| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Reserve ECAM so we don't assign it to PCI BARs; this works around
bugs where BIOS included ECAM in a PNP0A03 host bridge window,
didn't reserve it via a PNP0C02 motherboard device, and didn't
allocate space for SR-IOV VF BARs (Bjorn Helgaas)
- Add MMCONFIG/ECAM debug logging (Bjorn Helgaas)
- Rename 'MMCONFIG' to 'ECAM' to match spec usage (Bjorn Helgaas)
- Log device type (Root Port, Switch Port, etc) during enumeration
(Bjorn Helgaas)
- Log bridges before downstream devices so the dmesg order is more
logical (Bjorn Helgaas)
- Log resource names (BAR 0, VF BAR 0, bridge window, etc)
consistently instead of a mix of names and "reg 0x10" (Puranjay
Mohan, Bjorn Helgaas)
- Fix 64GT/s effective data rate calculation to use 1b/1b encoding
rather than the 8b/10b or 128b/130b used by lower rates (Ilpo
Järvinen)
- Use PCI_HEADER_TYPE_* instead of literals in x86, powerpc, SCSI
lpfc (Ilpo Järvinen)
- Clean up open-coded PCIBIOS return code mangling (Ilpo Järvinen)
Resource management:
- Restructure pci_dev_for_each_resource() to avoid computing the
address of an out-of-bounds array element (the bounds check was
performed later so the element was never actually *read*, but it's
nicer to avoid even computing an out-of-bounds address) (Andy
Shevchenko)
Driver binding:
- Convert pci-host-common.c platform .remove() callback to
.remove_new() returning 'void' since it's not useful to return
error codes here (Uwe Kleine-König)
- Convert exynos, keystone, kirin from .remove() to .remove_new(),
which returns void instead of int (Uwe Kleine-König)
- Drop unused struct pci_driver.node member (Mathias Krause)
Virtualization:
- Add ACS quirk for more Zhaoxin Root Ports (LeoLiuoc)
Error handling:
- Log AER errors as "Correctable" (not "Corrected") or
"Uncorrectable" to match spec terminology (Bjorn Helgaas)
- Decode Requester ID when no error info found instead of printing
the raw hex value (Bjorn Helgaas)
Endpoint framework:
- Use a unique test pattern for each BAR in the pci_endpoint_test to
make it easier to debug address translation issues (Niklas Cassel)
Broadcom STB PCIe controller driver:
- Add DT property "brcm,clkreq-mode" and driver support for different
CLKREQ# modes to make ASPM L1.x states possible (Jim Quinlan)
Freescale Layerscape PCIe controller driver:
- Add suspend/resume support for Layerscape LS1043a and LS1021a,
including software-managed PME_Turn_Off and transitions between L0,
L2/L3_Ready Link states (Frank Li)
MediaTek PCIe controller driver:
- Clear MSI interrupt status before handler to avoid missing MSIs
that occur after the handler (qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 translation window setup to handle MMIO space
that is not a power of two in size (Jianjun Wang)
Qualcomm PCIe controller driver:
- Increase qcom iommu-map maxItems to accommodate SDX55 (five
entries) and SDM845 (sixteen entries) (Krzysztof Kozlowski)
- Describe qcom,pcie-sc8180x clocks and resets accurately (Krzysztof
Kozlowski)
- Describe qcom,pcie-sm8150 clocks and resets accurately (Krzysztof
Kozlowski)
- Correct the qcom "reset-name" property, previously incorrectly
called "reset-names" (Krzysztof Kozlowski)
- Document qcom,pcie-sm8650, based on qcom,pcie-sm8550 (Neil
Armstrong)
Renesas R-Car PCIe controller driver:
- Replace of_device.h with explicit of.h include to untangle header
usage (Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v
