| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 2eca98e5b24d01c02b46c67be05a5f98cc9789b1 ]
Issue the same error message in case an illegal page boundary crossing
has been detected in both cases where this is tested.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20230329080259.14823-1-jgross@suse.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 45977e58ce65ed0459edc9a0466d9dfea09463f5 ]
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 67d47b95119ad589b0a0b16b88b1dd9a04061ced ]
While using i219-LM card currently it was only possible to achieve
about 60% of maximum speed due to regression introduced in Linux 5.8.
This was caused by TSO not being disabled by default despite commit
f29801030ac6 ("e1000e: Disable TSO for buffer overrun workaround").
Fix that by disabling TSO during driver probe.
Fixes: f29801030ac6 ("e1000e: Disable TSO for buffer overrun workaround")
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230417205345.1030801-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1f64757ee2bb22a93ec89b4c71707297e8cca0ba ]
During initialization the driver issues a reset command via its command
interface in order to remove previous configuration from the device.
After issuing the reset, the driver waits for 200ms before polling on
the "system_status" register using memory-mapped IO until the device
reaches a ready state (0x5E). The wait is necessary because the reset
command only triggers the reset, but the reset itself happens
asynchronously. If the driver starts polling too soon, the read of the
"system_status" register will never return and the system will crash
[1].
The issue was discovered when the device was flashed with a development
firmware version where the reset routine took longer to complete. The
issue was fixed in the firmware, but it exposed the fact that the
current wait time is borderline.
Fix by increasing the wait time from 200ms to 400ms. With this patch and
the buggy firmware version, the issue did not reproduce in 10 reboots
whereas without the patch the issue is reproduced quite consistently.
[1]
mce: CPUs not responding to MCE broadcast (may include false positives): 0,4
mce: CPUs not responding to MCE broadcast (may include false positives): 0,4
Kernel panic - not syncing: Timeout: Not all CPUs entered broadcast exception handler
Shutting down cpus with NMI
Kernel Offset: 0x12000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
Fixes: ac004e84164e ("mlxsw: pci: Wait longer before accessing the device after reset")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c484fcc058bada604d7e4e5228d4affb646ddbc2 ]
When a net device is put administratively up, its 'IFF_UP' flag is set
(if not set already) and a 'NETDEV_UP' notification is emitted, which
causes the 8021q driver to add VLAN ID 0 on the device. The reverse
happens when a net device is put administratively down.
When changing the type of a bond to Ethernet, its 'IFF_UP' flag is
incorrectly cleared, resulting in the kernel skipping the above process
and VLAN ID 0 being leaked [1].
Fix by restoring the flag when changing the type to Ethernet, in a
similar fashion to the restoration of the 'IFF_SLAVE' flag.
The issue can be reproduced using the script in [2], with example out
before and after the fix in [3].
[1]
unreferenced object 0xffff888103479900 (size 256):
comm "ip", pid 329, jiffies 4294775225 (age 28.561s)
hex dump (first 32 bytes):
00 a0 0c 15 81 88 ff ff 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff81a6051a>] kmalloc_trace+0x2a/0xe0
[<ffffffff8406426c>] vlan_vid_add+0x30c/0x790
[<ffffffff84068e21>] vlan_device_event+0x1491/0x21a0
[<ffffffff81440c8e>] notifier_call_chain+0xbe/0x1f0
[<ffffffff8372383a>] call_netdevice_notifiers_info+0xba/0x150
[<ffffffff837590f2>] __dev_notify_flags+0x132/0x2e0
[<ffffffff8375ad9f>] dev_change_flags+0x11f/0x180
[<ffffffff8379af36>] do_setlink+0xb96/0x4060
[<ffffffff837adf6a>] __rtnl_newlink+0xc0a/0x18a0
[<ffffffff837aec6c>] rtnl_newlink+0x6c/0xa0
[<ffffffff837ac64e>] rtnetlink_rcv_msg+0x43e/0xe00
[<ffffffff839a99e0>] netlink_rcv_skb+0x170/0x440
[<ffffffff839a738f>] netlink_unicast+0x53f/0x810
[<ffffffff839a7fcb>] netlink_sendmsg+0x96b/0xe90
[<ffffffff8369d12f>] ____sys_sendmsg+0x30f/0xa70
[<ffffffff836a6d7a>] ___sys_sendmsg+0x13a/0x1e0
unreferenced object 0xffff88810f6a83e0 (size 32):
comm "ip", pid 329, jiffies 4294775225 (age 28.561s)
hex dump (first 32 bytes):
a0 99 47 03 81 88 ff ff a0 99 47 03 81 88 ff ff ..G.......G.....
