summaryrefslogtreecommitdiff
path: root/drivers/tty/serial/sh-sci.c
AgeCommit message (Collapse)AuthorFilesLines
2025-06-27serial: sh-sci: Increment the runtime usage counter for the earlycon deviceClaudiu Beznea1-0/+16
commit 651dee03696e1dfde6d9a7e8664bbdcd9a10ea7f upstream. In the sh-sci driver, serial ports are mapped to the sci_ports[] array, with earlycon mapped at index zero. The uart_add_one_port() function eventually calls __device_attach(), which, in turn, calls pm_request_idle(). The identified code path is as follows: uart_add_one_port() -> serial_ctrl_register_port() -> serial_core_register_port() -> serial_core_port_device_add() -> serial_base_port_add() -> device_add() -> bus_probe_device() -> device_initial_probe() -> __device_attach() -> // ... if (dev->p->dead) { // ... } else if (dev->driver) { // ... } else { // ... pm_request_idle(dev); // ... } The earlycon device clocks are enabled by the bootloader. However, the pm_request_idle() call in __device_attach() disables the SCI port clocks while earlycon is still active. The earlycon write function, serial_console_write(), calls sci_poll_put_char() via serial_console_putchar(). If the SCI port clocks are disabled, writing to earlycon may sometimes cause the SR.TDFE bit to remain unset indefinitely, causing the while loop in sci_poll_put_char() to never exit. On single-core SoCs, this can result in the system being blocked during boot when this issue occurs. To resolve this, increment the runtime PM usage counter for the earlycon SCI device before registering the UART port. Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support") Cc: stable@vger.kernel.org Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/20250116182249.3828577-6-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-19serial: sh-sci: Clean sci_ports[0] after at earlycon exitClaudiu Beznea1-2/+30
commit 5f1017069933489add0c08659673443c9905659e upstream. The early_console_setup() function initializes sci_ports[0].port with an object of type struct uart_port obtained from the struct earlycon_device passed as an argument to early_console_setup(). Later, during serial port probing, the serial port used as earlycon (e.g., port A) might be remapped to a different position in the sci_ports[] array, and a different serial port (e.g., port B) might be assigned to slot 0. For example: sci_ports[0] = port B sci_ports[X] = port A In this scenario, the new port mapped at index zero (port B) retains the data associated with the earlycon configuration. Consequently, after the Linux boot process, any access to the serial port now mapped to sci_ports[0] (port B) will block the original earlycon port (port A). To address this, introduce an early_console_exit() function to clean up sci_ports[0] when earlycon is exited. To prevent the cleanup of sci_ports[0] while the serial device is still being used by earlycon, introduce the struct sci_port::probing flag and account for it in early_console_exit(). Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support") Cc: stable@vger.kernel.org Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/20250116182249.3828577-5-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19serial: sh-sci: Move runtime PM enable to sci_probe_single()Claudiu Beznea1-18/+6
commit 239f11209e5f282e16f5241b99256e25dd0614b6 upstream. Relocate the runtime PM enable operation to sci_probe_single(). This change prepares the codebase for upcoming fixes. While at it, replace the existing logic with a direct call to devm_pm_runtime_enable() and remove sci_cleanup_single(). The devm_pm_runtime_enable() function automatically handles disabling runtime PM during driver removal. Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/20250116182249.3828577-3-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19serial: sh-sci: Check if TX data was written to device in .tx_empty()Claudiu Beznea1-0/+29
commit 7cc0e0a43a91052477c2921f924a37d9c3891f0c upstream. On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port() is called. The uart_suspend_port() calls 3 times the struct uart_port::ops::tx_empty() before shutting down the port. According to the documentation, the struct uart_port::ops::tx_empty() API tests whether the transmitter FIFO and shifter for the port is empty. The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the transmit FIFO through the FDR (FIFO Data Count Register). The data units in the FIFOs are written in the shift register and transmitted from there. The TEND bit in the Serial Status Register reports if the data was transmitted from the shift register. In the previous code, in the tx_empty() API implemented by the sh-sci driver, it is considered that the TX is empty if the hardware reports the TEND bit set and the number of data units in the FIFO is zero. According to the HW manual, the TEND bit has the following meaning: 0: Transmission is in the waiting state or in progress. 