| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 80dc18a0cba8dea42614f021b20a04354b213d86 upstream.
As per PCIe r6.0, sec 6.6.1, a Downstream Port that supports Link speeds
greater than 5.0 GT/s, software must wait a minimum of 100 ms after Link
training completes before sending a Configuration Request.
Add this delay in dw_pcie_wait_for_link(), after the link is reported as
up. The delay will only be performed in the success case where the link
came up.
DWC glue drivers that have a link up IRQ (drivers that set
use_linkup_irq = true) do not call dw_pcie_wait_for_link(), instead they
perform this delay in their threaded link up IRQ handler.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Link: https://patch.msgid.link/20250625102347.1205584-14-cassel@kernel.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 817f989700fddefa56e5e443e7d138018ca6709d upstream.
Rename PCIE_RESET_CONFIG_DEVICE_WAIT_MS to PCIE_RESET_CONFIG_WAIT_MS.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250625102347.1205584-10-cassel@kernel.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 114b06ee108cabc82b995fbac6672230a9776936 ]
Rockchip controllers can support up to 5.0 GT/s link speed. But the driver
doesn't set the Target Link Speed currently. This may cause failure in
retraining the link to 5.0 GT/s if supported by the endpoint. So set the
Target Link Speed to 5.0 GT/s in the Link Control and Status Register 2.
Fixes: e77f847df54c ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
[mani: fixed whitespace warning, commit message rewording, added fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/0afa6bc47b7f50e2e81b0b47d51c66feb0fb565f.1751322015.git.geraldogabriel@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cbbfe9f683f0f9b6a1da2eaa53b995a4b5961086 ]
Current code uses custom-defined register offsets and bitfields for the
standard PCIe registers. This creates duplication as the PCI header already
defines them. So, switch to using the standard PCIe definitions and drop
the custom ones.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: include bitfield.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/e81700ef4b49f584bc8834bfb07b6d8995fc1f42.1751322015.git.geraldogabriel@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c523fa63ac1d452abeeb4e699560ec3365037f32 ]
IMX8MQ_EP has three 64-bit BAR0/2/4 capable and programmable BARs. For
IMX8MQ_EP, use imx8q_pcie_epc_features (64-bit BARs 0, 2, 4) instead
of imx8m_pcie_epc_features (64-bit BARs 0, 2).
Fixes: 75c2f26da03f ("PCI: imx6: Add i.MX PCIe EP mode support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[bhelgaas: add details in subject]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250708091003.2582846-2-hongxing.zhu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 687aedb73a401addf151c5f60e481e574b4c9ad9 ]
Add support for the i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) PCIe
Endpoint (EP). On the i.MX8Q platforms, the PCI bus addresses differ
from the CPU addresses. However, the DesignWare (DWC) driver already
handles this in the common code.
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-7-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: c523fa63ac1d ("PCI: imx6: Add IMX8MQ_EP third 64-bit BAR in epc_features")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e6ea70690ddd1ffa422423fd0d4523e4dfe4b62 upstream.
According to Documentation/PCI/endpoint/pci-endpoint-cfs.rst, the Endpoint
controller (EPC) should only start the link when userspace writes '1' to
the '/sys/kernel/config/pci_ep/controllers/<EPC>/start' attribute, which
ultimately results in calling imx_pcie_start_link() via
pci_epc_start_store().
To align with the documented behavior, do not start the link automatically
when adding the EP controller.
Fixes: 75c2f26da03f ("PCI: imx6: Add i.MX PCIe EP mode support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded commit subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250709033722.2924372-3-hongxing.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d31eb217425591e100b475fad6360cd3da2073c6 upstream.
apps_reset corresponds to LTSSM_EN in i.MX7, i.MX8MQ, i.MX8MM and i.MX8MP
platforms. Since assertion/de-assertion of apps_reset is done in
imx_pcie_ltssm_enable() and imx_pcie_ltssm_disable(), remove it from
imx_pcie_assert_core_reset() and imx_pcie_deassert_core_reset().
This also fixes a failure in enumerating the PI7C9X2G608GP (hotplug) chip
reliably on i.MX8MM, as reported by Tim.
It should be noted that only i.MX7D, i.MX8MQ, i.MX8MM, and i.MX8MP
platforms have the apps_reset logic, so this change doesn't have any effect
on other platforms.
