summaryrefslogtreecommitdiff
path: root/drivers/scsi/dmx3191d.c
AgeCommit message (Collapse)AuthorFilesLines
2016-01-07ncr5380: Fix soft lockupsFinn Thain1-0/+1
Because of the rudimentary design of the chip, it is necessary to poll the SCSI bus signals during PIO and this tends to hog the CPU. The driver will accept new commands while others execute, and this causes a soft lockup because the workqueue item will not terminate until the issue queue is emptied. When exercising dmx3191d using sequential IO from dd, the driver is sent 512 KiB WRITE commands and 128 KiB READs. For a PIO transfer, the rate is is only about 300 KiB/s, so these are long-running commands. And although PDMA may run at several MiB/s, interrupts are disabled for the duration of the transfer. Fix the unresponsiveness and soft lockup issues by calling cond_resched() after each command is completed and by limiting max_sectors for drivers that don't implement real DMA. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-07ncr5380: Use standard list data structureFinn Thain1-0/+1
The NCR5380 drivers have a home-spun linked list implementation for scsi_cmnd structs that uses cmd->host_scribble as a 'next' pointer. Adopt the standard list_head data structure and list operations instead. Remove the eh_abort_handler rather than convert it. Doing the conversion would only be churn because the existing EH handlers don't work and get replaced in a subsequent patch. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-07ncr5380: Remove redundant ICR_ARBITRATION_LOST test and eliminate FLAG_DTC3181EFinn Thain1-1/+1
Remove FLAG_DTC3181E. It was used to suppress a final Arbitration Lost (SEL asserted) test that isn't actually needed. The test was suppressed because it causes problems for DTC436 and DTC536 chips. It takes place after the host wins arbitration, so SEL has been asserted. These chips can't seem to tell whether it was the host or another bus device that did so. This questionable final test appears in a flow chart in an early NCR5380 datasheet. It was removed from later documents like the DP5380 datasheet. By the time this final test takes place, the driver has already tested the Arbitration Lost bit several times. The first test happens 3 us after BUS FREE (or longer due to register access delays). The protocol requires that a device stop signalling within 1.8 us after BUS FREE unless it won arbitration, in which case it must assert SEL, which is detected 1.2 us later by the first Arbitration Lost test. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-07ncr5380: Fix and cleanup scsi_host_template initializersFinn Thain1-0/+1
Add missing .module initializer. Use distinct .proc_name values for the g_NCR5380 and g_NCR5380_mmio modules. Remove pointless CAN_QUEUE and CMD_PER_LUN override macros. Cleanup whitespace and code style. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-07ncr5380: Cleanup #include directivesFinn Thain1-5/+0
Remove unused includes (stat.h, signal.h, proc_fs.h) and move includes needed by the core drivers into the common header (delay.h etc). Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-07ncr5380: Introduce unbound workqueueFinn Thain1-6/+11
Allocate a work queue that will permit busy waiting and sleeping. This means NCR5380_init() can potentially fail, so add this error path. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-07ncr5380: Split NCR5380_init() into two functionsFinn Thain1-0/+2
This patch splits the NCR5380_init() function into two parts, similar to the scheme used with atari_NCR5380.c. This avoids two problems. Firstly, NCR5380_init() may perform a bus reset, which would cause the chip to assert IRQ. The chip is unable to mask its bus reset interrupt. Drivers can't call request_irq() before calling NCR5380_init(), because initialization must happen before the interrupt handler executes. If driver initialization causes an interrupt it may be problematic on some platforms. To avoid that, first move the bus reset code into NCR5380_maybe_reset_bus(). Secondly, NCR5380_init() contains some board-specific interrupt setup code for the NCR53C400 that does not belong in the core driver. In moving this code, better not re-order interrupt initialization and bus reset. Again, the solution is to move the bus reset code into NCR5380_maybe_reset_bus(). Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-07ncr5380: Remove NCR5380_local_declare and NCR5380_setup macrosFinn Thain1-4/+2
The NCR5380_local_declare and NCR5380_setup macros exist to define and initialize a particular local variable, to provide the address of the chip registers needed for the driver's implementation of its NCR5380_read/write register access macros. In cumana_1 and macscsi, these macros generate pointless code like this, struct Scsi_Host *_instance; _instance = instance; In pas16, the use of NCR5380_read/write in pas16_hw_detect() requires that the io_port local variable has been defined and initialized, but the NCR5380_local_declare and NCR5380_setup macros can't be used for that purpose because the Scsi_Host struct has not yet been instantiated. Moreover, these macros were removed from atari_NCR5380.c long ago and now they constitute yet another discrepancy between the two core driver forks. Remove these "optimizations". Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2014-11-20dmx3191d: Use NO_IRQFinn Thain1-17/+8
