| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Passing a struct thermal_trip pointer instead of a trip index to the
.get_trend() thermal zone callback allows one of its 2 implementations,
the thermal_get_trend() function in the ACPI thermal driver, to be
simplified quite a bit, and the other implementation of it in the
ti-soc-thermal driver does not even use the relevant callback argument.
For this reason, change the .get_trend() thermal zone callback
definition and adjust the related code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After recent changes in the ACPI thermal driver and in the Intel DTS
IOSF thermal driver, all thermal zone drivers are expected to use trip
tables for initialization and none of them should implement
.get_trip_type(), .get_trip_temp() or .get_trip_hyst() callbacks, so
drop these callbacks entirely from the core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Merge ARM and related thermal control updates for 6.6-rc1 from Daniel
Lezcano:
"- Check if the Tegra BPMP supports the trip points in order to set the
.set_trips callback (Mikko Perttunen)
- Add the new Loongson-2 thermal sensor along with the DT bindings
(Yinbo Zhu)
- Use IS_ERR_OR_NULL helper to replace a double test on the TI bandgap
sensor (Li Zetao)
- Remove the call to platform_set_drvdata() as there is no call to
platform_get_drvdata() in a bunch of drivers where that happens
(Andrei Coardos)
- Switch the Mediatek LVTS mode to filtered in order to enable the
interrupts (Nícolas F. R. A. Prado)
- Fix Wvoid-pointer-to-enum-cast warning on the Exynos TMU (Krzysztof
Kozlowski)
- Remove redundant usage of of_match_ptr() as the driver db8500
already depends on CONFIG_OF (Ruan Jinjie)
- Remove redundant dev_err_probe() because the underlying function
already called it in the Mediatek sensor (Chen Jiahao)
- Free calibration nvmem after reading it on sun8i (Mark Brown)
- Remove useless comment in the code on sun8i (Yangtao Li)
- Make tsens_xxxx_nvmem static to fix sparse warning on QCom tsens (Min-Hua Chen)
- Remove error message at probe deferral on imx8mm (Ahmad Fatoum)
- Fix parameter check in lvts_debugfs_init with IS_ERR on Mediatek
LVTS (Minjie Du)
- Fix the interrupt routine and configuratoin for the Mediatek LVTS
(Nícolas F. R. A. Prado)"
* tag 'thermal-v6.6-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (27 commits)
thermal/drivers/tegra-bpmp: Check if BPMP supports trip points
thermal: dt-bindings: add loongson-2 thermal
thermal/drivers/loongson-2: Add thermal management support
thermal/drivers/ti-soc-thermal: Use helper function IS_ERR_OR_NULL()
thermal/drivers/generic-adc: Removed unneeded call to platform_set_drvdata()
thermal/drivers/max77620_thermal: Removed unneeded call to platform_set_drvdata()
thermal/drivers/mediatek/auxadc_thermal: Removed call to platform_set_drvdata()
thermal/drivers/sun8i_thermal: Remove unneeded call to platform_set_drvdata()
thermal/drivers/broadcom/brcstb_thermal: Removed unneeded platform_set_drvdata()
thermal/drivers/mediatek/lvts_thermal: Make readings valid in filtered mode
thermal/drivers/k3_bandgap: Remove unneeded call to platform_set_drvdata()
thermal/drivers/k3_j72xx_bandgap: Removed unneeded call to platform_set_drvdata()
thermal/drivers/broadcom/sr-thermal: Removed call to platform_set_drvdata()
thermal/drivers/samsung: Fix Wvoid-pointer-to-enum-cast warning
thermal/drivers/db8500: Remove redundant of_match_ptr()
thermal/drivers/mediatek: Clean up redundant dev_err_probe()
thermal/drivers/sun8i: Free calibration nvmem after reading it
thermal/drivers/sun8i: Remove unneeded comments
thermal/drivers/tsens: Make tsens_xxxx_nvmem static
thermal/drivers/imx8mm: Suppress log message on probe deferral
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These rework the Intel DTS IOSF and the ACPI thermal drivers to pass
tables of generic trip point structures to the core during
initialization and make some requisite modifications in the thermal
core, fix a few issues elsewhere and clean up code.
This includes changes that are present in the ACPI updates too,
because they involve both ACPI and the thermal core. The list of
specific changes below is limited to thermal control, however.
