| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The initial-control-block references are not always correct
as the use-node-name qualifier during NVRAM configuration
will cause the firmware to use the portname as a base for
the nodename.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
From: FUJITA Tomonori <tomof@acm.org> and zhenyu.z.wang@intel.com:
We cannot handle filesystems like XFS becuase of the pages they
are sending us. We had thought page_count could be used to
work around this, but the correct test is for PageSlab.
The proper solution is to figure out what type of pages
filesystems can use so we do not have to add tests like
this or handle it in the block layer for all network block drivers
but the issue still has not been resolved on fs-devel
so we are sending this patch as a temporary fix.
This is last patch just in case it is Nakd with the explanation
that we need to push the correct fix through fs-devel, mm
or the block layer. The rest of the patchset can live without
the patch, but the driver will not work with filesystems like
XFS.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
When we run the xmit code from queuecomand the stack trace
gets too deep. The patch runs the xmit code from the scsi_host
work queue. This fixes 4k stack and xfs support and should
fix the st and sg stack usage bugs.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This is the second version of the patch to address Christoph's comments.
Instead of doing the lib, I just kept everything in scsi_trnapsort_iscsi.c
like the FC and SPI class. This was becuase the driver model and sysfs
class is tied to the session and connection setup so separating did not
buy very much at this time.
The reason for this patch was becuase HW iscsi LLDs like qla4xxx cannot
use the iscsi class becuase the scsi_host was tied to the interface and
class code. This patch just seperates the session from scsi host so
that LLDs that allocate the host per some resource like pci device
can still use the class.
This is also fixes a couple refcount bugs that can be triggered
when users have a sysfs file open, close the session, then
read or write to the file.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
From Mike Christie <michaelc@cs.wisc.edu> and FUJITA Tomonori <tomof@acm.org>:
We cannot use page_address becuase some pages could be highmem.
Instead, we can use sock_no_sendpage which does kmap for us.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Users can write to a page while we are sending it and making
digest calculations. This ends up causing us to retry the command
when a digest error is later reported. By using sock_no_sendpage
when data digests are calculated we can avoid a lot of (not all but it
helps) the retries becuase sock_no_sendpage is not zero copy.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
We should be taking the host_lock instead of the conn lock when
checking host_busy.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
We need to check the ISCSI_FLAG_DATA_* flags.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Remove extra whitespaces.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Convert a the 3w-9xxx.c and 3w-xxxx.c drivers to use mutexes instead
of semaphores. Untested, but compiles and looks obviously correct.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
We will be mapping the RAID volumes in mptsas to a reserved
channel that
is one larger than the anticapated number of ports on the direct
attached host
adapter.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
When James Smart fixed the issue of the userspace scan atributes
crashing the system with the FC transport class he added a patch to
let the transport class check if the parent is valid for a given
transport class.
When adding support for the integrated raid of fusion sas devices
we ran into a problem with that, as it didn't allow adding virtual
raid volumes without the transport class knowing about it.
So this patch adds a user_scan attribute instead, that takes over from
scsi_scan_host_selected if the transport class sets it and thus lets
the transport class control the user-initiated scanning. As this
plugs the hole about user-initiated scanning the target_parent hook
goes away and we rely on callers of the scanning routines to do
something sensible.
For SAS this meant I had to switch from a spinlock to a mutex to
synchronize the topology linked lists, in FC they were completely
unsynchronized which seems wrong.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Convert the SCSI transport class code to use a mutex rather than a
semaphore.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The problem in dpt_i2o could be the pci config space accesses it
triggers as it loads, dangerous to do if there is any I/O activity going
on in the other driver (probable if a boot driver I guess).
I approve this patch to dpt_i2o.c, and am applying it to the Adaptec
branch of the driver.
Thanks for the investigation Ryoji.
---
In linux 2.6.15, data transfer does hang when both dpt_i2o
and i2o_block drivers are loaded.
It seems that location of pci_request_regions() are wrong.
I moved it just behind pci_enable_device() like other drivers,
and it becomes fine.
Signed-off-by: Ryoji Kamei <kamei@miraclelinux.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
To avoid the "sda: got wrong page" message, the ServeRAID driver
should be setting flags indicating that the Mode Sense commands are
not supported.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Add fc_host attribute permanent_port_name which is
used to show the port name of the primary port -
the port that initially logged into the fabric.
For a virtual port (registered via the primary port with
FDISC command) it is useful to know not only its (virtual)
port name but also the permanent port name.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
split each ioctl handled in sr_audio_ioctl into a function of it's own.
