| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 881a0263d502e1a93ebc13a78254e9ad19520232 upstream.
Quanyang observed that when using an NFS rootfs on an AMD ZynqMp board,
the rootfs may take an extended time to recover after a suspend.
Upon investigation, it was determined that the issue originates from a
problem in the macb driver.
According to the Zynq UltraScale TRM [1], when transmit is disabled,
the transmit buffer queue pointer resets to point to the address
specified by the transmit buffer queue base address register.
In the current implementation, the code merely resets `queue->tx_head`
and `queue->tx_tail` to '0'. This approach presents several issues:
- Packets already queued in the tx ring are silently lost,
leading to memory leaks since the associated skbs cannot be released.
- Concurrent write access to `queue->tx_head` and `queue->tx_tail` may
occur from `macb_tx_poll()` or `macb_start_xmit()` when these values
are reset to '0'.
- The transmission may become stuck on a packet that has already been sent
out, with its 'TX_USED' bit set, but has not yet been processed. However,
due to the manipulation of 'queue->tx_head' and 'queue->tx_tail',
`macb_tx_poll()` incorrectly assumes there are no packets to handle
because `queue->tx_head == queue->tx_tail`. This issue is only resolved
when a new packet is placed at this position. This is the root cause of
the prolonged recovery time observed for the NFS root filesystem.
To resolve this issue, shuffle the tx ring and tx skb array so that
the first unsent packet is positioned at the start of the tx ring.
Additionally, ensure that updates to `queue->tx_head` and
`queue->tx_tail` are properly protected with the appropriate lock.
[1] https://docs.amd.com/v/u/en-US/ug1085-zynq-ultrascale-trm
Fixes: bf9cf80cab81 ("net: macb: Fix tx/rx malfunction after phy link down and up")
Reported-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260307-zynqmp-v2-1-6ef98a70e1d0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99c8c16a4aad0b37293cae213e15957c573cf79b upstream.
If request_threaded_irq() fails during the PTP message IRQ setup, the
newly created IRQ mapping is never disposed. Indeed, the
ksz_ptp_irq_setup()'s error path only frees the mappings that were
successfully set up.
Dispose the newly created mapping if the associated
request_threaded_irq() fails at setup.
Cc: stable@vger.kernel.org
Fixes: d0b8fec8ae505 ("net: dsa: microchip: Fix symetry in ksz_ptp_msg_irq_{setup/free}()")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20260309-ksz-ptp-irq-fix-v1-1-757b3b985955@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2503d08f8a2de618e5c3a8183b250ff4a2e2d52c upstream.
Normal RX/TX interrupts are enabled later, in arc_emac_open(), so probe
should not see interrupt delivery in the usual case. However, hardware may
still present stale or latched interrupt status left by firmware or the
bootloader.
If probe later unwinds after devm_request_irq() has installed the handler,
such a stale interrupt can still reach arc_emac_intr() during teardown and
race with release of the associated net_device.
Avoid that window by putting the device into a known quiescent state before
requesting the IRQ: disable all EMAC interrupt sources and clear any
pending EMAC interrupt status bits. This keeps the change hardware-focused
and minimal, while preventing spurious IRQ delivery from leftover state.
Fixes: e4f2379db6c6 ("ethernet/arc/arc_emac - Add new driver")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Link: https://patch.msgid.link/20260309132409.584966-1-fanwu01@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 224a0d284c3caf1951302d1744a714784febed71 upstream.
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
This driver takes a reference to the USB device during probe but does
not to release it on probe failures.
Drop the redundant device reference to fix the leak, reduce cargo
culting, make it easier to spot drivers where an extra reference is
needed, and reduce the risk of further memory leaks.
Fixes: 0791c0327a6e ("net: mctp: Add MCTP USB transport driver")
Cc: stable@vger.kernel.org # 6.15
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260305104549.16110-1-johan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fb4903b3354aed4a2301180cf991226f896c87ed upstream.
Executing ethtool -m can fail reporting a netlink I/O error while firmware
link management holds the i2c bus used to communicate with the module.
According to Intel(R) Ethernet Controller E810 Datasheet Rev 2.8 [1]
Section 3.3.10.4 Read/Write SFF EEPROM (0x06EE)
request should to be retried upon receiving EBUSY from firmware.
Commit e9c9692c8a81 ("ice: Reimplement module reads used by ethtool")
implemented it only for part of ice_get_module_eeprom(), leaving all other
calls to ice_aq_sff_eeprom() vulnerable to returning early on getting
EBUSY without retrying.
Remove the retry loop from ice_get_module_eeprom() and add Admin Queue
(AQ) command with opcode 0x06EE to the list of commands that should be
retried on receiving EBUSY from firmware.
Cc: stable@vger.kernel.org
Fixes: e9c9692c8a81 ("ice: Reimplement module reads used by ethtool")
Signed-off-by: Jakub Staniszewski <jakub.staniszewski@linux.intel.com>
Co-developed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://www.intel.com/content/www/us/en/content-details/613875/intel-ethernet-controller-e810-datasheet.html [1]
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dabffd08545ffa1d7183bc45e387860984025291 upstream.
MANA hardware requires at least one doorbell ring every 8 wraparounds
of the CQ. The driver rings the doorbell as a form of flow control to
inform hardware that CQEs have been consumed.
The NAPI poll functions mana_poll_tx_cq() and mana_poll_rx_cq() can
poll up to CQE_POLLING_BUFFER (512) completions per call. If the CQ
has fewer than 512 entries, a single poll call can process more than
4 wraparounds without ringing the doorbell. The doorbell threshold
check also uses ">" instead of ">=", delaying the ring by one extra
CQE beyond 4 wraparounds. Combined, these issues can cause the driver
to exceed the 8-wraparound hardware limit, leading to missed
completions and stalled queues.
Fix this by capping the number of CQEs polled per call to 4 wraparounds
of the CQ in both TX and RX paths. Also change the doorbell threshold
from ">" to ">=" so the doorbell is rung as soon as 4 wraparounds are
reached.
Cc: stable@vger.kernel.org
Fixes: 58a63729c957 ("net: mana: Fix doorbell out of order violation and avoid unnecessary doorbell rings")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260226192833.1050807-1-longli@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit feae40a6a178bb525a15f19288016e5778102a99 upstream.
It may happen that VF spawned for E610 adapter has problem with setting
link up. This happens when ixgbevf supporting mailbox API 1.6 cooperates
with PF driver which doesn't support this version of API, and hence
doesn't support new approach for getting PF link data.
In that case VF asks PF to provide link data but as PF doesn't support
it, returns -EOPNOTSUPP what leads to early bail from link configuration
sequence.
Avoid such situation by using legacy VFLINKS approach whenever negotiated
API version is less than 1.6.
To reproduce the issue just create VF and set its link up - adapter must
be any from the E610 family, ixgbevf must support API 1.6 or higher while
ixgbevf must not.
Fixes: 53f0eb62b4d2 ("ixgbevf: fix getting link speed data for E610 devices")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 326256c0a72d4877cec1d4df85357da106233128 upstream.
Add retry mechanism for indirect Admin Queue (AQ) commands. To do so we
need to keep the command buffer.
This technically reverts commit 43a630e37e25
("ice: remove unused buffer copy code in ice_sq_send_cmd_retry()"),
but combines it with a fix in the logic by using a kmemdup() call,
making it more robust and less likely to break in the future due to
programmer error.
Cc: Michal Schmidt <mschmidt@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 3056df93f7a8 ("ice: Re-send some AQ commands, as result of EBUSY AQ error")
Signed-off-by: Jakub Staniszewski <jakub.staniszewski@linux.intel.com>
Co-developed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9cc0e440f0664f6f3e2c26e39ab9dd5f3badba7 upstream.
Do not configure Latency Tolerance Messaging (LTM) on USB 2.0 hardware.
The LAN7850 is a High-Speed (USB 2.0) only device and does not support
SuperSpeed features like LTM. Currently, the driver unconditionally
attempts to configure LTM registers during initialization. On the
LAN7850, these registers do not exist, resulting in writes to invalid
or undocumented memory space.