Specifics:
- Make the ACPI thermal driver use its own Notify() handler (Michal
Wilczynski)
- Rework the ACPI thermal driver to use a table of generic trip point
structures on top of the internal representation of trip points and
remove thermal zone callbacks that are not necessary any more from
that driver (Rafael Wysocki)
- Fix a few issues in the Intel DTS IOSF thermal driver, clean up
code in it and make it pass tables of generic trip point structures
to the core during thermal zone registration (Rafael Wysocki)
- Drop a redundant check from the Intel DTS IOSF thermal driver's
"remove" routine (Zhang Rui)
- Use module_platform_driver() to replace an open-coded counterpart
of it in the int340x thermal driver (Yang Yingliang)
- Fix possible uninitialized value access in __thermal_of_bind() and
__thermal_of_unbind() (Peng Fan)
- Make the int3400 driver use thermal zone device wrappers (Daniel
Lezcano)
- Remove redundant thermal zone state check from the int340x thermal
driver (Daniel Lezcano)
- Drop non-functional nocrt parameter from ACPI thermal (Mario
Limonciello)
- Explicitly include correct DT includes in the thermal core and
drivers (Rob Herring)"
* tag 'thermal-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: intel_soc_dts_iosf: Remove redundant check
thermal: intel: int340x: simplify the code with module_platform_driver()
thermal/of: Fix potential uninitialized value access
thermal: intel: intel_soc_dts_iosf: Use struct thermal_trip
thermal: intel: intel_soc_dts_iosf: Rework critical trip setup
thermal: intel: intel_soc_dts_iosf: Add helper for resetting trip points
thermal: intel: intel_soc_dts_iosf: Change initialization ordering
thermal: intel: intel_soc_dts_iosf: Pass sensors to update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Untangle update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Always assume notification support
thermal: intel: intel_soc_dts_iosf: Drop redundant symbol definition
thermal: intel: intel_soc_dts_iosf: Always use 2 trips
thermal: Explicitly include correct DT includes
thermal/drivers/int340x: Do not check the thermal zone state
thermal/drivers/int3400: Use thermal zone device wrappers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include new ACPICA material, a rework of the ACPI thermal
driver, a switch-over of the ACPI processor driver to using _OSC
instead of (long deprecated) _PDC for CPU initialization, a rework of
firmware notifications handling in several drivers, fixes and cleanups
for suspend-to-idle handling on AMD systems, ACPI backlight driver
updates and more.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20230628
including the following changes:
- Suppress a GCC 12 dangling-pointer warning (Philip Prindeville)
- Reformat the ACPI_STATE_COMMON macro and its users (George Guo)
- Replace the ternary operator with ACPI_MIN() (Jiangshan Yi)
- Add support for _DSC as per ACPI 6.5 (Saket Dumbre)
- Remove a duplicate macro from zephyr header (Najumon B.A)
- Add data structures for GED and _EVT tracking (Jose Marinho)
- Fix misspelled CDAT DSMAS define (Dave Jiang)
- Simplify an error message in acpi_ds_result_push() (Christophe
Jaillet)
- Add a struct size macro related to SRAT (Dave Jiang)
- Add AML_NO_OPERAND_RESOLVE flag to Timer (Abhishek Mainkar)
- Add support for RISC-V external interrupt controllers in MADT
(Sunil V L)
- Add RHCT flags, CMO and MMU nodes (Sunil V L)
- Change ACPICA version to 20230628 (Bob Moore)
- Introduce new wrappers for ACPICA notify handler install/remove and
convert multiple drivers to using their own Notify() handlers
instead of the ACPI bus type .notify() slated for removal (Michal
Wilczynski)
- Add backlight=native DMI quirk for Apple iMac12,1 and iMac12,2
(Hans de Goede)
- Put ACPI video and its child devices explicitly into D0 on boot to
avoid platform firmware confusion (Kai-Heng Feng)
- Add backlight=native DMI quirk for Lenovo Ideapad Z470 (Jiri Slaby)
- Support obtaining physical CPU ID from MADT on LoongArch (Bibo Mao)
