summaryrefslogtreecommitdiff
path: root/drivers/tty/serial
AgeCommit message (Collapse)AuthorFilesLines
2020-12-21serial: 8250_omap: Avoid FIFO corruption caused by MDR1 accessAlexander Sverdlin1-5/+0
commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream. It has been observed that once per 300-1300 port openings the first transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared as "e" on the wire). It only happened if single byte has been transmitted right after port open, which means, DMA is not used for this transfer and the corruption never happened afterwards. Therefore I've carefully re-read the MDR1 errata (link below), which says "when accessing the MDR1 registers that causes a dummy under-run condition that will freeze the UART in IrDA transmission. In UART mode, this may corrupt the transferred data". Strictly speaking, omap_8250_mdr1_errataset() performs a read access and if the value is the same as should be written, exits without errata-recommended FIFO reset. A brief check of the serial_omap_mdr1_errataset() from the competing omap-serial driver showed it has no read access of MDR1. After removing the read access from omap_8250_mdr1_errataset() the data corruption never happened any more. Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver") Cc: stable@vger.kernel.org Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-24serial: ar933x_uart: disable clk on error handling path in probeZheng Zengkai1-2/+4
commit 425af483523b76bc78e14674a430579d38b2a593 upstream. ar933x_uart_probe() does not invoke clk_disable_unprepare() on one error handling path. This patch fixes that. Fixes: 9be1064fe524 ("serial: ar933x_uart: add RS485 support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com> Link: https://lore.kernel.org/r/20201111124426.42638-1-zhengzengkai@huawei.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-24tty: serial: imx: keep console clocks always onFugang Duan1-17/+3
commit e67c139c488e84e7eae6c333231e791f0e89b3fb upstream. For below code, there has chance to cause deadlock in SMP system: Thread 1: clk_enable_lock(); pr_info("debug message"); clk_enable_unlock(); Thread 2: imx_uart_console_write() clk_enable() clk_enable_lock(); Thread 1: Acuired clk enable_lock -> printk -> console_trylock_spinning Thread 2: console_unlock() -> imx_uart_console_write -> clk_disable -> Acquite clk enable_lock So the patch is to keep console port clocks always on like other console drivers. Fixes: 1cf93e0d5488 ("serial: imx: remove the uart_console() check") Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20201111025136.29818-1-fugang.duan@nxp.com Cc: stable <stable@vger.kernel.org> [fix up build warning - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-24tty: serial: imx: fix potential deadlockSam Nobs1-2/+8
commit 33f16855dcb973f745c51882d0e286601ff3be2b upstream. Enabling the lock dependency validator has revealed that the way spinlocks are used in the IMX serial port could result in a deadlock. Specifically, imx_uart_int() acquires a spinlock without disabling the interrupts, meaning that another interrupt could come along and try to acquire the same spinlock, potentially causing the two to wait for each other indefinitely. Use spin_lock_irqsave() instead to disable interrupts upon acquisition of the spinlock. Fixes: c974991d2620 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com> Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10serial: txx9: add missing platform_driver_unregister() on error in ↵Qinglang Miao1-0/+3
serial_txx9_init commit 0c5fc92622ed5531ff324b20f014e9e3092f0187 upstream. Add the missing platform_driver_unregister() before return from serial_txx9_init in the error handling case when failed to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI defined. Fixes: ab4382d27412 ("tty: move drivers/serial/ to drivers/tty/serial/") Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10serial: 8250_mtk: Fix uart_get_baud_rate warningClaire Chang1-1/+1
commit 912ab37c798770f21b182d656937072b58553378 upstream. Mediatek 8250 port supports speed higher than uartclk / 16. If the baud rates in both the new and the old termios setting are higher than uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered. Passing NULL as the old termios so uart_get_baud_rate() will use uartclk / 16 - 1 as the new baud rate which will be replaced by the original baud rate later by tty_termios_encode_baud_rate() in mtk8250_set_termios(). Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping") Signed-off-by: Claire Chang <tientzu@chromium.org> Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10tty: serial: imx: enable earlycon by default if IMX_SERIAL_CONSOLE is enabledLucas Stach1-0/+1
commit 427627a23c3e86e31113f9db9bfdca41698a0ee5 upstream. Since 699cc4dfd140 (tty: serial: imx: add imx earlycon driver), the earlycon part of imx serial is a separate driver and isn't necessarily enabled anymore when the console is enabled. This causes users to loose the earlycon functionality when upgrading their kenrel configuration via oldconfig. Enable earlycon by default when IMX_SERIAL_CONSOLE is enabled. Fixes: 699cc4dfd140 (tty: serial: imx: add imx earlycon driver) Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Link: https://lore.kernel.org/r/20201105204026.1818219-1-l.stach@pengutronix.de Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-05tty: serial: fsl_lpuart: LS1021A has a FIFO size of 16 words, like LS1028AVladimir Oltean1-6/+7