This issue was identified during a port to the regmap API with strict
register validation enabled. While no functional issues or crashes have
been observed from these invalid writes, bypassing LTM initialization
on the LAN7850 ensures the driver strictly adheres to the hardware's
valid register map.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 312c816c6bc30342bc30dca0d6db617ab4d3ae4e upstream.
Remove redundant netif_napi_del() call from disconnect path.
A WARN may be triggered in __netif_napi_del_locked() during USB device
disconnect:
WARNING: CPU: 0 PID: 11 at net/core/dev.c:7417 __netif_napi_del_locked+0x2b4/0x350
This happens because netif_napi_del() is called in the disconnect path while
NAPI is still enabled. However, it is not necessary to call netif_napi_del()
explicitly, since unregister_netdev() will handle NAPI teardown automatically
and safely. Removing the redundant call avoids triggering the warning.
Full trace:
lan78xx 1-1:1.0 enu1: Failed to read register index 0x000000c4. ret = -ENODEV
lan78xx 1-1:1.0 enu1: Failed to set MAC down with error -ENODEV
lan78xx 1-1:1.0 enu1: Link is Down
lan78xx 1-1:1.0 enu1: Failed to read register index 0x00000120. ret = -ENODEV
------------[ cut here ]------------
WARNING: CPU: 0 PID: 11 at net/core/dev.c:7417 __netif_napi_del_locked+0x2b4/0x350
Modules linked in: flexcan can_dev fuse
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 6.16.0-rc2-00624-ge926949dab03 #9 PREEMPT
Hardware name: SKOV IMX8MP CPU revC - bd500 (DT)
Workqueue: usb_hub_wq hub_event
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __netif_napi_del_locked+0x2b4/0x350
lr : __netif_napi_del_locked+0x7c/0x350
sp : ffffffc085b673c0
x29: ffffffc085b673c0 x28: ffffff800b7f2000 x27: ffffff800b7f20d8
x26: ffffff80110bcf58 x25: ffffff80110bd978 x24: 1ffffff0022179eb
x23: ffffff80110bc000 x22: ffffff800b7f5000 x21: ffffff80110bc000
x20: ffffff80110bcf38 x19: ffffff80110bcf28 x18: dfffffc000000000
x17: ffffffc081578940 x16: ffffffc08284cee0 x15: 0000000000000028
x14: 0000000000000006 x13: 0000000000040000 x12: ffffffb0022179e8
x11: 1ffffff0022179e7 x10: ffffffb0022179e7 x9 : dfffffc000000000
x8 : 0000004ffdde8619 x7 : ffffff80110bcf3f x6 : 0000000000000001
x5 : ffffff80110bcf38 x4 : ffffff80110bcf38 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 1ffffff0022179e7 x0 : 0000000000000000
Call trace:
__netif_napi_del_locked+0x2b4/0x350 (P)
lan78xx_disconnect+0xf4/0x360
usb_unbind_interface+0x158/0x718
device_remove+0x100/0x150
device_release_driver_internal+0x308/0x478
device_release_driver+0x1c/0x30
bus_remove_device+0x1a8/0x368
device_del+0x2e0/0x7b0
usb_disable_device+0x244/0x540
usb_disconnect+0x220/0x758
hub_event+0x105c/0x35e0
process_one_work+0x760/0x17b0
worker_thread+0x768/0xce8
kthread+0x3bc/0x690
ret_from_fork+0x10/0x20
irq event stamp: 211604
hardirqs last enabled at (211603): [<ffffffc0828cc9ec>] _raw_spin_unlock_irqrestore+0x84/0x98
hardirqs last disabled at (211604): [<ffffffc0828a9a84>] el1_dbg+0x24/0x80
softirqs last enabled at (211296): [<ffffffc080095f10>] handle_softirqs+0x820/0xbc8
softirqs last disabled at (210993): [<ffffffc080010288>] __do_softirq+0x18/0x20
---[ end trace 0000000000000000 ]---
lan78xx 1-1:1.0 enu1: failed to kill vid 0081/0
Fixes: e110bc825897 ("net: usb: lan78xx: Convert to PHYLINK for improved PHY and MAC management")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 50988747c30df47b73b787f234f746027cb7ec6c upstream.
Account for hardware auto-padding in TX byte counters to reflect actual
wire traffic.
The LAN7850 hardware automatically pads undersized frames to the minimum
Ethernet frame length (ETH_ZLEN, 60 bytes). However, the driver tracks
the network statistics based on the unpadded socket buffer length. This
results in the tx_bytes counter under-reporting the actual physical
bytes placed on the Ethernet wire for small packets (like short ARP or
ICMP requests).
Use max_t() to ensure the transmission statistics accurately account for
the hardware-generated padding.
Fixes: d383216a7efe ("lan78xx: Introduce Tx URB processing improvements")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4f774a0cc955ce762aec91c66915a6e15087ab7 upstream.
Do not drop packets with checksum errors at the USB driver level;
pass them to the network stack.
Previously, the driver dropped all packets where the 'Receive Error
Detected' (RED) bit was set, regardless of the specific error type. This
caused packets with only IP or TCP/UDP checksum errors to be dropped
before reaching the kernel, preventing the network stack from accounting
for them or performing software fallback.
Add a mask for hard hardware errors to safely drop genuinely corrupt
frames, while allowing checksum-errored frames to pass with their
ip_summed field explicitly set to CHECKSUM_NONE.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2df6162785f31f1bbb598cfc3b08e4efc88f80b6 upstream.
So far the driver populated the struct can_priv::do_set_bittiming() and
struct can_priv::fd::do_set_data_bittiming() callbacks.
Before bringing up the interface, user space has to configure the bitrates.
With these callbacks the configuration is directly forwarded into the CAN
hardware. Then the interface can be brought up.
An ifdown-ifup cycle (without changing the bit rates) doesn't re-configure
the bitrates in the CAN hardware. This leads to a problem with the
CANable-2.5 [1] firmware, which resets the configured bit rates during
ifdown.
To fix the problem remove both bit timing callbacks and always configure
the bitrates in the struct net_device_ops::ndo_open() callback.
[1] https://github.com/Elmue/CANable-2.5-firmware-Slcan-and-Candlelight
Cc: stable@vger.kernel.org
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://patch.msgid.link/20260219-gs_usb-always-configure-bitrates-v2-1-671f8ba5b0a5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 87f7dff3ec75b91def0024ebaaf732457f47a63b ]
The NIX RAS health report path uses nix_af_rvu_err when handling the
NIX_AF_RVU_RAS case, so the report prints the ERR interrupt status rather
than the RAS interrupt status.
Use nix_af_rvu_ras for the NIX_AF_RVU_RAS report.
Fixes: 5ed66306eab6 ("octeontx2-af: Add devlink health reporters for NIX")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://patch.msgid.link/20260310184824.1183651-2-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc26ca99b835e21e76a58b1463b84adb0ca34f58 ]
The NIX RAS health reporter recovery routine checks nix_af_rvu_int to
decide whether to re-enable NIX_AF_RAS interrupts. This is the RVU
interrupt status field and is unrelated to RAS events, so the recovery
flow may incorrectly skip re-enabling NIX_AF_RAS interrupts.
Check nix_af_rvu_ras instead before writing NIX_AF_RAS_ENA_W1S.
Fixes: 5ed66306eab6 ("octeontx2-af: Add devlink health reporters for NIX")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://patch.msgid.link/20260310184824.1183651-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 840c9d13cb1ca96683a5307ee8e221be163a2c1e ]
The "rx_filter" member of "hwtstamp_config" structure is an enum field and
does not support bitwise OR combination of multiple filter values. It
causes error while linuxptp application tries to match rx filter version.
Fix this by storing the requested filter type in a new port field.
Fixes: 97248adb5a3b ("net: ti: am65-cpsw: Update hw timestamping filter for PTPv1 RX packets")
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://patch.msgid.link/20260310160940.109822-1-c-vankar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 87c2302813abc55c46485711a678e3c312b00666 ]
In mana_gd_setup() error path, set gc->service_wq to NULL after
destroy_workqueue() to match the cleanup in mana_gd_cleanup().