Fixes: ef61c7d8d032 ("PCI: imx6: Deassert apps_reset in imx_pcie_deassert_core_reset()")
Reported-by: Tim Harvey <tharvey@gateworks.com>
Closes: https://lore.kernel.org/all/CAJ+vNU3ohR2YKTwC4xoYrc1z-neDoH2TTZcMHDy+poj9=jSy+w@mail.gmail.com/
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded commit subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx8mp-venice-gw74xx (i.MX8MP + hotplug capable switch)
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250709033722.2924372-2-hongxing.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 399444a87acdea5d21c218bc8e9b621fea1cd218 upstream.
For IMX8MM_EP and IMX8MP_EP, add fixed 256-byte BAR 4 and reserved BAR 5
in imx8m_pcie_epc_features.
Fixes: 75c2f26da03f ("PCI: imx6: Add i.MX PCIe EP mode support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[bhelgaas: add details in subject]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250708091003.2582846-3-hongxing.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fcc5f586c4edbcc10de23fb9b8c0972a84e945cd ]
Fix the debug message for the PCIE_CORE_INT_UCR interrupt to clearly
indicate "Unexpected Completion" instead of a duplicate "malformed TLP"
message.
Fixes: e77f847df54c ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: added fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/20250607160201.807043-2-18255117159@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 751bec089c4eed486578994abd2c5395f08d0302 ]
Iterating over disabled ports results in of_irq_parse_raw() parsing
the wrong "interrupt-map" entries, as it takes the status of the node
into account.
This became apparent after disabling unused PCIe ports in the Apple
Silicon device trees instead of deleting them.
Switching from for_each_child_of_node_scoped() to
for_each_available_child_of_node_scoped() solves this issue.
Fixes: 1e33888fbe44 ("PCI: apple: Add initial hardware bring-up")
Fixes: a0189fdfb73d ("arm64: dts: apple: t8103: Disable unused PCIe ports")
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/asahi/20230214-apple_dts_pcie_disable_unused-v1-0-5ea0d3ddcde3@jannau.net/
Link: https://lore.kernel.org/asahi/1ea2107a-bb86-8c22-0bbc-82c453ab08ce@linaro.org/
Link: https://patch.msgid.link/20250401091713.2765724-2-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f60b4e06a945f25d463ae065c6e41c6e24faee0a ]
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-6-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Stable-dep-of: 751bec089c4e ("PCI: apple: Set only available ports up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ce0c43e855c7f652b6351110aaaabf9b521debd7 ]
ERR051624: The Controller Without Vaux Cannot Exit L23 Ready Through Beacon
or PERST# De-assertion
When the auxiliary power is not available, the controller cannot exit from
L23 Ready with beacon or PERST# de-assertion when main power is not
removed. So the workaround is to set SS_RW_REG_1[SYS_AUX_PWR_DET] to 1.
This workaround is required irrespective of whether Vaux is supplied to the
link partner or not.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250416081314.3929794-5-hongxing.zhu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7fa9fbf39116b061f8a41cd84f1884c545f322c4 ]
In the success path, we hang onto a reference to the node, so make sure
to grab one. The caller iterator puts our borrowed reference when we
return.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-9-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
one lane
[ Upstream commit af3c6eacce0c464f28fe0e3d365b3860aba07931 ]
As per DWC PCIe registers description 4.30a, section 1.13.43, NUM_OF_LANES
named as PORT_LOGIC_LINK_WIDTH in PCIe DWC driver, is referred to as the
"Predetermined Number of Lanes" in PCIe r6.0, sec 4.2.7.2.1, which explains
the conditions required to enter Polling.Configuration:
Next state is Polling.Configuration after at least 1024 TS1 Ordered Sets
were transmitted, and all Lanes that detected a Receiver during Detect
receive eight consecutive training sequences ...
Otherwise, after a 24 ms timeout the next state is:
Polling.Configuration if,
(i) Any Lane, which detected a Receiver during Detect, received eight
consecutive training sequences ... and a minimum of 1024 TS1 Ordered
Sets are transmitted after receiving one TS1 or TS2 Ordered Set.
And
(ii) At least a predetermined set of Lanes that detected a Receiver
during Detect have detected an exit from Electrical Idle at least
once since entering Polling.Active.
Note: This may prevent one or more bad Receivers or Transmitters
from holding up a valid Link from being configured, and allow for
additional training in Polling.Configuration. The exact set of
predetermined Lanes is implementation specific.