commit c97f2a6fb3dfbfbbc88edc8ea62ef2b944e18849 upstream. Prior to the commit that this one fixes, the FIFO size was derived from the read-only register LPUARTx_FIFO[TXFIFOSIZE] using the following formula: TX FIFO size = 2 ^ (LPUARTx_FIFO[TXFIFOSIZE] - 1) The documentation for LS1021A is a mess. Under chapter 26.1.3 LS1021A LPUART module special consideration, it mentions TXFIFO_SZ and RXFIFO_SZ being equal to 4, and in the register description for LPUARTx_FIFO, it shows the out-of-reset value of TXFIFOSIZE and RXFIFOSIZE fields as "011", even though these registers read as "101" in reality. And when LPUART on LS1021A was working, the "101" value did correspond to "16 datawords", by applying the formula above, even though the documentation is wrong again (!!!!) and says that "101" means 64 datawords (hint: it doesn't). So the "new" formula created by commit f77ebb241ce0 has all the premises of being wrong for LS1021A, because it relied only on false data and no actual experimentation. Interestingly, in commit c2f448cff22a ("tty: serial: fsl_lpuart: add LS1028A support"), Michael Walle applied a workaround to this by manually setting the FIFO widths for LS1028A. It looks like the same values are used by LS1021A as well, in fact. When the driver thinks that it has a deeper FIFO than it really has, getty (user space) output gets truncated. Many thanks to Michael for pointing out where to look. Fixes: f77ebb241ce0 ("tty: serial: fsl_lpuart: correct the FIFO depth size") Suggested-by: Michael Walle <michael@walle.cc> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20201023013429.3551026-1-vladimir.oltean@nxp.com Reviewed-by：Fugang Duan <fugang.duan@nxp.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-05tty: serial: 21285: fix lockup on openRussell King1-6/+6
commit 82776f6c75a90e1d2103e689b84a689de8f1aa02 upstream. Commit 293f89959483 ("tty: serial: 21285: stop using the unused[] variable from struct uart_port") introduced a bug which stops the transmit interrupt being disabled when there are no characters to transmit - disabling the transmit interrupt at the interrupt controller is the only way to stop an interrupt storm. If this interrupt is not disabled when there are no transmit characters, we end up with an interrupt storm which prevents the machine making forward progress. Fixes: 293f89959483 ("tty: serial: 21285: stop using the unused[] variable from struct uart_port") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/E1kU4GS-0006lE-OO@rmk-PC.armlinux.org.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-01serial: pl011: Fix lockdep splat when handling magic-sysrq interruptPeter Zijlstra1-4/+7
commit 534cf755d9df99e214ddbe26b91cd4d81d2603e2 upstream. Issuing a magic-sysrq via the PL011 causes the following lockdep splat, which is easily reproducible under QEMU: | sysrq: Changing Loglevel | sysrq: Loglevel set to 9 | | ====================================================== | WARNING: possible circular locking dependency detected | 5.9.0-rc7 #1 Not tainted | ------------------------------------------------------ | systemd-journal/138 is trying to acquire lock: | ffffab133ad950c0 (console_owner){-.-.}-{0:0}, at: console_lock_spinning_enable+0x34/0x70 | | but task is already holding lock: | ffff0001fd47b098 (&port_lock_key){-.-.}-{2:2}, at: pl011_int+0x40/0x488 | | which lock already depends on the new lock. [...] | Possible unsafe locking scenario: | | CPU0 CPU1 | ---- ---- | lock(&port_lock_key); | lock(console_owner); | lock(&port_lock_key); | lock(console_owner); | | *** DEADLOCK *** The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int() before taking 'console_owner' on the printk() path, whereas CPU1 takes the two locks in the opposite order on the printk() path due to setting the "console_owner" prior to calling into into the actual console driver. Fix this in the same way as the msm-serial driver by dropping 'port_lock' before handling the sysrq. Cc: <stable@vger.kernel.org> # 4.19+ Cc: Russell King <linux@armlinux.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck Signed-off-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Will Deacon <will@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-01serial: qcom_geni_serial: To correct QUP Version detection logicParas Sharma1-1/+1
commit c9ca43d42ed8d5fd635d327a664ed1d8579eb2af upstream. For QUP IP versions 2.5 and above the oversampling rate is halved from 32 to 16. Commit ce734600545f ("tty: serial: qcom_geni_serial: Update the oversampling rate") is pushed to handle this scenario. But the existing logic is failing to classify QUP Version 3.0 into the correct group ( 2.5 and above). As result Serial Engine clocks are not configured properly for baud rate and garbage data is sampled to FIFOs from the line. So, fix the logic to detect QUP with versions 2.5 and above. Fixes: ce734600545f ("tty: serial: qcom_geni_serial: Update the oversampling rate") Cc: stable <stable@vger.kernel.org> Signed-off-by: Paras Sharma <parashar@codeaurora.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Link: https://lore.kernel.org/r/1601445926-23673-1-git-send-email-parashar@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-29tty: serial: fsl_lpuart: fix lpuart32_poll_get_charPeng Fan1-1/+1
commit 29788ab1d2bf26c130de8f44f9553ee78a27e8d5 upstream. The watermark is set to 1, so we need to input two chars to trigger RDRF using the original logic. With the new logic, we could always get the char when there is data in FIFO. Suggested-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-29tty: serial: lpuart: fix lpuart32_write usagePeng Fan1-8/+6
commit 9ea40db477c024dcb87321b7f32bd6ea12130ac2 upstream. The 2nd and 3rd parameter were wrongly used, and cause kernel abort when doing kgdb debug. Fixes: 1da17d7cf8e2 ("tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs") Cc: stable <stable@vger.kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/20200929091920.22612-1-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-29serial: 8250_dw: Fix clk-notifier/port suspend deadlockSerge Semin1-35/+19
[ Upstream commit 85985a3dcd7415dd849cf62ec14f931cd905099a ] It has been discovered that there is a potential deadlock between the clock-change-notifier thread and the UART port suspending one: CPU0 (suspend CPU/UART) CPU1 (update clock) ---- ---- lock(&port->mutex); lock((work_completion)(&data->clk_work)); lock(&port->mutex); lock((work_completion)(&data->clk_work)); *** DEADLOCK *** The best way to fix this is to eliminate the CPU0 port->mutex/work-completion scenario. So we suggest to register and unregister the clock-notifier during the DW APB UART port probe/remove procedures, instead of doing that at the points of the port startup/shutdown. Link: https://lore.kernel.org/linux-serial/f1cd5c75-9cda-6896-a4e2-42c5bfc3f5c3@redhat.com Fixes: cc816969d7b5 ("serial: 8250_dw: Fix common clocks usage race condition") Reported-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200923161950.6237-4-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-29serial: 8250: Skip uninitialized TTY port baud rate updateSerge Semin1-0/+4