This prevents a use-after-free if the workqueue pointer is checked
after a failed setup.
Fixes: f975a0955276 ("net: mana: Fix double destroy_workqueue on service rescan PCI path")
Signed-off-by: Shiraz Saleem <shirazsaleem@microsoft.com>
Signed-off-by: Konstantin Taranov <kotaranov@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260309172443.688392-1-kotaranov@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8f0dc024ce55451ebd54bad975134ba802e4fcc ]
The rtl8366rb_led_group_port_mask() function always returns LED port
bit in LED group 0; the switch statement returns the same thing in all
non-default cases.
This means that the driver does not currently support configuring LEDs
in non-zero LED groups.
Fix this.
Fixes: 32d617005475a71e ("net: dsa: realtek: add LED drivers for rtl8366rb")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260311111237.29002-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 30021e969d48e5819d5ae56936c2f34c0f7ce997 ]
When booting with the 'ipv6.disable=1' parameter, the nd_tbl is never
initialized because inet6_init() exits before ndisc_init() is called
which initializes it. If bonding ARP/NS validation is enabled, an IPv6
NS/NA packet received on a slave can reach bond_validate_na(), which
calls bond_has_this_ip6(). That path calls ipv6_chk_addr() and can
crash in __ipv6_chk_addr_and_flags().
BUG: kernel NULL pointer dereference, address: 00000000000005d8
Oops: Oops: 0000 [#1] SMP NOPTI
RIP: 0010:__ipv6_chk_addr_and_flags+0x69/0x170
Call Trace:
<IRQ>
ipv6_chk_addr+0x1f/0x30
bond_validate_na+0x12e/0x1d0 [bonding]
? __pfx_bond_handle_frame+0x10/0x10 [bonding]
bond_rcv_validate+0x1a0/0x450 [bonding]
bond_handle_frame+0x5e/0x290 [bonding]
? srso_alias_return_thunk+0x5/0xfbef5
__netif_receive_skb_core.constprop.0+0x3e8/0xe50
? srso_alias_return_thunk+0x5/0xfbef5
? update_cfs_rq_load_avg+0x1a/0x240
? srso_alias_return_thunk+0x5/0xfbef5
? __enqueue_entity+0x5e/0x240
__netif_receive_skb_one_core+0x39/0xa0
process_backlog+0x9c/0x150
__napi_poll+0x30/0x200
? srso_alias_return_thunk+0x5/0xfbef5
net_rx_action+0x338/0x3b0
handle_softirqs+0xc9/0x2a0
do_softirq+0x42/0x60
</IRQ>
<TASK>
__local_bh_enable_ip+0x62/0x70
__dev_queue_xmit+0x2d3/0x1000
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? packet_parse_headers+0x10a/0x1a0
packet_sendmsg+0x10da/0x1700
? kick_pool+0x5f/0x140
? srso_alias_return_thunk+0x5/0xfbef5
? __queue_work+0x12d/0x4f0
__sys_sendto+0x1f3/0x220
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x101/0xf80
? exc_page_fault+0x6e/0x170
? srso_alias_return_thunk+0x5/0xfbef5
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
Fix this by checking ipv6_mod_enabled() before dispatching IPv6 packets to
bond_na_rcv(). If IPv6 is disabled, return early from bond_rcv_validate()
and avoid the path to ipv6_chk_addr().
Suggested-by: Fernando Fernandez Mancera <fmancera@suse.de>
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Signed-off-by: Ricardo B. Marlière <rbm@suse.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20260307-net-nd_tbl_fixes-v4-2-e2677e85628c@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 908c344d5cfac4160f49715da9efacdf5b6a28bd ]
The bcmgenet EEE implementation is broken in several ways.
phy_support_eee() is never called, so the PHY never advertises EEE
and phylib never sets phydev->enable_tx_lpi. bcmgenet_mac_config()
checks priv->eee.eee_enabled to decide whether to enable the MAC
LPI logic, but that field is never initialised to true, so the MAC
never enters Low Power Idle even when EEE is negotiated - wasting
the power savings EEE is designed to provide. The only way to get
EEE working at all is a manual 'ethtool --set-eee eth0 eee on' after
every link-up, and even then bcmgenet_get_eee() immediately clobbers
the reported state because phy_ethtool_get_eee() overwrites
eee_enabled and tx_lpi_enabled with the uninitialised PHY eee_cfg
values. Finally, bcmgenet_mac_config() is only called on link-up,
so EEE is never disabled in hardware on link-down.
Fix all of this by removing the MAC-side EEE state tracking
(priv->eee) and aligning with the pattern used by other non-phylink
MAC drivers such as FEC.
Call phy_support_eee() in bcmgenet_mii_probe() so the PHY advertises
EEE link modes and phylib tracks negotiation state. Move the EEE
hardware control to bcmgenet_mii_setup(), which is called on every
link event, and drive it directly from phydev->enable_tx_lpi - the
flag phylib sets when EEE is negotiated and the user has not disabled
it. This enables EEE automatically once the link partner agrees and
disables it cleanly on link-down.
Make bcmgenet_get_eee() and bcmgenet_set_eee() pure passthroughs to
phy_ethtool_get_eee() and phy_ethtool_set_eee(), with the MAC
hardware register read/written for tx_lpi_timer. Drop struct
ethtool_keee eee from struct bcmgenet_priv.
Fixes: fe0d4fd9285e ("net: phy: Keep track of EEE configuration")
Link: https://lore.kernel.org/netdev/d352039f-4cbb-41e6-9aeb-0b4f3941b54c@lunn.ch/
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260310054935.1238594-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e94eaef11142b01f77bf8ba4d0b59720b7858109 ]
If an error is encountered while mapping TX buffers, the driver should
unmap any buffers already mapped for that skb.
Because count is incremented after a successful mapping, it will always
match the correct number of unmappings needed when dma_error is reached.
Decrementing count before the while loop in dma_error causes an
off-by-one error. If any mapping was successful before an unsuccessful
mapping, exactly one DMA mapping would leak.
In these commits, a faulty while condition caused an infinite loop in
dma_error:
Commit 03b1320dfcee ("e1000e: remove use of skb_dma_map from e1000e
driver")
Commit 602c0554d7b0 ("e1000: remove use of skb_dma_map from e1000 driver")
Commit c1fa347f20f1 ("e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of
unsigned in *_tx_map()") fixed the infinite loop, but introduced the
off-by-one error.
This issue may still exist in the igbvf driver, but I did not address it
in this patch.
Fixes: c1fa347f20f1 ("e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of unsigned in *_tx_map()")
Assisted-by: Claude:claude-4.6-opus
Signed-off-by: Matt Vollrath <tactii@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e809085f492842ce7a519c9ef72d40f4bca89c13 ]
Fix following issues in the IPv4 and IPv6 cloud filter handling logic in
both the add and delete paths:
- The source-IP mask check incorrectly compares mask.src_ip[0] against
tcf.dst_ip[0]. Update it to compare against tcf.src_ip[0]. This likely
goes unnoticed because the check is in an "else if" path that only
executes when dst_ip is not set, most cloud filter use cases focus on
destination-IP matching, and the buggy condition can accidentally
evaluate true in some cases.
- memcpy() for the IPv4 source address incorrectly uses
ARRAY_SIZE(tcf.dst_ip) instead of ARRAY_SIZE(tcf.src_ip), although
both arrays are the same size.
- The IPv4 memcpy operations used ARRAY_SIZE(tcf.dst_ip) and ARRAY_SIZE
(tcf.src_ip), Update these to use sizeof(cfilter->ip.v4.dst_ip) and
sizeof(cfilter->ip.v4.src_ip) to ensure correct and explicit copy size.
- In the IPv6 delete path, memcmp() uses sizeof(src_ip6) when comparing
dst_ip6 fields. Replace this with sizeof(dst_ip6) to make the intent
explicit, even though both fields are struct in6_addr.
Fixes: e284fc280473 ("i40e: Add and delete cloud filter")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fdadbf6e84c44df8dbb85cfdd38bc10e4431501d ]
Three driver callbacks schedule a reset and wait for its completion:
ndo_change_mtu(), ethtool set_ringparam(), and ethtool set_channels().