81 00 00 00 01 00 00 00 cc cc cc cc cc cc cc cc ................
backtrace:
[<ffffffff81a6051a>] kmalloc_trace+0x2a/0xe0
[<ffffffff84064369>] vlan_vid_add+0x409/0x790
[<ffffffff84068e21>] vlan_device_event+0x1491/0x21a0
[<ffffffff81440c8e>] notifier_call_chain+0xbe/0x1f0
[<ffffffff8372383a>] call_netdevice_notifiers_info+0xba/0x150
[<ffffffff837590f2>] __dev_notify_flags+0x132/0x2e0
[<ffffffff8375ad9f>] dev_change_flags+0x11f/0x180
[<ffffffff8379af36>] do_setlink+0xb96/0x4060
[<ffffffff837adf6a>] __rtnl_newlink+0xc0a/0x18a0
[<ffffffff837aec6c>] rtnl_newlink+0x6c/0xa0
[<ffffffff837ac64e>] rtnetlink_rcv_msg+0x43e/0xe00
[<ffffffff839a99e0>] netlink_rcv_skb+0x170/0x440
[<ffffffff839a738f>] netlink_unicast+0x53f/0x810
[<ffffffff839a7fcb>] netlink_sendmsg+0x96b/0xe90
[<ffffffff8369d12f>] ____sys_sendmsg+0x30f/0xa70
[<ffffffff836a6d7a>] ___sys_sendmsg+0x13a/0x1e0
[2]
ip link add name t-nlmon type nlmon
ip link add name t-dummy type dummy
ip link add name t-bond type bond mode active-backup
ip link set dev t-bond up
ip link set dev t-nlmon master t-bond
ip link set dev t-nlmon nomaster
ip link show dev t-bond
ip link set dev t-dummy master t-bond
ip link show dev t-bond
ip link del dev t-bond
ip link del dev t-dummy
ip link del dev t-nlmon
[3]
Before:
12: t-bond: <NO-CARRIER,BROADCAST,MULTICAST,MASTER,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default qlen 1000
link/netlink
12: t-bond: <BROADCAST,MULTICAST,MASTER,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether 46:57:39:a4:46:a2 brd ff:ff:ff:ff:ff:ff
After:
12: t-bond: <NO-CARRIER,BROADCAST,MULTICAST,MASTER,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default qlen 1000
link/netlink
12: t-bond: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether 66:48:7b:74:b6:8a brd ff:ff:ff:ff:ff:ff
Fixes: e36b9d16c6a6 ("bonding: clean muticast addresses when device changes type")
Fixes: 75c78500ddad ("bonding: remap muticast addresses without using dev_close() and dev_open()")
Fixes: 9ec7eb60dcbc ("bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change")
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Link: https://lore.kernel.org/netdev/78a8a03b-6070-3e6b-5042-f848dab16fb8@alu.unizg.hr/
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c0e73276f0fcbbd3d4736ba975d7dc7a48791b0c ]
Function mlxfw_mfa2_tlv_multi_get() returns NULL if 'tlv' in
question does not pass checks in mlxfw_mfa2_tlv_payload_get(). This
behaviour may lead to NULL pointer dereference in 'multi->total_len'.
Fix this issue by testing mlxfw_mfa2_tlv_multi_get()'s return value
against NULL.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process")
Co-developed-by: Natalia Petrova <n.petrova@fintech.ru>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230417120718.52325-1-n.zhandarovich@fintech.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8b51a1a15d5a3cce231e0669f6a161dc5bb9b75 ]
The driver does not support PTP on these older chips and it is assuming
that firmware on these older chips will not return the
PORT_MAC_PTP_QCFG_RESP_FLAGS_HWRM_ACCESS flag in __bnxt_hwrm_ptp_qcfg(),
causing the function to abort quietly.
But newer firmware now sets this flag and so __bnxt_hwrm_ptp_qcfg()
will proceed further. Eventually it will fail in bnxt_ptp_init() ->
bnxt_map_ptp_regs() because there is no code to support the older chips.
The driver will then complain:
"PTP initialization failed.\n"
Fix it so that we abort quietly earlier without going through the
unnecessary steps and alarming the user with the warning log.
Fixes: ae5c42f0b92c ("bnxt_en: Get PTP hardware capability from firmware")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c86c00c6935505929cc9adb29ddb85e48c71f828 ]
Add error handling of i40e_setup_misc_vector() in i40e_rebuild().
In case interrupt vectors setup fails do not re-open vsi-s and
do not bring up vf-s, we have no interrupts to serve a traffic
anyway.
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8485d093b076e59baff424552e8aecfc5bd2d261 ]
Fix accessing vsi->active_filters without holding the mac_filter_hash_lock.
Move vsi->active_filters = 0 inside critical section and
move clear_bit(__I40E_VSI_OVERFLOW_PROMISC, vsi->state) after the critical
section to ensure the new filters from other threads can be added only after
filters cleaning in the critical section is finished.
Fixes: 278e7d0b9d68 ("i40e: store MAC/VLAN filters in a hash with the MAC Address as key")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a80bb8e7233b2ad6ff119646b6e33fb3edcec37b ]
There is a use-after-free scenario that is:
When the NIC is down, user set mac address or vlan tag to VF,
the xxx_set_vf_mac() or xxx_set_vf_vlan() will invoke efx_net_stop()
and efx_net_open(), since netif_running() is false, the port will not
start and keep port_enabled false, but selftest_work is scheduled
in efx_net_open().