This cleans the code up nicely, and allows various places in sr_ioctl
to call these helpers directly instead of going through the multiplexer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just
fine in the core code. There is a small behaviour change in that some
check in sr's rw_intr are bypassed, but I consider the old behaviour
a bug.
Mike found this cleanup opportunity and provdided early patches, so all
the credit goes to him, even if I redid the patches from scratch beause
that was easier than forward-porting the old patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
We need to iterate over all children when removing and expander, else
stale objects will be around after host removal. This fixes the oops
Eric Moore saw when removing and reloading mptsas.
Also don't try the scsi_remove_target call unless operating on an end
device. The current unconditional call is harmless but confusing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
While trying to get SUSE's SLES9 working on system with more than 4GB we've
noticed that SCSI layer happilly passes addresses over 4GB to the buslogic
driver, which is quite a big problem as buslogic can generate only 32bit
busmastering cycles.
Fortunately in the current kernels this problem does not exist anymore as
SCSI layer now assumes 4GB capable device by default, but it is still good
idea to pass correct device structure to the SCSI layer. If nothing else,
/sys/block/sda/device now points to
/sys/devices/pci0000:00/0000:00:10.0/host0/... instead of
/sys/devices/platform/host0/... like it did in the past.
Change does nothing for ISA based BusLogic adapters, they'll still end
under platform (and they are probably broken for long time as I do not see
anything forcing ISA 16MB limit for them).
Signed-off-by: Petr Vandrovec <petr@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This takes us past the old 1.x version of the SCSI driver and the 2.x
version of the aic website version to reflect the full incorporation
of both branches.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Update sequencer code to Adaptec version 2.0.12-6.3.9.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch coalesces inb/outb calls to the approriate word or long form.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Use struct map_node instead of separate variables.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
SCSI-1 CD drives can't do MRW or be opened for writing, so mask off
those capabilities.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received From Mark Salyzyn.
Move the README from the driver directory to the Documentation directory.
Updated the documentation, added descriptions for cards that
were missing.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received From Mark Salyzyn.
The Jaguar and Corsair class of adapters (2410, 2810, 2610, 21610, CERC)
perform better (about 10% better read performance, write performance
neutral) with current Firmware if the OS limits the number of scatter
gather elements to 17 per request.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn.
Provide more accurate adapter information.
Allows the Adapter Firmware to override the Adapter product
information.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn.
If the adapter has not instructed us otherwise that it can handle a
'large' FIB, then it can handle at most a 2KB FIB.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
We need to clear the backpointer on rphy removal, else we'll run into
problems with host removal after a device has been hot unplugged.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
the scsi layer is using semaphores in a mutex way, this patch converts
these into using mutexes instead
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The driver is doing a rather stupid mod_timer allegedly to "give
request sense more time to complete". This is illegal and pointless,
so just eliminate it. Also eliminate all the other uses of struct
timer_list in the driver, which are mostly bogus.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Original From: Adrian Bunk
Here's a composite patch with Adrian's original additions and
help-text with the new Kconfig variable SCSI_QLA_FC.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Adding defines for RAID10 and RAID50 levels, in preparation
of adding RAID Transport support in the mpt fusion drivers.
(BTW: IME is RAID10, and IM is RAID1).
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
These days ioctl32.h is only used for communication of fs/compat.c and
fs/compat_ioctl.c and doesn't contain anything of interest to drivers.
Remove inclusion in various drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
sg_page_malloc should clear the data buffer, not that extent of mem_map.
This fixes Jesper's sg_page_free "Bad page states"
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
|
|
This patch works around a problem with spurious interrupts seen at boot time when
a MAXTOR 6H500F0 drive is present. An ATA interrupt condition is mysteriously
present at start of day. If we took too long in issuing the first command,
the kernel would basically get tired of the spurious interrupts and turn the interrupt
off. Issuing the first command essentially causes the interrupt condition to
get acknowledged.
I haven't seen this happen with any other drives.
What I basically do is ack ATA status by reading it regardless of whether we're
expecting to have to handle an interrupt. This clears the start-of-day anomalous
interrupt condition, and keeps the kernel from disabling that interrupt due to
too many spurious interrupts.
Also, I fixed a bug where hotplug interrupts weren't getting acknowledged as handled
in the ISR. This was not the cause of the spurious interrupts, but it's the right
thing to do anyway.
Signed-Off-By: Andrew Chew
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
This patch moves the SCSI softirq handling to the block layer version.
There should be no functional changes.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
Many ARM drivers do not need to include asm/irq.h - remove this
unnecessary include from some ARM drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Manual fixup for merge with Jens' "Suspend support for libata", commit
ID 9b847548663ef1039dd49f0eb4463d001e596bc3.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
