x48/0x430 [ 1.155073] kthread+0x108/0x138 [ 1.155079] ret_from_fork+0x10/0x18 To fix the bug we need to first call pm_runtime_enable() prior to any pm_runtime calls. Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20200320125200.6772-1-peter.ujfalusi@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01serial: 8250_port: Don't service RX FIFO if throttledVignesh Raghavendra1-1/+15
[ Upstream commit f19c3f6c8109b8bab000afd35580929958e087a9 ] When port's throttle callback is called, it should stop pushing any more data into TTY buffer to avoid buffer overflow. This means driver has to stop HW from receiving more data and assert the HW flow control. For UARTs with auto HW flow control (such as 8250_omap) manual assertion of flow control line is not possible and only way is to allow RX FIFO to fill up, thus trigger auto HW flow control logic. Therefore make sure that 8250 generic IRQ handler does not drain data when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not servicing, RX FIFO would trigger auto HW flow control when FIFO occupancy reaches preset threshold, thus halting RX. Since, error conditions in UART_LSR register are cleared just by reading the register, data has to be drained in case there are FIFO errors, else error information will lost. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01serial: 8250: Avoid error message on reprobeLukas Wunner1-2/+9
commit e0a851fe6b9b619527bd928aa93caaddd003f70c upstream. If the call to uart_add_one_port() in serial8250_register_8250_port() fails, a half-initialized entry in the serial_8250ports[] array is left behind. A subsequent reprobe of the same serial port causes that entry to be reused. Because uart->port.dev is set, uart_remove_one_port() is called for the half-initialized entry and bails out with an error message: bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval) The same happens on failure of mctrl_gpio_init() since commit 4a96895f74c9 ("tty/serial/8250: use mctrl_gpio helpers"). Fix by zeroing the uart->port.dev pointer in the probe error path. The bug was introduced in v2.6.10 by historical commit befff6f5bf5f ("[SERIAL] Add new port registration/unregistration functions."): https://git.kernel.org/tglx/history/c/befff6f5bf5f The commit added an unconditional call to uart_remove_one_port() in serial8250_register_port(). In v3.7, commit 835d844d1a28 ("8250_pnp: do pnp probe before legacy probe") made that call conditional on uart->port.dev which allows me to fix the issue by zeroing that pointer in the error path. Thus, the present commit will fix the problem as far back as v3.7 whereas still older versions need to also cherry-pick 835d844d1a28. Fixes: 835d844d1a28 ("8250_pnp: do pnp probe before legacy probe") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v2.6.10 Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de [iwamatsu: Backported to 4.4, 4.9: adjust context] Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-23serial: 8250_pci: Add Realtek 816a and 816bTobias Diedrich1-0/+11
commit 3c5a87be170aba8ac40982182f812dcff6ed1ad1 upstream. These serial ports are exposed by the OOB-management-engine on RealManage-enabled network cards (e.g. AMD DASH enabled systems using Realtek cards). Because these have 3 BARs, they fail the "num_iomem <= 1" check in serial_pci_guess_board. I've manually checked the two IOMEM regions and BAR 2 doesn't seem to respond to reads, but BAR 4 seems to be an MMIO version of the IO ports (untested). With this change, the ports are detected: 0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A 0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A lspci output: 02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550]) Subsystem: 17aa:5082 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 82 IOMMU group: 11 Region 0: I/O ports at 2200 [size=256] Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s (ok), Width x1 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp- ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data Not readable Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [170 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [178 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=150us PortTPowerOnTime=150us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us 02:00.2 0700: 10ec:816b (rev 0e) [...same...] Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03serial: 8250: change lock order in serial8250_do_startup()Sergey Senozhatsky1-3/+6
commit 205d300aea75623e1ae4aa43e0d265ab9cf195fd upstream. We have a number of "uart.port->desc.lock vs desc.lock->uart.port" lockdep reports coming from 8250 driver; this causes a bit of trouble to people, so let's fix it. The problem is reverse lock order in two different call paths: chain #1: serial8250_do_startup() spin_lock_irqsave(&port->lock); disable_irq_nosync(port->irq); raw_spin_lock_irqsave(&desc->lock) chain #2: __report_bad_irq() raw_spin_lock_irqsave(&desc->lock) for_each_action_of_desc() printk() spin_lock_irqsave(&port->lock); Fix this by changing the order of locks in serial8250_do_startup(): do disable_irq_nosync() first, which grabs desc->lock, and grab uart->port after that, so that chain #1 and chain #2 have same lock order. Full lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.4.39 #55 Not tainted ====================================================== swapper/0/0 is trying to acquire lock: ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57 but task is already holding lock: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&irq_desc_lock_class){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d __irq_get_desc_lock+0x65/0x89 __disable_irq_nosync+0x3b/0x93 serial8250_do_startup+0x451/0x75c uart_startup+0x1b4/0x2ff uart_port_activate+0x73/0xa0 tty_port_open+0xae/0x10a uart_open+0x1b/0x26 tty_open+0x24d/0x3a0 chrdev_open+0xd5/0x1cc do_dentry_open+0x299/0x3c8 path_openat+0x434/0x1100 do_filp_open+0x9b/0x10a do_sys_open+0x15f/0x3d7 kernel_init_freeable+0x157/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #1 (&port_lock_key){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d serial8250_console_write+0xa7/0x2a0 console_unlock+0x3b7/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 register_console+0x336/0x3a4 uart_add_one_port+0x51b/0x5be serial8250_register_8250_port+0x454/0x55e dw8250_probe+0x4dc/0x5b9 platform_drv_probe+0x67/0x8b really_probe+0x14a/0x422 driver_probe_device+0x66/0x130 device_driver_attach+0x42/0x5b __driver_attach+0xca/0x139 bus_for_each_dev+0x97/0xc9 bus_add_driver+0x12b/0x228 driver_register+0x64/0xed do_one_initcall+0x20c/0x4a6 do_initcall_level+0xb5/0xc5 do_basic_setup+0x4c/0x58 kernel_init_freeable+0x13f/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #0 (console_owner){-...