| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is an SoC bug of v3 hw development version. When hot- unplugging a
directly attached disk, the PHY down interrupt may not happen. It is
very easy to appear on some boards.
When this issue occurs, the controller will receive many invalid dword
frames, and the "alos" fields of register HILINK_ERR_DFX can indicate
that disk was unplugged.
As an workaround solution, this patch detects this issue in the channel
interrupt, and workaround it by following steps:
- Disable the PHY
- Clear error code and interrupt
- Enable the PHY
Then the HW will reissue PHY down interrupt.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is common to use readl poll timeout helpers in the driver, so create
custom wrappers.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Event95 is used for DFX purpose. The relevant bit for this interrupt in
the ENT_INT_SRC_MSK3 register has been disabled, so remove the
processing.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As a unconstrained command, a command can be sent to SATA disk even if
SATA disk status is BUSY, ERR or DRQ.
If an ATA reset assert is successful but ATA reset de-assert fails, then
it will retry the reset de-assert. If reset de- assert retry is
successful, we think it is okay to probe the device but actually it
still has Err status.
Apparently we need to retry the ATA reset assertion and de- assertion
instead for this mentioned scenario.
As such, we config ATA reset assert as a constrained command, if ATA
reset de-assert fails, then ATA reset de-assert retry will also
fail. Then we will retry the proper process of ATA reset assert and
de-assert again.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After the controller is reset, we currently may not honour the PHY max
linkrate set via sysfs, in that after a reset we always revert to max
linkrate of 12Gbps, ignoring the value set via sysfs.
This patch modifies to policy to set the programmed PHY linkrate,
honouring the max linkrate programmed via sysfs.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We should only have the timer enabled after PHY up after controller
reset, so disable prior to reset.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is possible to dereference a NULL-pointer in hisi_sas_abort_task() in
special scenario when the device has been removed.
If an SMP task times-out, it will call hisi_sas_abort_task() to
recover. And currently there is a check in hisi_sas_abort_task() to
avoid the situation of processing the abort for the removed device.
However we have an ordering problem, in that we may reference a task for
the removed device before checking if the device has been removed.
Fix this by only referencing the sas_dev after we know it is still
present.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There are 28 bytes of protection information record of SSP for v3 hw, 16
bytes for v2 hw, and probably 24 for v1 hw (forgotten now).
So use a value big enough in hisi_sas_command_table_ssp.prot to cover
all cases.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the host is frozen in SCSI EH state, at any point after the LLDD
sets SAS_TASK_STATE_DONE for the sas_task task state, libsas may free
the task; see sas_scsi_find_task().
This puts the LLDD in a difficult position, in that once it sets
SAS_TASK_STATE_DONE for the task state it should not reference the
sas_task again. But the LLDD needs will check the sas_task indirectly in
calling task->task_done()->sas_scsi_task_done() or sas_ata_task_done()
(to check if the host is frozen state actually).
And the LLDD cannot set SAS_TASK_STATE_DONE for the task state after
task->task_done() is called (as the sas_task is free'd at this point).
This situation would seem to be a problem made by libsas.
To work around, check in the LLDD whether the host is in frozen state to
ensure it is ok to call task->task_done() function. If in the frozen
state, we rely on SCSI EH and libsas to free the sas_task directly.
We do not do this for the following IO types:
- SMP - they are managed in libsas directly, outside SCSI EH
- Any internally originated IO, for similar reason
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If the SCSI host enters EH, any pending IO will be processed by SCSI
EH. However it is possible that SCSI EH will try to abort the IO and
also at the same time the IO completes in the driver. In this situation
there is a small chance of freeing the sas_task twice.
Then if another IO re-uses freed sas_task before the second time of
free'ing sas_task, it is possible to free incorrect sas_task.
To avoid this situation, add some checks to increase reliability. The
sas_task task state flag SAS_TASK_STATE_ABORTED is used to mutually
protect the LLDD and libsas freeing the task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In the DQ tasklet processing it is not necessary to take the DQ lock, as
there is no contention between adding slots to the CQ and removing slots
from the matching DQ.
In addition, since we run each DQ in a separate tasklet context, there
would be no possible contention between DQ processing running for the
same queue in parallel.
It is still necessary to take hisi_hba lock when free'ing slots.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch removes unneeded structure elements:
- hisi_sas_phy.dev_sas_addr: only ever written
- Also remove associated function which writes it,
hisi_sas_init_add().
- hisi_sas_device.attached_phy: only ever written
- Also remove code to set it in hisi_sas_dev_found()
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When we find an erroneous slot completion, to help aid debugging add the
device index to the current debug log.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is a bug of v3 hw development version. When AXI error happen, hw
may return an abnormal CQ that IPTT value is 0xffff. This will cause
IPTT out-of-bounds reference.
