| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The smsc95xx driver was forwarding the trailing fcs on received frames
up the stack leading to confusion in tcpdump.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comments describing the rx/tx headers used a combination of zero-
and 1-based indexing, leading to confusion.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct net_device trans_start field is a hot spot on SMP and high performance
devices, particularly multi queues ones, because every transmitter dirties
it. Is main use is tx watchdog and bonding alive checks.
But as most devices dont use NETIF_F_LLTX, we have to lock
a netdev_queue before calling their ndo_start_xmit(). So it makes
sense to move trans_start from net_device to netdev_queue. Its update
will occur on a already present (and in exclusive state) cache line, for
free.
We can do this transition smoothly. An old driver continue to
update dev->trans_start, while an updated one updates txq->trans_start.
Further patches could also put tx_bytes/tx_packets counters in
netdev_queue to avoid dirtying dev->stats (vlan device comes to mind)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Napi structures are being created each time we open a port, but when
the port is closed the napi structure is only disabled but not removed.
This bug caused hang while removing the driver.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using bnx2 in a high transmit load, bnx2_tx_int() cost is pretty high.
There are two reasons.
One is an expensive call to bnx2_get_hw_tx_cons(bnapi) for each freed skb
One is cpu stalls when accessing skb_is_gso(skb) / skb_shinfo(skb)->nr_frags
because of two cache line misses.
(One to get skb->end/head to compute skb_shinfo(skb),
one to get is_gso/nr_frags)
This patch :
1) avoids calling bnx2_get_hw_tx_cons(bnapi) too many times.
2) makes bnx2_start_xmit() cache is_gso & nr_frags into sw_tx_bd descriptor.
This uses a litle bit more ram (256 longs per device on x86), but helps a lot.
3) uses a prefetch(&skb->end) to speedup dev_kfree_skb(), bringing
cache line that will be needed in skb_release_data()
result is 5 % bandwidth increase in benchmarks, involving UDP or TCP receive
& transmits, when a cpu is dedicated to ksoftirqd for bnx2.
bnx2_tx_int going from 3.33 % cpu to 0.5 % cpu in oprofile
Note : skb_dma_unmap() still very expensive but this is for another patch,
not related to bnx2 (2.9 % of cpu, while it does nothing on x86_32)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev->dev_addr changed from being an array to being a pointer, so we
should not take its address for memcpy().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds FCoE related statistics to 82599, including number Rx-ed and Tx-ed
FCoE packets, number of Rx-ed and Tx-ed FCoE packets in dwords, number of bad
Fiber Channel CRCs detected in FCoE packets, and number of FCoE packets dropped
on the Rx side.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements the FCoE Rx side offload feature in ixgbe_main.c
to 82599 using the Rx offload infrastructure code added in the previous
patch. The large receive offload by Direct Data Placement (DDP) for
FCoE is achieved by implementing the ndo_fcoe_ddp_setup and ndo_fcoe_ddp_done
in net_device_ops via netdev. It is up to the ULD, i.e., fcoe and libfc
to query and setup large receive offload accordingly through the corresponding
netdev upon creating fcoe instances.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds infrastructure code for FCoE Rx side offload feature to
82599, which provides large receive offload for FCoE by Direct
Data Placement (DDP). The ixgbe_fcoe_ddp_get() and ixgbe_fcoe_ddp_put()
pair corresponds to the netdev support to FCoE by the function pointers
provided in net_device_ops as ndo_fcoe_ddp_setup and ndo_fcoe_ddp_done.
The implementation of these in ixgbe is shown in the next patch.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements the FCoE Tx side offload features in ixgbe_main.c
to 82599 using the Tx offload infrastructure code added in the previous
patch. This is achieved by the calling the FCoE Sequence Offload (FSO)
function ixgbe_fso() on the transmit path of ixgbe.
This patch also includes an EEPROM check to make sure the NIC we're loading
on is an offload-enabled SKU.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds infrastructure code for FCoE Tx side offload feature to
82599, including Fiber Channel CRC calculation, auto insertion of
the start of frame (SOF) and end of frame (EOF) of FCoE packets,
and large send by FCoE Sequence Offload (FSO).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the FCoE feature code ixgbe_fcoe.c to 82599. For a start, this patch
only adds ixgbe_configure_fcoe() to configure related register for FCoE to 82599.