Testing shows that the Domex 3191D card never asserts its IRQ. Hence it is non-functional with Linux (worse, the EH bugs in the core driver are fatal but that's a problem for another patch). Perhaps the DT-536 chip needs special setup? I can't find documentation for it. The NetBSD driver uses polling apparently because of this issue. Set host->irq = NO_IRQ so the core driver will prevent targets from disconnecting. Don't request host->irq. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Drop legacy scsi.h includeFinn Thain1-1/+0
Convert Scsi_Cmnd to struct scsi_cmnd and drop the #include "scsi.h". The sun3_NCR5380.c core driver already uses struct scsi_cmnd so converting the other core drivers reduces the diff which makes them easier to unify. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Cleanup host info() methodsFinn Thain1-0/+1
If the host->info() method is not set, then host->name is used by default. For atari_scsi, that is exactly the same text. So remove the redundant info() method. Keep sun3_scsi.c in line with atari_scsi. Some NCR5380 drivers return an empty string from the info() method (arm/cumana_1.c arm/oak.c mac_scsi.c) while other drivers use the default (dmx3191d dtc.c g_NCR5380.c pas16.c t128.c). Implement a common info() method to replace a lot of duplicated code which the various drivers use to announce the same information. This replaces most of the (deprecated) show_info() output and all of the NCR5380_print_info() output. This also eliminates a bunch of code in g_NCR5380 which just duplicates functionality in the core driver. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Fix SCSI_IRQ_NONE bugsFinn Thain1-3/+4
Oak scsi doesn't use any IRQ, but it sets irq = IRQ_NONE rather than SCSI_IRQ_NONE. Problem is, the core NCR5380 driver expects SCSI_IRQ_NONE if it is to issue IDENTIFY commands that prevent target disconnection. And, as Geert points out, IRQ_NONE is part of enum irqreturn. Other drivers, when they can't get an IRQ or can't use one, will set host->irq = SCSI_IRQ_NONE (that is, 255). But when they exit they will attempt to free IRQ 255 which was never requested. Fix these bugs by using NO_IRQ in place of SCSI_IRQ_NONE and IRQ_NONE. That means IRQ 0 is no longer probed by ISA drivers but I don't think this matters. Setting IRQ = 255 for these ISA drivers is understood to mean no IRQ. This remains supported so as to avoid breaking existing ISA setups (which can be difficult to get working) and because existing documentation (SANE, TLDP etc) describes this usage for the ISA NCR5380 driver options. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Remove redundant AUTOSENSE macroFinn Thain1-1/+0
Every NCR5380 driver sets AUTOSENSE so it need not be optional (and the mid-layer expects it). Remove this redundant macro to improve readability. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Remove unused hostdata fieldsFinn Thain1-2/+2
Remove unused fields from hostdata structs declared with the NCR5380_implementation_fields macro. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2013-01-04Drivers: scsi: remove __dev* attributes.Greg Kroah-Hartman1-4/+4
CONFIG_HOTPLUG is going away as an option. As a result, the __dev* markings need to be removed. This change removes the use of __devinit, __devexit_p, __devinitdata, __devinitconst, and __devexit from these drivers. Based on patches originally written by Bill Pemberton, but redone by me in order to handle some of the coding style issues better, by hand. Cc: Bill Pemberton <wfp5p@virginia.edu> Cc: Adam Radford <linuxraid@lsi.com> Cc: "James E.J. Bottomley" <JBottomley@parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2009-12-05tree-wide: fix misspelling of "definition" in commentsAdam Buchbinder1-1/+1
"Definition" is misspelled "defintion" in several comments; this patch fixes them. No code changes. Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2006-09-26[SCSI] pci_module_init conversion in scsi subsystemHenrik Kretzschmar1-1/+1
Converts pci_module_init() to pci_register_driver() in the scsi subsys on 23 drivers which only return the value of pci_module_init(). Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-03[PATCH] irq-flags: scsi: Use the new IRQF_ constantsThomas Gleixner1-1/+1
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-12[SCSI] dmx3191d: fix a NULL pointer dereferenceAdrian Bunk1-1/+1
This patch fixes a NULL pointer dereference spotted by the Coverity checker. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-06-17[SCSI] Remove no-op implementations of SCSI EH hooksJeff Garzik1-2/+0
Drivers need not implement a hook that returns FAILED, and does nothing else, since the SCSI midlayer code will do that for us. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-04-17Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds1-0/+173
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!