| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit d4fb6514ff8ed6912a71294e6b66a5d59ee88007 upstream.
The can_skb_priv::skbcnt variable is used to identify CAN skbs in the RX
path analogue to the skb->hash.
As the skb hash is not filled in CAN skbs move the private skbcnt value to
skb->hash and set skb->sw_hash accordingly. The skb->hash is a value used
for RPS to identify skbs. Use it as intended.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260201-can_skb_ext-v8-1-3635d790fe8b@hartkopp.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bfa858f220ab8c950dd3e1310fee61950d0ecdae ]
To be able to constify instances of struct ctl_tables it is necessary to
remove ways through which non-const versions are exposed from the
sysctl core.
One of these is the ctl_table_arg member of struct ctl_table_header.
Constify this reference as a prerequisite for the full constification of
struct ctl_table instances.
No functional change.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f8d5e7846025 ("sctp: avoid auth_enable sysctl UAF during netns teardown")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 43b25879f004c98defa2776bedc6ca4763c51945 ]
brcmf_fw_crashed() and the debugfs "reset" entry both schedule
drvr->bus_reset, whose callback recovers drvr through container_of()
and dereferences it. The removal path frees drvr (brcmf_free ->
wiphy_free) without draining the work, so a bus_reset callback pending
or running during removal can outlive drvr.
Cancellation cannot live in brcmf_detach() or brcmf_free(): the work
callback reaches teardown through the bus .reset op (PCIe
brcmf_pcie_reset -> brcmf_detach; SDIO brcmf_sdio_bus_reset ->
brcmf_sdiod_remove -> brcmf_free), so cancelling there would wait for
the running work and deadlock.
Add a per-bus mutex (bus_reset_lock) and route all arming through
brcmf_bus_schedule_reset(), which under the lock skips when the bus is
marked removing. Each bus remove entry calls
brcmf_bus_cancel_reset_work(), which under the same lock sets removing
and cancels the work. Holding the mutex across cancel_work_sync() makes
the set-removing + drain step atomic. Every producer reaches the arming
path from process context -- the PCIe firmware-halt notification runs in
the threaded IRQ handler (brcmf_pcie_isr_thread) and the SDIO hostmail
path runs from the data workqueue -- so the mutex is taken only in
sleepable contexts. Where applicable the remove entry first stops the
firmware-crash producer: on PCIe mask the mailbox and synchronize_irq;
on SDIO unregister the bus interrupt and cancel the data worker, which
also reports firmware halts through brcmf_fw_crashed(). The mutex is
initialized at bus allocation. The SDIO suspend power-off path frees
drvr through the same brcmf_sdiod_remove() and takes the same lock;
resume re-allows the work only on a successful re-probe.
Also guard brcmf_fw_crashed() against a NULL bus_if/drvr: it can fire
before brcmf_attach() wires up drvr, and it dereferences drvr
(bphy_err/brcmf_dev_coredump) before reaching the arming gate.
The bus_reset work is shared across buses, so the drain is applied to
every remove path: PCIe (the .reset op introduced by the Fixes commit),
SDIO (arms the same work through brcmf_fw_crashed()), and USB (via the
debugfs "reset" entry). cancel_work_sync() drains a running or pending
bus_reset work item before removal frees drvr, and patch 1/2 makes the
scratch-buffer release safe when reset teardown has already released
those DMA buffers.
This patch fixes the lifetime of the bus_reset work item itself. It does
not attempt to address the separate, pre-existing lifetime of the
asynchronous firmware completion started by the PCIe reset path. That
callback needs its own lifetime/ownership protocol and is being tracked
separately.
This issue was found by an in-house static analysis tool.
Fixes: 4684997d9eea ("brcmfmac: reset PCIe bus on a firmware crash")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Assisted-by: Codex:gpt-5.6
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260718024353.3147201-3-fanwu01@zju.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 29ab31f3f27157648f2f7e6d5e1fd9792fdf0614 ]
The BCM43752 is not reliable with the default 512-byte SDIO function 2
block size: on an i.MX8MP board with an AMPAK AP6275S module at
SDR104 / 200 MHz, an iperf TX stress test kills WLAN within seconds:
mmc_submit_one: CMD53 sg block write failed -84
brcmf_sdio_dpc: failed backplane access over SDIO, halting operation
Commit d2587c57ffd8 ("brcmfmac: add 43752 SDIO ids and initialization")
set up the 43752 like the 4373 for the F2 watermark but missed the F2
block size, which the 4373 limits to 256 bytes. The vendor driver
(bcmdhd) also programs a 256-byte F2 block size for this chip and runs
the same hardware without errors.
Group the 43752 with the 4373, matching the F2 watermark handling.
With this change a 10-minute bidirectional iperf3 soak completes with
zero SDIO errors at ~270 Mbit/s in each direction.
Backporting note: kernels before v6.18 name this id
SDIO_DEVICE_ID_BROADCOM_CYPRESS_43752, so on those trees the case
label added by this patch must be adjusted to that name. Cherry-picking
the rename commit 74e2ef72bd4b ("wifi: brcmfmac: fix 43752 SDIO FWVID
incorrectly labelled as Cypress (CYW)") first is not a clean
alternative: on trees before v6.17 its context collides with the 43751
additions, and trees before v6.2 lack the FWVID framework it touches.
Fixes: d2587c57ffd8 ("brcmfmac: add 43752 SDIO ids and initialization")
Cc: stable@vger.kernel.org # see patch description, needs adjustments for <= 6.17
Signed-off-by: LiangCheng Wang <zaq14760@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260715-b43752-f2-blksz-v2-1-f9be49856050@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 74e2ef72bd4b25ce21c8f309d4f5b91b5df9ff5b ]
Cypress(Infineon) is not the vendor for this 43752 SDIO WLAN chip, and so
has not officially released any firmware binary for it. It is incorrect to
maintain this WLAN chip with firmware vendor ID as "CYW". So relabel the
chip's firmware Vendor ID as "WCC" as suggested by the maintainer.
