| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit f5eff5591b8f9c5effd25c92c758a127765f74c1 upstream.
In 2013, commits
2e35afaefe64 ("PCI: pciehp: Add reset_slot() method")
608c388122c7 ("PCI: Add slot reset option to pci_dev_reset()")
amended PCIe hotplug to mask Presence Detect Changed events during a
Secondary Bus Reset. The reset thus no longer causes gratuitous slot
bringdown and bringup.
However the commits neglected to serialize reset with code paths reading
slot registers. For instance, a slot bringup due to an earlier hotplug
event may see the Presence Detect State bit cleared during a concurrent
Secondary Bus Reset.
In 2018, commit
5b3f7b7d062b ("PCI: pciehp: Avoid slot access during reset")
retrofitted the missing locking. It introduced a reset_lock which
serializes a Secondary Bus Reset with other parts of pciehp.
Unfortunately the locking turns out to be overzealous: reset_lock is
held for the entire enumeration and de-enumeration of hotplugged devices,
including driver binding and unbinding.
Driver binding and unbinding acquires device_lock while the reset_lock
of the ancestral hotplug port is held. A concurrent Secondary Bus Reset
acquires the ancestral reset_lock while already holding the device_lock.
The asymmetric locking order in the two code paths can lead to AB-BA
deadlocks.
Michael Haeuptle reports such deadlocks on simultaneous hot-removal and
vfio release (the latter implies a Secondary Bus Reset):
pciehp_ist() # down_read(reset_lock)
pciehp_handle_presence_or_link_change()
pciehp_disable_slot()
__pciehp_disable_slot()
remove_board()
pciehp_unconfigure_device()
pci_stop_and_remove_bus_device()
pci_stop_bus_device()
pci_stop_dev()
device_release_driver()
device_release_driver_internal()
__device_driver_lock() # device_lock()
SYS_munmap()
vfio_device_fops_release()
vfio_device_group_close()
vfio_device_close()
vfio_device_last_close()
vfio_pci_core_close_device()
vfio_pci_core_disable() # device_lock()
__pci_reset_function_locked()
pci_reset_bus_function()
pci_dev_reset_slot_function()
pci_reset_hotplug_slot()
pciehp_reset_slot() # down_write(reset_lock)
Ian May reports the same deadlock on simultaneous hot-removal and an
AER-induced Secondary Bus Reset:
aer_recover_work_func()
pcie_do_recovery()
aer_root_reset()
pci_bus_error_reset()
pci_slot_reset()
pci_slot_lock() # device_lock()
pci_reset_hotplug_slot()
pciehp_reset_slot() # down_write(reset_lock)
Fix by releasing the reset_lock during driver binding and unbinding,
thereby splitting and shrinking the critical section.
Driver binding and unbinding is protected by the device_lock() and thus
serialized with a Secondary Bus Reset. There's no need to additionally
protect it with the reset_lock. However, pciehp does not bind and
unbind devices directly, but rather invokes PCI core functions which
also perform certain enumeration and de-enumeration steps.
The reset_lock's purpose is to protect slot registers, not enumeration
and de-enumeration of hotplugged devices. That would arguably be the
job of the PCI core, not the PCIe hotplug driver. After all, an
AER-induced Secondary Bus Reset may as well happen during boot-time
enumeration of the PCI hierarchy and there's no locking to prevent that
either.
Exempting *de-enumeration* from the reset_lock is relatively harmless:
A concurrent Secondary Bus Reset may foil config space accesses such as
PME interrupt disablement. But if the device is physically gone, those
accesses are pointless anyway. If the device is physically present and
only logically removed through an Attention Button press or the sysfs
"power" attribute, PME interrupts as well as DMA cannot come through
because pciehp_unconfigure_device() disables INTx and Bus Master bits.
That's still protected by the reset_lock in the present commit.
Exempting *enumeration* from the reset_lock also has limited impact:
The exempted call to pci_bus_add_device() may perform device accesses
through pcibios_bus_add_device() and pci_fixup_device() which are now
no longer protected from a concurrent Secondary Bus Reset. Otherwise
there should be no impact.
In essence, the present commit seeks to fix the AB-BA deadlocks while
still retaining a best-effort reset protection for enumeration and
de-enumeration of hotplugged devices -- until a general solution is
implemented in the PCI core.
Link: https://lore.kernel.org/linux-pci/CS1PR8401MB0728FC6FDAB8A35C22BD90EC95F10@CS1PR8401MB0728.NAMPRD84.PROD.OUTLOOK.COM
Link: https://lore.kernel.org/linux-pci/20200615143250.438252-1-ian.may@canonical.com
Link: https://lore.kernel.org/linux-pci/ce878dab-c0c4-5bd0-a725-9805a075682d@amd.com
Link: https://lore.kernel.org/linux-pci/ed831249-384a-6d35-0831-70af191e9bce@huawei.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215590
Fixes: 5b3f7b7d062b ("PCI: pciehp: Avoid slot access during reset")
Link: https://lore.kernel.org/r/fef2b2e9edf245c049a8c5b94743c0f74ff5008a.1681191902.git.lukas@wunner.de
Reported-by: Michael Haeuptle <michael.haeuptle@hpe.com>
Reported-by: Ian May <ian.may@canonical.com>
Reported-by: Andrey Grodzovsky <andrey2805@gmail.com>
Reported-by: Rahul Kumar <rahul.kumar1@amd.com>
Reported-by: Jialin Zhang <zhangjialin11@huawei.com>
Tested-by: Anatoli Antonovitch <Anatoli.Antonovitch@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Dan Stein <dstein@hpe.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Alex Michon <amichon@kalrayinc.com>
Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Sathyanarayanan Kuppuswamy <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 085a9f43433f30cbe8a1ade62d9d7827c3217f4d upstream.