[ Upstream commit c8dff3aa824177013d90967687f09f713a55d13f ] It is erroneous to update the TTY port baud rate if it hasn't been initialized yet, because in that case the TTY struct isn't set. So there is no termios structure to get and re-calculate the baud if the current baud can't be reached. Let's skip the baud rate update then until the port is fully initialized. Note the update UART clock method still sets the uartclk member with a new ref clock value even if the port is turned off. The new UART ref clock rate will be used later on the port starting up procedure. Fixes: 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method") Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200923161950.6237-3-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-29serial: 8250: Discard RTS/DTS setting from clock update methodSerge Semin1-1/+0
[ Upstream commit 7718453e36960dadb8dc46f2b514b309659e1270 ] It has been a mistake to add the MCR register RTS/DTS fields setting in the generic method of the UART reference clock update. There is no point in asserting these lines at that procedure. Just discard the serial8250_out_MCR() mathod invocation from there then. Fixes: 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method") Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200923161950.6237-2-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-29tty: serial: imx: fix link error with CONFIG_SERIAL_CORE_CONSOLE=nYang Yingliang1-0/+1
[ Upstream commit 24c796926e2f88b383a76ddc871a7cdd62484f3a ] aarch64-linux-gnu-ld: drivers/tty/serial/imx_earlycon.o: in function `imx_uart_console_early_write': imx_earlycon.c:(.text+0x84): undefined reference to `uart_console_write' The driver uses the uart_console_write(), but SERIAL_CORE_CONSOLE is not selected, so uart_console_write is not defined, then we get the error. Fix this by selecting SERIAL_CORE_CONSOLE. Fixes: 699cc4dfd140 ("tty: serial: imx: add imx earlycon driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20200919063240.2754965-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-29tty: serial: earlycon dependencyTong Zhang1-0/+1
[ Upstream commit 0fb9342d06b0f667b915ba58bfefc030e534a218 ] parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON should automatically select SERIAL_CORE, otherwise will result in symbol not found error during linking if SERIAL_CORE is not configured as builtin Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon") Signed-off-by: Tong Zhang <ztong0001@gmail.com> Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-09-16serial: 8250_pci: Add Realtek 816a and 816bTobias Diedrich1-0/+11
These serial ports are exposed by the OOB-management-engine on RealManage-enabled network cards (e.g. AMD DASH enabled systems using Realtek cards). Because these have 3 BARs, they fail the "num_iomem <= 1" check in serial_pci_guess_board. I've manually checked the two IOMEM regions and BAR 2 doesn't seem to respond to reads, but BAR 4 seems to be an MMIO version of the IO ports (untested). With this change, the ports are detected: 0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A 0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A lspci output: 02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550]) Subsystem: 17aa:5082 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 82 IOMMU group: 11 Region 0: I/O ports at 2200 [size=256] Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s (ok), Width x1 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp- ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data Not readable Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [170 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [178 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=150us PortTPowerOnTime=150us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us 02:00.2 0700: 10ec:816b (rev 0e) [...same...] Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: core: fix console port-lock regressionJohan Hovold1-17/+15
Fix the port-lock initialisation regression introduced by commit a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") by making sure that the lock is again initialised during console setup. The console may be registered before the serial controller has been probed in which case the port lock needs to be initialised during console setup by a call to uart_set_options(). The console-detach changes introduced a regression in several drivers by effectively removing that initialisation by not initialising the lock when the port is used as a console (which is always the case during console setup). Add back the early lock initialisation and instead use a new console-reinit flag to handle the case where a console is being re-attached through sysfs. The question whether the console-detach interface should have been added in the first place is left for another discussion. Note that the console-enabled check in uart_set_options() is not redundant because of kgdboc, which can end up reinitialising an already enabled console (see commit 42b6a1baa3ec ("serial_core: Don't re-initialize a previously initialized spinlock.")). Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") Cc: stable <stable@vger.kernel.org> # 5.7 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200909143101.15389-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: core: fix port-lock initialisationJohan Hovold1-8/+6
Commit f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()") tried to work around a breakage introduced by commit a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") by adding a second initialisation of the port lock when registering the port. As reported by the build robots [1], this doesn't really solve the regression introduced by the console-detach changes and also adds a second redundant initialisation of the lock for normal ports. Start cleaning up this mess by removing the redundant initialisation and making sure that the port lock is again initialised once-only for ports that aren't already in use as a console. [1] https://lore.kernel.org/r/20200802054852.GR23458@shao2-debian Fixes: f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()") Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") Cc: stable <stable@vger.kernel.org> # 5.7 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200909143101.15389-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-26Merge tag 'tty-5.9-rc3' of ↵Linus Torvalds8-20/+52