}: __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 console_lock_spinning_enable+0x51/0x57 console_unlock+0x25d/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 ret_from_intr+0x0/0x1d cpuidle_enter_state+0x12f/0x1fd cpuidle_enter+0x2e/0x3d do_idle+0x1ce/0x2ce cpu_startup_entry+0x1d/0x1f start_kernel+0x406/0x46a secondary_startup_64+0xa4/0xb0 other info that might help us debug this: Chain exists of: console_owner --> &port_lock_key --> &irq_desc_lock_class Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&irq_desc_lock_class); lock(&port_lock_key); lock(&irq_desc_lock_class); lock(console_owner); *** DEADLOCK *** 2 locks held by swapper/0/0: #0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba #1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55 Hardware name: XXXXXX Call Trace: <IRQ> dump_stack+0xbf/0x133 ? print_circular_bug+0xd6/0xe9 check_noncircular+0x1b9/0x1c3 __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 ? console_lock_spinning_enable+0x31/0x57 console_lock_spinning_enable+0x51/0x57 ? console_lock_spinning_enable+0x31/0x57 console_unlock+0x25d/0x528 ? console_trylock+0x18/0x4e vprintk_emit+0x111/0x17f ? lock_acquire+0x203/0x258 printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 common_interrupt+0xf/0xf </IRQ> Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels") Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: Raul Rangel <rrangel@google.com> BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800 Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03serial: pl011: Don't leak amba_ports entry on driver register errorLukas Wunner1-1/+4
commit 89efbe70b27dd325d8a8c177743a26b885f7faec upstream. pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry, then calls pl011_register_port() to register the uart driver with the tty layer. If registration of the uart driver fails, the amba_ports[] entry is not released. If this happens 14 times (value of UART_NR macro), then all amba_ports[] entries will have been leaked and driver probing is no longer possible. (To be fair, that can only happen if the DeviceTree doesn't contain alias IDs since they cause the same entry to be used for a given port.) Fix it. Fixes: ef2889f7ffee ("serial: pl011: Move uart_register_driver call to device") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v3.15+ Cc: Tushar Behera <tushar.behera@linaro.org> Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03serial: pl011: Fix oops on -EPROBE_DEFERLukas Wunner1-6/+5
commit 27afac93e3bd7fa89749cf11da5d86ac9cde4dba upstream. If probing of a pl011 gets deferred until after free_initmem(), an oops ensues because pl011_console_match() is called which has been freed. Fix by removing the __init attribute from the function and those it calls. Commit 10879ae5f12e ("serial: pl011: add console matching function") introduced pl011_console_match() not just for early consoles but regular preferred consoles, such as those added by acpi_parse_spcr(). Regular consoles may be registered after free_initmem() for various reasons, one being deferred probing, another being dynamic enablement of serial ports using a DeviceTree overlay. Thus, pl011_console_match() must not be declared __init and the functions it calls mustn't either. Stack trace for posterity: Unable to handle kernel paging request at virtual address 80c38b58 Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM PC is at pl011_console_match+0x0/0xfc LR is at register_console+0x150/0x468 [<80187004>] (register_console) [<805a8184>] (uart_add_one_port) [<805b2b68>] (pl011_register_port) [<805b3ce4>] (pl011_probe) [<80569214>] (amba_probe) [<805ca088>] (really_probe) [<805ca2ec>] (driver_probe_device) [<805ca5b0>] (__device_attach_driver) [<805c8060>] (bus_for_each_drv) [<805c9dfc>] (__device_attach) [<805ca630>] (device_initial_probe) [<805c90a8>] (bus_probe_device) [<805c95a8>] (deferred_probe_work_func) Fixes: 10879ae5f12e ("serial: pl011: add console matching function") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.10+ Cc: Aleksey Makarov <amakarov@marvell.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Christopher Covington <cov@codeaurora.org> Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03serial: samsung: Removes the IRQ not found warningTamseel Shams1-3/+5
commit 8c6c378b0cbe0c9f1390986b5f8ffb5f6ff7593b upstream. In few older Samsung SoCs like s3c2410, s3c2412 and s3c2440, UART IP is having 2 interrupt lines. However, in other SoCs like s3c6400, s5pv210, exynos5433, and exynos4210 UART is having only 1 interrupt line. Due to this, "platform_get_irq(platdev, 1)" call in the driver gives the following false-positive error: "IRQ index 1 not found" on newer SoC's. This patch adds the condition to check for Tx interrupt only for the those SoC's which have 2 interrupt lines. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Tamseel Shams <m.shams@samsung.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-31serial: 8250_mtk: Fix high-speed baud rates clampingSerge Semin1-0/+18
commit 551e553f0d4ab623e2a6f424ab5834f9c7b5229c upstream. Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") fixed limits of a baud rate setting for a generic 8250 port. In other words since that commit the baud rate has been permitted to be within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely normal for a standard 8250 UART port. But there are custom 8250 ports, which provide extended baud rate limits. In particular the Mediatek 8250 port can work with baud rates up to "uartclk" speed. Normally that and any other peculiarity is supposed to be handled in a custom set_termios() callback implemented in the vendor-specific 8250-port glue-driver. Currently that is how it's done for the most of the vendor-specific 8250 ports, but for some reason for Mediatek a solution has been spread out to both the glue-driver and to the generic 8250-port code. Due to that a bug has been introduced, which permitted the extended baud rate limit for all even for standard 8250-ports. The bug has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") by narrowing the baud rates limit back down to the normal bounds. Unfortunately by doing so we also broke the Mediatek-specific extended bauds feature. A fix of the problem described above is twofold. First since we can't get back the extended baud rate limits feature to the generic set_termios() function and that method supports only a standard baud rates range, the requested baud rate must be locally stored before calling it and then restored back to the new termios structure after the generic set_termios() finished its magic business. By doing so we still use the serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers, while the extended baud rate setting procedure will be performed later in the custom Mediatek-specific set_termios() callback. Second since a true baud rate is now fully calculated in the custom set_termios() method we need to locally update the port timeout by calling the uart_update_timeout() function. After the fixes described above are implemented in the 8250_mtk.c driver, the Mediatek 8250-port should get back to normally working with extended baud rates. Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com Fixes: 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") Reported-by: Daniel Winkler <danielwinkler@google.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: stable <stable@vger.kernel.org> Tested-by: Claire Chang <tientzu@chromium.org> Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-31serial: 8250: fix null-ptr-deref in serial8250_start_tx()Yang Yingliang1-1/+1