Note: Any Lane that receives eight consecutive TS1 or TS2 Ordered
Sets should have detected an exit from Electrical Idle at least
once since entering Polling.Active.
In a PCIe link supporting multiple lanes, if PORT_LOGIC_LINK_WIDTH is set
to lane width the hardware supports, all lanes that detect a receiver
during the Detect phase must receive eight consecutive training sequences.
Otherwise, LTSSM will not enter Polling.Configuration and link training
will fail.
Therefore, always set PORT_LOGIC_LINK_WIDTH to 1, regardless of the number
of lanes the port actually supports, to make link up more robust. This
setting will not affect the intended link width if all lanes are
functional. Additionally, the link can still be established with at least
one lane if other lanes are faulty.
Co-developed-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
[mani: subject change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: update PCIe spec citation, format quote]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250422103623.462277-1-quic_wenbyao@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 286ed198b899739862456f451eda884558526a9d upstream.
The documentation for the phy_power_off() function explicitly says that it
must be called before phy_exit().
Hence, follow the same rule in rockchip_pcie_phy_deinit().
Fixes: 0e898eb8df4e ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
[mani: commit message change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://patch.msgid.link/20250417142138.1377451-1-didi.debian@cknow.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d9b5d6115532cf90a789ed6afd3f4c70ebbd827 upstream.
rockchip_pcie_link_up() currently has two issues:
1. Value 0x11 of PCIE_L0S_ENTRY corresponds to L0 state, not L0S. So the
naming is wrong from the very beginning.
2. Checking for value 0x11 treats other states like L0S and L1 as link
down, which is wrong.
Hence, remove the PCIE_L0S_ENTRY check and also its definition. This allows
adding ASPM support in the successive commits.
Fixes: 0e898eb8df4e ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/1744850111-236269-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 810276362bad172d063d1f6be1cc2cb425b90103 upstream.
While dw_pcie_ep_set_msix() writes the Table Size field correctly (N-1),
the calculation of the PBA offset is wrong because it calculates space for
(N-1) entries instead of N.
This results in the following QEMU error when using PCI passthrough on a
device which relies on the PCI endpoint subsystem:
failed to add PCI capability 0x11[0x50]@0xb0: table & pba overlap, or they don't fit in BARs, or don't align
Fix the calculation of PBA offset in the MSI-X capability.
[bhelgaas: more specific subject and commit log]
Fixes: 83153d9f36e2 ("PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250514074313.283156-9-cassel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c8bcb01352a86bc5592403904109c22b66bd916e upstream.
While cdns_pcie_ep_set_msix() writes the Table Size field correctly (N-1),
the calculation of the PBA offset is wrong because it calculates space for
(N-1) entries instead of N.
This results in the following QEMU error when using PCI passthrough on a
device which relies on the PCI endpoint subsystem:
failed to add PCI capability 0x11[0x50]@0xb0: table & pba overlap, or they don't fit in BARs, or don't align
Fix the calculation of PBA offset in the MSI-X capability.
[bhelgaas: more specific subject and commit log]
Fixes: 3ef5d16f50f8 ("PCI: cadence: Add MSI-X support to Endpoint driver")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250514074313.283156-10-cassel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7334364f9de79a9a236dd0243ba574b8d2876e89 ]
We're allowed to sleep here, so tell the GPIO core by using
gpiod_set_value_cansleep instead of gpiod_set_value.
Fixes: 1e33888fbe44 ("PCI: apple: Add initial hardware bring-up")
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-12-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8805f32a96d3b97cef07999fa6f52112678f7e65 ]
If the call to pci_host_probe() in cdns_pcie_host_setup() fails, PM
runtime count is decremented in the error path using pm_runtime_put_sync().
But the runtime count is not incremented by this driver, but only by the
callers (cdns_plat_pcie_probe/j721e_pcie_probe). And the callers also
decrement the runtime PM count in their error path. So this leads to the
below warning from the PM core:
"runtime PM usage count underflow!"
So fix it by getting rid of pm_runtime_put_sync() in the error path and
directly return the errno.
Fixes: 49e427e6bdd1 ("Merge branch 'pci/host-probe-refactor'")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250419133058.162048-1-18255117159@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b584ab12d59f646b9254b2b16ff197d612fd4935 ]
On rcar-gen4, the ep BAR4 has a fixed size of 256B. Document this
constraint in the epc features of the platform.