Waiting for reset in ndo_change_mtu() and set_ringparam() was added by
commit c2ed2403f12c ("iavf: Wait for reset in callbacks which trigger
it") to fix a race condition where adding an interface to bonding
immediately after MTU or ring parameter change failed because the
interface was still in __RESETTING state. The same commit also added
waiting in iavf_set_priv_flags(), which was later removed by commit
53844673d555 ("iavf: kill "legacy-rx" for good").
Waiting in set_channels() was introduced earlier by commit 4e5e6b5d9d13
("iavf: Fix return of set the new channel count") to ensure the PF has
enough time to complete the VF reset when changing channel count, and to
return correct error codes to userspace.
Commit ef490bbb2267 ("iavf: Add net_shaper_ops support") added
net_shaper_ops to iavf, which required reset_task to use _locked NAPI
variants (napi_enable_locked, napi_disable_locked) that need the netdev
instance lock.
Later, commit 7e4d784f5810 ("net: hold netdev instance lock during
rtnetlink operations") and commit 2bcf4772e45a ("net: ethtool: try to
protect all callback with netdev instance lock") started holding the
netdev instance lock during ndo and ethtool callbacks for drivers with
net_shaper_ops.
Finally, commit 120f28a6f314 ("iavf: get rid of the crit lock")
replaced the driver's crit_lock with netdev_lock in reset_task, causing
incorrect behavior: the callback holds netdev_lock and waits for
reset_task, but reset_task needs the same lock:
Thread 1 (callback) Thread 2 (reset_task)
------------------- ---------------------
netdev_lock() [blocked on workqueue]
ndo_change_mtu() or ethtool op
iavf_schedule_reset()
iavf_wait_for_reset() iavf_reset_task()
waiting... netdev_lock() <- blocked
This does not strictly deadlock because iavf_wait_for_reset() uses
wait_event_interruptible_timeout() with a 5-second timeout. The wait
eventually times out, the callback returns an error to userspace, and
after the lock is released reset_task completes the reset. This leads to
incorrect behavior: userspace sees an error even though the configuration
change silently takes effect after the timeout.
Fix this by extracting the reset logic from iavf_reset_task() into a new
iavf_reset_step() function that expects netdev_lock to be already held.
The three callbacks now call iavf_reset_step() directly instead of
scheduling the work and waiting, performing the reset synchronously in
the caller's context which already holds netdev_lock. This eliminates
both the incorrect error reporting and the need for
iavf_wait_for_reset(), which is removed along with the now-unused
reset_waitqueue.
The workqueue-based iavf_reset_task() becomes a thin wrapper that
acquires netdev_lock and calls iavf_reset_step(), preserving its use
for PF-initiated resets.
The callbacks may block for several seconds while iavf_reset_step()
polls hardware registers, but this is acceptable since netdev_lock is a
per-device mutex and only serializes operations on the same interface.
v3:
- Remove netif_running() guard from iavf_set_channels(). Unlike
set_ringparam where descriptor counts are picked up by iavf_open()
directly, num_req_queues is only consumed during
iavf_reinit_interrupt_scheme() in the reset path. Skipping the reset
on a down device would silently discard the channel count change.
- Remove dead reset_waitqueue code (struct field, init, and all
wake_up calls) since iavf_wait_for_reset() was the only consumer.
Fixes: 120f28a6f314 ("iavf: get rid of the crit lock")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit efc54fb13d79117a825fef17364315a58682c7ec ]
Commit 7c01dbfc8a1c5f ("iavf: periodically cache PHC time") introduced a
worker to cache PHC time, but failed to stop it during reset or disable.
This creates a race condition where `iavf_reset_task()` or
`iavf_disable_vf()` free adapter resources (AQ) while the worker is still
running. If the worker triggers `iavf_queue_ptp_cmd()` during teardown, it
accesses freed memory/locks, leading to a crash.
Fix this by calling `iavf_ptp_release()` before tearing down the adapter.
This ensures `ptp_clock_unregister()` synchronously cancels the worker and
cleans up the chardev before the backing resources are destroyed.
Fixes: 7c01dbfc8a1c5f ("iavf: periodically cache PHC time")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd98c6204d1195973b1760fe45860863deb6200c ]
If CONFIG_IRDMA isn't enabled but there are ice NICs in the system, the
driver will prevent full devlink dev param show dump because its rdma get
callbacks return ENODEV and stop the dump. For example:
$ devlink dev param show
pci/0000:82:00.0:
name msix_vec_per_pf_max type generic
values:
cmode driverinit value 2
name msix_vec_per_pf_min type generic
values:
cmode driverinit value 2
kernel answers: No such device
Returning EOPNOTSUPP allows the dump to continue so we can see all devices'
devlink parameters.
Fixes: c24a65b6a27c ("iidc/ice/irdma: Update IDC to support multiple consumers")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a8ba129af46856112981c124850ec6a85a1c1ab6 ]
commit f93505f35745 ("amd-xgbe: let the MAC manage PHY PM") moved
xgbe_phy_reset() from xgbe_open() to xgbe_start(), placing it after
phy_start(). As a result, the PHY settings were being reset after the
PHY had already started.
Reorder the calls so that the PHY settings are reset before
phy_start() is invoked.
Fixes: f93505f35745 ("amd-xgbe: let the MAC manage PHY PM")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-4-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 27a4dd0c702b3b2b9cf2c045d100cc2fe8720b81 ]
When operating in 10GBASE-KR mode with auto-negotiation disabled and RX
adaptation enabled, CRC errors can occur during the RX adaptation
process. This happens because the driver continues transmitting and
receiving packets while adaptation is in progress.
Fix this by stopping TX/RX immediately when the link goes down and RX
adaptation needs to be re-triggered, and only re-enabling TX/RX after
adaptation completes and the link is confirmed up. Introduce a flag to
track whether TX/RX was disabled for adaptation so it can be restored
correctly.
This prevents packets from being transmitted or received during the RX
adaptation window and avoids CRC errors from corrupted frames.
The flag tracking the data path state is synchronized with hardware
state in xgbe_start() to prevent stale state after device restarts.
This ensures that after a restart cycle (where xgbe_stop disables
TX/RX and xgbe_start re-enables them), the flag correctly reflects
that the data path is active.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-3-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6485cb96be5cd0f4bf39554737ba11322cc9b053 ]
The link status bit is latched low to allow detection of momentary
link drops. If the status indicates that the link is already down,
read it again to obtain the current state.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-2-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 950803f7254721c1c15858fbbfae3deaaeeecb11 ]
kernel BUG at net/core/skbuff.c:2306!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:pskb_expand_head+0xa08/0xfe0 net/core/skbuff.c:2306
RSP: 0018:ffffc90004aff760 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff88807e3c8780 RCX: ffffffff89593e0e
RDX: ffff88807b7c4900 RSI: ffffffff89594747 RDI: ffff88807b7c4900
RBP: 0000000000000820 R08: 0000000000000005 R09: 0000000000000000
R10: 00000000961a63e0 R11: 0000000000000000 R12: ffff88807e3c8780
R13: 00000000961a6560 R14: dffffc0000000000 R15: 00000000961a63e0
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1a0ed8df0 CR3: 000000002d816000 CR4: 00000000003526f0
Call Trace:
<TASK>
ipgre_header+0xdd/0x540 net/ipv4/ip_gre.c:900
dev_hard_header include/linux/netdevice.h:3439 [inline]
packet_snd net/packet/af_packet.c:3028 [inline]
packet_sendmsg+0x3ae5/0x53c0 net/packet/af_packet.c:3108
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
____sys_sendmsg+0xa54/0xc30 net/socket.c:2592
___sys_sendmsg+0x190/0x1e0 net/socket.c:2646
__sys_sendmsg+0x170/0x220 net/socket.c:2678
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x106/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fe1a0e6c1a9
When a non-Ethernet device (e.g. GRE tunnel) is enslaved to a bond,
bond_setup_by_slave() directly copies the slave's header_ops to the
bond device:
bond_dev->header_ops = slave_dev->header_ops;
This causes a type confusion when dev_hard_header() is later called
on the bond device. Functions like ipgre_header(), ip6gre_header(),all use
netdev_priv(dev) to access their device-specific private data. When
called with the bond device, netdev_priv() returns the bond's private
data (struct bonding) instead of the expected type (e.g. struct
ip_tunnel), leading to garbage values being read and kernel crashes.