In patches that follow, I will be adding more functions to ixgbe_fcoe.c to add
support of FCoE offload features to 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the FCoE feature header ixgbe_fcoe.h to 82599. This header includes
the defines and structures required by the ixgbe driver to support various
offload features in 82599 for Fiber Channel over Ethernet (FCoE). These offloads
features include Fiber Channel CRC calculation, FCoE SOF/EOF auto insertion,
FCoE Sequence Offload (FSO) for large send, and Direct Data Placement (DDP)
for large receive.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds FCoE related register defines to 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPC_MULTIPLATFORM was killed in commit 28794d3 but this stale occurrence was
hiding the mv643xx_eth driver in some cases (e.g. Pegasos II)
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i386 allmodconfig:
drivers/net/82596.c: In function 'init_rx_bufs':
drivers/net/82596.c:544: warning: cast to pointer from integer of different size
drivers/net/82596.c:545: warning: cast to pointer from integer of different size
drivers/net/82596.c:548: warning: cast to pointer from integer of different size
drivers/net/82596.c:557: warning: cast to pointer from integer of different size
drivers/net/82596.c:565: warning: cast to pointer from integer of different size
drivers/net/82596.c:569: warning: cast to pointer from integer of different size
drivers/net/82596.c:575: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'rebuild_rx_bufs':
drivers/net/82596.c:606: warning: cast to pointer from integer of different size
drivers/net/82596.c:608: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'init_i596_mem':
drivers/net/82596.c:680: warning: cast to pointer from integer of different size
drivers/net/82596.c:681: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'i596_rx':
drivers/net/82596.c:818: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'i596_add_cmd':
drivers/net/82596.c:975: warning: cast to pointer from integer of different size
drivers/net/82596.c:979: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'i596_start_xmit':
drivers/net/82596.c:1088: warning: cast to pointer from integer of different size
drivers/net/82596.c:1099: warning: cast to pointer from integer of different size
drivers/net/82596.c: In function 'i596_interrupt':
drivers/net/82596.c:1404: warning: cast to pointer from integer of different size
(ugh)
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change error message when alloc_cpumask_var fails.
Repairs "cpumask: convert drivers/net/sfc".
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch fixes issues with dev->dev_addr changing from array to pointer.
Hopefully there are no others.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6:
iwlwifi: fix device id registration for 6000 series 2x2 devices
ath5k: update channel in sw state after stopping RX and TX
rtl8187: use DMA-aware buffers with usb_control_msg
mac80211: avoid NULL ptr deref when finding max_rates in PID and minstrel
airo: airo_get_encode{,ext} potential buffer overflow
Pulled directly by Linus because Davem is off playing shuffle-board at
some Alaskan cruise, and the NULL ptr deref issue hits people and should
get merged sooner rather than later.
David - make us proud on the shuffle-board tournament!
|
|
When the i2400m receives data and the device indicates there has to be
reordering, we keep an sliding window implementation to sort the
packets before sending them to the network stack.
One of the "operations" that the device indicates is "queue a packet
and update the window start". When the queue is empty, this is
equivalent to "deliver the packet and update the window start".
That case was optimized in i2400m_roq_queue_update_ws() so that we
would not pointlessly queue and dequeue a packet. However, when the
optimization was active, it wasn't updating the window start. That
caused the reorder management code to get confused later on with what
seemed to be wrong reorder requests from the device.
Thus the fix implemented is to do the right thing and update the
window start in both cases, when the queue is empty (and the
optimization is done) and when not.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
|
Remove the return after the goto. We want the goto because it frees
memory as well as returning err.
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch makes the return type of some of the functions
void as those functions always return true
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Set the default WMM AC parameters for BK/BE/VI/VO parameters:
AC CWmin CW max AIFSN TXOP Limit TXOP Limit
(802.11b) (802.11a/g)
AC_BK 15 1023 7 0 0
AC_BE 15 1023 3 0 0
AC_VI 7 15 2 188 94
(6.016ms) (3.008ms)
AC_VO 3 7 2 102 47
(3.264ms) (1.504ms)
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Show current qos AC parameters in sysfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add "rate_scale_data" debugfs file to show current bit rate (HT and Legacy),
plus additional information (rssi, noise, tsf, beacon time stamp).
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of hard coded value, use the define in iwl-commands.h for
better code maintenance
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Read rev id in nic_config instead of nic_init.
Nic_config has some checking for rev_id but we actually don't read
the rev_id in there.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Somehow these pre-production cards are showing up in the community.
With this message we hope that it will be clear that the hardware is not
supported.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
iwlagn rate scaling will periodically search other rate scale
tables to switch to the best table regarding performance. In the past
the number of search tables were 3. Every time the rate scale algorithm
goes through these available tables in will stay in current table for
some time before start searching again. Recent driver support more
feature and antenna, so we have more tables to search. This patch make
sure we go through all available tables.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This removes all the dead code that tries to adjust the power
saving level based on the system AC state (inacceptable policy
in the kernel) or based on overtemp conditions (unused).
Also, pass _all_ policy wrt. enabling PS to mac80211, since
we do not use the power_disabled internally I now use that to
mirror the mac80211 CONF_PS setting. When mac80211 turns off
CONF_PS we follow suit. This means that the user power level
(which can currently only be set from sysfs) is not touched
for mac80211 powersave changes.