1: Transmission is completed. It has been noticed that when opening the serial device w/o using it and then switch to a power saving mode, the tx_empty() call in the uart_port_suspend() function fails, leading to the "Unable to drain transmitter" message being printed on the console. This is because the TEND=0 if nothing has been transmitted and the FIFOs are empty. As the TEND=0 has double meaning (waiting state, in progress) we can't determined the scenario described above. Add a software workaround for this. This sets a variable if any data has been sent on the serial console (when using PIO) or if the DMA callback has been called (meaning something has been transmitted). In the tx_empty() API the status of the DMA transaction is also checked and if it is completed or in progress the code falls back in checking the hardware registers instead of relying on the software variable. Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.") Cc: stable@vger.kernel.org Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [claudiu.beznea: fixed conflict by: - keeping serial_port_out() instead of sci_port_out() in sci_transmit_chars() - keeping !uart_circ_empty(xmit) condition in sci_dma_tx_complete(), after s->tx_occurred = true; assignement] Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-04serial: sh-sci: Save and restore more registersGeert Uytterhoeven1-0/+25
commit 81100b9a7b0515132996d62a7a676a77676cb6e3 upstream. On (H)SCIF with a Baud Rate Generator for External Clock (BRG), there are multiple ways to configure the requested serial speed. If firmware uses a different method than Linux, and if any debug info is printed after the Bit Rate Register (SCBRR) is restored, but before termios is reconfigured (which configures the alternative method), the system may lock-up during resume. Fix this by saving and restoring the contents of the BRG Frequency Division (SCDL) and Clock Select (SCCKS) registers as well. Also save and restore the HSCIF's Sampling Rate Register (HSSRR), which configures the sampling point, and the SCIFA/SCIFB's Serial Port Control and Data Registers (SCPCR/SCPDR), which configure the optional control flow signals. After this, all registers that are not saved/restored are either: - read-only, - write-only, - status registers containing flags with clear-after-set semantics, - FIFO Data Count Trigger registers, which do not matter much for the serial console. Fixes: 22a6984c5b5df8ea ("serial: sh-sci: Update the suspend/resume support") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/11c2eab45d48211e75d8b8202cce60400880fe55.1741114989.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04serial: sh-sci: Update the suspend/resume supportClaudiu Beznea1-2/+69
[ Upstream commit 22a6984c5b5df8eab864d7f3e8b94d5a554d31ab ] The Renesas RZ/G3S supports a power saving mode where power to most of the SoC components is turned off. When returning from this power saving mode, SoC components need to be re-configured. The SCIFs on the Renesas RZ/G3S need to be re-configured as well when returning from this power saving mode. The sh-sci code already configures the SCIF clocks, power domain and registers by calling uart_resume_port() in sci_resume(). On suspend path the SCIF UART ports are suspended accordingly (by calling uart_suspend_port() in sci_suspend()). The only missing setting is the reset signal. For this assert/de-assert the reset signal on driver suspend/resume. In case the no_console_suspend is specified by the user, the registers need to be saved on suspend path and restore on resume path. To do this the sci_console_save()/sci_console_restore() functions were added. There is no need to cache/restore the status or FIFO registers. Only the control registers. The registers that will be saved/restored on suspend/resume are specified by the struct sci_suspend_regs data structure. Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20250207113313.545432-1-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-04serial: mctrl_gpio: split disable_ms into sync and no_sync APIsAlexis Lothoré1-1/+1
