| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit e3b7468f082d106459e86e8dc6fb9bdd65553433 upstream.
Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.
This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 737b0ef3be6b319d6c1fd64193d1603311969326 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.
This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8838b2af23caf1ff0610caef2795d6668a013b2d upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4dd31f1ffec6c370c3c2e0c605628bf5e16d5c46 ]
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty
layer when room available". It was suggested to switch from a while to
a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more
compact.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 01dbb362f0a114fbce19c8abe4cd6f4710e934d5 ]
Warn the upper layer when n_gms is ready to receive data
again. Without this the associated virtual tty remains blocked
indefinitely.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-4-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 84d6f81c1fb58b56eba81ff0a36cf31946064b40 ]
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b2d89ad9c9682e795ed6eeb9ed455789ad6cedf1 upstream.
At least on droid 4 with control channel in ADM mode, there is no response
to Modem Status Command (MSC). Currently gsmtty_modem_update() expects to
have data in dlci->modem_rx unless debug & 2 is set. This means that on
droid 4, things only work if debug & 2 is set.
Let's fix the issue by ignoring empty dlci->modem_rx for ADM mode. In
the AMD mode, CMD_MSC will never respond and gsm_process_modem() won't
get called to set dlci->modem_rx.
And according to ts_127010v140000p.pdf, MSC is only relevant if basic
option is chosen, so let's test for that too.
Fixes: ea3d8465ab9b ("tty: n_gsm: Allow ADM response in addition to UA for control dlci")
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9ec22547986dd32c5c70da78107ce35dbff1344 upstream.
Commit ea3d8465ab9b ("tty: n_gsm: Allow ADM response in addition to UA for
control dlci") added support for DLCI to stay in Asynchronous Disconnected
Mode (ADM). But we still get long delays waiting for commands to other
DLCI to complete:
--> 5) C: SABM(P)
Q> 0) C: UIH(F)
Q> 0) C: UIH(F)
Q> 0) C: UIH(F)
...
This happens because gsm_control_send() sets cretries timer to T2 that is
by default set to 34. This will cause resend for T2 times for the control
frame. In ADM mode, we will never get a response so the control frame, so
retries are just delaying all the commands.
Let's fix the issue by setting DLCI_MODE_ADM flag after detecting the ADM
mode for the control DLCI. Then we can use that in gsm_control_send() to
set retries to 1. This means the control frame will be sent once allowing
the other end at an opportunity to switch from ADM to ABM mode.
Note that retries will be decremented in gsm_control_retransmit() so
we don't want to set it to 0 here.
Fixes: ea3d8465ab9b ("tty: n_gsm: Allow ADM response in addition to UA for control dlci")
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ea3d8465ab9b3e01be329ac5195970a84bef76c5 ]
Some devices have the control dlci stay in ADM mode instead of the UA
mode. This can seen at least on droid 4 when trying to open the ts
27.010 mux port. Enabling n_gsm debug mode shows the control dlci
always respond with DM to SABM instead of UA:
# modprobe n_gsm debug=0xff
# ldattach -d GSM0710 /dev/ttyS0 &
gsmld_output: 00000000: f9 03 3f 01 1c f9
--> 0) C: SABM(P)
gsmld_receive: 00000000: f9 03 1f 01 36 f9
<-- 0) C: DM(P)
...
$ minicom -D /dev/gsmtty1
minicom: cannot open /dev/gsmtty1: No error information
$ strace minicom -D /dev/gsmtty1
...
open("/dev/gsmtty1", O_RDWR|O_NOCTTY|O_NONBLOCK|O_LARGEFILE) = -1 EL2HLT
Note that this is different issue from other n_gsm -EL2HLT issues such
as timeouts when the control dlci does not respond at all.
The ADM mode seems to be a quite common according to "RF Wireless World"
article "GSM Issue-UE sends SABM and gets a DM response instead of
UA response":
This issue is most commonly observed in GSM networks where in UE sends
SABM and expects network to send UA response but it ends up receiving
DM response from the network. SABM stands for Set asynchronous balanced
mode, UA stands for Unnumbered Acknowledge and DA stands for
Disconnected Mode.