Fixes: d2587c57ffd8 ("brcmfmac: add 43752 SDIO ids and initialization")
Fixes: f74f1ec22dc2 ("wifi: brcmfmac: add support for Cypress firmware api")
Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250724101136.6691-1-gokulkumar.sivakumar@infineon.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: 29ab31f3f271 ("wifi: brcmfmac: set F2 blocksize to 256 for BCM43752")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ba7debb4dd6427386862220e8335a53a4bfc235d ]
The aggr_reset_state() function uses timer_delete() (non-synchronous)
for the aggregation timer before proceeding to delete TID state and
before the structure is freed by callers like aggr_module_destroy().
If the timer callback (aggr_timeout) is executing when aggr_reset_state()
is called, the callback will continue to access aggr_conn fields like
rx_tid[] and stat[] which may be freed immediately after by
kfree(aggr_info->aggr_conn) in aggr_module_destroy().
Additionally, the timer callback can re-arm itself via mod_timer() while
aggr_reset_state() is running, creating a more complex race condition.
Use timer_delete_sync() instead to ensure any running timer callback
has completed before returning.
Fixes: bdcd81707973 ("Add ath6kl cleaned up driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Hodges <git@danielhodges.dev>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20260206185207.30098-1-git@danielhodges.dev
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e735cbe3affe88001428fdd9cae8e685ce92f21 upstream.
In the CAN_STATE_ERROR_ACTIVE case, cf->data[1] is set to
CAN_ERR_CRTL_ACTIVE, but cf->can_id is not set with CAN_ERR_CRTL in
that path.
Set CAN_ERR_CRTL so consumers know the controller-status information
in cf->data[1] is valid.
Fixes: 9bd24927e3ee ("can: ctucanfd: handle skb allocation failure")
Signed-off-by: Avi Weiss <thnkslprpt@gmail.com>
Link: https://patch.msgid.link/20260723155543.318414-1-thnkslprpt@gmail.com
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e74bae899529f49c0f375307983d12e8ecad7d4b upstream.
Include REG_INT_STAT_BEI in the top-level error interrupt condition.
BEI is enabled when CAN_CTRLMODE_BERR_REPORTING is requested and
ctucan_err_interrupt() already handles it. Without checking and
clearing BEI in the top-level handler, bus error interrupts are not
handled or acknowledged.
Fixes: 2dcb8e8782d8 ("can: ctucanfd: add support for CTU CAN FD open-source IP core - bus independent part.")
Signed-off-by: Avi Weiss <thnkslprpt@gmail.com>
Acked-by: Pavel Pisa <pisa@fel.cvut.cz>
Link: https://patch.msgid.link/20260723074403.131575-1-thnkslprpt@gmail.com
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6873910f983096746d1a2e0af94f36b8003e839 upstream.
BAR0 is mapped into bar0_base, while cra_addr points to an offset
within that mapping and is used for other purposes.
Pass bar0_base to pci_iounmap(), instead of cra_addr, on the probe error
path so the address returned by pci_iomap() is used for unmapping.
Fixes: 792a5b678e81 ("can: ctucanfd: CTU CAN FD open-source IP core - PCI bus support.")
Signed-off-by: Avi Weiss <thnkslprpt@gmail.com>
Acked-by: Pavel Pisa <pisa@fel.cvut.cz>
Link: https://patch.msgid.link/20260723095934.181042-1-thnkslprpt@gmail.com
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c31a435933f18be0f874302161333e9f16e200a0 upstream.
Use self-test mode for CAN_CTRLMODE_PRESUME_ACK so transmitted
frames can complete without receiving an ACK.
ACK forbidden mode prevents the controller from acknowledging
received frames and does not implement the presume-ack behavior.
Fixes: 2dcb8e8782d8 ("can: ctucanfd: add support for CTU CAN FD open-source IP core - bus independent part.")
Signed-off-by: Avi Weiss <thnkslprpt@gmail.com>
Acked-by: Pavel Pisa <pisa@fel.cvut.cz>
Link: https://patch.msgid.link/20260722192726.230729-1-thnkslprpt@gmail.com
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d937bdb244a751fe5967052ea2d64a7b2c476cc0 upstream.
The driver has a match table for the pci bus wired into its driver
structure, but the table is not exported with MODULE_DEVICE_TABLE().
Add the missing MODULE_DEVICE_TABLE() entry so module alias information
is generated for automatic module loading.
This is a source-level fix. It does not claim dynamic hardware
reproduction; the evidence is the driver-owned match table, its use by
the driver registration structure, and the missing module alias
publication.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Acked-by: Pavel Pisa <pisa@fel.cvut.cz>
Link: https://patch.msgid.link/20260704151957.48194-1-pengpeng@iscas.ac.cn
Fixes: 792a5b678e81 ("can: ctucanfd: CTU CAN FD open-source IP core - PCI bus support.")
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93fcab2c6968446316bbb49548848df604d6346f upstream.
pcan_usb_fd_decode_buf() walks uCAN records packed in one USB
receive buffer.
Require each record to contain the fixed header for its type, and verify
CAN payload bytes before copying them into the skb.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260706092836.79754-1-pengpeng@iscas.ac.cn
Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
submit error
commit 9b3d5a6d952c38bbcf07f903cbeadefdb56b9bc9 upstream.
In peak_usb_start(), each RX URB transfer buffer is allocated with kmalloc()
and the URB is flagged URB_FREE_BUFFER so that the final usb_free_urb() also
frees the transfer buffer.
If usb_submit_urb() fails, the error path frees the buffer explicitly with
kfree(buf) and then calls usb_free_urb(urb). Because URB_FREE_BUFFER is set,
usb_free_urb() -> urb_destroy() frees the same buffer a second time, a double
free of the transfer buffer.
BUG: KASAN: double-free in usb_free_urb.part.0+0x91/0xb0
Free of addr ffff8881069ccb80 by task trigger.sh/285
Call Trace:
kfree+0x113/0x3c0
usb_free_urb.part.0+0x91/0xb0
Drop the redundant kfree(buf); usb_free_urb() already releases the transfer
buffer. This mirrors commit 03819abbeb11 ("net: usb: lan78xx: Fix double free
issue with interrupt buffer allocation").
