| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
No functional change. Get "struct pcie_port *" from private data
pointer of "struct irq_domain" in dw_pcie_irq_domain_free() to make
it look similar to how "struct pcie_port *" is obtained in
dw_pcie_irq_domain_alloc()
Link: https://lore.kernel.org/r/20191220100550.777-1-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
|
|
The vim3l board does not work with a standard PCIe switch (ASM1184e),
spitting all kind of errors - hinting at HW misconfiguration (no link,
port enumeration issues, etc).
According to the the Synopsys DWC PCIe Reference Manual, in the section
dedicated to the PLCR register, bit 7 is described (FAST_LINK_MODE) as:
"Sets all internal timers to fast mode for simulation purposes."
it is sound to set this bit from a simulation perspective, but on actual
silicon, which expects timers to have a nominal value, it is not.
Make sure the FAST_LINK_MODE bit is cleared when configuring the RC
to solve this problem.
Link: https://lore.kernel.org/r/20200429164230.309922-1-maz@kernel.org
Fixes: 9c0ef6d34fdb ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
On a system that uses the internal DWC MSI widget, I get this
warning from debugfs when CONFIG_GENERIC_IRQ_DEBUGFS is selected:
debugfs: File ':soc:pcie@fc000000' in directory 'domains' already present!
This is due to the fact that the DWC MSI code tries to register two
IRQ domains for the same firmware node, without telling the low
level code how to distinguish them (by setting a bus token). This
further confuses debugfs which tries to create corresponding
files for each domain.
Fix it by tagging the inner domain as DOMAIN_BUS_NEXUS, which is
the closest thing we have as to "generic MSI".
Link: https://lore.kernel.org/r/20200501113921.366597-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
|
|
platform_get_resource() may fail and return NULL, so we had better
check its return value to avoid a NULL pointer dereference a bit later
in the code. Fix it to use devm_platform_ioremap_resource_byname()
instead of calling platform_get_resource_byname() and devm_ioremap().
Link: https://lore.kernel.org/r/20200429015027.134485-1-weiyongjun1@huawei.com
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Fix the following sparse warning:
drivers/pci/controller/dwc/pcie-intel-gw.c:456:5: warning: symbol
'intel_pcie_cpu_addr' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20200415084953.6533-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Function dw_pcie_prog_outbound_atu_unroll() does not program the upper
32-bit ATU limit register. Since ATU programming functions limit the
size of the translated region to 4GB by using a u32 size parameter,
these issues may combine into undefined behavior for resource sizes
with non-zero upper 32-bits.
For example, a 128GB address space starting at physical CPU address of
0x2000000000 with size of 0x2000000000 needs the following values
programmed into the lower and upper 32-bit limit registers:
0x3fffffff in the upper 32-bit limit register
0xffffffff in the lower 32-bit limit register
Currently, only the lower 32-bit limit register is programmed with a
value of 0xffffffff but the upper 32-bit limit register is not being
programmed. As a result, the upper 32-bit limit register remains at its
default value after reset of 0x0.
These issues may combine to produce undefined behavior since the ATU
limit address may be lower than the ATU base address. Programming the
upper ATU limit address register prevents such undefined behavior despite
the region size getting truncated due to the 32-bit size limit.
Link: https://lore.kernel.org/r/1585785493-23210-1-git-send-email-alan.mikhak@sifive.com
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
|
|
Per PCIe 5.0 r1.0, Terms and Acronyms, Page 80:
Reserved register fields must be read only and must return 0 (all 0's
for multi-bit fields) when read. Reserved encodings for register and
packet fields must not be used. Any implementation dependence on a
Reserved field value or encoding will result in an implementation that
is not PCI Express-compliant.
This patch ensures reads will return 0 for any bit not in the Read-Only,
Read-Write, or Write-1-to-Clear bitmasks.
Link: https://lore.kernel.org/r/20200511162117.6674-5-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Add missing bits from PCIe 4.0 and updates for PCIe 5.0 r1.0.
PCIe 4.0:
Device Status bit 6 - W1C - Emergency Power Reduction Detected
Link Control bits 15:14 - RW - DRS Signaling Control
Slot Control bit 13 - RW - Auto Slow Power Limit Disable
PCIe 5.0:
Slot Control bit 14 - RW - In-Band PD Disable
Link: https://lore.kernel.org/r/20200511162117.6674-4-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
The upper 16-bits of Root Control contain the Root Capabilities
register. The code instead describes the Root Status register in the
upper 16-bits, although it uses the correct bit definition for Root
Capabilities, and for Root Status in the next definition.
Fix this comment and add a comment describing the Root Status register.