An RLP entity can be in one of two modes:
- Asynchronous Balanced Mode (ABM)
- Asynchronous Disconnected Mode (ADM)
Currently Linux kernel closes the control dlci after several retries
in gsm_dlci_t1() on DM. This causes n_gsm /dev/gsmtty ports to produce
error code -EL2HLT when trying to open them as the closing of control
dlci has already set gsm->dead.
Let's fix the issue by allowing control dlci stay in ADM mode after the
retries so the /dev/gsmtty ports can be opened and used. It seems that
it might take several attempts to get any response from the control
dlci, so it's best to allow ADM mode only after the SABM retries are
done.
Note that for droid 4 additional patches are needed to mux the ttyS0
pins and to toggle RTS gpio_149 to wake up the mdm6600 modem are also
needed to use n_gsm. And the mdm6600 modem needs to be powered on.
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
|
|
Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:
struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)
Compile tested only.
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace ASYNC_INITIALIZED bit in the tty_port::flags field with
TTY_PORT_INITIALIZED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_initialized() and tty_port_initialized() to abstract
atomic bit ops.
Note: the transforms for test_and_set_bit() and test_and_clear_bit()
are unnecessary as the state transitions are already mutually exclusive;
the tty lock prevents concurrent open/close/hangup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Dmitry reported, that the current cleanup code in n_gsm can trigger a
warning:
WARNING: CPU: 2 PID: 24238 at drivers/tty/n_gsm.c:2048 gsm_cleanup_mux+0x166/0x6b0()
...
Call Trace:
...
[<ffffffff81247ab9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:490
[<ffffffff828d0456>] gsm_cleanup_mux+0x166/0x6b0 drivers/tty/n_gsm.c:2048
[<ffffffff828d4d87>] gsmld_open+0x5b7/0x7a0 drivers/tty/n_gsm.c:2386
[<ffffffff828b9078>] tty_ldisc_open.isra.2+0x78/0xd0 drivers/tty/tty_ldisc.c:447
[<ffffffff828b973a>] tty_set_ldisc+0x1ca/0xa70 drivers/tty/tty_ldisc.c:567
[< inline >] tiocsetd drivers/tty/tty_io.c:2650
[<ffffffff828a14ea>] tty_ioctl+0xb2a/0x2140 drivers/tty/tty_io.c:2883
...
But this is a legal path when open fails to find a space in the
gsm_mux array and tries to clean up. So make it a standard test
instead of a warning.
Reported-by: "Dmitry Vyukov" <dvyukov@google.com>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/CACT4Y+bHQbAB68VFi7Romcs-Z9ZW3kQRvcq+BvHH1oa5NcAdLA@mail.gmail.com
Fixes: 5a640967 ("tty/n_gsm.c: fix a memory leak in gsmld_open()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Expressions of the form "tty->termios.c_*flag & FLAG"
are more clearly expressed with the termios flags macros,
I_FLAG(), C_FLAG(), O_FLAG(), and L_FLAG().
Convert treewide.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The chars_in_buffer() line discipline method serves no functional
purpose, other than as a (dubious) debugging aid for mostly bit-rotting
drivers. Despite being documented as an optional method, every caller
is unconditionally executed (although conditionally compiled).
Furthermore, direct tty->ldisc access without an ldisc ref is unsafe.
Lastly, N_TTY's chars_in_buffer() has warned of removal since 3.12.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In little endian cases, macro htons unfolds to __swab16 which
provides special case for constants. In big endian cases,
__constant_htons and htons expand directly to the same expression.
So, replace __constant_htons with htons with the goal of getting
rid of the definition of __constant_htons completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_htons(x)
+ htons(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This resolves some tty driver merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
when gsmtty_remove put dlci, it will cause memory leak if dlci->port's refcount is zero.
So we do the cleanup work in .cleanup callback instead.
dlci will be last put in two call chains.
1) gsmld_close -> gsm_cleanup_mux -> gsm_dlci_release -> dlci_put
2) gsmld_remove -> dlci_put
so there is a race. the memory leak depends on the race.
In call chain 2. we hit the memory leak. below comment tells.
release_tty -> tty_driver_remove_tty -> gsmtty_remove -> dlci_put -> tty_port_destructor (WARN_ON(port->itty) and return directly)
|
tty->port->itty = NULL;
|
tty_kref_put ---> release_one_tty -> gsmtty_cleanup (added by our patch)
So our patch fix the memory leak by doing the cleanup work after tty core did.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Fixes: dfabf7ffa30585
Cc: stable <stable@vger.kernel.org> # 3.14+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty_name no longer uses the buf parameter, so remove it along with all
the 64 byte stack buffers that used to be passed in.
