summaryrefslogtreecommitdiff
path: root/drivers/spi/Kconfig
AgeCommit message (Collapse)AuthorFilesLines
2014-03-30Merge remote-tracking branches 'spi/topic/drivers', 'spi/topic/dw', ↵Mark Brown1-1/+2
'spi/topic/efm32', 'spi/topic/ep93xx', 'spi/topic/fsl', 'spi/topic/fsl-dspi', 'spi/topic/fsl-espi' and 'spi/topic/gpio' into spi-next
2014-03-30Merge remote-tracking branches 'spi/topic/bus-num', 'spi/topic/cleanup', ↵Mark Brown1-1/+1
'spi/topic/clps711x', 'spi/topic/coldfire', 'spi/topic/completion' and 'spi/topic/davinci' into spi-next
2014-03-27spi: clps711x: Enable driver compilation with COMPILE_TESTAxel Lin1-1/+1
This helps increasing build testing coverage. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-16spi/fsl-dspi: Convert to use regmap and add big-endian supportChao Fu1-0/+1
Freescale DSPI module will have two endianess in different platform, but ARM is little endian. So when DSPI in big endian, core in little endian, readl and writel can not adjust R/W register in this condition. This patch will remove general readl/writel, and import regmap mechanism. Data endian will be transfered in regmap APIs. Documents: dspi add bool "big-endian" in dts node if DSPI module work in big endian. Signed-off-by: Chao Fu <b44548@freescale.com> Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-04spi: rspi: Document support for Renesas QSPI in KconfigGeert Uytterhoeven1-2/+2
As of commit 5ce0ba88650f2606244a761d92e2b725f4ab3583 ("spi: rcar: add Renesas QSPI support on RSPI") the rspi driver handles Renesas QSPI, too, but this was not reflected in the Kconfig help text. Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-03spi: dw-mmio: remove HAVE_CLK build dependecyBaruch Siach1-1/+1
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h like this platform driver needs not depend on HAVE_CLK. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-26Merge tag 'spi-v3.14-2' of ↵Linus Torvalds1-3/+11
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Pull spi updates from Mark Brown: "A respun version of the merges for the pull request previously sent with a few additional fixes. The last two merges were fixed up by hand since the branches have moved on and currently have the prior merge in them. Quite a busy release for the SPI subsystem, mostly in cleanups big and small scattered through the stack rather than anything else: - New driver for the Broadcom BC63xx HSSPI controller - Fix duplicate device registration for ACPI - Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA changes upon which the transiton depends) - Some small optimisations to reduce the amount of time we hold locks in the datapath, eliminate some redundant checks and the size of a spi_transfer - Lots of fixes, cleanups and general enhancements to drivers, especially the rspi and Atmel drivers" * tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits) spi: core: Fix transfer failure when master->transfer_one returns positive value spi: Correct set_cs() documentation spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer() spi: Spelling s/finised/finished/ spi: sc18is602: Convert to use bits_per_word_mask spi: Remove duplicate code to set default bits_per_word setting spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP spi: clps711x: Add MODULE_ALIAS to support module auto-loading spi: rspi: Add missing clk_disable() calls in error and cleanup paths spi: rspi: Spelling s/transmition/transmission/ spi: rspi: Add support for specifying CPHA/CPOL spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match spi: rspi: Add more QSPI register documentation spi: rspi: Add more RSPI register documentation spi: rspi: Remove dependency on DMAE for SHMOBILE spi/s3c64xx: Correct indentation spi: sh: Use spi_sh_clear_bit() instead of open-coded spi: bitbang: Grammar s/make to make/to make/ spi: sh-hspi: Spelling s/recive/receive/ spi: core: Improve tx/rx_nbits check comments ...