commit f4c23a140d80ef5e6d3d1f8f57007649014b60fa upstream. I got null-ptr-deref in serial8250_start_tx(): [ 78.114630] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 78.123778] Mem abort info: [ 78.126560] ESR = 0x86000007 [ 78.129603] EC = 0x21: IABT (current EL), IL = 32 bits [ 78.134891] SET = 0, FnV = 0 [ 78.137933] EA = 0, S1PTW = 0 [ 78.141064] user pgtable: 64k pages, 48-bit VAs, pgdp=00000027d41a8600 [ 78.147562] [0000000000000000] pgd=00000027893f0003, p4d=00000027893f0003, pud=00000027893f0003, pmd=00000027c9a20003, pte=0000000000000000 [ 78.160029] Internal error: Oops: 86000007 [#1] SMP [ 78.164886] Modules linked in: sunrpc vfat fat aes_ce_blk crypto_simd cryptd aes_ce_cipher crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce ses enclosure sg sbsa_gwdt ipmi_ssif spi_dw_mmio sch_fq_codel vhost_net tun vhost vhost_iotlb tap ip_tables ext4 mbcache jbd2 ahci hisi_sas_v3_hw libahci hisi_sas_main libsas hns3 scsi_transport_sas hclge libata megaraid_sas ipmi_si hnae3 ipmi_devintf ipmi_msghandler br_netfilter bridge stp llc nvme nvme_core xt_sctp sctp libcrc32c dm_mod nbd [ 78.207383] CPU: 11 PID: 23258 Comm: null-ptr Not tainted 5.8.0-rc6+ #48 [ 78.214056] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B210.01 03/12/2020 [ 78.222888] pstate: 80400089 (Nzcv daIf +PAN -UAO BTYPE=--) [ 78.228435] pc : 0x0 [ 78.230618] lr : serial8250_start_tx+0x160/0x260 [ 78.235215] sp : ffff800062eefb80 [ 78.238517] x29: ffff800062eefb80 x28: 0000000000000fff [ 78.243807] x27: ffff800062eefd80 x26: ffff202fd83b3000 [ 78.249098] x25: ffff800062eefd80 x24: ffff202fd83b3000 [ 78.254388] x23: ffff002fc5e50be8 x22: 0000000000000002 [ 78.259679] x21: 0000000000000001 x20: 0000000000000000 [ 78.264969] x19: ffffa688827eecc8 x18: 0000000000000000 [ 78.270259] x17: 0000000000000000 x16: 0000000000000000 [ 78.275550] x15: ffffa68881bc67a8 x14: 00000000000002e6 [ 78.280841] x13: ffffa68881bc67a8 x12: 000000000000c539 [ 78.286131] x11: d37a6f4de9bd37a7 x10: ffffa68881cccff0 [ 78.291421] x9 : ffffa68881bc6000 x8 : ffffa688819daa88 [ 78.296711] x7 : ffffa688822a0f20 x6 : ffffa688819e0000 [ 78.302002] x5 : ffff800062eef9d0 x4 : ffffa68881e707a8 [ 78.307292] x3 : 0000000000000000 x2 : 0000000000000002 [ 78.312582] x1 : 0000000000000001 x0 : ffffa688827eecc8 [ 78.317873] Call trace: [ 78.320312] 0x0 [ 78.322147] __uart_start.isra.9+0x64/0x78 [ 78.326229] uart_start+0xb8/0x1c8 [ 78.329620] uart_flush_chars+0x24/0x30 [ 78.333442] n_tty_receive_buf_common+0x7b0/0xc30 [ 78.338128] n_tty_receive_buf+0x44/0x2c8 [ 78.342122] tty_ioctl+0x348/0x11f8 [ 78.345599] ksys_ioctl+0xd8/0xf8 [ 78.348903] __arm64_sys_ioctl+0x2c/0xc8 [ 78.352812] el0_svc_common.constprop.2+0x88/0x1b0 [ 78.357583] do_el0_svc+0x44/0xd0 [ 78.360887] el0_sync_handler+0x14c/0x1d0 [ 78.364880] el0_sync+0x140/0x180 [ 78.368185] Code: bad PC value SERIAL_PORT_DFNS is not defined on each arch, if it's not defined, serial8250_set_defaults() won't be called in serial8250_isa_init_ports(), so the p->serial_in pointer won't be initialized, and it leads a null-ptr-deref. Fix this problem by calling serial8250_set_defaults() after init uart port. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200721143852.4058352-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-30serial: amba-pl011: Make sure we initialize the port.lock spinlockJohn Stultz1-0/+1
[ Upstream commit 8508f4cba308f785b2fd4b8c38849c117b407297 ] Valentine reported seeing: [ 3.626638] INFO: trying to register non-static key. [ 3.626639] the code is fine but needs lockdep annotation. [ 3.626640] turning off the locking correctness validator. [ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116 [ 3.626646] Hardware name: HiKey960 (DT) [ 3.626656] Workqueue: events deferred_probe_work_func [ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes) [ 3.640220] Call trace: [ 3.640225] dump_backtrace+0x0/0x1b8 [ 3.640227] show_stack+0x20/0x30 [ 3.640230] dump_stack+0xec/0x158 [ 3.640234] register_lock_class+0x598/0x5c0 [ 3.640235] __lock_acquire+0x80/0x16c0 [ 3.640236] lock_acquire+0xf4/0x4a0 [ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8 [ 3.640245] uart_add_one_port+0x388/0x4b8 [ 3.640248] pl011_register_port+0x70/0xf0 [ 3.640250] pl011_probe+0x184/0x1b8 [ 3.640254] amba_probe+0xdc/0x180 [ 3.640256] really_probe+0xe0/0x338 [ 3.640257] driver_probe_device+0x60/0xf8 [ 3.640259] __device_attach_driver+0x8c/0xd0 [ 3.640260] bus_for_each_drv+0x84/0xd8 [ 3.640261] __device_attach+0xe4/0x140 [ 3.640263] device_initial_probe+0x1c/0x28 [ 3.640265] bus_probe_device+0xa4/0xb0 [ 3.640266] deferred_probe_work_func+0x7c/0xb8 [ 3.640269] process_one_work+0x2c0/0x768 [ 3.640271] worker_thread+0x4c/0x498 [ 3.640272] kthread+0x14c/0x158 [ 3.640275] ret_from_fork+0x10/0x1c Which seems to be due to the fact that after allocating the uap structure, nothing initializes the spinlock. Its a little confusing, as uart_port_spin_lock_init() is one place where the lock is supposed to be initialized, but it has an exception for the case where the port is a console. This makes it seem like a deeper fix is needed to properly register the console, but I'm not sure what that entails, and Andy suggested that this approach is less invasive. Thus, this patch resolves the issue by initializing the spinlock in the driver, and resolves the resulting warning. Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-serial@vger.kernel.org Reported-by: Valentin Schneider <valentin.schneider@arm.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com> Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-03sc16is7xx: move label 'err_spi' to correct sectionGuoqing Jiang1-0/+2
commit e00164a0f000de893944981f41a568c981aca658 upstream. err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make the label only available under SERIAL_SC16IS7XX_SPI option. Otherwise, the below warning appears. drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label] err_spi: ^~~~~~~ Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Fixes: ac0cdb3d9901 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11tty:serial:mvebu-uart:fix a wrong returntangbin1-1/+1
commit 4a3e208474204e879d22a310b244cb2f39e5b1f8 upstream. in this place, the function should return a negative value and the PTR_ERR already returns a negative,so return -PTR_ERR() is wrong. Signed-off-by: tangbin <tangbin@cmss.chinamobile.com> Cc: stable <stable@vger.kernel.org> Acked-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20200305013823.20976-1-tangbin@cmss.chinamobile.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-11serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDEDaniel Golle1-0/+8