regulators on KingFisher (Wolfram Sang)
SiFive FU740 PCIe controller driver:
- Convert fu740 CONFIG_PCIE_FU740 dependency from SOC_SIFIVE to
ARCH_SIFIVE (Conor Dooley)
Synopsys DesignWare PCIe controller driver:
- Align iATU mapping for endpoint MSI-X (Niklas Cassel)
- Drop "host_" prefix from struct dw_pcie_host_ops members (Yoshihiro
Shimoda)
- Drop "ep_" prefix from struct dw_pcie_ep_ops members (Yoshihiro
Shimoda)
- Rename struct dw_pcie_ep_ops.func_conf_select() to
.get_dbi_offset() to be more descriptive (Yoshihiro Shimoda)
- Add Endpoint DBI accessors to encapsulate offset lookups (Yoshihiro
Shimoda)
TI J721E PCIe driver:
- Add j721e DT and driver support for 'num-lanes' for devices that
support x1, x2, or x4 Links (Matt Ranostay)
- Add j721e DT compatible strings and driver support for j784s4 (Matt
Ranostay)
- Make TI J721E Kconfig depend on ARCH_K3 since the hardware is
specific to those TI SoC parts (Peter Robinson)
TI Keystone PCIe controller driver:
- Hold power management references to all PHYs while enabling them to
avoid a race when one provides clocks to others (Siddharth
Vadapalli)
Xilinx XDMA PCIe controller driver:
- Remove redundant dev_err(), since platform_get_irq() and
platform_get_irq_byname() already log errors (Yang Li)
- Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
(Krzysztof Wilczyński)
- Fix xilinx_pl_dma_pcie_init_irq_domain() error return when
irq_domain_add_linear() fails (Harshit Mogalapalli)
MicroSemi Switchtec management driver:
- Do dma_mrpc cleanup during switchtec_pci_remove() to match its devm
ioremapping in switchtec_pci_probe(). Previously the cleanup was
done in stdev_release(), which used stale pointers if stdev->cdev
happened to be open when the PCI device was removed (Daniel
Stodden)
Miscellaneous:
- Convert interrupt terminology from "legacy" to "INTx" to be more
specific and match spec terminology (Damien Le Moal)
- In dw-xdata-pcie, pci_endpoint_test, and vmd, replace usage of
deprecated ida_simple_*() API with ida_alloc() and ida_free()
(Christophe JAILLET)"
* tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Fix kernel-doc issues
PCI: brcmstb: Configure HW CLKREQ# mode appropriate for downstream device
dt-bindings: PCI: brcmstb: Add property "brcm,clkreq-mode"
PCI: mediatek-gen3: Fix translation window size calculation
PCI: mediatek: Clear interrupt status before dispatching handler
PCI: keystone: Fix race condition when initializing PHYs
PCI: xilinx-xdma: Fix error code in xilinx_pl_dma_pcie_init_irq_domain()
PCI: xilinx-xdma: Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
PCI: rcar-gen4: Fix -Wvoid-pointer-to-enum-cast error
PCI: iproc: Fix -Wvoid-pointer-to-enum-cast warning
PCI: dwc: Add dw_pcie_ep_{read,write}_dbi[2] helpers
PCI: dwc: Rename .func_conf_select to .get_dbi_offset in struct dw_pcie_ep_ops
PCI: dwc: Rename .ep_init to .init in struct dw_pcie_ep_ops
PCI: dwc: Drop host prefix from struct dw_pcie_host_ops members
misc: pci_endpoint_test: Use a unique test pattern for each BAR
PCI: j721e: Make TI J721E depend on ARCH_K3
PCI: j721e: Add TI J784S4 PCIe configuration
PCI/AER: Use explicit register sizes for struct members
PCI/AER: Decode Requester ID when no error info found
PCI/AER: Use 'Correctable' and 'Uncorrectable' spec terms for errors
...
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, mpi3mr, mpt3sas, lpfc, fnic,
hisi_sas, arcmsr, ) plus the usual assorted minor fixes and updates.
