| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking fixes from David Miller:
"Here is a quick pull request primarily meant to address the deconfig
fallout from changing SCSI_NETLINK from being used via 'select' to
being used via 'depends'.
I applied a set of 5 patches written by Michal Marek, and then I
carefully audited all of the remaining config files, basically:
1) I scanned every arch config file, and if it mentioned CONFIG_INET
or CONFIG_UNIX, I made sure it had CONFIG_NET=y
2) After that, I scanned every arch config file, and if it did not
have CONFIG_NET=y I made sure it did not reference any networking
config options.
Finally, we have some late breaking wireless fixes in here from John
Linville and co"
[ And there's a sparc bpf fix snuck in too ]
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sparc: bpf_jit: fix loads from negative offsets
parisc: Update defconfigs which were missing CONFIG_NET.
powerpc: Update defconfigs which were missing CONFIG_NET.
s390: Update defconfigs which were missing CONFIG_NET.
mips: Update some more defconfigs which were missing CONFIG_NET.
sparc: Set CONFIG_NET=y in defconfigs
sh: Set CONFIG_NET=y in defconfigs
powerpc: Set CONFIG_NET=y in defconfigs
parisc: Set CONFIG_NET=y in defconfigs
mips: Set CONFIG_NET=y in defconfigs
brcmfmac: Fix off by one bug in brcmf_count_20mhz_channels()
ath9k: Fix NULL pointer dereference on early irq
net: rfkill: gpio: Fix clock status
NFC: st21nfca: Fix potential depmod dependency cycle
NFC: st21nfcb: Fix depmod dependency cycle
NFC: microread: Potential overflows in microread_target_discovered()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-23
Please consider pulling this one last batch of fixes intended for the 3.17 stream!
For the NFC bits, Samuel says:
"Hopefully not too late for a handful of NFC fixes:
- 2 potential build failures for ST21NFCA and ST21NFCB, triggered by a
depmod dependenyc cycle.
- One potential buffer overflow in the microread driver."
On top of that...
Emil Goode provides a fix for a brcmfmac off-by-one regression which
was introduced in the 3.17 cycle.
Loic Poulain fixes a polarity mismatch for a variable assignment
inside of rfkill-gpio.
Wojciech Dubowik prevents a NULL pointer dereference in ath9k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Last late set of InfiniBand/RDMA fixes for 3.17:
- fixes for the new memory region re-registration support
- iSER initiator error path fixes
- grab bag of small fixes for the qib and ocrdma hardware drivers
- larger set of fixes for mlx4, especially in RoCE mode"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
IB/mlx4: Fix VF mac handling in RoCE
IB/mlx4: Do not allow APM under RoCE
IB/mlx4: Don't update QP1 in native mode
IB/mlx4: Avoid accessing netdevice when building RoCE qp1 header
mlx4: Fix mlx4 reg/unreg mac to work properly with 0-mac addresses
IB/core: When marshaling uverbs path, clear unused fields
IB/mlx4: Avoid executing gid task when device is being removed
IB/mlx4: Fix lockdep splat for the iboe lock
IB/mlx4: Get upper dev addresses as RoCE GIDs when port comes up
IB/mlx4: Reorder steps in RoCE GID table initialization
IB/mlx4: Don't duplicate the default RoCE GID
IB/mlx4: Avoid null pointer dereference in mlx4_ib_scan_netdevs()
IB/iser: Bump version to 1.4.1
IB/iser: Allow bind only when connection state is UP
IB/iser: Fix RX/TX CQ resource leak on error flow
RDMA/ocrdma: Use right macro in query AH
RDMA/ocrdma: Resolve L2 address when creating user AH
mlx4: Correct error flows in rereg_mr
IB/qib: Correct reference counting in debugfs qp_stats
IPoIB: Remove unnecessary port query
...
|
|
In the brcmf_count_20mhz_channels function we are looping through a list
of channels received from firmware. Since the index of the first channel
is 0 the condition leads to an off by one bug. This is causing us to hit
the WARN_ON_ONCE(1) calls in the brcmu_d11n_decchspec function, which is
how I discovered the bug.