[ Upstream commit 1bd2aad57da95f7f2d2bb52f7ad15c0f4993a685 ] The following splat has been observed on a SAMA5D27 platform using atmel_serial: BUG: sleeping function called from invalid context at kernel/irq/manage.c:738 in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0 preempt_count: 1, expected: 0 INFO: lockdep is turned off. irq event stamp: 0 hardirqs last enabled at (0): [<00000000>] 0x0 hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec softirqs last disabled at (0): [<00000000>] 0x0 CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74 Hardware name: Atmel SAMA5 Workqueue: hci0 hci_power_on [bluetooth] Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x44/0x70 dump_stack_lvl from __might_resched+0x38c/0x598 __might_resched from disable_irq+0x1c/0x48 disable_irq from mctrl_gpio_disable_ms+0x74/0xc0 mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4 atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8 atmel_set_termios from uart_change_line_settings+0x15c/0x994 uart_change_line_settings from uart_set_termios+0x2b0/0x668 uart_set_termios from tty_set_termios+0x600/0x8ec tty_set_termios from ttyport_set_flow_control+0x188/0x1e0 ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc] wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth] hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth] hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth] hci_power_on [bluetooth] from process_one_work+0x998/0x1a38 process_one_work from worker_thread+0x6e0/0xfb4 worker_thread from kthread+0x3d4/0x484 kthread from ret_from_fork+0x14/0x28 This warning is emitted when trying to toggle, at the highest level, some flow control (with serdev_device_set_flow_control) in a device driver. At the lowest level, the atmel_serial driver is using serial_mctrl_gpio lib to enable/disable the corresponding IRQs accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to disable_irq (called in mctrl_gpio_disable_ms) being possibly called in some atomic context (some tty drivers perform modem lines configuration in regions protected by port lock). Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one and a blocking one. Replace mctrl_gpio_disable_ms calls with the relevant version depending on whether the call is protected by some port lock. Suggested-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Acked-by: Richard Genoud <richard.genoud@bootlin.com> Link: https://lore.kernel.org/r/20250217-atomic_sleep_mctrl_serial_gpio-v3-1-59324b313eef@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-02-17serial: sh-sci: Do not probe the serial port if its slot in sci_ports[] is ↵Claudiu Beznea1-0/+23
in use commit 9f7dea875cc7f9c1a56a5c688290634a59cd1420 upstream. In the sh-sci driver, sci_ports[0] is used by earlycon. If the earlycon is still active when sci_probe() is called and the new serial port is supposed to map to sci_ports[0], return -EBUSY to prevent breaking the earlycon. This situation should occurs in debug scenarios, and users should be aware of the potential conflict. Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support") Cc: stable@vger.kernel.org Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/20250116182249.3828577-4-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-17serial: sh-sci: Drop __initdata macro for port_cfgClaudiu Beznea1-1/+1
commit eaeee4225dba30bef4d424bdf134a07b7f423e8b upstream. The port_cfg object is used by serial_console_write(), which serves as the write function for the earlycon device. Marking port_cfg as __initdata causes it to be freed after kernel initialization, resulting in earlycon becoming unavailable thereafter. Remove the __initdata macro from port_cfg to resolve this issue. Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support") Cc: stable@vger.kernel.org Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Fixes: 0b0cced19ab15c9e ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support") Link: https://lore.kernel.org/r/20250116182249.3828577-2-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-12-09Revert "serial: sh-sci: Clean sci_ports[0] after at earlycon exit"Greg Kroah-Hartman1-28/+0
commit 718632467d88e98816fa01ab12681ef1c2aa56f8 upstream. This reverts commit 3791ea69a4858b81e0277f695ca40f5aae40f312. It was reported to cause boot-time issues, so revert it for now. Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Fixes: 3791ea69a485 ("serial: sh-sci: Clean sci_ports[0] after at earlycon exit") Cc: stable <stable@kernel.org> Cc: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-12-09serial: sh-sci: Clean sci_ports[0] after at earlycon exitClaudiu Beznea1-0/+28
