summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2024-09-04igc: Fix qbv tx latency by setting gtxoffsetFaizal Rahim1-1/+1
commit 6c3fc0b1c3d073bd6fc3bf43dbd0e64240537464 upstream. A large tx latency issue was discovered during testing when only QBV was enabled. The issue occurs because gtxoffset was not set when QBV is active, it was only set when launch time is active. The patch "igc: Correct the launchtime offset" only sets gtxoffset when the launchtime_enable field is set by the user. Enabling launchtime_enable ultimately sets the register IGC_TXQCTL_QUEUE_MODE_LAUNCHT (referred to as LaunchT in the SW user manual). Section 7.5.2.6 of the IGC i225/6 SW User Manual Rev 1.2.4 states: "The latency between transmission scheduling (launch time) and the time the packet is transmitted to the network is listed in Table 7-61." However, the patch misinterprets the phrase "launch time" in that section by assuming it specifically refers to the LaunchT register, whereas it actually denotes the generic term for when a packet is released from the internal buffer to the MAC transmit logic. This launch time, as per that section, also implicitly refers to the QBV gate open time, where a packet waits in the buffer for the QBV gate to open. Therefore, latency applies whenever QBV is in use. TSN features such as QBU and QAV reuse QBV, making the latency universal to TSN features. Discussed with i226 HW owner (Shalev, Avi) and we were in agreement that the term "launch time" used in Section 7.5.2.6 is not clear and can be easily misinterpreted. Avi will update this section to: "When TQAVCTRL.TRANSMIT_MODE = TSN, the latency between transmission scheduling and the time the packet is transmitted to the network is listed in Table 7-61." Fix this issue by using igc_tsn_is_tx_mode_in_tsn() as a condition to write to gtxoffset, aligning with the newly updated SW User Manual. Tested: 1. Enrol taprio on talker board base-time 0 cycle-time 1000000 flags 0x2 index 0 cmd S gatemask 0x1 interval1 index 0 cmd S gatemask 0x1 interval2 Note: interval1 = interval for a 64 bytes packet to go through interval2 = cycle-time - interval1 2. Take tcpdump on listener board 3. Use udp tai app on talker to send packets to listener 4. Check the timestamp on listener via wireshark Test Result: 100 Mbps: 113 ~193 ns 1000 Mbps: 52 ~ 84 ns 2500 Mbps: 95 ~ 223 ns Note that the test result is similar to the patch "igc: Correct the launchtime offset". Fixes: 790835fcc0cb ("igc: Correct the launchtime offset") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-04igc: Fix reset adapter logics when tx mode changeFaizal Rahim1-0/+7
commit 0afeaeb5dae86aceded0d5f0c3a54d27858c0c6f upstream. Following the "igc: Fix TX Hang issue when QBV Gate is close" changes, remaining issues with the reset adapter logic in igc_tsn_offload_apply() have been observed: 1. The reset adapter logics for i225 and i226 differ, although they should be the same according to the guidelines in I225/6 HW Design Section 7.5.2.1 on software initialization during tx mode changes. 2. The i225 resets adapter every time, even though tx mode doesn't change. This occurs solely based on the condition igc_is_device_id_i225() when calling schedule_work(). 3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only resets adapter for legacy->tsn tx mode transitions. 4. qbv_count introduced in the patch is actually not needed; in this context, a non-zero value of qbv_count is used to indicate if tx mode was unconditionally set to tsn in igc_tsn_enable_offload(). This could be replaced by checking the existing register IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit. This patch resolves all issues and enters schedule_work() to reset the adapter only when changing tx mode. It also removes reliance on qbv_count. qbv_count field will be removed in a future patch. Test ran: 1. Verify reset adapter behaviour in i225/6: a) Enrol a new GCL Reset adapter observed (tx mode change legacy->tsn) b) Enrol a new GCL without deleting qdisc No reset adapter observed (tx mode remain tsn->tsn) c) Delete qdisc Reset adapter observed (tx mode change tsn->legacy) 2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed" to confirm it remains resolved. Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> [ Only want the igc_tsn_is_tx_mode_in_tsn() portion of this for older stable kernels - gregkh ] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-04gtp: fix a potential NULL pointer dereferenceCong Wang1-1/+1
[ Upstream commit defd8b3c37b0f9cb3e0f60f47d3d78d459d57fda ] When sockfd_lookup() fails, gtp_encap_enable_socket() returns a NULL pointer, but its callers only check for error pointers thus miss the NULL pointer case. Fix it by returning an error pointer with the error code carried from sockfd_lookup(). (I found this bug during code inspection.) Fixes: 1e3a3abd8b28 ("gtp: make GTP sockets in gtp_newlink optional") Cc: Andreas Schultz <aschultz@tpip.net> Cc: Harald Welte <laforge@gnumonks.org> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org> Link: https://patch.msgid.link/20240825191638.146748-1-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-04bonding: implement xdo_dev_state_free and call it after deletionJianbo Liu1-0/+36
[ Upstream commit ec13009472f4a756288eb4e18e20a7845da98d10 ] Add this implementation for bonding, so hardware resources can be freed from the active slave after xfrm state is deleted. The netdev used to invoke xdo_dev_state_free callback, is saved in the xfrm state (xs->xso.real_dev), which is also the bond's active slave. To prevent it from being freed, acquire netdev reference before leaving RCU read-side critical section, and release it after callback is done. And call it when deleting all SAs from old active real interface while switching current active slave. Fixes: 9a5605505d9c ("bonding: Add struct bond_ipesc to manage SA") Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Jay Vosburgh <jv@jvosburgh.net> Link: https://patch.msgid.link/20240823031056.110999-2-jianbol@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-04wifi: iwlwifi: fw: fix wgds rev 3 exact sizeAnjaneyulu1-5/+8
[ Upstream commit 3ee22f07a35b76939c5b8d17d6af292f5fafb509 ] Check size of WGDS revision 3 is equal to 8 entries size with some header, but doesn't depend on the number of used entries. Check that used entries are between min and max but allow more to be present than are used to fix operation with some BIOSes that have such data. Fixes: 97f8a3d1610b ("iwlwifi: ACPI: support revision 3 WGDS tables") Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20240825191257.cc71dfc67ec3.Ic27ee15ac6128b275c210b6de88f2145bd83ca7b@changeid [edit commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-04net: mana: Fix race of mana_hwc_post_rx_wqe and new hwc responseHaiyang Zhang1-28/+34