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial fixes from Greg KH: "Here are a few small TTY/Serial/vt fixes for 5.9-rc3 Included in here are: - qcom serial fixes - vt ioctl and core bugfixes - pl011 serial driver fixes - 8250 serial driver fixes - other misc serial driver fixes and for good measure: - fbcon fix for syzbot found problem. All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: tty: serial: imx: add dependence and build for earlycon serial: samsung: Removes the IRQ not found warning serial: 8250: change lock order in serial8250_do_startup() serial: stm32: avoid kernel warning on absence of optional IRQ serial: pl011: Fix oops on -EPROBE_DEFER serial: pl011: Don't leak amba_ports entry on driver register error serial: 8250_exar: Fix number of ports for Commtech PCIe cards tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setup serial: qcom_geni_serial: Fix recent kdb hang vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize() fbcon: prevent user font height or width change from causing potential out-of-bounds access vt: defer kfree() of vc_screenbuf in vc_do_resize()
2020-08-24treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva13-16/+14
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-18tty: serial: imx: add dependence and build for earlyconFugang Duan2-0/+2
Add the earlycon dependence and add earlycon Makefile support to allow to build the driver. Fixes: 699cc4dfd140 ("tty: serial: imx: add imx earlycon driver") Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20200810060652.3436-1-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: samsung: Removes the IRQ not found warningTamseel Shams1-3/+5
In few older Samsung SoCs like s3c2410, s3c2412 and s3c2440, UART IP is having 2 interrupt lines. However, in other SoCs like s3c6400, s5pv210, exynos5433, and exynos4210 UART is having only 1 interrupt line. Due to this, "platform_get_irq(platdev, 1)" call in the driver gives the following false-positive error: "IRQ index 1 not found" on newer SoC's. This patch adds the condition to check for Tx interrupt only for the those SoC's which have 2 interrupt lines. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Tamseel Shams <m.shams@samsung.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: 8250: change lock order in serial8250_do_startup()Sergey Senozhatsky1-3/+6
We have a number of "uart.port->desc.lock vs desc.lock->uart.port" lockdep reports coming from 8250 driver; this causes a bit of trouble to people, so let's fix it. The problem is reverse lock order in two different call paths: chain #1: serial8250_do_startup() spin_lock_irqsave(&port->lock); disable_irq_nosync(port->irq); raw_spin_lock_irqsave(&desc->lock) chain #2: __report_bad_irq() raw_spin_lock_irqsave(&desc->lock) for_each_action_of_desc() printk() spin_lock_irqsave(&port->lock); Fix this by changing the order of locks in serial8250_do_startup(): do disable_irq_nosync() first, which grabs desc->lock, and grab uart->port after that, so that chain #1 and chain #2 have same lock order. Full lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.4.39 #55 Not tainted ====================================================== swapper/0/0 is trying to acquire lock: ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57 but task is already holding lock: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&irq_desc_lock_class){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d __irq_get_desc_lock+0x65/0x89 __disable_irq_nosync+0x3b/0x93 serial8250_do_startup+0x451/0x75c uart_startup+0x1b4/0x2ff uart_port_activate+0x73/0xa0 tty_port_open+0xae/0x10a uart_open+0x1b/0x26 tty_open+0x24d/0x3a0 chrdev_open+0xd5/0x1cc do_dentry_open+0x299/0x3c8 path_openat+0x434/0x1100 do_filp_open+0x9b/0x10a do_sys_open+0x15f/0x3d7 kernel_init_freeable+0x157/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #1 (&port_lock_key){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d serial8250_console_write+0xa7/0x2a0 console_unlock+0x3b7/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 register_console+0x336/0x3a4 uart_add_one_port+0x51b/0x5be serial8250_register_8250_port+0x454/0x55e dw8250_probe+0x4dc/0x5b9 platform_drv_probe+0x67/0x8b really_probe+0x14a/0x422 driver_probe_device+0x66/0x130 device_driver_attach+0x42/0x5b __driver_attach+0xca/0x139 bus_for_each_dev+0x97/0xc9 bus_add_driver+0x12b/0x228 driver_register+0x64/0xed do_one_initcall+0x20c/0x4a6 do_initcall_level+0xb5/0xc5 do_basic_setup+0x4c/0x58 kernel_init_freeable+0x13f/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #0 (console_owner){-...}: __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 console_lock_spinning_enable+0x51/0x57 console_unlock+0x25d/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 ret_from_intr+0x0/0x1d cpuidle_enter_state+0x12f/0x1fd cpuidle_enter+0x2e/0x3d do_idle+0x1ce/0x2ce cpu_startup_entry+0x1d/0x1f start_kernel+0x406/0x46a secondary_startup_64+0xa4/0xb0 other info that might help us debug this: Chain exists of: console_owner --> &port_lock_key --> &irq_desc_lock_class Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&irq_desc_lock_class); lock(&port_lock_key); lock(&irq_desc_lock_class); lock(console_owner); *** DEADLOCK *** 2 locks held by swapper/0/0: #0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba #1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55 Hardware name: XXXXXX Call Trace: <IRQ> dump_stack+0xbf/0x133 ? print_circular_bug+0xd6/0xe9 check_noncircular+0x1b9/0x1c3 __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 ? console_lock_spinning_enable+0x31/0x57 console_lock_spinning_enable+0x51/0x57 ? console_lock_spinning_enable+0x31/0x57 console_unlock+0x25d/0x528 ? console_trylock+0x18/0x4e vprintk_emit+0x111/0x17f ? lock_acquire+0x203/0x258 printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 common_interrupt+0xf/0xf </IRQ> Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels") Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: Raul Rangel <rrangel@google.com> BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800 Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: stm32: avoid kernel warning on absence of optional IRQHolger Assmann1-1/+1