Mostly generated by the coccinelle script
@depends on patch@
identifier buf;
constant C;
expression tty;
@@
- char buf[C];
<+...
- tty_name(tty, buf)
+ tty_name(tty)
...+>
allmodconfig compiles, so I'm fairly confident the stack buffers
weren't used for other purposes as well.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The result of netdev_priv is already implicitly cast to the type of the
left side of the assignment.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
T *x;
@@
x =
- (T *)
netdev_priv(...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
this patch fixes following sparse warning:
n_gsm.c:2827:22: warning: symbol 'tty_ldisc_packet' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
|
|
If gsmld_attach_gsm fails, the gsm is not used anymore.
tty core will not call gsmld_close to do the cleanup work.
tty core just restore to the tty old ldisc.
That always causes memory leak.
Signed-off-by: xinhui.pan <xinhuiX.pan@intel.com>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Just a simple cleanup of init_timer with setting the fields manually.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
gsm->num is the index of gsm_mux[], it's invalid before calling gsm_activate_mux.
Signed-off-by: xinhui.pan <xinhuiX.pan@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Extend alloc_netdev{,_mq{,s}}() to take name_assign_type as argument, and convert
all users to pass NET_NAME_UNKNOWN.
Coccinelle patch:
@@
expression sizeof_priv, name, setup, txqs, rxqs, count;
@@
(
-alloc_netdev_mqs(sizeof_priv, name, setup, txqs, rxqs)
+alloc_netdev_mqs(sizeof_priv, name, NET_NAME_UNKNOWN, setup, txqs, rxqs)
|
-alloc_netdev_mq(sizeof_priv, name, setup, count)
+alloc_netdev_mq(sizeof_priv, name, NET_NAME_UNKNOWN, setup, count)
|
-alloc_netdev(sizeof_priv, name, setup)
+alloc_netdev(sizeof_priv, name, NET_NAME_UNKNOWN, setup)
)
v9: move comments here from the wrong commit
Signed-off-by: Tom Gundersen <teg@jklm.no>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
3GPP TS 07.10 states in section 5.4.6.3.7:
"The length byte contains the value 2 or 3 ... depending on the break
signal." The break byte is optional and if it is sent, the length is
3. In fact the driver was not able to work with modems that send this
break byte in their modem status control message. If the modem just
sends the break byte if it is really set, then weird things might
happen.
The code for deconding the modem status to the internal linux
presentation in gsm_process_modem has already a big comment about
this 2 or 3 byte length thing and it is already able to decode the
brk, but the code calling the gsm_process_modem function in
gsm_control_modem does not encode it and hand it over the right way.
This patch fixes this.
Without this fix if the modem sends the brk byte in it's modem status
control message the driver will hang when opening a muxed channel.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 4d9b109060f690f5c835(tty: Prevent deadlock in n_gsm driver)
tried to close all the virtual ports synchronously before closing the
phycial ports, so the tty_vhangup() is used.
But the tty_unlock/lock() is wrong:
tty_release
tty_ldisc_release
tty_lock_pair(tty, o_tty) < == Here the tty is for physical port
tty_ldisc_kill
gsmld_close
gsm_cleanup_mux
gsm_dlci_release
tty = tty_port_tty_get(&dlci->port)
< == Here the tty(s) are for virtual port
They are different ttys, so before tty_vhangup(virtual tty), do not need
to call the tty_unlock(virtual tty) at all which causes unbalanced unlock
warning.
When enabling mutex debugging option, we will hit the below warning also:
[ 99.276903] =====================================
[ 99.282172] [ BUG: bad unlock balance detected! ]
[ 99.287442] 3.10.20-261976-gaec5ba0 #44 Tainted: G O
[ 99.293972] -------------------------------------
[ 99.299240] mmgr/152 is trying to release lock (&tty->legacy_mutex) at:
[ 99.306693] [<c1b2dcad>] mutex_unlock+0xd/0x10
[ 99.311669] but there are no more locks to release!