This patch adds a check of IPTT in cq_tasklet_v3_hw() and discards
invalid slot. This workaround scheme is just to enhance fault-tolerance
of the driver. So, we will apply this scheme for all version of v3 hw,
although release version has fixed this SoC bug.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently we check the fis->command value in 2 locations in
hisi_sas_get_ata_protocol() switch statement. Fix this by consolidating
the check for fis->command value to 1 location only.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This is a warning coming from Coccinelle, and need to use new interface
dma_zalloc_coherent() instead of dma_alloc_coherent()/memset().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Delete timer for v1 and v3 hw when removing hisi_sas driver.
Signed-off-by: Xiang chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is an modification for later revision of v3 hw. More HW errors are
reported through RAS interrupt. These errors were originally reported
only through MSI.
When report to RAS, some combinations are done to port AXI errors and
FIFO OMIT errors. For example, each port has 4 AXI errors, and they are
combined to one when report to RAS.
This patch does two things:
1. Enable RAS interrupt of these errors and handle them in PCI
error handlers.
2. Disable MSI interrupts of these errors for this later revision hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When directly connected with SATA disks in different SAS cores, fill SAS
address with scsi_host's id to make it's fake SAS address unique.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST". In
most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Export device table of v3 hw to userspace, or auto probe will fail for v3
hw.
Also change the module alias to include "pci", instead of "platform".
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Do some modifications for register configuring for hip08.
In future, to reduce kernel churn with patches to modify registers, any
registers which may change between board models (mostly PHY/SERDES related)
should be set in ACPI reset handler.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The patch does some code cleanup and fixes some small bugs:
- Correct return status of phy_up_v3_hw() and phy_bcast_v3_hw()
- Add static for function phy_get_max_linkrate_v3_hw()
- Change exception return status when no reset method
- Change magic value to ts->stat in slot_complete_vx_hw()
- Remove unnecessary check for dev_is_sata()
- Fix some issues of alignment and indents (Authored by Xiaofei Tan in
another patch, but added here to be practical)
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is an implicit regulation that error code that function returned should
be negative. But hisi_sas_task_prep() doesn't follow this. This may cause
problems in the upper layer code.
For example, in sas_expander.c of libsas, smp_execute_task_sg() may return
the number of bytes of underrun. It will be conflicted with the scenaio
lldd_execute_task() return an positive error code.
This patch change the return value from SAS_PHY_DOWN to -ECOMM in
hisi_sas_task_prep().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The structure element hisi_sas_devices.running_req to count how many
commands are active is in effect only ever written in the code, so remove
it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The current 110ms expiry time is not long enough for the internal abort
task.
The reason is that the internal abort task could be blocked in HW if the HW
is retrying to set up link. The internal abort task will be executed only
when the retry process finished.
The maximum time is 5s for the retry of setting up link. So, the timer
expire should be more than 5s. This patch increases it from 110ms to 6s.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is not right to set the register PROG_PHY_LINK_RATE while PHY is still
enabled. So if we want to change PHY linkrate, we need to disable PHY before
setting the register PROG_PHY_LINK_RATE, and then start-up PHY. This patch
is to fix this issue.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In sysfs, there are two files about minimum linkrate, and also two files for
maximum linkrate. Take maximum linkrate example, maximum_linkrate_hw is
read-only and indicated by the register HARD_PHY_LINKRATE, and
maximum_linkrate is read-write and corresponding to the register
PROG_PHY_LINK_RATE.
But in the function phy_up_v*_hw(), we get *_linkrate value from
HARD_PHY_LINKRATE. It is not right. This patch is to fix this issue.
Unreferenced PHY-interrupt enum is also removed for v3 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The register SAS_PHY_CTRL is configured according to signal quality. The
signal quality is calculated by signal attenuation of hardware physical
link. It may be different for different PCB layout.
So, in order to give better support to new board, this patch add support to
reading the devicetree property, "hisilicon,signal-attenuation". Of course,
we still keep an default value in driver to adapt old board.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When device gone, NULL pointer can be accessed in free_device callback
if during SAS controller reset as we clear structure sas_dev prior.
Actually we can only set dev_type as SAS_PHY_UNUSED and not clear
structure sas_dev as all the members of structure sas_dev will be
re-initialized after device found.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch implements LED feature of directly attached disk for v2 hw.
As libsas has provided an interface lldd_write_gpio() for this feature,
we just need realise the interface following SPGIO API.
We use an CPLD to finish the hardware part of this feature, and the base
address of CPLD should be configured through ACPI or DT tables.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fixes the following sparse warning:
drivers/scsi/hisi_sas/hisi_sas_main.c:1691:25: warning:
symbol 'host_attrs' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
According to ATA protocol, SET MAX commands belong to different frame
types. So judge features field of SET MAX commands to decide which
frame type they belongs to.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a sysfs attr that LLDD can configure it for every host. We made an
example in hisi_sas. Other LLDDs using libsas can implement it if they
want.
Suggested-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
Acked-by: John Garry <john.garry@huawei.com> #for hisi_sas part
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For v3 hw SAS, it supports configuring power state from D0 to D3 for entering
Low Power status and power state from D3 to D0 for quit Low Power status.