[ Upstream commit 87c5cbf71ecbb9e289d60a2df22eb686c70bf196 ] On AR934x this UART is usually not initialized by the bootloader as it is only used as a secondary serial port while the primary UART is a newly introduced NS16550-compatible. In order to make use of the ar933x-uart on AR934x without RTS/CTS hardware flow control, one needs to set the UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this UART is used as primary/console, the bootloader on AR934x typically doesn't set those bits. Setting them explicitely on AR933x should not do any harm, so just set them unconditionally. Tested-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-03-11serial: 8250: Check UPF_IRQ_SHARED in advanceAndy Shevchenko2-3/+6
commit 7febbcbc48fc92e3f33863b32ed715ba4aff18c4 upstream. The commit 54e53b2e8081 ("tty: serial: 8250: pass IRQ shared flag to UART ports") nicely explained the problem: ---8<---8<--- On some systems IRQ lines between multiple UARTs might be shared. If so, the irqflags have to be configured accordingly. The reason is: The 8250 port startup code performs IRQ tests *before* the IRQ handler for that particular port is registered. This is performed in serial8250_do_startup(). This function checks whether IRQF_SHARED is configured and only then disables the IRQ line while testing. This test is performed upon each open() of the UART device. Imagine two UARTs share the same IRQ line: On is already opened and the IRQ is active. When the second UART is opened, the IRQ line has to be disabled while performing IRQ tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself cannot be handled, because the corresponding handler isn't registered, yet. That's because the 8250 code uses a chain-handler and invokes the corresponding port's IRQ handling routines himself. Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't disabled while performing tests and the kernel correctly detects a spurious IRQ. So, adding this flag to the DT probe solves the issue. Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the IRQF_SHARED flag can be set unconditionally as well. Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system: |irq 85: nobody cared (try booting with the "irqpoll" option) | [...] |handlers: |[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt |Disabling IRQ #85 ---8<---8<--- But unfortunately didn't fix the root cause. Let's try again here by moving IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup(). This should fix the similar issue reported for 8250_pnp case. Since this change we don't need to have custom solutions in 8250_aspeed_vuart and 8250_of drivers, thus, drop them. Fixes: 1c2f04937b3e ("serial: 8250: add IRQ trigger support") Reported-by: Li RongQing <lirongqing@baidu.com> Cc: Kurt Kanzenbach <kurt@linutronix.de> Cc: Vikram Pandita <vikram.pandita@ti.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable <stable@vger.kernel.org> Acked-by: Kurt Kanzenbach <kurt@linutronix.de> Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com [Kurt: Backport to v4.9] Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-28tty: serial: imx: setup the correct sg entry for tx dmaFugang Duan1-1/+1
commit f76707831829530ffdd3888bebc108aecefccaa0 upstream. There has oops as below happen on i.MX8MP EVK platform that has 6G bytes DDR memory. when (xmit->tail < xmit->head) && (xmit->head == 0), it setups one sg entry with sg->length is zero: sg_set_buf(sgl + 1, xmit->buf, xmit->head); if xmit->buf is allocated from >4G address space, and SDMA only support <4G address space, then dma_map_sg() will call swiotlb_map() to do bounce buffer copying and mapping. But swiotlb_map() don't allow sg entry's length is zero, otherwise report BUG_ON(). So the patch is to correct the tx DMA scatter list. Oops: [ 287.675715] kernel BUG at kernel/dma/swiotlb.c:497! [ 287.680592] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [ 287.686075] Modules linked in: [ 287.689133] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.3-00016-g3fdc4e0-dirty #10 [ 287.696872] Hardware name: FSL i.MX8MP EVK (DT) [ 287.701402] pstate: 80000085 (Nzcv daIf -PAN -UAO) [ 287.706199] pc : swiotlb_tbl_map_single+0x1fc/0x310 [ 287.711076] lr : swiotlb_map+0x60/0x148 [ 287.714909] sp : ffff800010003c00 [ 287.718221] x29: ffff800010003c00 x28: 0000000000000000 [ 287.723533] x27: 0000000000000040 x26: ffff800011ae0000 [ 287.728844] x25: ffff800011ae09f8 x24: 0000000000000000 [ 287.734155] x23: 00000001b7af9000 x22: 0000000000000000 [ 287.739465] x21: ffff000176409c10 x20: 00000000001f7ffe [ 287.744776] x19: ffff000176409c10 x18: 000000000000002e [ 287.750087] x17: 0000000000000000 x16: 0000000000000000 [ 287.755397] x15: 0000000000000000 x14: 0000000000000000 [ 287.760707] x13: ffff00017f334000 x12: 0000000000000001 [ 287.766018] x11: 00000000001fffff x10: 0000000000000000 [ 287.771328] x9 : 0000000000000003 x8 : 0000000000000000 [ 287.776638] x7 : 0000000000000000 x6 : 0000000000000000 [ 287.781949] x5 : 0000000000200000 x4 : 0000000000000000 [ 287.787259] x3 : 0000000000000001 x2 : 00000001b7af9000 [ 287.792570] x1 : 00000000fbfff000 x0 : 0000000000000000 [ 287.797881] Call trace: [ 287.800328] swiotlb_tbl_map_single+0x1fc/0x310 [ 287.804859] swiotlb_map+0x60/0x148 [ 287.808347] dma_direct_map_page+0xf0/0x130 [ 287.812530] dma_direct_map_sg+0x78/0xe0 [ 287.816453] imx_uart_dma_tx+0x134/0x2f8 [ 287.820374] imx_uart_dma_tx_callback+0xd8/0x168 [ 287.824992] vchan_complete+0x194/0x200 [ 287.828828] tasklet_action_common.isra.0+0x154/0x1a0 [ 287.833879] tasklet_action+0x24/0x30 [ 287.837540] __do_softirq+0x120/0x23c [ 287.841202] irq_exit+0xb8/0xd8 [ 287.844343] __handle_domain_irq+0x64/0xb8 [ 287.848438] gic_handle_irq+0x5c/0x148 [ 287.852185] el1_irq+0xb8/0x180 [ 287.855327] cpuidle_enter_state+0x84/0x360 [ 287.859508] cpuidle_enter+0x34/0x48 [ 287.863083] call_cpuidle+0x18/0x38 [ 287.866571] do_idle+0x1e0/0x280 [ 287.869798] cpu_startup_entry+0x20/0x40 [ 287.873721] rest_init+0xd4/0xe0 [ 287.876949] arch_call_rest_init+0xc/0x14 [ 287.880958] start_kernel+0x420/0x44c [ 287.884622] Code: 9124c021 9417aff8 a94363f7 17ffffd5 (d4210000) [ 287.890718] ---[ end trace 5bc44c4ab6b009ce ]--- [ 287.895334] Kernel panic - not syncing: Fatal exception in interrupt [ 287.901686] SMP: stopping secondary CPUs [ 288.905607] SMP: failed to stop secondary CPUs 0-1 [ 288.910395] Kernel Offset: disabled [ 288.913882] CPU features: 0x0002,2000200c [ 288.917888] Memory Limit: none [ 288.920944] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]--- Reported-by: Eagle Zhou <eagle.zhou@nxp.com> Tested-by: Eagle Zhou <eagle.zhou@nxp.com> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Cc: stable <stable@vger.kernel.org> Fixes: 7942f8577f2a ("serial: imx: TX DMA: clean up sg initialization") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/1581401761-6378-1-git-send-email-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-28tty/serial: atmel: manage shutdown in case of RS485 or ISO7816 modeNicolas Ferre1-1/+2