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core")
Closes: https://lore.kernel.org/linux-can/178159320216.2154888.16953451793788581739@maoyixie.com/T/#u
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol@kernel.org>
Link: https://patch.msgid.link/178163373110.2507866.216458825145756798@maoyixie.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 39132f166ca8ce00ae60d8a9068e06a60943cc4b upstream.
The channel control index ctrl_idx is derived from rx->len which comes
directly from a device USB payload. The mask 0x0f allows values 0-15, but
the array size of usb_if->dev[] is only 2. Values 2-15 cause heap
out-of-bounds read, eventually causing kernel panic in the IRQ context.
Add bounds checking for ctrl_idx before the array access in both
pcan_usb_pro_handle_canmsg() and pcan_usb_pro_handle_error().
Fixes: d8a199355f8f ("can: usb: PEAK-System Technik PCAN-USB Pro specific part")
Signed-off-by: James Gao <jamesgao5@outlook.com>
Reviewed-by: Vincent Mailhol <mailhol@kernel.org>
Link: https://patch.msgid.link/TYWPR01MB8559DBAAAA6A7F410400329CF0012@TYWPR01MB8559.jpnprd01.prod.outlook.com
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 856d6cb04e5407523566b075841dcd6423757d1c upstream.
fw_parse() reads a fixed record header, a firmware-provided payload,
and a trailing checksum without knowing the end of the firmware blob. A
truncated record can therefore make those reads exceed the blob.
The same record also supplies addresses and lengths for writes into
DPRAM. The generic loader uses wrap-prone mixed signed arithmetic for its
bounds check, while the application loader does not bound the staging
copy at all.
Pass the firmware end to the parser and validate the full source record.
Use a signed wide offset for generic DPRAM records and validate the
application staging span against the mapped DPRAM before copying.
Fixes: 03fd3cf5a179 ("can: add driver for Softing card")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260722044347.2708-1-pengpeng@iscas.ac.cn
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
extents
commit 0293dd153f9dbc1ddf5dacdccc76b363bce4a8ee upstream.
The wait and bulk receive paths walk variable-length commands from a
USB buffer. A nonzero command shorter than CMD_HEADER_LEN can still be
dispatched, and the wait path copies a matching command into a fixed
caller-owned struct kvaser_cmd using the device-provided length.
Reject nonzero commands that do not contain the fixed header or that
extend beyond the current USB buffer item. In the wait path, also reject
a matching command that exceeds the destination before copying it.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260722042221.44066-1-pengpeng@iscas.ac.cn
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kvaser_usb_hydra_get_busparams()
commit 941eaf9a6d3b33dea49f2c0a1da7546a03b6ff71 upstream.
The memory allocated for cmd is not freed after the call to
kvaser_usb_send_cmd() in both the normal and error paths.
Fix that by adding a kfree() immediately after the call.
Fixes: 39d3df6b0ea8 ("can: kvaser_usb: Compare requested bittiming parameters with actual parameters in do_set_{,data}_bittiming")
Cc: stable@vger.kernel.org
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Link: https://patch.msgid.link/20260722103906.108571-1-nihaal@cse.iitm.ac.in
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
failure
commit 68c5724ecd159992f76edb7b57dc508a44c8b7da upstream.
If the allocation of the SKB in gs_usb_receive_bulk_callback() fails, the
driver returns from the callback without resubmitting the URB in order to
receive further USB in URBs.
This results in a silent performance degradation which, if it occurs
repeatedly, results in starvation of USB in traffic.
Instead of returning immediately, try to resend the URB. If this also
fails, this is logged as an info message.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Fixes: 26949ac935e3 ("can: gs_usb: add CAN-FD support")
Link: https://patch.msgid.link/20260709-gs_usb-resubmit-urb-v1-1-4dd40030cc84@pengutronix.de
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
resubmit failure
commit 7a0cf2b2497c757c3cb1286eddf2986abb0d387b upstream.
es58x_read_bulk_callback() resubmits the RX URB after processing a received
packet. If the resubmit succeeds, the URB remains anchored and will be
handled by the normal RX path or by teardown.
However, if usb_submit_urb() fails, the callback unanchors the URB and then
returns directly. This skips the existing free_urb path, so the coherent
transfer buffer allocated with usb_alloc_coherent() is not released.
Reuse the existing free_urb path after a resubmit failure so that the RX
coherent buffer is freed before leaving the callback.
Fixes: 5eaad4f76826 ("can: usb: etas_es58x: correctly anchor the urb in the read bulk callback")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol@kernel.org>
Link: https://patch.msgid.link/20260706014601.415445-1-lgs201920130244@gmail.com
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 02925f51377f2a42a6724f00549167499c9302e5 upstream.
ems_usb_read_bulk_callback() walks CPC messages packed in one USB
receive buffer.
Check that each declared message fits in the URB payload. Also require the
type-specific payload to cover the fields used by the CAN, state, error and
overrun handlers.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260706092752.79600-1-pengpeng@iscas.ac.cn
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
bittiming is configured
commit 26504844613fb44c7cab1c5f6fcff77861709baa upstream.
c_can_chip_config() was programming C_CAN_CTRL_REG without CONTROL_INIT,
which may allow the controller to become active before
c_can_set_bittiming() finishes.
That creates a short timing window where the peripheral can interact with
the bus using a different/default bitrate, potentially generating bus
errors and corrupting traffic.
Set CONTROL_INIT together with the control-mode writes in
c_can_chip_config() (normal, loopback and listen-only paths), so the
controller stays halted until bit timing is fully programmed.
This prevents transient bus disturbance during startup when the configured
bitrate differs from the active bus bitrate.
