| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 71cfa7c893a05d09e7dc14713b27a8309fd4a2db ]
Some Potron SFP+ XGSPON ONU sticks are shipped with different EEPROM
vendor ID and vendor name strings, but are otherwise functionally
identical to the existing "Potron SFP+ XGSPON ONU Stick" handled by
sfp_quirk_potron().
These modules, including units distributed under the "Better Internet"
branding, use the same UART pin assignment and require the same
TX_FAULT/LOS behaviour and boot delay. Re-use the existing Potron
quirk for this EEPROM variant.
Signed-off-by: Marcus Hughes <marcus.hughes@betterinternet.ltd>
Link: https://patch.msgid.link/20251207210355.333451-1-marcus.hughes@betterinternet.ltd
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b5bdabb5449b652122e43f507f73789041d4abe ]
The max buffer size of ENETC RX BD is 0xFFFF bytes, so if the PAGE_SIZE
is greater than 128K, ENETC_RXB_DMA_SIZE and ENETC_RXB_DMA_SIZE_XDP will
be greater than 0xFFFF, thus causing a build warning.
This will not cause any practical issues because ENETC is currently only
used on the ARM64 platform, and the max PAGE_SIZE is 64K. So this patch
is only for fixing the build warning that occurs when compiling ENETC
drivers for other platforms.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202601050637.kHEKKOG7-lkp@intel.com/
Fixes: e59bc32df2e9 ("net: enetc: correct the value of ENETC_RXB_TRUESIZE")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260107091204.1980222-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit afa27621a28af317523e0836dad430bec551eb54 ]
When asynchronously writing to the device registers and if usb_submit_urb()
fail, the code fail to release allocated to this point resources.
Fixes: 323b34963d11 ("drivers: net: usb: pegasus: fix control urb submission")
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Link: https://patch.msgid.link/20260106084821.3746677-1-petko.manolov@konsulko.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d83dddffe1904e4a576d11a541878850a8e64cd2 ]
This patch fixes the edge case behavior on ifup/ifdown and
linking/unlinking two netdevsim interfaces:
1. unlink two interfaces netdevsim1 and netdevsim2
2. ifdown netdevsim1
3. ifup netdevsim1
4. link two interfaces netdevsim1 and netdevsim2
5. (Now two interfaces are linked in terms of netdevsim peer, but
carrier state of the two interfaces remains DOWN.)
This inconsistent behavior is caused by the current implementation,
which only cares about the "link, then ifup" order, not "ifup, then
link" order. This patch fixes the inconsistency by calling
netif_carrier_on() when two netdevsim interfaces are linked.
This patch fixes buggy behavior on NetworkManager-based systems which
causes the netdevsim test to fail with the following error:
# timeout set to 600
# selftests: drivers/net/netdevsim: peer.sh
# 2025/12/25 00:54:03 socat[9115] W address is opened in read-write mode but only supports read-only
# 2025/12/25 00:56:17 socat[9115] W connect(7, AF=2 192.168.1.1:1234, 16): Connection timed out
# 2025/12/25 00:56:17 socat[9115] E TCP:192.168.1.1:1234: Connection timed out
# expected 3 bytes, got 0
# 2025/12/25 00:56:17 socat[9109] W exiting on signal 15
not ok 13 selftests: drivers/net/netdevsim: peer.sh # exit=1
This patch also solves timeout on TCP Fast Open (TFO) test in
NetworkManager-based systems because it also depends on netdevsim's
carrier consistency.
Fixes: 1a8fed52f7be ("netdevsim: set the carrier when the device goes up")
Signed-off-by: Yohei Kojima <yk@y-koj.net>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/602c9e1ba5bb2ee1997bb38b1d866c9c3b807ae9.1767624906.git.yk@y-koj.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 086efe0a1ecc36cffe46640ce12649a4cd3ff171 ]
The HW only supports a maximum Rx buffer size of 16K-128. On systems
using large pages, the libeth logic can configure the buffer size to be
larger than this. The upper bound is PAGE_SIZE while the lower bound is
MTU rounded up to the nearest power of 2. For example, ARM systems with
a 64K page size and an mtu of 9000 will set the Rx buffer size to 16K,
which will cause the config Rx queues message to fail.
Initialize the bufq/fill queue buf_len field to the maximum supported
size. This will trigger the libeth logic to cap the maximum Rx buffer
size by reducing the upper bound.
Fixes: 74d1412ac8f37 ("idpf: use libeth Rx buffer management for payload buffer")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: David Decotigny <ddecotig@google.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f6242b354605faff263ca45882b148200915a3f6 ]
Free vport->rx_ptype_lkup in idpf_vport_rel() to avoid leaking memory
during a reset. Reported by kmemleak:
unreferenced object 0xff450acac838a000 (size 4096):
comm "kworker/u258:5", pid 7732, jiffies 4296830044
hex dump (first 32 bytes):
00 00 00 00 00 10 00 00 00 10 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 ................
backtrace (crc 3da81902):
__kmalloc_cache_noprof+0x469/0x7a0
idpf_send_get_rx_ptype_msg+0x90/0x570 [idpf]
idpf_init_task+0x1ec/0x8d0 [idpf]
process_one_work+0x226/0x6d0
worker_thread+0x19e/0x340
kthread+0x10f/0x250
ret_from_fork+0x251/0x2b0
ret_from_fork_asm+0x1a/0x30
Fixes: 0fe45467a104 ("idpf: add create vport and netdev configuration")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 083029bd8b445595222a3cd14076b880781c1765 ]
During a successful reset the driver would re-allocate vport resources
while keeping the netdevs intact. However, in case of an error in the
init task, the netdev of the failing vport will be unregistered,
effectively removing the network interface:
[ 121.211076] idpf 0000:83:00.0: enabling device (0100 -> 0102)
[ 121.221976] idpf 0000:83:00.0: Device HW Reset initiated
[ 124.161229] idpf 0000:83:00.0 ens801f0: renamed from eth0
[ 124.163364] idpf 0000:83:00.0 ens801f0d1: renamed from eth1
[ 125.934656] idpf 0000:83:00.0 ens801f0d2: renamed from eth2
[ 128.218429] idpf 0000:83:00.0 ens801f0d3: renamed from eth3
ip -br a
ens801f0 UP
ens801f0d1 UP
ens801f0d2 UP
ens801f0d3 UP
echo 1 > /sys/class/net/ens801f0/device/reset
[ 145.885537] idpf 0000:83:00.0: resetting
[ 145.990280] idpf 0000:83:00.0: reset done
[ 146.284766] idpf 0000:83:00.0: HW reset detected
[ 146.296610] idpf 0000:83:00.0: Device HW Reset initiated
[ 211.556719] idpf 0000:83:00.0: Transaction timed-out (op:526 cookie:7700 vc_op:526 salt:77 timeout:60000ms)
[ 272.996705] idpf 0000:83:00.0: Transaction timed-out (op:502 cookie:7800 vc_op:502 salt:78 timeout:60000ms)
ip -br a
ens801f0d1 DOWN
ens801f0d2 DOWN
ens801f0d3 DOWN
Re-shuffle the logic in the error path of the init task to make sure the
netdevs remain intact. This will allow the driver to attempt recovery via
subsequent resets, provided the FW is still functional.