If we remove the device before selftest_work run, the efx_stop_port()
will not be called since the NIC is down, and then efx is freed,
we will soon get a UAF in run_timer_softirq() like this:
[ 1178.907941] ==================================================================
[ 1178.907948] BUG: KASAN: use-after-free in run_timer_softirq+0xdea/0xe90
[ 1178.907950] Write of size 8 at addr ff11001f449cdc80 by task swapper/47/0
[ 1178.907950]
[ 1178.907953] CPU: 47 PID: 0 Comm: swapper/47 Kdump: loaded Tainted: G O --------- -t - 4.18.0 #1
[ 1178.907954] Hardware name: SANGFOR X620G40/WI2HG-208T1061A, BIOS SPYH051032-U01 04/01/2022
[ 1178.907955] Call Trace:
[ 1178.907956] <IRQ>
[ 1178.907960] dump_stack+0x71/0xab
[ 1178.907963] print_address_description+0x6b/0x290
[ 1178.907965] ? run_timer_softirq+0xdea/0xe90
[ 1178.907967] kasan_report+0x14a/0x2b0
[ 1178.907968] run_timer_softirq+0xdea/0xe90
[ 1178.907971] ? init_timer_key+0x170/0x170
[ 1178.907973] ? hrtimer_cancel+0x20/0x20
[ 1178.907976] ? sched_clock+0x5/0x10
[ 1178.907978] ? sched_clock_cpu+0x18/0x170
[ 1178.907981] __do_softirq+0x1c8/0x5fa
[ 1178.907985] irq_exit+0x213/0x240
[ 1178.907987] smp_apic_timer_interrupt+0xd0/0x330
[ 1178.907989] apic_timer_interrupt+0xf/0x20
[ 1178.907990] </IRQ>
[ 1178.907991] RIP: 0010:mwait_idle+0xae/0x370
If the NIC is not actually brought up, there is no need to schedule
selftest_work, so let's move invoking efx_selftest_async_start()
into efx_start_all(), and it will be canceled by broughting down.
Fixes: dd40781e3a4e ("sfc: Run event/IRQ self-test asynchronously when interface is brought up")
Fixes: e340be923012 ("sfc: add ndo_set_vf_mac() function for EF10")
Debugged-by: Huang Cun <huangcun@sangfor.com.cn>
Cc: Donglin Peng <pengdonglin@sangfor.com.cn>
Suggested-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 853618d5886bf94812f31228091cd37d308230f7 ]
Here we copy the data from the original buf to the new page. But we
not check that it may be overflow.
As long as the size received(including vnethdr) is greater than 3840
(PAGE_SIZE -VIRTIO_XDP_HEADROOM). Then the memcpy will overflow.
And this is completely possible, as long as the MTU is large, such
as 4096. In our test environment, this will cause crash. Since crash is
caused by the written memory, it is meaningless, so I do not include it.
Fixes: 72979a6c3590 ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit bdaaecc127d471c422ee9e994978617c8aa79e1e upstream.
Any multiplication between GENMASK(31, 0) and a number bigger than 1
will be truncated because of the overflow, if the size of unsigned long
is 32 bits.
Replaced GENMASK with GENMASK_ULL to make sure that multiplication will
be between 64 bits values.
Cc: <stable@vger.kernel.org> # 5.15+
Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095953.75622-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4506722dc39ca840593f14e3faa4c9ba9408211 upstream.
Unregister PTP clock when the driver is removed.
Purge the RX and TX skb queues.
Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095904.75456-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 813c2dd78618f108fdcf9cd726ea90f081ee2881 upstream.
sfp->i2c_block_size is initialized at SFP module insertion in
sfp_sm_mod_probe(). Because of that, if SFP module was never inserted
since boot, sfp_read() call will lead to zero-length I2C read attempt,
and not all I2C controllers are happy with zero-length reads.
One way to issue sfp_read() on empty SFP cage is to execute ethtool -m.
If SFP module was never plugged since boot, there will be a zero-length
I2C read attempt.
# ethtool -m xge0
i2c i2c-3: adapter quirk: no zero length (addr 0x0050, size 0, read)
Cannot get Module EEPROM data: Operation not supported
If SFP module was plugged then removed at least once,
sfp->i2c_block_size will be initialized and ethtool -m will fail with
different exit code and without I2C error
# ethtool -m xge0
Cannot get Module EEPROM data: Remote I/O error
Fix this by initializing sfp->i2_block_size at struct sfp allocation
stage so no wild sfp_read() could issue zero-length I2C read.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Fixes: 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 923bf981eb6ecc027227716e30701bdcc1845fbf ]
Some recent upstream debugging uncovered the fact that in
iwlwifi, the TXQ list manipulation is racy.