- Convert ACPI CPU initialization to using _OSC instead of _PDC that
has been depreceted since 2018 and dropped from the specification
in ACPI 6.5 (Michal Wilczynski, Rafael Wysocki)
- Drop non-functional nocrt parameter from ACPI thermal (Mario
Limonciello)
- Clean up the ACPI thermal driver, rework the handling of firmware
notifications in it and make it provide a table of generic trip
point structures to the core during initialization (Rafael Wysocki)
- Defer enumeration of devices with _DEP pointing to IVSC (Wentong
Wu)
- Install SystemCMOS address space handler for ACPI000E (TAD) to meet
platform firmware expectations on some platforms (Zhang Rui)
- Fix finding the generic error data in the ACPi extlog driver for
compatibility with old and new firmware interface versions
(Xiaochun Lee)
- Remove assorted unused declarations of functions (Yue Haibing)
- Move AMBA bus scan handling into arm64 specific directory (Sudeep
Holla)
- Fix and clean up suspend-to-idle interface for AMD systems (Mario
Limonciello, Andy Shevchenko)
- Fix string truncation warning in pnpacpi_add_device() (Sunil V L)"
* tag 'acpi-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (66 commits)
ACPI: x86: s2idle: Add a function to get LPS0 constraint for a device
ACPI: x86: s2idle: Add for_each_lpi_constraint() helper
ACPI: x86: s2idle: Add more debugging for AMD constraints parsing
ACPI: x86: s2idle: Fix a logic error parsing AMD constraints table
ACPI: x86: s2idle: Catch multiple ACPI_TYPE_PACKAGE objects
ACPI: x86: s2idle: Post-increment variables when getting constraints
ACPI: Adjust #ifdef for *_lps0_dev use
ACPI: TAD: Install SystemCMOS address space handler for ACPI000E
ACPI: Remove assorted unused declarations of functions
ACPI: extlog: Fix finding the generic error data for v3 structure
PNP: ACPI: Fix string truncation warning
ACPI: Remove unused extern declaration acpi_paddr_to_node()
ACPI: video: Add backlight=native DMI quirk for Apple iMac12,1 and iMac12,2
ACPI: video: Put ACPI video and its child devices into D0 on boot
ACPI: processor: LoongArch: Get physical ID from MADT
ACPI: scan: Defer enumeration of devices with a _DEP pointing to IVSC device
ACPI: thermal: Eliminate code duplication from acpi_thermal_notify()
ACPI: thermal: Drop unnecessary thermal zone callbacks
ACPI: thermal: Rework thermal_get_trend()
ACPI: thermal: Use trip point table to register thermal zones
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf event updates from Ingo Molnar:
- AMD IBS improvements
- Intel PMU driver updates
- Extend core perf facilities & the ARM PMU driver to better handle ARM big.LITTLE events
- Micro-optimize software events and the ring-buffer code
- Misc cleanups & fixes
* tag 'perf-core-2023-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore: Remove unnecessary ?: operator around pcibios_err_to_errno() call
perf/x86/intel: Add Crestmont PMU
x86/cpu: Update Hybrids
x86/cpu: Fix Crestmont uarch
x86/cpu: Fix Gracemont uarch
perf: Remove unused extern declaration arch_perf_get_page_size()
perf: Remove unused PERF_PMU_CAP_HETEROGENEOUS_CPUS capability
arm_pmu: Remove unused PERF_PMU_CAP_HETEROGENEOUS_CPUS capability
perf/x86: Remove unused PERF_PMU_CAP_HETEROGENEOUS_CPUS capability
arm_pmu: Add PERF_PMU_CAP_EXTENDED_HW_TYPE capability
perf/x86/ibs: Set mem_lvl_num, mem_remote and mem_hops for data_src
perf/mem: Add PERF_MEM_LVLNUM_NA to PERF_MEM_NA
perf/mem: Introduce PERF_MEM_LVLNUM_UNC
perf/ring_buffer: Use local_try_cmpxchg in __perf_output_begin
locking/arch: Avoid variable shadowing in local_try_cmpxchg()
perf/core: Use local64_try_cmpxchg in perf_swevent_set_period
perf/x86: Use local64_try_cmpxchg
perf/amd: Prevent grouping of IBS events
|
|
Merge ACPI thermal driver changes for 6.6-rc1:
- Drop non-functional nocrt parameter from ACPI thermal (Mario
Limonciello).
- Clean up the ACPI thermal driver, rework the handling of firmware
notifications in it and make it provide a table of generic trip point
structures to the core during initialization (Rafael Wysocki).
