| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 3a0a88fcbaf9e027ecca3fe8775be9700b4d6460 ]
This patch updates the workaround for a problem similar to erratum
DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
In the bad case, the driver reads a too large head index. As the FIFO
is implemented as a ring buffer, this results in re-handling old CAN
transmit complete events.
Every transmit complete event contains with a sequence number that
equals to the sequence number of the corresponding TX request. This
way old TX complete events can be detected.
If the original driver detects a non matching sequence number, it
prints an info message and tries again later. As wrong sequence
numbers can be explained by the erratum DS80000789E 6, demote the info
message to debug level, streamline the code and update the comments.
Keep the behavior: If an old CAN TX complete event is detected, abort
the iteration and mark the number of valid CAN TX complete events as
processed in the chip by incrementing the FIFO's tail index.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b8e0ddd36ce9536ad7478dd27df06c9ae92370ba ]
This is a preparatory patch to work around a problem similar to
erratum DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
When handling the TEF interrupt, the driver reads the FIFO header
index from the TEF FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN transmit complete events that were already processed to be
re-processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_tef_ring_update() with mcp251xfd_get_tef_len().
The mcp251xfd_handle_tefif() function reads the CAN transmit complete
events from the chip, iterates over them and pushes them into the
network stack. The original driver already contains code to detect old
CAN transmit complete events, that will be updated in the next patch.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fba8334721e266f92079632598e46e5f89082f30 ]
When all the strides in a WQE have been consumed, the WQE is unlinked
from the WQ linked list (mlx5_wq_ll_pop()). For SHAMPO, it is possible
to receive CQEs with 0 consumed strides for the same WQE even after the
WQE is fully consumed and unlinked. This triggers an additional unlink
for the same wqe which corrupts the linked list.
Fix this scenario by accepting 0 sized consumed strides without
unlinking the WQE again.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240603212219.1037656-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8fee6d5ad5fa18c270eedb2a2cdf58dbadefb94b ]
PPS was not stopped in `fec_ptp_stop()`, called when
the adapter was removed. Consequentially, you couldn't
safely reload the driver with the PPS signal on.
Fixes: 32cba57ba74b ("net: fec: introduce fec_ptp_stop and use in probe fail path")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/netdev/CAOMZO5BzcZR8PwKKwBssQq_wAGzVgf1ffwe_nhpQJjviTdxy-w@mail.gmail.com/T/#m01dcb810bfc451a492140f6797ca77443d0cb79f
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20240807080956.2556602-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3862093ee93fcfbdadcb7957f5f8974fffa806a ]
bcm_sf2_mdio_register() calls of_phy_find_device() and then
phy_device_remove() in a loop to remove existing PHY devices.
of_phy_find_device() eventually calls bus_find_device(), which calls
get_device() on the returned struct device * to increment the refcount.
The current implementation does not decrement the refcount, which causes
memory leak.
This commit adds the missing phy_device_free() call to decrement the
refcount via put_device() to balance the refcount.
Fixes: 771089c2a485 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806011327.3817861-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7ab107544b777c3bd7feb9fe447367d8edd5b202 ]
Free the unused skb when not ip packets arrive.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d516b187a9cc2e842030dd005be2735db3e8f395 upstream.
The skb isn't consumed in case of NETDEV_TX_BUSY, therefore don't
increment the tx_dropped counter.
Fixes: 188f4af04618 ("r8169: use NETDEV_TX_{BUSY/OK}")
Cc: stable@vger.kernel.org
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/bbba9c48-8bac-4932-9aa1-d2ed63bc9433@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08f3a5c38087d1569e982a121aad1e6acbf145ce upstream.
It could lead to error happen because the variable res is not updated if
the call to sr_share_read_word returns an error. In this particular case
error code was returned and res stayed uninitialized. Same issue also
applies to sr_read_reg.
This can be avoided by checking the return value of sr_share_read_word
and sr_read_reg, and propagating the error if the read operation failed.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: c9b37458e956 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3f8e82a020a5c22f9b791f4ac499b8e18007fbda ]
Since the documentation for mlx5_toggle_port_link states that it should
only be used after setting the port register, we add a check for the
return value from mlx5_port_set_eth_ptys to ensure the register was
successfully set before calling it.