Introduced by:
commit b48d891676f756d48b4d0ee131e4a7a5d43ca417
("brcmfmac: rework wiphy structure setup")
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We should not be manipulaging the DMA_CTRL registers directly by writing
0 to them to disable DMA. This is an operation that needs to be timed to
make sure the DMA engines have been properly stopped since their state
machine stops on a packet boundary, not immediately.
Make sure that tha bcmgenet_fini_dma() calls bcmgenet_dma_teardown() to
ensure a proper DMA engine state. As a result, we need to reorder the
function bodies to resolve the use dependency.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GENET driver supports SKB fragments, and succeeds in transmitting
them properly, but when reclaiming these transmitted fragments, we will
only update the count of free buffer descriptors by 1, even for SKBs
with fragments. This leads to the networking stack thinking it has more
room than the hardware has when pushing new SKBs, and backing off
consequently because we return NETDEV_TX_BUSY.
Fix this by accounting for the SKB nr_frags plus one (itself) and update
ring->free_bds accordingly with that value for each iteration loop in
__bcmgenet_tx_reclaim().
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In one error condition dm9000_parse_dt() returns NULL, however the
return value is checked using IS_ERR() in dm9000_probe(), leading to the
error not being properly propagated if CONFIG_OF is not enabled or the
device tree data is not available. Fix this by also returning an
ERR_PTR() in this case.
Fixes: 0b8bf1baabe5 (net: dm9000: Allow instantiation using device tree)
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ah struct might not have been initialized when
interrupt comes so check for it.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is an extra semi-colon so __rtl8169_set_features() is called every
time.
Fixes: 929a031dfd62 ('r8169: adjust __rtl8169_set_features')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the hw is in ALDPS mode, the hw may have no response for accessing
the most registers. Therefore, the ALDPS should be disabled before
accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(),
and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw
wouldn't enter ALDPS mode when linking on. The hw would enter the
ALDPS mode after several seconds when link down occurs and the ALDPS
is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TG3 appears to have an issue performing TSO and checksum offloading
correclty when the frame has been vlan encapsulated (non-accelrated).
In these cases, tcp checksum is not correctly updated.
This patch attempts to work around this issue. After the patch,
802.1ad vlans start working correctly over tg3 devices.
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 412ca1550cbe ("macvlan: Move broadcasts into a work queue"), the
driver uses tx_queue_len of the master device as the limit of packets enqueuing.
Problem is that virtual drivers have this value set to 0, thus all broadcast
packets were rejected.
Because tx_queue_len was arbitrarily chosen, I replace it with a static limit
of 1000 (also arbitrarily chosen).
CC: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Thibaut Collet <thibaut.collet@6wind.com>
Suggested-by: Thibaut Collet <thibaut.collet@6wind.com>
Tested-by: Thibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following randconfig build failure:
> drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c: In function
> ‘pch_ptp_match’:
> drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c:130:2: error:
> implicit declaration of function ‘ptp_classify_raw’
> [-Werror=implicit-function-declaration]
> if (ptp_classify_raw(skb) == PTP_CLASS_NONE)
> ^
> cc1: some warnings being treated as errors
> make[5]: *** [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.o] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a chance that the VF mlx4 RoCE driver (mlx4_ib) may see a 0-mac
as the current default MAC address when a RoCE interface first comes up.
In this case, the RoCE driver registers the 0-mac to get its MAC index --
used in the INIT2RTR transition when it creates its proxy Q1 qp's.
If we do not allow QP1 to be created, the RoCE driver will not come up.
If we do not register the 0-mac, but simply use a random mac-index,
QP1 will attempt to send packets with an someone's else source MAC which
will get the system into more troubled.
Since a 0-mac was previously used to indicate a free slot, this leads to
errors, both when the 0-mac is registered and when it is unregistered.