2014-01-24Merge tag 'cleanup-for-linus' of ↵Linus Torvalds1-0/+3
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC cleanups from Olof Johansson: "This is the branch where we usually queue up cleanup efforts, moving drivers out of the architecture directory, header file restructuring, etc. Sometimes they tangle with new development so it's hard to keep it strictly to cleanups. Some of the things included in this branch are: * Atmel SAMA5 conversion to common clock * Reset framework conversion for tegra platforms - Some of this depends on tegra clock driver reworks that are shared with Mike Turquette's clk tree. * Tegra DMA refactoring, which are shared branches with the DMA tree. * Removal of some header files on exynos to prepare for multiplatform" * tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits) ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h ARM: mvebu: remove prototypes of non-existing functions from common.h ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h serial: sh-sci: Rework baud rate calculation serial: sh-sci: Compute overrun_bit without using baud rate algo serial: sh-sci: Remove unused GPIO request code serial: sh-sci: Move overrun_bit and error_mask fields out of pdata serial: sh-sci: Support resources passed through platform resources serial: sh-sci: Don't check IRQ in verify port operation serial: sh-sci: Set the UPF_FIXED_PORT flag serial: sh-sci: Remove duplicate interrupt check in verify port op serial: sh-sci: Simplify baud rate calculation algorithms serial: sh-sci: Remove baud rate calculation algorithm 5 serial: sh-sci: Sort headers alphabetically ARM: EXYNOS: Kill exynos_pm_late_initcall() ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4 ARM: at91: switch Calao QIL-A9260 board to DT clk: at91: fix pmc_clk_ids data type attriubte PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h> ARM: EXYNOS: remove <mach/regs-clock.h> for exynos ...
2014-01-23Merge remote-tracking branches 'spi/topic/pxa2xx', 'spi/topic/qspi', ↵Mark Brown1-1/+1
'spi/topic/s3c24xx', 'spi/topic/s3c64xx', 'spi/topic/sh', 'spi/topic/tegra114', 'spi/topic/tegra20-sflash', 'spi/topic/tegra20-slink', 'spi/topic/txx9' and 'spi/topic/xcomm' into spi-linus
2014-01-23Merge remote-tracking branches 'spi/topic/fsl-espi', 'spi/topic/gpio', ↵Mark Brown1-1/+3
'spi/topic/hspi', 'spi/topic/mpc512x', 'spi/topic/msiof', 'spi/topic/nuc900', 'spi/topic/oc-tiny', 'spi/topic/omap', 'spi/topic/orion' and 'spi/topic/pci' into spi-linus
2014-01-23Merge remote-tracking branches 'spi/topic/bcm2835', 'spi/topic/bcm63xx', ↵Mark Brown1-2/+8
'spi/topic/bcm63xx-hsspi', 'spi/topic/bitbang', 'spi/topic/bpw', 'spi/topic/clps711x', 'spi/topic/coldfire', 'spi/topic/davinci', 'spi/topic/dw' and 'spi/topic/falcon' into spi-linus
2014-01-13spi: rspi: Remove dependency on DMAE for SHMOBILEGeert Uytterhoeven1-1/+1
On ARM-based SHMOBILE, the rspi driver builds and works fine without the DMA controller driver, hence relax the dependencies. Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-09spi/davinci: Don't select EDMASekhar Nori1-1/+0
There is no need to force selection of TI EDMA DMA engine driver when DaVinci SPI driver is selected. The driver builds just fine even with CONFIG_TI_EDMA disabled. Forcing this selection causes warnings of the sort: warning: (ARCH_KEYSTONE && SPI_DAVINCI) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE)) This reverts commit b5f14330590118e6a0659255476c0f24ab681e05. Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-12spi: tegra: use reset frameworkStephen Warren1-0/+3
Tegra's clock driver now provides an implementation of the common reset API (include/linux/reset.h). Use this instead of the old Tegra- specific API; that will soon be removed. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Mark Brown <broonie@linaro.org> Reviewed-by: Thierry Reding <treding@nvidia.com>
2013-12-04spi: bcm63xx-hsspi: add bcm63xx HSSPI driverJonas Gorski1-0/+7
Add a driver for the High Speed SPI controller found on newer BCM63XX SoCs. It does feature some new modes like 3-wire or dual spi, but neither of it is currently implemented. Signed-off-by: Jonas Gorski <jogo@openwrt.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27spi: sh-msiof: Enable driver compilation with COMPILE_TESTLaurent Pinchart1-1/+2
This helps increasing build testing coverage. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-24spi: s3c64xx: Always select S3C64XX_PL080 when ARCH_S3C64XX is enabledTomasz Figa1-1/+1
The legacy S3C64xx DMA driver has been removed, DMA support on S3C64xx is provided only by the generic PL08x driver. This patch modifies the Kconfig entry of spi-s3c64xx driver, which relies on availability of DMA, to always select the S3C64XX_PL080 symbol. Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-24spi: s3c64xx: Do not require legacy DMA API in case of S3C64XXTomasz Figa1-1/+1