Fix this by introducing bond_header_ops with wrapper functions that
delegate to the active slave's header_ops using the slave's own
device. This ensures netdev_priv() in the slave's header functions
always receives the correct device.
The fix is placed in the bonding driver rather than individual device
drivers, as the root cause is bond blindly inheriting header_ops from
the slave without considering that these callbacks expect a specific
netdev_priv() layout.
The type confusion can be observed by adding a printk in
ipgre_header() and running the following commands:
ip link add dummy0 type dummy
ip addr add 10.0.0.1/24 dev dummy0
ip link set dummy0 up
ip link add gre1 type gre local 10.0.0.1
ip link add bond1 type bond mode active-backup
ip link set gre1 master bond1
ip link set gre1 up
ip link set bond1 up
ip addr add fe80::1/64 dev bond1
Fixes: 1284cd3a2b74 ("bonding: two small fixes for IPoIB support")
Suggested-by: Jay Vosburgh <jv@jvosburgh.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jiayuan Chen <jiayuan.chen@shopee.com>
Link: https://patch.msgid.link/20260306021508.222062-1-jiayuan.chen@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 47bba09b14fa21712398febf36cb14fd4fc3bded ]
In hi3110_open(), the return value of hi3110_power_enable() is not checked.
If power enable fails, the device may not function correctly, while the
driver still returns success.
Add a check for the return value and propagate the error accordingly.
Signed-off-by: Wenyuan Li <2063309626@qq.com>
Link: https://patch.msgid.link/tencent_B5E2E7528BB28AA8A2A56E16C49BD58B8B07@qq.com
Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver")
[mkl: adjust subject, commit message and jump label]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3f5e0f22cfc2371e7471c9fd5b4da78f9df7c69 ]
When 'midev->allow_rx' is false, the newly allocated skb isn't consumed
by netif_rx(), it needs to free the skb directly.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Link: https://patch.msgid.link/20260305143240.97592-1-haiyuewa@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dbe17e7783cb5d6451ff1217d0464865857e97e1 ]
Given that some platforms may use PHY address 0 (I suppose the PHY may
not treat address 0 as a broadcast address or default response address).
It is possible for some boards to connect multiple PHYs to the same
ENETC MAC, for example:
- a PHY with a non-zero address connects to ENETC MAC through SGMII
interface (selected via DTS_A)
- a PHY with address 0 connects to ENETC MAC through RGMII interface
(selected via DTS_B)
For the case where the ENETC port MDIO is used to manage the PHY, when
switching from DTS_A to DTS_B via soft reboot, LaBCR[MDIO_PHYAD_PRTAD]
must be updated to 0 because the NETCMIX block is not reset during soft
reboot. However, the current driver explicitly skips configuring address
0, causing LaBCR[MDIO_PHYAD_PRTAD] to retain its old value.
Therefore, remove the special-case skip of PHY address 0 so that valid
configurations using address 0 are properly supported.
Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage")
Fixes: 50bfd9c06f0f ("net: enetc: set external PHY address in IERB for i.MX94 ENETC")
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260305031211.904812-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 246953f33e8cf95621d6c00332e2780ce1594082 ]
The current netc_get_phy_addr() implementation falls back to PHY address
0 when the "mdio" node or the PHY child node is missing. On i.MX95, this
causes failures when a real PHY is actually assigned address 0 and is
managed through the EMDIO interface. Because the bit 0 of phy_mask will
be set, leading imx95_enetc_mdio_phyaddr_config() to return an error, and
the netc_blk_ctrl driver probe subsequently fails. Fix this by returning
-ENODEV when neither an "mdio" node nor any PHY node is present, it means
that ENETC port MDIO is not used to manage the PHY, so there is no need
to configure LaBCR[MDIO_PHYAD_PRTAD].
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Closes: https://lore.kernel.org/all/7825188.GXAFRqVoOG@steina-w
Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage")
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260305031211.904812-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d9a60a0618d255530ca56072c5f39eb58e1ed4a ]
When changing channels, the current check in bnxt_set_channels()
is not checking for non-default RSS contexts when the RSS table size
changes. The current check for IFF_RXFH_CONFIGURED is only sufficient
for the default RSS context. Expand the check to include the presence
of any non-default RSS contexts.
Allowing such change will result in incorrect configuration of the
context's RSS table when the table size changes.
Fixes: b3d0083caf9a ("bnxt_en: Support RSS contexts in ethtool .{get|set}_rxfh()")
Reported-by: Björn Töpel <bjorn@kernel.org>
Link: https://lore.kernel.org/netdev/20260303181535.2671734-1-bjorn@kernel.org/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260306225854.3575672-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 288598d80a068a0e9281de35bcb4ce495f189e2a ]
A reproducer triggers a KASAN slab-use-after-free in pty_write_room()
when caif_serial's TX path calls tty_write_room(). The faulting access
is on tty->link->port.
Hold an extra kref on tty->link for the lifetime of the caif_serial line
discipline: get it in ldisc_open() and drop it in ser_release(), and
also drop it on the ldisc_open() error path.
With this change applied, the reproducer no longer triggers the UAF in
my testing.
Link: https://gist.github.com/shuangpengbai/c898debad6bdf170a84be7e6b3d8707f
Link: https://lore.kernel.org/netdev/20260301220525.1546355-1-shuangpeng.kernel@gmail.com
Fixes: e31d5a05948e ("caif: tty's are kref objects so take a reference")
Signed-off-by: Shuangpeng Bai <shuangpeng.kernel@gmail.com>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Link: https://patch.msgid.link/20260306034006.3395740-1-shuangpeng.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 87d126852158467ab87d5cbc36ccfd3f15464a6c ]
With the current sfp_fixup_ignore_tx_fault() fixup we ignore the TX_FAULT
signal, but we also need to apply sfp_fixup_ignore_los() in order to be
able to communicate with the module even if the fiber isn't connected for
configuration purposes.
This is needed for all the MA5671a firmwares, excluding the FS modded
firmware.
Fixes: 2069624dac19 ("net: sfp: Add tx-fault workaround for Huawei MA5671A SFP ONT")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260306125139.213637-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 86292155bea578ebab0ca3b65d4d87ecd8a0e9ea ]
The DMA mappings were leaked on mapping error. Free them with the
existing emac_free_tx_buf() function.
Fixes: bfec6d7f2001 ("net: spacemit: Add K1 Ethernet MAC")
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Link: https://patch.msgid.link/20260305-k1-ethernet-more-fixes-v2-2-e4e434d65055@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3aa1417803c1833cbd5bacb7e6a6489a196f2519 ]
Even if we get a dma_mapping_error() while mapping an RX buffer, we
should still update rx_ring->head to ensure that the buffers we were
able to allocate and map are used. Fix this by breaking out to the
existing code after the loop, analogous to the existing handling for skb
allocation failure.
Fixes: bfec6d7f2001 ("net: spacemit: Add K1 Ethernet MAC")
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Link: https://patch.msgid.link/20260305-k1-ethernet-more-fixes-v2-1-e4e434d65055@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a6413e6f6c9d9bb9833324cb3753582f7bc0f2fa ]
XDP multi-buf programs can modify the layout of the XDP buffer when the
program calls bpf_xdp_pull_data() or bpf_xdp_adjust_tail(). The
referenced commit in the fixes tag corrected the assumption in the mlx5
driver that the XDP buffer layout doesn't change during a program
execution. However, this fix introduced another issue: the dropped
fragments still need to be counted on the driver side to avoid page
fragment reference counting issues.
Such issue can be observed with the
test_xdp_native_adjst_tail_shrnk_data selftest when using a payload of
3600 and shrinking by 256 bytes (an upcoming selftest patch): the last
fragment gets released by the XDP code but doesn't get tracked by the
driver. This results in a negative pp_ref_count during page release and
the following splat:
WARNING: include/net/page_pool/helpers.h:297 at mlx5e_page_release_fragmented.isra.0+0x4a/0x50 [mlx5_core], CPU#12: ip/3137
Modules linked in: [...]