The main change is to make sure that idpf_decfg_netdev() is not called
should the init task fail during a reset. The error handling is
consolidated under unwind_vports, as the removed labels had the same
cleanup logic split depending on the point of failure.
Fixes: ce1b75d0635c ("idpf: add ptypes and MAC filter support")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ffeafa65b2b26df2f5b5a6118d3174f17bd12ec5 ]
Fix the max number of bits passed to find_first_zero_bit() in
bnxt_alloc_agg_idx(). We were incorrectly passing the number of
long words. find_first_zero_bit() may fail to find a zero bit and
cause a wrong ID to be used. If the wrong ID is already in use, this
can cause data corruption. Sometimes an error like this can also be
seen:
bnxt_en 0000:83:00.0 enp131s0np0: TPA end agg_buf 2 != expected agg_bufs 1
Fix it by passing the correct number of bits MAX_TPA_P5. Use
DECLARE_BITMAP() to more cleanly define the bitmap. Add a sanity
check to warn if a bit cannot be found and reset the ring [MChan].
Fixes: ec4d8e7cf024 ("bnxt_en: Add TPA ID mapping logic for 57500 chips.")
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Srijit Bose <srijit.bose@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251231083625.3911652-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 92e6e0a87f6860a4710f9494f8c704d498ae60f8 ]
Commit 1f52d7b62285 ("net: wwan: iosm: Enable M.2 7360 WWAN card support")
allocated memory for pp_qlt in ipc_mux_init() but did not free it in
ipc_mux_deinit(). This results in a memory leak when the driver is
unloaded.
Free the allocated memory in ipc_mux_deinit() to fix the leak.
Fixes: 1f52d7b62285 ("net: wwan: iosm: Enable M.2 7360 WWAN card support")
Co-developed-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20251230071853.1062223-1-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 144297e2a24e3e54aee1180ec21120ea38822b97 ]
Dumping module EEPROM on newer modules is supported through the netlink
interface only.
Querying with old userspace ethtool (or other tools, such as 'lshw')
which still uses the ioctl interface results in an error message that
could flood dmesg (in addition to the expected error return value).
The original message was added under the assumption that the driver
should be able to handle all module types, but now that such flows are
easily triggered from userspace, it doesn't serve its purpose.
Change the log level of the print in mlx5_query_module_eeprom() to
debug.
Fixes: bb64143eee8c ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20251225132717.358820-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 34f3ff52cb9fa7dbf04f5c734fcc4cb6ed5d1a95 ]
Commit 15faa1f67ab4 ("lan966x: Fix crash when adding interface under a lag")
fixed a similar issue in the lan966x driver caused by a NULL pointer dereference.
The ocelot_set_aggr_pgids() function in the ocelot driver has similar logic
and is susceptible to the same crash.
This issue specifically affects the ocelot_vsc7514.c frontend, which leaves
unused ports as NULL pointers. The felix_vsc9959.c frontend is unaffected as
it uses the DSA framework which registers all ports.
Fix this by checking if the port pointer is valid before accessing it.
Fixes: 528d3f190c98 ("net: mscc: ocelot: drop the use of the "lags" array")
Signed-off-by: Jerry Wu <w.7erry@foxmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/tencent_75EF812B305E26B0869C673DD1160866C90A@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a428e0da1248c353557970848994f35fd3f005e2 ]
devlink_alloc() may return NULL on allocation failure, but
prestera_devlink_alloc() unconditionally calls devlink_priv() on
the returned pointer.
This leads to a NULL pointer dereference if devlink allocation fails.
Add a check for a NULL devlink pointer and return NULL early to avoid
the crash.
Fixes: 34dd1710f5a3 ("net: marvell: prestera: Add basic devlink support")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Acked-by: Elad Nachman <enachman@marvell.com>
Link: https://patch.msgid.link/20251230052124.897012-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a4e305ed60f7c41bbf9aabc16dd75267194e0de3 upstream.
pdev can be null and free_ring: can be called in 1297 with a null
pdev.
Fixes: 55c82617c3e8 ("3c59x: convert to generic DMA API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Link: https://patch.msgid.link/20260106094731.25819-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1e5a541420b8c6d87d88eb50b6b978cdeafee1c9 ]
When nvmem_cell_read() fails in mt798x_phy_calibration(), the function
returns without calling nvmem_cell_put(), leaking the cell reference.
Move nvmem_cell_put() right after nvmem_cell_read() to ensure the cell
reference is always released regardless of the read result.
Found via static analysis and code review.
Fixes: 98c485eaf509 ("net: phy: add driver for MediaTek SoC built-in GE PHYs")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251211081313.2368460-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d970eda003441f66551a91fda16478ac0711617 upstream.
Currently, interrupts are automatically enabled immediately upon
request. This allows interrupt to fire before the associated NAPI
context is fully initialized and cause failures like below:
[ 0.946369] Call Trace:
[ 0.946369] <IRQ>
[ 0.946369] __napi_poll+0x2a/0x1e0
[ 0.946369] net_rx_action+0x2f9/0x3f0
[ 0.946369] handle_softirqs+0xd6/0x2c0
[ 0.946369] ? handle_edge_irq+0xc1/0x1b0
[ 0.946369] __irq_exit_rcu+0xc3/0xe0
[ 0.946369] common_interrupt+0x81/0xa0
[ 0.946369] </IRQ>
[ 0.946369] <TASK>
[ 0.946369] asm_common_interrupt+0x22/0x40
[ 0.946369] RIP: 0010:pv_native_safe_halt+0xb/0x10
Use the `IRQF_NO_AUTOEN` flag when requesting interrupts to prevent auto
enablement and explicitly enable the interrupt in NAPI initialization
path (and disable it during NAPI teardown).
This ensures that interrupt lifecycle is strictly coupled with
readiness of NAPI context.
Cc: stable@vger.kernel.org
Fixes: 1dfc2e46117e ("gve: Refactor napi add and remove functions")
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Reviewed-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20251219102945.2193617-1-hramamurthy@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6c4e68480238274f84aa50d54da0d9e262df6284 ]
Changes from original commit:
- Adjusted idpf_tx_queue assert size to align with 6.12 struct definition
With the new Tx buffer management scheme, there is no need for all of
the stashing mechanisms, the hash table, the reserve buffer stack, etc.
Remove all of that.