This time around there's only a single line update to the core, so
nothing major and barely anything minor"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (135 commits)
scsi: ufs: core: Simplify ufshcd_auto_hibern8_update()
scsi: ufs: core: Rename ufshcd_auto_hibern8_enable() and make it static
scsi: ufs: qcom: Fix ESI vector mask
scsi: ufs: host: Fix kernel-doc warning
scsi: hisi_sas: Correct the number of global debugfs registers
scsi: hisi_sas: Rollback some operations if FLR failed
scsi: hisi_sas: Check before using pointer variables
scsi: hisi_sas: Replace with standard error code return value
scsi: hisi_sas: Set .phy_attached before notifing phyup event HISI_PHYE_PHY_UP_PM
scsi: ufs: core: Add sysfs node for UFS RTC update
scsi: ufs: core: Add UFS RTC support
scsi: ufs: core: Add ufshcd_is_ufs_dev_busy()
scsi: ufs: qcom: Remove unused definitions
scsi: ufs: qcom: Use ufshcd_rmwl() where applicable
scsi: ufs: qcom: Remove support for host controllers older than v2.0
scsi: ufs: qcom: Simplify ufs_qcom_{assert/deassert}_reset
scsi: ufs: qcom: Initialize cycles_in_1us variable in ufs_qcom_set_core_clk_ctrl()
scsi: ufs: qcom: Sort includes alphabetically
scsi: ufs: qcom: Remove unused ufs_qcom_hosts struct array
scsi: ufs: qcom: Use dev_err_probe() to simplify error handling of devm_gpiod_get_optional()
...
|
|
Pull block updates from Jens Axboe:
"Pretty quiet round this time around. This contains:
- NVMe updates via Keith:
- nvme fabrics spec updates (Guixin, Max)
- nvme target udpates (Guixin, Evan)
- nvme attribute refactoring (Daniel)
- nvme-fc numa fix (Keith)
- MD updates via Song:
- Fix/Cleanup RCU usage from conf->disks[i].rdev (Yu Kuai)
- Fix raid5 hang issue (Junxiao Bi)
- Add Yu Kuai as Reviewer of the md subsystem
- Remove deprecated flavors (Song Liu)
- raid1 read error check support (Li Nan)
- Better handle events off-by-1 case (Alex Lyakas)
- Efficiency improvements for passthrough (Kundan)
- Support for mapping integrity data directly (Keith)
- Zoned write fix (Damien)
- rnbd fixes (Kees, Santosh, Supriti)
- Default to a sane discard size granularity (Christoph)
- Make the default max transfer size naming less confusing
(Christoph)
- Remove support for deprecated host aware zoned model (Christoph)
- Misc fixes (me, Li, Matthew, Min, Ming, Randy, liyouhong, Daniel,
Bart, Christoph)"
* tag 'for-6.8/block-2024-01-08' of git://git.kernel.dk/linux: (78 commits)
block: Treat sequential write preferred zone type as invalid
block: remove disk_clear_zoned
sd: remove the !ZBC && blk_queue_is_zoned case in sd_read_block_characteristics
drivers/block/xen-blkback/common.h: Fix spelling typo in comment
blk-cgroup: fix rcu lockdep warning in blkg_lookup()
blk-cgroup: don't use removal safe list iterators
block: floor the discard granularity to the physical block size
mtd_blkdevs: use the default discard granularity
bcache: use the default discard granularity
zram: use the default discard granularity
null_blk: use the default discard granularity
nbd: use the default discard granularity
ubd: use the default discard granularity
block: default the discard granularity to sector size
bcache: discard_granularity should not be smaller than a sector
block: remove two comments in bio_split_discard
block: rename and document BLK_DEF_MAX_SECTORS
loop: don't abuse BLK_DEF_MAX_SECTORS
aoe: don't abuse BLK_DEF_MAX_SECTORS
null_blk: don't cap max_hw_sectors to BLK_DEF_MAX_SECTORS
...
|
|
Now that host-aware devices are always treated as conventional this case
can't happen.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20231228075141.362560-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Give BLK_DEF_MAX_SECTORS a _CAP postfix and document what it is used for.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231227092305.279567-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
disk_clear_zoned only needs to be called when a device reported zone
managed mode first and we clear it. Add a check so that disk_clear_zoned
isn't called on devices that were never zoned.
This avoids a fairly expensive queue freezing when revalidating
conventional devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231217165359.604246-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Only use disk_set_zoned to actually enable zoned device support.