[ 99.317131]
[ 99.317131] other info that might help us debug this:
[ 99.324440] 3 locks held by mmgr/152:
[ 99.328542] #0: (&tty->legacy_mutex/1){......}, at: [<c1b30ab0>] tty_lock_nested+0x40/0x90
[ 99.338116] #1: (&tty->ldisc_mutex){......}, at: [<c15dbd02>] tty_ldisc_kill+0x22/0xd0
[ 99.347284] #2: (&gsm->mutex){......}, at: [<c15e3d83>] gsm_cleanup_mux+0x73/0x170
[ 99.356060]
[ 99.356060] stack backtrace:
[ 99.360932] CPU: 0 PID: 152 Comm: mmgr Tainted: G O 3.10.20-261976-gaec5ba0 #44
[ 99.370086] ef4a4de0 ef4a4de0 ef4c1d98 c1b27b91 ef4c1db8 c1292655 c1dd10f5 c1b2dcad
[ 99.378921] c1b2dcad ef4a4de0 ef4a528c ffffffff ef4c1dfc c12930dd 00000246 00000000
[ 99.387754] 00000000 00000000 c15e1926 00000000 00000001 ddfa7530 00000003 c1b2dcad
[ 99.396588] Call Trace:
[ 99.399326] [<c1b27b91>] dump_stack+0x16/0x18
[ 99.404307] [<c1292655>] print_unlock_imbalance_bug+0xe5/0xf0
[ 99.410840] [<c1b2dcad>] ? mutex_unlock+0xd/0x10
[ 99.416110] [<c1b2dcad>] ? mutex_unlock+0xd/0x10
[ 99.421382] [<c12930dd>] lock_release_non_nested+0x1cd/0x210
[ 99.427818] [<c15e1926>] ? gsm_destroy_network+0x36/0x130
[ 99.433964] [<c1b2dcad>] ? mutex_unlock+0xd/0x10
[ 99.439235] [<c12931a2>] lock_release+0x82/0x1c0
[ 99.444505] [<c1b2dcad>] ? mutex_unlock+0xd/0x10
[ 99.449776] [<c1b2dcad>] ? mutex_unlock+0xd/0x10
[ 99.455047] [<c1b2dc2f>] __mutex_unlock_slowpath+0x5f/0xd0
[ 99.461288] [<c1b2dcad>] mutex_unlock+0xd/0x10
[ 99.466365] [<c1b30bb1>] tty_unlock+0x21/0x50
[ 99.471345] [<c15e3dd1>] gsm_cleanup_mux+0xc1/0x170
[ 99.476906] [<c15e44d2>] gsmld_close+0x52/0x90
[ 99.481983] [<c15db905>] tty_ldisc_close.isra.1+0x35/0x50
[ 99.488127] [<c15dbd0c>] tty_ldisc_kill+0x2c/0xd0
[ 99.493494] [<c15dc7af>] tty_ldisc_release+0x2f/0x50
[ 99.499152] [<c15d572c>] tty_release+0x37c/0x4b0
[ 99.504424] [<c1b2dcad>] ? mutex_unlock+0xd/0x10
[ 99.509695] [<c1b2dcad>] ? mutex_unlock+0xd/0x10
[ 99.514967] [<c1372f6e>] ? eventpoll_release_file+0x7e/0x90
[ 99.521307] [<c1335849>] __fput+0xd9/0x200
[ 99.525996] [<c133597d>] ____fput+0xd/0x10
[ 99.530685] [<c125c731>] task_work_run+0x81/0xb0
[ 99.535957] [<c12019e9>] do_notify_resume+0x49/0x70
[ 99.541520] [<c1b30dc4>] work_notifysig+0x29/0x31
[ 99.546897] ------------[ cut here ]------------
So here we can call tty_vhangup() directly which is for virtual port.
Reviewed-by: Chao Bi <chao.bi@intel.com>
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Marks the functions gsm_cleanup_mux(), gsm_activate_mux(),
gsm_free_mux(), gsm_alloc_mux() and gsm_change_mtu() as static in
n_gsm.c because they are not used outside this file.
Also, drop the EXPORT_SYMBOL_GPL for the above mentioned functions
because nothing else in the kernel calls them.