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0c3f135e840d4a2ba4253e15d530ec61bc30718e ]
The Tx refillq logic will cause packets to be silently dropped if there
are not enough buffer resources available to send a packet in flow
scheduling mode. Instead, determine how many buffers are needed along
with number of descriptors. Make sure there are enough of both resources
to send the packet, and stop the queue if not.
Fixes: 7292af042bcf ("idpf: fix a race in txq wakeup")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5f417d551324d2894168b362f2429d120ab06243 ]
Replace the TxQ buffer ring with one large pool/array of buffers (only
for flow scheduling). This eliminates the tag generation and makes it
impossible for a tag to be associated with more than one packet.
The completion tag passed to HW through the descriptor is the index into
the array. That same completion tag is posted back to the driver in the
completion descriptor, and used to index into the array to quickly
retrieve the buffer during cleaning. In this way, the tags are treated
as a fix sized resource. If all tags are in use, no more packets can be
sent on that particular queue (until some are freed up). The tag pool
size is 64K since the completion tag width is 16 bits.
For each packet, the driver pulls a free tag from the refillq to get the
next free buffer index. When cleaning is complete, the tag is posted
back to the refillq. A multi-frag packet spans multiple buffers in the
driver, therefore it uses multiple buffer indexes/tags from the pool.
Each frag pulls from the refillq to get the next free buffer index.
These are tracked in a next_buf field that replaces the completion tag
field in the buffer struct. This chains the buffers together so that the
packet can be cleaned from the starting completion tag taken from the
completion descriptor, then from the next_buf field for each subsequent
buffer.
In case of a dma_mapping_error occurs or the refillq runs out of free
buf_ids, the packet will execute the rollback error path. This unmaps
any buffers previously mapped for the packet. Since several free
buf_ids could have already been pulled from the refillq, we need to
restore its original state as well. Otherwise, the buf_ids/tags
will be leaked and not used again until the queue is reallocated.
Descriptor completions only advance the descriptor ring index to "clean"
the descriptors. The packet completions only clean the buffers
associated with the given packet completion tag and do not update the
descriptor ring index.
When operating in queue based scheduling mode, the array still acts as a
ring and will only have TxQ descriptor count entries. The tx_bufs are
still associated 1:1 with the descriptor ring entries and we can use the
conventional indexing mechanisms.
Fixes: c2d548cad150 ("idpf: add TX splitq napi poll support")
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b61dfa9bc4430ad82b96d3a7c1c485350f91b467 ]
Move (and rename) the existing rollback logic to singleq.c since that
will be the only consumer. Create a simplified splitq specific rollback
function to loop through and unmap tx_bufs based on the completion tag.
This is critical before replacing the Tx buffer ring with the buffer
pool since the previous rollback indexing will not work to unmap the
chained buffers from the pool.
Cache the next_to_use index before any portion of the packet is put on
the descriptor ring. In case of an error, the rollback will bump tail to
the correct next_to_use value. Because the splitq path now supports
different types of context descriptors (and potentially multiple in the
future), this will take care of rolling back any and all context
descriptors encoded on the ring for the erroneous packet. The previous
rollback logic was broken for PTP packets since it would not account for
the PTP context descriptor.
Fixes: 1a49cf814fe1 ("idpf: add Tx timestamp flows")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f2d18e16479cac7a708d77cbfb4220a9114a71fc ]
Track the gap between next_to_use and the last RE index. Set RE again
if the gap is large enough to ensure RE bit is set frequently. This is
critical before removing the stashing mechanisms because the
opportunistic descriptor ring cleaning from the out-of-order completions
will go away. Previously the descriptors would be "cleaned" by both the
descriptor (RE) completion and the out-of-order completions. Without the
latter, we must ensure the RE bit is set more frequently. Otherwise,
it's theoretically possible for the descriptor ring next_to_clean to
never advance. The previous implementation was dependent on the start
of a packet falling on a 64th index in the descriptor ring, which is not
guaranteed with large packets.
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cb83b559bea39f207ee214ee2972657e8576ed18 ]
Changes from original commit:
- Adjusted idpf_tx_queue assert size to align with 6.12 struct definition
In certain production environments, it is possible for completion tags
to collide, meaning N packets with the same completion tag are in flight
at the same time. In this environment, any given Tx queue is effectively
used to send both slower traffic and higher throughput traffic
simultaneously. This is the result of a customer's specific
configuration in the device pipeline, the details of which Intel cannot
provide. This configuration results in a small number of out-of-order
completions, i.e., a small number of packets in flight. The existing
guardrails in the driver only protect against a large number of packets
in flight. The slower flow completions are delayed which causes the
out-of-order completions. The fast flow will continue sending traffic
and generating tags. Because tags are generated on the fly, the fast
flow eventually uses the same tag for a packet that is still in flight
from the slower flow. The driver has no idea which packet it should
clean when it processes the completion with that tag, but it will look
for the packet on the buffer ring before the hash table. If the slower
flow packet completion is processed first, it will end up cleaning the
fast flow packet on the ring prematurely. This leaves the descriptor
ring in a bad state resulting in a crash or Tx timeout.
In summary, generating a tag when a packet is sent can lead to the same
tag being associated with multiple packets. This can lead to resource
leaks, crashes, and/or Tx timeouts.
Before we can replace the tag generation, we need a new mechanism for
the send path to know what tag to use next. The driver will allocate and
initialize a refillq for each TxQ with all of the possible free tag
values. During send, the driver grabs the next free tag from the refillq
from next_to_clean. While cleaning the packet, the clean routine posts
the tag back to the refillq's next_to_use to indicate that it is now
free to use.
This mechanism works exactly the same way as the existing Rx refill
queues, which post the cleaned buffer IDs back to the buffer queue to be
reposted to HW. Since we're using the refillqs for both Rx and Tx now,
genericize some of the existing refillq support.
Note: the refillqs will not be used yet. This is only demonstrating how
they will be used to pass free tags back to the send path.
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0c1683c681681c14f4389e3bfa8de10baf242ba8 ]
There is a race condition between exiting wb_on_itr and completion write
backs. For example, we are in wb_on_itr mode and a Tx completion is
generated by HW, ready to be written back, as we are re-enabling
interrupts:
HW SW
| |
| | idpf_tx_splitq_clean_all
| | napi_complete_done
| |
| tx_completion_wb | idpf_vport_intr_update_itr_ena_irq
That tx_completion_wb happens before the vector is fully re-enabled.
Continuing with this example, it is a UDP stream and the
tx_completion_wb is the last one in the flow (there are no rx packets).
Because the HW generated the completion before the interrupt is fully
enabled, the HW will not fire the interrupt once the timer expires and
the write back will not happen. NAPI poll won't be called. We have
indicated we're back in interrupt mode but nothing else will trigger the
interrupt. Therefore, the completion goes unprocessed, triggering a Tx
timeout.
To mitigate this, fire a SW triggered interrupt upon exiting wb_on_itr.