stm32_init_port() of the stm32-usart may trigger a warning in platform_get_irq() when the device tree specifies no wakeup interrupt. The wakeup interrupt is usually a board-specific GPIO and the driver functions correctly in its absence. The mainline stm32mp151.dtsi does not specify it, so all mainline device trees trigger an unnecessary kernel warning. Use of platform_get_irq_optional() avoids this. Fixes: 2c58e56096dd ("serial: stm32: fix the get_irq error case") Signed-off-by: Holger Assmann <h.assmann@pengutronix.de> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: pl011: Fix oops on -EPROBE_DEFERLukas Wunner1-6/+5
If probing of a pl011 gets deferred until after free_initmem(), an oops ensues because pl011_console_match() is called which has been freed. Fix by removing the __init attribute from the function and those it calls. Commit 10879ae5f12e ("serial: pl011: add console matching function") introduced pl011_console_match() not just for early consoles but regular preferred consoles, such as those added by acpi_parse_spcr(). Regular consoles may be registered after free_initmem() for various reasons, one being deferred probing, another being dynamic enablement of serial ports using a DeviceTree overlay. Thus, pl011_console_match() must not be declared __init and the functions it calls mustn't either. Stack trace for posterity: Unable to handle kernel paging request at virtual address 80c38b58 Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM PC is at pl011_console_match+0x0/0xfc LR is at register_console+0x150/0x468 [<80187004>] (register_console) [<805a8184>] (uart_add_one_port) [<805b2b68>] (pl011_register_port) [<805b3ce4>] (pl011_probe) [<80569214>] (amba_probe) [<805ca088>] (really_probe) [<805ca2ec>] (driver_probe_device) [<805ca5b0>] (__device_attach_driver) [<805c8060>] (bus_for_each_drv) [<805c9dfc>] (__device_attach) [<805ca630>] (device_initial_probe) [<805c90a8>] (bus_probe_device) [<805c95a8>] (deferred_probe_work_func) Fixes: 10879ae5f12e ("serial: pl011: add console matching function") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.10+ Cc: Aleksey Makarov <amakarov@marvell.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Christopher Covington <cov@codeaurora.org> Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: pl011: Don't leak amba_ports entry on driver register errorLukas Wunner1-1/+4
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry, then calls pl011_register_port() to register the uart driver with the tty layer. If registration of the uart driver fails, the amba_ports[] entry is not released. If this happens 14 times (value of UART_NR macro), then all amba_ports[] entries will have been leaked and driver probing is no longer possible. (To be fair, that can only happen if the DeviceTree doesn't contain alias IDs since they cause the same entry to be used for a given port.) Fix it. Fixes: ef2889f7ffee ("serial: pl011: Move uart_register_driver call to device") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v3.15+ Cc: Tushar Behera <tushar.behera@linaro.org> Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: 8250_exar: Fix number of ports for Commtech PCIe cardsValmer Huhn1-3/+21
The following in 8250_exar.c line 589 is used to determine the number of ports for each Exar board: nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f; If the number of ports a card has is not explicitly specified, it defaults to the rightmost 4 bits of the PCI device ID. This is prone to error since not all PCI device IDs contain a number which corresponds to the number of ports that card provides. This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021. Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and 8 ports respectively. To fix this, each Commtech Fastcom PCIe card is given a struct where the number of ports is explicitly specified. This ensures 'board->num_ports' is used instead of the default 'pcidev->device & 0x0f'. Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci") Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setupJohn Stultz1-1/+1
When booting with heavily modularized config, the serial console may not be able to load until after init when modules that satisfy needed dependencies have time to load. Unfortunately, as qcom_geni_console_setup is marked as __init, the function may have been freed before we get to run it, causing boot time crashes such as: [ 6.469057] Unable to handle kernel paging request at virtual address ffffffe645d4e6cc [ 6.481623] Mem abort info: [ 6.484466] ESR = 0x86000007 [ 6.487557] EC = 0x21: IABT (current EL), IL = 32 bits [ 6.492929] SET = 0, FnV = 0g [ 6.496016] EA = 0, S1PTW = 0 [ 6.499202] swapper pgtable: 4k pages, 39-bit VAs, pgdp=000000008151e000 [ 6.501286] ufshcd-qcom 1d84000.ufshc: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2 [ 6.505977] [ffffffe645d4e6cc] pgd=000000017df9f003, p4d=000000017df9f003, pud=000000017df9f003, pmd=000000017df9c003, pte=0000000000000000 [ 6.505990] Internal error: Oops: 86000007 [#1] PREEMPT SMP [ 6.505995] Modules linked in: zl10353 zl10039 zl10036 zd1301_demod xc5000 xc4000 ves1x93 ves1820 tuner_xc2028 tuner_simple tuner_types tua9001 tua6100 1 [ 6.506152] isl6405 [ 6.518104] ufshcd-qcom 1d84000.ufshc: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0 [ 6.530549] horus3a helene fc2580 fc0013 fc0012 fc0011 ec100 e4000 dvb_pll ds3000 drxk drxd drx39xyj dib9000 dib8000 dib7000p dib7000m dib3000mc dibx003 [ 6.624271] CPU: 7 PID: 148 Comm: kworker/7:2 Tainted: G W 5.8.0-mainline-12021-g6defd37ba1cd #3455 [ 6.624273] Hardware name: Thundercomm Dragonboard 845c (DT) [ 6.624290] Workqueue: events deferred_probe_work_func [ 6.624296] pstate: 40c00005 (nZcv daif +PAN +UAO BTYPE=--) [ 6.624307] pc : qcom_geni_console_setup+0x0/0x110 [ 6.624316] lr : try_enable_new_console+0xa0/0x140 [ 6.624318] sp : ffffffc010843a30 [ 6.624320] x29: ffffffc010843a30 x28: ffffffe645c3e7d0 [ 6.624325] x27: ffffff80f8022180 x26: ffffffc010843b28 [ 6.637937] x25: 0000000000000000 x24: ffffffe6462a2000 [ 6.637941] x23: ffffffe646398000 x22: 0000000000000000 [ 6.637945] x21: 0000000000000000 x20: ffffffe6462a5ce8 [ 6.637952] x19: ffffffe646398e38 x18: ffffffffffffffff [ 6.680296] x17: 0000000000000000 x16: ffffffe64492b900 [ 6.680300] x15: ffffffe6461e9d08 x14: 69202930203d2064 [ 6.680305] x13: 7561625f65736162 x12: 202c363331203d20 [ 6.696434] x11: 0000000000000030 x10: 0101010101010101 [ 6.696438] x9 : 4d4d20746120304d x8 : 7f7f7f7f7f7f7f7f [ 6.707249] x7 : feff4c524c787373 x6 : 0000000000008080 [ 6.707253] x5 : 0000000000000000 x4 : 8080000000000000 [ 6.707257] x3 : 0000000000000000 x2 : ffffffe645d4e6cc [ 6.744223] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34) [ 6.744966] x1 : fffffffefe74e174 x0 : ffffffe6462a5ce8 [ 6.753580] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34) [ 6.761634] Call trace: [ 6.761639] qcom_geni_console_setup+0x0/0x110 [ 6.761645] register_console+0x29c/0x2f8 [ 6.767981] Bluetooth: hci0: Frame reassembly failed (-84) [ 6.775252] uart_add_one_port+0x438/0x500 [ 6.775258] qcom_geni_serial_probe+0x2c4/0x4a8 [ 6.775266] platform_drv_probe+0x58/0xa8 [ 6.855359] really_probe+0xec/0x398 [ 6.855362] driver_probe_device+0x5c/0xb8 [ 6.855367] __device_attach_driver+0x98/0xb8 [ 7.184945] bus_for_each_drv+0x74/0xd8 [ 7.188825] __device_attach+0xec/0x148 [ 7.192705] device_initial_probe+0x24/0x30 [ 7.196937] bus_probe_device+0x9c/0xa8 [ 7.200816] deferred_probe_work_func+0x7c/0xb8 [ 7.205398] process_one_work+0x20c/0x4b0 [ 7.209456] worker_thread+0x48/0x460 [ 7.213157] kthread+0x14c/0x158 [ 7.216432] ret_from_fork+0x10/0x18 [ 7.220049] Code: bad PC value [ 7.223139] ---[ end trace 73f3b21e251d5a70 ]--- Thus this patch removes the __init avoiding crash in such configs. Cc: Andy Gross <agross@kernel.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Saravana Kannan <saravanak@google.com> Cc: Todd Kjos <tkjos@google.com> Cc: Amit Pundir <amit.pundir@linaro.org> Cc: linux-arm-msm@vger.kernel.org Cc: linux-serial@vger.kernel.org Suggested-by: Saravana Kannan <saravanak@google.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20200811025044.70626-1-john.stultz@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: qcom_geni_serial: Fix recent kdb hangDouglas Anderson1-2/+7
The commit e42d6c3ec0c7 ("serial: qcom_geni_serial: Make kgdb work even if UART isn't console") worked pretty well and I've been doing a lot of debugging with it. However, recently I typed "dmesg" in kdb and then held the space key down to scroll through the pagination. My device hung. This was repeatable and I found that it was introduced with the aforementioned commit. It turns out that there are some strange boundary cases in geni where in some weird situations it will signal RX_LAST but then will put 0 in RX_LAST_BYTE. This means that the entire last FIFO entry is valid. This weird corner case is handled in qcom_geni_serial_handle_rx() where you can see that we only honor RX_LAST_BYTE if RX_LAST is set _and_ RX_LAST_BYTE is non-zero. If either of these is not true we use BYTES_PER_FIFO_WORD (4) for the size of the last FIFO word. Let's fix kgdb. While at it, also use the proper #define for 4. Fixes: e42d6c3ec0c7 ("serial: qcom_geni_serial: Make kgdb work even if UART isn't console") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Link: https://lore.kernel.org/r/20200806221904.1.I4455ff86f0ef5281c2a0cd0a4712db614548a5ca@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-07Merge tag 'tty-5.9-rc1' of ↵Linus Torvalds29-184/+444
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial updates from Greg KH: "Here is the large set of TTY and Serial driver patches for 5.9-rc1. Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt and console code. Other highlights include: - much needed vt/vc code cleanup from Jiri Slaby - 8250 driver fixes and additions - various serial driver updates and feature enhancements - locking cleanup for serial/console initializations - other minor cleanups All of these have been in linux-next with no reported issues" * tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (90 commits) MAINTAINERS: enlist Greg formally for console stuff vgacon: Fix for missing check in scrollback handling Revert "serial: 8250: Let serial core initialise spin lock" serial: 8250: Let serial core initialise spin lock tty: keyboard, do not speculate on func_table index serial: stm32: Add RS485 RTS GPIO control serial: 8250_dw: Fix common clocks usage race condition serial: 8250_dw: Pass the same rate to the clk round and set rate methods serial: 8250_dw: Simplify the ref clock rate setting procedure serial: 8250: Add 8250 port clock update method tty: serial: imx: add imx earlycon driver tty: serial: imx: enable imx serial console port as module tty/synclink: remove leftover bits of non-PCI card support tty: Use the preferred form for passing the size of a structure type tty: Fix identation issues in struct serial_struct32 tty: Avoid the use of one-element arrays serial: msm_serial: add sparse context annotation serial: pmac_zilog: add sparse context annotation newport_con: vc_color is now in state serial: imx: use hrtimers for rs485 delays ...
2020-08-06Merge tag 'sched-fifo-2020-08-04' of ↵Linus Torvalds1-2/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull sched/fifo updates from Ingo Molnar: "This adds the sched_set_fifo*() encapsulation APIs to remove static priority level knowledge from non-scheduler code. The three APIs for non-scheduler code to set SCHED_FIFO are: - sched_set_fifo() - sched_set_fifo_low() - sched_set_normal() These are two FIFO priority levels: default (high), and a 'low' priority level, plus sched_set_normal() to set the policy back to non-SCHED_FIFO. Since the changes affect a lot of non-scheduler code, we kept this in a separate tree" * tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits) sched,tracing: Convert to sched_set_fifo() sched: Remove sched_set_*() return value sched: Remove sched_setscheduler*() EXPORTs sched,psi: Convert to sched_set_fifo_low() sched,rcutorture: Convert to sched_set_fifo_low() sched,rcuperf: Convert to sched_set_fifo_low() sched,locktorture: Convert to sched_set_fifo() sched,irq: Convert to sched_set_fifo() sched,watchdog: Convert to sched_set_fifo() sched,serial: Convert to sched_set_fifo() sched,powerclamp: Convert to sched_set_fifo() sched,ion: Convert to sched_set_normal() sched,powercap: Convert to sched_set_fifo*() sched,spi: Convert to sched_set_fifo*() sched,mmc: Convert to sched_set_fifo*() sched,ivtv: Convert to sched_set_fifo*() sched,drm/scheduler: Convert to sched_set_fifo*() sched,msm: Convert to sched_set_fifo*() sched,psci: Convert to sched_set_fifo*() sched,drbd: Convert to sched_set_fifo*() ...