This eliminates the following warnings in n_gsm.c:
drivers/tty/n_gsm.c:2022:6: warning: no previous prototype for ‘gsm_cleanup_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2076:5: warning: no previous prototype for ‘gsm_activate_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2120:6: warning: no previous prototype for ‘gsm_free_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2156:17: warning: no previous prototype for ‘gsm_alloc_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2714:5: warning: no previous prototype for ‘gsm_change_mtu’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ttyA has ld associated to n_gsm, when ttyA is closing, it triggers
to release gsmttyB's ld data dlci[B], then race would happen if gsmttyB
is opening in parallel.
(Note: This patch set differs from previous set in that it uses mutex
instead of spin lock to avoid race, so that it avoids sleeping in automic
context)
Here are race cases we found recently in test:
CASE #1
====================================================================
releasing dlci[B] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(gsmttyB), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[B]) -----
| |
gsm_dlci_free(dlci[B]) -----
| |
----- gsmtty_open(gsmttyB)
gsmtty_open()
{
struct gsm_dlci *dlci = tty->driver_data; => here it uses dlci[B]
...
}
In gsmtty_open(gsmttyA), it uses dlci[B] which was release, so hit a panic.
=====================================================================
CASE #2
=====================================================================
releasing dlci[0] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
| |
----- gsmtty_open(gsmttyB) fail
| |
----- tty_release(gsmttyB)
| |
----- gsmtty_close(gsmttyB)
| |
----- gsmtty_detach_dlci(dlci[B])
| |
----- dlci_put(dlci[B])
| |
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[0]) -----
| |
gsm_dlci_free(dlci[0]) -----
| |
----- dlci_put(dlci[0])
In gsmtty_detach_dlci(dlci[B]), it tries to use dlci[0] which was released,
then hit panic.
=====================================================================
IMHO, n_gsm tty operations would refer released ldisc, as long as
gsm_dlci_release() has chance to release ldisc data when some gsmtty operations
are ongoing..
This patch is try to avoid it by:
1) in n_gsm driver, use a global gsm mutex lock to avoid gsm_dlci_release() run in
parallel with gsmtty_install();
2) Increase dlci's ref count in gsmtty_install() instead of in gsmtty_open(), the
purpose is to prevent gsm_dlci_release() releasing dlci after gsmtty_install()
allocats dlci but before gsmtty_open increases dlci's ref count;
3) Decrease dlci's ref count in gsmtty_remove(), a tty framework API, this is the
opposite process of step 2).
Signed-off-by: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most line disciplines already handle the undocumented NULL flag
ptr in their .receive_buf method; however, several don't.
Document the NULL flag ptr, and correct handling in the
N_MOUSE, N_GSM0710 and N_R394 line disciplines.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Specifically:
n_gsm.c:810: ERROR: space required before the open parenthesis '('
n_gsm.c:830: WARNING: line over 80 characters
n_gsm.c:971: ERROR: trailing whitespace
n_gsm.c:984: ERROR: code indent should use tabs where possible
n_gsm.c:984: WARNING: please, no space before tabs
n_gsm.c:984: WARNING: please, no spaces at the start of a line
n_gsm.c:1141: WARNING: space prohibited before semicolon
n_gsm.c:1743: ERROR: space required before the open brace '{'
n_gsm.c:1744: WARNING: line over 80 characters
n_gsm.c:1745: ERROR: code indent should use tabs where possible
n_gsm.c:1746: ERROR: code indent should use tabs where possible
n_gsm.c:2908: WARNING: line over 80 characters
n_gsm.c:2912: ERROR: trailing whitespace
Signed-off-by: Aldo Iljazi <neonsync1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move HUPCL handling to port shutdown so that DTR is dropped also on hang
up (tty_port_close is a noop for hung-up ports).
Also do not try to drop DTR for uninitialised ports where it has never
been raised (e.g. after a failed open).
Note that this is also the current behaviour of serial-core.
Nine drivers currently call tty_port_close_start directly (rather than
through tty_port_close) and seven of them lower DTR as part of their
close (if the port has been initialised). Fixup the remaining two
drivers so that it continues to be lowered also on normal (non-HUP)
close. [ Note that most of those other seven drivers did not expect DTR
to have been dropped by tty_port_close_start in the first place. ]
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change fixes a deadlock when the multiplexer is closed while there
are still client side ports open.