This means no "association status" checks are necessary since
mac80211 will not allow power save to be enabled when not
associated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
iwlwifi internally needs to keep track of whether PS
is enabled in the firmware or not. To do this, it keeps
a bit in the status flags, called STATUS_POWER_PMI.
The code to set this bit looks as follows:
static int iwl_set_power(struct iwl_priv *priv, void *cmd)
{
return iwl_send_cmd_pdu_async(priv, POWER_TABLE_CMD,
sizeof(struct iwl_powertable_cmd),
cmd, NULL);
}
int iwl_power_update_mode(...)
{
[...]
if (final_mode != IWL_POWER_MODE_CAM)
set_bit(STATUS_POWER_PMI, &priv->status);
iwl_update_power_cmd(priv, &cmd, final_mode);
cmd.keep_alive_beacons = 0;
if (final_mode == IWL_POWER_INDEX_5)
cmd.flags |= IWL_POWER_FAST_PD;
ret = iwl_set_power(priv, &cmd);
if (final_mode == IWL_POWER_MODE_CAM)
clear_bit(STATUS_POWER_PMI, &priv->status);
else
set_bit(STATUS_POWER_PMI, &priv->status);
if (priv->cfg->ops->lib->update_chain_flags && update_chains)
priv->cfg->ops->lib->update_chain_flags(priv);
[...]
}
Now, this bit really needs to track what the _firmware_
thinks, not what the driver thinks. Therefore, there is
a race condition here -- the driver sets the bit before
it knows that the async command sent to the card in the
iwl_set_power function has been processed. As a result,
the call to update_chain_flags() may think that the card
has been woken up (PMI bit cleared) while in reality it
hasn't processed the async POWER_TABLE_CMD yet.
This leads to bugs -- any commands the update_chain_flags
function sends can get stuck and subsequent commands also
fail.
The fix is almost trivial: since there's no reason to send
an async command here (in fact, there almost never should
be since many mac80211 callbacks can sleep) just make the
function wait for the card to process the command and then
return and clear the PMI bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the microcode fails for any reason, ask mac80211 to
recover instead of trying ourselves and failing at it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There really is no need to have a separate struct for a
single variable. The fact that it exists is due to the
code legacy, but we can remove that now. Very simple.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The lower 4 bytes of the chipset revision must contain
a non-zero value. This bug was introduced by
"rt2x00: Simplify rt2x00_check_rev".
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It's not needed outside iwl-core.c
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
m68k allmodconfig:
| drivers/net/wireless/wl12xx/main.c: In function 'wl12xx_probe':
| drivers/net/wireless/wl12xx/main.c:1273: error: implicit declaration of function 'set_irq_type'
| make[1]: *** [drivers/net/wireless/wl12xx/main.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add device ids for 2x2 devices. Also fix antenna usage because these devices use
antennas A and B, not B and C.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes a non-theoretical race condition when transmitting and
receiving frames during a scan. If the channel or operating band
changes while processing status descriptors in the tasklets, ath5k
will incorrectly use the new channel and band when reporting the
rates, even if the frame was actually sent on a previous channel.
Typically this will manifest as a beacon found on an incorrect
frequency and/or a warning in the driver while scanning:
[ 4773.891944] cfg80211: Found new beacon on frequency: 5805 MHz (Ch 161) on phy0
[ 4785.461125] ------------[ cut here ]------------
[ 4785.461135] WARNING: at drivers/net/wireless/ath/ath5k/base.c:1141 ath5k_tasklet_rx+0x2ff/0x577 [ath5k]()
[ 4785.461143] Hardware name: MacBook1,1
[ 4785.461148] invalid hw_rix: 1b
[ 4785.461152] Modules linked in: fuse i915 drm af_packet acpi_cpufreq binfmt_misc dm_mirror dm_region_hash dm_log dm_multipath dm_mod arc4 ecb snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_seq_dummy snd_seq_oss snd_seq_midi_event ath5k snd_seq hid_apple usbhid snd_seq_device mac80211 appletouch snd_pcm_oss sky2 ohci1394 snd_mixer_oss ath ieee1394 snd_pcm bitrev snd_timer cfg80211 crc32 snd snd_page_alloc button processor ac ehci_hcd joydev uhci_hcd sg battery thermal sr_mod cdrom applesmc evdev input_polldev unix [last unloaded: microcode]
[ 4785.461296] Pid: 0, comm: swapper Tainted: G W 2.6.30-rc3-wl #112
[ 4785.461302] Call Trace:
[ 4785.461316] [<c012590f>] warn_slowpath+0x76/0xa5
