| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The latest MegaRAID Firmware (for Invader series) has support for 64bit
DMA for both streaming and consistent DMA buffers. All Ventura series
controller FW always support 64 bit consistent DMA. Also, on a few
architectures 32bit DMA is not supported.
Current driver always prefers 32bit for consistent DMA and 64bit for
streaming DMA. This behavior was unintentional and carried forwarded
from legacy controller FW. Need to enhance the driver to support 64bit
consistent DMA buffers based on the firmware capability.
Below is the DMA setting strategy in driver with this patch. For
Ventura series, always try to set 64bit DMA mask. If it fails fall back
to 32bit DMA mask. For Invader series and earlier generation
controllers, first try to set to 32bit consistent DMA mask irrespective
of FW capability. This is needed to ensure firmware downgrades do not
break. If 32bit DMA setting fails, check FW capability and try seting to
64bit DMA mask.
There are certain restrictions in the hardware for having all sense
buffers and all reply descriptors to be in the same 4GB memory region.
This limitation is h/w dependent and can not be changed in firmware.
This limitation needs to be taken care in driver while allocating the
buffers. There was a discussion regarding this - find details at below
link. https://www.spinics.net/lists/linux-scsi/msg108251.html
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
cmd->frame->dcmd.opcode will be valid only for MFI_CMD_DCMD
IOCTL frames. Currently driver check for cmd->frame->dcmd.opcode without
checking cmd type. Ensure we check dcmd opcode only for MFI_CMD_DCMD
commands. Separate handling of MFI_CMD_SMP/STP commands from
MFI_CMD_DCMD in completion path.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Re-use the pre-allocated ctrl_info DMA buffer.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pre-allocate few of the frequently used DMA buffers during load time.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
fusion_context structure is very large around 180kB and most of the size
is contributed by log_to_span array. Move log_to_span out of fusion
context and have separate allocation for log_to_span. And use kmalloc to
allocate fusion_context. Currently kmemleak reports 1000s of false
positives for fusion->cmd_list[]. kmemleak does not track page
allocation for fusion_context. This change will also fix the false
positives reported by kmemleak.
Ref: https://marc.info/?l=linux-scsi&m=150545293900917
Reported-by: Shu Wang <shuwang@redhat.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
No functional change.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add support for PCI VID/DID 0x1000/0x0015 based MegaRAID controllers.
Since the DID 0x0015 conflicts with DELL PERC5 controllers,
add vendor ID based check specific for DELL PERC5.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
No functional change.
Refactor adapter_type to set for all generation controllers, not
just for fusion controllers.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
RAID map
Driver's local RAID map is accessed frequently. We will first try to get
memory from __get_free_pages. If this fails, fall back to using vmalloc.
For crash dump buffers always prefer vmalloc.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix indentation issues and smatch warning reported by Dan Carpenter
for previous series as discussed below.
http://www.spinics.net/lists/linux-scsi/msg103635.html
http://www.spinics.net/lists/linux-scsi/msg103603.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix - increase internal command pool to 8.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Memset the IO frame to zero after release.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
access
Change MR_TargetIdToLdGet return type from u8 to u16.
ld id range check is added at two places in this patch -
@megasas_build_ldio_fusion and @megasas_build_ld_nonrw_fusion. Previous
driver code used different data type for lds TargetId returned from
MR_TargetIdToLdGet. Prior to this change, above two functions was
safeguarded due to function always return u8 and maximum value of ld id
returned was 255.
In below check, fw_supported_vd_count as of today is 64 or 256 and valid
range to support is either 0-63 or 0-255. Ideally want to filter
accessing raid map for ld ids which are not valid. With the u16 change,
invalid ld id value is 0xFFFF and we will see kernel panic due to random
memory access in MR_LdRaidGet. The changes will ensure we do not call
MR_LdRaidGet if ld id is beyond size of ldSpanMap array.
if (ld < instance->fw_supported_vd_count)
>From firmware perspective,ld id 0xFF is invalid and even though current
driver code forward such command, firmware fails with target not
available.
ld target id issue occurs mainly whenever driver loops to populate raid
map (ea. MR_ValidateMapInfo). These are the only two places where we
may see out of range target ids and wants to protect raid map access
based on range provided by Firmware API.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
fails
Currently fusion context has fixed array load_balance_info. Use dynamic
allocation. In few places, driver do not want physically contigious
memory. Attempt to use vmalloc if physical contiguous memory is not
available.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add additional logging from driver in OCR context.
Add debug logs for partial completion of IOs is iodone context.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Avoid Host side PCI bandwidth bottleneck and hint FW to do Write
buffering using RaidFlag MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT. Once
IO is landed in FW with MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT, it will
do single DMA from host and buffer the Write operation. On back end, FW
will DMA same buffer to the Mirror and Data Arm. This will improve
large block IO performance which bottleneck due to Host side PCI
bandwidth limitation.