Link: https://lore.kernel.org/r/20200511162117.6674-3-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
This patch fixes two bit conflicts in the pci-bridge-emul driver:
1. Bit 3 of Device Status (19 of Device Control) is marked as both
Write-1-to-Clear and Read-Only. It should be Write-1-to-Clear.
The Read-Only and Reserved bitmasks are shifted by 1 bit due to this
error.
2. Bit 12 of Slot Control is marked as both Read-Write and Reserved.
It should be Read-Write.
Link: https://lore.kernel.org/r/20200511162117.6674-2-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Add support for R-Car PCIe controller to work in endpoint mode.
Link: https://lore.kernel.org/r/1588854799-13710-8-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
R-Car PCIe controller has support to map multiple memory regions for
mapping the outbound memory in local system also the controller limits
single allocation for each region (that is, once a chunk is used from the
region it cannot be used to allocate a new one). This features inspires to
add support for handling multiple memory bases in endpoint framework.
With this patch pci_epc_mem_init() initializes address space for endpoint
controller which support single window and pci_epc_multi_mem_init()
initializes multiple windows supported by endpoint controller.
Link: https://lore.kernel.org/r/1588854799-13710-6-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Use bridge resource definitions instead of using the PCI_BRIDGE_RESOURCES
constant with an integer offeset.
Link: https://lore.kernel.org/r/20200520183411.1534621-2-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Except for Endpoints, we enable PTM at enumeration-time. Previously we did
not account for the fact that Switch Downstream Ports are not permitted to
have a PTM capability; their PTM behavior is controlled by the Upstream
Port (PCIe r5.0, sec 7.9.16). Since Downstream Ports don't have a PTM
capability, we did not mark them as "ptm_enabled", which meant that
pci_enable_ptm() on an Endpoint failed because there was no PTM path to it.
Mark Downstream Ports as "ptm_enabled" if their Upstream Port has PTM
enabled.
Fixes: eec097d43100 ("PCI: Add pci_enable_ptm() for drivers to enable PTM on endpoints")
Reported-by: Aditya Paluri <Venkata.AdityaPaluri@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
shpchp_unconfigure_device() always returned 0, so there's no reason for a
return value. In addition, remove_board() checked the return value for
possible error which is unnecessary.
Convert shpchp_unconfigure_device() to a void function and remove the
return value check. This addresses the following Coccinelle warning:
drivers/pci/hotplug/shpchp_pci.c:66:5-7: Unneeded variable: "rc". Return "0" on line 86
Link: https://lore.kernel.org/r/20200521190457.1066600-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use "true" instead of 1 to initialize "bool use_dma_mrpc". This resolves
the following Coccinelle warning:
drivers/pci/switch/switchtec.c:28:12-24: WARNING: Assignment of 0/1 to bool variable
Link: https://lore.kernel.org/r/20200521200439.1076672-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
|
|
Fix kernel-doc of the "srv" parameter to pcie_pme_resume() and
pcie_pme_remove(). Building with W=1 produced these warnings:
drivers/pci/pcie/pme.c:414: warning: Function parameter or member 'srv' not described in 'pcie_pme_resume'
drivers/pci/pcie/pme.c:437: warning: Function parameter or member 'srv' not described in 'pcie_pme_remove'
Link: https://lore.kernel.org/r/1589612414-61682-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
On s390 PCI Virtual Functions (VFs) are scanned by firmware and are made
available to Linux via the hot-plug interface. As such the common code
path of doing the scan directly using the parent Physical Function (PF)
is not used and fenced off with the no_vf_scan attribute.
Even if the partition created the VFs itself e.g. using the sriov_numvfs
attribute of a PF, the PF/VF links thus need to be established after the
fact. To do this when a VF is plugged we scan through all functions on
the same zbus and test whether they are the parent PF in which case we
establish the necessary links.
With these links established there is now no more need to fence off
pci_iov_remove_virtfn() for pdev->no_vf_scan as the common code now
works fine.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Link: https://lore.kernel.org/r/20200506154139.90609-3-schnelle@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Currently pci_iov_add_virtfn() scans the SR-IOV BARs, adds the VF to the
bus and also creates the sysfs links between the newly added VF and its
parent PF.
With pdev->no_vf_scan fencing off the entire pci_iov_add_virtfn() call
s390 as the sole pdev->no_vf_scan user thus ends up missing these sysfs
links which are required for example by QEMU/libvirt.