Fixes: e311b3834dfa ("PCI: rcar-gen4: Add endpoint mode support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250328-rcar-gen4-bar4-v1-1-10bb6ce9ee7f@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2294059118c550464dd8906286324d90c33b152b ]
Then the brcmstb PCIe driver and MIP MSI-X interrupt controller
drivers are built as modules there could be a race in probing.
To avoid this, add a softdep to MIP driver to guarantee that
MIP driver will be load first.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-5-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 25a98c727015638baffcfa236e3f37b70cedcf87 ]
The BCM2712 memory map can support up to 64GB of system memory, thus
expand the inbound window size in calculation helper function.
The change is safe for the currently supported SoCs that have smaller
inbound window sizes.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-7-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8f4a489b370e6612700aa16b9e4373b2d85d7503 ]
The msg_res region translates writes into PCIe Message TLPs. Previously we
mapped this region using atu.cpu_addr, the input address programmed into
the ATU.
"cpu_addr" is a misnomer because when a bus fabric translates addresses
between the CPU and the ATU, the ATU input address is different from the
CPU address. A future patch will rename "cpu_addr" and correct the value
to be the ATU input address instead of the CPU physical address.
Map the msg_res region before writing to it using the msg_res resource
start, a CPU physical address.
Link: https://lore.kernel.org/r/20250315201548.858189-2-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c4d5aadf5df31ea0ac025980670eee9beaf466b ]
MSI remapping bypass (directly configuring MSI entries for devices on the
VMD bus) won't work under Xen, as Xen is not aware of devices in such bus,
and hence cannot configure the entries using the pIRQ interface in the PV
case, and in the PVH case traps won't be setup for MSI entries for such
devices.
Until Xen is aware of devices in the VMD bus prevent the
VMD_FEAT_CAN_BYPASS_MSI_REMAP capability from being used when running as
any kind of Xen guest.
The MSI remapping bypass is an optional feature of VMD bridges, and hence
when running under Xen it will be masked and devices will be forced to
redirect its interrupts from the VMD bridge. That mode of operation must
always be supported by VMD bridges and works when Xen is not aware of
devices behind the VMD bridge.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-ID: <20250219092059.90850-3-roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3e1dccba0a0833fc9a05fb838ebeb6ea4ca0e1a ]
Most systems' PCIe outbound map windows have non-zero physical addresses,
but the possibility of encountering zero increased after following commit
("PCI: dwc: Use parent_bus_offset").
'ep->outbound_addr[n]', representing 'parent_bus_address', might be 0 on
some hardware, which trims high address bits through bus fabric before
sending to the PCIe controller.
Replace the iteration logic with 'for_each_set_bit()' to ensure only
allocated map windows are iterated when determining the ATU index from a
given address.
Link: https://lore.kernel.org/r/20250315201548.858189-12-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d66b5b336245b91681c2042e7eedf63ef7c2f6db upstream.
Commit e49ad667815d ("PCI: j721e: Add TI J784S4 PCIe configuration")
assigned the value of .linkdown_irq_regfield for the J784S4 SoC as the
"LINK_DOWN" macro corresponding to BIT(1), and as a result, the Link
Down interrupts on J784S4 SoC are missed.
According to the Technical Reference Manual and Register Documentation
for the J784S4 SoC[1], BIT(1) corresponds to "ENABLE_SYS_EN_PCIE_DPA_1",
which is not the correct field for the link-state interrupt. Instead, it
is BIT(10) of the "PCIE_INTD_ENABLE_REG_SYS_2" register that corresponds
to the link-state field named as "ENABLE_SYS_EN_PCIE_LINK_STATE".
Thus, set .linkdown_irq_regfield to the macro "J7200_LINK_DOWN", which
expands to BIT(10) and was first defined for the J7200 SoC. Other SoCs
already reuse this macro since it accurately represents the "link-state"
field in their respective "PCIE_INTD_ENABLE_REG_SYS_2" register.
1: https://www.ti.com/lit/zip/spruj52
Fixes: e49ad667815d ("PCI: j721e: Add TI J784S4 PCIe configuration")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, add a missing .linkdown_irq_regfield member
set to the J7200_LINK_DOWN macro to struct j7200_pcie_ep_data]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250305132018.2260771-1-s-vadapalli@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2df181e1aea4628a8fd257f866026625d0519627 upstream.
A call to of_parse_phandle() is incrementing the refcount, and as such,
the of_node_put() must be called when the reference is no longer needed.