commit 8af174ea863c72f25ce31cee3baad8a301c0cf0f upstream. The mana_hwc_rx_event_handler() / mana_hwc_handle_resp() calls complete(&ctx->comp_event) before posting the wqe back. It's possible that other callers, like mana_create_txq(), start the next round of mana_hwc_send_request() before the posting of wqe. And if the HW is fast enough to respond, it can hit no_wqe error on the HW channel, then the response message is lost. The mana driver may fail to create queues and open, because of waiting for the HW response and timed out. Sample dmesg: [ 528.610840] mana 39d4:00:02.0: HWC: Request timed out! [ 528.614452] mana 39d4:00:02.0: Failed to send mana message: -110, 0x0 [ 528.618326] mana 39d4:00:02.0 enP14804s2: Failed to create WQ object: -110 To fix it, move posting of rx wqe before complete(&ctx->comp_event). Cc: stable@vger.kernel.org Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-04wifi: mwifiex: duplicate static structs used in driver instancesSascha Hauer1-6/+26
commit 27ec3c57fcadb43c79ed05b2ea31bc18c72d798a upstream. mwifiex_band_2ghz and mwifiex_band_5ghz are statically allocated, but used and modified in driver instances. Duplicate them before using them in driver instances so that different driver instances do not influence each other. This was observed on a board which has one PCIe and one SDIO mwifiex adapter. It blew up in mwifiex_setup_ht_caps(). This was called with the statically allocated struct which is modified in this function. Cc: stable@vger.kernel.org Fixes: d6bffe8bb520 ("mwifiex: support for creation of AP interface") Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Acked-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240809-mwifiex-duplicate-static-structs-v1-1-6837b903b1a4@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-04wifi: wfx: repair open network AP modeAlexander Sverdlin1-1/+4
commit 6d30bb88f623526197c0e18a366e68a4254a2c83 upstream. RSN IE missing in beacon is normal in open networks. Avoid returning -EINVAL in this case. Steps to reproduce: $ cat /etc/wpa_supplicant.conf network={ ssid="testNet" mode=2 key_mgmt=NONE } $ wpa_supplicant -iwlan0 -c /etc/wpa_supplicant.conf nl80211: Beacon set failed: -22 (Invalid argument) Failed to set beacon parameters Interface initialization failed wlan0: interface state UNINITIALIZED->DISABLED wlan0: AP-DISABLED wlan0: Unable to setup interface. Failed to initialize AP interface After the change: $ wpa_supplicant -iwlan0 -c /etc/wpa_supplicant.conf Successfully initialized wpa_supplicant wlan0: interface state UNINITIALIZED->ENABLED wlan0: AP-ENABLED Cc: stable@vger.kernel.org Fixes: fe0a7776d4d1 ("wifi: wfx: fix possible NULL pointer dereference in wfx_set_mfp_ap()") Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240823131521.3309073-1-alexander.sverdlin@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-08-29ice: fix W=1 headers mismatchJesse Brandeburg2-1/+2
commit 66ceaa4c4507f2b598d37b528796dd34158d31bf upstream. make modules W=1 returns: .../ice/ice_txrx_lib.c:448: warning: Function parameter or member 'first_idx' not described in 'ice_finalize_xdp_rx' .../ice/ice_txrx.c:948: warning: Function parameter or member 'ntc' not described in 'ice_get_rx_buf' .../ice/ice_txrx.c:1038: warning: Excess function parameter 'rx_buf' description in 'ice_construct_skb' Fix these warnings by adding and deleting the deviant arguments. Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side") Fixes: d7956d81f150 ("ice: Pull out next_to_clean bump out of ice_put_rx_buf()") CC: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-08-29cxgb4: add forgotten u64 ivlan cast before shiftNikolay Kuratov1-1/+2
commit 80a1e7b83bb1834b5568a3872e64c05795d88f31 upstream. It is done everywhere in cxgb4 code, e.g. in is_filter_exact_match() There is no reason it should not be done here Found by Linux Verification Center (linuxtesting.org) with SVACE Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru> Cc: stable@vger.kernel.org Fixes: 12b276fbf6e0 ("cxgb4: add support to create hash filters") Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20240819075408.92378-1-kniv@yandex-team.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-08-29net: xilinx: axienet: Fix dangling multicast addressesSean Anderson2-12/+10
[ Upstream commit 797a68c9de0f5a5447baf4bd3bb9c10a3993435b ] If a multicast address is removed but there are still some multicast addresses, that address would remain programmed into the frame filter. Fix this by explicitly setting the enable bit for each filter. Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240822154059.1066595-3-sean.anderson@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: xilinx: axienet: Always disable promiscuous modeSean Anderson1-0/+4
[ Upstream commit 4ae738dfef2c0323752ab81786e2d298c9939321 ] If promiscuous mode is disabled when there are fewer than four multicast addresses, then it will not be reflected in the hardware. Fix this by always clearing the promiscuous mode flag even when we program multicast addresses. Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240822154059.1066595-2-sean.anderson@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29octeontx2-af: Fix CPT AF register offset calculationBharat Bhushan1-12/+11
[ Upstream commit af688a99eb1fc7ef69774665d61e6be51cea627a ] Some CPT AF registers are per LF and others are global. Translation of PF/VF local LF slot number to actual LF slot number is required only for accessing perf LF registers. CPT AF global registers access do not require any LF slot number. Also, there is no reason CPT PF/VF to know actual lf's register offset. Without this fix microcode loading will fail, VFs cannot be created and hardware is not usable. Fixes: bc35e28af789 ("octeontx2-af: replace cpt slot with lf id on reg write") Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240821070558.1020101-1-bbhushan2@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: dsa: mv88e6xxx: Fix out-of-bound accessJoseph Huang1-1/+2
[ Upstream commit 528876d867a23b5198022baf2e388052ca67c952 ] If an ATU violation was caused by a CPU Load operation, the SPID could be larger than DSA_MAX_PORTS (the size of mv88e6xxx_chip.ports[] array). Fixes: 75c05a74e745 ("net: dsa: mv88e6xxx: Fix counting of ATU violations") Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20240819235251.1331763-1-Joseph.Huang@garmin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29dpaa2-switch: Fix error checking in dpaa2_switch_seed_bp()Dan Carpenter1-3/+4
[ Upstream commit c50e7475961c36ec4d21d60af055b32f9436b431 ] The dpaa2_switch_add_bufs() function returns the number of bufs that it was able to add. It returns BUFS_PER_CMD (7) for complete success or a smaller number if there are not enough pages available. However, the error checking is looking at the total number of bufs instead of the number which were added on this iteration. Thus the error checking only works correctly for the first iteration through the loop and subsequent iterations are always counted as a success. Fix this by checking only the bufs added in the current iteration. Fixes: 0b1b71370458 ("staging: dpaa2-switch: handle Rx path on control interface") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://patch.msgid.link/eec27f30-b43f-42b6-b8ee-04a6f83423b6@stanley.mountain Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29ice: fix ICE_LAST_OFFSET formulaMaciej Fijalkowski1-1/+1