Instead of duplicating the code refactor pci_iov_add_virtfn() to make
sysfs link creation callable separately.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Link: https://lore.kernel.org/r/20200506154139.90609-1-schnelle@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The PCI Bus Binding specification (IEEE Std 1275-1994 Revision 2.1 [1])
defines both Vendor ID and Device ID to be 32-bits. Fix
pcie-cadence-host.c driver to read 32-bit Vendor ID and Device ID
properties from device tree.
[1] -> https://www.devicetree.org/open-firmware/bindings/pci/pci2_1.pdf
Link: https://lore.kernel.org/r/20200508130646.23939-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Joseph <tjoseph@cadence.com>
|
|
"cdns,max-outbound-regions" device tree property provides the
maximum number of outbound regions supported by the Host PCIe
controller. However the outbound regions are configured based
on what is populated in the "ranges" DT property.
Avoid using two properties for configuring outbound regions and
use only "ranges" property instead.
Link: https://lore.kernel.org/r/20200508130646.23939-3-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Joseph <tjoseph@cadence.com>
|
|
PCI-E capability macros are already defined in linux/pci_regs.h.
Remove their reimplementation in pcie-aardvark.
Link: https://lore.kernel.org/r/20200430080625.26070-9-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
|
|
With recent proposed changes for U-Boot it is possible that bootloader
won't initialize the PHY for this controller (currently the PHY is
initialized regardless whether PCI is used in U-Boot, but with these
proposed changes the PHY is initialized only on request).
Since the mvebu-a3700-comphy driver by Miquèl Raynal supports enabling
PCIe PHY, and since Linux' functionality should be independent on what
bootloader did, add code for enabling generic PHY if found in device OF
node.
The mvebu-a3700-comphy driver does PHY powering via SMC calls to ARM
Trusted Firmware. The corresponding code in ARM Trusted Firmware skips
one register write which U-Boot does not: step 7 ("Enable TX"), see [1].
Instead ARM Trusted Firmware expects PCIe driver to do this step,
probably because the register is in PCIe controller address space,
instead of PHY address space. We therefore add this step into the
advk_pcie_setup_hw function.
[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/tree/drivers/marvell/comphy/phy-comphy-3700.c?h=v2.3-rc2#n836
Link: https://lore.kernel.org/r/20200430080625.26070-8-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquèl Raynal <miquel.raynal@bootlin.com>
|
|
This register is applicable only when the controller is configured for
Endpoint mode, which is not the case for the current version of this
driver.
Attempting to remove this code though caused some ath10k cards to stop
working, so for some unknown reason it is needed here.
This should be investigated and a comment explaining this should be put
before the code, so we add a FIXME comment for now.
Link: https://lore.kernel.org/r/20200430080625.26070-7-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
|
|
Add support for issuing PERST via GPIO specified in 'reset-gpios'
property (as described in PCI device tree bindings).
Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
after reboot when PERST is not issued during driver initialization.
If bootloader already enabled link training then issuing PERST has no
effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
not detected. We therefore clear the LINK_TRAINING_EN register before.
It was observed that Compex WLE900VX card needs to be in PERST reset
for at least 10ms if bootloader enabled link training.
Tested on Turris MOX.
Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
|
|
Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.
Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.
To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.
Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
|
|
Interpret zero value of max-link-speed property as invalid,
as the device tree bindings documentation specifies.
Link: https://lore.kernel.org/r/20200430080625.26070-4-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
|
|
register
Trying to change Link Status register does not have any effect as this
is a read-only register. Trying to overwrite bits for Negotiated Link
Width does not make sense.
In future proper change of link width can be done via Lane Count Select
bits in PCIe Control 0 register.
Trying to unconditionally enable ASPM L0s via ASPM Control bits in Link
Control register is wrong. There should be at least some detection if
endpoint supports L0s as isn't mandatory.
Moreover ASPM Control bits in Link Control register are controlled by
pcie/aspm.c code which sets it according to system ASPM settings,
immediately after aardvark driver probes. So setting these bits by
aardvark driver has no long running effect.
Remove code which touches ASPM L0s bits from this driver and let
kernel's ASPM implementation to set ASPM state properly.
Some users are reporting issues that this code is problematic for some
Intel wifi cards and removing it fixes them, see e.g.:
https://bugzilla.kernel.org/show_bug.cgi?id=196339
If problems with Intel wifi cards occur even after this commit, then
pcie/aspm.c code could be modified / hooked to not enable ASPM L0s state
for affected problematic cards.
Link: https://lore.kernel.org/r/20200430080625.26070-3-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
|
|
Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
training and starting link training causes detection issues with some
buggy cards (such as Compex WLE900VX).
Move the code which enables link training immediately before the one
which starts link traning.