Thus, refactor the existing code and add a missing of_node_put() call
following the check to ensure that "msi_np" matches "pcie->np" and after
MSI initialization, but only if the MSI support is enabled system-wide.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 40ca1bf580ef ("PCI: brcmstb: Add MSI support")
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250122222955.1752778-1-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 18056a48669a040bef491e63b25896561ee14d90 ]
The access to the PCI config space via pci_ops::read and pci_ops::write is
a low-level hardware access. The functions can be accessed with disabled
interrupts even on PREEMPT_RT. The pci_lock is a raw_spinlock_t for this
purpose.
A spinlock_t becomes a sleeping lock on PREEMPT_RT, so it cannot be
acquired with disabled interrupts. The vmd_dev::cfg_lock is accessed in
the same context as the pci_lock.
Make vmd_dev::cfg_lock a raw_spinlock_t type so it can be used with
interrupts disabled.
This was reported as:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
Call Trace:
rt_spin_lock+0x4e/0x130
vmd_pci_read+0x8d/0x100 [vmd]
pci_user_read_config_byte+0x6f/0xe0
pci_read_config+0xfe/0x290
sysfs_kf_bin_read+0x68/0x90
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Tested-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Acked-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
[bigeasy: reword commit message]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Link: https://lore.kernel.org/r/20250218080830.ufw3IgyX@linutronix.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: add back report info from
https://lore.kernel.org/lkml/20241218115951.83062-1-ryotkkr98@gmail.com/]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 20bbb083bbc9d3f8db390f2e35e168f1b23dae8a ]
Move PCI_VENDOR_ID_ROCKCHIP from pci_endpoint_test.c to pci_ids.h and
reuse it in pcie-rockchip-host.c.
Link: https://lore.kernel.org/r/20250218092120.2322784-2-cassel@kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b36fb50701619efca5f5450b355d42575cf532ed ]
If an error occurs after a successful phy_init() call, then phy_exit()
should be called.
Add the missing call, as already done in the remove function.
Fixes: bbd11bddb398 ("PCI: hisi: Add HiSilicon STB SoC PCIe controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[kwilczynski: remove unnecessary hipcie->phy NULL check from
histb_pcie_probe() and squash a patch that removes similar NULL
check for hipcie-phy from histb_pcie_remove() from
https://lore.kernel.org/linux-pci/c369b5d25e17a44984ae5a889ccc28a59a0737f7.1742058005.git.christophe.jaillet@wanadoo.fr]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/8301fc15cdea5d2dac21f57613e8e6922fb1ad95.1740854531.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8189aa56dbed0bfb46b7b30d4d231f57ab17b3f4 ]
If the bitmap or memory allocations fail, then dw_pcie_ep_init_registers()
will incorrectly return a success.
Return -ENOMEM instead.
Fixes: 869bc5253406 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/36dcb6fc-f292-4dd5-bd45-a8c6f9dc3df7@stanley.mountain
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 57b0302240741e73fe51f88404b3866e0d2933ad ]
The IRQ domain allocated for the PCIe controller is not freed if
resource_list_first_type() returns NULL, leading to a resource leak.
This fix ensures properly cleaning up the allocated IRQ domain in
the error path.
Fixes: 49e427e6bdd1 ("Merge branch 'pci/host-probe-refactor'")
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: added missing Fixes: tag, refactored to use one of the goto labels]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250224155025.782179-2-thippeswamy.havalige@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b7de1b60ecab2f7b6f05d8116e93228a0bbb8563 ]
The platform supports enabling and disabling regulators only on
ports below the Root Complex.
Thus, we need to verify this both when adding and removing the bus,
otherwise regulators may be disabled prematurely when a bus further
down the topology is removed.
Fixes: 9e6be018b263 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-6-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3651ad5249c51cf7eee078e12612557040a6bdb4 ]
If the regulator_bulk_get() returns an error and no regulators
are created, we need to set their number to zero.
If we don't do this and the PCIe link up fails, a call to the
regulator_bulk_free() will result in a kernel panic.
While at it, print the error value, as we cannot return an error
upwards as the kernel will WARN() on an error from add_bus().
Fixes: 9e6be018b263 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-5-james.quinlan@broadcom.com
[kwilczynski: commit log, use comma in the message to match style with
other similar messages]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0c97321e11e0e9e18546f828492758f6aaecec59 ]
The driver has been mistakenly writing to a read-only (RO)
configuration space register (PCI_EXP_LNKCAP) to change the
PCIe link capability.