commit 04b5bfe3dc94e64d0590c54045815cb5183fb095 upstream. In atmel_shutdown() we call atmel_stop_rx() and atmel_stop_tx() functions. Prevent the rx restart that is implemented in RS485 or ISO7816 modes when calling atmel_stop_tx() by using the atomic information tasklet_shutdown that is already in place for this purpose. Fixes: 98f2082c3ac4 ("tty/serial: atmel: enforce tasklet init and termination sequences") Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200210152053.8289-1-nicolas.ferre@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-05serial: 8250_bcm2835aux: Fix line mismatch on driver unbindLukas Wunner1-1/+1
commit dc76697d7e933d5e299116f219c890568785ea15 upstream. Unbinding the bcm2835aux UART driver raises the following error if the maximum number of 8250 UARTs is set to 1 (via the 8250.nr_uarts module parameter or CONFIG_SERIAL_8250_RUNTIME_UARTS): (NULL device *): Removing wrong port: a6f80333 != fa20408b That's because bcm2835aux_serial_probe() retrieves UART line number 1 from the devicetree and stores it in data->uart.port.line, while serial8250_register_8250_port() instead uses UART line number 0, which is stored in data->line. On driver unbind, bcm2835aux_serial_remove() uses data->uart.port.line, which contains the wrong number. Fix it. The issue does not occur if the maximum number of 8250 UARTs is >= 2. Fixes: bdc5f3009580 ("serial: bcm2835: add driver for bcm2835-aux-uart") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.6+ Cc: Martin Sperl <kernel@martin.sperl.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/912ccf553c5258135c6d7e8f404a101ef320f0f4.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29serial: stm32: fix transmit_chars when tx is stoppedErwan Le Ray1-8/+3
[ Upstream commit b83b957c91f68e53f0dc596e129e8305761f2a32 ] Disables the tx irq when the transmission is ended and updates stop_tx conditions for code cleanup. Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver") Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-01-23tty: serial: pch_uart: correct usage of dma_unmap_sgPeng Fan1-1/+4
commit 74887542fdcc92ad06a48c0cca17cdf09fc8aa00 upstream. Per Documentation/DMA-API-HOWTO.txt, To unmap a scatterlist, just call: dma_unmap_sg(dev, sglist, nents, direction); .. note:: The 'nents' argument to the dma_unmap_sg call must be the _same_ one you passed into the dma_map_sg call, it should _NOT_ be the 'count' value _returned_ from the dma_map_sg call. However in the driver, priv->nent is directly assigned with value returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap, this breaks the API usage. So introduce a new entry orig_nent to remember 'nents'. Fixes: da3564ee027e ("pch_uart: add multi-scatter processing") Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1573623259-6339-1-git-send-email-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-23tty: serial: imx: use the sg count from dma_map_sgPeng Fan1-1/+1
commit 596fd8dffb745afcebc0ec6968e17fe29f02044c upstream. The dmaengine_prep_slave_sg needs to use sg count returned by dma_map_sg, not use sport->dma_tx_nents, because the return value of dma_map_sg is not always same with "nents". Fixes: b4cdc8f61beb ("serial: imx: add DMA support for imx6q") Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1573108875-26530-1-git-send-email-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty: link tty and port before configuring it as consoleSudip Mukherjee1-0/+1
commit fb2b90014d782d80d7ebf663e50f96d8c507a73c upstream. There seems to be a race condition in tty drivers and I could see on many boot cycles a NULL pointer dereference as tty_init_dev() tries to do 'tty->port->itty = tty' even though tty->port is NULL. 'tty->port' will be set by the driver and if the driver has not yet done it before we open the tty device we can get to this situation. By adding some extra debug prints, I noticed that: 6.650130: uart_add_one_port 6.663849: register_console 6.664846: tty_open 6.674391: tty_init_dev 6.675456: tty_port_link_device uart_add_one_port() registers the console, as soon as it registers, the userspace tries to use it and that leads to tty_open() but uart_add_one_port() has not yet done tty_port_link_device() and so tty->port is not yet configured when control reaches tty_init_dev(). Further look into the code and tty_port_link_device() is done by uart_add_one_port(). After registering the console uart_add_one_port() will call tty_port_register_device_attr_serdev() and tty_port_link_device() is called from this. Call add tty_port_link_device() before uart_configure_port() is done and add a check in tty_port_link_device() so that it only links the port if it has not been done yet. Suggested-by: Jiri Slaby <jslaby@suse.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191212131602.29504-1-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-12tty: serial: msm_serial: Fix lockup for sysrq and oopsLeo Yan1-2/+11
commit 0e4f7f920a5c6bfe5e851e989f27b35a0cc7fb7e upstream. As the commit 677fe555cbfb ("serial: imx: Fix recursive locking bug") has mentioned the uart driver might cause recursive locking between normal printing and the kernel debugging facilities (e.g. sysrq and oops). In the commit it gave out suggestion for fixing recursive locking issue: "The solution is to avoid locking in the sysrq case and trylock in the oops_in_progress case." This patch follows the suggestion (also used the exactly same code with other serial drivers, e.g. amba-pl011.c) to fix the recursive locking issue, this can avoid stuck caused by deadlock and print out log for sysrq and oops. Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") Signed-off-by: Leo Yan <leo.yan@linaro.org> Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Link: https://lore.kernel.org/r/20191127141544.4277-2-leo.yan@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04tty/serial: atmel: fix out of range clock divider handlingDavid Engraf1-21/+22
[ Upstream commit cb47b9f8630ae3fa3f5fbd0c7003faba7abdf711 ] Use MCK_DIV8 when the clock divider is > 65535. Unfortunately the mode register was already written thus the clock selection is ignored. Fix by doing the baud rate calulation before setting the mode. Fixes: 5bf5635ac170 ("tty/serial: atmel: add fractional baud rate support") Signed-off-by: David Engraf <david.engraf@sysgo.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191216085403.17050-1-david.engraf@sysgo.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-21serial: imx: fix error handling in console_setupStefan Agner1-1/+1
[ Upstream commit 63fd4b94b948c14eeb27a3bbf50ea0f7f0593bad ] The ipg clock only needs to be unprepared in case preparing per clock fails. The ipg clock has already disabled at the point. Fixes: 1cf93e0d5488 ("serial: imx: remove the uart_console() check") Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-21serial: ifx6x60: add missed pm_runtime_disableChuhong Yuan1-0/+3