This interrupt will catch the rogue completion and avoid the timeout.
Add logic to set the appropriate bits in the vector's dyn_ctl register.
Fixes: 9c4a27da0ecc ("idpf: enable WB_ON_ITR")
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 93433c1d919775f8ac0f7893692f42e6731a5373 ]
SW triggered interrupts are guaranteed to fire after their timer
expires, unlike Tx and Rx interrupts which will only fire after the
timer expires _and_ a descriptor write back is available to be processed
by the driver.
Add the necessary fields, defines, and initializations to enable a SW
triggered interrupt in the vector's dyn_ctl register.
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8f6571ad470feb242dcef36e53f7cf1bba03780f ]
When the system suspend or resume, the WiFi driver sends
an hif_ctrl command to the firmware and waits for an event.
Due to changes in the event format reported by the chip, the
current mt7925's driver does not account for these changes,
resulting in command timeout. Add flow to handle hif_ctrl
event to avoid command timeout. We also exented API
mt76_connac_mcu_set_hif_suspend for connac3 this time.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Link: https://patch.msgid.link/3a0844ff5162142c4a9f3cf7104f75076ddd3b87.1735910562.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a0f721b8d986b62b4de316444f2b2e356d17e3b5 ]
When enter suspend/resume while in a connected state, the upper layer
will trigger disconnection before entering suspend, and at the same time,
it will trigger regd_notifier() and update CLC, causing the CLC event to
not be received due to suspend, resulting in a command timeout.
Therefore, the update of CLC is postponed until resume, to ensure data
consistency and avoid the occurrence of command timeout.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Link: https://patch.msgid.link/bab00a2805d0533fd8beaa059222659858a9dcb5.1735910455.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1b97fc8443aea01922560de9f24a6383e6eb6ae8 ]
Before entering suspend, we need to ensure that all MCU command are
completed. In some cases, such as with regd_notifier, there is a
chance that CLC commands, will be executed before suspend.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Link: https://patch.msgid.link/3af7b4e5bf7437832b016e32743657d1d55b1f9d.1735910288.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 327cd4b68b4398b6c24f10eb2b2533ffbfc10185 ]
Syzbot reported the following warning:
BUG: using smp_processor_id() in preemptible [00000000] code: dhcpcd/2879
caller is usbnet_skb_return+0x74/0x490 drivers/net/usb/usbnet.c:331
CPU: 1 UID: 0 PID: 2879 Comm: dhcpcd Not tainted 6.15.0-rc4-syzkaller-00098-g615dca38c2ea #0 PREEMPT(voluntary)
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x16c/0x1f0 lib/dump_stack.c:120
check_preemption_disabled+0xd0/0xe0 lib/smp_processor_id.c:49
usbnet_skb_return+0x74/0x490 drivers/net/usb/usbnet.c:331
usbnet_resume_rx+0x4b/0x170 drivers/net/usb/usbnet.c:708
usbnet_change_mtu+0x1be/0x220 drivers/net/usb/usbnet.c:417
__dev_set_mtu net/core/dev.c:9443 [inline]
netif_set_mtu_ext+0x369/0x5c0 net/core/dev.c:9496
netif_set_mtu+0xb0/0x160 net/core/dev.c:9520
dev_set_mtu+0xae/0x170 net/core/dev_api.c:247
dev_ifsioc+0xa31/0x18d0 net/core/dev_ioctl.c:572
dev_ioctl+0x223/0x10e0 net/core/dev_ioctl.c:821
sock_do_ioctl+0x19d/0x280 net/socket.c:1204
sock_ioctl+0x42f/0x6a0 net/socket.c:1311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:906 [inline]
__se_sys_ioctl fs/ioctl.c:892 [inline]
__x64_sys_ioctl+0x190/0x200 fs/ioctl.c:892
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xcd/0x260 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
For historical and portability reasons, the netif_rx() is usually
run in the softirq or interrupt context, this commit therefore add
local_bh_disable/enable() protection in the usbnet_resume_rx().
Fixes: 43daa96b166c ("usbnet: Stop RX Q on MTU change")
Link: https://syzkaller.appspot.com/bug?id=81f55dfa587ee544baaaa5a359a060512228c1e1
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Zqiang <qiang.zhang@linux.dev>
Link: https://patch.msgid.link/20251011070518.7095-1-qiang.zhang@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
[Harshit: Resolved conflicts due to missing commit: 2c04d279e857 ("net:
usb: Convert tasklet API to new bottom half workqueue mechanism") in
6.12.y]
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
macb_open()
commit 99537d5c476cada9cf75aef9fa75579a31faadb9 upstream.
In the non-RT kernel, local_bh_disable() merely disables preemption,
whereas it maps to an actual spin lock in the RT kernel. Consequently,
when attempting to refill RX buffers via netdev_alloc_skb() in
macb_mac_link_up(), a deadlock scenario arises as follows:
WARNING: possible circular locking dependency detected
6.18.0-08691-g2061f18ad76e #39 Not tainted
------------------------------------------------------
kworker/0:0/8 is trying to acquire lock:
ffff00080369bbe0 (&bp->lock){+.+.}-{3:3}, at: macb_start_xmit+0x808/0xb7c
but task is already holding lock:
ffff000803698e58 (&queue->tx_ptr_lock){+...}-{3:3}, at: macb_start_xmit
+0x148/0xb7c
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&queue->tx_ptr_lock){+...}-{3:3}:
rt_spin_lock+0x50/0x1f0
macb_start_xmit+0x148/0xb7c
dev_hard_start_xmit+0x94/0x284
sch_direct_xmit+0x8c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
-> #2 (_xmit_ETHER#2){+...}-{3:3}:
rt_spin_lock+0x50/0x1f0
sch_direct_xmit+0x11c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
-> #1 ((softirq_ctrl.lock)){+.+.}-{3:3}:
lock_release+0x250/0x348
__local_bh_enable_ip+0x7c/0x240
__netdev_alloc_skb+0x1b4/0x1d8
gem_rx_refill+0xdc/0x240
gem_init_rings+0xb4/0x108
macb_mac_link_up+0x9c/0x2b4
phylink_resolve+0x170/0x614
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
-> #0 (&bp->lock){+.+.}-{3:3}:
__lock_acquire+0x15a8/0x2084
lock_acquire+0x1cc/0x350
rt_spin_lock+0x50/0x1f0
macb_start_xmit+0x808/0xb7c
dev_hard_start_xmit+0x94/0x284
sch_direct_xmit+0x8c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
other info that might help us debug this:
Chain exists of:
&bp->lock --> _xmit_ETHER#2 --> &queue->tx_ptr_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&queue->tx_ptr_lock);
lock(_xmit_ETHER#2);
lock(&queue->tx_ptr_lock);
lock(&bp->lock);
*** DEADLOCK ***
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0xa0/0xf0
dump_stack+0x18/0x24
print_circular_bug+0x28c/0x370
check_noncircular+0x198/0x1ac
__lock_acquire+0x15a8/0x2084
lock_acquire+0x1cc/0x350
rt_spin_lock+0x50/0x1f0
macb_start_xmit+0x808/0xb7c
dev_hard_start_xmit+0x94/0x284
sch_direct_xmit+0x8c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
Notably, invoking the mog_init_rings() callback upon link establishment
is unnecessary. Instead, we can exclusively call mog_init_rings() within
the ndo_open() callback. This adjustment resolves the deadlock issue.
