| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Convert mvneta to use the mac_select_interface rather than using
phylink_set_pcs(). The intention here is to unify the approach for
PCS and eventually remove phylink_set_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-order the mvneta initialisation to move devm based resources and
easy setup earlier in the probe function. The primary reason for this
is to allow us to switch the driver to use phylink's mac_select_pcs()
callback.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for downstream SFP cages for AR8031 and AR8033. This is
primarily intended for fiber modules or direct-attach cables, however
copper modules which work in 1000Base-X mode may also function. Such
modules are allowed with a warning.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously this driver always forced the copper page to be selected,
however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page
needs to be selected. Set the appropriate mode based on the hardware
mode_cfg strap selection.
Enable the appropriate interrupt bits to detect fiber-side link up
or down events.
Update config_aneg and read_status methods to use the appropriate
Clause 37 calls when fiber mode is in use.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fix to select the copper page on AR8031 was being done in the probe
function rather than config_init, so it would not be redone after resume
from suspend. Move this to config_init so it is always redone when
needed.
Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon error the ieee802154_xmit_complete() helper is not called. Only
ieee802154_wake_queue() is called manually. We then leak the skb
structure.
Free the skb structure upon error before returning.
Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-5-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
Upon error the ieee802154_xmit_complete() helper is not called. Only
ieee802154_wake_queue() is called manually. In the Tx case we then leak
the skb structure.
Free the skb structure upon error before returning when appropriate.
As the 'is_tx = 0' cannot be moved in the complete handler because of a
possible race between the delay in switching to STATE_RX_AACK_ON and a
new interrupt, we introduce an intermediate 'was_tx' boolean just for
this purpose.
There is no Fixes tag applying here, many changes have been made on this
area and the issue kind of always existed.
Suggested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
These periods are expressed in time units (microseconds) while 40 and 12
are the number of symbol durations these periods will last. We need to
multiply them both with phy->symbol_duration in order to get these
values in microseconds.
Fixes: 8c6ad9cc5157 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
Drivers are expected to set the PHY current_channel and current_page
according to their default state. The hwsim driver is advertising being
configured on channel 13 by default but that is not reflected in its own
internal pib structure. In order to ensure that this driver consider the
current channel as being 13 internally, we at least need to set the
pib->channel field to 13.
Fixes: f25da51fdc38 ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[stefan@datenfreihafen.org: fixed assigment from page to channel]
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-2-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
Update comments to only use kdoc style comments, starting with '/**',
for kdoc.
Flagged by ./scripts/kernel-doc
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220126090803.5582-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use GFP_ATOMIC when allocating pages out of the hotpath,
continue to use GFP_KERNEL when allocating pages during setup.
GFP_KERNEL will allow blocking which allows it to succeed
more often in a low memory enviornment but in the hotpath we do
not want to allow the allocation to block.
Fixes: f5cedc84a30d2 ("gve: Add transmit and receive support")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Link: https://lore.kernel.org/r/20220126003843.3584521-1-awogbemila@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add ability of setting mac address in DT for cortina ethernet driver.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220125210811.54350-1-clabbe@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/net/ethernet/netronome/nfp/flower/tunnel_conf.c:359:25: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum1_kvdl.c:229:24: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert dpaa2-mac to use the mac_select_pcs() interface rather than
using phylink_set_pcs(). The intention here is to unify the approach
for PCS and eventually to remove phylink_set_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0ebecb2644c8 ("net: mdio: Add helper functions for accessing
MDIO devices") added support for mdiodev accessor operations that
neatly wrap the mdiobus accessor operations. Since we are dealing with
a mdio device here, update the driver to use mdiodev_write().
Tested-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert axienet to use the phylink_pcs layer, resulting in it no longer
being a legacy driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function lan966x_mac_wait_for_completion is used to poll the status
of the MAC table using the function readx_poll_timeout. The problem with
this function is that is called also from atomic context. Therefore
update the function to use readx_poll_timeout_atomic.
Fixes: e18aba8941b40b ("net: lan966x: add mactable support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On lan966x, when injecting a frame it was polling the register
QS_INJ_STATUS to see if it can continue with the injection of the frame.
The problem was that it was using readx_poll_timeout which could sleep
in atomic context.
This patch fixes this issue by using readx_poll_timeout_atomic.
Fixes: d28d6d2e37d10d ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev->dev_addr is const now.
Compile tested rpc_defconfig w/ GCC 8.5.
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev->dev_addr is const now.
Compile tested rpc_defconfig w/ GCC 8.5.
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev->dev_addr is const now.
Compile tested rpc_defconfig w/ GCC 8.5.
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev->dev_addr is const now.
Compile tested bigsur_defconfig and sb1250_swarm_defconfig.
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev->dev_addr is const now.
Maintain the questionable offsetting in ndo_set_mac_address.
Compile tested holly_defconfig and mpc7448_hpc2_defconfig.
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver casts off the const and writes directly to netdev->dev_addr.
This will result in a MAC address tree corruption and a warning.
Compile tested ppc6xx_defconfig.
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Multi-host environment, when the PHC is updated by one host,
an async message from firmware will be sent to other hosts.
Re-initialize the timecounter when the driver receives this
async message.