The required fix is to check in addition that the slot containing the
0-mac has a reference count of zero.
Additionally, when comparing MAC addresses, need to mask out the 2 MSBs
of the u64 mac on both sides of the comparison.
Note that when the EN driver (mlx4_en) comes up, it set itself a proper
mac --> the RoCE driver gets to be notified on that and further handing
is done with the update qp command, as was added by commit 9433c188915c
("IB/mlx4: Invoke UPDATE_QP for proxy QP1 on MAC changes").
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This patch addresses feedback from Sagi Grimberg on the rereg_mr
implementation of mlx4. The following are fixed:
1. Set the correct pd_flags
2. Make sure we change the iova and size MR fields only after
successful write and allocation of the MTTs.
3. Make the error checking more robust
Fixes: e630664c8383 ("mlx4_core: Add helper functions to support MR re-registration")
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-09-18
this is a pull request of 8 patches for current net.
A patch by Roger Quadros for the c_can driver fixes the swapped parameters of
the c_can_hw_raminit_ti() function. Oliver Hartkopp adds the missing PCI ids to
the peak_pci driver to support the single channel PCAN ExpressCard 34 adapter.
David Dueck converts the at91_can driver to use proper clock handling
functions. Then there are 5 patches by David Jander and me which fix several
mailbox related problems in the flexcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I cannot move a macvlan interface created on top of a bonding interface
to a different namespace:
% ip netns add dummy0
% ip link add link bond0 mac0 type macvlan
% ip link set mac0 netns dummy0
RTNETLINK answers: Invalid argument
%
The problem seems to be that commit f9399814927a ("bonding: Don't allow
bond devices to change network namespaces.") sets NETIF_F_NETNS_LOCAL
on bonding interfaces, and commit 797f87f83b60 ("macvlan: fix netdev
feature propagation from lower device") causes macvlan interfaces
to inherit its features from the lower device.
NETIF_F_NETNS_LOCAL should not be inherited from the lower device
by a macvlan.
Patch tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-17
Please pull this batch of fixes intended for the 3.17 stream...
Arend van Spriel sends a trio of minor brcmfmac fixes, including a
fix for a Kconfig/build issue, a fix for a crash (null reference),
and a regression fix related to event handling on a P2P interface.
Hante Meuleman follows-up with a brcmfmac fix for a memory leak.
Johannes Stezenbach brings an ath9k_htc fix for a regression related
to hardware decryption offload.
Marcel Holtmann delivers a one-liner to properly mark a device ID
table in rfkill-gpio.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently aded the use of skb_frag_dma_map to 3c59x, but didn't realize it
automatically included the frag_offset internally, as well as provided an option
to specify an extra offset in the parameter list. We need to specify an offset
of 0 in the parameter list to avoid skb corruption that results in lost
connections.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Linux Kernel list <linux-kernel@vger.kernel.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
|
|
Noted that 3c59x has no checks on transmit for failed DMA mappings, and no
ability to unmap fragments when a single map fails in the middle of a transmit.
This patch provides error checking to ensure that dma mappings work properly,
and unrolls an skb mapping if a fragmented skb transmission has a mapping
failure to prevent leaks.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Linux Kernel list <linux-kernel@vger.kernel.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
|
|
In order to make the driver work with the common clock framework, this patch
converts the clk_enable()/clk_disable() to
clk_prepare_enable()/clk_disable_unprepare(). While there, add the missing
error handling.
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch increases the mask in the FLEXCAN_MCR_MAXMB() to 7 bits as in the
newer flexcan cores the MAXMB field is 7 bits wide.
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
After sending a RTR frame the TX mailbox becomes a RX_EMPTY mailbox. To avoid
side effects when the RX-FIFO is full, this patch puts the TX mailbox into
TX_INACTIVE mode in the transmission complete interrupt handler. This, of
course, leaves a race window between the actual completion of the transmission
and the handling of tx-complete interrupt. However this is the best we can do
without busy polling the tx complete interrupt.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch implements the workaround mentioned in ERR005829:
ERR005829: FlexCAN: FlexCAN does not transmit a message that is enabled to
be transmitted in a specific moment during the arbitration process.