Use down_read_nested() and down_write_nested() when taking the
ctrl->reset_lock rw-sem, passing the number of PCIe hotplug controllers in
the path to the PCI root bus as lock subclass parameter.
This fixes the following false-positive lockdep report when unplugging a
Lenovo X1C8 from a Lenovo 2nd gen TB3 dock:
pcieport 0000:06:01.0: pciehp: Slot(1): Link Down
pcieport 0000:06:01.0: pciehp: Slot(1): Card not present
============================================
WARNING: possible recursive locking detected
5.16.0-rc2+ #621 Not tainted
--------------------------------------------
irq/124-pciehp/86 is trying to acquire lock:
ffff8e5ac4299ef8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_check_presence+0x23/0x80
but task is already holding lock:
ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&ctrl->reset_lock);
lock(&ctrl->reset_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by irq/124-pciehp/86:
#0: ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180
#1: ffffffffa3b024e8 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pciehp_unconfigure_device+0x31/0x110
#2: ffff8e5ac1ee2248 (&dev->mutex){....}-{3:3}, at: device_release_driver+0x1c/0x40
stack backtrace:
CPU: 4 PID: 86 Comm: irq/124-pciehp Not tainted 5.16.0-rc2+ #621
Hardware name: LENOVO 20U90SIT19/20U90SIT19, BIOS N2WET30W (1.20 ) 08/26/2021
Call Trace:
<TASK>
dump_stack_lvl+0x59/0x73
__lock_acquire.cold+0xc5/0x2c6
lock_acquire+0xb5/0x2b0
down_read+0x3e/0x50
pciehp_check_presence+0x23/0x80
pciehp_runtime_resume+0x5c/0xa0
device_for_each_child+0x45/0x70
pcie_port_device_runtime_resume+0x20/0x30
pci_pm_runtime_resume+0xa7/0xc0
__rpm_callback+0x41/0x110
rpm_callback+0x59/0x70
rpm_resume+0x512/0x7b0
__pm_runtime_resume+0x4a/0x90
__device_release_driver+0x28/0x240
device_release_driver+0x26/0x40
pci_stop_bus_device+0x68/0x90
pci_stop_bus_device+0x2c/0x90
pci_stop_and_remove_bus_device+0xe/0x20
pciehp_unconfigure_device+0x6c/0x110
pciehp_disable_slot+0x5b/0xe0
pciehp_handle_presence_or_link_change+0xc3/0x2f0
pciehp_ist+0x179/0x180
This lockdep warning is triggered because with Thunderbolt, hotplug ports
are nested. When removing multiple devices in a daisy-chain, each hotplug
port's reset_lock may be acquired recursively. It's never the same lock, so
the lockdep splat is a false positive.
Because locks at the same hierarchy level are never acquired recursively, a
per-level lockdep class is sufficient to fix the lockdep warning.
The choice to use one lockdep subclass per pcie-hotplug controller in the
path to the root-bus was made to conserve class keys because their number
is limited and the complexity grows quadratically with number of keys
according to Documentation/locking/lockdep-design.rst.
Link: https://lore.kernel.org/linux-pci/20190402021933.GA2966@mit.edu/
Link: https://lore.kernel.org/linux-pci/de684a28-9038-8fc6-27ca-3f6f2f6400d7@redhat.com/
Link: https://lore.kernel.org/r/20211217141709.379663-1-hdegoede@redhat.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208855
Reported-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
[lukas: backport to v4.19-stable]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63ba51db24ed1b8f8088a897290eb6c036c5435d upstream.
PCI passthrough to VMs does not work with AMD FCH AHCI adapters: the guest
OS fails to correctly probe devices attached to the controller due to FIS
communication failures:
ata4: softreset failed (1st FIS failed)
...
ata4.00: qc timeout after 5000 msecs (cmd 0xec)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
Forcing the "bus" reset method before unbinding & binding the adapter to
the vfio-pci driver solves this issue, e.g.:
echo "bus" > /sys/bus/pci/devices/<ID>/reset_method
gives a working guest OS, indicating that the default FLR reset method
doesn't work correctly.
Apply quirk_no_flr() to AMD FCH AHCI devices to work around this issue.
Link: https://lore.kernel.org/r/20230128013951.523247-1-damien.lemoal@opensource.wdc.com
Reported-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa382ffa705bea9931ec92b6f3c70e1fdb372195 upstream.
When pci_create_attr() fails, pci_remove_resource_files() is called which
will iterate over the res_attr[_wc] arrays and frees every non NULL entry.