With support for amba-pl08x driver, on S3C64xx the generic DMA engine API can be used instead of the private s3c-dma interface. Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-24spi: omap2: Add build dependencies for writel_relaxed()Mark Brown1-0/+1
It's not reliably available. Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-25Merge remote-tracking branch 'spi/topic/rspi' into spi-nextMark Brown1-1/+1
2013-10-25Merge remote-tracking branch 'spi/topic/loop' into spi-nextMark Brown1-1/+1
2013-09-26spi: s3c64xx: Allow build on all Samsung platformsMateusz Krawczuk1-1/+1
Replace all symbols by simple dependency PLAT_SAMSUNG. Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-09-17spi: rcar: add Renesas QSPI support on RSPIHiep Cao Minh1-1/+1
The R8A7790 has QSPI module which is very similar to RSPI. This patch adds into RSPI module together to supports QSPI module. Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-09-17spi: fsl-dspi: several minor improvements and fixesUwe Kleine-König1-0/+1
- improve dependencies using COMPILE_TEST - fix a typo - drop platform_set_drvdata(pdev, NULL) in error path of probe - make MODULE_LICENSE match the header Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-09-13Remove GENERIC_HARDIRQ config optionMartin Schwidefsky1-2/+1
After the last architecture switched to generic hard irqs the config options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code for !CONFIG_GENERIC_HARDIRQS can be removed. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2013-09-01Merge remote-tracking branch 'spi/topic/sirf' into spi-nextMark Brown1-1/+1
2013-09-01Merge remote-tracking branch 'spi/topic/qspi' into spi-nextMark Brown1-0/+8
2013-09-01Merge remote-tracking branch 'spi/topic/efm32' into spi-nextMark Brown1-0/+7
2013-09-01Merge remote-tracking branch 'spi/topic/dspi' into spi-nextMark Brown1-0/+7
2013-09-01Merge remote-tracking branch 'spi/topic/davinci' into spi-nextMark Brown1-1/+1
2013-09-01Merge remote-tracking branch 'spi/topic/build' into spi-nextMark Brown1-14/+14
2013-08-22spi/qspi: Add qspi flash controllerSourav Poddar1-0/+8
The patch add basic support for the quad spi controller. QSPI is a kind of spi module that allows single, dual and quad read access to external spi devices. The module has a memory mapped interface which provide direct interface for accessing data form external spi devices. The patch will configure controller clocks, device control register and for defining low level transfer apis which will be used by the spi framework to transfer data to the slave spi device(flash in this case). Test details: ------------- Tested this on dra7 board. Test1: Ran mtd_stesstest for 40000 iterations. - All iterations went through without failure. Test2: Use mtd utilities: - flash_erase to erase the flash device - mtd_debug read to read data back. - mtd_debug write to write to the data flash. diff between the write and read data shows zero. Acked-by: Felipe Balbi<balbi@ti.com> Reviewed-by: Felipe Balbi<balbi@ti.com> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-08-22spi:Add Freescale DSPI driver for Vybrid VF610 platformChao Fu1-0/+7
The serial peripheral interface (SPI) module implemented on Freescale Vybrid platform provides a synchronous serial bus for communication between Vybrid and the external peripheral device. The SPI supports full-duplex, three-wire synchronous transfer, has TX/RX FIFO with depth of four entries. This driver is the SPI master mode driver and has been tested on Vybrid VF610TWR board. Signed-off-by: Alison Wang <b18965@freescale.com> Signed-off-by: Chao Fu <b44548@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-08-09spi: new controller driver for efm32 SoCsUwe Kleine-König1-0/+7
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-08-06spi/build: Remove SPI_SIRF from compile testMark Brown1-1/+1
It now needs the architecture dependant DMA driver. Signed-off-by: Mark Brown <broonie@linaro.org>
2013-08-06spi/sirf: Depends on SIRF_DMAMark Brown1-1/+1
Now that DMA support has been added to the driver it needs the architecture DMA driver to be built in order to link. Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-29spi/drivers: Enable build of drivers with COMPILE_TESTMark Brown1-14/+14
Enable the build of drivers which don't have any real build time dependency on their architecture or platform with COMPILE_TEST, providing better build time coverage. Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-25spi: davinci: Update configs to make it selectable on KeystoneSantosh Shilimkar1-1/+1