For clearing it, call disk_clear_zoned, which is renamed from
disk_clear_zone_settings and now directly clears the zoned flag as
well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231217165359.604246-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When zones were first added the SCSI and ATA specs, two different
models were supported (in addition to the drive managed one that
is invisible to the host):
- host managed where non-conventional zones there is strict requirement
to write at the write pointer, or else an error is returned
- host aware where a write point is maintained if writes always happen
at it, otherwise it is left in an under-defined state and the
sequential write preferred zones behave like conventional zones
(probably very badly performing ones, though)
Not surprisingly this lukewarm model didn't prove to be very useful and
was finally removed from the ZBC and SBC specs (NVMe never implemented
it). Due to to the easily disappearing write pointer host software
could never rely on the write pointer to actually be useful for say
recovery.
Fortunately only a few HDD prototypes shipped using this model which
never made it to mass production. Drop the support before it is too
late. Note that any such host aware prototype HDD can still be used
with Linux as we'll now treat it as a conventional HDD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231217165359.604246-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In commit 8930a6c20791 ("scsi: core: add support for request batching") the
block layer bd->last flag was mapped to SCMD_LAST and used as an indicator
to send the batch for the drivers that implement this feature. However, the
error handling code was not updated accordingly.
scsi_send_eh_cmnd() is used to send error handling commands and request
sense. The problem is that request sense comes as a single command that
gets into the batch queue and times out. As a result the device goes
offline after several failed resets. This was observed on virtio_scsi
during a device resize operation.
[ 496.316946] sd 0:0:4:0: [sdd] tag#117 scsi_eh_0: requesting sense
[ 506.786356] sd 0:0:4:0: [sdd] tag#117 scsi_send_eh_cmnd timeleft: 0
[ 506.787981] sd 0:0:4:0: [sdd] tag#117 abort
To fix this always set SCMD_LAST flag in scsi_send_eh_cmnd() and
scsi_reset_ioctl().
Fixes: 8930a6c20791 ("scsi: core: add support for request batching")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Atanasov <alexander.atanasov@virtuozzo.com>
Link: https://lore.kernel.org/r/20231215121008.2881653-1-alexander.atanasov@virtuozzo.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
skb_share_check() already drops the reference to the skb when returning
NULL. Using kfree_skb() in the error handling path leads to an skb double
free.
Fix this by removing the variable tmp_skb, and return directly when
skb_share_check() returns NULL.
Fixes: 01a4cc4d0cd6 ("bnx2fc: do not add shared skbs to the fcoe_rx_list")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20221114110626.526643-1-weiyongjun@huaweicloud.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
chenxiang <chenxiang66@hisilicon.com> says:
This series contain some fixes and cleanups including:
- Set .phy_attached before notifying phyup event HISI_PHYEE_PHY_UP_PM;
- Use standard error code instead of hardcode;
- Check before using pointer variable;
- Rollback some operations if FLR failed;
- Correct the number of global debugfs registers;
Link: https://lore.kernel.org/r/1702525516-51258-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In function debugfs_debugfs_snapshot_global_reg_v3_hw() it uses
debugfs_axi_reg.count (which is the number of axi debugfs registers) to
acquire the number of global debugfs registers.
Use debugfs_global_reg.count to acquire the number of global debugfs
registers instead.
Fixes: 623a4b6d5c2a ("scsi: hisi_sas: Move debugfs code to v3 hw driver")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-6-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We obtain the semaphore and set HISI_SAS_RESETTING_BIT in
hisi_sas_reset_prepare_v3_hw(), block the scsi host and set
HISI_SAS_REJECT_CMD_BIT in hisi_sas_controller_reset_prepare(), released
them in hisi_sas_controller_reset_done(). However, if the HW reset failure
in FLR results in early return, the semaphore and flag bits will not be
release.
Rollback some operations including clearing flags / releasing semaphore
when FLR is failed.
Fixes: e5ea48014adc ("scsi: hisi_sas: Implement handlers of PCIe FLR for v3 hw")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-5-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In commit 4b329abc9180 ("scsi: hisi_sas: Move slot variable definition in
hisi_sas_abort_task()"), we move the variables slot to the function head.