CPU: 12 UID: 0 PID: 3137 Comm: ip Not tainted 6.19.0-rc3+ #12 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:mlx5e_page_release_fragmented.isra.0+0x4a/0x50 [mlx5_core]
[...]
Call Trace:
<TASK>
mlx5e_dealloc_rx_wqe+0xcb/0x1a0 [mlx5_core]
mlx5e_free_rx_descs+0x7f/0x110 [mlx5_core]
mlx5e_close_rq+0x50/0x60 [mlx5_core]
mlx5e_close_queues+0x36/0x2c0 [mlx5_core]
mlx5e_close_channel+0x1c/0x50 [mlx5_core]
mlx5e_close_channels+0x45/0x80 [mlx5_core]
mlx5e_safe_switch_params+0x1a5/0x230 [mlx5_core]
mlx5e_change_mtu+0xf3/0x2f0 [mlx5_core]
netif_set_mtu_ext+0xf1/0x230
do_setlink.isra.0+0x219/0x1180
rtnl_newlink+0x79f/0xb60
rtnetlink_rcv_msg+0x213/0x3a0
netlink_rcv_skb+0x48/0xf0
netlink_unicast+0x24a/0x350
netlink_sendmsg+0x1ee/0x410
__sock_sendmsg+0x38/0x60
____sys_sendmsg+0x232/0x280
___sys_sendmsg+0x78/0xb0
__sys_sendmsg+0x5f/0xb0
[...]
do_syscall_64+0x57/0xc50
This patch fixes the issue by doing page frag counting on all the
original XDP buffer fragments for all relevant XDP actions (XDP_TX ,
XDP_REDIRECT and XDP_PASS). This is basically reverting to the original
counting before the commit in the fixes tag.
As frag_page is still pointing to the original tail, the nr_frags
parameter to xdp_update_skb_frags_info() needs to be calculated
in a different way to reflect the new nr_frags.
Fixes: afd5ba577c10 ("net/mlx5e: RX, Fix generating skb from non-linear xdp_buff for legacy RQ")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Amery Hung <ameryhung@gmail.com>
Link: https://patch.msgid.link/20260305142634.1813208-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db25c42c2e1f9c0d136420fff5e5700f7e771a6f ]
XDP multi-buf programs can modify the layout of the XDP buffer when the
program calls bpf_xdp_pull_data() or bpf_xdp_adjust_tail(). The
referenced commit in the fixes tag corrected the assumption in the mlx5
driver that the XDP buffer layout doesn't change during a program
execution. However, this fix introduced another issue: the dropped
fragments still need to be counted on the driver side to avoid page
fragment reference counting issues.
The issue was discovered by the drivers/net/xdp.py selftest,
more specifically the test_xdp_native_tx_mb:
- The mlx5 driver allocates a page_pool page and initializes it with
a frag counter of 64 (pp_ref_count=64) and the internal frag counter
to 0.
- The test sends one packet with no payload.
- On RX (mlx5e_skb_from_cqe_mpwrq_nonlinear()), mlx5 configures the XDP
buffer with the packet data starting in the first fragment which is the
page mentioned above.
- The XDP program runs and calls bpf_xdp_pull_data() which moves the
header into the linear part of the XDP buffer. As the packet doesn't
contain more data, the program drops the tail fragment since it no
longer contains any payload (pp_ref_count=63).
- mlx5 device skips counting this fragment. Internal frag counter
remains 0.
- mlx5 releases all 64 fragments of the page but page pp_ref_count is
63 => negative reference counting error.
Resulting splat during the test:
WARNING: CPU: 0 PID: 188225 at ./include/net/page_pool/helpers.h:297 mlx5e_page_release_fragmented.isra.0+0xbd/0xe0 [mlx5_core]
Modules linked in: [...]
CPU: 0 UID: 0 PID: 188225 Comm: ip Not tainted 6.18.0-rc7_for_upstream_min_debug_2025_12_08_11_44 #1 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:mlx5e_page_release_fragmented.isra.0+0xbd/0xe0 [mlx5_core]
[...]
Call Trace:
<TASK>
mlx5e_free_rx_mpwqe+0x20a/0x250 [mlx5_core]
mlx5e_dealloc_rx_mpwqe+0x37/0xb0 [mlx5_core]
mlx5e_free_rx_descs+0x11a/0x170 [mlx5_core]
mlx5e_close_rq+0x78/0xa0 [mlx5_core]
mlx5e_close_queues+0x46/0x2a0 [mlx5_core]
mlx5e_close_channel+0x24/0x90 [mlx5_core]
mlx5e_close_channels+0x5d/0xf0 [mlx5_core]
mlx5e_safe_switch_params+0x2ec/0x380 [mlx5_core]
mlx5e_change_mtu+0x11d/0x490 [mlx5_core]
mlx5e_change_nic_mtu+0x19/0x30 [mlx5_core]
netif_set_mtu_ext+0xfc/0x240
do_setlink.isra.0+0x226/0x1100
rtnl_newlink+0x7a9/0xba0
rtnetlink_rcv_msg+0x220/0x3c0
netlink_rcv_skb+0x4b/0xf0
netlink_unicast+0x255/0x380
netlink_sendmsg+0x1f3/0x420
__sock_sendmsg+0x38/0x60
____sys_sendmsg+0x1e8/0x240
___sys_sendmsg+0x7c/0xb0
[...]
__sys_sendmsg+0x5f/0xb0
do_syscall_64+0x55/0xc70
The problem applies for XDP_PASS as well which is handled in a different
code path in the driver.
This patch fixes the issue by doing page frag counting on all the
original XDP buffer fragments for all relevant XDP actions (XDP_TX ,
XDP_REDIRECT and XDP_PASS). This is basically reverting to the original
counting before the commit in the fixes tag.
As frag_page is still pointing to the original tail, the nr_frags
parameter to xdp_update_skb_frags_info() needs to be calculated
in a different way to reflect the new nr_frags.
Fixes: 87bcef158ac1 ("net/mlx5e: RX, Fix generating skb from non-linear xdp_buff for striding RQ")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Cc: Amery Hung <ameryhung@gmail.com>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305142634.1813208-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1633111d69053512d099658d4a05fc736fab36b0 ]
In case of a TX error CQE, a recovery flow is triggered,
mlx5e_reset_txqsq_cc_pc() resets dma_fifo_cc to 0 but not dma_fifo_pc,
desyncing the DMA FIFO producer and consumer.
After recovery, the producer pushes new DMA entries at the old
dma_fifo_pc, while the consumer reads from position 0.
This causes us to unmap stale DMA addresses from before the recovery.
The DMA FIFO is a purely software construct with no HW counterpart.
At the point of reset, all WQEs have been flushed so dma_fifo_cc is
already equal to dma_fifo_pc. There is no need to reset either counter,
similar to how skb_fifo pc/cc are untouched.
Remove the 'dma_fifo_cc = 0' reset.