Consistent ~4000MB T.P for 256K Block size is expected performance
numbers. IOPS for small Block size should be on par with Disk
performance. (E.g 42 SAS Disk in JBOD mode gives 3700MB T.P. Same
Drive used in R1 WT mode, should give ~1800MB T.P)
Using this patch 24 R1 VDs (HDD) gives below performance for Sequential
Write. Without this patch, we cannot reach above 3200MB (Throughput is
in MB.)
Block Size 50% 256K and 50% 4K 100% 256K
4K 3100 2030
8K 3140 2740
16K 3140 3140
32K 3400 3240
64K 3500 3700
128K 3870 3870
256K 3920 3920
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch provide true fast path IO support. Driver creates PRP for
NVME drives and send Fast Path for performance. Certain h/w requirement
needs to be taken care in driver.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fetch true values of NVME property from FW using New DCMD
interface MR_DCMD_DEV_GET_TARGET_PROP
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Adding detection logic for NVME device attached behind Ventura
controller. Driver set HostPageSize in IOC_INIT frame to inform about
page size for NVME devices. Firmware reports NVME page size to the
driver. PD INFO DCMD provide new interface type NVME_PD. Driver set
property of NVME device.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
With the changes to remove checks for a valid request descriptor,
issue_dcmd will now always return DCMD_SUCCESS. This patch changes
return type of issue_dcmd to void and change all callers appropriately.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Threshold Bandwidth"
This reverts commit "3e5eadb1a881" ("scsi: megaraid_sas: Enable or
Disable Fast path based on the PCI Threshold Bandwidth")
This patch was aimed to increase performance of R1 Write operation for
large IO size. Since this method used timer approach, it turn on/off
fast path did not work as expected. Patch 0013 describes new algorithm
and performance number.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Upgrade driver version.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Controllers
Update Linux driver to use new pdTargetId field for JBOD target ID
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Bandwidth
Large SEQ IO workload should sent as non fast path commands
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Controllers
SAS3.5 Generic Megaraid Controllers FW will support new dynamic RaidMap to have different
sizes for different number of supported VDs.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
1/10 Writes
To improve RAID 1/10 Write performance, OS drivers need to issue the
required Write IOs as Fast Path IOs (after the appropriate checks
allowing Fast Path to be used) to the appropriate physical drives
(translated from the OS logical IO) and wait for all Write IOs to complete.
Design: A write IO on RAID volume will be examined if it can be sent in
Fast Path based on IO size and starting LBA and ending LBA falling on to
a Physical Drive boundary. If the underlying RAID volume is a RAID 1/10,
driver issues two fast path write IOs one for each corresponding physical
drive after computing the corresponding start LBA for each physical drive.
Both write IOs will have the same payload and are posted to HW such that
replies land in the same reply queue.
If there are no resources available for sending two IOs, driver will send
the original IO from SCSI layer to RAID volume through the Firmware.
Based on PCI bandwidth and write payload, every second this feature is
enabled/disabled.
When both IOs are completed by HW, the resources will be released
and SCSI IO completion handler will be called.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
IO Coalescing
Detect sequential Write IOs and pass the hint that it is part of sequential
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this will help driver to
send it to Firmware even if the IOs can potentially be sent to
hardware directly (called fast path) bypassing firmware.
Design: 8 streams are maintained per RAID volume as per the combined
firmware/driver design. When there is no stream detected the LRU stream
is used for next potential stream and LRU/MRU map is updated to make this
as MRU stream. Every time a stream is detected the MRU map
is updated to make the current stream as MRU stream.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SAS3.5 Generic Megaraid based Controllers will have the support for 128 MSI-X vectors,
resulting in the need to support 128 reply queues
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Controllers
This patch contains new pci device ids for SAS3.5 Generic Megaraid Controllers
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
|
|
[mkp: fixed bad indentation]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch will fix regression caused by commit 1e793f6fc0db ("scsi:
megaraid_sas: Fix data integrity failure for JBOD (passthrough)
devices").
The problem was that the MEGASAS_IS_LOGICAL macro did not have braces
and as a result the driver ended up exposing a lot of non-existing SCSI
devices (all SCSI commands to channels 1,2,3 were returned as
SUCCESS-DID_OK by driver).
[mkp: clarified patch description]
Fixes: 1e793f6fc0db920400574211c48f9157a37e3945
Reported-by: Jens Axboe <axboe@kernel.dk>
CC: stable@vger.kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Tested-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Tested-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Until now the megaraid_sas driver has reported successful completion on
SYNCHRONIZE_CACHE commands without sending them down to the controller.