However, the variable slot may be NULL, we should check it in each branch.
Fixes: 4b329abc9180 ("scsi: hisi_sas: Move slot variable definition in hisi_sas_abort_task()")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-4-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In function hisi_sas_controller_prereset(), -ENOSYS (Function not
implemented) should be returned if the driver does not support .soft_reset.
Returns -EPERM (Operation not permitted) if HISI_SAS_RESETTING_BIT is
already be set.
In function _suspend_v3_hw(), returns -EPERM (Operation not permitted) if
HISI_SAS_RESETTING_BIT is already be set.
Fixes: 4522204ab218 ("scsi: hisi_sas: tidy host controller reset function a bit")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
HISI_PHYE_PHY_UP_PM
Currently in directly attached scenario, the phyup event
HISI_PHYE_PHY_UP_PM is notified before .phy_attached is set - this may
cause the phyup work hisi_sas_bytes_dmaed() execution failed and the
attached device will not be found.
To fix it, set .phy_attached before notifing phyup event.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of copying @buf into a new buffer and carefully managing its
newline/null-terminating status, we can just use sysfs_match_string() as it
uses sysfs_streq() internally which handles newline/null-term:
| /**
| * sysfs_streq - return true if strings are equal, modulo trailing newline
| * @s1: one string
| * @s2: another string
| *
| * This routine returns true iff two strings are equal, treating both
| * NUL and newline-then-NUL as equivalent string terminations. It's
| * geared for use with sysfs input strings, which generally terminate
| * with newlines but are compared against values without newlines.
| */
| bool sysfs_streq(const char *s1, const char *s2)
| ...
Then entirely drop the now unused fcoe_parse_mode(), being careful to
change if condition from checking for FIP_CONN_TYPE_UNKNOWN to < 0 as
sysfs_match_string() can return -EINVAL. Also check explicitly if
ctlr->mode is equal to FIP_CONN_TYPE_UNKNOWN -- this is probably preferred
to "<=" as the behavior is more obvious while maintaining functionality.
To get the compiler not to complain, make fip_conn_type_names const char *
const. Perhaps, this should also be done for fcf_state_names.
This also removes an instance of strncpy() which helps [1].
Link: https://github.com/KSPP/linux/issues/90 [1]
Cc: <linux-hardening@vger.kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20231212-strncpy-drivers-scsi-fcoe-fcoe_sysfs-c-v2-1-1f2d6b2fc409@google.com
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Justin Tee <justintee8345@gmail.com> says:
Update lpfc to revision 14.2.0.17
This patch set contains bug fixes for the VMID feature.
The patches were cut against Martin's 6.8/scsi-queue tree.
Link: https://lore.kernel.org/r/20231207224039.35466-1-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update lpfc version to 14.2.0.17
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20231207224039.35466-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
completes
If priority tagging is set in the service parameters of a FLOGI cmpl, then
we update the vmid_flag. In the current logic, if a follow up FLOGI cmpl
updates its service parameters such that priority tagging is no longer set,
then the vmid_flag ends up keeping stale data.
Fix by ensuring we clear the vmid_flag member during lpfc_reinit_vmid, and
check the priority tagging service parameter after reinitialization of the
vmid data structures.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20231207224039.35466-4-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After a follow up FDISC cmpl, an NPIV's VMID data structures are not
updated.
Fix by calling lpfc_reinit_vmid and copying the physical port's vmid_flag
to the NPIV's vmid_flag in the NPIV registration cmpl code path.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20231207224039.35466-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
VMID driver support is a load time configuration setting. Thus, change
sysfs attributes to read only.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20231207224039.35466-2-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Karan Tilak Kumar <kartilak@cisco.com> says:
Hi Martin, reviewers,
This cover letter describes the feature: add support for
multiqueue (MQ) to fnic driver.
Background: The Virtual Interface Card (VIC) firmware exposes several
queues that can be configured for sending IOs and receiving IO
responses. Unified Computing System Manager (UCSM) and Intersight
Manager (IMM) allows users to configure the number of queues to be
used for IOs.