Workaround: The workaround consists of two extra steps after setting up a
message for transmission:
Step 8: Reserve the first valid mailbox as an inactive mailbox (CODE=0b1000).
If RX FIFO is disabled, this mailbox must be message buffer 0. Otherwise, the
first valid mailbox can be found using the "RX FIFO filters" table in the
FlexCAN chapter of the chip reference manual.
Step 9: Write twice INACTIVE code (0b1000) into the first valid mailbox.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Apparently mailboxes may contain random data at startup, causing some of them
being prepared for message reception. This causes overruns being missed or even
confusing the IRQ check for trasmitted messages, increasing the transmit
counter instead of the error counter.
This patch initializes all mailboxes after the FIFO as RX_INACTIVE.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes the initialization of the TX mailbox. It is now correctly
initialized as TX_INACTIVE not RX_EMPTY.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add PCI ID definition for the single channel PCAN ExpressCard 34 adapter. Due
to the subsystem id evaluation the correct number of channels (here 1) is
created at initialization time. Tested including the LED functionality.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Pass the correct 'mask' and 'value' bits to c_can_hw_raminit_wait_ti(). They
seem to have been swapped in the usage instances.
Reported-by: Jay Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Reported by Nikolay Aleksandrov. In efx_init_port() we call
efx_mac_reconfigure() to work around a Falcon/A1 limitation, and this calls
efx_{arch}_filter_sync_rx_mode(), which takes the addr_list_lock; but this
lock is uninitialised, because we haven't called register_netdevice() yet.
So, in efx_farch_filter_sync_rx_mode(), check efx_dev_registered() before
doing anything else.
The EF10 equivalent, efx_ef10_filter_sync_rx_mode(), already has the
corresponding check.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Tested-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the "changed" test in __rtl8169_set_features(). Instead, do
simple test in rtl8169_set_features().
Set the RxChkSum and RxVlan through __rtl8169_set_features() in
rtl_open().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 35b1de557970 ("rdma/cxgb4: Fixes cxgb4 probe failure in VM when PF is
exposed through PCI Passthrough") moved the code to check for SR-IOV PF[0..3]
much further down in init_one() past the point where we allocate a (struct
adapter) for PF[0..3]. As a result, we left four of these on ever module remove.
Fix: Allocate adapter structure only for PF4
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In v3.15 the driver stopped to accept network packets after successful
authentification, which could be worked around by passing the
nohwcrypt=1 module parameter. This was not reproducible by
everyone, and showed random behaviour in some tests.
It was caused by an uninitialized variable introduced
in 4ed1a8d4a257 ("ath9k_htc: use ath9k_cmn_rx_accept") and
used in 341b29b9cd2f ("ath9k_htc: use ath9k_cmn_rx_skb_postprocess").
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=78581
Fixes: 341b29b9cd2f ("ath9k_htc: use ath9k_cmn_rx_skb_postprocess")
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The firmware notifies about interface changes through the IF event
which has a NO_IF flag that means host can ignore the event. This
behaviour was introduced in the driver by:
commit 2ee8382fc6c763c76396a6aaff77a27089eed3aa
Author: Arend van Spriel <arend@broadcom.com>
Date: Sat Aug 10 12:27:24 2013 +0200
brcmfmac: ignore IF event if firmware indicates it
It turns out that the IF event for the P2P_DEVICE also has this
flag set, but the event should not be ignored in this scenario.
The mentioned commit caused a regression in 3.12 kernel in creation
of the P2P_DEVICE interface.