To avoid a double free here set the array entry only after it's clear we
successfully initialized it.
Fixes: b562ec8f74e4 ("PCI: Don't leak memory if sysfs_create_bin_file() fails")
Link: https://lore.kernel.org/r/20221007070735.GX986@pengutronix.de/
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 98b04dd0b4577894520493d96bc4623387767445 upstream.
pci_device_is_present() previously didn't work for VFs because it reads the
Vendor and Device ID, which are 0xffff for VFs, which looks like they
aren't present. Check the PF instead.
Wei Gong reported that if virtio I/O is in progress when the driver is
unbound or "0" is written to /sys/.../sriov_numvfs, the virtio I/O
operation hangs, which may result in output like this:
task:bash state:D stack: 0 pid: 1773 ppid: 1241 flags:0x00004002
Call Trace:
schedule+0x4f/0xc0
blk_mq_freeze_queue_wait+0x69/0xa0
blk_mq_freeze_queue+0x1b/0x20
blk_cleanup_queue+0x3d/0xd0
virtblk_remove+0x3c/0xb0 [virtio_blk]
virtio_dev_remove+0x4b/0x80
...
device_unregister+0x1b/0x60
unregister_virtio_device+0x18/0x30
virtio_pci_remove+0x41/0x80
pci_device_remove+0x3e/0xb0
This happened because pci_device_is_present(VF) returned "false" in
virtio_pci_remove(), so it called virtio_break_device(). The broken vq
meant that vring_interrupt() skipped the vq.callback() that would have
completed the virtio I/O operation via virtblk_done().
[bhelgaas: commit log, simplify to always use pci_physfn(), add stable tag]
Link: https://lore.kernel.org/r/20221026060912.173250-1-mst@redhat.com
Reported-by: Wei Gong <gongwei833x@gmail.com>
Tested-by: Wei Gong <gongwei833x@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2d9cd957d40c3ac491b358e7cff0515bb07a3a9c ]
When kvasprintf() fails to allocate memory, it returns a NULL pointer.
Return error from pci_request_irq() so we don't dereference it.
[bhelgaas: commit log]
Fixes: 704e8953d3e9 ("PCI/irq: Add pci_request_irq() and pci_free_irq() helpers")
Link: https://lore.kernel.org/r/20221121020029.3759444-1-zengheng4@huawei.com
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0e32818397426a688f598f35d3bc762eca6d7592 upstream.
When pci_assign_resource() is unable to assign resources to a BAR, it uses
pci_revert_fw_address() to fall back to a firmware assignment (if any).
Previously pci_revert_fw_address() assumed all addresses could reach the
device, but this is not true if the device is below a bridge that only
forwards addresses within its windows.
This problem was observed on a Tyan Tomcat IV S1564D system where the BIOS
did not assign valid addresses to several bridges and USB devices:
pci 0000:00:11.0: PCI-to-PCIe bridge to [bus 01-ff]
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: PCIe Upstream Port to [bus 02-ff]
pci 0000:01:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:02:02.0: PCIe Downstream Port to [bus 05-ff]
pci 0000:02:02.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:05:00.0: PCIe-to-PCI bridge to [bus 06-ff]
pci 0000:05:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:06:08.0: USB UHCI 1.1
pci 0000:06:08.0: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.1: USB UHCI 1.1
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.0: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
pci 0000:06:08.1: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
During the first pass of assigning unassigned resources, there was not
enough I/O space available, so we couldn't assign the 06:08.0 BAR and
reverted to the firmware assignment (still unreachable). Reverting the
06:08.1 assignment failed because it conflicted with 06:08.0:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: no space for bridge window [io size 0x2000]
pci 0000:02:02.0: no space for bridge window [io size 0x1000]
pci 0000:05:00.0: no space for bridge window [io size 0x1000]
pci 0000:06:08.0: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.0: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.1: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] conflicts with 0000:06:08.0 [io 0xfce0-0xfcff]
A subsequent pass assigned valid bridge windows and a valid 06:08.1 BAR,
but left the 06:08.0 BAR alone, so the UHCI device was still unusable:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff] released
pci 0000:00:11.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:01:00.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:02:02.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:05:00.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:06:08.0: BAR 4: assigned [io 0xfce0-0xfcff] # left alone
pci 0000:06:08.1: BAR 4: assigned [io 0x2000-0x201f]
...
uhci_hcd 0000:06:08.0: host system error, PCI problems?
uhci_hcd 0000:06:08.0: host controller process error, something bad happened!
uhci_hcd 0000:06:08.0: host controller halted, very bad!
uhci_hcd 0000:06:08.0: HCRESET not completed yet!
uhci_hcd 0000:06:08.0: HC died; cleaning up
If the address assigned by firmware is not reachable because it's not
within upstream bridge windows, fail instead of assigning the unusable
address from firmware.