2020-08-05Merge tag 'printk-for-5.9' of ↵Linus Torvalds2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux Pull printk updates from Petr Mladek: - Herbert Xu made printk header file self-contained. - Andy Shevchenko and Sergey Senozhatsky cleaned up console->setup() error handling. - Andy Shevchenko did some cleanups (e.g. sparse warning) in vsprintf code. - Minor documentation updates. * tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: lib/vsprintf: Force type of flags value for gfp_t lib/vsprintf: Replace custom spec to print decimals with generic one lib/vsprintf: Replace hidden BUILD_BUG_ON() with static_assert() printk: Make linux/printk.h self-contained doc:kmsg: explicitly state the return value in case of SEEK_CUR Replace HTTP links with HTTPS ones: vsprintf hvc: unify console setup naming console: Fix trivia typo 'change' -> 'chance' console: Propagate error code from console ->setup() tty: hvc: Return proper error code from console ->setup() hook serial: sunzilog: Return proper error code from console ->setup() hook serial: sunsab: Return proper error code from console ->setup() hook mips: Return proper error code from console ->setup() hook
2020-08-04Merge tag 'arm-drivers-5.9' of ↵Linus Torvalds1-48/+162
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Arnd Bergmann: "A couple of subsystems have their own subsystem maintainers but choose to have the code merged through the soc tree as upstream, as the code tends to be used across multiple SoCs or has SoC specific drivers itself: - memory controllers: Krzysztof Kozlowski takes ownership of the drivers/memory subsystem and its drivers, starting out with a set of cleanup patches. A larger driver for the Tegra memory controller that was accidentally missed for v5.8 is now added. - reset controllers: Only minor updates to drivers/reset this time - firmware: The "turris mox" firmware driver gains support for signed firmware blobs The tegra firmware driver gets extended to export some debug information Various updates to i.MX firmware drivers, mostly cosmetic - ARM SCMI/SCPI: A new mechanism for platform notifications is added, among a number of minor changes. - optee: Probing of the TEE bus is rewritten to better support detection of devices that depend on the tee-supplicant user space. A new firmware based trusted platform module (fTPM) driver is added based on OP-TEE - SoC attributes: A new driver is added to provide a generic soc_device for identifying a machine through the SMCCC ARCH_SOC_ID firmware interface rather than by probing SoC family specific registers. The series also contains some cleanups to the common soc_device code. There are also a number of updates to SoC specific drivers, the main ones are: - Mediatek cmdq driver gains a few in-kernel interfaces - Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding support for additional SoC variants - The Qualcomm GENI core code gains interconnect path voting and performance level support, and integrating this into a number of device drivers. - A new driver for Samsung Exynos5800 voltage coupler for - Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC specific device drivers - Updates to the TI K3 Ring Accelerator driver" * tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits) soc: qcom: geni: Fix unused label warning soc: qcom: smd-rpm: Fix kerneldoc memory: jz4780_nemc: Only request IO memory the driver will use soc: qcom: pdr: Reorder the PD state indication ack MAINTAINERS: Add Git repository for memory controller drivers memory: brcmstb_dpfe: Fix language typo memory: samsung: exynos5422-dmc: Correct white space issues memory: samsung: exynos-srom: Correct alignment memory: pl172: Enclose macro argument usage in parenthesis memory: of: Correct kerneldoc memory: omap-gpmc: Fix language typo memory: omap-gpmc: Correct white space issues memory: omap-gpmc: Use 'unsigned int' for consistency memory: omap-gpmc: Enclose macro argument usage in parenthesis memory: omap-gpmc: Correct kerneldoc memory: mvebu-devbus: Align with open parenthesis memory: mvebu-devbus: Add missing braces to all arms of if statement memory: bt1-l2-ctl: Add blank lines after declarations soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static firmware: ti_sci: Replace HTTP links with HTTPS ones ...
2020-08-02Revert "serial: 8250: Let serial core initialise spin lock"Andy Shevchenko1-0/+1
This reverts commit 679193b7baf8d88e41cbeb397ca17f797654947d. It appears that in QEmu the lock has been initialised differently (it wasn't obvious on real hardware during testing). Let's revert the change until the better approach will be developed. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200802111612.36189-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-31serial: 8250: Let serial core initialise spin lockAndy Shevchenko1-1/+0
Since the serial core handles spin lock initialisation, let the driver rely on it. Depends-on: f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200731123733.22754-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-30serial: stm32: Add RS485 RTS GPIO controlMarek Vasut1-0/+8
While the STM32 does support RS485 drive-enable control within the UART IP itself, some systems have the drive-enable line connected to a pin which cannot be pinmuxed as RTS. Add support for toggling the RTS GPIO line using the modem control GPIOs to provide at least some sort of emulation. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Manivannan Sadhasivam <mani@kernel.org> Cc: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-stm32@st-md-mailman.stormreply.com Link: https://lore.kernel.org/r/20200725144947.537007-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-29serial: 8250_dw: Fix common clocks usage race conditionSerge Semin1-2/+101
The race condition may happen if the UART reference clock is shared with some other device (on Baikal-T1 SoC it's another DW UART port). In this case if that device changes the clock rate while serial console is using it the DW 8250 UART port might not only end up with an invalid uartclk value saved, but may also experience a distorted output data since baud-clock could have been changed. In order to fix this lets at least try to adjust the 8250 port setting like UART clock rate in case if the reference clock rate change is discovered. The driver will call the new method to update 8250 UART port clock rate settings. It's done by means of the clock event notifier registered at the port startup and unregistered in the shutdown callback method. Note 1. In order to avoid deadlocks we had to execute the UART port update method in a dedicated deferred work. This is due to (in my opinion redundant) the clock update implemented in the dw8250_set_termios() method. Note 2. Before the ref clock is manually changed by the custom set_termios() function we swap the port uartclk value with new rate adjusted to be suitable for the requested baud. It is necessary in order to effectively disable a functionality of the ref clock events handler for the current UART port, since uartclk update will be done a bit further in the generic serial8250_do_set_termios() function. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200723003357.26897-5-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-29serial: 8250_dw: Pass the same rate to the clk round and set rate methodsSerge Semin1-3/+3