Cc: <stable@vger.kernel.org> # 3.14, 3.16
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For P2P_DEVICE interface the function brcmf_cfg80211_update_proto_addr_mode()
resulted in a crash, because it assumed wdev->netdev would be valid. The
ifp should be obtained through the driver vif structure which contains the
wireless_dev.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The host-interface can select which protocol implementation it
needs. Selecting PCIe will include the msgbuf protocol and selecting
USB and/or SDIO will include the bcdc protocol. The PCIe kconfig
option assures the dependencies for msgbuf are met, ie. HAS_DMA.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The function brcmf_enable_bw40_2g contains a memory leak. The
function is also missing initialisation of one of the members of
ch struct, which can lead to warning but this has no impact on
result.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The KSZ9031 appears to suffer from the same hardware bug as described
for the KSZ9021 in commit 32fcafbcd1c9f6c7013016a22a5369b4acb93577
("net/phy: micrel: Disable asymmetric pause for KSZ9021")
you have to unplug the cable and plug it back to get it to work.
Remove the SUPPORTED_Asym_Pause flag for the KSZ9031 to fix this.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The problem is that the slave is first linked and slave_cnt is
incremented afterwards leading to a div by zero in the modes that use it
as a modulus. What happens is that in bond_start_xmit()
bond_has_slaves() is used to evaluate further transmission and it becomes
true after the slave is linked in, but when slave_cnt is used in the xmit
path it is still 0, so fetch it once and transmit based on that. Since
it is used only in round-robin and XOR modes, the fix is only for them.
Thanks to Eric Dumazet for pointing out the fault in my first try to fix
this.
Call trace (took it out of net-next kernel, but it's the same with net):
[46934.330038] divide error: 0000 [#1] SMP
[46934.330041] Modules linked in: bonding(O) 9p fscache
snd_hda_codec_generic crct10dif_pclmul
[46934.330041] bond0: Enslaving eth1 as an active interface with an up
link
[46934.330051] ppdev joydev crc32_pclmul crc32c_intel 9pnet_virtio
ghash_clmulni_intel snd_hda_intel 9pnet snd_hda_controller parport_pc
serio_raw pcspkr snd_hda_codec parport virtio_balloon virtio_console
snd_hwdep snd_pcm pvpanic i2c_piix4 snd_timer i2ccore snd soundcore
virtio_blk virtio_net virtio_pci virtio_ring virtio ata_generic
pata_acpi floppy [last unloaded: bonding]
[46934.330053] CPU: 1 PID: 3382 Comm: ping Tainted: G O
3.17.0-rc4+ #27
[46934.330053] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[46934.330054] task: ffff88005aebf2c0 ti: ffff88005b728000 task.ti:
ffff88005b728000
[46934.330059] RIP: 0010:[<ffffffffa0198c33>] [<ffffffffa0198c33>]
bond_start_xmit+0x1c3/0x450 [bonding]
[46934.330060] RSP: 0018:ffff88005b72b7f8 EFLAGS: 00010246
[46934.330060] RAX: 0000000000000679 RBX: ffff88004b077000 RCX:
000000000000002a
[46934.330061] RDX: 0000000000000000 RSI: ffff88004b3f0500 RDI:
ffff88004b077940
[46934.330061] RBP: ffff88005b72b830 R08: 00000000000000c0 R09:
ffff88004a83e000
[46934.330062] R10: 000000000000ffff R11: ffff88004b1f12c0 R12:
ffff88004b3f0500
[46934.330062] R13: ffff88004b3f0500 R14: 000000000000002a R15:
ffff88004b077940
[46934.330063] FS: 00007fbd91a4c740(0000) GS:ffff88005f080000(0000)
knlGS:0000000000000000
[46934.330064] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[46934.330064] CR2: 00007f803a8bb000 CR3: 000000004b2c9000 CR4:
00000000000406e0
[46934.330069] Stack:
[46934.330071] ffffffff811e6169 00000000e772fa05 ffff88004b077000
ffff88004b3f0500
[46934.330072] ffffffff81d17d18 000000000000002a 0000000000000000
ffff88005b72b8a0
[46934.330073] ffffffff81620108 ffffffff8161fe0e ffff88005b72b8c4
ffff88005b302000
[46934.330073] Call Trace:
[46934.330077] [<ffffffff811e6169>] ?