[ Upstream commit b966ad832942b5a11e002f9b5ef102b08425b84a ] For bigger PAGE_SIZE archs, ice driver works on 3k Rx buffers. Therefore, ICE_LAST_OFFSET should take into account ICE_RXBUF_3072, not ICE_RXBUF_2048. Fixes: 7237f5b0dba4 ("ice: introduce legacy Rx flag") Suggested-by: Luiz Capitulino <luizcap@redhat.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29ice: fix page reuse when PAGE_SIZE is over 8kMaciej Fijalkowski1-9/+3
[ Upstream commit 50b2143356e888777fc5bca023c39f34f404613a ] Architectures that have PAGE_SIZE >= 8192 such as arm64 should act the same as x86 currently, meaning reuse of a page should only take place when no one else is busy with it. Do two things independently of underlying PAGE_SIZE: - store the page count under ice_rx_buf::pgcnt - then act upon its value vs ice_rx_buf::pagecnt_bias when making the decision regarding page reuse Fixes: 2b245cb29421 ("ice: Implement transmit and NAPI support") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29ice: Pull out next_to_clean bump out of ice_put_rx_buf()Maciej Fijalkowski1-13/+16
[ Upstream commit d7956d81f1502d3818500cff4847f3e9ae0c6aa4 ] Plan is to move ice_put_rx_buf() to the end of ice_clean_rx_irq() so in order to keep the ability of walking through HW Rx descriptors, pull out next_to_clean handling out of ice_put_rx_buf(). Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com> Link: https://lore.kernel.org/bpf/20230131204506.219292-5-maciej.fijalkowski@intel.com Stable-dep-of: 50b2143356e8 ("ice: fix page reuse when PAGE_SIZE is over 8k") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29ice: Store page count inside ice_rx_bufMaciej Fijalkowski2-17/+12
[ Upstream commit ac0753391195011ded23696d7882428e5c419a98 ] This will allow us to avoid carrying additional auxiliary array of page counts when dealing with XDP multi buffer support. Previously combining fragmented frame to skb was not affected in the same way as XDP would be as whole frame is needed to be in place before executing XDP prog. Therefore, when going through HW Rx descriptors one-by-one, calls to ice_put_rx_buf() need to be taken *after* running XDP prog on a potentially multi buffered frame, so some additional storage of page count is needed. By adding page count to rx buf, it will make it easier to walk through processed entries at the end of rx cleaning routine and decide whether or not buffers should be recycled. While at it, bump ice_rx_buf::pagecnt_bias from u16 up to u32. It was proven many times that calculations on variables smaller than standard register size are harmful. This was also the case during experiments with embedding page count to ice_rx_buf - when this was added as u16 it had a performance impact. Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com> Link: https://lore.kernel.org/bpf/20230131204506.219292-4-maciej.fijalkowski@intel.com Stable-dep-of: 50b2143356e8 ("ice: fix page reuse when PAGE_SIZE is over 8k") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29ice: Add xdp_buff to ice_rx_ring structMaciej Fijalkowski3-16/+25
[ Upstream commit cb0473e0e9dccaa0ddafb252f2c3ef943b86bb56 ] In preparation for XDP multi-buffer support, let's store xdp_buff on Rx ring struct. This will allow us to combine fragmented frames across separate NAPI cycles in the same way as currently skb fragments are handled. This means that skb pointer on Rx ring will become redundant and will be removed. For now it is kept and layout of Rx ring struct was not inspected, some member movement will be needed later on so that will be the time to take care of it. Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com> Link: https://lore.kernel.org/bpf/20230131204506.219292-3-maciej.fijalkowski@intel.com Stable-dep-of: 50b2143356e8 ("ice: fix page reuse when PAGE_SIZE is over 8k") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29ice: Prepare legacy-rx for upcoming XDP multi-buffer supportMaciej Fijalkowski5-23/+17
[ Upstream commit c61bcebde72de7f5dc194d28f29894f0f7661ff7 ] Rx path is going to be modified in a way that fragmented frame will be gathered within xdp_buff in the first place. This approach implies that underlying buffer has to provide tailroom for skb_shared_info. This is currently the case when ring uses build_skb but not when legacy-rx knob is turned on. This case configures 2k Rx buffers and has no way to provide either headroom or tailroom - FWIW it currently has XDP_PACKET_HEADROOM which is broken and in here it is removed. 2k Rx buffers were used so driver in this setting was able to support 9k MTU as it can chain up to 5 Rx buffers. With offset configuring HW writing 2k of a data was passing the half of the page which broke the assumption of our internal page recycling tricks. Now if above got fixed and legacy-rx path would be left as is, when referring to skb_shared_info via xdp_get_shared_info_from_buff(), packet's content would be corrupted again. Hence size of Rx buffer needs to be lowered and therefore supported MTU. This operation will allow us to keep the unified data path and with 8k MTU users (if any of legacy-rx) would still be good to go. However, tendency is to drop the support for this code path at some point. Add ICE_RXBUF_1664 as vsi::rx_buf_len and ICE_MAX_FRAME_LEGACY_RX (8320) as vsi::max_frame for legacy-rx. For bigger page sizes configure 3k Rx buffers, not 2k. Since headroom support is removed, disable data_meta support on legacy-rx. When preparing XDP buff, rely on ice_rx_ring::rx_offset setting when deciding whether to support data_meta or not. Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com> Link: https://lore.kernel.org/bpf/20230131204506.219292-2-maciej.fijalkowski@intel.com Stable-dep-of: 50b2143356e8 ("ice: fix page reuse when PAGE_SIZE is over 8k") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29bonding: fix xfrm state handling when clearing active slaveNikolay Aleksandrov1-1/+1
[ Upstream commit c4c5c5d2ef40a9f67a9241dc5422eac9ffe19547 ] If the active slave is cleared manually the xfrm state is not flushed. This leads to xfrm add/del imbalance and adding the same state multiple times. For example when the device cannot handle anymore states we get: [ 1169.884811] bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA because it's filled with the same state after multiple active slave clearings. This change also has a few nice side effects: user-space gets a notification for the change, the old device gets its mac address and promisc/mcast adjusted properly. Fixes: 18cb261afd7b ("bonding: support hardware encryption offload to slaves") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29bonding: fix xfrm real_dev null pointer dereferenceNikolay Aleksandrov1-1/+0