[bhelgaas: commit log, use pci_upstream_bridge()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=16263
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203012338460.46819@angie.orcam.me.uk
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209211921250.29493@angie.orcam.me.uk
Fixes: 58c84eda0756 ("PCI: fall back to original BIOS BAR addresses")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.35+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit afd306a65cedb9589564bdb23a0c368abc4215fd ]
The Broadcom BCM5750x NICs may be multi-function devices. They do not
advertise ACS capability. Peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for these devices so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
Link: https://lore.kernel.org/r/1654796507-28610-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a2bad844a67b1c7740bda63e87453baf63c3a7f7 upstream.
According to Dexuan, the hypervisor folks beleive that multi-msi
allocations are not correct. compose_msi_msg() will allocate multi-msi
one by one. However, multi-msi is a block of related MSIs, with alignment
requirements. In order for the hypervisor to allocate properly aligned
and consecutive entries in the IOMMU Interrupt Remapping Table, there
should be a single mapping request that requests all of the multi-msi
vectors in one shot.
Dexuan suggests detecting the multi-msi case and composing a single
request related to the first MSI. Then for the other MSIs in the same
block, use the cached information. This appears to be viable, so do it.
4.19 backport - add hv_msi_get_int_vector helper function. Fixed merge
conflict due to delivery_mode name change (APIC_DELIVERY_MODE_FIXED
is the value given to dest_Fixed). Removed unused variable in
hv_compose_msi_msg. Fixed reference to msi_desc->pci to point to
the same is_msix variable. Removed changes to compose_msi_req_v3 since
it doesn't exist yet.
Suggested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1652282599-21643-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b4b77778ecc5bfbd4e77de1b2fd5c1dd3c655f1f upstream.
Currently if compose_msi_msg() is called multiple times, it will free any
previous IRTE allocation, and generate a new allocation. While nothing
prevents this from occurring, it is extraneous when Linux could just reuse
the existing allocation and avoid a bunch of overhead.
However, when future IRTE allocations operate on blocks of MSIs instead of
a single line, freeing the allocation will impact all of the lines. This
could cause an issue where an allocation of N MSIs occurs, then some of
the lines are retargeted, and finally the allocation is freed/reallocated.
The freeing of the allocation removes all of the configuration for the
entire block, which requires all the lines to be retargeted, which might
not happen since some lines might already be unmasked/active.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1652282582-21595-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 455880dfe292a2bdd3b4ad6a107299fce610e64b upstream.
In the multi-MSI case, hv_arch_irq_unmask() will only operate on the first
MSI of the N allocated. This is because only the first msi_desc is cached
and it is shared by all the MSIs of the multi-MSI block. This means that
hv_arch_irq_unmask() gets the correct address, but the wrong data (always
0).
This can break MSIs.
Lets assume MSI0 is vector 34 on CPU0, and MSI1 is vector 33 on CPU0.
hv_arch_irq_unmask() is called on MSI0. It uses a hypercall to configure
the MSI address and data (0) to vector 34 of CPU0. This is correct. Then
hv_arch_irq_unmask is called on MSI1. It uses another hypercall to
configure the MSI address and data (0) to vector 33 of CPU0. This is
wrong, and results in both MSI0 and MSI1 being routed to vector 33. Linux
will observe extra instances of MSI1 and no instances of MSI0 despite the
endpoint device behaving correctly.
For the multi-MSI case, we need unique address and data info for each MSI,
but the cached msi_desc does not provide that. However, that information
can be gotten from the int_desc cached in the chip_data by
compose_msi_msg(). Fix the multi-MSI case to use that cached information
instead. Since hv_set_msi_entry_from_desc() is no longer applicable,
remove it.
4.19 backport - hv_set_msi_entry_from_desc doesn't exist to be removed.
int_entry replaces msi_entry for location int_desc is written to.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1651068453-29588-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08e61e861a0e47e5e1a3fb78406afd6b0cea6b6d upstream.
If the allocation of multiple MSI vectors for multi-MSI fails in the core
PCI framework, the framework will retry the allocation as a single MSI
vector, assuming that meets the min_vecs specified by the requesting
driver.
Hyper-V advertises that multi-MSI is supported, but reuses the VECTOR
domain to implement that for x86. The VECTOR domain does not support
multi-MSI, so the alloc will always fail and fallback to a single MSI
allocation.
In short, Hyper-V advertises a capability it does not implement.
Hyper-V can support multi-MSI because it coordinates with the hypervisor
to map the MSIs in the IOMMU's interrupt remapper, which is something the
VECTOR domain does not have. Therefore the fix is simple - copy what the
x86 IOMMU drivers (AMD/Intel-IR) do by removing
X86_IRQ_ALLOC_CONTIGUOUS_VECTORS after calling the VECTOR domain's
pci_msi_prepare().
4.19 backport - adds the hv_msi_prepare wrapper function.
X86_IRQ_ALLOC_TYPE_PCI_MSI changed to X86_IRQ_ALLOC_TYPE_MSI
(same value).
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1649856981-14649-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83013631f0f9961416abd812e228c8efbc2f6069 upstream.
Undo the PHY initialisation (e.g. balance runtime PM) if host
initialisation fails during probe.
Link: https://lore.kernel.org/r/20220401133854.10421-3-johan+linaro@kernel.org
Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.5
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 87d83b96c8d6c6c2d2096bd0bdba73bcf42b8ef0 upstream.