Although harmless in this case, the proper write destination
is an internal register that is reflected by PCI_EXP_LNKCAP.
Thus, fix the brcm_pcie_set_gen() function to correctly update
the link capability.
Fixes: c0452137034b ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-3-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72d36589c6b7bef6b30eb99fcb7082f72faca37f ]
When the user elects to limit the PCIe generation via the appropriate
devicetree property, apply the settings before the PCIe link up, not
after.
Fixes: c0452137034b ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-2-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3ac47fbf4f6e8c3a7c3855fac68cc3246f90f850 ]
Per the Cadence's "PCIe Controller IP for AX14" user guide, Version
1.04, Section 9.1.7.1, "AXI Subordinate to PCIe Address Translation
Registers", Table 9.4, the bit 16 of the AXI Subordinate Address
(axi_s_awaddr) when set corresponds to MSG with data, and when not set,
to MSG without data.
However, the driver is currently doing the opposite and due to this,
the INTx is never received on the host.
So, fix the driver to reflect the documentation and also make INTx work.
Fixes: 37dddf14f1ae ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Hans Zhang <hans.zhang@cixtech.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214165724.184599-1-18255117159@163.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3708acbd5f169ebafe1faa519cb28adc56295546 upstream.
In commit 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
Fixes: 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Link: https://lore.kernel.org/r/20241213143301.4158431-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 33a6938e0c3373f2d11f92d098f337668cd64fdd upstream.
The "DesignWare Cores PCI Express Controller Register Descriptions,
Version 4.60a", section "1.21.70 IATU_LWR_TARGET_ADDR_OFF_INBOUND_i",
fields LWR_TARGET_RW and LWR_TARGET_HW both state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
If we do not write the BAR_MASK before writing the iATU registers, we are
relying the reset value of the BAR_MASK being larger than the requested
BAR size (which is supplied in the struct pci_epf_bar which is passed to
pci_epc_set_bar()). The reset value of the BAR_MASK is SoC dependent.
Thus, if the struct pci_epf_bar requests a BAR size that is larger than the
reset value of the BAR_MASK, the iATU will try to write to read-only bits,
which will cause the iATU to end up redirecting to a physical address that
is different from the address that was intended.
Thus, we should always write the iATU registers after writing the BAR_MASK.
Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20241213143301.4158431-9-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mode
[ Upstream commit 1390a33b3d04fdf6ba4e3e7082107a12027fc188 ]
On Microchip PolarFire SoC the PCIe Root Port can be behind one of three
general purpose Fabric Interface Controller (FIC) buses that encapsulates
an AXI-S bus. Depending on which FIC(s) the Root Port is connected through
to CPU space, and what address translation is done by that FIC, the Root
Port driver's inbound address translation may vary.
For all current supported designs and all future expected designs, inbound
address translation done by a FIC on PolarFire SoC varies depending on
whether PolarFire SoC is operating in coherent DMA mode or noncoherent DMA
mode.
The setup of the outbound address translation tables in the Root Port
driver only needs to handle these two cases.
Setup the inbound address translation tables to one of two address
translations, depending on whether the Root Port is being used with
coherent DMA or noncoherent DMA.
Link: https://lore.kernel.org/r/20241011140043.1250030-3-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f941 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
[bhelgaas: adapt for ac7f53b7e728 ("PCI: microchip: Add support for using
either Root Port 1 or 2")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ac7f53b7e7283fee35ad12de8359f20989a47eb5 ]
The PCI host controller on PolarFire SoC has multiple Root Port instances,
each with their own bridge and ctrl address spaces. The original binding
has an "apb" register region, and it is expected to be set to the base
address of the Root Complex register space. Some defines in the Linux
driver were used to compute the addresses of the bridge and ctrl address
ranges corresponding to Root Port instance 1. Some customers want to use
Root Port instance 2 however, which requires changing the defines in the
driver, which is clearly not a portable solution.
The binding has been changed from a single register region to a pair,
corresponding to the bridge and ctrl regions respectively, so modify the
driver to read these regions directly from the devicetree rather than
compute them from the base address of the abp region.
To maintain backwards compatibility with the existing binding, the driver
retains code to handle the "abp" reg and computes the base address of the
bridge and ctrl regions using the defines if it is present. reg-names has
always been a required property, so this is safe to do.