Introduce a new state bit for when the TXQ is completely
ready and can be used without locking, and if that's not
set yet acquire the lock to check everything correctly.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b58e3d4311b54b6dd0e37165277965da0c9eb21d ]
This could race if the queue is redirected while full, then
the flushing internally would start it while it's not yet
usable again. Fix it by using two state bits instead of just
one.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 139f6973bf140c65d4d1d4bde5485badb4454d7a ]
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/net/wireless/marvell/mwifiex/sdio.c:498:34: error: ‘mwifiex_sdio_of_match_table’ defined but not used [-Werror=unused-const-variable=]
drivers/net/wireless/marvell/mwifiex/pcie.c:175:34: error: ‘mwifiex_pcie_of_match_table’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230312132523.352182-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8b74453555872851bdd7ea43a7c0ec39659834f ]
For quite some time we were chasing a bug which looked like a sudden
permanent failure of networking and mmc on some of our devices.
The bug was very sensitive to any software changes and even more to
any kernel debug options.
Finally we got a setup where the problem was reproducible with
CONFIG_DMA_API_DEBUG=y and it revealed the issue with the rx dma:
[ 16.992082] ------------[ cut here ]------------
[ 16.996779] DMA-API: macb ff0b0000.ethernet: device driver tries to free DMA memory it has not allocated [device address=0x0000000875e3e244] [size=1536 bytes]
[ 17.011049] WARNING: CPU: 0 PID: 85 at kernel/dma/debug.c:1011 check_unmap+0x6a0/0x900
[ 17.018977] Modules linked in: xxxxx
[ 17.038823] CPU: 0 PID: 85 Comm: irq/55-8000f000 Not tainted 5.4.0 #28
[ 17.045345] Hardware name: xxxxx
[ 17.049528] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 17.054322] pc : check_unmap+0x6a0/0x900
[ 17.058243] lr : check_unmap+0x6a0/0x900
[ 17.062163] sp : ffffffc010003c40
[ 17.065470] x29: ffffffc010003c40 x28: 000000004000c03c
[ 17.070783] x27: ffffffc010da7048 x26: ffffff8878e38800
[ 17.076095] x25: ffffff8879d22810 x24: ffffffc010003cc8
[ 17.081407] x23: 0000000000000000 x22: ffffffc010a08750
[ 17.086719] x21: ffffff8878e3c7c0 x20: ffffffc010acb000
[ 17.092032] x19: 0000000875e3e244 x18: 0000000000000010
[ 17.097343] x17: 0000000000000000 x16: 0000000000000000
[ 17.102647] x15: ffffff8879e4a988 x14: 0720072007200720
[ 17.107959] x13: 0720072007200720 x12: 0720072007200720
[ 17.113261] x11: 0720072007200720 x10: 0720072007200720
[ 17.118565] x9 : 0720072007200720 x8 : 000000000000022d
[ 17.123869] x7 : 0000000000000015 x6 : 0000000000000098
[ 17.129173] x5 : 0000000000000000 x4 : 0000000000000000
[ 17.134475] x3 : 00000000ffffffff x2 : ffffffc010a1d370
[ 17.139778] x1 : b420c9d75d27bb00 x0 : 0000000000000000
[ 17.145082] Call trace:
[ 17.147524] check_unmap+0x6a0/0x900
[ 17.151091] debug_dma_unmap_page+0x88/0x90
[ 17.155266] gem_rx+0x114/0x2f0
[ 17.158396] macb_poll+0x58/0x100
[ 17.161705] net_rx_action+0x118/0x400
[ 17.165445] __do_softirq+0x138/0x36c
[ 17.169100] irq_exit+0x98/0xc0
[ 17.172234] __handle_domain_irq+0x64/0xc0
[ 17.176320] gic_handle_irq+0x5c/0xc0
[ 17.179974] el1_irq+0xb8/0x140
[ 17.183109] xiic_process+0x5c/0xe30
[ 17.186677] irq_thread_fn+0x28/0x90
[ 17.190244] irq_thread+0x208/0x2a0
[ 17.193724] kthread+0x130/0x140
[ 17.196945] ret_from_fork+0x10/0x20
[ 17.200510] ---[ end trace 7240980785f81d6f ]---
[ 237.021490] ------------[ cut here ]------------
[ 237.026129] DMA-API: exceeded 7 overlapping mappings of cacheline 0x0000000021d79e7b
[ 237.033886] WARNING: CPU: 0 PID: 0 at kernel/dma/debug.c:499 add_dma_entry+0x214/0x240
[ 237.041802] Modules linked in: xxxxx
[ 237.061637] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.4.0 #28
[ 237.068941] Hardware name: xxxxx
[ 237.073116] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[ 237.077900] pc : add_dma_entry+0x214/0x240
[ 237.081986] lr : add_dma_entry+0x214/0x240
[ 237.086072] sp : ffffffc010003c30
[ 237.089379] x29: ffffffc010003c30 x28: ffffff8878a0be00
[ 237.094683] x27: 0000000000000180 x26: ffffff8878e387c0
[ 237.099987] x25: 0000000000000002 x24: 0000000000000000
[ 237.105290] x23: 000000000000003b x22: ffffffc010a0fa00
[ 237.110594] x21: 0000000021d79e7b x20: ffffffc010abe600