[ Upstream commit f8cde9805981c50d0c029063dc7d82821806fc44 ] We shouldn't set real_dev to NULL because packets can be in transit and xfrm might call xdo_dev_offload_ok() in parallel. All callbacks assume real_dev is set. Example trace: kernel: BUG: unable to handle page fault for address: 0000000000001030 kernel: bond0: (slave eni0np1): making interface the new active one kernel: #PF: supervisor write access in kernel mode kernel: #PF: error_code(0x0002) - not-present page kernel: PGD 0 P4D 0 kernel: Oops: 0002 [#1] PREEMPT SMP kernel: CPU: 4 PID: 2237 Comm: ping Not tainted 6.7.7+ #12 kernel: Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 kernel: RIP: 0010:nsim_ipsec_offload_ok+0xc/0x20 [netdevsim] kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: Code: e0 0f 0b 48 83 7f 38 00 74 de 0f 0b 48 8b 47 08 48 8b 37 48 8b 78 40 e9 b2 e5 9a d7 66 90 0f 1f 44 00 00 48 8b 86 80 02 00 00 <83> 80 30 10 00 00 01 b8 01 00 00 00 c3 0f 1f 80 00 00 00 00 0f 1f kernel: bond0: (slave eni0np1): making interface the new active one kernel: RSP: 0018:ffffabde81553b98 EFLAGS: 00010246 kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: kernel: RAX: 0000000000000000 RBX: ffff9eb404e74900 RCX: ffff9eb403d97c60 kernel: RDX: ffffffffc090de10 RSI: ffff9eb404e74900 RDI: ffff9eb3c5de9e00 kernel: RBP: ffff9eb3c0a42000 R08: 0000000000000010 R09: 0000000000000014 kernel: R10: 7974203030303030 R11: 3030303030303030 R12: 0000000000000000 kernel: R13: ffff9eb3c5de9e00 R14: ffffabde81553cc8 R15: ffff9eb404c53000 kernel: FS: 00007f2a77a3ad00(0000) GS:ffff9eb43bd00000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 0000000000001030 CR3: 00000001122ab000 CR4: 0000000000350ef0 kernel: bond0: (slave eni0np1): making interface the new active one kernel: Call Trace: kernel: <TASK> kernel: ? __die+0x1f/0x60 kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: ? page_fault_oops+0x142/0x4c0 kernel: ? do_user_addr_fault+0x65/0x670 kernel: ? kvm_read_and_reset_apf_flags+0x3b/0x50 kernel: bond0: (slave eni0np1): making interface the new active one kernel: ? exc_page_fault+0x7b/0x180 kernel: ? asm_exc_page_fault+0x22/0x30 kernel: ? nsim_bpf_uninit+0x50/0x50 [netdevsim] kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: ? nsim_ipsec_offload_ok+0xc/0x20 [netdevsim] kernel: bond0: (slave eni0np1): making interface the new active one kernel: bond_ipsec_offload_ok+0x7b/0x90 [bonding] kernel: xfrm_output+0x61/0x3b0 kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA kernel: ip_push_pending_frames+0x56/0x80 Fixes: 18cb261afd7b ("bonding: support hardware encryption offload to slaves") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29bonding: fix null pointer deref in bond_ipsec_offload_okNikolay Aleksandrov1-0/+2
[ Upstream commit 95c90e4ad89d493a7a14fa200082e466e2548f9d ] We must check if there is an active slave before dereferencing the pointer. Fixes: 18cb261afd7b ("bonding: support hardware encryption offload to slaves") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29bonding: fix bond_ipsec_offload_ok return typeNikolay Aleksandrov1-12/+6
[ Upstream commit fc59b9a5f7201b9f7272944596113a82cc7773d5 ] Fix the return type which should be bool. Fixes: 955b785ec6b3 ("bonding: fix suspicious RCU usage in bond_ipsec_offload_ok()") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: mscc: ocelot: serialize access to the injection/extraction groupsVladimir Oltean3-0/+67
[ Upstream commit c5e12ac3beb0dd3a718296b2d8af5528e9ab728e ] As explained by Horatiu Vultur in commit 603ead96582d ("net: sparx5: Add spinlock for frame transmission from CPU") which is for a similar hardware design, multiple CPUs can simultaneously perform injection or extraction. There are only 2 register groups for injection and 2 for extraction, and the driver only uses one of each. So we'd better serialize access using spin locks, otherwise frame corruption is possible. Note that unlike in sparx5, FDMA in ocelot does not have this issue because struct ocelot_fdma_tx_ring already contains an xmit_lock. I guess this is mostly a problem for NXP LS1028A, as that is dual core. I don't think VSC7514 is. So I'm blaming the commit where LS1028A (aka the felix DSA driver) started using register-based packet injection and extraction. Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: mscc: ocelot: fix QoS class for injected packets with "ocelot-8021q"Vladimir Oltean2-2/+9
[ Upstream commit e1b9e80236c540fa85d76e2d510d1b38e1968c5d ] There are 2 distinct code paths (listed below) in the source code which set up an injection header for Ocelot(-like) switches. Code path (2) lacks the QoS class and source port being set correctly. Especially the improper QoS classification is a problem for the "ocelot-8021q" alternative DSA tagging protocol, because we support tc-taprio and each packet needs to be scheduled precisely through its time slot. This includes PTP, which is normally assigned to a traffic class other than 0, but would be sent through TC 0 nonetheless. The code paths are: (1) ocelot_xmit_common() from net/dsa/tag_ocelot.c - called only by the standard "ocelot" DSA tagging protocol which uses NPI-based injection - sets up bit fields in the tag manually to account for a small difference (destination port offset) between Ocelot and Seville. Namely, ocelot_ifh_set_dest() is omitted out of ocelot_xmit_common(), because there's also seville_ifh_set_dest(). (2) ocelot_ifh_set_basic(), called by: - ocelot_fdma_prepare_skb() for FDMA transmission of the ocelot switchdev driver - ocelot_port_xmit() -> ocelot_port_inject_frame() for register-based transmission of the ocelot switchdev driver - felix_port_deferred_xmit() -> ocelot_port_inject_frame() for the DSA tagger ocelot-8021q when it must transmit PTP frames (also through register-based injection). sets the bit fields according to its own logic. The problem is that (2) doesn't call ocelot_ifh_set_qos_class(). Copying that logic from ocelot_xmit_common() fixes that. Unfortunately, although desirable, it is not easily possible to de-duplicate code paths (1) and (2), and make net/dsa/tag_ocelot.c directly call ocelot_ifh_set_basic()), because of the ocelot/seville difference. This is the "minimal" fix with some logic duplicated (but at least more consolidated). Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: mscc: ocelot: use ocelot_xmit_get_vlan_info() also for FDMA and ↵Vladimir Oltean2-7/+24