Drop the leftover pm_runtime_disable() calls from the late probe error
paths that would, for example, prevent runtime PM from being reenabled
after a probe deferral.
Link: https://lore.kernel.org/r/20220401133854.10421-2-johan+linaro@kernel.org
Fixes: 6e5da6f7d824 ("PCI: qcom: Fix error handling in runtime PM support")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.20
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 12068bb346db5776d0ec9bb4cd073f8427a1ac92 upstream.
92597f97a40b ("PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold") omitted
braces around the new Elo i2 entry, so it overwrote the existing Gigabyte
X299 entry. Add the appropriate braces.
Found by:
$ make W=1 drivers/pci/pci.o
CC drivers/pci/pci.o
drivers/pci/pci.c:2974:12: error: initialized field overwritten [-Werror=override-init]
2974 | .ident = "Elo i2",
| ^~~~~~~~
Link: https://lore.kernel.org/r/20220526221258.GA409855@bhelgaas
Fixes: 92597f97a40b ("PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 096950e230b8d83645c7cf408b9f399f58c08b96 ]
The ep->ob_region_map bitmap is a long and it has BITS_PER_LONG bits.
Link: https://lore.kernel.org/r/20220315065944.GB13572@kili
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0aa3a0937feeb91a0e4e438c3c063b749b194192 ]
The ep->ob_region_map bitmap is a long and it has BITS_PER_LONG bits.
Link: https://lore.kernel.org/r/20220315065829.GA13572@kili
Fixes: 37dddf14f1ae ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a91ee0e9fca9d7501286cfbced9b30a33e52740a ]
The sysfs sriov_numvfs_store() path acquires the device lock before the
config space access lock:
sriov_numvfs_store
device_lock # A (1) acquire device lock
sriov_configure
vfio_pci_sriov_configure # (for example)
vfio_pci_core_sriov_configure
pci_disable_sriov
sriov_disable
pci_cfg_access_lock
pci_wait_cfg # B (4) wait for dev->block_cfg_access == 0
Previously, pci_dev_lock() acquired the config space access lock before the
device lock:
pci_dev_lock
pci_cfg_access_lock
dev->block_cfg_access = 1 # B (2) set dev->block_cfg_access = 1
device_lock # A (3) wait for device lock
Any path that uses pci_dev_lock(), e.g., pci_reset_function(), may
deadlock with sriov_numvfs_store() if the operations occur in the sequence
(1) (2) (3) (4).
Avoid the deadlock by reversing the order in pci_dev_lock() so it acquires
the device lock before the config space access lock, the same as the
sriov_numvfs_store() path.
[bhelgaas: combined and adapted commit log from Jay Zhou's independent
subsequent posting:
https://lore.kernel.org/r/20220404062539.1710-1-jianjay.zhou@huawei.com]
Link: https://lore.kernel.org/linux-pci/1583489997-17156-1-git-send-email-yangyicong@hisilicon.com/
Also-posted-by: Jay Zhou <jianjay.zhou@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 92597f97a40bf661bebceb92e26ff87c76d562d4 upstream.
If a Root Port on Elo i2 is put into D3cold and then back into D0, the
downstream device becomes permanently inaccessible, so add a bridge D3 DMI
quirk for that system.
This was exposed by 14858dcc3b35 ("PCI: Use pci_update_current_state() in
pci_enable_device_flags()"), but before that commit the Root Port in
question had never been put into D3cold for real due to a mismatch between
its power state retrieved from the PCI_PM_CTRL register (which was
accessible even though the platform firmware indicated that the port was in
D3cold) and the state of an ACPI power resource involved in its power
management.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215715
Link: https://lore.kernel.org/r/11980172.O9o76ZdvQC@kreacher
Reported-by: Stefan Gottwald <gottwald@igel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 805dfc18dd3d4dd97a987d4406593b5a225b1253 upstream.
In advk_pcie_handle_msi() it is expected that when bit i in the W1C
register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is
updated to contain the MSI number corresponding to index i.
Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG
always contains the number of the last received MSI, overall.
Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt
number. Since Aardvark already forbids more than 32 interrupts and uses
own allocated hwirq numbers, the msi_idx already corresponds to the
received MSI number.
Link: https://lore.kernel.org/r/20220110015018.26359-3-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d8dc1f7cd007a7ce94c5b4c20d63a8b8d6d7751 upstream.
We already clear all the other interrupts (ISR0, ISR1, HOST_CTRL_INT).
Define a new macro PCIE_MSI_ALL_MASK and do the same clearing for MSIs,
to ensure that we don't start receiving spurious interrupts.
Use this new mask in advk_pcie_handle_msi();
Link: https://lore.kernel.org/r/20211130172913.9727-5-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9f72d4757cbe4d1ed669192f6d23817c9e437c4b ]
The Qualcomm PCI bridge device (Device ID 0x0110) found in chipsets such as
SM8450 does not set the Command Completed bit unless writes to the Slot
Command register change "Control" bits.
This results in timeouts like below:
pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
Add the device to the Command Completed quirk to mark commands "completed"
immediately unless they change the "Control" bits.