The number of IO queues to be used is stored in a configuration file
by the VIC firmware. The fNIC driver reads the configuration file and
sets the number of queues to be used. Previously, the driver was
hard-coded to use only one queue. With this set of changes, the fNIC
driver will configure itself to use multiple queues. This feature
takes advantage of the block multiqueue layer to parallelize IOs being
sent out of the VIC card.
Here's a brief description of some of the salient patches:
- vnic_scsi.h needs to be in sync with VIC firmware to be able to read
the number of queues from the firmware config file. A patch has been
created for this.
- In an environment with many fnics (like we see in our customer
environments), it is hard to distinguish which fnic is printing logs.
Therefore, an fnic number has been included in the logs.
- read the number of queues from the firmware config file.
- include definitions in fnic.h to support multiqueue.
- modify the interrupt service routines (ISRs) to read from the
correct registers. The numbers that are used here come from discussions
with the VIC firmware team.
- track IO statistics for different queues.
- remove usage of host_lock, and only use fnic_lock in the fnic driver.
- use a hardware queue based spinlock to protect io_req.
- replace the hard-coded zeroth queue with a hardware queue number.
This presents a bulk of the changes.
- modify the definition of fnic_queuecommand to accept multiqueue tags.
- improve log messages, and indicate fnic number and multiqueue tags for
effective debugging.
Even though the patches have been made into a series, some patches are
heavier than others.
But, every effort has been made to keep the purpose of each patch as
a single-purpose, and to compile cleanly.
This patchset has been tested as a whole. Therefore, the tested-by fields
have been added only to two patches
in the set. All the individual patches compile cleanly. However,
I've refrained from adding tested-by to
most of the patches, so as to not mislead the reviewer/reader.
A brief note on the unit tests:
1. Increase number of queues to 64. Load driver. Run IOs via Medusa.
12+ hour run successful.
2. Configure multipathing, and run link flaps on single link.
IOs drop briefly, but pick up as expected.
3. Configure multipathing, and run link flaps on two links, with a
30 second delay in between. IOs drop briefly, but pick up as expected.
Repeat the above tests with 1 queue and 32 queues. All tests were
successful.
Please consider this patch series for the next merge window.
Link: https://lore.kernel.org/r/20231211173617.932990-1-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Increment driver version for multiqueue (MQ).
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-14-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Improve existing logs by adding fnic number, hardware queue, tag, and mqtag
in the prints. Add logs with the above elements for effective debugging.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Tested-by: Karan Tilak Kumar <kartilak@cisco.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-13-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Implement support for MQ in fnic driver:
The block multiqueue layer issues IO to the fnic driver with an MQ tag. Use
the mqtag and derive a tag from it. Derive the hardware queue from the
mqtag and use it in all paths. Modify queuecommand to handle mqtag.
Replace wq and cq indices to support MQ. Replace the zeroth queue with a
hardware queue. Implement spin locks on a per hardware queue basis.
Replace io_lock with per hardware queue spinlock. Implement out of range
tag checks.
Allocate an io_req_table to track status of the io_req.
Test the driver by building it, loading it, and configuring 64 queues in
UCSM. Issue IOs using Medusa on multiple fnics. Enable/disable links to
exercise the abort and clean up path.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310300032.2awCqkfn-lkp@intel.com/
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Tested-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-12-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Set map_queues in the fnic_host_template to fnic_mq_map_queues_cpus.
Define fnic_mq_map_queues_cpus to set cpu assignment to fnic queues.
Refactor code in fnic_probe to enable vnic queues before scsi_add_host.
Modify notify set to the correct index.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-11-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove usage of host_lock. Replace with fnic_lock, where necessary. fnic
does not use host_lock. fnic uses fnic_lock. Use fnic lock to protect fnic
members in fnic_queuecommand. Add log messages in error cases.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-10-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Define an array to track IOs for the different queues, print the IO stats
in fnic get stats data.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-9-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Modify interrupt service routines for INTx, MSI, and MSI-x to support
multiqueue. Modify parameter list of fnic_wq_copy_cmpl_handler to take
cq_index. Modify fnic_cleanup function to use the new function call of
fnic_wq_copy_cmpl_handler. Refactor code to set interrupt mode to MSI-x to
a new function. Add a new stat for intx_dummy.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310251847.4T8BVZAZ-lkp@intel.com/
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-8-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Refactor and re-define values in fnic.h to implement multiqueue (MQ)
functionality.