Fixes: 667daedaecd1 ("net/mlx5e: Toggle link only after modifying port parameters")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-9-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 572f9caa9e7295f8c8822e4122c7ae8f1c412ff9 ]
On sync reset reload work, when remote host updates devlink on reload
actions performed on that host, it misses taking devlink lock before
calling devlink_remote_reload_actions_performed() which results in
triggering lock assert like the following:
WARNING: CPU: 4 PID: 1164 at net/devlink/core.c:261 devl_assert_locked+0x3e/0x50
…
CPU: 4 PID: 1164 Comm: kworker/u96:6 Tainted: G S W 6.10.0-rc2+ #116
Hardware name: Supermicro SYS-2028TP-DECTR/X10DRT-PT, BIOS 2.0 12/18/2015
Workqueue: mlx5_fw_reset_events mlx5_sync_reset_reload_work [mlx5_core]
RIP: 0010:devl_assert_locked+0x3e/0x50
…
Call Trace:
<TASK>
? __warn+0xa4/0x210
? devl_assert_locked+0x3e/0x50
? report_bug+0x160/0x280
? handle_bug+0x3f/0x80
? exc_invalid_op+0x17/0x40
? asm_exc_invalid_op+0x1a/0x20
? devl_assert_locked+0x3e/0x50
devlink_notify+0x88/0x2b0
? mlx5_attach_device+0x20c/0x230 [mlx5_core]
? __pfx_devlink_notify+0x10/0x10
? process_one_work+0x4b6/0xbb0
process_one_work+0x4b6/0xbb0
[…]
Fixes: 84a433a40d0e ("net/mlx5: Lock mlx5 devlink reload callbacks")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3fda84dc090390573cfbd0b1d70372663315de21 ]
The cited commit didn't change the body of the loop as it should.
It shouldn't be using MLX5_LAG_P1.
Fixes: 7e978e7714d6 ("net/mlx5: Lag, use actual number of lag ports")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0aa3ca956c46d849775eae1816cef8fe4bc8b50e ]
This function has a nested loop. The problem is that both the inside
and outside loop use the same variable as an iterator. I found this
via static analysis so I'm not sure the impact. It could be that it
loops forever or, more likely, the loop exits early.
Fixes: 3a616b92a9d1 ("net: mvpp2: Add TX flow control support for jumbo frames")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/eaa8f403-7779-4d81-973d-a9ecddc0bf6f@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6044ca26210ba72b3dcc649fae1cbedd9e6ab018 ]
It is read by data path and modified from process context on remote cpu
so it is needed to use WRITE_ONCE to clear the pointer.
Fixes: efc2214b6047 ("ice: Add support for XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 405d9999aa0b4ae467ef391d1d9c7e0d30ad0841 ]
Given that ice_qp_dis() is called under rtnl_lock, synchronize_net() can
be called instead of synchronize_rcu() so that XDP rings can finish its
job in a faster way. Also let us do this as earlier in XSK queue disable
flow.
Additionally, turn off regular Tx queue before disabling irqs and NAPI.
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1ff72a2f67791cd4ddad19ed830445f57b30e992 ]
When ice driver is spammed with multiple xdpsock instances and flow
control is enabled, there are cases when Rx queue gets stuck and unable
to reflect the disable state in QRX_CTRL register. Similar issue has
previously been addressed in commit 13a6233b033f ("ice: Add support to
enable/disable all Rx queues before waiting").
To workaround this, let us simply not wait for a disabled state as later
patch will make sure that regardless of the encountered error in the
process of disabling a queue pair, the Rx queue will be enabled.
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ec145a18687fec8dd97eeb4f30057fa4debef577 ]
Address a scenario in which XSK ZC Tx produces descriptors to XDP Tx
ring when link is either not yet fully initialized or process of
stopping the netdev has already started. To avoid this, add checks
against carrier readiness in ice_xsk_wakeup() and in ice_xmit_zc().
One could argue that bailing out early in ice_xsk_wakeup() would be
sufficient but given the fact that we produce Tx descriptors on behalf
of NAPI that is triggered for Rx traffic, the latter is also needed.
Bringing link up is an asynchronous event executed within
ice_service_task so even though interface has been brought up there is
still a time frame where link is not yet ok.
Without this patch, when AF_XDP ZC Tx is used simultaneously with stack
Tx, Tx timeouts occur after going through link flap (admin brings
interface down then up again). HW seem to be unable to transmit
descriptor to the wire after HW tail register bump which in turn causes
bit __QUEUE_STATE_STACK_XOFF to be set forever as
netdev_tx_completed_queue() sees no cleaned bytes on the input.
Fixes: 126cdfe1007a ("ice: xsk: Improve AF_XDP ZC Tx and use batching API")
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 799a829507506924add8a7620493adc1c3cfda30 ]
softirq may get lost if an Rx interrupt comes before we call
napi_enable. Move napi_enable in front of axienet_setoptions(), which
turns on the device, to address the issue.
Link: https://lists.gnu.org/archive/html/qemu-devel/2024-07/msg06160.html
Fixes: cc37610caaf8 ("net: axienet: implement NAPI and GRO receive")
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9dbebae2e3c338122716914fe105458f41e3a4a ]
The perfect_match parameter of the update_vlan_hash operation is __le16,
and is correctly converted from host byte-order in the lone caller,
stmmac_vlan_update().