Link: https://lore.kernel.org/r/20241107-surrender-brisket-287d563a5de1@spud
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[bhelgaas: Capitalize PCIe spec terms]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stable-dep-of: 1390a33b3d04 ("PCI: microchip: Set inbound address translation for coherent or non-coherent mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 86a016e278b78cc2281edd4ffaddbc011c87a593 ]
On the i.MX8QM, PCIe link can't be re-established again in
dw_pcie_resume_noirq(), if the LTSSM_EN bit is not cleared
properly in dw_pcie_suspend_noirq().
So, add dw_pcie_stop_link() to dw_pcie_suspend_noirq() to fix
this issue and to align the suspend/resume functions since there
is dw_pcie_start_link() in dw_pcie_resume_noirq() already.
Fixes: 4774faf854f5 ("PCI: dwc: Implement generic suspend/resume functionality")
Link: https://lore.kernel.org/r/20241210081557.163555-2-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f0639013d340580b72df95d012a93f35eeb0da64 ]
4581403f6792 ("PCI: qcom: Enumerate endpoints based on Link up event in
'global_irq' interrupt") added the Link Up-based enumeration support, but
did not update the ICC/OPP vote once link is up. Before that, the update
happened during probe and the endpoints may or may not be enumerated at
that time, so the ICC/OPP vote was not guaranteed to be accurate.
With Link Up-based enumeration support, the driver can request the accurate
vote based on the PCIe link.
Call qcom_pcie_icc_opp_update() in qcom_pcie_global_irq_thread() after
enumerating the endpoints.
Fixes: 4581403f6792 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-3-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 93d883f89063744a92006fc356b1c767eb62d950 ]
Ensure the *_enable_ref_clk() function is symmetric by addressing missing
disable parts on some platforms.
Fixes: d0a75c791f98 ("PCI: imx6: Factor out ref clock disable to match enable")
Link: https://lore.kernel.org/r/20241126075702.4099164-7-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ef61c7d8d032adb467f99d03ccfaa293b417ac75 ]
Since the apps_reset is asserted in imx_pcie_assert_core_reset(), it should
be deasserted in imx_pcie_deassert_core_reset().
Fixes: 9b3fe6796d7c ("PCI: imx6: Add code to support i.MX7D")
Link: https://lore.kernel.org/r/20241126075702.4099164-6-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f068ffdd034c93f0c768acdc87d4d2d7023c1379 ]
The i.MX7D only has one PCIe controller, so controller_id should always be
0. The previous code is incorrect although yielding the correct result.
Fix by removing "IMX7D" from the switch case branch.
Fixes: 2d8ed461dbc9 ("PCI: imx6: Add support for i.MX8MQ")
Link: https://lore.kernel.org/r/20241126075702.4099164-5-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit de22e20589b79f35f92543119c33051f8179dba0 ]
Pass PHY_MODE_PCIE_EP if the PCI controller operates in Endpoint (EP) mode,
and fix the Root Complex (RC) mode being hardcoded using a drvdata mode
check.
Fixes: 8026f2d8e8a9 ("PCI: imx6: Call common PHY API to set mode, speed, and submode")
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-6-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2d2da5a4c1b4509f6f7e5a8db015cd420144beb4 ]
The rcar_pcie_parse_outbound_ranges() uses the devm_request_mem_region()
macro to request a needed resource. A string variable that lives on the
stack is then used to store a dynamically computed resource name, which
is then passed on as one of the macro arguments. This can lead to
undefined behavior.
Depending on the current contents of the memory, the manifestations of
errors may vary. One possible output may be as follows:
$ cat /proc/iomem
30000000-37ffffff :
38000000-3fffffff :
Sometimes, garbage may appear after the colon.
In very rare cases, if no NULL-terminator is found in memory, the system
might crash because the string iterator will overrun which can lead to
access of unmapped memory above the stack.
Thus, fix this by replacing outbound_name with the name of the previously
requested resource. With the changes applied, the output will be as
follows:
$ cat /proc/iomem
30000000-37ffffff : memory2
38000000-3fffffff : memory3
Fixes: 2a6d0d63d999 ("PCI: rcar: Add endpoint mode support")
Link: https://lore.kernel.org/r/tencent_DBDCC19D60F361119E76919ADAB25EC13C06@qq.com
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: King Dix <kingdix10@qq.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