[ 237.115897] x19: 00000000ffffffef x18: 0000000000000010
[ 237.121201] x17: 0000000000000000 x16: 0000000000000000
[ 237.126504] x15: ffffffc010a0fdc8 x14: 0720072007200720
[ 237.131807] x13: 0720072007200720 x12: 0720072007200720
[ 237.137111] x11: 0720072007200720 x10: 0720072007200720
[ 237.142415] x9 : 0720072007200720 x8 : 0000000000000259
[ 237.147718] x7 : 0000000000000001 x6 : 0000000000000000
[ 237.153022] x5 : ffffffc010003a20 x4 : 0000000000000001
[ 237.158325] x3 : 0000000000000006 x2 : 0000000000000007
[ 237.163628] x1 : 8ac721b3a7dc1c00 x0 : 0000000000000000
[ 237.168932] Call trace:
[ 237.171373] add_dma_entry+0x214/0x240
[ 237.175115] debug_dma_map_page+0xf8/0x120
[ 237.179203] gem_rx_refill+0x190/0x280
[ 237.182942] gem_rx+0x224/0x2f0
[ 237.186075] macb_poll+0x58/0x100
[ 237.189384] net_rx_action+0x118/0x400
[ 237.193125] __do_softirq+0x138/0x36c
[ 237.196780] irq_exit+0x98/0xc0
[ 237.199914] __handle_domain_irq+0x64/0xc0
[ 237.204000] gic_handle_irq+0x5c/0xc0
[ 237.207654] el1_irq+0xb8/0x140
[ 237.210789] arch_cpu_idle+0x40/0x200
[ 237.214444] default_idle_call+0x18/0x30
[ 237.218359] do_idle+0x200/0x280
[ 237.221578] cpu_startup_entry+0x20/0x30
[ 237.225493] rest_init+0xe4/0xf0
[ 237.228713] arch_call_rest_init+0xc/0x14
[ 237.232714] start_kernel+0x47c/0x4a8
[ 237.236367] ---[ end trace 7240980785f81d70 ]---
Lars was fast to find an explanation: according to the datasheet
bit 2 of the rx buffer descriptor entry has a different meaning in the
extended mode:
Address [2] of beginning of buffer, or
in extended buffer descriptor mode (DMA configuration register [28] = 1),
indicates a valid timestamp in the buffer descriptor entry.
The macb driver didn't mask this bit while getting an address and it
eventually caused a memory corruption and a dma failure.
The problem is resolved by explicitly clearing the problematic bit
if hw timestamping is used.
Fixes: 7b4296148066 ("net: macb: Add support for PTP timestamps in DMA descriptors")
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Co-developed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230412232144.770336-1-roman.gushchin@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a56ef25619e079bd7d744636cf18d054d1e91982 ]
Smatch reports:
drivers/net/wwan/iosm/iosm_ipc_pcie.c:298 ipc_pcie_probe()
warn: missing unwind goto?
When dma_set_mask fails it directly returns without disabling pci
device and freeing ipc_pcie. Fix this my calling a correct goto label
As dma_set_mask returns either 0 or -EIO, we can use a goto label, as
it finally returns -EIO.
Add a set_mask_fail goto label which stands consistent with other goto
labels in this function..
Fixes: 035e3befc191 ("net: wwan: iosm: fix driver not working with INTEL_IOMMU disabled")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7573099e10ca69c3be33995c1fcd0d241226816d ]
Static code analyzer complains to unchecked return value.
The result of pci_reset_function() is unchecked.
Despite, the issue is on the FLR supported code path and in that
case reset can be done with pcie_flr(), the patch uses less invasive
approach by adding the result check of pci_reset_function().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7e2cf4feba05 ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c85b7fa12ef2e4fc11a4e31ac595fb5f9d0ddf9 ]
The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:
while [ $((i++)) ]
ip l add l eth0 name eth0.$i type vlan id $i
we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.
On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.
This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
delete the VLAN.
Fixes: 48ccc43ecf10 ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0c0da0e951053fda20412cd284e2714bbbb31bff ]
The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.
Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 9c85b7fa12ef ("iavf: remove active_cvlans and active_svlans bitmaps")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4598380f9c548aa161eb4e990a1583f0a7d1e0d7 ]
When arp_validate is set to 2, 3, or 6, validation is performed for
backup slaves as well. As stated in the bond documentation, validation
involves checking the broadcast ARP request sent out via the active
slave. This helps determine which slaves are more likely to function in
the event of an active slave failure.