This fixes detection issues of Compex WLE900VX card on Turris MOX after
cold boot.
Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org
Fixes: f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready...")
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
|
|
Kai-Heng Feng reported that it takes a long time (> 1 s) to resume
Thunderbolt-connected devices from both runtime suspend and system sleep
(s2idle).
This was because some Downstream Ports that support > 5 GT/s do not also
support Data Link Layer Link Active reporting. Per PCIe r5.0 sec 6.6.1:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Sec 7.5.3.6 requires such Ports to support DLL Link Active reporting, but
at least the Intel JHL6240 Thunderbolt 3 Bridge [8086:15c0] and the Intel
JHL7540 Thunderbolt 3 Bridge [8086:15ea] do not.
Previously we tried to wait for Link training to complete, but since there
was no DLL Link Active reporting, all we could do was wait the worst-case
1000 ms, then another 100 ms.
Instead of using the supported speeds to determine whether to wait for Link
training, check whether the port supports DLL Link Active reporting. The
Ports in question do not, so we'll wait only the 100 ms required for Ports
that support Link speeds <= 5 GT/s.
This of course assumes these Ports always train the Link within 100 ms even
if they are operating at > 5 GT/s, which is not required by the spec.
[bhelgaas: commit log, comment]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206837
Link: https://lore.kernel.org/r/20200514133043.27429-1-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The caller of pcie_wait_for_link_delay() specifies the time to wait after
the link becomes active. When the downstream port doesn't support link
active reporting, obviously we can't tell when the link becomes active, so
we waited the worst-case time (1000 ms) plus 100 ms, ignoring the delay
from the caller.
Instead, wait for 1000 ms + the delay from the caller.
Fixes: 4827d63891b6 ("PCI/PM: Add pcie_wait_for_link_delay()")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Root Complex Integrated Endpoints (RCiEPs) do not have an upstream bridge,
so pci_configure_mps() previously ignored them, which may result in reduced
performance.
Instead, program the Max_Payload_Size of RCiEPs to the maximum supported
value (unless it is limited for the PCIE_BUS_PEER2PEER case). This also
affects the subsequent programming of Max_Read_Request_Size because Linux
programs MRRS based on the MPS value.
Fixes: 9dae3a97297f ("PCI: Move MPS configuration check to pci_configure_device()")
Link: https://lore.kernel.org/r/1585343775-4019-1-git-send-email-ashok.raj@intel.com
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
|
|
The PCI code has several paths where the struct pci_host_bridge is freed
directly. This is wrong because it contains a struct device which is
refcounted and should be freed using put_device(). This can result in
use-after-free errors. I think this problem has existed since 2012 with
commit 7b5436635800 ("PCI: add generic device into pci_host_bridge
struct"). It generally hasn't mattered as most host bridge drivers are
still built-in and can't unbind.
The problem is a struct device should never be freed directly once
device_initialize() is called and a ref is held, but that doesn't happen
until pci_register_host_bridge(). There's then a window between allocating
the host bridge and pci_register_host_bridge() where kfree should be used.
This is fragile and requires callers to do the right thing. To fix this, we
need to split device_register() into device_initialize() and device_add()
calls, so that the host bridge struct is always freed by using a
put_device().
devm_pci_alloc_host_bridge() is using devm_kzalloc() to allocate struct
pci_host_bridge which will be freed directly. Instead, we can use a custom
devres action to call put_device().
Link: https://lore.kernel.org/r/20200513223859.11295-2-robh@kernel.org
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
If device_register() has an error, we should bail out of
pci_register_host_bridge() rather than continuing on.
Fixes: 37d6a0a6f470 ("PCI: Add pci_register_host_bridge() interface")
Link: https://lore.kernel.org/r/20200513223859.11295-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
Previously we used pcie_find_root_port() to find a Root Port from a PCIe
device and pci_find_pcie_root_port() to find a Root Port from a
Conventional PCI device.
Unify the two functions and use pcie_find_root_port() to find a Root Port
from either a Conventional PCI device or a PCIe device. Then there is no
need to distinguish the type of the device.
Link: https://lore.kernel.org/r/1589019568-5216-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # thunderbolt
|
|
xHCI's PCI fixup, run at the end of pcie-brcmstb's probe, depends on
RPi4's VideoCore firmware interface to be up and running. It's possible
for both initializations to race, so make sure it's available prior to
starting.