* acpi-thermal:
ACPI: thermal: Eliminate code duplication from acpi_thermal_notify()
ACPI: thermal: Drop unnecessary thermal zone callbacks
ACPI: thermal: Rework thermal_get_trend()
ACPI: thermal: Use trip point table to register thermal zones
thermal: core: Rework and rename __for_each_thermal_trip()
ACPI: thermal: Introduce struct acpi_thermal_trip
ACPI: thermal: Carry out trip point updates under zone lock
ACPI: thermal: Clean up acpi_thermal_register_thermal_zone()
thermal: core: Add priv pointer to struct thermal_trip
thermal: core: Introduce thermal_zone_device_exec()
thermal: core: Do not handle trip points with invalid temperature
ACPI: thermal: Drop redundant local variable from acpi_thermal_resume()
ACPI: thermal: Do not attach private data to ACPI handles
ACPI: thermal: Drop enabled flag from struct acpi_thermal_active
ACPI: thermal: Drop nocrt parameter
|
|
These remove a redundant check from a driver's "remove" routine
and use module_platform_driver() to replace an open-coded version
of it in one driver.
* thermal-intel:
thermal: intel: intel_soc_dts_iosf: Remove redundant check
thermal: intel: int340x: simplify the code with module_platform_driver()
|
|
Remove the redundant check in remove_dts_thermal_zone() because all of
its existing callers pass a valid pointer as the argument.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The init/exit() of the driver only calls platform_driver_{un}register(),
so it can be simpilfied by using module_platform_driver().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If of_parse_phandle_with_args() called from __thermal_of_bind() or
__thermal_of_unbind() fails, cooling_spec.np will not be initialized,
so move the of_node_put() calls below the respective return value checks
to avoid dereferencing an uninitialized pointer.
Fixes: 3fd6d6e2b4e8 ("thermal/of: Rework the thermal device tree initialization")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Check if BPMP supports thermal trip points, and if not,
do not expose the .set_trips callback to the thermal core
framework. This can happen in virtualized environments
where asynchronous communication with VM BPMP drivers is not
available.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221129153914.2699041-1-cyndis@kapsi.fi
|
|
This reworks the ACPI thermal driver to use a table of generic trip
point structures on top of the internal representation of trip points
and removes thermal zone callbacks that are not necessary any more
from it.
It requires some relatively small changes to be made in the thermal core
too and it is based on top of changes reworking ACPI device notification
handling that are included in this merge.
* acpi-thermal: (24 commits)
ACPI: thermal: Eliminate code duplication from acpi_thermal_notify()
ACPI: thermal: Drop unnecessary thermal zone callbacks
ACPI: thermal: Rework thermal_get_trend()
ACPI: thermal: Use trip point table to register thermal zones
thermal: core: Rework and rename __for_each_thermal_trip()
ACPI: thermal: Introduce struct acpi_thermal_trip
ACPI: thermal: Carry out trip point updates under zone lock
ACPI: thermal: Clean up acpi_thermal_register_thermal_zone()
thermal: core: Add priv pointer to struct thermal_trip
thermal: core: Introduce thermal_zone_device_exec()
thermal: core: Do not handle trip points with invalid temperature
ACPI: thermal: Drop redundant local variable from acpi_thermal_resume()
ACPI: thermal: Do not attach private data to ACPI handles
ACPI: thermal: Drop enabled flag from struct acpi_thermal_active
ACPI: thermal: Drop nocrt parameter
ACPI: thermal: Install Notify() handler directly
ACPI: NFIT: Remove unnecessary .remove callback
ACPI: NFIT: Install Notify() handler directly
ACPI: HED: Install Notify() handler directly
ACPI: battery: Install Notify() handler directly
...
|
|
These fix a few issues in the Intel DTS IOSF thermal driver, clean up
code in it and make it use trip point tables for registering thermal
zones.
* thermal-intel:
thermal: intel: intel_soc_dts_iosf: Use struct thermal_trip
thermal: intel: intel_soc_dts_iosf: Rework critical trip setup
thermal: intel: intel_soc_dts_iosf: Add helper for resetting trip points
thermal: intel: intel_soc_dts_iosf: Change initialization ordering
thermal: intel: intel_soc_dts_iosf: Pass sensors to update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Untangle update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Always assume notification support
thermal: intel: intel_soc_dts_iosf: Drop redundant symbol definition
thermal: intel: intel_soc_dts_iosf: Always use 2 trips
|
|
Rework the currently unused __for_each_thermal_trip() to pass original
pointers to struct thermal_trip objects to the callback, so it can be
used for updating trip data (e.g. temperatures), rename it to
for_each_thermal_trip() and make it available to modular drivers.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce a new helper function, thermal_zone_device_exec(), that can
be used by drivers to run a given callback routine under the zone lock.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch adds the support for Loongson-2 thermal sensor controller,
which can support maximum four sensor selectors that corresponding to four
sets of thermal control registers and one set of sampling register. The
sensor selector can selector a speific thermal sensor as temperature input.