register injection [ Upstream commit 67c3ca2c5cfe6a50772514e3349b5e7b3b0fac03 ] Problem description ------------------- On an NXP LS1028A (felix DSA driver) with the following configuration: - ocelot-8021q tagging protocol - VLAN-aware bridge (with STP) spanning at least swp0 and swp1 - 8021q VLAN upper interfaces on swp0 and swp1: swp0.700, swp1.700 - ptp4l on swp0.700 and swp1.700 we see that the ptp4l instances do not see each other's traffic, and they all go to the grand master state due to the ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES condition. Jumping to the conclusion for the impatient ------------------------------------------- There is a zero-day bug in the ocelot switchdev driver in the way it handles VLAN-tagged packet injection. The correct logic already exists in the source code, in function ocelot_xmit_get_vlan_info() added by commit 5ca721c54d86 ("net: dsa: tag_ocelot: set the classified VLAN during xmit"). But it is used only for normal NPI-based injection with the DSA "ocelot" tagging protocol. The other injection code paths (register-based and FDMA-based) roll their own wrong logic. This affects and was noticed on the DSA "ocelot-8021q" protocol because it uses register-based injection. By moving ocelot_xmit_get_vlan_info() to a place that's common for both the DSA tagger and the ocelot switch library, it can also be called from ocelot_port_inject_frame() in ocelot.c. We need to touch the lines with ocelot_ifh_port_set()'s prototype anyway, so let's rename it to something clearer regarding what it does, and add a kernel-doc. ocelot_ifh_set_basic() should do. Investigation notes ------------------- Debugging reveals that PTP event (aka those carrying timestamps, like Sync) frames injected into swp0.700 (but also swp1.700) hit the wire with two VLAN tags: 00000000: 01 1b 19 00 00 00 00 01 02 03 04 05 81 00 02 bc ~~~~~~~~~~~ 00000010: 81 00 02 bc 88 f7 00 12 00 2c 00 00 02 00 00 00 ~~~~~~~~~~~ 00000020: 00 00 00 00 00 00 00 00 00 00 00 01 02 ff fe 03 00000030: 04 05 00 01 00 04 00 00 00 00 00 00 00 00 00 00 00000040: 00 00 The second (unexpected) VLAN tag makes felix_check_xtr_pkt() -> ptp_classify_raw() fail to see these as PTP packets at the link partner's receiving end, and return PTP_CLASS_NONE (because the BPF classifier is not written to expect 2 VLAN tags). The reason why packets have 2 VLAN tags is because the transmission code treats VLAN incorrectly. Neither ocelot switchdev, nor felix DSA, declare the NETIF_F_HW_VLAN_CTAG_TX feature. Therefore, at xmit time, all VLANs should be in the skb head, and none should be in the hwaccel area. This is done by: static struct sk_buff *validate_xmit_vlan(struct sk_buff *skb, netdev_features_t features) { if (skb_vlan_tag_present(skb) && !vlan_hw_offload_capable(features, skb->vlan_proto)) skb = __vlan_hwaccel_push_inside(skb); return skb; } But ocelot_port_inject_frame() handles things incorrectly: ocelot_ifh_port_set(ifh, port, rew_op, skb_vlan_tag_get(skb)); void ocelot_ifh_port_set(struct sk_buff *skb, void *ifh, int port, u32 rew_op) { (...) if (vlan_tag) ocelot_ifh_set_vlan_tci(ifh, vlan_tag); (...) } The way __vlan_hwaccel_push_inside() pushes the tag inside the skb head is by calling: static inline void __vlan_hwaccel_clear_tag(struct sk_buff *skb) { skb->vlan_present = 0; } which does _not_ zero out skb->vlan_tci as seen by skb_vlan_tag_get(). This means that ocelot, when it calls skb_vlan_tag_get(), sees (and uses) a residual skb->vlan_tci, while the same VLAN tag is _already_ in the skb head. The trivial fix for double VLAN headers is to replace the content of ocelot_ifh_port_set() with: if (skb_vlan_tag_present(skb)) ocelot_ifh_set_vlan_tci(ifh, skb_vlan_tag_get(skb)); but this would not be correct either, because, as mentioned, vlan_hw_offload_capable() is false for us, so we'd be inserting dead code and we'd always transmit packets with VID=0 in the injection frame header. I can't actually test the ocelot switchdev driver and rely exclusively on code inspection, but I don't think traffic from 8021q uppers has ever been injected properly, and not double-tagged. Thus I'm blaming the introduction of VLAN fields in the injection header - early driver code. As hinted at in the early conclusion, what we _want_ to happen for VLAN transmission was already described once in commit 5ca721c54d86 ("net: dsa: tag_ocelot: set the classified VLAN during xmit"). ocelot_xmit_get_vlan_info() intends to ensure that if the port through which we're transmitting is under a VLAN-aware bridge, the outer VLAN tag from the skb head is stripped from there and inserted into the injection frame header (so that the packet is processed in hardware through that actual VLAN). And in all other cases, the packet is sent with VID=0 in the injection frame header, since the port is VLAN-unaware and has logic to strip this VID on egress (making it invisible to the wire). Fixes: 08d02364b12f ("net: mscc: fix the injection header") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: mana: Fix doorbell out of order violation and avoid unnecessary ↵Long Li2-9/+16
doorbell rings [ Upstream commit 58a63729c957621f1990c3494c702711188ca347 ] After napi_complete_done() is called when NAPI is polling in the current process context, another NAPI may be scheduled and start running in softirq on another CPU and may ring the doorbell before the current CPU does. When combined with unnecessary rings when there is no need to arm the CQ, it triggers error paths in the hardware. This patch fixes this by calling napi_complete_done() after doorbell rings. It limits the number of unnecessary rings when there is no need to arm. MANA hardware specifies that there must be one doorbell ring every 8 CQ wraparounds. This driver guarantees one doorbell ring as soon as the number of consumed CQEs exceeds 4 CQ wraparounds. In practical workloads, the 4 CQ wraparounds proves to be big enough that it rarely exceeds this limit before all the napi weight is consumed. To implement this, add a per-CQ counter cq->work_done_since_doorbell, and make sure the CQ is armed as soon as passing 4 wraparounds of the CQ. Cc: stable@vger.kernel.org Fixes: e1b5683ff62e ("net: mana: Move NAPI from EQ to CQ") Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Long Li <longli@microsoft.com> Link: https://patch.msgid.link/1723219138-29887-1-git-send-email-longli@linuxonhyperv.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29gtp: pull network headers in gtp_dev_xmit()Eric Dumazet1-0/+3