However, the implementations of this caller, dwxgmac2_update_vlan_hash()
and dwxgmac2_update_vlan_hash(), both treat this parameter as host byte
order, using the following pattern:
u32 value = ...
...
writel(value | perfect_match, ...);
This is not correct because both:
1) value is host byte order; and
2) writel expects a host byte order value as it's first argument
I believe that this will break on big endian systems. And I expect it
has gone unnoticed by only being exercised on little endian systems.
The approach taken by this patch is to update the callback, and it's
caller to simply use a host byte order value.
Flagged by Sparse.
Compile tested only.
Fixes: c7ab0b8088d7 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3ba359c0cd6eb5ea772125a7aededb4a2d516684 ]
RCU use in bond_should_notify_peers() looks wrong, since it does
rcu_dereference(), leaves the critical section, and uses the
pointer after that.
Luckily, it's called either inside a nested RCU critical section
or with the RTNL held.
Annotate it with rcu_dereference_rtnl() instead, and remove the
inner RCU critical section.
Fixes: 4cb4f97b7e36 ("bonding: rebuild the lock use for bond_mii_monitor()")
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20240719094119.35c62455087d.I68eb9c0f02545b364b79a59f2110f2cf5682a8e2@changeid
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6ebbe97a488179f5dc85f2f1e0c89b486e99ee97 upstream.
While the iavf driver adds a s/w limit (128) on the number of FDIR
filters that the VF can request, a malicious VF driver can request more
than that and exhaust the resources for other VFs.
Add a similar limit in ice.
CC: stable@vger.kernel.org
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Suggested-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36e3b949e35964e22b9a57f960660fc599038dd4 upstream.
The NIC requires each TSO segment to not span more than 10
descriptors. NIC further requires each descriptor to not exceed
16KB - 1 (GVE_TX_MAX_BUF_SIZE_DQO).
The descriptors for an skb are generated by
gve_tx_add_skb_no_copy_dqo() for DQO RDA queue format.
gve_tx_add_skb_no_copy_dqo() loops through each skb frag and
generates a descriptor for the entire frag if the frag size is
not greater than GVE_TX_MAX_BUF_SIZE_DQO. If the frag size is
greater than GVE_TX_MAX_BUF_SIZE_DQO, it is split into descriptor(s)
of size GVE_TX_MAX_BUF_SIZE_DQO and a descriptor is generated for
the remainder (frag size % GVE_TX_MAX_BUF_SIZE_DQO).
gve_can_send_tso() checks if the descriptors thus generated for an
skb would meet the requirement that each TSO-segment not span more
than 10 descriptors. However, the current code misses an edge case
when a TSO segment spans multiple descriptors within a large frag.
This change fixes the edge case.
gve_can_send_tso() relies on the assumption that max gso size (9728)
is less than GVE_TX_MAX_BUF_SIZE_DQO and therefore within an skb
fragment a TSO segment can never span more than 2 descriptors.
Fixes: a57e5de476be ("gve: DQO: Add TX path")
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240724143431.3343722-1-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a17b9f590f6ec2b9f1b12b1db3bf1d181de6b272 upstream.
When changing the interface type we also need to update the bss_num, the
driver private data is searched based on a unique (bss_type, bss_num)
tuple, therefore every time bss_type changes, bss_num must also change.
This fixes for example an issue in which, after the mode changed, a
wireless scan on the changed interface would not finish, leading to
repeated -EBUSY messages to userspace when other scan requests were
sent.
Fixes: c606008b7062 ("mwifiex: Properly initialize private structure on interface type changes")
Cc: stable@vger.kernel.org
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240510110458.15475-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97d9fba9a812cada5484667a46e14a4c976ca330 upstream.
Currently, netconsole cleans up the netpoll structure before disabling
the target. This approach can lead to race conditions, as message
senders (write_ext_msg() and write_msg()) check if the target is
enabled before using netpoll. The sender can validate that the target is
enabled, but, the netpoll might be de-allocated already, causing
undesired behaviours.
This patch reverses the order of operations:
1. Disable the target
2. Clean up the netpoll structure
This change eliminates the potential race condition, ensuring that
no messages are sent through a partially cleaned-up netpoll structure.