The sampling register is used to obtain the temperature in real time, the
control register GATE field is used to set the threshold of high or low
temperature, when the input temperature is higher than the high temperature
threshold or lower than the low temperature threshold, an interrupt will
occur.
Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230817021007.10350-1-zhuyinbo@loongson.cn
|
|
Use IS_ERR_OR_NULL() to detect an error pointer or a null pointer
open-coding to simplify the code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230817014900.3094512-1-lizetao1@huawei.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230814180921.3336-1-aboutphysycs@gmail.com
|
|
platform_set_drvdata()
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811191548.3340-1-aboutphysycs@gmail.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811192847.3838-1-aboutphysycs@gmail.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811194032.4240-1-aboutphysycs@gmail.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230809154813.16033-1-aboutphysycs@gmail.com
|
|
Currently, when a controller is configured to use filtered mode, thermal
readings are valid only about 30% of the time.
Upon testing, it was noticed that lowering any of the interval settings
resulted in an improved rate of valid data. The same was observed when
decreasing the number of samples for each sensor (which also results in
quicker measurements).
Retrying the read with a timeout longer than the time it takes to
resample (about 344us with these settings and 4 sensors) also improves
the rate.
Lower all timing settings to the minimum, configure the filtering to
single sample, and poll the measurement register for at least one period
to improve the data validity on filtered mode. With these changes in
place, out of 100000 reads, a single one failed, ie 99.999% of the data
was valid.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230713154743.611870-1-nfraprado@collabora.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230810112344.3806-1-aboutphysycs@gmail.com
|
|
platform_set_drvdata()
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230810112015.3578-1-aboutphysycs@gmail.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230810111330.3248-1-aboutphysycs@gmail.com
|
|
'soc' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
exynos_tmu.c:890:14: error: cast to smaller integer type 'enum soc_type' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230810091318.70261-1-krzysztof.kozlowski@linaro.org
|
|
The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230809101439.2663042-1-ruanjinjie@huawei.com
|
|
Referring to platform_get_irq()'s definition, the return value has
already been checked if ret < 0, and printed via dev_err_probe().
Calling dev_err_probe() one more time outside platform_get_irq()
is obviously redundant.
Removing dev_err_probe() outside platform_get_irq() to clean up
above problem.
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230802094527.988842-1-chenjiahao16@huawei.com
|
|
The sun8i thermal driver reads calibration data via the nvmem API at
startup, updating the device configuration and not referencing the data
again. Rather than explicitly freeing the nvmem data the driver relies
on devm_ to release it, even though the data is never referenced again.
The allocation is still tracked so it's not leaked but this is notable
when looking at the code and is a little wasteful so let's instead
explicitly free the nvmem after we're done with it.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230719-thermal-sun8i-free-nvmem-v1-1-f553d5afef79@kernel.org
|
|
It's redundant, let's remove it.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230626125515.18830-1-frank.li@vivo.com
|
|
This patch fixes the following sparse warnings:
drivers/thermal/qcom/tsens-v1.c:24:40: sparse: warning: symbol 'tsens_qcs404_nvmem' was not declared. Should it be static?
drivers/thermal/qcom/tsens-v0_1.c:26:40: sparse: warning: symbol 'tsens_8916_nvmem' was not declared. Should it be static?
drivers/thermal/qcom/tsens-v0_1.c:42:40: sparse: warning: symbol 'tsens_8974_nvmem' was not declared. Should it be static?
drivers/thermal/qcom/tsens-v0_1.c:64:40: sparse: warning: symbol 'tsens_8974_backup_nvmem' was not declared. Should it be static?
No functional change intended.
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230713160415.149381-1-minhuadotchen@gmail.com
|
|
nvmem_cell_read_u32() may return -EPROBE_DEFER if NVMEM supplier has not
yet been probed. Future reprobe may succeed, so printing:
i.mx8mm_thermal 30260000.tmu: Failed to read OCOTP nvmem cell (-517).
to the log is confusing. Fix this by using dev_err_probe. This also
elevates the message from warning to error, which is more correct: The
log message is only ever printed in probe error path and probe aborts
afterwards, so it really warrants an error-level message.