commit 3a3be7ff9224f424e485287b54be00d2c6bd9c40 upstream. syzbot/KMSAN reported use of uninit-value in get_dev_xmit() [1] We must make sure the IPv4 or Ipv6 header is pulled in skb->head before accessing fields in them. Use pskb_inet_may_pull() to fix this issue. [1] BUG: KMSAN: uninit-value in ipv6_pdp_find drivers/net/gtp.c:220 [inline] BUG: KMSAN: uninit-value in gtp_build_skb_ip6 drivers/net/gtp.c:1229 [inline] BUG: KMSAN: uninit-value in gtp_dev_xmit+0x1424/0x2540 drivers/net/gtp.c:1281 ipv6_pdp_find drivers/net/gtp.c:220 [inline] gtp_build_skb_ip6 drivers/net/gtp.c:1229 [inline] gtp_dev_xmit+0x1424/0x2540 drivers/net/gtp.c:1281 __netdev_start_xmit include/linux/netdevice.h:4913 [inline] netdev_start_xmit include/linux/netdevice.h:4922 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3596 __dev_queue_xmit+0x358c/0x5610 net/core/dev.c:4423 dev_queue_xmit include/linux/netdevice.h:3105 [inline] packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3145 [inline] packet_sendmsg+0x90e3/0xa3a0 net/packet/af_packet.c:3177 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2204 __do_sys_sendto net/socket.c:2216 [inline] __se_sys_sendto net/socket.c:2212 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2212 x64_sys_call+0x3799/0x3c10 arch/x86/include/generated/asm/syscalls_64.h:45 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:3994 [inline] slab_alloc_node mm/slub.c:4037 [inline] kmem_cache_alloc_node_noprof+0x6bf/0xb80 mm/slub.c:4080 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:583 __alloc_skb+0x363/0x7b0 net/core/skbuff.c:674 alloc_skb include/linux/skbuff.h:1320 [inline] alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6526 sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2815 packet_alloc_skb net/packet/af_packet.c:2994 [inline] packet_snd net/packet/af_packet.c:3088 [inline] packet_sendmsg+0x749c/0xa3a0 net/packet/af_packet.c:3177 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2204 __do_sys_sendto net/socket.c:2216 [inline] __se_sys_sendto net/socket.c:2212 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2212 x64_sys_call+0x3799/0x3c10 arch/x86/include/generated/asm/syscalls_64.h:45 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f CPU: 0 UID: 0 PID: 7115 Comm: syz.1.515 Not tainted 6.11.0-rc1-syzkaller-00043-g94ede2a3e913 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/27/2024 Fixes: 999cb275c807 ("gtp: add IPv6 support") Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Harald Welte <laforge@gnumonks.org> Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org> Link: https://patch.msgid.link/20240808132455.3413916-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-08-29net: hns3: add checking for vf id of mailboxJian Shen1-3/+4
[ Upstream commit 4e2969a0d6a7549bc0bc1ebc990588b622c4443d ] Add checking for vf id of mailbox, in order to avoid array out-of-bounds risk. Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net/sun3_82586: Avoid reading past buffer in debug outputKees Cook1-1/+1
[ Upstream commit 4bea747f3fbec33c16d369b2f51e55981d7c78d0 ] Since NUM_XMIT_BUFFS is always 1, building m68k with sun3_defconfig and -Warraybounds, this build warning is visible[1]: drivers/net/ethernet/i825xx/sun3_82586.c: In function 'sun3_82586_timeout': drivers/net/ethernet/i825xx/sun3_82586.c:990:122: warning: array subscript 1 is above array bounds of 'volatile struct transmit_cmd_struct *[1]' [-Warray-bounds=] 990 | printk("%s: command-stats: %04x %04x\n",dev->name,swab16(p->xmit_cmds[0]->cmd_status),swab16(p->xmit_cmds[1]->cmd_status)); | ~~~~~~~~~~~~^~~ ... drivers/net/ethernet/i825xx/sun3_82586.c:156:46: note: while referencing 'xmit_cmds' 156 | volatile struct transmit_cmd_struct *xmit_cmds[NUM_XMIT_BUFFS]; Avoid accessing index 1 since it doesn't exist. Link: https://github.com/KSPP/linux/issues/325 [1] Cc: Sam Creasey <sammy@sammy.net> Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Simon Horman <horms@kernel.org> # build-tested Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/20240206161651.work.876-kees@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29wifi: iwlwifi: fw: Fix debugfs command sendingMukesh Sisodiya1-1/+5
[ Upstream commit 048449fc666d736a1a17d950fde0b5c5c8fd10cc ] During debugfs command handling transport function is used directly, this bypasses the locking used by runtime operation function and leads to a kernel warning when two commands are sent in parallel. Fix it by using runtime operations function when sending debugfs command. Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com> Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/20231004123422.4f80ac90658a.Ia1dfa1195c919f3002fe08db3eefbd2bfa921bbf@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29wifi: iwlwifi: abort scan when rfkill on but device enabledMiri Korenblit1-1/+1
[ Upstream commit 3c6a0b1f0add72e7f522bc9145222b86d0a7712a ] In RFKILL we first set the RFKILL bit, then we abort scan (if one exists) by waiting for the notification from FW and notifying mac80211. And then we stop the device. But in case we have a scan ongoing in the period of time between rfkill on and before the device is stopped - we will not wait for the FW notification because of the iwl_mvm_is_radio_killed() condition, and then the scan_status and uid_status are misconfigured, (scan_status is cleared but uid_status not) and when the notification suddenly arrives (before stopping the device) we will get into the assert about scan_status and uid_status mismatch. Fix this by waiting for FW notif when rfkill is on but the device isn't disabled yet. Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/20231004123422.c43b69aa2c77.Icc7b5efb47974d6f499156ff7510b786e177993b@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29wifi: cw1200: Avoid processing an invalid TIM IEJeff Johnson1-1/+1
[ Upstream commit b7bcea9c27b3d87b54075735c870500123582145 ] While converting struct ieee80211_tim_ie::virtual_map to be a flexible array it was observed that the TIM IE processing in cw1200_rx_cb() could potentially process a malformed IE in a manner that could result in a buffer over-read. Add logic to verify that the TIM IE length is large enough to hold a valid TIM payload before processing it. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230831-ieee80211_tim_ie-v3-1-e10ff584ab5d@quicinc.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: hns3: fix a deadlock problem when config TC during resettingJie Wang1-0/+3
[ Upstream commit be5e816d00a506719e9dbb1a9c861c5ced30a109 ] When config TC during the reset process, may cause a deadlock, the flow is as below: pf reset start │ ▼ ...... setup tc │ │ ▼ ▼ DOWN: napi_disable() napi_disable()(skip) │ │ │ ▼ ▼ ...... ...... │ │ ▼ │ napi_enable() │ ▼ UINIT: netif_napi_del() │ ▼ ...... │ ▼ INIT: netif_napi_add() │ ▼ ...... global reset start │ │ ▼ ▼ UP: napi_enable()(skip) ...... │ │ ▼ ▼ ...... napi_disable() In reset process, the driver will DOWN the port and then UINIT, in this case, the setup tc process will UP the port before UINIT, so cause the problem. Adds a DOWN process in UINIT to fix it. Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: hns3: use the user's cfg after resetPeiyang Wang2-6/+21