However, when the target is an IPv6 address, the NS message sent from
the active interface is not checked on backup slaves. Additionally,
based on the bond_arp_rcv() rule b, we must reverse the saddr and daddr
when checking the NS message.
Note that when checking the NS message, the destination address is a
multicast address. Therefore, we must convert the target address to
solicited multicast in the bond_get_targets_ip6() function.
Prior to the fix, the backup slaves had a mii status of "down", but
after the fix, all of the slaves' mii status was updated to "UP".
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ce07be703456acb00e83d99f3b8036252c33b02 ]
Smatch reports: drivers/net/ethernet/sun/niu.c:4525
niu_alloc_channels() warn: missing unwind goto?
If niu_rbr_fill() fails, then we are directly returning 'err' without
freeing the channels.
Fix this by changing direct return to a goto 'out_err'.
Fixes: a3138df9f20e ("[NIU]: Add Sun Neptune ethernet driver.")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e6db67fa871dee37d22701daba806bfcd4d9df49 upstream.
This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330091259.61378-1-nbd@nbd.name
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24e3fce00c0b557491ff596c0682a29dee6fe848 upstream.
Queue reset was moved out from __init_dma_rx_desc_rings() and
__init_dma_tx_desc_rings() functions. Thus, the driver fails to transmit
and receive packet after XDP prog setup.
This commit adds the missing queue reset into stmmac_xdp_open() function.
Fixes: f9ec5723c3db ("net: ethernet: stmicro: stmmac: move queue reset to dedicated functions")
Cc: <stable@vger.kernel.org> # 6.0+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230404044823.3226144-1-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8fbc10b995a506e173f1080dfa2764f232a65e02 ]
Some DT devices already have phy device configured in the DT/ACPI.
Current implementation scans for a phy unconditionally even though
there is a phy listed in the DT/ACPI and already attached.
We should check the fwnode if there is any phy device listed in
fwnode and decide whether to scan for a phy to attach to.
Fixes: fe2cfbc96803 ("net: stmmac: check if MAC needs to attach to a PHY")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/lkml/20230403212434.296975-1-martin.blumenstingl@googlemail.com/
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Shahab Vahedi <shahab@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Link: https://lore.kernel.org/r/20230406024541.3556305-1-michael.wei.hong.sit@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3ce9345580974863c060fa32971537996a7b2d57 ]
Non-GSO TCP packets whose SKBs' linear portion did not include the
entire TCP header were not populating the first Tx descriptor with
as many bytes as the vNIC expected. This change ensures that all
TCP packets populate the first descriptor with the correct number of
bytes.
Fixes: 893ce44df565 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Shailend Chand <shailend@google.com>
Link: https://lore.kernel.org/r/20230403172809.2939306-1-shailend@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 83c911dc5e0e8e6eaa6431c06972a8f159bfe2fc ]
Reset the FDIR counters when FDIR inits. Without this patch,
when VF initializes or resets, all the FDIR counters are not
cleaned, which may cause unexpected behaviors for future FDIR
rule create (e.g., rule conflict).
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Lingyu Liu <lingyu.liu@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b4a01ace20f5c93c724abffc0a83ec84f514b98d ]
When adding a FDIR filter, if ice_vc_fdir_set_irq_ctx returns failure,
the inserted fdir entry will not be removed and if ice_vc_fdir_write_fltr
returns failure, the fdir context info for irq handler will not be cleared
which may lead to inconsistent or memory leak issue. This patch refines
failure cases to resolve this issue.
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Simei Su <simei.su@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 218c597325f4faf7b7a6049233a30d7842b5b2dc ]
stmmac_reinit_queues() fails to fix up the RX hash. Even if the number
of channels gets restricted, the output of `ethtool -x' indicates that
all RX queues are used:
$ ethtool -l enp0s29f2
Channel parameters for enp0s29f2:
Pre-set maximums:
RX: 8
TX: 8
Other: n/a
Combined: n/a
Current hardware settings:
RX: 8
TX: 8
Other: n/a
Combined: n/a
$ ethtool -x enp0s29f2
RX flow hash indirection table for enp0s29f2 with 8 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 0 1 2 3 4 5 6 7
[...]
$ ethtool -L enp0s29f2 rx 3
$ ethtool -x enp0s29f2
RX flow hash indirection table for enp0s29f2 with 3 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 0 1 2 3 4 5 6 7
[...]
Fix this by setting the indirection table according to the number
of specified queues. The result is now as expected:
$ ethtool -L enp0s29f2 rx 3
$ ethtool -x enp0s29f2
RX flow hash indirection table for enp0s29f2 with 3 RX ring(s):
0: 0 1 2 0 1 2 0 1
8: 2 0 1 2 0 1 2 0
[...]
Tested on Intel Elkhart Lake.