Fixes: 403291648823 ("thermal/drivers/imx: Add support for loading calibration data from OCOTP")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230708112647.2897294-1-a.fatoum@pengutronix.de
|
|
The documentation says "If an error occurs, ERR_PTR(-ERROR) will be
returned" but the current code checks against a NULL pointer returned.
Fix this by checking if IS_ERR().
Signed-off-by: Minjie Du <duminjie@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230713042413.2519-1-duminjie@vivo.com
|
|
Each LVTS thermal controller can have up to four sensors, each capable
of triggering its own interrupt when its measured temperature crosses
the configured threshold. The threshold for each sensor is handled
separately by the thermal framework, since each one is registered with
its own thermal zone and trips. However, the temperature thresholds are
configured on the controller, and therefore are shared between all
sensors on that controller.
When the temperature measured by the sensors is different enough to
cause the thermal framework to configure different thresholds for each
one, interrupts start triggering on sensors outside the last threshold
configured.
To address the issue, track the thresholds required by each sensor and
only actually set the highest one in the hardware, and disable
interrupts for all sensors outside the current configured range.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-7-nfraprado@collabora.com
|
|
The thermal framework might leave the low threshold unset if there
aren't any lower trip points. This leaves the register zeroed, which
translates to a very high temperature for the low threshold. The
interrupt for this threshold is then immediately triggered, and the
state machine gets stuck, preventing any other temperature monitoring
interrupts to ever trigger.
(The same happens by not setting the Cold or Hot to Normal thresholds
when using those)
Set the unused threshold to a valid low value. This value was chosen so
that for any valid golden temperature read from the efuse, when the
value is converted to raw and back again to milliCelsius, the result
doesn't underflow.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-6-nfraprado@collabora.com
|
|
Out of the many interrupts supported by the hardware, the only ones of
interest to the driver currently are:
* The temperature went over the high offset threshold, for any of the
sensors
* The temperature went below the low offset threshold, for any of the
sensors
* The temperature went over the stage3 threshold
These are the only thresholds configured by the driver through the
OFFSETH, OFFSETL, and PROTTC registers, respectively.
The current interrupt mask in LVTS_MONINT_CONF, enables many more
interrupts, including data ready on sensors for both filtered and
immediate mode. These are not only not handled by the driver, but they
are also triggered too often, causing unneeded overhead. Disable these
unnecessary interrupts.
The meaning of each bit can be seen in the comment describing
LVTS_MONINTST in the IRQ handler.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-5-nfraprado@collabora.com
|
|
There are two kinds of temperature monitoring interrupts available:
* High Offset, Low Offset
* Hot, Hot to normal, Cold
The code currently uses the hot/h2n/cold interrupts, however in a way
that doesn't work: the cold threshold is left uninitialized, which
prevents the other thresholds from ever triggering, and the h2n
interrupt is used as the lower threshold, which prevents the hot
interrupt from triggering again after the thresholds are updated by the
thermal framework, since a hot interrupt can only trigger again after
the hot to normal interrupt has been triggered.
But better yet than addressing those issues, is to use the high/low
offset interrupts instead. This way only two thresholds need to be
managed, which have a simpler state machine, making them a better match
to the thermal framework's high and low thresholds.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-4-nfraprado@collabora.com
|
|
Each controller can be configured to operate on immediate or filtered
mode. On filtered mode, the sensors are enabled by setting the
corresponding bits in MONCTL0, while on immediate mode, by setting
MSRCTL1.
Previously, the code would set MSRCTL1 for all four sensors when
configured to immediate mode, but given that the controller might not
have all four sensors connected, this would cause interrupts to trigger
for non-existent sensors. Fix this by handling the MSRCTL1 register
analogously to the MONCTL0: only enable the sensors that were declared.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-3-nfraprado@collabora.com
|
|
There is a single IRQ handler for each LVTS thermal domain, and it is
supposed to check each of its underlying controllers for the origin of
the interrupt and clear its status. However due to a typo, only the
first controller was ever being handled, which resulted in the interrupt
never being cleared when it happened on the other controllers. Add the
missing index so interrupts are handled for all controllers.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-2-nfraprado@collabora.com
|
|
Because the number of trip points in each thermal zone and their
types are known to intel_soc_dts_iosf_init() prior to the registration
of the thermal zones, make it create an array of struct thermal_trip
entries in each struct intel_soc_dts_sensor_entry object and make
add_dts_thermal_zone() use thermal_zone_device_register_with_trips()
for thermal zone registration and pass that array as its second
argument.