Signed-off-by: Lucas Martins Alves <lucas.alves@lumal21.com.br>
Link: https://patch.msgid.link/20260714164839.771123-1-lucas.alves@lumal21.com.br
Fixes: 881ff67ad450 ("can: c_can: Added support for Bosch C_CAN controller")
Cc: stable@kernel.org
[mkl: remove space before close parenthesis]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a9de5590da4ffd9e9c541c4c4d492aa2b54cf6e upstream.
ice_lbtest_prepare_rings() frees Rx rings only when
ice_vsi_start_all_rx_rings() fails. If ice_vsi_setup_rx_rings() fails
after allocating some descriptors, or if ice_vsi_cfg_lan() fails after
the Rx rings were prepared, the function reaches the Tx cleanup path
without releasing the initialized Rx resources.
Fix this by adding separate unwind paths for Rx setup failure and LAN
configuration failure. The Rx setup failure path releases the partially
prepared Rx rings before freeing Tx rings, while later failures first
undo the LAN Tx configuration and then release the Rx rings in reverse
setup order.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc7.
An x86_64 allyesconfig build showed no new warnings. As we do not have an
Intel E800 Series adapter available to run the ethtool offline loopback
selftest, no runtime testing was able to be performed.
Fixes: 0e674aeb0b77 ("ice: Add handler for ethtool selftest")
Cc: stable@vger.kernel.org
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2816d613f388814d27bc9fd6dbd931a88056e19 upstream.
ice_resume() schedules an asynchronous PF reset and returns
immediately. The reset runs later in ice_service_task(). If
userspace tries to bring up the net device before the reset
finishes, ice_open() fails with -EBUSY:
ice_resume()
ice_schedule_reset() # sets ICE_PFR_REQ, returns
...
ice_open()
ice_is_reset_in_progress() # ICE_PFR_REQ still set, -EBUSY
...
ice_service_task()
ice_do_reset()
ice_rebuild() # clears ICE_PFR_REQ, too late
Reproduced on E800 series NICs during suspend/resume with irdma
enabled, where the aux device probe widens the race window.
ice 0000:81:00.0: can't open net device while reset is in progress
Add a best-effort wait (10s timeout, matching ice_devlink_info_get())
for the reset to complete before returning from ice_resume(). In
practice the reset completes in ~300ms.
Fixes: 769c500dcc1e ("ice: Add advanced power mgmt for WoL")
Cc: stable@vger.kernel.org
Reviewed-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26bb2dd0a8839617e2c79ffbbe1923f8e4bab9fb upstream.
route_shortcircuit() currently calls pskb_may_pull(skb, sizeof(struct iphdr))
(or ipv6hdr), which checks if bytes are available starting from skb->data.
However, in vxlan_xmit(), skb->data points to the MAC header, so
skb_network_offset(skb) is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, 20)
only checks 20 bytes from skb->data (which is 14 bytes MAC header + 6 bytes of
IP header), leaving the rest of the IP header potentially un-pulled in non-linear
frags. Subsequent dereferences of ip_hdr(skb)->daddr can read beyond the pulled
linear buffer length.
Fix this by using pskb_network_may_pull(), which adds skb_network_offset(skb) to
the length check to ensure the full network header is present in the linear buffer.
Fixes: e4f67addf158 ("add DOVE extensions for VXLAN")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260723144249.759100-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8eca411347e1d38964f9ed2c8d3b6ab0e7e4473d upstream.
The neighbour hardware address n->ha can be updated asynchronously by the
neighbour subsystem, protected by n->ha_lock seqlock. Reading n->ha without
holding the seqlock loop can lead to torn reads or reading a partially updated
MAC address.
Use neigh_ha_snapshot() in route_shortcircuit() to safely copy n->ha under
read_seqbegin()/read_seqretry() lock protection before using it.
Note that arp_reduce() and neigh_reduce() seem to have the same issue
left for future patches.
Fixes: e4f67addf158 ("add DOVE extensions for VXLAN")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260723144249.759100-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 760d36e737f2b3867762f42af36c663f55babcc4 upstream.
When route_shortcircuit() performs L3 short-circuit routing, it modifies
the Ethernet header of the skb in-place:
memcpy(eth_hdr(skb)->h_source, eth_hdr(skb)->h_dest, dev->addr_len);
memcpy(eth_hdr(skb)->h_dest, n->ha, dev->addr_len);
If the incoming skb is cloned (for example by packet sockets, tcpdump, or
dev_queue_xmit), modifying the Ethernet header without uncloning can corrupt
the packet header for other readers holding a reference to the cloned skb.
Ensure the skb header is writable and unshared by calling skb_cow_head(skb, 0)
prior to updating the Ethernet header. If skb_cow_head() fails, abort short-circuiting
and return false to allow standard packet processing fallback.
Fixes: e4f67addf158 ("add DOVE extensions for VXLAN")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260723144249.759100-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1395a676ec15a0a02a2a6d86602324f2d5fd41d5 upstream.
Before route_shortcircuit(), the eth header pointer is cached from eth_hdr(skb).
Inside route_shortcircuit(), pskb_may_pull() can be called, which may
reallocate skb->head.
In this case, returning to vxlan_xmit() leaves the cached eth pointer pointing to
freed memory, leading to a use-after-free when dereferencing eth->h_dest.
Fix this by updating eth = eth_hdr(skb) after calling route_shortcircuit().
Fixes: ae8840825605 ("VXLAN: Allow L2 redirection with L3 switching")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260723144249.759100-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99a948382af8a225e2d5e54a7052158cd6281cc6 upstream.
mwifiex_11n_dispatch_amsdu_pkt() splits an A-MSDU with
ieee80211_amsdu_to_8023s() and walks the resulting subframes. For each
subframe it passes the subframe data pointer to
mwifiex_process_tdls_action_frame(), but pairs it with skb->len, the
length of the A-MSDU parent, instead of rx_skb->len:
rx_skb = __skb_dequeue(&list);
rx_hdr = (struct rx_packet_hdr *)rx_skb->data;
if (ISSUPP_TDLS_ENABLED(priv->adapter->fw_cap_info) &&
ntohs(rx_hdr->eth803_hdr.h_proto) == ETH_P_TDLS) {
mwifiex_process_tdls_action_frame(priv, (u8 *)rx_hdr,
skb->len);
}
The parent is not a valid description of that buffer, and may not be
valid memory at all. ieee80211_amsdu_to_8023s() ends with
if (!reuse_skb)
dev_kfree_skb(skb);
and it only sets reuse_skb when the parent is linear, is not a
head_frag, and is being consumed as the *last* subframe. So when the
parent does not qualify for reuse it has already been freed, and the
read of skb->len is a use-after-free. When it is reused, skb->len is
the length of the last subframe, applied to every earlier subframe,
which over-states the buffer whenever an earlier subframe is shorter.