commit 3791ea69a4858b81e0277f695ca40f5aae40f312 upstream. The early_console_setup() function initializes the sci_ports[0].port with an object of type struct uart_port obtained from the object of type struct earlycon_device received as argument by the early_console_setup(). It may happen that later, when the rest of the serial ports are probed, the serial port that was used as earlycon (e.g., port A) to be mapped to a different position in sci_ports[] and the slot 0 to be used by a different serial port (e.g., port B), as follows: sci_ports[0] = port A sci_ports[X] = port B In this case, the new port mapped at index zero will have associated data that was used for earlycon. In case this happens, after Linux boot, any access to the serial port that maps on sci_ports[0] (port A) will block the serial port that was used as earlycon (port B). To fix this, add early_console_exit() that clean the sci_ports[0] at earlycon exit time. Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support") Cc: stable@vger.kernel.org Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/20241106120118.1719888-4-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-06-12serial: sh-sci: protect invalidating RXDMA on shutdownWolfram Sang1-0/+5
[ Upstream commit aae20f6e34cd0cbd67a1d0e5877561c40109a81b ] The to-be-fixed commit removed locking when invalidating the DMA RX descriptors on shutdown. It overlooked that there is still a rx_timer running which may still access the protected data. So, re-add the locking. Reported-by: Dirk Behme <dirk.behme@de.bosch.com> Closes: https://lore.kernel.org/r/ee6c9e16-9f29-450e-81da-4a8dceaa8fc7@de.bosch.com Fixes: 2c4ee23530ff ("serial: sh-sci: Postpone DMA release when falling back to PIO") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/20240506114016.30498-7-wsa+renesas@sang-engineering.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-07-31Merge 6.5-rc4 into tty-nextGreg Kroah-Hartman1-1/+1
We need the serial/tty fixes in here as well for testing and future development. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-25tty: serial: sh-sci: Fix sleeping in atomic contextBiju Das1-1/+1
Fix sleeping in atomic context warning as reported by the Smatch static checker tool by replacing disable_irq->disable_irq_nosync. Reported by: Dan Carpenter <dan.carpenter@linaro.org> Fixes: 8749061be196 ("tty: serial: sh-sci: Add RZ/G2L SCIFA DMA tx support") Cc: stable@kernel.org Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20230704154818.406913-1-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-25tty: Explicitly include correct DT includesRob Herring1-1/+0
The DT of_device.h and of_platform.h date back to the separate of_platform_bus_type before it as merged into the regular platform bus. As part of that merge prepping Arm DT support 13 years ago, they "temporarily" include each other. They also include platform_device.h and of.h. As a result, there's a pretty much random mix of those include files used throughout the tree. In order to detangle these headers and replace the implicit includes with struct declarations, users need to explicitly include the correct includes. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for imx Link: https://lore.kernel.org/r/20230724205440.767071-1-robh@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20tty: serial: sh-sci: Fix end of transmission on SCIBiju Das1-0/+5
We need to set TE to "0" (i.e., disable serial transmission) to get the expected behavior of the end of serial transmission. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230412145053.114847-6-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20tty: serial: sh-sci: Add support for tx end interrupt handlingBiju Das1-3/+28
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section 23.3.7 Serial Data Transmission (Asynchronous Mode), it is mentioned that, set the SCR.TIE bit to 0 and SCR.TEIE bit to 1, after the last data to be transmitted are written to the TDR. This will generate tx end interrupt and in the handler set SCR.TE and SCR.TEIE to 0. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230412145053.114847-5-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20tty: serial: sh-sci: Fix TE setting on SCI IPBiju Das1-2/+17
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section 23.3.7 Serial Data Transmission (Asynchronous Mode) it is mentioned that the TE (transmit enable) must be set after setting TIE (transmit interrupt enable) or these 2 bits are set to 1 simultaneously by a single instruction. So set these 2 bits in single instruction. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230412145053.114847-4-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20tty: serial: sh-sci: Add RZ/G2L SCIFA DMA rx supportBiju Das1-7/+19