__kmalloc_node_track_caller+0x119/0x300
[46934.330084] [<ffffffff81620108>] dev_hard_start_xmit+0x188/0x410
[46934.330086] [<ffffffff8161fe0e>] ? harmonize_features+0x2e/0x90
[46934.330088] [<ffffffff81620b06>] __dev_queue_xmit+0x456/0x590
[46934.330089] [<ffffffff81620c50>] dev_queue_xmit+0x10/0x20
[46934.330090] [<ffffffff8168f022>] arp_xmit+0x22/0x60
[46934.330091] [<ffffffff8168f090>] arp_send.part.16+0x30/0x40
[46934.330092] [<ffffffff8168f1e5>] arp_solicit+0x115/0x2b0
[46934.330094] [<ffffffff8160b5d7>] ? copy_skb_header+0x17/0xa0
[46934.330096] [<ffffffff8162875a>] neigh_probe+0x4a/0x70
[46934.330097] [<ffffffff8162979c>] __neigh_event_send+0xac/0x230
[46934.330098] [<ffffffff8162a00b>] neigh_resolve_output+0x13b/0x220
[46934.330100] [<ffffffff8165f120>] ? ip_forward_options+0x1c0/0x1c0
[46934.330101] [<ffffffff81660478>] ip_finish_output+0x1f8/0x860
[46934.330102] [<ffffffff81661f08>] ip_output+0x58/0x90
[46934.330103] [<ffffffff81661602>] ? __ip_local_out+0xa2/0xb0
[46934.330104] [<ffffffff81661640>] ip_local_out_sk+0x30/0x40
[46934.330105] [<ffffffff81662a66>] ip_send_skb+0x16/0x50
[46934.330106] [<ffffffff81662ad3>] ip_push_pending_frames+0x33/0x40
[46934.330107] [<ffffffff8168854c>] raw_sendmsg+0x88c/0xa30
[46934.330110] [<ffffffff81612b31>] ? skb_recv_datagram+0x41/0x60
[46934.330111] [<ffffffff816875a9>] ? raw_recvmsg+0xa9/0x1f0
[46934.330113] [<ffffffff816978d4>] inet_sendmsg+0x74/0xc0
[46934.330114] [<ffffffff81697a9b>] ? inet_recvmsg+0x8b/0xb0
[46934.330115] bond0: Adding slave eth2
[46934.330116] [<ffffffff8160357c>] sock_sendmsg+0x9c/0xe0
[46934.330118] [<ffffffff81603248>] ?
move_addr_to_kernel.part.20+0x28/0x80
[46934.330121] [<ffffffff811b4477>] ? might_fault+0x47/0x50
[46934.330122] [<ffffffff816039b9>] ___sys_sendmsg+0x3a9/0x3c0
[46934.330125] [<ffffffff8144a14a>] ? n_tty_write+0x3aa/0x530
[46934.330127] [<ffffffff810d1ae4>] ? __wake_up+0x44/0x50
[46934.330129] [<ffffffff81242b38>] ? fsnotify+0x238/0x310
[46934.330130] [<ffffffff816048a1>] __sys_sendmsg+0x51/0x90
[46934.330131] [<ffffffff816048f2>] SyS_sendmsg+0x12/0x20
[46934.330134] [<ffffffff81738b29>] system_call_fastpath+0x16/0x1b
[46934.330144] Code: 48 8b 10 4c 89 ee 4c 89 ff e8 aa bc ff ff 31 c0 e9
1a ff ff ff 0f 1f 00 4c 89 ee 4c 89 ff e8 65 fb ff ff 31 d2 4c 89 ee 4c
89 ff <f7> b3 64 09 00 00 e8 02 bd ff ff 31 c0 e9 f2 fe ff ff 0f 1f 00
[46934.330146] RIP [<ffffffffa0198c33>] bond_start_xmit+0x1c3/0x450
[bonding]
[46934.330146] RSP <ffff88005b72b7f8>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
Fixes: 278b208375 ("bonding: initial RCU conversion")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The setting should depend on the new features not the current one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the parameter "features" of __rtl8169_set_features() is equal to
dev->features, the variable "changed" is alwayes 0, and nothing would
be changed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During suspend and resume in Dual EMAC, second port is not working as in
suspend/resume only the first slave netdev is closed and opened. So bring
down and up all the interfaces that are up during suspend/resume.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nstat->multicast refers to received packets, not transmitted as
is returned here. Change it so that received packet stats are
given.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-11
Please pull this batch of fixes intended for the 3.17 stream:
For the mac80211 bits, Johannes says:
"Two more fixes for mac80211 - one of them addresses a long-standing
issue that we only found when using vendor events more frequently;
the other addresses some bad information being reported in userspace
that people were starting to actually look at."