When power state from D0 to D3, HW will send FLR to clear the registers of
ECAM and BAR space, and when power state from D3 to D0, it will clear the
registers of ECAM space only.
So when suspend, need to do like controller reset (including disable
interrupts/DQ/PHY/BUS), and also release slots after FLR. When resume,
re-config the registers of BAR space.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In function sas_suspend_devices(), it requires callback lldd_port_deformed
callback to be implemented if lldd_port_deformed is implemented.
So add a stub for lldd_port_deformed.
Callback lldd_port_deformed was not required as the port deformation is done
elsewhere in the LLDD.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fix SAS_QUEUE_FULL problem. The test situation is close port while
running IO.
In sas_eh_handle_sas_errors(), SCSI EH will free sas_task of the device if
lldd_I_T_nexus_reset() return TMF_RESP_FUNC_COMPLETE or -ENODEV. But in our
SAS driver, we only free slots of the device when the return value is
TMF_RESP_FUNC_COMPLETE. So if the return value is -ENODEV, the slot resource
will not free any more.
As an solution, we should also free slots of the device in
lldd_I_T_nexus_reset() if the return value is -ENODEV.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We should do internal abort dev before TMF_ABORT_TASK_SET and TMF_LU_RESET.
Because we may only have done internal abort for single IO in the earlier part
of SCSI EH process. Even the internal abort to the single IO, we also don't
know whether it is successful.
Besides, we should release slots of the device in hisi_sas_abort_task_set() if
the abort is successful.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Normally, hardware should ensure that internal abort timeout will never
happen. If happen, it would be an SoC failure. What's more, HW will not
process any other commands if an internal abort hasn't return CQ, and they
will time out also.
So, we should judge the result of internal abort in SCSI EH, if it is failed,
we should give up to do TMF/softreset and return failure to the upper layer
directly.
This patch do following things to achieve this:
1. When internal abort timeout happened, we set return value to -EIO in
hisi_sas_internal_task_abort().
2. If prep_abort() is not support, let hisi_sas_internal_task_abort() return
TMF_RESP_FUNC_FAILED.
3. If hisi_sas_internal_task_abort() return an negative number, it can be
thought that it not executed properly or internal abort timeout. Then we
won't do behind TMF or softreset, and return failure directly.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We should do link reset of PHY when identify timeout or STP link timeout. They
are internal events of SOC and are notified to driver through interrupts of
CHL_INT2.
Besides, we should add an delay work to do link reset as it needs sleep. So,
this patch add an new PHY event HISI_PHYE_LINK_RESET for this.
Notes: v2 HW doesn't report the event of STP link timeout. So, we only need
to handle event of identify timeout for v2 HW.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use an general way to do delay work for a PHY. Then it will be easier to add
new delayed work for a PHY in future.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add port AXI errors handling for v2 hw. We do host controller reset for such
errors.
Besides, change port muli-bits ECC error handling, and we should also do host
reset for such error. So, this patch put them in the same struct with port AXI
error.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change code format of int_chnl_int_v2_hw() to be consistent with v3 hw to
reduce an tag indent.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add some print at some places such as error info and cq of exception IO,
device found etc, and also adjust some log levels.
All this to assist debugging ability.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We use PCIe AER to support RAS feature for v3 hw. This driver should do
following two things to support this:
1. Enable RAS interrupts, so that errors can be reported to RAS module.
2. Realize err_handler for sas_v3_pci_driver. Then if non-fatal error is
detected, print error source and try to recover SAS controller.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For v3 hw, each NCQ will return a CQ, so it is no need to acquire IPTT from
ITCT, just acquire it from IPTT field of CQ.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Sometimes it is required to know when the controller reset has completed and
also if it has completed successfully. For such places, we call
hisi_sas_controller_reset() directly before. That may lead to multiple calls
to this function.
This patch create a per-reset structure which contains a completion structure
and status flag to know when the reset completes and also the status. It is
also in hisi_hba.wq to do reset work.
As all host reset works are done in hisi_hba.wq, we don't worry multiple calls
to hisi_sas_controller_reset().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Do a couple of changes for when HISI_SAS_RESET_BIT is set for HBA:
- Clearing ITCT is not necessary
- Remove internal abort as it will fail during reset
Flag sas_dev->dev_type is kept as SAS_PHY_UNUSED.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch do following optimizations to host controller reset:
1. Unblock scsi requests before rescanning topology, as SCSI command need be
used if new device is found during rescanning topology.
2. Remove drain_workqueue(hisi_hba->wq) and drain_workqueue(shost->work_q), as
there is no need to ensure that all PHYs event are done before exiting host
reset.
3. Improve message print level of host reset. Host reset is an important and
very few occurrence event. We should know its progress even when not
debugging.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently refreshing the PHY port id after reset is done in the rescan
topology function, which is quite late in the reset process. It could be moved
earlier in the process, as the port id can be refreshed once the PHYs become
ready.
In addition to this, we should set the hisi_sas_dev port id to 0xff (invalid
port id) if all PHYs of this port remain down for the same device.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