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt and DMA transfer request. Setting DMARS register for DMA transfer makes the signal to work as a DMA transfer request signal and subsequent interrupt requests to the interrupt controller are masked. Similarly clearing DMARS register makes signal to work as interrupt signal and subsequent interrupt requests to the interrupt controller are unmasked. Add SCIFA DMA rx support for RZ/G2L alike SoCs by disabling RXI line interrupt and setting DMARS registers by DMA api for DMA transfer request. Apart from this, we must set FIFO trigger to 1 for the expected behavior of the receive transmission. While at it replace the parameter irq to s->irqs[SCIx_RXI_IRQ] in disable_irq_nosync() to match enable_irq() in sci_dma_rx_reenable_irq(). Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230412145053.114847-3-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20tty: serial: sh-sci: Add RZ/G2L SCIFA DMA tx supportBiju Das1-2/+13
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt and DMA transfer request. Setting DMARS register for DMA transfer makes the signal to work as a DMA transfer request signal and subsequent interrupt requests to the interrupt controller are masked. Similarly clearing DMARS register makes signal to work as interrupt signal and subsequent interrupt requests to the interrupt controller are unmasked. Add SCIFA DMA tx support for RZ/G2L alike SoCs by disabling TXI line interrupt and setting DMARS registers by DMA api for DMA transfer request. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230412145053.114847-2-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-10Merge 6.3-rc6 into tty-nextGreg Kroah-Hartman1-1/+9
We need the tty/serial fixes in here for testing. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29tty: serial: sh-sci: Fix Rx on RZ/G2L SCIBiju Das1-1/+1
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI IPs on the SH platform. Currently, it does regshift and configuring Rx wrongly. Drop adding regshift for RZ/G2L alike SoCs. Fixes: dfc80387aefb ("serial: sh-sci: Compute the regshift value for SCI ports") Cc: stable@vger.kernel.org Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29tty: serial: sh-sci: Fix transmit end interrupt handlerBiju Das1-0/+8
The fourth interrupt on SCI port is transmit end interrupt compared to the break interrupt on other port types. So, shuffle the interrupts to fix the transmit end interrupt handler. Fixes: e1d0be616186 ("sh-sci: Add h8300 SCI") Cc: stable <stable@kernel.org> Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230317150403.154094-1-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-29tty: serial: sh-sci: Remove setting {src,dst}_{addr,addr_width} based on DMA ↵Biju Das1-9/+6
direction The direction field in the DMA config is deprecated. The sh-sci driver sets {src,dst}_{addr,addr_width} based on the DMA direction and it results in dmaengine_slave_config() failure as RZ DMAC driver validates {src,dst}_addr_width values independent of DMA direction. Fix this issue by passing both {src,dst}_{addr,addr_width} values independent of DMA direction. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230322074717.6057-1-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-16serial: sh-sci: mark OF related data as maybe unusedKrzysztof Kozlowski1-1/+1
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/tty/serial/sh-sci.c:3144:34: error: ‘of_sci_match’ defined but not used [-Werror=unused-const-variable=] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230310222957.315848-1-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-16serial: Use of_property_present() for testing DT property presenceRob Herring1-1/+1
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. As part of this, convert of_get_property/of_find_property calls to the recently added of_property_present() helper when we just want to test for presence of a property and nothing more. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230310144727.1545630-1-robh@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-12-16Merge tag 'tty-6.2-rc1' of ↵Linus Torvalds1-4/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver updates from Greg KH: "Here is the "big" set of tty/serial driver changes for 6.2-rc1. As in previous kernel releases, nothing big here at all, just some small incremental serial/tty layer cleanups and some individual driver additions and fixes. Highlights are: - serial helper macros from Jiri Slaby to reduce the amount of duplicated code in serial drivers - api cleanups and consolidations from Ilpo Järvinen in lots of serial drivers - the usual set of n_gsm fixes from Daniel Starke as that code gets exercised more - TIOCSTI is finally able to be disabled if requested (security hardening feature from Kees Cook) - fsl_lpuart driver fixes and features added - other small serial driver additions and fixes All of these have been in linux-next for a while with no reported problems" * tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (97 commits) serial: atmel: don't stop the transmitter