Link: https://lore.kernel.org/r/20200505161318.26200-4-nsaenzjulienne@suse.de
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
The current codebase makes use of the zero-length array language extension
to the C90 standard, but the preferred mechanism to declare variable-length
types such as these as a flexible array member [1][2], introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning in
case the flexible array does not occur last in the structure, which will
help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that dynamic memory allocations won't be affected by this
change:
Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero. [1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type [1]. There are some instances of code in which
the sizeof() operator is being incorrectly/erroneously applied to
zero-length arrays, and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also help
to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Link: https://lore.kernel.org/r/20200507190544.GA15633@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The platform_get_irq*() interfaces return either a negative error number or
a valid IRQ. 0 is not a valid return value, so check for "< 0" to detect
failure as recommended by the function documentation.
On failure, return the error number from platform_get_irq*() instead of
making up a new one.
Link: https://lore.kernel.org/r/cover.1583952275.git.amanharitsh123@gmail.com
[bhelgaas: commit log, squash into one patch]
Signed-off-by: Aman Sharma <amanharitsh123@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
|
|
When kdump is triggered, some PCI devices may have not been shut down
cleanly before the kdump kernel starts.
This causes the initial attempt to enter D0 state in the kdump kernel to
fail with invalid device state returned from Hyper-V host.
When this happens, explicitly call hv_pci_bus_exit() and retry to enter
the D0 state.
Link: https://lore.kernel.org/r/20200507050300.10974-1-weh@microsoft.com
Signed-off-by: Wei Hu <weh@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
|
|
In some error cases in hv_pci_probe(), allocated resources are not freed.
Fix this by adding a field to keep track of the high water mark for slots
that have resources allocated to them. In case of an error, this high
water mark is used to know which slots have resources that must be released.
Since slots are numbered starting with zero, a value of -1 indicates no
slots have been allocated resources. There may be unused slots in the range
between slot 0 and the high water mark slot, but these slots are already
ignored by the existing code in the allocate and release loops with the call
to get_pcichild_wslot().
Link: https://lore.kernel.org/r/20200507050211.10923-1-weh@microsoft.com
Signed-off-by: Wei Hu <weh@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
|
|
Some informal internal experiments has shown that the BrcmSTB ASPM L0s
savings may introduce an undesirable noise signal on some customers'
boards. In addition, L0s was found lacking in realized power savings,
especially relative to the L1 ASPM component. This is BrcmSTB's
experience and may not hold for others. At any rate, if the
'aspm-no-l0s' property is present L0s will be disabled.
Link: https://lore.kernel.org/r/20200507201544.43432-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
|
|
The outbound memory window registers were being referenced
with an incorrect stride offset. This probably wasn't noticed
previously as there was likely only one such window employed.
Link: https://lore.kernel.org/r/20200507201544.43432-3-james.quinlan@broadcom.com
Fixes: c0452137034b ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
|
|
clk_put() was being invoked on a clock obtained by
devm_clk_get_optional().
Link: https://lore.kernel.org/r/20200507201544.43432-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
|
|
While preparing the driver for upstream this detail was missed.
If not asserted during the initialization process, devices connected on
the bus will not be made aware of the internal reset happening. This,
potentially resulting in unexpected behavior.
Link: https://lore.kernel.org/r/20200507172020.18000-1-nsaenzjulienne@suse.de
Fixes: c0452137034b ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
pci_epc_mem_init() internally used page size equal to *PAGE_SIZE* to
manage the address space so instead just pass the page size as a
argument to pci_epc_mem_init().
Also make pci_epc_mem_init() as a C function instead of a macro function
in preparation for adding support for pci-epc-mem core to handle multiple
windows.
Link: https://lore.kernel.org/r/1588854799-13710-5-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The mask value was calculated incorrectly for PCIEPAMR register if the
size was less than 128 bytes. Fix this issue by adding a check on size.
Link: https://lore.kernel.org/r/1588854799-13710-4-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
Move shareable code to common file pcie-rcar.c and the #defines to
pcie-rcar.h so that the common code can be reused with endpoint driver.
There are no functional changes with this patch for the host controller
driver.
Link: https://lore.kernel.org/r/1588854799-13710-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
This commit renames pcie-rcar.c to pcie-rcar-host.c in preparation for
adding support for endpoint mode. CONFIG_PCIE_RCAR is kept so that arm64
defconfig change can be a separate patch.
With this patch both config options PCIE_RCAR and PCIE_RCAR_HOST will be
available but PCIE_RCAR internally selects PCIE_RCAR_HOST so that bisect
builds wont be affected.
Link: https://lore.kernel.org/r/1588854799-13710-2-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
Error code is stored in rp->reset_gpio and not in err variable.
Link: https://lore.kernel.org/r/20200414102512.27506-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Use the new acpi_evaluate_reg() helper in the acpiphp_glue.c code.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