Furthermore, since MACB_CAPS_MACB_IS_EMAC cases do not use mog_init_rings()
when opening the network interface via at91ether_open(), moving
mog_init_rings() to macb_open() also eliminates the MACB_CAPS_MACB_IS_EMAC
check.
Fixes: 633e98a711ac ("net: macb: use resolved link config in mac_link_up()")
Cc: stable@vger.kernel.org
Suggested-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://patch.msgid.link/20251222015624.1994551-1-xiaolei.wang@windriver.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa0b198be1c6775bc7804731a43be5d899d19e7a upstream.
This fixes the device failing to initialize with "error reading MAC
address" for me, probably because the incorrect write of NCR_RST to
SR_NCR is not actually resetting the device.
Fixes: c9b37458e95629b1d1171457afdcc1bf1eb7881d ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Cc: stable@vger.kernel.org
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20251221082400.50688-1-enelsonmoore@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15ef641a0c6728d25a400df73922e80ab2cf029c upstream.
In error paths, add fjes_hw_iounmap() to release the
resource acquired by fjes_hw_iomap(). Add a goto label
to do so.
Fixes: 8cdc3f6c5d22 ("fjes: Hardware initialization routine")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251211073756.101824-1-lihaoxiang@isrc.iscas.ac.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c72a5182ed92904d01057f208c390a303f00a0f upstream.
In e1000_tbi_should_accept() we read the last byte of the frame via
'data[length - 1]' to evaluate the TBI workaround. If the descriptor-
reported length is zero or larger than the actual RX buffer size, this
read goes out of bounds and can hit unrelated slab objects. The issue
is observed from the NAPI receive path (e1000_clean_rx_irq):
==================================================================
BUG: KASAN: slab-out-of-bounds in e1000_tbi_should_accept+0x610/0x790
Read of size 1 at addr ffff888014114e54 by task sshd/363
CPU: 0 PID: 363 Comm: sshd Not tainted 5.18.0-rc1 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x5a/0x74
print_address_description+0x7b/0x440
print_report+0x101/0x200
kasan_report+0xc1/0xf0
e1000_tbi_should_accept+0x610/0x790
e1000_clean_rx_irq+0xa8c/0x1110
e1000_clean+0xde2/0x3c10
__napi_poll+0x98/0x380
net_rx_action+0x491/0xa20
__do_softirq+0x2c9/0x61d
do_softirq+0xd1/0x120
</IRQ>
<TASK>
__local_bh_enable_ip+0xfe/0x130
ip_finish_output2+0x7d5/0xb00
__ip_queue_xmit+0xe24/0x1ab0
__tcp_transmit_skb+0x1bcb/0x3340
tcp_write_xmit+0x175d/0x6bd0
__tcp_push_pending_frames+0x7b/0x280
tcp_sendmsg_locked+0x2e4f/0x32d0
tcp_sendmsg+0x24/0x40
sock_write_iter+0x322/0x430
vfs_write+0x56c/0xa60
ksys_write+0xd1/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f511b476b10
Code: 73 01 c3 48 8b 0d 88 d3 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d f9 2b 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 8e 9b 01 00 48 89 04 24
RSP: 002b:00007ffc9211d4e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000004024 RCX: 00007f511b476b10
RDX: 0000000000004024 RSI: 0000559a9385962c RDI: 0000000000000003
RBP: 0000559a9383a400 R08: fffffffffffffff0 R09: 0000000000004f00
R10: 0000000000000070 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffc9211d57f R14: 0000559a9347bde7 R15: 0000000000000003
</TASK>
Allocated by task 1:
__kasan_krealloc+0x131/0x1c0
krealloc+0x90/0xc0
add_sysfs_param+0xcb/0x8a0
kernel_add_sysfs_param+0x81/0xd4
param_sysfs_builtin+0x138/0x1a6
param_sysfs_init+0x57/0x5b
do_one_initcall+0x104/0x250
do_initcall_level+0x102/0x132
do_initcalls+0x46/0x74
kernel_init_freeable+0x28f/0x393
kernel_init+0x14/0x1a0
ret_from_fork+0x22/0x30
The buggy address belongs to the object at ffff888014114000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1620 bytes to the right of
2048-byte region [ffff888014114000, ffff888014114800]
The buggy address belongs to the physical page:
page:ffffea0000504400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x14110
head:ffffea0000504400 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x100000000010200(slab|head|node=0|zone=1)
raw: 0100000000010200 0000000000000000 dead000000000001 ffff888013442000
raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
==================================================================
This happens because the TBI check unconditionally dereferences the last
byte without validating the reported length first:
u8 last_byte = *(data + length - 1);
Fix by rejecting the frame early if the length is zero, or if it exceeds
adapter->rx_buffer_len. This preserves the TBI workaround semantics for
valid frames and prevents touching memory beyond the RX buffer.
Fixes: 2037110c96d5 ("e1000: move tbi workaround code into helper function")
Cc: stable@vger.kernel.org
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a48e232210009be50591fdea8ba7c07b0f566a13 ]
There is a crash issue when running zero copy XDP_TX action, the crash
log is shown below.
[ 216.122464] Unable to handle kernel paging request at virtual address fffeffff80000000
[ 216.187524] Internal error: Oops: 0000000096000144 [#1] SMP
[ 216.301694] Call trace:
[ 216.304130] dcache_clean_poc+0x20/0x38 (P)
[ 216.308308] __dma_sync_single_for_device+0x1bc/0x1e0
[ 216.313351] stmmac_xdp_xmit_xdpf+0x354/0x400
[ 216.317701] __stmmac_xdp_run_prog+0x164/0x368
[ 216.322139] stmmac_napi_poll_rxtx+0xba8/0xf00
[ 216.326576] __napi_poll+0x40/0x218
[ 216.408054] Kernel panic - not syncing: Oops: Fatal exception in interrupt
For XDP_TX action, the xdp_buff is converted to xdp_frame by
xdp_convert_buff_to_frame(). The memory type of the resulting xdp_frame
depends on the memory type of the xdp_buff. For page pool based xdp_buff
it produces xdp_frame with memory type MEM_TYPE_PAGE_POOL. For zero copy
XSK pool based xdp_buff it produces xdp_frame with memory type
MEM_TYPE_PAGE_ORDER0. However, stmmac_xdp_xmit_back() does not check the
memory type and always uses the page pool type, this leads to invalid
mappings and causes the crash. Therefore, check the xdp_buff memory type
in stmmac_xdp_xmit_back() to fix this issue.
Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20251204071332.1907111-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 85f4b0c650d9f9db10bda8d3acfa1af83bf78cf7 ]
This patch ensures that the RX ring size (rx_pending) is not
set below the permitted length. This avoids UBSAN
shift-out-of-bounds errors when users passes small or zero
ring sizes via ethtool -G.
Fixes: d45d8979840d ("octeontx2-pf: Add basic ethtool support")
Signed-off-by: Anshumali Gaur <agaur@marvell.com>
Link: https://patch.msgid.link/20251219062226.524844-1-agaur@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a1e077a3f76eea0dc671ed6792e7d543946227e8 ]
The ASIX driver reads the PHY address from the USB device via
asix_read_phy_addr(). A malicious or faulty device can return an
invalid address (>= PHY_MAX_ADDR), which causes a warning in
mdiobus_get_phy():
addr 207 out of range
WARNING: drivers/net/phy/mdio_bus.c:76
Validate the PHY address in asix_read_phy_addr() and remove the
now-redundant check in ax88172a.c.
Reported-by: syzbot+3d43c9066a5b54902232@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=3d43c9066a5b54902232
Tested-by: syzbot+3d43c9066a5b54902232@syzkaller.appspotmail.com
Fixes: 7e88b11a862a ("net: usb: asix: refactor asix_read_phy_addr() and handle errors on return")
Link: https://lore.kernel.org/all/20251217085057.270704-1-kartikey406@gmail.com/T/ [v1]
Signed-off-by: Deepanshu Kartikey <kartikey406@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251218011156.276824-1-kartikey406@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d42bce414d1c5c0b536758466a1f63ac358e613c ]
port_fdb_dump() is supposed to only add fdb entries, but we iterate over
the full ARL table, which also includes multicast entries.
So check if the entry is a multicast entry before passing it on to the
callback().
Additionally, the port of those entries is a bitmask, not a port number,
so any included entries would have even be for the wrong port.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251217205756.172123-1-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6402078bd9d1ed46e79465e1faaa42e3458f8a33 ]
When smc91x.c is built with PREEMPT_RT, the following splat occurs
in FVP_RevC:
[ 13.055000] smc91x LNRO0003:00 eth0: link up, 10Mbps, half-duplex, lpa 0x0000
[ 13.062137] BUG: workqueue leaked atomic, lock or RCU: kworker/2:1[106]
[ 13.062137] preempt=0x00000000 lock=0->0 RCU=0->1 workfn=mld_ifc_work
[ 13.062266] C
** replaying previous printk message **
[ 13.062266] CPU: 2 UID: 0 PID: 106 Comm: kworker/2:1 Not tainted 6.18.0-dirty #179 PREEMPT_{RT,(full)}
[ 13.062353] Hardware name: , BIOS
[ 13.062382] Workqueue: mld mld_ifc_work
[ 13.062469] Call trace:
[ 13.062494] show_stack+0x24/0x40 (C)
[ 13.062602] __dump_stack+0x28/0x48
[ 13.062710] dump_stack_lvl+0x7c/0xb0
[ 13.062818] dump_stack+0x18/0x34
[ 13.062926] process_scheduled_works+0x294/0x450
[ 13.063043] worker_thread+0x260/0x3d8
[ 13.063124] kthread+0x1c4/0x228
[ 13.063235] ret_from_fork+0x10/0x20
This happens because smc_special_trylock() disables IRQs even on PREEMPT_RT,
but smc_special_unlock() does not restore IRQs on PREEMPT_RT.
The reason is that smc_special_unlock() calls spin_unlock_irqrestore(),
and rcu_read_unlock_bh() in __dev_queue_xmit() cannot invoke
rcu_read_unlock() through __local_bh_enable_ip() when current->softirq_disable_cnt becomes zero.
To address this issue, replace smc_special_trylock() with spin_trylock_irqsave().
Fixes: 342a93247e08 ("locking/spinlock: Provide RT variant header: <linux/spinlock_rt.h>")
Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251217085115.1730036-1-yeoreum.yun@arm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 12cab1191d9890097171156d06bfa8d31f1e39c8 ]
In async_set_registers(), when usb_submit_urb() fails, the allocated
async_req structure and URB are not freed, causing a memory leak.
The completion callback async_set_reg_cb() is responsible for freeing
these allocations, but it is only called after the URB is successfully
submitted and completes (successfully or with error). If submission
fails, the callback never runs and the memory is leaked.
Fix this by freeing both the URB and the request structure in the error
path when usb_submit_urb() fails.
Reported-by: syzbot+8dd915c7cb0490fc8c52@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=8dd915c7cb0490fc8c52
Fixes: 4d12997a9bb3 ("drivers: net: usb: rtl8150: concurrent URB bugfix")
Signed-off-by: Deepakkumar Karn <dkarn@redhat.com>
Link: https://patch.msgid.link/20251216151304.59865-2-dkarn@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit df60c332caf95d70f967aeace826e7e2f0847361 ]
During the stress tests, early RX adaptation handshakes can fail, such
as missing the RX_ADAPT ACK or not receiving a coefficient update before
block lock is established. Continuing to retry RX adaptation in this
state is often ineffective if the current mode selection is not viable.