Link: https://lore.kernel.org/r/20220210145003.135907-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0b0b8b897f8e12b2368e868bd7cdc5742d5c5a9 ]
Aardvark hardware supports Multi-MSI and MSI_FLAG_MULTI_PCI_MSI is already
set for the MSI chip. But when allocating MSI interrupt numbers for
Multi-MSI, the numbers need to be properly aligned, otherwise endpoint
devices send MSI interrupt with incorrect numbers.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area().
To ensure that aligned MSI interrupt numbers are used by endpoint devices,
we cannot use Linux virtual irq numbers (as they are random and not
properly aligned). Instead we need to use the aligned hwirq numbers.
This change fixes receiving MSI interrupts on Armada 3720 boards and
allows using NVMe disks which use Multi-MSI feature with 3 interrupts.
Without this NVMe disks freeze booting as linux nvme-core.c is waiting
60s for an interrupt.
Link: https://lore.kernel.org/r/20220110015018.26359-4-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 92c45b63ce22c8898aa41806e8d6692bcd577510 ]
For hardware that only supports 32-bit writes to PCI there is the
possibility of clearing RW1C (write-one-to-clear) bits. A rate-limited
messages was introduced by fb2659230120, but rate-limiting is not the best
choice here. Some devices may not show the warnings they should if another
device has just produced a bunch of warnings. Also, the number of messages
can be a nuisance on devices which are otherwise working fine.
Change the ratelimit to a single warning per bus. This ensures no bus is
'starved' of emitting a warning and also that there isn't a continuous
stream of warnings. It would be preferable to have a warning per device,
but the pci_dev structure is not available here, and a lookup from devfn
would be far too slow.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Fixes: fb2659230120 ("PCI: Warn on possible RW1C corruption for sub-32 bit config writes")
Link: https://lore.kernel.org/r/20200806041455.11070-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 92912b175178c7e895f5e5e9f1e30ac30319162b upstream.
Writes to a Downstream Port's Slot Control register are PCIe hotplug
"commands." If the Port supports Command Completed events, software must
wait for a command to complete before writing to Slot Control again.
pcie_do_write_cmd() sets ctrl->cmd_busy when it writes to Slot Control. If
software notification is enabled, i.e., PCI_EXP_SLTCTL_HPIE and
PCI_EXP_SLTCTL_CCIE are set, ctrl->cmd_busy is cleared by pciehp_isr().
But when software notification is disabled, as it is when pcie_init()
powers off an empty slot, pcie_wait_cmd() uses pcie_poll_cmd() to poll for
command completion, and it neglects to clear ctrl->cmd_busy, which leads to
spurious timeouts:
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x01c0 (issued 2264 msec ago)
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x05c0 (issued 2288 msec ago)
Clear ctrl->cmd_busy in pcie_poll_cmd() when it detects a Command Completed
event (PCI_EXP_SLTSTA_CC).
[bhelgaas: commit log]
Fixes: a5dd4b4b0570 ("PCI: pciehp: Wait for hotplug command completion where necessary")
Link: https://lore.kernel.org/r/20211111054258.7309-1-zhangliguang@linux.alibaba.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215143
Link: https://lore.kernel.org/r/20211126173309.GA12255@wunner.de
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 23584c1ed3e15a6f4bfab8dc5a88d94ab929ee12 upstream.
The Power Fault Detected bit in the Slot Status register differs from
all other hotplug events in that it is sticky: It can only be cleared
after turning off slot power. Per PCIe r5.0, sec. 6.7.1.8:
If a power controller detects a main power fault on the hot-plug slot,
it must automatically set its internal main power fault latch [...].
The main power fault latch is cleared when software turns off power to
the hot-plug slot.
The stickiness used to cause interrupt storms and infinite loops which
were fixed in 2009 by commits 5651c48cfafe ("PCI pciehp: fix power fault
interrupt storm problem") and 99f0169c17f3 ("PCI: pciehp: enable
software notification on empty slots").
Unfortunately in 2020 the infinite loop issue was inadvertently
reintroduced by commit 8edf5332c393 ("PCI: pciehp: Fix MSI interrupt
race"): The hardirq handler pciehp_isr() clears the PFD bit until
pciehp's power_fault_detected flag is set. That happens in the IRQ
thread pciehp_ist(), which never learns of the event because the hardirq
handler is stuck in an infinite loop. Fix by setting the
power_fault_detected flag already in the hardirq handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214989
Link: https://lore.kernel.org/linux-pci/DM8PR11MB5702255A6A92F735D90A4446868B9@DM8PR11MB5702.namprd11.prod.outlook.com
Fixes: 8edf5332c393 ("PCI: pciehp: Fix MSI interrupt race")
Link: https://lore.kernel.org/r/66eaeef31d4997ceea357ad93259f290ededecfd.1637187226.git.lukas@wunner.de
Reported-by: Joseph Bao <joseph.bao@intel.com>
Tested-by: Joseph Bao <joseph.bao@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Stuart Hayes <stuart.w.hayes@gmail.com>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e445375882883f69018aa669b67cbb37ec873406 upstream.