Fixes: 0366f7e06a6b ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Link: https://lore.kernel.org/r/20230403121120.489138-1-vinschen@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c6b486fb33680ad5a3a6390ce693c835caaae3f7 ]
In the am65_cpsw_nuss_probe() function's cleanup path, the call to
of_platform_device_destroy() for the common->mdio_dev device is invoked
unconditionally. It is possible that either the MDIO node is not present
in the device-tree, or the MDIO node is disabled in the device-tree. In
both these cases, the MDIO device is not created, resulting in a NULL
pointer dereference when the of_platform_device_destroy() function is
invoked on the common->mdio_dev device on the cleanup path.
Fix this by ensuring that the common->mdio_dev device exists, before
attempting to invoke of_platform_device_destroy().
Fixes: a45cfcc69a25 ("net: ethernet: ti: am65-cpsw-nuss: use of_platform_device_create() for mdio")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230403090321.835877-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 089b91a0155c4de1209a07ff2a7dd299ff3ece47 ]
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e4efa515d58f1363d8a27e548f9c5769d3121e03 ]
After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
unless WOWL is used"), the wifi adapter by default is turned off on suspend
and then re-probed on resume.
In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
the newly added re-probe on resume fails like this:
brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
ieee80211 phy1: brcmf_bus_started: failed: -110
ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
It seems this specific brcmfmac model does not like being reprobed without
it actually being turned off first.
And the adapter is not being turned off during suspend because of
commit f0992ace680c ("brcmfmac: prohibit ACPI power management for brcmfmac
driver").
Now that the driver is being reprobed on resume, the disabling of ACPI
pm is no longer necessary, except when WOWL is used (in which case there
is no-reprobe).
Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
the brcmfmac43430a1 suspend/resume regression and should help save some
power when suspended.
This change means that the code now also may re-enable ACPI pm when WOWL
gets disabled. ACPI pm should only be re-enabled if it was enabled by
the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
to save the original state for this.
This has been tested on the following devices:
Asus T100TA brcmfmac43241b4-sdio
Acer Iconia One 7 B1-750 brcmfmac43340-sdio
Chuwi Hi8 brcmfmac43430a0-sdio
Chuwi Hi8 brcmfmac43430a1-sdio
(the Asus T100TA is the device for which the prohibiting of ACPI pm
was originally added)
Fixes: 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used")
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320122252.240070-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6fc21a6ed5953b1dd3a41ce7be1ea57f5ef8c081 ]
Currently, intel_speed_mode_2500() will fix-up xpcs_an_inband
to 1 if the underlying controller has a max speed of 1000Mbps.
The value has been initialized and modified if it is
a fixed-linked setup earlier.
This patch removes the fix-up to allow for fixed-linked setup
support. In stmmac_phy_setup(), ovr_an_inband is set based on
the value of xpcs_an_inband. Which in turn will return an
error in phylink_parse_mode() where MLO_AN_FIXED and
ovr_an_inband are both set.
Fixes: c82386310d95 ("stmmac: intel: prepare to support 1000BASE-X phy interface setting")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fe2cfbc9680356a3d9f8adde8a38e715831e32f5 ]
After the introduction of the fixed-link support, the MAC driver
no longer attempt to scan for a PHY to attach to. This causes the
non fixed-link setups to stop working.
Using the phylink_expects_phy() to check and determine if the MAC
should expect and attach a PHY.
Fixes: ab21cf920928 ("net: stmmac: make mdio register skips PHY scanning for fixed-link")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Lai Peter Jun Ann <peter.jun.ann.lai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 653a180957a85c3fc30320cc7e84f5dc913a64f8 ]
Provide phylink_expects_phy() to allow MAC drivers to check if it
is expecting a PHY to attach to. Since fixed-linked setups do not
need to attach to a PHY.
Provides a boolean value as to if the MAC should expect a PHY.
Returns true if a PHY is expected.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fe2cfbc96803 ("net: stmmac: check if MAC needs to attach to a PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9e3d9ae52b5657399a7b61258cc7482434a911bb upstream.
It is possible to trigger these VTU violation messages very easily,
it's only necessary to send packets with an unknown VLAN ID to a port
that belongs to a VLAN-aware bridge.
Do a similar thing as for ATU violation messages, and hide them in the
kernel's trace buffer.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_vtu_miss_violation
mv88e6xxx:mv88e6xxx_vtu_member_violation
$ trace-cmd report
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8646384d80f3d3b4a66b3284dbbd8232d1b8799e upstream.
In applications where the switch ports must perform 802.1X based
authentication and are therefore locked, ATU violation interrupts are
quite to be expected as part of normal operation. The problem is that
they currently spam the kernel log, even if rate limited.
Create a series of trace points, all derived from the same event class,
which log these violations to the kernel's trace buffer, which is both
much faster and much easier to ignore than printing to a serial console.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_atu_full_violation
mv88e6xxx:mv88e6xxx_atu_miss_violation
mv88e6xxx:mv88e6xxx_atu_member_violation
$ trace-cmd record -e mv88e6xxx sleep 10
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4bf24ad09bc0b05e97fb48b962b2c9246fc76727 upstream.