The callee cannot absorb a wrong length, because it derives its own
ceiling from the value it is given. Each frame type computes
ies_len = len - sizeof(struct ethhdr) - TDLS_*_FIX_LEN;
and the element walk is then bounded entirely against that ceiling,
for (end = pos + ies_len; pos + 1 < end; pos += 2 + pos[1]) {
u8 ie_len = pos[1];
if (pos + 2 + ie_len > end)
break;
so a too-large len moves end past the end of the subframe and the walk
reads and copies beyond it. The A-MSDU layout is chosen by the sender,
which makes the difference between the last subframe and a shorter
earlier one remotely selectable. Reaching this requires TDLS support in
firmware and the TDLS ethertype on the subframe.
The other caller, mwifiex_process_rx_packet(), is correct: it passes a
pointer and a length that describe the same region of the RX buffer.
Pass rx_skb->len, the length of the subframe actually being parsed.
Fixes: 776f742040ca ("mwifiex: fix AMPDU not setup on TDLS link problem")
Assisted-by: Codex:gpt-5.6-sol
Assisted-by: Kimi:K3
Cc: stable@vger.kernel.org
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260728115325.19128-1-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0565052b7e2f436b7f1541f4849da96dc0aa7a0e upstream.
If an error is encountered while mapping TX buffers, the driver should
unmap any buffers already mapped for that skb.
Because count is incremented before each frag mapping, it will always
match the correct number of unmappings needed when dma_error is reached.
Decrementing count before the while loop in dma_error causes an
off-by-one error. If any mapping was successful before an unsuccessful
mapping, exactly one DMA mapping (the head) would leak.
This bug was introduced by a 2010 fix for an endless loop in dma_error.
All other affected drivers have already been fixed.
Fixes: c1fa347f20f1 ("e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of unsigned in *_tx_map()")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-4-7-opus
Signed-off-by: Matt Vollrath <tactii@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 816419dfea5c88126f35eb7a1b429a1bf546665e upstream.
In the e1000_probe() path, e1000_sw_init() allocates adapter->tx_ring and
adapter->rx_ring. If the subsequent CE4100-specific MDIO BAR mapping
fails, the error handling jumps past the ring cleanup code, leaking both
allocations.
Fix this leak by moving the err_mdio_ioremap label above the ring
deallocation logic. This guarantees the proper release of these resources
and prevents the memory leak.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc6.
An x86_64 allyesconfig build showed no new warnings. As we do not have a
CE4100 reference platform to test with, no runtime testing was able to
be performed.
Fixes: 5377a4160bb65 ("e1000: Add support for the CE4100 reference platform")
Cc: stable@vger.kernel.org
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 451c9075d6c53f2438d110addbeeeea6fac18567 ]
A TX timeout on a qede NIC that has VXLAN/GENEVE tunnel ports
configured wedges the rtnetlink control plane of the whole machine:
NETDEV WATCHDOG: ens6f1 (qede): transmit queue 2 timed out 10226 ms
[qede_tx_timeout:586(ens6f1)]TX timeout on queue 2!
[qede_recovery_handler:2665(ens6f0)]Starting a recovery process
The recovery path deadlocks on the driver's own mutex:
qede_sp_task
rtnl_lock()
mutex_lock(&edev->qede_lock) <- taken
qede_recovery_handler
qede_load
udp_tunnel_nic_reset_ntf
__udp_tunnel_nic_device_sync
info->sync_table == qede_udp_tunnel_sync
mutex_lock(&edev->qede_lock) <- same task: deadlock
The mutex is not recursive, so the kworker blocks on itself with
rtnl_lock held, and neither lock is ever released. Every task that
calls rtnl_lock() afterwards (ip, ovs-vswitchd, lldpad, IPv6
addrconf, sshd) blocks forever while the node still answers ping.
In a vmcore from an affected production node rtnl_mutex.owner
decodes to the very kworker blocked at the innermost mutex_lock()
above.
Re-sync the tunnel ports from qede_sp_task() after the internal lock
is dropped, still under rtnl_lock as the udp_tunnel API requires.
This mirrors qede_open(), which calls udp_tunnel_nic_reset_ntf()
under rtnl without the internal lock.
qede_recovery_handler() now returns whether it has successfully
reloaded an open device, and the caller re-syncs the ports only in
that case. This keeps the old gating exactly: a device that was down
or a failed recovery returns false, as those paths never reached the
udp_tunnel_nic_reset_ntf() call before either.
This was the only user of the qede_lock()/qede_unlock() helpers, so
remove them.
Fixes: 8cd160a29415 ("qede: convert to new udp_tunnel_nic infra")
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Andrew Lunn <andrew+netdev@lunn.ch>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260726104311.1782900-1-den@openvz.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 16809472409d998afcda402e32b8229b389337c4 ]
During link down event, we were doing netif_tx_stop_all_queues() first
and then netif_carrier_off(). This can cause a potential race since
carrier is still on during down event. This patch reverse the calling
order to fix the issue.
Fixes: 50fe6c02e5ad ("octeontx2-pf: Register and handle link notifications")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260724072831.2415281-1-rkannoth@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 77a9ebe8818cf6dd1699bd6728cb5d66307801d7 ]
The MT7531 indirect PHY access functions poll MT7531_PHY_IAC through
a helper which returns 0 when the underlying read fails, so a failed
bus transaction clears MT7531_PHY_ACS_ST and the access carries on,
returning garbage PHY register data to phylib.