This fixes the following WARNING:
WARNING: CPU: 0 PID: 0 at drivers/iommu/dma-iommu.c:1240 iommu_dma_unmap_page+0x79/0x90
Modules linked in: mlx5_vdpa vringh vdpa bonding mlx5_ib mlx5_vfio_pci ipip mlx5_fwctl tunnel4 mlx5_core ib_ipoib geneve ip6_gre ip_gre gre nf_tables ip6_tunnel rdma_ucm ib_uverbs ib_umad vfio_pci vfio_pci_core act_mirred act_skbedit act_vlan vhost_net vhost tap ip6table_mangle ip6table_nat ip6table_filter ip6_tables iptable_mangle cls_matchall nfnetlink_cttimeout act_gact cls_flower sch_ingress vhost_iotlb iptable_raw tunnel6 vfio_iommu_type1 vfio openvswitch nsh rpcsec_gss_krb5 auth_rpcgss oid_registry xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat nf_nat xt_addrtype br_netfilter overlay zram zsmalloc rpcrdma ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_cm ib_core fuse [last unloaded: nf_tables]
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.13.0-rc5_for_upstream_min_debug_2024_12_30_21_33 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:iommu_dma_unmap_page+0x79/0x90
Code: 2b 4d 3b 21 72 26 4d 3b 61 08 73 20 49 89 d8 44 89 f9 5b 4c 89 f2 4c 89 e6 48 89 ef 5d 41 5c 41 5d 41 5e 41 5f e9 c7 ae 9e ff <0f> 0b 5b 5d 41 5c 41 5d 41 5e 41 5f c3 66 2e 0f 1f 84 00 00 00 00
Call Trace:
<IRQ>
? __warn+0x7d/0x110
? iommu_dma_unmap_page+0x79/0x90
? report_bug+0x16d/0x180
? handle_bug+0x4f/0x90
? exc_invalid_op+0x14/0x70
? asm_exc_invalid_op+0x16/0x20
? iommu_dma_unmap_page+0x79/0x90
? iommu_dma_unmap_page+0x2e/0x90
dma_unmap_page_attrs+0x10d/0x1b0
mlx5e_tx_wi_dma_unmap+0xbe/0x120 [mlx5_core]
mlx5e_poll_tx_cq+0x16d/0x690 [mlx5_core]
mlx5e_napi_poll+0x8b/0xac0 [mlx5_core]
__napi_poll+0x24/0x190
net_rx_action+0x32a/0x3b0
? mlx5_eq_comp_int+0x7e/0x270 [mlx5_core]
? notifier_call_chain+0x35/0xa0
handle_softirqs+0xc9/0x270
irq_exit_rcu+0x71/0xd0
common_interrupt+0x7f/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
Fixes: db75373c91b0 ("net/mlx5e: Recover Send Queue (SQ) from error state")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305142634.1813208-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 76324e4041c0efb4808702b05426d7a0a7d8df5b ]
The check on mlx5_esw_host_functions_enabled(esw->dev) for adding VF
peer miss rules is incorrect. These rules match traffic from peer's VFs,
so the local device's host function status is irrelevant. Remove this
check to ensure peer VF traffic is properly handled regardless of local
host configuration.
Also fix the PF peer miss rule deletion to be symmetric with the add
path, so only attempt to delete the rule if it was actually created.
Fixes: 520369ef43a8 ("net/mlx5: Support disabling host PFs")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305142634.1813208-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 24b2795f9683e092dc22a68f487e7aaaf2ddafea ]
When moving to switchdev mode when the device doesn't support IPsec,
we try to clean up the IPsec resources anyway which causes the crash
below, fix that by correctly checking for IPsec support before trying
to clean up its resources.
[27642.515799] WARNING: arch/x86/mm/fault.c:1276 at
do_user_addr_fault+0x18a/0x680, CPU#4: devlink/6490
[27642.517159] Modules linked in: xt_conntrack xt_MASQUERADE
ip6table_nat ip6table_filter ip6_tables iptable_nat nf_nat xt_addrtype
rpcsec_gss_krb5 auth_rpcgss oid_registry overlay mlx5_fwctl nfnetlink
zram zsmalloc mlx5_ib fuse rpcrdma rdma_ucm ib_uverbs ib_iser libiscsi
scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_core
ib_core
[27642.521358] CPU: 4 UID: 0 PID: 6490 Comm: devlink Not tainted
6.19.0-rc5_for_upstream_min_debug_2026_01_14_16_47 #1 NONE
[27642.522923] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[27642.524528] RIP: 0010:do_user_addr_fault+0x18a/0x680
[27642.525362] Code: ff 0f 84 75 03 00 00 48 89 ee 4c 89 e7 e8 5e b9 22
00 49 89 c0 48 85 c0 0f 84 a8 02 00 00 f7 c3 60 80 00 00 74 22 31 c9 eb
ae <0f> 0b 48 83 c4 10 48 89 ea 48 89 de 4c 89 f7 5b 5d 41 5c 41 5d
41
[27642.528166] RSP: 0018:ffff88810770f6b8 EFLAGS: 00010046
[27642.529038] RAX: 0000000000000000 RBX: 0000000000000002 RCX:
ffff88810b980f00
[27642.530158] RDX: 00000000000000a0 RSI: 0000000000000002 RDI:
ffff88810770f728
[27642.531270] RBP: 00000000000000a0 R08: 0000000000000000 R09:
0000000000000000
[27642.532383] R10: 0000000000000000 R11: 0000000000000000 R12:
ffff888103f3c4c0
[27642.533499] R13: 0000000000000000 R14: ffff88810770f728 R15:
0000000000000000
[27642.534614] FS: 00007f197c741740(0000) GS:ffff88856a94c000(0000)
knlGS:0000000000000000
[27642.535915] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[27642.536858] CR2: 00000000000000a0 CR3: 000000011334c003 CR4:
0000000000172eb0
[27642.537982] Call Trace:
[27642.538466] <TASK>
[27642.538907] exc_page_fault+0x76/0x140
[27642.539583] asm_exc_page_fault+0x22/0x30
[27642.540282] RIP: 0010:_raw_spin_lock_irqsave+0x10/0x30
[27642.541134] Code: 07 85 c0 75 11 ba ff 00 00 00 f0 0f b1 17 75 06 b8
01 00 00 00 c3 31 c0 c3 90 0f 1f 44 00 00 53 9c 5b fa 31 c0 ba 01 00 00
00 <f0> 0f b1 17 75 05 48 89 d8 5b c3 89 c6 e8 7e 02 00 00 48 89 d8
5b
[27642.543936] RSP: 0018:ffff88810770f7d8 EFLAGS: 00010046
[27642.544803] RAX: 0000000000000000 RBX: 0000000000000202 RCX:
ffff888113ad96d8
[27642.545916] RDX: 0000000000000001 RSI: ffff88810770f818 RDI:
00000000000000a0
[27642.547027] RBP: 0000000000000098 R08: 0000000000000400 R09:
ffff88810b980f00
[27642.548140] R10: 0000000000000001 R11: ffff888101845a80 R12:
00000000000000a8
[27642.549263] R13: ffffffffa02a9060 R14: 00000000000000a0 R15:
ffff8881130d8a40
[27642.550379] complete_all+0x20/0x90
[27642.551010] mlx5e_ipsec_disable_events+0xb6/0xf0 [mlx5_core]
[27642.552022] mlx5e_nic_disable+0x12d/0x220 [mlx5_core]
[27642.552929] mlx5e_detach_netdev+0x66/0xf0 [mlx5_core]
[27642.553822] mlx5e_netdev_change_profile+0x5b/0x120 [mlx5_core]
[27642.554821] mlx5e_vport_rep_load+0x419/0x590 [mlx5_core]
[27642.555757] ? xa_load+0x53/0x90
[27642.556361] __esw_offloads_load_rep+0x54/0x70 [mlx5_core]
[27642.557328] mlx5_esw_offloads_rep_load+0x45/0xd0 [mlx5_core]
[27642.558320] esw_offloads_enable+0xb4b/0xc90 [mlx5_core]
[27642.559247] mlx5_eswitch_enable_locked+0x34e/0x4f0 [mlx5_core]
[27642.560257] ? mlx5_rescan_drivers_locked+0x222/0x2d0 [mlx5_core]
[27642.561284] mlx5_devlink_eswitch_mode_set+0x5ac/0x9c0 [mlx5_core]
[27642.562334] ? devlink_rate_set_ops_supported+0x21/0x3a0
[27642.563220] devlink_nl_eswitch_set_doit+0x67/0xe0
[27642.564026] genl_family_rcv_msg_doit+0xe0/0x130
[27642.564816] genl_rcv_msg+0x183/0x290
[27642.565466] ? __devlink_nl_pre_doit.isra.0+0x160/0x160
[27642.566329] ? devlink_nl_eswitch_get_doit+0x290/0x290
[27642.567181] ? devlink_nl_pre_doit_parent_dev_optional+0x20/0x20
[27642.568147] ? genl_family_rcv_msg_dumpit+0xf0/0xf0
[27642.568966] netlink_rcv_skb+0x4b/0xf0
[27642.569629] genl_rcv+0x24/0x40
[27642.570215] netlink_unicast+0x255/0x380
[27642.570901] ? __alloc_skb+0xfa/0x1e0
[27642.571560] netlink_sendmsg+0x1f3/0x420
[27642.572249] __sock_sendmsg+0x38/0x60
[27642.572911] __sys_sendto+0x119/0x180
[27642.573561] ? __sys_recvmsg+0x5c/0xb0
[27642.574227] __x64_sys_sendto+0x20/0x30
[27642.574904] do_syscall_64+0x55/0xc10
[27642.575554] entry_SYSCALL_64_after_hwframe+0x4b/0x53
[27642.576391] RIP: 0033:0x7f197c85e807
[27642.577050] Code: c7 c0 ff ff ff ff eb be 66 2e 0f 1f 84 00 00 00 00
00 90 f3 0f 1e fa 80 3d 45 08 0d 00 00 41 89 ca 74 10 b8 2c 00 00 00 0f
05 <48> 3d 00 f0 ff ff 77 69 c3 55 48 89 e5 53 48 83 ec 38 44 89 4d
d0
[27642.579846] RSP: 002b:00007ffebd4e2248 EFLAGS: 00000202 ORIG_RAX:
000000000000002c
[27642.581082] RAX: ffffffffffffffda RBX: 000055cfcd9cd2a0 RCX:
00007f197c85e807
[27642.582200] RDX: 0000000000000038 RSI: 000055cfcd9cd490 RDI:
0000000000000003
[27642.583320] RBP: 00007ffebd4e2290 R08: 00007f197c942200 R09:
000000000000000c
[27642.584437] R10: 0000000000000000 R11: 0000000000000202 R12:
0000000000000000
[27642.585555] R13: 000055cfcd9cd490 R14: 00007ffebd4e45d1 R15:
000055cfcd9cd2a0
[27642.586671] </TASK>
[27642.587121] ---[ end trace 0000000000000000 ]---
[27642.587910] BUG: kernel NULL pointer dereference, address:
00000000000000a0
Fixes: 664f76be38a1 ("net/mlx5: Fix IPsec cleanup over MPV device")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305142634.1813208-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aed763abf0e905b4b8d747d1ba9e172961572f57 ]
esw->work_queue executes esw_functions_changed_event_handler ->
esw_vfs_changed_event_handler and acquires the devlink lock.