[ Upstream commit 30545e17eac1f50c5ef49644daf6af205100a965 ] Consider the followed case that the user change speed and reset the net interface. Before the hw change speed successfully, the driver get old old speed from hw by timer task. After reset, the previous speed is config to hw. As a result, the new speed is configed successfully but lost after PF reset. The followed pictured shows more dirrectly. +------+ +----+ +----+ | USER | | PF | | HW | +---+--+ +-+--+ +-+--+ | ethtool -s 100G | | +------------------>| set speed 100G | | +--------------------->| | | set successfully | | |<---------------------+---+ | |query cfg (timer task)| | | +--------------------->| | handle speed | | return 200G | | changing event | ethtool --reset |<---------------------+ | (100G) +------------------>| cfg previous speed |<--+ | | after reset (200G) | | +--------------------->| | | +---+ | |query cfg (timer task)| | | +--------------------->| | handle speed | | return 100G | | changing event | |<---------------------+ | (200G) | | |<--+ | |query cfg (timer task)| | +--------------------->| | | return 200G | | |<---------------------+ | | | v v v This patch save new speed if hw change speed successfully, which will be used after reset successfully. Fixes: 2d03eacc0b7e ("net: hns3: Only update mac configuation when necessary") Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: hns3: fix wrong use of semaphore upJie Wang2-4/+4
[ Upstream commit 8445d9d3c03101859663d34fda747f6a50947556 ] Currently, if hns3 PF or VF FLR reset failed after five times retry, the reset done process will directly release the semaphore which has already released in hclge_reset_prepare_general. This will cause down operation fail. So this patch fixes it by adding reset state judgement. The up operation is only called after successful PF FLR reset. Fixes: 8627bdedc435 ("net: hns3: refactor the precedure of PF FLR") Fixes: f28368bb4542 ("net: hns3: refactor the procedure of VF FLR") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29mlxbf_gige: disable RX filters until RX path initializedDavid Thompson4-6/+64
[ Upstream commit df934abb185c71c9f2fa07a5013672d0cbd36560 ] A recent change to the driver exposed a bug where the MAC RX filters (unicast MAC, broadcast MAC, and multicast MAC) are configured and enabled before the RX path is fully initialized. The result of this bug is that after the PHY is started packets that match these MAC RX filters start to flow into the RX FIFO. And then, after rx_init() is completed, these packets will go into the driver RX ring as well. If enough packets are received to fill the RX ring (default size is 128 packets) before the call to request_irq() completes, the driver RX function becomes stuck. This bug is intermittent but is most likely to be seen where the oob_net0 interface is connected to a busy network with lots of broadcast and multicast traffic. All the MAC RX filters must be disabled until the RX path is ready, i.e. all initialization is done and all the IRQs are installed. Fixes: f7442a634ac0 ("mlxbf_gige: call request_irq() after NAPI initialized") Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com> Signed-off-by: David Thompson <davthompson@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240809163612.12852-1-davthompson@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29mlxbf_gige: Remove two unused function declarationsYue Haibing1-3/+0
[ Upstream commit 98261be155f8de38f11b6542d4a8935e5532687b ] Commit f92e1869d74e ("Add Mellanox BlueField Gigabit Ethernet driver") declared but never implemented these. Signed-off-by: Yue Haibing <yuehaibing@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com> Link: https://lore.kernel.org/r/20230808145249.41596-1-yuehaibing@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Stable-dep-of: df934abb185c ("mlxbf_gige: disable RX filters until RX path initialized") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: dsa: vsc73xx: check busy flag in MDIO operationsPawel Dembicki1-1/+36
[ Upstream commit fa63c6434b6f6aaf9d8d599dc899bc0a074cc0ad ] The VSC73xx has a busy flag used during MDIO operations. It is raised when MDIO read/write operations are in progress. Without it, PHYs are misconfigured and bus operations do not work as expected. Fixes: 05bd97fc559d ("net: dsa: Add Vitesse VSC73xx DSA router driver") Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: dsa: vsc73xx: use read_poll_timeout instead delay loopPawel Dembicki1-14/+16
[ Upstream commit eb7e33d01db3aec128590391b2397384bab406b6 ] Switch the delay loop during the Arbiter empty check from vsc73xx_adjust_link() to use read_poll_timeout(). Functionally, one msleep() call is eliminated at the end of the loop in the timeout case. As Russell King suggested: "This [change] avoids the issue that on the last iteration, the code reads the register, tests it, finds the condition that's being waiting for is false, _then_ waits and end up printing the error message - that last wait is rather useless, and as the arbiter state isn't checked after waiting, it could be that we had success during the last wait." Suggested-by: Russell King <linux@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Link: https://lore.kernel.org/r/20240417205048.3542839-2-paweldembicki@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Stable-dep-of: fa63c6434b6f ("net: dsa: vsc73xx: check busy flag in MDIO operations") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: dsa: vsc73xx: pass value in phy_write operationPawel Dembicki1-1/+1
[ Upstream commit 5b9eebc2c7a5f0cc7950d918c1e8a4ad4bed5010 ] In the 'vsc73xx_phy_write' function, the register value is missing, and the phy write operation always sends zeros. This commit passes the value variable into the proper register. Fixes: 05bd97fc559d ("net: dsa: Add Vitesse VSC73xx DSA router driver") Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net: axienet: Fix register defines comment descriptionRadhey Shyam Pandey1-8/+8
[ Upstream commit 9ff2f816e2aa65ca9a1cdf0954842f8173c0f48d ] In axiethernet header fix register defines comment description to be inline with IP documentation. It updates MAC configuration register, MDIO configuration register and frame filter control description. Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net/mlx5e: Correctly report errors for ethtool rx flowsCosmin Ratiu1-1/+1
[ Upstream commit cbc796be1779c4dbc9a482c7233995e2a8b6bfb3 ] Previously, an ethtool rx flow with no attrs would not be added to the NIC as it has no rules to configure the hw with, but it would be reported as successful to the caller (return code 0). This is confusing for the user as ethtool then reports "Added rule $num", but no rule was actually added. This change corrects that by instead reporting these wrong rules as -EINVAL. Fixes: b29c61dac3a2 ("net/mlx5e: Ethtool steering flow validation refactoring") Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com> Reviewed-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-5-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29net/mlx5e: Take state lock during tx timeout reporterDragos Tatulea1-0/+2