commit 50b2b571c5f3df721fc81bf9a12c521dfbe019ba upstream. The driver forgets to call pm_runtime_disable in remove. Add the missed calls to fix it. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191118024833.21587-1-hslester96@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-21serial: serial_core: Perform NULL checks for break_ctl opsJiangfeng Xiao1-1/+1
commit 7d73170e1c282576419f8b50a771f1fcd2b81a94 upstream. Doing fuzz test on sbsa uart device, causes a kernel crash due to NULL pointer dereference: ------------[ cut here ]------------ Unable to handle kernel paging request at virtual address fffffffffffffffc pgd = ffffffe331723000 [fffffffffffffffc] *pgd=0000002333595003, *pud=0000002333595003, *pmd=00000 Internal error: Oops: 96000005 [#1] PREEMPT SMP Modules linked in: ping(O) jffs2 rtos_snapshot(O) pramdisk(O) hisi_sfc(O) Drv_Nandc_K(O) Drv_SysCtl_K(O) Drv_SysClk_K(O) bsp_reg(O) hns3(O) hns3_uio_enet(O) hclgevf(O) hclge(O) hnae3(O) mdio_factory(O) mdio_registry(O) mdio_dev(O) mdio(O) hns3_info(O) rtos_kbox_panic(O) uart_suspend(O) rsm(O) stp llc tunnel4 xt_tcpudp ipt_REJECT nf_reject_ipv4 iptable_filter ip_tables x_tables sd_mod xhci_plat_hcd xhci_pci xhci_hcd usbmon usbhid usb_storage ohci_platform ohci_pci ohci_hcd hid_generic hid ehci_platform ehci_pci ehci_hcd vfat fat usbcore usb_common scsi_mod yaffs2multi(O) ext4 jbd2 ext2 mbcache ofpart i2c_dev i2c_core uio ubi nand nand_ecc nand_ids cfi_cmdset_0002 cfi_cmdset_0001 cfi_probe gen_probe cmdlinepart chipreg mtdblock mtd_blkdevs mtd nfsd auth_rpcgss oid_registry nfsv3 nfs nfs_acl lockd sunrpc grace autofs4 CPU: 2 PID: 2385 Comm: tty_fuzz_test Tainted: G O 4.4.193 #1 task: ffffffe32b23f110 task.stack: ffffffe32bda4000 PC is at uart_break_ctl+0x44/0x84 LR is at uart_break_ctl+0x34/0x84 pc : [<ffffff8393196098>] lr : [<ffffff8393196088>] pstate: 80000005 sp : ffffffe32bda7cc0 x29: ffffffe32bda7cc0 x28: ffffffe32b23f110 x27: ffffff8393402000 x26: 0000000000000000 x25: ffffffe32b233f40 x24: ffffffc07a8ec680 x23: 0000000000005425 x22: 00000000ffffffff x21: ffffffe33ed73c98 x20: 0000000000000000 x19: ffffffe33ed94168 x18: 0000000000000004 x17: 0000007f92ae9d30 x16: ffffff8392fa6064 x15: 0000000000000010 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000020 x10: 0000007ffdac1708 x9 : 0000000000000078 x8 : 000000000000001d x7 : 0000000052a64887 x6 : ffffffe32bda7e08 x5 : ffffffe32b23c000 x4 : 0000005fbc5b0000 x3 : ffffff83938d5018 x2 : 0000000000000080 x1 : ffffffe32b23c040 x0 : ffffff83934428f8 virtual start addr offset is 38ac00000 module base offset is 2cd4cf1000 linear region base offset is : 0 Process tty_fuzz_test (pid: 2385, stack limit = 0xffffffe32bda4000) Stack: (0xffffffe32bda7cc0 to 0xffffffe32bda8000) 7cc0: ffffffe32bda7cf0 ffffff8393177718 ffffffc07a8ec680 ffffff8393196054 7ce0: 000000001739f2e0 0000007ffdac1978 ffffffe32bda7d20 ffffff8393179a1c 7d00: 0000000000000000 ffffff8393c0a000 ffffffc07a8ec680 cb88537fdc8ba600 7d20: ffffffe32bda7df0 ffffff8392fa5a40 ffffff8393c0a000 0000000000005425 7d40: 0000007ffdac1978 ffffffe32b233f40 ffffff8393178dcc 0000000000000003 7d60: 000000000000011d 000000000000001d ffffffe32b23f110 000000000000029e 7d80: ffffffe34fe8d5d0 0000000000000000 ffffffe32bda7e14 cb88537fdc8ba600 7da0: ffffffe32bda7e30 ffffff8393042cfc ffffff8393c41720 ffffff8393c46410 7dc0: ffffff839304fa68 ffffffe32b233f40 0000000000005425 0000007ffdac1978 7de0: 000000000000011d cb88537fdc8ba600 ffffffe32bda7e70 ffffff8392fa60cc 7e00: 0000000000000000 ffffffe32b233f40 ffffffe32b233f40 0000000000000003 7e20: 0000000000005425 0000007ffdac1978 ffffffe32bda7e70 ffffff8392fa60b0 7e40: 0000000000000280 ffffffe32b233f40 ffffffe32b233f40 0000000000000003 7e60: 0000000000005425 cb88537fdc8ba600 0000000000000000 ffffff8392e02e78 7e80: 0000000000000280 0000005fbc5b0000 ffffffffffffffff 0000007f92ae9d3c 7ea0: 0000000060000000 0000000000000015 0000000000000003 0000000000005425 7ec0: 0000007ffdac1978 0000000000000000 00000000a54c910e 0000007f92b95014 7ee0: 0000007f92b95090 0000000052a64887 000000000000001d 0000000000000078 7f00: 0000007ffdac1708 0000000000000020 0000000000000000 0000000000000000 7f20: 0000000000000000 0000000000000010 000000556acf0090 0000007f92ae9d30 7f40: 0000000000000004 000000556acdef10 0000000000000000 000000556acdebd0 7f60: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 7f80: 0000000000000000 0000000000000000 0000000000000000 0000007ffdac1840 7fa0: 000000556acdedcc 0000007ffdac1840 0000007f92ae9d3c 0000000060000000 7fc0: 0000000000000000 0000000000000000 0000000000000003 000000000000001d 7fe0: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 Call trace: Exception stack(0xffffffe32bda7ab0 to 0xffffffe32bda7bf0) 7aa0: 0000000000001000 0000007fffffffff 7ac0: ffffffe32bda7cc0 ffffff8393196098 0000000080000005 0000000000000025 7ae0: ffffffe32b233f40 ffffff83930d777c ffffffe32bda7b30 ffffff83930d777c 7b00: ffffffe32bda7be0 ffffff83938d5000 ffffffe32bda7be0 ffffffe32bda7c20 7b20: ffffffe32bda7b60 ffffff83930d777c ffffffe32bda7c10 ffffff83938d5000 7b40: ffffffe32bda7c10 ffffffe32bda7c50 ffffff8393c0a000 ffffffe32b23f110 7b60: ffffffe32bda7b70 ffffff8392e09df4 ffffffe32bda7bb0 cb88537fdc8ba600 7b80: ffffff83934428f8 ffffffe32b23c040 0000000000000080 ffffff83938d5018 7ba0: 0000005fbc5b0000 ffffffe32b23c000 ffffffe32bda7e08 0000000052a64887 7bc0: 000000000000001d 0000000000000078 0000007ffdac1708 0000000000000020 7be0: 0000000000000000 0000000000000000 [<ffffff8393196098>] uart_break_ctl+0x44/0x84 [<ffffff8393177718>] send_break+0xa0/0x114 [<ffffff8393179a1c>] tty_ioctl+0xc50/0xe84 [<ffffff8392fa5a40>] do_vfs_ioctl+0xc4/0x6e8 [<ffffff8392fa60cc>] SyS_ioctl+0x68/0x9c [<ffffff8392e02e78>] __sys_trace_return+0x0/0x4 Code: b9410ea0 34000160 f9408aa0 f9402814 (b85fc280) ---[ end trace 8606094f1960c5e0 ]--- Kernel panic - not syncing: Fatal exception Fix this problem by adding NULL checks prior to calling break_ctl ops. Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1574263133-28259-1-git-send-email-xiaojiangfeng@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-21serial: pl011: Fix DMA ->flush_buffer()Vincent Whitchurch1-4/+2
commit f6a196477184b99a31d16366a8e826558aa11f6d upstream. PL011's ->flush_buffer() implementation releases and reacquires the port lock. Due to a race condition here, data can end up being added to the circular buffer but neither being discarded nor being sent out. This leads to, for example, tcdrain(2) waiting indefinitely. Process A Process B uart_flush_buffer() - acquire lock - circ_clear - pl011_flush_buffer() -- release lock -- dmaengine_terminate_all() uart_write() - acquire lock - add chars to circ buffer - start_tx() -- start DMA - release lock -- acquire lock -- turn off DMA -- release lock // Data in circ buffer but DMA is off According to the comment in the code, the releasing of the lock around dmaengine_terminate_all() is to avoid a deadlock with the DMA engine callback. However, since the time this code was written, the DMA engine API documentation seems to have been clarified to say that dmaengine_terminate_all() (in the identically implemented but differently named dmaengine_terminate_async() variant) does not wait for any running complete callback to be completed and can even be called from a complete callback. So there is no possibility of deadlock if the DMA engine driver implements this API correctly. So we should be able to just remove this release and reacquire of the lock to prevent the aforementioned race condition. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191118092547.32135-1-vincent.whitchurch@axis.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-21tty: serial: msm_serial: Fix flow controlJeffrey Hugo1-1/+5