when doing PIO serial: atmel: cleanup atmel_start+stop_tx() tty: serial: fsl_lpuart: switch to new dmaengine_terminate_* API serial: sunsab: Fix error handling in sunsab_init() serial: altera_uart: fix locking in polling mode serial: pch: Fix PCI device refcount leak in pch_request_dma() tty: serial: fsl_lpuart: Use pm_ptr() to avoid need to make pm __maybe_unused tty: serial: fsl_lpuart: Add runtime pm support tty: serial: fsl_lpuart: enable wakeup source for lpuart serdev: Replace poll loop by readx_poll_timeout() macro tty: synclink_gt: unwind actions in error path of net device open serial: stm32: move dma_request_chan() before clk_prepare_enable() dt-bindings: serial: xlnx,opb-uartlite: Drop 'contains' from 'xlnx,use-parity' serial: pl011: Do not clear RX FIFO & RX interrupt in unthrottle. serial: amba-pl011: avoid SBSA UART accessing DMACR register tty: serial: altera_jtaguart: remove struct altera_jtaguart tty: serial: altera_jtaguart: use uart_port::read_status_mask tty: serial: altera_jtaguart: remove unused altera_jtaguart::sigs tty: serial: altera_jtaguart: remove flag from altera_jtaguart_rx_chars() n_tty: Rename tail to old_tail in n_tty_read() ...
2022-12-02tty: serial: sh-sci: use setup() callback for early consoleJohn Ogness1-4/+16
When setting up the early console, the setup() callback of the regular console is used. It is called manually before registering the early console instead of providing a setup() callback for the early console. This is probably because the early setup needs a different @options during the early stage. The issue here is that the setup() callback is called without the console_list_lock held and functions such as uart_set_options() expect that. Rather than manually calling the setup() function before registering, provide an early console setup() callback that will use the different early options. This ensures that the error checking, ordering, and locking context when setting up the early console are correct. Since this early console can only be registered via the earlyprintk= parameter, the @options argument of the setup() callback will always be NULL. Rather than simply ignoring the argument, add a WARN_ON() to get our attention in case the setup() callback semantics should change in the future. Note that technically the current implementation works because it is only used in early boot. And since the early console setup is performed before registering, it cannot race with anything and thus does not need any locking. However, longterm maintenance is easier when drivers rely on the subsystem API rather than manually implementing steps that could cause breakage in the future. Signed-off-by: John Ogness <john.ogness@linutronix.de> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20221116162152.193147-41-john.ogness@linutronix.de
2022-11-03serial: sh-sci: Use uart_xmit_advance()Ilpo Järvinen1-4/+1
Take advantage of the new uart_xmit_advance() helper. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20221019091151.6692-33-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-30serial: sh-sci: tail is already on valid rangeIlpo Järvinen1-1/+1
There is no need to and tail with UART_XMIT_SIZE - 1 because tail is already on valid range. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220823141839.165244-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-30serial: sh-sci: CIRC_CNT_TO_END() is enoughIlpo Järvinen1-3/+1
Testing also CIRC_CNT() with CIRC_CNT_TO_END() is unnecessary because to latter alone covers all necessary cases. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220823141839.165244-1-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-30serial: Make ->set_termios() old ktermios constIlpo Järvinen1-1/+1
There should be no reason to adjust old ktermios which is going to get discarded anyway. Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-19serial: sh-sci: Don't allow CS5-6Ilpo Järvinen1-1/+5
Only CS7 and CS8 seem supported but CSIZE is not sanitized from CS5 or CS6 to CS8. Set CSIZE correctly so that userspace knows the effective value. Incorrect CSIZE also results in miscalculation of the frame bits in tty_get_char_size() or in its predecessor where the roughly the same code is directly within uart_update_timeout(). Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2) Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220519081808.3776-6-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-03serial: make uart_console_write->putchar()'s character an unsigned charJiri Slaby1-1/+1