Resetting the RX adaptation retry counter when an RX_ADAPT request fails
to receive ACK or a coefficient update prior to block lock, and clearing
mode_set so the next bring-up performs a fresh mode selection rather
than looping on a likely invalid configuration.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://patch.msgid.link/20251215151728.311713-1-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 932ac51d9953eaf77a1252f79b656d4ca86163c6 ]
There has been a syzkaller bug reported recently with the following
trace:
list_del corruption, ffff888058bea080->prev is LIST_POISON2 (dead000000000122)
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:59!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 3 UID: 0 PID: 21246 Comm: syz.0.2928 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
RIP: 0010:__list_del_entry_valid_or_report+0x13e/0x200 lib/list_debug.c:59
Code: 48 c7 c7 e0 71 f0 8b e8 30 08 ef fc 90 0f 0b 48 89 ef e8 a5 02 55 fd 48 89 ea 48 89 de 48 c7 c7 40 72 f0 8b e8 13 08 ef fc 90 <0f> 0b 48 89 ef e8 88 02 55 fd 48 89 ea 48 b8 00 00 00 00 00 fc ff
RSP: 0018:ffffc9000d49f370 EFLAGS: 00010286
RAX: 000000000000004e RBX: ffff888058bea080 RCX: ffffc9002817d000
RDX: 0000000000000000 RSI: ffffffff819becc6 RDI: 0000000000000005
RBP: dead000000000122 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000080000000 R11: 0000000000000001 R12: ffff888039e9c230
R13: ffff888058bea088 R14: ffff888058bea080 R15: ffff888055461480
FS: 00007fbbcfe6f6c0(0000) GS:ffff8880d6d0a000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000110c3afcb0 CR3: 00000000382c7000 CR4: 0000000000352ef0
Call Trace:
<TASK>
__list_del_entry_valid include/linux/list.h:132 [inline]
__list_del_entry include/linux/list.h:223 [inline]
list_del_rcu include/linux/rculist.h:178 [inline]
__team_queue_override_port_del drivers/net/team/team_core.c:826 [inline]
__team_queue_override_port_del drivers/net/team/team_core.c:821 [inline]
team_queue_override_port_prio_changed drivers/net/team/team_core.c:883 [inline]
team_priority_option_set+0x171/0x2f0 drivers/net/team/team_core.c:1534
team_option_set drivers/net/team/team_core.c:376 [inline]
team_nl_options_set_doit+0x8ae/0xe60 drivers/net/team/team_core.c:2653
genl_family_rcv_msg_doit+0x209/0x2f0 net/netlink/genetlink.c:1115
genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline]
genl_rcv_msg+0x55c/0x800 net/netlink/genetlink.c:1210
netlink_rcv_skb+0x158/0x420 net/netlink/af_netlink.c:2552
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219
netlink_unicast_kernel net/netlink/af_netlink.c:1320 [inline]
netlink_unicast+0x5aa/0x870 net/netlink/af_netlink.c:1346
netlink_sendmsg+0x8c8/0xdd0 net/netlink/af_netlink.c:1896
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
____sys_sendmsg+0xa98/0xc70 net/socket.c:2630
___sys_sendmsg+0x134/0x1d0 net/socket.c:2684
__sys_sendmsg+0x16d/0x220 net/socket.c:2716
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xcd/0xfa0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The problem is in this flow:
1) Port is enabled, queue_id != 0, in qom_list
2) Port gets disabled
-> team_port_disable()
-> team_queue_override_port_del()
-> del (removed from list)
3) Port is disabled, queue_id != 0, not in any list
4) Priority changes
-> team_queue_override_port_prio_changed()
-> checks: port disabled && queue_id != 0
-> calls del - hits the BUG as it is removed already
To fix this, change the check in team_queue_override_port_prio_changed()
so it returns early if port is not enabled.
Reported-by: syzbot+422806e5f4cce722a71f@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=422806e5f4cce722a71f
Fixes: 6c31ff366c11 ("team: remove synchronize_rcu() called during queue override change")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251212102953.167287-1-jiri@resnulli.us
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d1a1a4bade4b20c0858d0b2f81d2611de055f675 ]
The Aspeed MDIO controller may return incorrect data when a read operation
follows immediately after a write. Due to a controller bug, the subsequent
read can latch stale data, causing the polling logic to terminate earlier
than expected.
To work around this hardware issue, insert a dummy read after each write
operation. This ensures that the next actual read returns the correct
data and prevents premature polling exit.
This workaround has been verified to stabilize MDIO transactions on
affected Aspeed platforms.
Fixes: f160e99462c6 ("net: phy: Add mdio-aspeed")
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251211-aspeed_mdio_add_dummy_read-v3-1-382868869004@aspeedtech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b3d6bbae1d6d5638a4ab702ab195476787cde857 ]
During the IDPF init phase, the mailbox runs in poll mode until it is
configured to properly handle interrupts. The previous delay of 300ms is
excessively long for the mailbox polling mechanism, which causes a slow
initialization of ~2s:
echo 0000:06:12.4 > /sys/bus/pci/drivers/idpf/bind
[ 52.444239] idpf 0000:06:12.4: enabling device (0000 -> 0002)
[ 52.485005] idpf 0000:06:12.4: Device HW Reset initiated
[ 54.177181] idpf 0000:06:12.4: PTP init failed, err=-EOPNOTSUPP
[ 54.206177] idpf 0000:06:12.4: Minimum RX descriptor support not provided, using the default
[ 54.206182] idpf 0000:06:12.4: Minimum TX descriptor support not provided, using the default
Changing the delay to 300us avoids the delays during the initial mailbox
transactions, making the init phase much faster:
[ 83.342590] idpf 0000:06:12.4: enabling device (0000 -> 0002)
[ 83.384402] idpf 0000:06:12.4: Device HW Reset initiated
[ 83.518323] idpf 0000:06:12.4: PTP init failed, err=-EOPNOTSUPP
[ 83.547430] idpf 0000:06:12.4: Minimum RX descriptor support not provided, using the default
[ 83.547435] idpf 0000:06:12.4: Minimum TX descriptor support not provided, using the default
Fixes: 4930fbf419a7 ("idpf: add core init and interrupt request")
Signed-off-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6daa2893f323981c7894c68440823326e93a7d61 ]
There are off-by-one bugs when configuring RSS hash key and lookup
table, causing out-of-bounds reads to memory [1] and out-of-bounds
writes to device registers.
Before commit 43a3d9ba34c9 ("i40evf: Allow PF driver to configure RSS"),
the loop upper bounds were:
i <= I40E_VFQF_{HKEY,HLUT}_MAX_INDEX
which is safe since the value is the last valid index.
That commit changed the bounds to:
i <= adapter->rss_{key,lut}_size / 4
where `rss_{key,lut}_size / 4` is the number of dwords, so the last
valid index is `(rss_{key,lut}_size / 4) - 1`. Therefore, using `<=`
accesses one element past the end.
Fix the issues by using `<` instead of `<=`, ensuring we do not exceed
the bounds.
[1] KASAN splat about rss_key_size off-by-one
BUG: KASAN: slab-out-of-bounds in iavf_config_rss+0x619/0x800
Read of size 4 at addr ffff888102c50134 by task kworker/u8:6/63
CPU: 0 UID: 0 PID: 63 Comm: kworker/u8:6 Not tainted 6.18.0-rc2-enjuk-tnguy-00378-g3005f5b77652-dirty #156 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: iavf iavf_watchdog_task
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xb0
print_report+0x170/0x4f3
kasan_report+0xe1/0x1a0
iavf_config_rss+0x619/0x800
iavf_watchdog_task+0x2be7/0x3230
process_one_work+0x7fd/0x1420
worker_thread+0x4d1/0xd40
kthread+0x344/0x660
ret_from_fork+0x249/0x320
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 63:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
__kmalloc_noprof+0x246/0x6f0
iavf_watchdog_task+0x28fc/0x3230
process_one_work+0x7fd/0x1420
worker_thread+0x4d1/0xd40
kthread+0x344/0x660
ret_from_fork+0x249/0x320
ret_from_fork_asm+0x1a/0x30
The buggy address belongs to the object at ffff888102c50100
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 0 bytes to the right of
allocated 52-byte region [ffff888102c50100, ffff888102c50134)
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x102c50
flags: 0x200000000000000(node=0|zone=2)
page_type: f5(slab)
raw: 0200000000000000 ffff8881000418c0 dead000000000122 0000000000000000
raw: 0000000000000000 0000000080200020 00000000f5000000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888102c50000: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc
ffff888102c50080: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc
>ffff888102c50100: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
^
ffff888102c50180: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
ffff888102c50200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 43a3d9ba34c9 ("i40evf: Allow PF driver to configure RSS")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 69942834215323cd9131db557091b4dec43f19c5 ]
The maximum number of descriptors supported by the hardware is
hardware-dependent and can be retrieved using
i40e_get_max_num_descriptors(). Move this function to a shared header
and use it when checking for valid ring_len parameter rather than using
hardcoded value.