VIC firmware allows fnic to create up to 64 copy workqueues. Update the
copy workqueue max to 64. Modify the interrupt index to be in sync with
the firmware to support MQ. Add irq number to the MSIX entry. Define a
software workqueue table to track the status of io_reqs. Define a base for
the copy workqueue.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-7-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Get the copy workqueue count and interrupt mode from the configuration. The
config can be changed via UCSM. Add logs to print the interrupt mode and
copy workqueue count. Add logs to print the vNIC resources.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-6-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rename wq_copy to hw_copy_wq to accurately describe the copy
workqueue. This will also help distinguish this data structure from
software data structures that can be introduced.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-5-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add link related log messages in fnic_fcs.c,
Improve log message in fnic_fcs.c,
Add log message in vnic_dev.c.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-4-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add fnic_num in fnic.h to identify fnic in a multi-fnic environment.
Increment and set the fnic number during driver load in fnic_probe.
Replace the host number with fnic number in debugfs.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-3-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
VIC firmware has updated definitions. Modify structure and definitions to
sync with the latest VIC firmware.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20231211173617.932990-2-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This reverts commit 9dc704dcc09eae7d21b5da0615eb2ed79278f63e.
Several reports have been made indicating that this commit caused
hangs. Numerous attempts at root causing and fixing the issue have
been unsuccessful so let's revert for now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217599
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The newly introduced error messages get multiple format strings wrong:
size_t must be printed using the %z modifier rather than %l and dma_addr_t
must be printed by reference using the special %pad pointer type:
drivers/scsi/mpi3mr/mpi3mr_app.c: In function 'mpi3mr_build_nvme_prp':
include/linux/kern_levels.h:5:25: error: format '%llx' expects argument of type 'long long unsigned int', but argument 4 has type 'dma_addr_t' {aka 'unsigned int'} [-Werror=format=]
drivers/scsi/mpi3mr/mpi3mr_app.c:949:25: note: in expansion of macro 'dprint_bsg_err'
949 | dprint_bsg_err(mrioc,
| ^~~~~~~~~~~~~~
include/linux/kern_levels.h:5:25: error: format '%ld' expects argument of type 'long int', but argument 4 has type 'size_t' {aka 'unsigned int'} [-Werror=format=]
drivers/scsi/mpi3mr/mpi3mr_app.c:1112:41: note: in expansion of macro 'dprint_bsg_err'
1112 | dprint_bsg_err(mrioc,
| ^~~~~~~~~~~~~~
Fixes: 9536af615dc9 ("scsi: mpi3mr: Support for preallocation of SGL BSG data buffers part-3")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231207142813.935717-1-arnd@kernel.org
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> says:
Hello,
this series converts all drivers below drivers/scsi to struct
platform_driver::remove_new(). See commit 5c5a7680e67b ("platform:
Provide a remove callback that returns no value") for an extended
explanation and the eventual goal.
All conversations are trivial, because all .remove() callbacks returned
zero unconditionally.
Best regards
Uwe
Link: https://lore.kernel.org/r/cover.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/1d385231c23c2a1e6e7dc1968eb111327386d1f6.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5010d1a4f3d77eaa1114fa254c343c4f23313901.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/84239a68fe06143d1d6fed6c9aaae6a4680ead71.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/2f4b7366ca00a107a9595514795e909e632980da.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/92114604fd1274073915e515cae15003ff07aa4a.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/8242c07f617fc946aab857c9357f540598fe964e.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/1d16e93a498831abd64df8b8cf54fd8872cdd1cd.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/89ce161dad52d99df07135531512ccecb7f25d14.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/9013c84059b8ccd6a5c8305aa35cfdfa314ba74c.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/f71efbe17973c97fd2a1e78f8d7fcf456644510b.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/63294479a4e745210c078859afa88904fa0b3be8.1701619134.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