Poll using regmap_read_poll_timeout(), which stops on read errors and
propagates them. These functions hold the MDIO bus lock across the
whole sequence, so the unlocked regmap accesses remain correct. Remove
the now-unused _mt7530_unlocked_read().
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/79e85d68d210cc37342978171aa6432aa2954333.1785213071.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 51b093a7ba27476e1f639455f005e8d2e75390e4 ]
sxgbe_open() ignores the return value of init_dma_desc_rings() and
continues to program DMA with invalid ring addresses when allocation
fails. Check the return value and disconnect the PHY on failure.
Fixes: 1edb9ca69e8a ("net: sxgbe: add basic framework for Samsung 10Gb ethernet driver")
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c870f7e2890b9f78ac84515a9809cc5c183c975e ]
When RX descriptor ring allocation fails, init_dma_desc_rings() only
frees the partially allocated RX rings and returns. The TX rings that
were allocated earlier in the same function are leaked.
Rearrange error labels to clean up TX rings upon RX failures.
Fixes: 1edb9ca69e8a ("net: sxgbe: add basic framework for Samsung 10Gb ethernet driver")
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0fe1e3e8f3380d7862296a73b528d164e96c76b8 ]
In phylink_create() if phylink_register_sfp() returns an error, link_gpio
obtained by phylink_parse_fixedlink() is never released. While this is a
very unlikely scenario, it's worth to fix/handle this.
This was present from the very first implementation of phylink but got
relevant only with the introduction of ce0aa27ff3f6 ("sfp: add sfp-bus to
bridge between network devices and sfp cages") where additional function
were added after phylink_parse_fixedlink() making the release of link_gpio
needed if such additional function errored out.
While at it, restructure the exit condition of phylink_create() with the
goto pattern to reduce code duplication on handling error conditions.
Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260726150806.2437-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 22666ba1420164753d7b0f5a841986b25ace5435 ]
nv_remove() frees the per-CPU txrx_stats before unregister_netdev().
Until unregister completes, ndo_get_stats64, the NAPI/xmit data path,
and nv_close()/drain may still access txrx_stats, leading to a
use-after-free.
Free the stats only after unregister_netdev().
Fixes: f4b633b911fd ("forcedeth: use per cpu to collect xmit/recv statistics")
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Link: https://patch.msgid.link/20260723092637.2135095-1-chenguang.zhao@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b65352a1bac64442ad95e64f385b40ccb9f1b0db upstream.
When the system is under extreme memory pressure, page allocations can
fail during the Rx buffer refill loop. If the number of buffers posted
to hardware falls below a critical low threshold and the refill loop
exits due to allocation failures, the queue can stall:
1. The device drops incoming packets because there are no descriptors.
2. Since no packets are processed, no Rx completions are generated.
3. Because no completions occur, NAPI is never scheduled, preventing
the refill loop from running again even after memory is freed.
This results in a permanent queue stall.
Resolve this by introducing a starvation recovery timer for each Rx queue.
If the number of buffers posted to hardware falls below a critical low
threshold, start a timer to periodically reschedule NAPI. Once NAPI runs
and successfully refills the queue above the threshold, the timer is
not rescheduled.
The threshold is set to 32 because a single maximum-sized Receive Segment
Coalescing (RSC) packet can consume up to 19 descriptors in the Rx path.
Lower thresholds (such as 8 or 16) would be insufficient to process a
complete maximum-sized RSC packet, risking packet drops or unexpected
hardware behavior under memory pressure. Setting the threshold to 32
guarantees a safe margin to handle at least one full RSC packet.
Cc: stable@vger.kernel.org
Fixes: 9b8dd5e5ea48 ("gve: DQO: Add RX path")
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Signed-off-by: Eddie Phillips <eddiephillips@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20260709211906.3322883-1-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 96ca1e658ae459276292bd6d971ab5d8c7e0379a ]
ipa_smp2p_init() acquires two Qualcomm SMEM state handles with
qcom_smem_state_get(). However, neither the init error paths
nor ipa_smp2p_exit() release them.
Release both handles with qcom_smem_state_put() in the init
error paths and in ipa_smp2p_exit().
Fixes: 530f9216a953 ("soc: qcom: ipa: AP/modem communications")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Alex Elder <elder@riscstar.com>
Link: https://patch.msgid.link/20260624065955.2822765-1-haoxiang_li2024@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ kzalloc_obj() context line kept as kzalloc(sizeof(*smp2p), GFP_KERNEL) since ipa_smp2p.c was not yet converted in this tree ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 27f575836cfebbf872dec020428742b10650a955 ]
The MACB driver has since forever leaked the outgoing SKBs that
have not yet been marked as completed. They live in queue->tx_skb
which gets freed without remorse nor checking.
macb_free_consistent() gets called in a few codepaths, but only close will
trigger the added expressions. In macb_open() and macb_alloc_consistent()
failure cases, queues' tx_skb just got allocated and are empty.
Fixes: 89e5785fc8a6 ("[PATCH] Atmel MACB ethernet driver")
Cc: stable@vger.kernel.org
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20260702-macb-drop-tx-v4-1-1c833eebdbc8@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
[ adjusted context to free each queue's Tx/Rx rings individually since 6.12 lacks the single-dma_alloc_coherent refactor ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 62e7df6d042aeebd5efb581074e28865c04477be ]
otx2_init_hw_resources() initializes SQ aura and pool resources before
several later setup steps. On failure, err_free_sq_ptrs only frees SQB
pages, leaving the per-SQ sqb_ptrs arrays behind.
Use otx2_free_sq_res() for the SQ unwind path and let it free sqb_ptrs
even when sq->sqe has not been allocated yet.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1.1.
An x86_64 allyesconfig build showed no new warnings. As we do not have an
OcteonTX2 PF device and the corresponding AF mailbox setup to test with,
no runtime testing was able to be performed.