.eswitch_mode_set (acquires devlink lock in devlink_nl_pre_doit) ->
mlx5_devlink_eswitch_mode_set -> mlx5_eswitch_disable_locked ->
mlx5_eswitch_event_handler_unregister -> flush_workqueue deadlocks
when esw_vfs_changed_event_handler executes.
Fix that by no longer flushing the work to avoid the deadlock, and using
a generation counter to keep track of work relevance. This avoids an old
handler manipulating an esw that has undergone one or more mode changes:
- the counter is incremented in mlx5_eswitch_event_handler_unregister.
- the counter is read and passed to the ephemeral mlx5_host_work struct.
- the work handler takes the devlink lock and bails out if the current
generation is different than the one it was scheduled to operate on.
- mlx5_eswitch_cleanup does the final draining before destroying the wq.
No longer flushing the workqueue has the side effect of maybe no longer
cancelling pending vport_change_handler work items, but that's ok since
those are disabled elsewhere:
- mlx5_eswitch_disable_locked disables the vport eq notifier.
- mlx5_esw_vport_disable disarms the HW EQ notification and marks
vport->enabled under state_lock to false to prevent pending vport
handler from doing anything.
- mlx5_eswitch_cleanup destroys the workqueue and makes sure all events
are disabled/finished.
Fixes: f1bc646c9a06 ("net/mlx5: Use devl_ API in mlx5_esw_offloads_devlink_port_register")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305081019.1811100-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3348be7978f450ede0c308a4e8416ac716cf1015 ]
Before the fixed commit, we check slave->new_link during commit
state, which values are only BOND_LINK_{NOCHANGE, UP, DOWN}. After
the commit, we start using slave->link_new_state, which state also could
be BOND_LINK_{FAIL, BACK}.
For example, when we set updelay/downdelay, after a failover,
the slave->link_new_state could be set to BOND_LINK_{FAIL, BACK} in
bond_miimon_inspect(). And later in bond_miimon_commit(), it will treat
it as invalid and print an error, which would cause confusion for users.
[ 106.440254] bond0: (slave veth2): link status down for interface, disabling it in 200 ms
[ 106.440265] bond0: (slave veth2): invalid new link 1 on slave
[ 106.648276] bond0: (slave veth2): link status definitely down, disabling slave
[ 107.480271] bond0: (slave veth2): link status up, enabling it in 200 ms
[ 107.480288] bond0: (slave veth2): invalid new link 3 on slave
[ 107.688302] bond0: (slave veth2): link status definitely up, 10000 Mbps full duplex
Let's handle BOND_LINK_{FAIL, BACK} as valid link states.
Fixes: 1899bb325149 ("bonding: fix state transition issue in link monitoring")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20260304-b4-bond_updelay-v1-2-f72eb2e454d0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 45fc134bcfadde456639c1b1e206e6918d69a553 ]
After commit e0caeb24f538 ("net: bonding: update the slave array for broadcast mode"),
broadcast mode will also set all_slaves and usable_slaves during
bond_enslave(). But if we also set updelay, during enslave, the
slave init state will be BOND_LINK_BACK. And later
bond_update_slave_arr() will alloc usable_slaves but add nothing.
This will cause bond_miimon_inspect() to have ignore_updelay
always true. So the updelay will be always ignored. e.g.
[ 6.498368] bond0: (slave veth2): link status definitely down, disabling slave
[ 7.536371] bond0: (slave veth2): link status up, enabling it in 0 ms
[ 7.536402] bond0: (slave veth2): link status definitely up, 10000 Mbps full duplex
To fix it, we can either always call bond_update_slave_arr() on every
place when link changes. Or, let's just not set usable_slaves for
broadcast mode.
Fixes: e0caeb24f538 ("net: bonding: update the slave array for broadcast mode")
Reported-by: Liang Li <liali@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20260304-b4-bond_updelay-v1-1-f72eb2e454d0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f76a93241d71fbba8425e3967097b498c29264ed ]
rx_packets should report the number of frames successfully received:
unicast + multicast + broadcast. Subtracting ifOutDiscards (a TX
counter) is incorrect and can undercount RX packets. RX drops are
already reported via rx_dropped (e.g. etherStatsDropEvents), so
there is no need to adjust rx_packets.
This patch removes the subtraction of ifOutDiscards from rx_packets
in rtl8365mb_stats_update().
Link: https://lore.kernel.org/netdev/878777925.105015.1763423928520@mail.yahoo.com/
Fixes: 4af2950c50c8 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260303-realtek_namiltd_fix2-v1-1-bfa433d3401e@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f8e18abf183dbd636a8725532c7f5aa58957de84 ]
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects truesize instead of DMA
write size. Different assumptions in enetc driver configuration lead to
negative tailroom.
Set frag_size to the same value as frame_sz.
Fixes: 2768b2e2f7d2 ("net: enetc: register XDP RX queues with frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-9-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c69d22c6c46a1d792ba8af3d8d6356fdc0e6f538 ]
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects whole buffer size instead
of DMA write size. Different assumptions in i40e driver configuration lead
to negative tailroom.
Set frag_size to the same value as frame_sz in shared pages mode, use new
helper to set frag_size when AF_XDP ZC is active.
Fixes: a045d2f2d03d ("i40e: set xdp_rxq_info::frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-7-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8f497dc8a61429cc004720aa8e713743355d80cf ]
Current way of handling XDP RxQ info in i40e has a problem, where frag_size
is not updated when xsk_buff_pool is detached or when MTU is changed, this
leads to growing tail always failing for multi-buffer packets.
Couple XDP RxQ info registering with buffer allocations and unregistering
with cleaning the ring.
Fixes: a045d2f2d03d ("i40e: set xdp_rxq_info::frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-6-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