Like other SATA controller chips in the Marvell 88SE91xx series, the
Marvell 88SE9125 has the same DMA requester ID hardware bug that prevents
it from working under IOMMU. Add it to the list of devices that need the
quirk.
Without this patch, device initialization fails with DMA errors:
ata8: softreset failed (1st FIS failed)
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
After applying the patch, the controller can be successfully initialized:
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
ata8.00: ATAPI: PIONEER BD-RW BDR-207M, 1.21, max UDMA/100
ata8.00: configured for UDMA/100
scsi 7:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.21 PQ: 0 ANSI: 5
Link: https://lore.kernel.org/r/YahpKVR+McJVDdkD@work
Reported-by: Sam Bingner <sam@bingner.com>
Tested-by: Sam Bingner <sam@bingner.com>
Tested-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83dbf898a2d45289be875deb580e93050ba67529 upstream.
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1f1 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94185adbfad56815c2c8401e16d81bdb74a79201 upstream.
PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.
That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:
Capabilities: [b0] MSI-X: Enable- Count=67 Masked+
Clear the bit in the error path to restore the reset state.
Fixes: 438553958ba1 ("PCI/MSI: Enable and mask MSI-X early")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tufevoqx.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 661c399a651c11aaf83c45cbfe0b4a1fb7bc3179 upstream.
Current implementation of advk_pcie_link_up() is wrong as it marks also
link disabled or hot reset states as link up.
Fix it by marking link up only to those states which are defined in PCIe
Base specification 3.0, Table 4-14: Link Status Mapped to the LTSSM.
To simplify implementation, Define macros for every LTSSM state which
aardvark hardware can return in CFG_REG register.
Fix also checking for link training according to the same Table 4-14.
Define a new function advk_pcie_link_training() for this purpose.
Link: https://lore.kernel.org/r/20211005180952.6812-13-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Cc: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f76b36d40beee0a13aa8f6aa011df0d7cbbb8a7f upstream.
Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbffac ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.
After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.
(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)
Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.
Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.
Commit 43fc679ced18 ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].
These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582f5 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.
Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.
The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.
According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851daa ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.
Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.
On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.
Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.
The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).
It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)
It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.
[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/
Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4e17d65dafdd3513042d8f00404c9b6068a825c upstream.
Change PCIe Max Payload Size setting in PCIe Device Control register to 512
bytes to align with PCIe Link Initialization sequence as defined in Marvell
Armada 3700 Functional Specification. According to the specification,
maximal Max Payload Size supported by this device is 512 bytes.
Without this kernel prints suspicious line:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 16384, max 512)
With this change it changes to:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 512, max 512)
Link: https://lore.kernel.org/r/20211005180952.6812-3-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 64f160e19e9264a7f6d89c516baae1473b6f8359 upstream.
In commit 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a55, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window configuration")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d1cd163d0de22a4041a6f1aeabcf78f80076539 upstream.
According to PCI Express Base Specifications (rev 4.0, 6.6.1
"Conventional reset"), after fundamental reset a 100ms delay is needed
prior to enabling link training.
Update comment in code to reflect this requirement.
Link: https://lore.kernel.org/r/20201202184659.3795-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0c6a3475b033960e85ae2bf176b14cab0a627d2 upstream.
Move code which belongs to link training (delays and resets) into
advk_pcie_train_link() function, so everything related to link training,
including timings is at one place.
After experiments it can be observed that link training in aardvark
hardware is very sensitive to timings and delays, so it is a good idea to
have this code at the same place as link training calls.
This patch does not change behavior of aardvark initialization.
Link: https://lore.kernel.org/r/20200907111038.5811-6-pali@kernel.org
Tested-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b32c012e4b98f0126aa327be2d1f409963057643 upstream.
Include linux/gpio/consumer.h instead of linux/gpio.h, as is said in the
latter file.
This was reported by kernel test bot when compiling for s390.
drivers/pci/controller/pci-aardvark.c:350:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1074:21: error: implicit declaration of function 'devm_gpiod_get_from_of_node' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1076:14: error: use of undeclared identifier 'GPIOD_OUT_LOW'
Link: https://lore.kernel.org/r/202006211118.LxtENQfl%25lkp@intel.com
Link: https://lore.kernel.org/r/20200907111038.5811-2-pali@kernel.org
Fixes: 5169a9851daa ("PCI: aardvark: Issue PERST via GPIO")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 70e380250c3621c55ff218cbaf2272830d9dbb1d upstream.
When there is no PCIe card connected and advk_pcie_rd_conf() or
advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
root bridge, the aardvark driver throws the following error message:
advk-pcie d0070000.pcie: config read/write timed out
Obviously accessing PCIe registers of disconnected card is not possible.
Extend check in advk_pcie_valid_device() function for validating
availability of PCIe bus. If PCIe link is down, then the device is marked
as Not Found and the driver does not try to access these registers.
This is just an optimization to prevent accessing PCIe registers when card
is disconnected. Trying to access PCIe registers of disconnected card does
not cause any crash, kernel just needs to wait for a timeout. So if card
disappear immediately after checking for PCIe link (before accessing PCIe
registers), it does not cause any problems.