Fixes: caa2da34fd25 ("octeontx2-pf: Initialize and config queues")
Cc: stable@vger.kernel.org
Reviewed-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Link: https://patch.msgid.link/20260630071625.349996-1-dawei.feng@seu.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8cdcf3d2caacdee7ddd363705fb4d93b0c1a0915 ]
rvu_mbox_handler_lmtst_tbl_setup() uses req->base_pcifunc as a direct
index into the LMT map table to read another function's LMTLINE
physical base address and copy it into the caller's own LMT map table
entry. The mailbox dispatcher authenticates req->hdr.pcifunc from the
IRQ source, but req->base_pcifunc is a separate payload field and is
not sanitized.
Reject the request with -EPERM when a VF caller's base_pcifunc is not a
valid function under its own PF. is_pf_func_valid() bounds the FUNC field
to the PF's configured VF count, keeping the computed index inside the
caller's own slot block.
Fixes: 893ae97214c3 ("octeontx2-af: cn10k: Support configurable LMTST regions")
Reported-by: Yuhao Jiang <danisjiang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Link: https://patch.msgid.link/SYBPR01MB78811656934E713B77DA6CEDAFE62@SYBPR01MB7881.ausprd01.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Dropped `rvu->pdev` argument from `rvu_get_pf()` calls and folded in the `is_pf_func_valid()` de-static plus its `rvu.h` declaration from commit 2156a29aecff. ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2e2a83b4998af4384e677d3b2ac08565274279bf ]
Validate the packet length reported in the RX CQE before passing it
to skb processing. The CQE is supplied by the NIC device and should
not be blindly trusted.
Cc: stable@vger.kernel.org
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Link: https://patch.msgid.link/20260702041237.617719-2-decui@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aa6dcd5c8dd9ba1d7d0f60093bcda41c0d6d438d ]
lbtf_free_adapter() calls timer_delete(&priv->command_timer), which does
not wait for a running command_timer_fn() callback. lbtf_free_adapter()
runs on the teardown path right before ieee80211_free_hw() frees priv,
both in lbtf_remove_card() and in the probe error path. command_timer is
armed by mod_timer() in lbtf_cmd() whenever a firmware command is sent.
command_timer_fn() dereferences priv. If a command times out as the
device is removed, command_timer_fn() runs concurrently with teardown and
dereferences priv after it has been freed.
This is the same use-after-free that commit 03cc8f90d053 ("wifi: libertas:
fix use-after-free in lbs_free_adapter()") fixed in the sibling libertas
driver. The libertas_tf variant has the identical pattern and was left
unchanged. Use timer_delete_sync() so any in-flight callback completes
before priv is freed.
Fixes: 06b16ae53192 ("libertas_tf: main.c, data paths and mac80211 handlers")
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Link: https://patch.msgid.link/178211481807.2212567.8773346114561900100@maoyixie.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0b352f04b9be2c83c0240aa6dae7257fefa90464 ]
otx2vf_register_mbox_intr() currently installs the VF mailbox IRQ
handler before clearing stale mailbox interrupt state. The code then says
that local interrupt bits should be cleared first to avoid spurious
interrupts, but that clear still happens only after request_irq() has
already made the handler reachable.
A running system can reach this during VF mailbox interrupt registration
while stale or latched RVU_VF_INT state is still present. If delivery
happens in the request_irq()-to-clear window,
otx2vf_vfaf_mbox_intr_handler() can run before local quiesce and touch
the same vf->mbox and vf->mbox_wq carrier that probe and teardown later
reuse or destroy.
Move the stale mailbox interrupt clear ahead of request_irq(), but keep
interrupt enabling after the handler is installed. This closes the
pre-clear early-IRQ window without creating a new enable-before-handler
window.
Fixes: 3184fb5ba96e ("octeontx2-vf: Virtual function driver support")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ratheesh Kannoth <rkannoth@marvell.com>
Link: https://patch.msgid.link/20260611160014.3202224-3-runyu.xiao@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f918554fb7246e89b98ef90abe80801f038258b3 ]
otx2_register_mbox_intr() currently installs the PF mailbox IRQ handler
before clearing stale mailbox interrupt state. The function itself then
comments that the local interrupt bits must be cleared first to avoid
spurious interrupts, but that clear happens only after request_irq() has
already exposed the handler to irq delivery.
A running system can reach this during PF mailbox interrupt registration
while stale or latched RVU_PF_INT state is still present. If delivery
happens in the request_irq()-to-clear window,
otx2_pfaf_mbox_intr_handler() can run before local quiesce and touch
the same pf->mbox and pf->mbox_wq carrier that probe and teardown later
reuse or destroy.
Move the stale mailbox interrupt clear ahead of request_irq(), but keep
interrupt enabling after the handler is installed. This closes the
pre-clear early-IRQ window without creating a new enable-before-handler
window.
Fixes: 5a6d7c9daef3 ("octeontx2-pf: Mailbox communication with AF")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ratheesh Kannoth <rkannoth@marvell.com>
Link: https://patch.msgid.link/20260611160014.3202224-2-runyu.xiao@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d0976b43956ee8c8bd093223df9115bfcf63dfe5 ]
This patch removes unnecessary typecasts by marking the
mbox_regions array as __iomem since it is used to store
pointers to memory-mapped I/O (MMIO) regions. Also simplified
the call to readq() in PF driver by removing redundant type casts.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/1749484309-3434-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: f918554fb724 ("octeontx2-pf: clear stale mailbox IRQ state before request_irq()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit def9a4745e105145133e442dd8a1c126caf0f553 upstream.
Commit 2a22b7ae2fa3 ("net: pcs: xpcs: adapt Wangxun NICs for SGMII mode")
added a path in xpcs_get_state_c37_sgmii() that reads speed/duplex from
BMCR after AN completes. However, BMCR does not reflect the negotiated
result on the hardware where this has been tested:
- On RK3568 (MAC side SGMII), BMCR returns a fixed hardware reset value
- Wangxun engineer Jiawen Wu confirmed that on their side, "BMCR looks
like it only wants to be return as 0" [0]
The correct information is available in CL37_ANSGM_STS, which contains
the actual link status and negotiated speed/duplex.