The controller firmware has been responsible for taking care of flushing
disk caches for all drives that belong to a Virtual Disk at the time of
system reboot/shutdown.
There may have been a reason to avoid sending SYNCHRONIZE_CACHE to a VD
in the past but that no longer appears to be valid.
Older versions of MegaRaid firmware (Gen2 and Gen2.5) set the WCE bit
for Virtual Disks but the firmware does not report correct completion
status for a SYNCHRONIZE_CACHE command. As a result, we must use another
method to identify whether it is safe to send the command to the
controller. We use the canHandleSyncCache firmware flag in the scratch
pad register at offset 0xB4.
New SYNCHRONIZE_CACHE behavior:
IF 'JBOD'
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware sends SYNCHRONIZE_CACHE to drive
Firmware obtains status from drive and returns same status back to driver
ELSEIF 'VirtualDisk'
IF firmware supports new API bit called canHandleSyncCache
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware does not send SYNCHRONIZE_CACHE to drives
Firmware returns SUCCESS
ELSE
Driver does not send SYNCHRONIZE_CACHE command to the firmware
Driver return SUCCESS for that command
ENDIF
ENDIF
[mkp: edited patch description]
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch will reduce memory footprints of megaraid_sas driver when
booted in kdump mode. Driver will not allocate memory for optional and
perfromance oriented features. Below are key changes done in
megaraid_sas driver to do this:
1. Limit Controller's queue depth to 100 in kdump mode.
2. Do not allocate memory for system info buffer and PD info buffer.
3. Disable performance oriented features e.g. Disable RDPQ mode, disable
dual queue depth, restrict to single MSI-x vector.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
list DCMD failure
There are few MFI adapters which do not support MR_DCMD_PD_LIST_QUERY so
if MFI adapters fail this DCMD, it should not be considered as FATAL and
driver should not issue kill adapter and set per controller's instance
variable- pd_list_not_supported so that same variable can be used inside
functions- slave_alloc and slave_configure to allow firmware scan.
Killing adapter because of DCMD failure when this DCMD is not supported
causes driver's probe getting failed. This issue got introduced by
commit 6d40afbc7d13 ("megaraid_sas: MFI IO timeout handling").
Killing adapter in case of this DCMD failure should be limited to Fusion
adapters only. Per controller's instance variable allow_fw_scan is
removed as pd_list_not_supported better reflect the purpose.
Fixes: 6d40afbc7d13359b30a5cd783e3db6ebefa5f40a
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Driver assumes that VFs always have peers present whenever they have
same LD IDs. But this is not the case. This patch handles the above
mentioned by explicitly checking for a peer before making HA/non-HA path
decision.
Signed-off-by: Uday Lingala <uday.lingala@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Make instance->adprecovery variable atomic and removes hba_lock spinlock
while accessing instance->adprecovery.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch will add capability in driver to tell firmware that it can
throttle IOs in case controller's queue depth is downgraded post OFU
(online firmware upgrade). This feature will ensure firmware can be
downgraded from higher queue depth to lower queue depth without needing
system reboot. Added throttling code in IO path of driver, in case OS
tries to send more IOs than post OFU firmware's queue depth.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
1. For iMR controllers, firmware will report two queue depths:
- Controller-wide queue depth
- LDIO queue depth (240)
Controller-wide queue depth will be greater among the two. Using this
new feature, iMR can provide larger Queue depth(QD) for JBOD and limited
QD for Virtual Disk(VD).
2. megaraid_sas driver will throttle read/write LDIOs based on "LDIO
Queue Depth".
3. Dual queue depth can be enabled/disabled via module parameter. It is
enabled by default if the firmware supports it. Only specific firmware
builds will enable the feature.
4. Added sysfs parameter "ldio_outstanding" which permits querying the
number of outstanding LDIO requests at runtime.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch will create a reply queue pool for each MSI-X index and will
provide an array of base addresses instead of the single address of
legacy mode. Using this new interface the driver can support higher
queue depths through scattered DMA pools.
If array mode is not supported driver will fall back to the legacy
method of reply pool allocation. This limits controller queue depth to
1K max. To enable a queue depth of more than 1K driver requires firmware
to support array mode and scratch_pad3 will provide the new queue depth
value.
When RDPQ is used, downgrading to an older firmware release should not
be permitted. This may cause firmware fault and is not supported.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Firmware will fill out per-LD data to tell driver whether a particular
LD supports region lock bypass. If yes, then driver will send non-FP
LDIO to region lock bypass FIFO. With this change in driver, firmware
will optimize certain code to improve performance.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