Link: https://lore.kernel.org/r/20200702083036.12230-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1bd5714472cc72e14409f5659b154c765a76c65 upstream.
Most callers of config read do not check for return value. But most of the
ones that do, checks for error indication in 'val' variable.
This patch updates error handling in advk_pcie_rd_conf() function. If PIO
transfer fails then 'val' variable is set to 0xffffffff which indicates
failture.
Link: https://lore.kernel.org/r/20200528162604.GA323482@bjorn-Precision-5520
Link: https://lore.kernel.org/r/20200601130315.18895-1-pali@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96be36dbffacea0aa9e6ec4839583e79faa141a1 upstream.
PCI-E capability macros are already defined in linux/pci_regs.h.
Remove their reimplementation in pcie-aardvark.
Link: https://lore.kernel.org/r/20200430080625.26070-9-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5169a9851daaa2782a7bd2bb83d5b1bd224b2879 upstream.
Add support for issuing PERST via GPIO specified in 'reset-gpios'
property (as described in PCI device tree bindings).
Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
after reboot when PERST is not issued during driver initialization.
If bootloader already enabled link training then issuing PERST has no
effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
not detected. We therefore clear the LINK_TRAINING_EN register before.
It was observed that Compex WLE900VX card needs to be in PERST reset
for at least 10ms if bootloader enabled link training.
Tested on Turris MOX.
Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 43fc679ced18006b12d918d7a8a4af392b7fbfe7 upstream.
Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.
Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.
To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.
Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6964494582f56a3882c2c53b0edbfe99eb32b2e1 upstream.
Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
training and starting link training causes detection issues with some
buggy cards (such as Compex WLE900VX).
Move the code which enables link training immediately before the one
which starts link traning.
This fixes detection issues of Compex WLE900VX card on Turris MOX after
cold boot.
Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org
Fixes: f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready...")
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f4c7d053d7f77cd5c1a1ba7c7ce085ddba13d1d7 upstream.
When configuring pcie reset pin from gpio (e.g. initially set by
u-boot) to pcie function this pin goes low for a brief moment
asserting the PERST# signal. Thus connected device enters fundamental
reset process and link configuration can only begin after a minimal
100ms delay (see [1]).
Because the pin configuration comes from the "default" pinctrl it is
implicitly configured before the probe callback is called:
driver_probe_device()
really_probe()
...
pinctrl_bind_pins() /* Here pin goes from gpio to PCIE reset
function and PERST# is asserted */
...
drv->probe()
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, 6.6.1 Conventional Reset
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3842f5166bf1ef286fe7a39f262b5c9581308366 upstream.
The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
irq_domain_add_linear() also calls of_node_get() to increase refcount,
so irq_domain will not be affected when it is released.
Detected by coccinelle with the following warnings:
./drivers/pci/controller/pci-aardvark.c:826:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 798, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f21082fb20dbfb3e42b769b59ef21c2a7f2c7c1f upstream.
The ION AHCI device pretends that MSI masking isn't a thing, while it
actually implements it and needs MSIs to be unmasked to work. Add a quirk
to that effect.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/r/CALjTZvbzYfBuLB+H=fj2J+9=DxjQ2Uqcy0if_PvmJ-nU-qEgkg@mail.gmail.com
Link: https://lore.kernel.org/r/20211104180130.3825416-3-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2226667a145db2e1f314d7f57fd644fe69863ab9 upstream.
It appears that some devices are lying about their mask capability,
pretending that they don't have it, while they actually do.
The net result is that now that we don't enable MSIs on such
endpoint.
Add a new per-device flag to deal with this. Further patches will
make use of it, sadly.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211104180130.3825416-2-maz@kernel.org
Cc: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3735459037114d31e5acd9894fad9aed104231a0 upstream.
free_msi_irqs() frees the MSI entries before destroying the sysfs entries
which are exposing them. Nothing prevents a concurrent free while a sysfs
file is read and accesses the possibly freed entry.
Move the sysfs release ahead of freeing the entries.
Fixes: 1c51b50c2995 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87sfw5305m.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 464de7e7fff767e87429cd7be09c4f2cb50a6ccb ]
Use dev_dbg() instead of dev_err() in advk_pcie_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Link: https://lore.kernel.org/r/20211005180952.6812-4-kabel@kernel.org
Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 95997723b6402cd6c53e0f9e7ac640ec64eaaff8 upstream.
The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower
8 bits. Fix reading content of this register and add a comment
describing the access to this register.
Link: https://lore.kernel.org/r/20211028185659.20329-4-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4313be1599d397625c14fb7826996813622decf upstream.
MSI domain callback .alloc() (implemented by advk_msi_irq_domain_alloc()
function) should return zero on success, since non-zero value indicates
failure.
When the driver was converted to generic MSI API in commit f21a8b1b6837
("PCI: aardvark: Move to MSI handling using generic MSI support"), it
was converted so that it returns hwirq number.
Fix this.
Link: https://lore.kernel.org/r/20211028185659.20329-3-kabel@kernel.org
Fixes: f21a8b1b6837 ("PCI: aardvark: Move to MSI handling using generic MSI support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