Keystone2 SOCs share the SPI IP block with DaVinci based SOCs. Update the config bits so that its usable on Keystone2 based SOCs. Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-15spi/rspi: Add missing dependency on DMAEMark Brown1-1/+1
The filter function used by the rspi driver is part of the DMAE controller driver so if the DMA controller driver is somehow disabled then the rspi driver will fail to build. Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-15spi: add spi controller v3 master driver for BlackfinScott Jiang1-1/+8
New spi controller(version 3) is integrated into Blackfin 60x processor. Comparing to bf5xx spi controller, we support 32 bits word size and independent receive and transmit DMA channels now. Also mode 0 and 2 (CPHA = 0) can get fully supported becasue cs line may be controlled by the software. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-14Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds1-1/+1
Pull MIPS updates from Ralf Baechle: "MIPS updates: - All the things that didn't make 3.10. - Removes the Windriver PPMC platform. Nobody will miss it. - Remove a workaround from kernel/irq/irqdomain.c which was there exclusivly for MIPS. Patch by Grant Likely. - More small improvments for the SEAD 3 platform - Improvments on the BMIPS / SMP support for the BCM63xx series. - Various cleanups of dead leftovers. - Platform support for the Cavium Octeon-based EdgeRouter Lite. Two large KVM patchsets didn't make it for this pull request because their respective authors are vacationing" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits) MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions MIPS: SEAD3: Disable L2 cache on SEAD-3. MIPS: BCM63xx: Enable second core SMP on BCM6328 if available MIPS: BCM63xx: Add SMP support to prom.c MIPS: define write{b,w,l,q}_relaxed MIPS: Expose missing pci_io{map,unmap} declarations MIPS: Malta: Update GCMP detection. Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET" MIPS: APSP: Remove <asm/kspd.h> SSB: Kconfig: Amend SSB_EMBEDDED dependencies MIPS: microMIPS: Fix improper definition of ISA exception bit. MIPS: Don't try to decode microMIPS branch instructions where they cannot exist. MIPS: Declare emulate_load_store_microMIPS as a static function. MIPS: Fix typos and cleanup comment MIPS: Cleanup indentation and whitespace MIPS: BMIPS: support booting from physical CPU other than 0 MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS MIPS: GIC: Fix gic_set_affinity infinite loop MIPS: Don't save/restore OCTEON wide multiplier state on syscalls. ...
2013-06-20ARM: sirf: use CONFIG_SIRF rather than CONFIG_PRIMA2 where necessaryArnd Bergmann1-1/+1
I got a build error today that made me realize that it is not possible to build a kernel for a SiRF platform without enabling CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2. This fixes all occurences that appear like common SiRF code. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Mark Brown <broonie@linaro.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Barry Song <Baohua.Song@csr.com> Acked-by: Mike Turquette <mturquette@linaro.org>
2013-06-10MIPS: OCTEON: Rename Kconfig CAVIUM_OCTEON_REFERENCE_BOARD to CAVIUM_OCTEON_SOCDavid Daney1-1/+1
CAVIUM_OCTEON_SOC most place we used to use CPU_CAVIUM_OCTEON. This allows us to CPU_CAVIUM_OCTEON in places where we have no OCTEON SOC. Remove CAVIUM_OCTEON_SIMULATOR as it doesn't really do anything, we can get the same configuration with CAVIUM_OCTEON_SOC. Signed-off-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: linux-ide@vger.kernel.org Cc: linux-edac@vger.kernel.org Cc: linux-i2c@vger.kernel.org Cc: netdev@vger.kernel.org Cc: spi-devel-general@lists.sourceforge.net Cc: devel@driverdev.osuosl.org Cc: linux-usb@vger.kernel.org Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Patchwork: https://patchwork.linux-mips.org/patch/5295/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-05-09Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linuxLinus Torvalds1-4/+4
Pull removal of GENERIC_GPIO from Grant Likely: "GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it is possible to do so which has been causing confusion and breakage. This branch does the work to completely eliminate GENERIC_GPIO." * tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: gpio: update gpio Chinese documentation Remove GENERIC_GPIO config option Convert selectors of GENERIC_GPIO to GPIOLIB blackfin: force use of gpiolib m68k: coldfire: use gpiolib mips: pnx833x: remove requirement for GENERIC_GPIO openrisc: default GENERIC_GPIO to false avr32: default GENERIC_GPIO to false xtensa: remove explicit selection of GENERIC_GPIO sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB powerpc: remove redundant GENERIC_GPIO selection unicore32: default GENERIC_GPIO to false unicore32: remove unneeded select GENERIC_GPIO arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB arm: remove redundant GENERIC_GPIO selection mips: alchemy: require gpiolib mips: txx9: change GENERIC_GPIO to GPIOLIB mips: loongson: use GPIO driver on CONFIG_GPIOLIB mips: remove redundant GENERIC_GPIO select