Indeed according to the clk API if clk_round_rate() has successfully accepted a rate, then in order setup the clock with value returned by the clk_round_rate() the clk_set_rate() method must be called with the original rate value. Suggested-by: Russell King <linux@armlinux.org.uk> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200723003357.26897-4-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-29serial: 8250_dw: Simplify the ref clock rate setting procedureSerge Semin1-11/+4
Really instead of twice checking the clk_round_rate() return value we could do it once, and if it isn't error the clock rate can be changed. By doing so we decrease a number of ret-value tests and remove a weird goto-based construction implemented in the dw8250_set_termios() method. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200723003357.26897-3-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-29serial: 8250: Add 8250 port clock update methodSerge Semin1-0/+40
Some platforms can be designed in a way so the UART port reference clock might be asynchronously changed at some point. In Baikal-T1 SoC this may happen due to the reference clock being shared between two UART ports, on the Allwinner SoC the reference clock is derived from the CPU clock, so any CPU frequency change should get to be known/reflected by/in the UART controller as well. But it's not enough to just update the uart_port->uartclk field of the corresponding UART port, the 8250 controller reference clock divisor should be altered so to preserve current baud rate setting. All of these things is done in a coherent way by calling the serial8250_update_uartclk() method provided in this patch. Though note that it isn't supposed to be called from within the UART port callbacks because the locks using to the protect the UART port data are already taken in there. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200723003357.26897-2-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-29tty: serial: imx: add imx earlycon driverFugang Duan2-0/+58
Split imx earlycon driver from imx serial driver "imx.c" as separated driver. imx serial driver can be built as module, but earlycon driver only support build in. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20200724070815.11445-3-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-29tty: serial: imx: enable imx serial console port as moduleFugang Duan2-40/+6
Add support for building i.MX serial driver as module. The changes of the patch: - imx console driver can be built as module. - move out earlycon code to separated driver like imx_earlycon.c, and imx earlycon driver only support build-in. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20200724070815.11445-2-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-27Merge 5.8-rc7 into tty-nextGreg Kroah-Hartman5-13/+43
we need the tty/serial fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-24serial: exar: Fix GPIO configuration for Sealevel cards based on XR17V35XMatthew Howell1-1/+11
Sealevel XR17V35X based devices are inoperable on kernel versions 4.11 and above due to a change in the GPIO preconfiguration introduced in commit 7dea8165f1d. This patch fixes this by preconfiguring the GPIO on Sealevel cards to the value (0x00) used prior to commit 7dea8165f1d With GPIOs preconfigured as per commit 7dea8165f1d all ports on Sealevel XR17V35X based devices become stuck in high impedance mode, regardless of dip-switch or software configuration. This causes the device to become effectively unusable. This patch (in various forms) has been distributed to our customers and no issues related to it have been reported. Fixes: 7dea8165f1d6 ("serial: exar: Preconfigure xr17v35x MPIOs as output") Signed-off-by: Matthew Howell <matthew.howell@sealevel.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-24serial: msm_serial: add sparse context annotationJohan Hovold1-0/+2
Add sparse context annotation to the receive handlers, which release and reacquire the port lock, to silence sparse warnings: drivers/tty/serial/msm_serial.c:748:25: warning: context imbalance in 'msm_handle_rx_dm' - unexpected unlock drivers/tty/serial/msm_serial.c:814:28: warning: context imbalance in 'msm_handle_rx' - unexpected unlock Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200723123327.5843-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-24serial: pmac_zilog: add sparse context annotationJohan Hovold1-0/+1
Add sparse context annotation to the receive handler, which releases and reacquires the port lock, to silence a sparse warning: drivers/tty/serial/pmac_zilog.c:255:36: sparse: sparse: context imbalance in 'pmz_receive_chars' - unexpected unlock Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200723123327.5843-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-21serial: 8250_mtk: Fix high-speed baud rates clampingSerge Semin1-0/+18
Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") fixed limits of a baud rate setting for a generic 8250 port. In other words since that commit the baud rate has been permitted to be within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely normal for a standard 8250 UART port. But there are custom 8250 ports, which provide extended baud rate limits. In particular the Mediatek 8250 port can work with baud rates up to "uartclk" speed. Normally that and any other peculiarity is supposed to be handled in a custom set_termios() callback implemented in the vendor-specific 8250-port glue-driver. Currently that is how it's done for the most of the vendor-specific 8250 ports, but for some reason for Mediatek a solution has been spread out to both the glue-driver and to the generic 8250-port code. Due to that a bug has been introduced, which permitted the extended baud rate limit for all even for standard 8250-ports. The bug has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") by narrowing the baud rates limit back down to the normal bounds. Unfortunately by doing so we also broke the Mediatek-specific extended bauds feature. A fix of the problem described above is twofold. First since we can't get back the extended baud rate limits feature to the generic set_termios() function and that method supports only a standard baud rates range, the requested baud rate must be locally stored before calling it and then restored back to the new termios structure after the generic set_termios() finished its magic business. By doing so we still use the serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers, while the extended baud rate setting procedure will be performed later in the custom Mediatek-specific set_termios() callback. Second since a true baud rate is now fully calculated in the custom set_termios() method we need to locally update the port timeout by calling the uart_update_timeout() function. After the fixes described above are implemented in the 8250_mtk.c driver, the Mediatek 8250-port should get back to normally working with extended baud rates. Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com Fixes: 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") Reported-by: Daniel Winkler <danielwinkler@google.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: stable <stable@vger.kernel.org> Tested-by: Claire Chang <tientzu@chromium.org> Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2026-05-12 23:14:33 +0300