This bug was previously masked by phylink core, which overrides the PCS
link state with the PHY state when a PHY is present:
/* If we have a phy, the "up" state is the union of both the
* PHY and the MAC
*/
if (phy)
link_state.link &= pl->phy_state.link;
Thus, when the link is down, the PHY's link_down state is applied on top
of whatever the PCS reports, hiding the broken PCS state reading path.
Modify xpcs_get_state_c37_sgmii() to:
1. Read link state from CL37_ANSGM_STS
2. If link is up, report speed/duplex from CL37_ANSGM_STS
3. Remove the broken BMCR reading path entirely
Also properly set state->an_complete to reflect the AN completion status,
and clear CL37_ANCMPLT_INTR when link is down to avoid stale state.
[0] https://lore.kernel.org/all/000c01dd1593$2ac0b0f0$804212d0$@trustnetic.com/
Fixes: 2a22b7ae2fa3 ("net: pcs: xpcs: adapt Wangxun NICs for SGMII mode")
Cc: stable@vger.kernel.org
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260717074324.3250043-2-coiaprant@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9fcdb1c3c4ba134434694c001dbff343f1ffa319 ]
The 'command' and 'netdev_ops' debugfs files are a legacy debugging
interface supported by the i40e driver since its early days by commit
02e9c290814c ("i40e: debugfs interface").
Both of these debugfs files provide a read handler which is mostly useless,
and which is implemented with questionable logic. They both use a static
256 byte buffer which is initialized to the empty string. In the case of
the 'command' file this buffer is literally never used and simply wastes
space. In the case of the 'netdev_ops' file, the last command written is
saved here.
On read, the files contents are presented as the name of the device
followed by a colon and then the contents of their respective static
buffer. For 'command' this will always be "<device>: ". For 'netdev_ops',
this will be "<device>: <last command written>". But note the buffer is
shared between all devices operated by this module. At best, it is mostly
meaningless information, and at worse it could be accessed simultaneously
as there doesn't appear to be any locking mechanism.
We have also recently received multiple reports for both read functions
about their use of snprintf and potential overflow that could result in
reading arbitrary kernel memory. For the 'command' file, this is
definitely impossible, since the static buffer is always zero and never
written to. For the 'netdev_ops' file, it does appear to be possible, if
the user carefully crafts the command input, it will be copied into the
buffer, which could be large enough to cause snprintf to truncate, which
then causes the copy_to_user to read beyond the length of the buffer
allocated by kzalloc.
A minimal fix would be to replace snprintf() with scnprintf() which would
cap the return to the number of bytes written, preventing an overflow. A
more involved fix would be to drop the mostly useless static buffers,
saving 512 bytes and modifying the read functions to stop needing those as
input.
Instead, lets just completely drop the read access to these files. These
are debug interfaces exposed as part of debugfs, and I don't believe that
dropping read access will break any script, as the provided output is
pretty useless. You can find the netdev name through other more standard
interfaces, and the 'netdev_ops' interface can easily result in garbage if
you issue simultaneous writes to multiple devices at once.
In order to properly remove the i40e_dbg_netdev_ops_buf, we need to
refactor its write function to avoid using the static buffer. Instead, use
the same logic as the i40e_dbg_command_write, with an allocated buffer.
Update the code to use this instead of the static buffer, and ensure we
free the buffer on exit. This fixes simultaneous writes to 'netdev_ops' on
multiple devices, and allows us to remove the now unused static buffer
along with removing the read access.
Fixes: 02e9c290814c ("i40e: debugfs interface")
Reported-by: Kunwu Chan <chentao@kylinos.cn>
Closes: https://lore.kernel.org/intel-wired-lan/20231208031950.47410-1-chentao@kylinos.cn/
Reported-by: Wang Haoran <haoranwangsec@gmail.com>
Closes: https://lore.kernel.org/all/CANZ3JQRRiOdtfQJoP9QM=6LS1Jto8PGBGw6y7-TL=BcnzHQn1Q@mail.gmail.com/
Reported-by: Amir Mohammad Jahangirzad <a.jahangirzad@gmail.com>
Closes: https://lore.kernel.org/all/20250722115017.206969-1-a.jahangirzad@gmail.com/
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kunwu Chan <kunwu.chan@linux.dev>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
[Adapted to 6.6: context conflict due to 6.6 using pf->vsi[pf->lan_vsi]
vs i40e_pf_get_main_vsi(pf) in the removed read functions; resolution
is simply to delete the 6.6 version of those functions.]
Signed-off-by: Jay Wang <wanjay@amazon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit dcd9b465965422b9654f6026e8a2fa8984f74c3c upstream.
When replacing the source list of an MDB remote entry, all existing
sources are first marked for deletion and vxlan_mdb_remote_srcs_add()
is then called to add the new source list. Sources present in the new
list have their deletion mark cleared, and any sources left marked
afterwards are removed.
If vxlan_mdb_remote_srcs_add() fails partway through, its error path
deletes all entries on the remote's source list. That rollback is only
correct for its other caller, vxlan_mdb_remote_add(), where the remote
was just allocated and the list contains solely entries added during
the call. On the replace path the list also holds pre-existing sources,
so a failed replace tears them down together with their (S, G)
forwarding entries instead of leaving the entry unchanged.
This is reachable from an existing (*, G) remote. An EXCLUDE filter
that loses sources starts forwarding traffic that should be blocked,
while an INCLUDE filter that loses sources drops traffic that should be
forwarded.
Mark entries created during the current pass with a new
VXLAN_SGRP_F_NEW flag. On failure, delete only those entries and clear
the deletion mark on the pre-existing ones, so a failed replace leaves
the source list untouched. Retain the flag until the whole operation
succeeds and then clear it. Also stop vxlan_mdb_remote_src_add() from
deleting a pre-existing entry it only looked up when adding that
entry's forwarding entry fails.
Fixes: a3a48de5eade ("vxlan: mdb: Add MDB control path support")
Cc: stable@vger.kernel.org
Signed-off-by: James Raphael Tiovalen <jamestiotio@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260720160428.249356-1-jamestiotio@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