For the iwlwifi bits, Emmanuel says:
"I re-enable scheduled scan on firmware that contain the fix for
the bug that Linus reported. A few trivial fixes: endianity issues,
the same DTIM period fix that I did in mac80211. Eyal fixes a few
issues we identified with EAPOL, we now send them just as if they were
management frames, this solves interrop issues. Johannes has another
set of trivial fixes, while Luca fixes the way we configure the filters
in the firmware. Last but not least, a new device is added by Oren."
Emmanuel was traveling, resulting in his pull to be a bit larger than
I would have liked to see at this point. FWIW, I have asked Emmanuel
to be much more strict for any more pull requests in this cycle.
In addition to the above, Sujith Manoharan reverts an earlier ath9k
patch. The earlier change was found to allow for the device to sleep
too long and miss beacons.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-09-11
this is a pull request for the current release cycle of a single patch.
The patch by David Jander fixes a scheduling while atomic problem in the
flexcan driver, that was introduced by me in v3.14-rc6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the logic in tx path to ensure that tx descriptors
are reused for transmission only after they have been reclaimed by
arc_emac_tx_clean().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current implementation the cleaning of tx ring is done by the
NAPI poll handler, which is scheduled after rx interrupts. Thus, in
absence of received packets the reclaim of used tx buffers is never
executed, blocking further transmission.
This can be easily reproduced starting the transmission of a UDP flow
with iperf, which blocks almost immediately because skbs are not
returned to the stack and the socket send buffer becomes full.
The patch enables tx interrupts so that the tx reclaim is scheduled
after completed transmissions.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 09ebb810927a110e4c354beb20308830d108a54b.
ath9k_hw_set_sta_beacon_timers() configures AR_TIM_PERIOD with
the beacon interval. Before this commit, the sleepduration was
never greater than the beacon interval. But now, the behavior
has changed. For example, with an AP that uses a beacon interval of 100:
ath: phy9: next beacon 61128704
ath: phy9: beacon period 204800
ath: phy9: DTIM period 204800
If the sleepduration is calculated based on the listen time, then
the bmiss threshold should also be changed since the HW would
be in sleep state for a longer time, but that is not done currently.
To avoid configuring a higher beacon interval based on the sleepduration,
revert to the original behavior. Power consumption is not a
problem since PS is disabled in ath9k anyway.
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Apparently can_restart() runs from a (timer-) interrupt and can call
flexcan_chip_[en|dis]able(), so avoid using usleep_range()
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Changing the vlan stripping policy of the QP isn't supported by older
firmware versions for the INIT2RTR command. Nevertheless, we've used it.
Fix that by doing this policy change using INIT2RTR only if the firmware
supports it, otherwise, we call UPDATE_QP command to do the task.
Fixes: 7677fc9 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current wrapper implementation of the UPDATE_QP command tries to get
the MAC index, even if MAC wasn't set by the VF. Fix it up to only handle
the MAC field if it's valid.
Fixes: ce8d9e0 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