2013-04-30Merge tag 'spi-v3.10' of ↵Linus Torvalds1-2/+28
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Pull spi updates from Mark Brown: "A fairly quiet release for SPI, mainly driver work. A few highlights: - Supports bits per word compatibility checking in the core. - Allow use of the IP used in Freescale SPI controllers outside Freescale SoCs. - DMA support for the Atmel SPI driver. - New drivers for the BCM2835 and Tegra114" * tag 'spi-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (68 commits) spi-topcliff-pch: fix to use list_for_each_entry_safe() when delete list items spi-topcliff-pch: missing platform_driver_unregister() on error in pch_spi_init() ARM: dts: add pinctrl property for spi node for atmel SoC ARM: dts: add spi nodes for the atmel boards ARM: dts: add spi nodes for atmel SoC ARM: at91: add clocks for spi dt entries spi/spi-atmel: add dmaengine support spi/spi-atmel: add flag to controller data for lock operations spi/spi-atmel: add physical base address spi/sirf: fix MODULE_DEVICE_TABLE MAINTAINERS: Add git repository and update my address spi/s3c64xx: Check for errors in dmaengine prepare_transfer() spi/s3c64xx: Fix non-dmaengine usage spi: omap2-mcspi: fix error return code in omap2_mcspi_probe() spi/s3c64xx: let device core setup the default pin configuration MAINTAINERS: Update Grant's email address and maintainership spi: omap2-mcspi: Fix transfers if DMADEVICES is not set spi: s3c64xx: move to generic dmaengine API spi-gpio: init CS before spi_bitbang_setup() spi: spi-mpc512x-psc: let transmiter/receiver enabled when in xfer loop ...
2013-04-16Convert selectors of GENERIC_GPIO to GPIOLIBAlexandre Courbot1-4/+4
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca>
2013-04-07spi/tegra114: add spi driverLaxman Dewangan1-0/+8
Add SPI driver for NVIDIA's Tegra114 SPI controller. This controller is different than the older SoCs SPI controller in internal design as well as register interface. This driver supports the: - non DMA based transfer for smaller transfer i.e. less than FIFO depth. - APB DMA based transfer for larger transfer i.e. more than FIFO depth. - Clock gating through runtime PM callbacks. - registration through DT only. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2013-04-07spi/spi-fsl-spi: Add support for Aeroflex Gaisler GRLIB cores normally ↵Andreas Larsson1-1/+3
running on SPARC This adds support for the mostly register-compatible SPICTRL cores from the GRLIB VHDL IP core library from Aeroflex Gaisler. They are normally running on SPARC. A different entry in of_fsl_spi_match matches this core and indicates a different hardware type that is used to set up different function pointers and special cases. The GRLIB core operates in cpu mode. The number of bits per word might be limited. There might be native chipselects selected via a slave select register. These differences to the FSL type cores, if present, are indicated by a capabilities register. Other register and function differences exists but are not relevant to the driver. Acked-by: Anton Vorontsov <anton@enomsg.org> Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2013-04-07spi/spi-fsl-spi: Make driver usable in CPU mode outside of an FSL_SOC ↵Andreas Larsson1-1/+6
environment This makes the spi-fsl-spi driver usable in CPU mode outside of an FSL_SOC and even an powerpc environment by moving CPM mode functionality to a separate file that is only compiled and linked in an FSL_SOC environment and adding some ifdefs to hide types and functions or provide alternatives. For devicetree probing a "clock-frequency" property is used for clock frequency instead of calls to FSL_SOC-specific functions. Acked-by: Anton Vorontsov <anton@enomsg.org> Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2013-03-21drivers/Kconfig: add several missing GENERIC_HARDIRQS dependenciesHeiko Carstens1-1/+2
With this patch an allmodconfig finally builds on s390 again. Fixes these build errors: ERROR: "devm_request_threaded_irq" [drivers/spi/spi-altera.ko] undefined! ERROR: "devm_request_threaded_irq" [drivers/media/platform/sh_veu.ko] undefined! ERROR: "devm_request_threaded_irq" [drivers/dma/dw_dmac.ko] undefined! Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-01-11 16:01:23 +0300