When an ATU violation occurs, the switch uses the ATU FID register to
report the FID of the MAC address that incurred the violation. It would
be good for the driver to know the FID value for purposes such as
logging and CPU-based authentication.
Up until now, the driver has been calling the mv88e6xxx_g1_atu_op()
function to read ATU violations, but that doesn't do exactly what we
want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0.
(side note, the documentation for the ATU Get/Clear Violation command
says that writes to the ATU FID register have no effect before the
operation starts, it's only that we disregard the value that this
register provides once the operation completes)
So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather
mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need
to write it.
The remainder of mv88e6xxx_g1_atu_op() except for
mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a
GET_CLR_VIOLATION command to the ATU. In principle we could have still
kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID
register are pointless, but in the interest of doing less CPU work per
interrupt, write a new function called mv88e6xxx_g1_read_atu_violation()
and call it.
The FID will be the port default FID as set by mv88e6xxx_port_set_fid()
if the VID from the packet cannot be found in the VTU. Otherwise it is
the FID derived from the VTU entry associated with that VID.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82e2c39f9ef78896e9b634dfd82dc042e6956bb7 upstream.
dp83869 internally uses a look-up table for mapping supported delays in
nanoseconds to register values.
When specific delays are defined in device-tree, phy_get_internal_delay
does the lookup automatically returning an index.
The default case wrongly assigns the nanoseconds value from the lookup
table, resulting in numeric value 2000 applied to delay configuration
register, rather than the expected index values 0-7 (7 for 2000).
Ultimately this issue broke RX for 1Gbps links.
Fix default delay configuration by assigning the intended index value
directly.
Cc: stable@vger.kernel.org
Fixes: 736b25afe284 ("net: dp83869: Add RGMII internal delay configuration")
Co-developed-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323102536.31988-1-josua@solid-run.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 05310f31ca74673a96567fb14637b7d5d6c82ea5 upstream.
Fix xenvif_get_requests() not to do grant copy operations across local
page boundaries. This requires to double the maximum number of copy
operations per queue, as each copy could now be split into 2.
Make sure that struct xenvif_tx_cb doesn't grow too large.
Cc: stable@vger.kernel.org
Fixes: ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3bced313b9a5a237c347e0f079c8c2fe4b3935aa upstream.
Currently, vmxnet3 uses GRO callback only if LRO is disabled. However,
on smartNic based setups where UPT is supported, LRO can be enabled
from guest VM but UPT devicve does not support LRO as of now. In such
cases, there can be performance degradation as GRO is not being done.
This patch fixes this issue by calling GRO API when UPT is enabled. We
use updateRxProd to determine if UPT mode is active or not.
To clarify few things discussed over the thread:
The patch is not neglecting any feature bits nor disabling GRO. It uses
GRO callback when UPT is active as LRO is not available in UPT.
GRO callback cannot be used as default for all cases as it degrades
performance for non-UPT cases or for cases when LRO is already done in
ESXi.
Cc: stable@vger.kernel.org
Fixes: 6f91f4ba046e ("vmxnet3: add support for capability registers")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323200721.27622-1-doshir@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 924531326e2dd4ceabe7240f2b55a88e7d894ec2 ]
The cache needs to be flushed to ensure that the hardware stops offloading
the flow immediately.
Fixes: 33fc42de3327 ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230330120840.52079-3-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c1cb87c2a5c29da416848451a687473f379611c ]
Since we call flow_block_cb_decref on FLOW_BLOCK_UNBIND, we also need to
call flow_block_cb_incref for a newly allocated cb.
Also fix the accidentally inverted refcount check on unbind.
Fixes: 502e84e2382d ("net: ethernet: mtk_eth_soc: add flow offloading support")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230330120840.52079-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7bcad0f0e6fbc1d613e49e0ee35c8e5f2e685bb0 ]
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257c6 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 581bce7bcb7e7f100908728e7b292e266c76895b ]
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b84 ("bnxt_en: ethtool: support PAM4 link speeds up to 200G")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 62aad36ed31abc80f35db11e187e690448a79f7d ]
Fix 57502 and 57508 NPAR description string entries. The typos
caused these devices to not match up with lspci output.
Fixes: 49c98421e6ab ("bnxt_en: Add PCI IDs for 57500 series NPAR devices.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 83714dc3db0e4a088673601bc8099b079bc1a077 ]
When the selftest command fails, driver is not reporting the failure
by updating the "test->flags" when bnxt_close_nic() fails.
Fixes: eb51365846bc ("bnxt_en: Add basic ethtool -t selftest support.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c5cff16f461a4a434a9915a7be7ac9ced861a8a4 ]
Fix invalid registers dump from ethtool -d ethX after adapter self test
by ethtool -t ethY. It causes invalid data display.
The problem was caused by overwriting i40e_reg_list[].elements
which is common for ethtool self test and dump.
Fixes: 22dd9ae8afcc ("i40e: Rework register diagnostic")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230328172659.3906413-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