By fixing an over-acceptance issue, behavior change could be seen where
ring_len could now be rejected while configuring rx and tx queues if its
size is larger than the hardware-dependent maximum number of
descriptors.
Fixes: 55d225670def ("i40e: add validation for ring_len param")
Signed-off-by: Gregory Herrero <gregory.herrero@oracle.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit be43abc5514167cc129a8d8e9727b89b8e1d9719 ]
Add service task schedule to set_rx_mode.
In some cases there are error messages printed out in PTP application
(ptp4l):
ptp4l[13848.762]: port 1 (ens2f3np3): received SYNC without timestamp
ptp4l[13848.825]: port 1 (ens2f3np3): received SYNC without timestamp
ptp4l[13848.887]: port 1 (ens2f3np3): received SYNC without timestamp
This happens when service task would not run immediately after
set_rx_mode, and we need it for setup tasks. This service task checks, if
PTP RX packets are hung in firmware, and propagate correct settings such
as multicast address for IEEE 1588 Precision Time Protocol.
RX timestamping depends on some of these filters set. Bug happens only
with high PTP packets frequency incoming, and not every run since
sometimes service task is being ran from a different place immediately
after starting ptp4l.
Fixes: 0e4425ed641f ("i40e: fix: do not sleep in netdev_ops")
Reviewed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemyslaw Korba <przemyslaw.korba@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dd39edb445f07400e748da967a07d5dca5c5f96e ]
TID getting from ieee80211_get_tid() might be out of range of array size
of sta_entry->tids[], so check TID is less than MAX_TID_COUNT. Othwerwise,
UBSAN warn:
UBSAN: array-index-out-of-bounds in drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:514:30
index 10 is out of range for type 'rtl_tid_data [9]'
Fixes: 8ca4cdef9329 ("wifi: rtlwifi: rtl8192cu: Fix TX aggregation")
Signed-off-by: Morning Star <alexbestoso@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1764232628-13625-1-git-send-email-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3ccdfda345ca9a624ea425840a926b8338c1e25 ]
The indirect IO is necessary for RTL8822CS, but not necessary for other
chips. Otherwiese, it throws errors and becomes unusable.
rtw88_8723cs mmc1:0001:1: WOW Firmware version 11.0.0, H2C version 0
rtw88_8723cs mmc1:0001:1: Firmware version 11.0.0, H2C version 0
rtw88_8723cs mmc1:0001:1: sdio read32 failed (0xf0): -110
rtw88_8723cs mmc1:0001:1: sdio write8 failed (0x1c): -110
rtw88_8723cs mmc1:0001:1: sdio read32 failed (0xf0): -110
By vendor driver, only RTL8822CS and RTL8822ES need indirect IO, but
RTL8822ES isn't supported yet. Therefore, limit it to RTL8822CS only.
Reported-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/07a32e2d6c764eb1bd9415b5a921a652@realtek.com/T/#m997b4522f7209ba629561c776bfd1d13ab24c1d4
Fixes: 58de1f91e033 ("wifi: rtw88: sdio: use indirect IO for device registers before power-on")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Link: https://patch.msgid.link/1764034729-1251-1-git-send-email-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c4cdf7376271bce5714c06d79ec67759b18910eb upstream.
The local variable 'val' was never clamped to -75000 or 180000 because
the return value of clamp_val() was not used. Fix this by assigning the
clamped value back to 'val', and use clamp() instead of clamp_val().
Cc: stable@vger.kernel.org
Fixes: a557a92e6881 ("net: phy: marvell-88q2xxx: add support for temperature sensor")
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251202172743.453055-3-thorsten.blum@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd75c723ef566f7f009c047f47e0eee95fe348ab upstream.
Wake-on-Lan does currently not work for r8169 in DASH mode, e.g. the
ASUS Pro WS X570-ACE with RTL8168fp/RTL8117.
Fix by not returning early in rtl_prepare_power_down when dash_enabled.
While this fixes WoL, it still kills the OOB RTL8117 remote management
BMC connection. Fix by not calling rtl8168_driver_stop if WoL is enabled.
Fixes: 065c27c184d6 ("r8169: phy power ops")
Signed-off-by: René Rebe <rene@exactco.de>
Cc: stable@vger.kernel.org
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251202.194137.1647877804487085954.rene@exactco.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38b845e1f9e810869b0a0b69f202b877b7b7fb12 upstream.
The power-limits for ru and mcs and stored in the devicetree as bytewise
array (often with sizes which are not a multiple of 4). These arrays have a
prefix which defines for how many modes a line is applied. This prefix is
also only a byte - but the code still tried to fix the endianness of this
byte with a be32 operation. As result, loading was mostly failing or was
sending completely unexpected values to the firmware.
Since the other rates are also stored in the devicetree as bytewise arrays,
just drop the u32 access + be32_to_cpu conversion and directly access them
as bytes arrays.
Cc: stable@vger.kernel.org
Fixes: 22b980badc0f ("mt76: add functions for parsing rate power limits from DT")
Fixes: a9627d992b5e ("mt76: extend DT rate power limits to support 11ax devices")
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e54d3b4a8437b6783d4145c86962a2aa51022f3 upstream.
Commit 2603be9e8167 ("can: gs_usb: gs_can_open(): improve error handling")
added missing error handling to the gs_can_open() function.
The driver uses 2 USB anchors to track the allocated URBs: the TX URBs in
struct gs_can::tx_submitted for each netdev and the RX URBs in struct
gs_usb::rx_submitted for the USB device. gs_can_open() allocates the RX
URBs, while TX URBs are allocated during gs_can_start_xmit().
The cleanup in gs_can_open() kills all anchored dev->tx_submitted
URBs (which is not necessary since the netdev is not yet registered), but
misses the parent->rx_submitted URBs.
Fix the problem by killing the rx_submitted instead of the tx_submitted.
Fixes: 2603be9e8167 ("can: gs_usb: gs_can_open(): improve error handling")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251210-gs_usb-fix-error-handling-v1-1-d6a5a03f10bb@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