commit b027ce258369cbfa88401a691c23dad01deb9f9b upstream. hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca disables flow, configures the uart baudrate, and then reenables flow - at which point an event is expected to be received over the uart from the wcn3990. It is observed that this event comes after the baudrate change but before hci_qca re-enables flow. This is unexpected, and is a result of msm_reset() being broken. According to the uart_dm hardware documentation, it is recommended that automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto hw flow control will manage RFR based on the configured watermark. When there is space to receive data, the hw will assert RFR. When the watermark is hit, the hw will de-assert RFR. The hardware documentation indicates that RFR can me manually managed via CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR de-asserts RFR. msm_reset() is broken because after resetting the hardware, it unconditionally asserts RFR via SET_RFR. This enables flow regardless of the current configuration, and would undo a previous flow disable operation. It should instead de-assert RFR via RESET_RFR to block flow until the hardware is reconfigured. msm_serial should rely on the client to specify that flow should be enabled, either via mctrl() or the termios structure, and only assert RFR in response to those triggers. Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: stable <stable@vger.kernel.org> Reviewed-by: Andy Gross <agross@kernel.org> Link: https://lore.kernel.org/r/20191021154616.25457-1-jeffrey.l.hugo@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-21tty: serial: fsl_lpuart: use the sg count from dma_map_sgPeng Fan1-2/+2
commit 487ee861de176090b055eba5b252b56a3b9973d6 upstream. The dmaengine_prep_slave_sg needs to use sg count returned by dma_map_sg, not use sport->dma_tx_nents, because the return value of dma_map_sg is not always same with "nents". When enabling iommu for lpuart + edma, iommu framework may concatenate two sgs into one. Fixes: 6250cc30c4c4e ("tty: serial: fsl_lpuart: Use scatter/gather DMA for Tx") Cc: <stable@vger.kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1572932977-17866-1-git-send-email-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-05serial: max310x: Fix tx_empty() callbackAlexander Shiyan1-5/+2
[ Upstream commit a8da3c7873ea57acb8f9cea58c0af477522965aa ] Function max310x_tx_empty() accesses the IRQSTS register, which is cleared by IC when reading, so if there is an interrupt status, we will lose it. This patch implement the transmitter check only by the current FIFO level. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-25serial: mxs-auart: Fix potential infinite loopAnton Vasilyev1-1/+2
[ Upstream commit 5963e8a3122471cadfe0eba41c4ceaeaa5c8bb4d ] On the error path of mxs_auart_request_gpio_irq() is performed backward iterating with index i of enum type. Underline enum type may be unsigned char. In this case check (--i >= 0) will be always true and error handling goes into infinite loop. The patch changes the check so that it is valid for signed and unsigned types. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-06serial: mctrl_gpio: Check for NULL pointerAdam Ford1-0/+3
[ Upstream commit 37e3ab00e4734acc15d96b2926aab55c894f4d9c ] When using mctrl_gpio_to_gpiod, it dereferences gpios into a single requested GPIO. This dereferencing can break if gpios is NULL, so this patch adds a NULL check before dereferencing it. If gpios is NULL, this function will also return NULL. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com> Link: https://lore.kernel.org/r/20191006163314.23191-1-aford173@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-06sc16is7xx: Fix for "Unexpected interrupt: 8"Phil Elwell1-0/+28
[ Upstream commit 30ec514d440cf2c472c8e4b0079af2c731f71a3e ] The SC16IS752 has an Enhanced Feature Register which is aliased at the same address as the Interrupt Identification Register; accessing it requires that a magic value is written to the Line Configuration Register. If an interrupt is raised while the EFR is mapped in then the ISR won't be able to access the IIR, leading to the "Unexpected interrupt" error messages. Avoid the problem by claiming a mutex around accesses to the EFR register, also claiming the mutex in the interrupt handler work item (this is equivalent to disabling interrupts to interlock against a non-threaded interrupt handler). See: https://github.com/raspberrypi/linux/issues/2529 Signed-off-by: Phil Elwell <phil@raspberrypi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-10-17serial: uartlite: fix exit path null pointerRandy Dunlap1-1/+2
commit a553add0846f355a28ed4e81134012e4a1e280c2 upstream. Call uart_unregister_driver() conditionally instead of unconditionally, only if it has been previously registered. This uses driver.state, just as the sh-sci.c driver does. Fixes this null pointer dereference in tty_unregister_driver(), since the 'driver' argument is null: general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI RIP: 0010:tty_unregister_driver+0x25/0x1d0 Fixes: 238b8721a554 ("[PATCH] serial uartlite driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: stable <stable@vger.kernel.org> Cc: Peter Korsgaard <jacmet@sunsite.dk> Link: https://lore.kernel.org/r/9c8e6581-6fcc-a595-0897-4d90f5d710df@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-21tty/serial: atmel: reschedule TX after RX was startedRazvan Stefanescu1-1/+0
commit d2ace81bf902a9f11d52e59e5d232d2255a0e353 upstream. When half-duplex RS485 communication is used, after RX is started, TX tasklet still needs to be scheduled tasklet. This avoids console freezing when more data is to be transmitted, if the serial communication is not closed. Fixes: 69646d7a3689 ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped") Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190813074025.16218-1-razvan.stefanescu@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-21serial: sprd: correct the wrong sequence of argumentsChunyan Zhang1-1/+1