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The adjusted time is set in the PHC in RTC mode. We also need to
update the snapshots ptp->current_time and ptp->old_time when the
time is adjusted.
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for RTC mode if it is supported by firmware. In RTC
mode, the PHC is set to the 64-bit clock. Because the legacy interface
is 48-bit, the driver still has to keep track of the upper 16 bits and
handle the rollover.
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Making the ptp free and timecounter initialization code into separate
functions so that later patches can use them.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The main changes are PTP support for RTC, additional NVM error codes,
backing store v2 firmware APIs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert stmmac to use the mac_select_pcs() interface rather than using
phylink_set_pcs(). The intention here is to unify the approach for PCS
and eventually to remove phylink_set_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert stmmac to use phylink_generic_validate() now that we have the
MAC capabilities and supported interfaces filled in, and we have the
PCS validation handled via the PCS operations.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Phylink will use PCS polling whenever the PCS's poll member is set, so
setting phylink_config.pcs_poll as well is redundant.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
stmmac explicitly calls the xpcs driver to validate the ethtool
linkmodes. This is no longer necessary as phylink now supports
validation through a PCS method. Convert both drivers to use this
new mechanism.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fill in phylink's supported_interfaces bitmap with the PHY interface
modes which can be used to talk to the PHY.
We indicate that the PHY interface mode passed in platform data is
always supported, as this is the initial mode passed into phylink.
When there is no PCS specified, we assume that this is the only mode
that is supported - indeed, the driver appears not to support dynamic
switching of interface types at present.
When a xpcs is present, it defines the PHY interface modes that the
stmmac driver can support. Request the supported interfaces from the
xpcs driver, and pass them to phylink.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the MAC speed, duplex and pause capabilities to the phylink_config
structure, and switch stmmac_validate() to use phylink_get_linkmodes()
to generate the mask of supported ethtool link modes.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a function to the xpcs driver to retrieve the supported PHY
interface modes, which can be used by drivers to fill in phylink's
supported_interfaces mask.
We validate the interface bit index to ensure that it fits within the
bitmap as xpcs lists PHY_INTERFACE_MODE_MAX in an entry.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Transceiver module reset through 'rst' field in PMAOS register is not
supported on RJ45 ports, so module reset should be rejected.
Therefore, before trying to access this field, validate the port module
type that was queried during initialization and return an error to user
space in case the port module type is RJ45 (twisted pair).
Output example:
# ethtool --reset swp11 phy
ETHTOOL_RESET 0x40
Cannot issue ETHTOOL_RESET: Invalid argument
$ dmesg
mlxsw_spectrum 0000:03:00.0 swp11: Reset module is not supported on port module type
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PMMP (Port Module Memory Map Properties) and MCION (Management Cable IO
and Notifications) registers are not supported on RJ45 ports, so setting
and getting power mode should be rejected.
Therefore, before trying to access those registers, validate the port
module type that was queried during initialization and return an error
to user space in case the port module type is RJ45 (twisted pair).
Set output example:
# ethtool --set-module swp1 power-mode-policy auto
netlink error: mlxsw_core: Power mode is not supported on port module type
netlink error: Invalid argument
Get output example:
$ ethtool --show-module swp11
netlink error: mlxsw_core: Power mode is not supported on port module type
netlink error: Invalid argument
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MCIA (Management Cable Info Access) register is not supported on RJ45
ports, so getting module EEPROM should be rejected.
Therefore, before trying to access this register, validate the port
module type that was queried during initialization and return an error
to user space in case the port module type is RJ45 (twisted pair).
Examples for output when trying to get EEPROM module:
Using netlink:
# ethtool -m swp1
netlink error: mlxsw_core: EEPROM is not equipped on port module type
netlink error: Invalid argument
Using IOCTL:
# ethtool -m swp1
Cannot get module EEPROM information: Invalid argument
$ dmesg
mlxsw_spectrum 0000:03:00.0 swp1: EEPROM is not equipped on port module type
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query and store port module's type during initialization so that it
could be later used to determine if certain configurations are allowed
based on the type.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the Port Module Type Mapping (PMTP) register. It will be used by
subsequent patches to query port module types and forbid certain
configurations based on the port module's type.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of a process for supporting a new system with RJ45 connectors,
100BaseT and 1000BaseT link modes need to be supported.
Add support for these two link modes by adding the two corresponding
bits in PTYS (Port Type and Speed) register.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patches will forbid querying the port module's EEPROM info when
its type is RJ45 as in this case no transceiver module can ever be
connected to the port.
Add netdev argument to mlxsw_env_get_module_info() so it could be used
to print an error to the kernel log via netdev_err().
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of modules can be resolved from the first argument, so do not
pass it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the 'err' variable and simply return.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Copy scattered mac address octets into an array then eth_hw_addr_set().
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20220125144007.64407-1-tsbogend@alpha.franken.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Variable new_csr6 is being initialized with a value that is never
read, it is being re-assigned later on. The assignment is redundant
and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220123183440.112495-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since some interrupt states may be cleared by hardware, the driver
may receive an empty interrupt. Currently, the VF driver directly
disables the vector0 interrupt in this case. As a result, the VF
is unavailable. Therefore, the vector0 interrupt should be enabled
in this case.
Fixes: b90fcc5bd904 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