[ 4785.461331] [<c0219839>] ? debug_dma_unmap_page+0x5a/0x62
[ 4785.461357] [<f9982f88>] ath5k_tasklet_rx+0x2ff/0x577 [ath5k]
[ 4785.461371] [<c01446f7>] ? trace_hardirqs_off+0xb/0xd
[ 4785.461381] [<c0129928>] ? __tasklet_schedule+0x6e/0x7c
[ 4785.461392] [<c0129b02>] tasklet_action+0x92/0xe5
[ 4785.461402] [<c0129f91>] __do_softirq+0xb1/0x182
[ 4785.461411] [<c012a092>] do_softirq+0x30/0x48
[ 4785.461428] [<c012a20a>] irq_exit+0x3d/0x74
[ 4785.461435] [<c035a0de>] do_IRQ+0x76/0x8c
[ 4785.461440] [<c010312e>] common_interrupt+0x2e/0x34
[ 4785.461445] [<c014007b>] ? timer_list_show+0x1ab/0x939
[ 4785.461457] [<f85fd25c>] ? acpi_idle_enter_bm+0x27c/0x2b9 [processor]
[ 4785.461463] [<c02d1ed6>] cpuidle_idle_call+0x6a/0x9c
[ 4785.461468] [<c0101cc8>] cpu_idle+0x53/0x87
[ 4785.461473] [<c0346584>] rest_init+0x6c/0x6e
[ 4785.461479] [<c04df74d>] start_kernel+0x286/0x28b
[ 4785.461484] [<c04df037>] __init_begin+0x37/0x3c
[ 4785.461487] ---[ end trace aaf8496ba3679dfb ]---
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Feeding the return code of get_wep_key directly to the length parameter
of memcpy is a bad idea since it could be -1...
Reported-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
bonding: fix panic if initialization fails
IXP4xx: complete Ethernet netdev setup before calling register_netdev().
IXP4xx: use "ENODEV" instead of "ENOSYS" in module initialization.
ipvs: Fix IPv4 FWMARK virtual services
ipv4: Make INET_LRO a bool instead of tristate.
net: remove stale reference to fastroute from Kconfig help text
net: update skb_recycle_check() for hardware timestamping changes
bnx2: Fix panic in bnx2_poll_work().
net-sched: fix bfifo default limit
igb: resolve panic on shutdown when SR-IOV is enabled
wimax: oops: wimax_dev_add() is the only one that can initialize the state
wimax: fix oops if netlink fails to add attribute
Bluetooth: Move dev_set_name() to a context that can sleep
netfilter: ctnetlink: fix wrong message type in user updates
netfilter: xt_cluster: fix use of cluster match with 32 nodes
netfilter: ip6t_ipv6header: fix match on packets ending with NEXTHDR_NONE
netfilter: add missing linux/types.h include to xt_LED.h
mac80211: pid, fix memory corruption
mac80211: minstrel, fix memory corruption
cfg80211: fix comment on regulatory hint processing
...
|
|
This patch adds three attribute files in /sys/class/net/$dev/ for tun
devices; allowing userspace to obtain the information which TUNGETIFF
offers, and more, but without having to attach to the device in question
(which may not be possible if it's in use).
It also fixes a bug which has been present in the TUNGETIFF ioctl since
its inception, where it would never set IFF_TUN or IFF_TAP according to
the device type. (Look carefully at the code which I remove from
tun_get_iff() and how the new tun_flags() helper is subtly different).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6
|
|
If module initialisation failed (e.g. because the bonding sysfs entry
cannot be created), kernel panics:
IP: [<ffffffff8024910a>] destroy_workqueue+0x2d/0x146
Call Trace:
[<ffffffff808268c4>] bond_destructor+0x28/0x78
[<ffffffff80b64471>] netdev_run_todo+0x231/0x25a
[<ffffffff80b6dbcd>] rtnl_unlock+0x9/0xb
[<ffffffff81567907>] bonding_init+0x83e/0x84a
Remove the calls to bond_work_cancel_all() and destroy_workqueue();
both are also called/scheduled via bond_free_all().
bond_destroy_sysfs is unecessary because the sysfs entry has
not been created in the error case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ETH_P_SLOW is already defined in include/linux/if_ether.h.
There's no need to define BOND_ETH_P_LACPDU in drivers/net/bonding/bond_3ad.h
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary length parameter since it's always 4 bytes.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This board doesn't suppot msi-x well due to msi-x table
mapping (hardware) issue.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Fix the order of irq and hardware context teardown.
Also synchronize the interrupt in dev close() before
releasing tx buffers.
o Fix possible msi-x vector leak if available vectors are
less than requested.
o Request multiple msix vectors only if hardware supports
multiple rx queues.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Store msi target status register offset in adapter struct.
This avoids contention on msi_tgt_status table from interrupt
hadlers of different pci function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