Currently, uart_console_write->putchar's second parameter (the character) is of type int. It makes little sense, provided uart_console_write() accepts the input string as "const char *s" and passes its content -- the characters -- to putchar(). So switch the character's type to unsigned char. We don't use char as that is signed on some platforms. That would cause troubles for drivers which (implicitly) cast the char to u16 when writing to the device. Sign extension would happen in that case and the value written would be completely different to the provided char. DZ is an example of such a driver -- on MIPS, it uses u16 for dz_out in dz_console_putchar(). Note we do the char -> uchar conversion implicitly in uart_console_write(). Provided we do not change size of the data type, sign extension does not happen there, so the problem is void. This makes the types consistent and unified with the rest of the uart layer, which uses unsigned char in most places already. One exception is xmit_buf, but that is going to be converted later. Cc: Paul Cercueil <paul@crapouillou.net> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: "Maciej W. Rozycki" <macro@orcam.me.uk> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Karol Gugala <kgugala@antmicro.com> Cc: Mateusz Holenko <mholenko@antmicro.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Manivannan Sadhasivam <mani@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang7@gmail.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <peter@korsgaard.com> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial] Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-21serial: sh-sci: Simplify multiplication/shift logicGeert Uytterhoeven1-1/+1
"a * (1 << b)" == "a << b". No change in generated code. Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/118d62e167f6cf5e98bdf9a738634b4590ea8d09.1645460901.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-20serial: sh-sci: Remove BREAK/FRAME/PARITY/OVERRUN printoutsMagnus Damm1-12/+0
Update the SCIF serial driver to remove printouts for break, frame, parity and overrun errors. This reduces the amount of console printouts generated by the defconfig kernel on R-Car Gen3 for certain use cases. To retrieve more information about such errors the user may inspect counters. Also these errors are fed into the TTY layer for further application specific handling. Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Link: https://lore.kernel.org/r/163884254093.18109.2982470198301927679.sendpatchset@octo Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-17serial: sh-sci: Use devm_clk_get_optional()Geert Uytterhoeven1-8/+7
The sh-sci driver supports up to four input clocks, of which only the first one is mandatory. Replace devm_clk_get() and custom error checking by devm_clk_get_optional(), to simplify the code and to catch all real errors. Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/bce27288cb570952dd96b441e1af8768ad8b4870.1639663832.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-17serial: sh-sci: Use dev_err_probe()Geert Uytterhoeven1-7/+4
Use the dev_err_probe() helper to streamline error handling. Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/5c4dd8df1f8d0d14786f26ee80b77f3eb8e06cd5.1639663832.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-17serial: sh-sci: Drop support for "sci_ick" clockGeert Uytterhoeven1-11/+0
Since commit 1b463bd51042927e ("ARM: dts: r8a7794: Rename the serial port clock to fck") in v4.6, all upstream DTS files call the SCIF functional clock "fck". Hence the time is ripe to drop backward-compatibility with old DTBs that use the old "sci_ick" name. Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/b4103e44d6ac46b6c1c264e2aeac80b39941fe74.1639663832.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-17tty: serial: sh-sci: Add support for R-Car Gen4Yoshihiro Shimoda1-0/+3
Add serial support for R-Car Gen4 SoC. Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20211209070817.1223888-3-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-25serial: sh-sci: Add support to deassert/assert reset lineLad Prabhakar1-7/+32
On RZ/G2L SoC we need to explicitly deassert the reset line for the device to work, use this opportunity to deassert/assert reset line in sh-sci driver. This patch adds support to read the "resets" property (if available) from DT and perform deassert/assert when required. Also, propagate the error to the caller of sci_parse_dt() instead of returning NULL in case of failure. Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Link: https://lore.kernel.org/r/20211110232920.19198-4-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-08-16serial: sh-sci: fix break handling for sysrqUlrich Hecht1-1/+6