Drop the sys_get_trip_temp() and sys_get_trip_type() callback
functions along with the respective callback pointers in
tzone_ops, because they are not necessary any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Critical trip points appear in the DTS thermal zones only after those
thermal zones have been registered via intel_soc_dts_iosf_init().
Moreover, they are "created" by changing the type of an existing trip
point from THERMAL_TRIP_PASSIVE to THERMAL_TRIP_CRITICAL via
intel_soc_dts_iosf_add_read_only_critical_trip(), the caller of which
has to be careful enough to pass at least 1 as the number of read-only
trip points to intel_soc_dts_iosf_init() beforehand.
This is questionable, because user space may have started to use the
trips at the time when intel_soc_dts_iosf_add_read_only_critical_trip()
runs and there is no synchronization between it and sys_set_trip_temp().
To address it, use the observation that nonzero number of read-only
trip points is only passed to intel_soc_dts_iosf_init() when critical
trip points are going to be used, so in fact that function may get all
of the information regarding the critical trip points upfront and it
can configure them before registering the corresponding thermal zones.
Accordingly, replace the read_only_trip_count argument of
intel_soc_dts_iosf_init() with a pair of new arguments related to
critical trip points: a bool one indicating whether or not critical
trip points are to be used at all and an int one representing the
critical trip point temperature offset relative to Tj_max. Use these
arguments to configure the critical trip points before the registration
of the thermal zones and to compute the number of writeable trip points
in add_dts_thermal_zone().
Modify both callers of intel_soc_dts_iosf_init() to take these changes
into account and drop the intel_soc_dts_iosf_add_read_only_critical_trip()
call, that is not necessary any more, from intel_soc_thermal_init(),
which also allows it to return success right after requesting the IRQ.
Finally, drop intel_soc_dts_iosf_add_read_only_critical_trip()
altogether, because it does not have any more users.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Because trip points are reset for each sensor in two places in the
same way, add a helper function for that to reduce code duplication
a bit.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
The initial configuration of trip points in intel_soc_dts_iosf_init()
takes place after registering the sensor thermal zones which is
potentially problematic, because it may race with the setting of trip
point temperatures via sysfs, as there is no synchronization between it
and sys_set_trip_temp().
To address this, change the initialization ordering so that the trip
points are configured prior to the registration of thermal zones.
Accordingly, change the cleanup ordering in intel_soc_dts_iosf_exit()
to remove the thermal zones before resetting the trip points.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
After previous changes, update_trip_temp() only uses its dts argument to
get to the sensors field in the struct intel_soc_dts_sensor_entry object
pointed to by that argument, so pass the value of that field directly to
it instead.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Function update_trip_temp() is currently used for the initialization
of trip points as well as for changing trip point temperatures in
sys_set_trip_temp().
This is quite confusing and passing the value of dts->trip_types[trip]
to it so that it can store that value in the same memory location is
not particularly useful, because it only is necessary to set the
trip point type once, at the initialization time.
For this reason, drop the last argument from update_trip_temp() and
introduce configure_trip() calling the former internally for the
initial configuration of trip points.
Modify the majority of update_trip_temp() callers to use
configure_trip() instead of it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
None of the existing callers of intel_soc_dts_iosf_init() passes
INTEL_SOC_DTS_INTERRUPT_NONE as the first argument to it, so the
notification local variable in it is always true and the
notification_support argument of add_dts_thermal_zone() is always
true either.
For this reason, drop the notification local variable from
intel_soc_dts_iosf_init() and the notification_support argument from
add_dts_thermal_zone() and rearrange the latter to always set
writable_trip_cnt and trip_mask.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
SOC_MAX_DTS_SENSORS is already defined in intel_soc_dts_iosf.h which is
included in intel_soc_dts_iosf.c, so it does not need to be defined in
the latter again.
Drop the redundant definition of that symbol from intel_soc_dts_iosf.c.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Both the existing callers of intel_soc_dts_iosf_init() pass 2 as the trip
count argument, so it can be replaced with SOC_MAX_DTS_TRIPS everywhere in
the code and the trip_count argument of that function can be dropped.
This also allows the trip_count field to be dropped from struct
intel_soc_dts_sensor_entry, as it is always equal to 2, and some
related code can be simplified.
Make changes accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