When the multiplexer is closed and there are active tty's it tries to
close them with tty_vhangup. This has a problem though, because
tty_vhangup needs the tty_lock. This patch changes it to unlock the
tty_lock before attempting the hangup and relocks afterwards. The
additional call to tty_port_tty_set is needed because otherwise the
port stays active because of the reference counter.
This change also exposed another problem that other code paths don't
expect that the multiplexer could have been closed. This patch also adds
checks for these cases in the gsmtty_ class of function that could be
called.
The documentation explicitly states that "first close all virtual ports
before closing the physical port" but we've found this to not always
reality in our field situations. The GPRS / UTMS modem sometimes crashes
and needs a power cycle in that case which means cleanly shutting down
everything is not always possible. This change makes it much more robust
for our situation where at least the system is recoverable with this patch
and doesn't hang in a deadlock situation inside the kernel.
The patch is against the long term support kernel (3.4.27) and should
apply cleanly to more recent branches. Tested with a Telit GE864-QUADV2
and Telit HE910 modem.
Signed-off-by: Dirkjan Bussink <dirkjan.bussink@nedap.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit f96f7f7f39af53274d98aa9c29d6fa4d122218a4, at the
request of Jin.
Cc: xiaojin <jin.xiao@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All the call to gsm->output should be in the tx_lock,
that could avoid potential race from MUX level. But
we have no tx_lock in gsm_send.
This patch is to add tx_lock in gsm_send.
Signed-off-by: xiaojin <jin.xiao@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
Here it is enough to switch to refcounting in tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the trace we print the wrong values for N(R) on an I frame.
Correct the mask.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Uplink (TX) network data will go through gsm_dlci_data_output_framed
there is a bug where if memory allocation fails, the skb which
has already been pulled off the list will be lost.
In addition TX skbs were being processed in LIFO order
Fixed the memory leak, and changed to FIFO order processing
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Showjumping <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drivers are supposed to use the dev_* versions of the kfree_skb
interfaces. In a couple of cases we were called with IRQs
disabled as well which kfree_skb() does not expect.
Replaced kfree_skb calls w/ dev_kfree_skb and dev_kfree_skb_any
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Grooming <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
gsm_data_kick was recently modified to allow messages on the
tx queue bound for DLCI0 to flow even during FCOFF conditions.
Unfortunately we introduced a bug discovered by code inspection
where subsequent list traversers can access freed memory if
the DLCI0 messages were not all at the head of the list.
Replaced singly linked tx list w/ a list_head and used
provided interfaces for traversing and deleting members.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There were some locking holes in the management of the MUX's
message queue for 2 code paths:
1) gsmld_write_wakeup
2) receipt of CMD_FCON flow-control message
In both cases gsm_data_kick is called w/o locking so it can collide
with other other instances of gsm_data_kick (pulling messages tx_tail)
or potentially other instances of __gsm_data_queu (adding messages to tx_head)
Changed to take the tx_lock in these 2 cases
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The design of uplink flow control in the mux driver is
that for constipated channels data will backup into the
per-channel fifos, and any messages that make it to the
outbound message queue will still go out.
Code was added to also stop messages that were in the outbound
queue but this requires filtering through all the messages on the
queue for stopped dlcis and changes some of the mux logic unneccessarily.
The message fiiltering was removed to be in line w/ the original design
as the message filtering does not provide any solution.
Extra debug messages used during investigation were also removed.
Signed-off-by: samix.lebsir <samix.lebsir@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Dressage <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
- Correcting handling of FCon/FCoff in order to respect 27.010 spec
- Consider FCon/off will overide all dlci flow control except for
dlci0 as we must be able to send control frames.
- Dlci constipated handling according to FC, RTC and RTR values.
- Modifying gsm_dlci_data_kick and gsm_dlci_data_sweep according
to dlci constipated value
Signed-off-by: Frederic Berat <fredericx.berat@intel.com>
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
gsm_dlci_data_kick will not call any output function if tx_bytes > THRESH_LO
furthermore it will call the output function only once if tx_bytes == 0
If the size of the IP writes are on the order of THRESH_LO
we can get into a situation where skbs accumulate on the outbound list
being starved for events to call the output function.
gsm_dlci_data_kick now calls the sweep function when tx_bytes==0
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Hay and Water <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