This fixes two issues that cause the sysrq sequence to be inadvertently aborted on SCIF serial consoles: - a NUL character remains in the RX queue after a break has been detected, which is then passed on to uart_handle_sysrq_char() - the break interrupt is handled twice on controllers with multiplexed ERI and BRI interrupts Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu> Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-06-15tty: make use of tty_get_{char,frame}_sizeJiri Slaby1-19/+1
In the previous patch, we introduced tty_get_char_size() and tty_get_frame_size() for computing character and frame sizes, respectively. Here, we make use of them in various tty drivers where applicable. The stats look nice: 12 insertions, 169 deletions. Cc: Arnd Bergmann <arnd@arndb.de> Cc: David Lin <dtwlin@gmail.com> Cc: Johan Hovold <johan@kernel.org> Cc: Alex Elder <elder@kernel.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Oliver Neukum <oneukum@suse.com> Acked-by: Alex Elder <elder@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20210610090247.2593-4-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-06-15serial: sh-sci: Stop dmaengine transfer in sci_stop_tx()Yoshihiro Shimoda1-0/+8
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following message is possible output when system enters suspend and while transferring data, because clearing TIE bit in SCSCR is not able to stop any dmaengine transfer. sh-sci e6550000.serial: ttySC1: Unable to drain transmitter Note that this driver has already used some #ifdef in the .c file so that this patch also uses #ifdef to fix the issue. Otherwise, build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled. Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.") Cc: <stable@vger.kernel.org> # v4.9+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20210610110806.277932-1-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-06-09serial: sh-sci: Remove unused STEPFN() macroGeert Uytterhoeven1-3/+0
The last user of the STEPFN() macro was removed in commit d5cb1319a91d4f13 ("serial: sh-sci: Remove manual break debouncing"). Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/970387d104dea5bb7ea674bb89229641467e629b.1623076891.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-06-04serial: sh-sci: Add support for RZ/G2L SoCBiju Das1-1/+11
Add serial support for RZ/G2L SoC with earlycon and extended mode register support. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Link: https://lore.kernel.org/r/20210603221758.10305-11-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13serial: sh-sci: Fix off-by-one error in FIFO threshold register settingGeert Uytterhoeven1-2/+2
The Receive FIFO Data Count Trigger field (RTRG[6:0]) in the Receive FIFO Data Count Trigger Register (HSRTRGR) of HSCIF can only hold values ranging from 0-127. As the FIFO size is equal to 128 on HSCIF, the user can write an out-of-range value, touching reserved bits. Fix this by limiting the trigger value to the FIFO size minus one. Reverse the order of the checks, to avoid rx_trig becoming zero if the FIFO size is one. Note that this change has no impact on other SCIF variants, as their maximum supported trigger value is lower than the FIFO size anyway, and the code below takes care of enforcing these limits. Fixes: a380ed461f66d1b8 ("serial: sh-sci: implement FIFO threshold register setting") Reported-by: Linh Phung <linh.phung.jy@renesas.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/5eff320aef92ffb33d00e57979fd3603bbb4a70f.1620648218.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-15serial: sh-sci: remove obsolete latency workaroundUlrich Hecht1-12/+1
Since the transition to hrtimers there is no more need to set a minimum RX timeout to work around latency issues. Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu> Link: https://lore.kernel.org/r/20210415093547.21639-1-uli+renesas@fpond.eu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-23drivers: tty: serial: sh-sci: fix spelling typo of 'wheter'Wang Qing1-1/+1
wheter -> whether Signed-off-by: Wang Qing <wangqing@vivo.com> Link: https://lore.kernel.org/r/1615345622-2015-1-git-send-email-wangqing@vivo.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-21Revert "serial: sh-sci: Initialize spinlock for uart console"Andy Shevchenko1-3/+0
This reverts commit f38278e9b810b06aff2981d505267be984423ba3. There has been a quick fix against uninitialised lock revealed by the commit f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()"). Since we have now better fix in serial core, this may be safely reverted. Fixes: f38278e9b810 ("serial: sh-sci: Initialize spinlock for uart console") Depends-on: f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200711135346.71171-5-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2026-01-22 00:30:48 +0300