[ Upstream commit e6b5afd30b99b43682a7764e1a74a42fe4d5f4b3 ] mlx5e_safe_reopen_channels() requires the state lock taken. The referenced changed in the Fixes tag removed the lock to fix another issue. This patch adds it back but at a later point (when calling mlx5e_safe_reopen_channels()) to avoid the deadlock referenced in the Fixes tag. Fixes: eab0da38912e ("net/mlx5e: Fix possible deadlock on mlx5e_tx_timeout_work") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Link: https://lore.kernel.org/all/ZplpKq8FKi3vwfxv@gmail.com/T/ Reviewed-by: Breno Leitao <leitao@debian.org> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-4-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29igc: Fix packet still tx after gate close by reducing i226 MAC retry bufferFaizal Rahim2-0/+40
[ Upstream commit e037a26ead187901f83cad9c503ccece5ff6817a ] Testing uncovered that even when the taprio gate is closed, some packets still transmit. According to i225/6 hardware errata [1], traffic might overflow the planned QBV window. This happens because MAC maintains an internal buffer, primarily for supporting half duplex retries. Therefore, even when the gate closes, residual MAC data in the buffer may still transmit. To mitigate this for i226, reduce the MAC's internal buffer from 192 bytes to the recommended 88 bytes by modifying the RETX_CTL register value. This follows guidelines from: [1] Ethernet Controller I225/I22 Spec Update Rev 2.1 Errata Item 9: TSN: Packet Transmission Might Cross Qbv Window [2] I225/6 SW User Manual Rev 1.2.4: Section 8.11.5 Retry Buffer Control Note that the RETX_CTL register can't be used in TSN mode because half duplex feature cannot coexist with TSN. Test Steps: 1. Send taprio cmd to board A: tc qdisc replace dev enp1s0 parent root handle 100 taprio \ num_tc 4 \ map 3 2 1 0 3 3 3 3 3 3 3 3 3 3 3 3 \ queues 1@0 1@1 1@2 1@3 \ base-time 0 \ sched-entry S 0x07 500000 \ sched-entry S 0x0f 500000 \ flags 0x2 \ txtime-delay 0 Note that for TC3, gate should open for 500us and close for another 500us. 3. Take tcpdump log on Board B. 4. Send udp packets via UDP tai app from Board A to Board B. 5. Analyze tcpdump log via wireshark log on Board B. Ensure that the total time from the first to the last packet received during one cycle for TC3 does not exceed 500us. Fixes: 43546211738e ("igc: Add new device ID's") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29igc: Correct the launchtime offsetMuhammad Husaini Zulkifli5-0/+48
[ Upstream commit 790835fcc0cb9992349ae3c9010dbc7321aaa24d ] The launchtime offset should be corrected according to sections 7.5.2.6 Transmit Scheduling Latency of the Intel Ethernet I225/I226 Software User Manual. Software can compensate the latency between the transmission scheduling and the time that packet is transmitted to the network by setting this GTxOffset register. Without setting this register, there may be a significant delay between the packet scheduling and the network point. This patch helps to reduce the latency for each of the link speed. Before: 10Mbps : 11000 - 13800 nanosecond 100Mbps : 1300 - 1700 nanosecond 1000Mbps : 190 - 600 nanosecond 2500Mbps : 1400 - 1700 nanosecond After: 10Mbps : less than 750 nanosecond 100Mbps : less than 192 nanosecond 1000Mbps : less than 128 nanosecond 2500Mbps : less than 128 nanosecond Test Setup: Talker : Use l2_tai.c to generate the launchtime into packet payload. Listener: Use timedump.c to compute the delta between packet arrival and LaunchTime packet payload. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Acked-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Stable-dep-of: e037a26ead18 ("igc: Fix packet still tx after gate close by reducing i226 MAC retry buffer") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29wifi: mac80211: fix receiving A-MSDU frames on mesh interfacesFelix Fietkau1-1/+1
[ Upstream commit 986e43b19ae9176093da35e0a844e65c8bf9ede7 ] The current mac80211 mesh A-MSDU receive path fails to parse A-MSDU packets on mesh interfaces, because it assumes that the Mesh Control field is always directly after the 802.11 header. 802.11-2020 9.3.2.2.2 Figure 9-70 shows that the Mesh Control field is actually part of the A-MSDU subframe header. This makes more sense, since it allows packets for multiple different destinations to be included in the same A-MSDU, as long as RA and TID are still the same. Another issue is the fact that the A-MSDU subframe length field was apparently accidentally defined as little-endian in the standard. In order to fix this, the mesh forwarding path needs happen at a different point in the receive path. ieee80211_data_to_8023_exthdr is changed to ignore the mesh control field and leave it in after the ethernet header. This also affects the source/dest MAC address fields, which now in the case of mesh point to the mesh SA/DA. ieee80211_amsdu_to_8023s is changed to deal with the endian difference and to add the Mesh Control length to the subframe length, since it's not covered by the MSDU length field. With these changes, the mac80211 will get the same packet structure for converted regular data packets and unpacked A-MSDU subframes. The mesh forwarding checks are now only performed after the A-MSDU decap. For locally received packets, the Mesh Control header is stripped away. For forwarded packets, a new 802.11 header gets added. Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20230213100855.34315-4-nbd@nbd.name [fix fortify build error] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Stable-dep-of: 9ad797485692 ("wifi: cfg80211: check A-MSDU format more carefully") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-29pppoe: Fix memory leak in pppoe_sendmsg()Gavrilov Ilia1-14/+9
[ Upstream commit dc34ebd5c018b0edf47f39d11083ad8312733034 ] syzbot reports a memory leak in pppoe_sendmsg [1]. The problem is in the pppoe_recvmsg() function that handles errors in the wrong order. For the skb_recv_datagram() function, check the pointer to skb for NULL first, and then check the 'error' variable, because the skb_recv_datagram() function can set 'error' to -EAGAIN in a loop but return a correct pointer to socket buffer after a number of attempts, though 'error' remains set to -EAGAIN. skb_recv_datagram __skb_recv_datagram // Loop. if (err == -EAGAIN) then // go to the next loop iteration __skb_try_recv_datagram // if (skb != NULL) then return 'skb' // else if a signal is received then // return -EAGAIN Found by InfoTeCS on behalf of Linux Verification Center (linuxtesting.org) with Syzkaller. Link: https://syzkaller.appspot.com/bug?extid=6bdfd184eac7709e5cc9 [1] Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+6bdfd184eac7709e5cc9@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=6bdfd184eac7709e5cc9 Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Guillaume Nault <gnault@redhat.com> Link: https://lore.kernel.org/r/20240214085814.3894917-1-Ilia.Gavrilov@infotecs.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-03-15 08:02:05 +0300