commit 9c801e313195addaf11c16e155f50789d6ebfd19 upstream. The sequence of arguments which was passed to handle_lsr_errors() didn't match the parameters defined in that function, &lsr was passed to flag and &flag was passed to lsr, this patch fixed that. Fixes: b7396a38fb28 ("tty/serial: Add Spreadtrum sc9836-uart driver support") Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com> Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190905074151.5268-1-zhang.lyra@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-04serial: sh-sci: Fix TX DMA buffer flushing and workqueue racesGeert Uytterhoeven1-7/+15
[ Upstream commit 8493eab02608b0e82f67b892aa72882e510c31d0 ] When uart_flush_buffer() is called, the .flush_buffer() callback zeroes the tx_dma_len field. This may race with the work queue function handling transmit DMA requests: 1. If the buffer is flushed before the first DMA API call, dmaengine_prep_slave_single() may be called with a zero length, causing the DMA request to never complete, leading to messages like: rcar-dmac e7300000.dma-controller: Channel Address Error happen and, with debug enabled: sh-sci e6e88000.serial: sci_dma_tx_work_fn: ffff800639b55000: 0...0, cookie 126 and DMA timeouts. 2. If the buffer is flushed after the first DMA API call, but before the second, dma_sync_single_for_device() may be called with a zero length, causing the transmit data not to be flushed to RAM, and leading to stale data being output. Fix this by: 1. Letting sci_dma_tx_work_fn() return immediately if the transmit buffer is empty, 2. Extending the critical section to cover all DMA preparational work, so tx_dma_len stays consistent for all of it, 3. Using local copies of circ_buf.head and circ_buf.tail, to make sure they match the actual operation above. Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com> Suggested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com> Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com> Link: https://lore.kernel.org/r/20190624123540.20629-2-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-04serial: sh-sci: Terminate TX DMA during buffer flushingGeert Uytterhoeven1-2/+9
[ Upstream commit 775b7ffd7d6d5db320d99b0a485c51e04dfcf9f1 ] While the .flush_buffer() callback clears sci_port.tx_dma_len since commit 1cf4a7efdc71cab8 ("serial: sh-sci: Fix race condition causing garbage during shutdown"), it does not terminate a transmit DMA operation that may be in progress. Fix this by terminating any pending DMA operations, and resetting the corresponding cookie. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com> Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com> Link: https://lore.kernel.org/r/20190624123540.20629-3-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-04tty: serial_core: Set port active bit in uart_port_activateSerge Semin1-1/+6
[ Upstream commit 13b18d35909707571af9539f7731389fbf0feb31 ] A bug was introduced by commit b3b576461864 ("tty: serial_core: convert uart_open to use tty_port_open"). It caused a constant warning printed into the system log regarding the tty and port counter mismatch: [ 21.644197] ttyS ttySx: tty_port_close_start: tty->count = 1 port count = 2 in case if session hangup was detected so the warning is printed starting from the second open-close iteration. Particularly the problem was discovered in situation when there is a serial tty device without hardware back-end being setup. It is considered by the tty-serial subsystems as a hardware problem with session hang up. In this case uart_startup() will return a positive value with TTY_IO_ERROR flag set in corresponding tty_struct instance. The same value will get passed to be returned from the activate() callback and then being returned from tty_port_open(). But since in this case tty_port_block_til_ready() isn't called the TTY_PORT_ACTIVE flag isn't set (while the method had been called before tty_port_open conversion was introduced and the rest of the subsystem code expected the bit being set in this case), which prevents the uart_hangup() method to perform any cleanups including the tty port counter setting to zero. So the next attempt to open/close the tty device will discover the counters mismatch. In order to fix the problem we need to manually set the TTY_PORT_ACTIVE flag in case if uart_startup() returned a positive value. In this case the hang up procedure will perform a full set of cleanup actions including the port ref-counter resetting. Fixes: b3b576461864 "tty: serial_core: convert uart_open to use tty_port_open" Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-04serial: 8250: Fix TX interrupt handling conditionRautkoski Kimmo EXT1-1/+2
[ Upstream commit db1b5bc047b3cadaedab3826bba82c3d9e023c4b ] Interrupt handler checked THRE bit (transmitter holding register empty) in LSR to detect if TX fifo is empty. In case when there is only receive interrupts the TX handling got called because THRE bit in LSR is set when there is no transmission (FIFO empty). TX handling caused TX stop, which in RS-485 half-duplex mode actually resets receiver FIFO. This is not desired during reception because of possible data loss. The fix is to check if THRI is set in IER in addition of the TX fifo status. THRI in IER is set when TX is started and cleared when TX is stopped. This ensures that TX handling is only called when there is really transmission on going and an interrupt for THRE and not when there are only RX interrupts. Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-04tty: serial: msm_serial: avoid system lockup conditionJorge Ramirez-Ortiz1-0/+4
[ Upstream commit ba3684f99f1b25d2a30b6956d02d339d7acb9799 ] The function msm_wait_for_xmitr can be taken with interrupts disabled. In order to avoid a potential system lockup - demonstrated under stress testing conditions on SoC QCS404/5 - make sure we wait for a bounded amount of time. Tested on SoC QCS404. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-04tty/serial: digicolor: Fix digicolor-usart already registered warningKefeng Wang1-1/+5
[ Upstream commit c7ad9ba0611c53cfe194223db02e3bca015f0674 ] When modprobe/rmmod/modprobe module, if platform_driver_register() fails, the kernel complained, proc_dir_entry 'driver/digicolor-usart' already registered WARNING: CPU: 1 PID: 5636 at fs/proc/generic.c:360 proc_register+0x19d/0x270 Fix this by adding uart_unregister_driver() when platform_driver_register() fails. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-04tty: serial: cpm_uart - fix init when SMC is relocatedChristophe Leroy1-6/+11
[ Upstream commit 06aaa3d066db87e8478522d910285141d44b1e58 ] SMC relocation can also be activated earlier by the bootloader, so the driver's behaviour cannot rely on selected kernel config. When the SMC is relocated, CPM_CR_INIT_TRX cannot be used. But the only thing CPM_CR_INIT_TRX does is to clear the rstate and tstate registers, so this can be done manually, even when SMC is not relocated. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Fixes: 9ab921201444 ("cpm_uart: fix non-console port startup bug") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>