Fixes: 2382b15bcc39 ("netconsole: take care of NETDEV_UNREGISTER event")
Cc: stable@vger.kernel.org
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240712143415.1141039-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c5118072e228e7e4385fc5ac46b2e31cf6c4f2d3 ]
Broadcom switches supported by the b53 driver use a chip-wide jumbo frame
configuration. In the commit referenced with the Fixes tag, the setting
is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient chip-wide maximum frame size for the CPU port.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports. This aligns the driver
to the behavior of other switch drivers.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 66b6095c264e1b4e0a441c6329861806504e06c6 ]
Marvell chips not supporting per-port jumbo frame size configurations use
a chip-wide frame size configuration. In the commit referenced with the
Fixes tag, the setting is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient maximum frame size for the CPU port. Specifically, sending
full-size frames from the CPU port on a MV88E6097 having a user port MTU
of 1500 bytes results in dropped frames.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports.
Fixes: 1baf0fac10fb ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c9741a03dc8e491e57b95fba0058ab46b7e506da ]
To have enough space to write all possible sprintf() args. Currently
'name' size is 16, but the first '%s' specifier may already need at
least 16 characters, since 'bnad->netdev->name' is used there.
For '%d' specifiers, assume that they require:
* 1 char for 'tx_id + tx_info->tcb[i]->id' sum, BNAD_MAX_TXQ_PER_TX is 8
* 2 chars for 'rx_id + rx_info->rx_ctrl[i].ccb->id', BNAD_MAX_RXP_PER_RX
is 16
And replace sprintf with snprintf.
Detected using the static analysis tool - Svace.
Fixes: 8b230ed8ec96 ("bna: Brocade 10Gb Ethernet device driver")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e909f489191b365364e9d636dec33b5dfd4e5eb ]
Looks like not all compilers allow strlen(constant) as
a constant, so don't do that. Instead, revert back to
defining the length as the first submission had it.
Fixes: b5d14b0c6716 ("wifi: virt_wifi: avoid reporting connection success with wrong SSID")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407090934.NnR1TUbW-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202407090944.mpwLHGt9-lkp@intel.com/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b5d14b0c6716fad7f0c94ac6e1d6f60a49f985c7 ]
When user issues a connection with a different SSID than the one
virt_wifi has advertised, the __cfg80211_connect_result() will
trigger the warning: WARN_ON(bss_not_found).
The issue is because the connection code in virt_wifi does not
check the SSID from user space (it only checks the BSSID), and
virt_wifi will call cfg80211_connect_result() with WLAN_STATUS_SUCCESS
even if the SSID is different from the one virt_wifi has advertised.
Eventually cfg80211 won't be able to find the cfg80211_bss and generate
the warning.
Fixed it by checking the SSID (from user space) in the connection code.
Fixes: c7cdba31ed8b ("mac80211-next: rtnetlink wifi simulation device")
Reported-by: syzbot+d6eb9cee2885ec06f5e3@syzkaller.appspotmail.com
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Link: https://patch.msgid.link/20240705023756.10954-1-en-wei.wu@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 85099c7ce4f9e64c66aa397cd9a37473637ab891 ]
In rtw89_sta_info_get_iter() 'status->he_gi' is compared to array size.
But then 'rate->he_gi' is used as array index instead of 'status->he_gi'.
This can lead to go beyond array boundaries in case of 'rate->he_gi' is
not equal to 'status->he_gi' and is bigger than array size. Looks like
"copy-paste" mistake.
Fix this mistake by replacing 'rate->he_gi' with 'status->he_gi'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240703210510.11089-1-amishin@t-argos.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c32fe1986f27cac329767d3497986e306cad1d5e ]
FEC_ECR_EN1588 bit gets cleared after MAC reset in `fec_stop()`, which
makes all 1588 functionality shut down, and all the extended registers
disappear, on link-down, making the adapter fall back to compatibility
"dumb mode". However, some functionality needs to be retained (e.g. PPS)
even without link.
Fixes: 6605b730c061 ("FEC: Add time stamping code and a PTP hardware clock")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/netdev/5fa9fadc-a89d-467a-aae9-c65469ff5fe1@lunn.ch/
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ff049886671ccd4e624a30ec464cb20e4c39a313 ]
Add defines for bits of ECR, RCR control registers, TX watermark etc.
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240212153717.10023-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c32fe1986f27 ("net: fec: Fix FEC_ECR_EN1588 being cleared on link-down")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d2b0ca38d362ebf16ca79cd7f309d5bb8b581deb ]
Currently for CCMP256, GCMP128 and GCMP256 ciphers, in ath11k_install_key()
IEEE80211_KEY_FLAG_GENERATE_IV_MGMT is not set. And in ath11k_mac_mgmt_tx_wmi()
a length of IEEE80211_CCMP_MIC_LEN is reserved for all ciphers.
This results in unexpected management frame drop in case either of above 3 ciphers
is used. The reason is, without IEEE80211_KEY_FLAG_GENERATE_IV_MGMT set, mac80211
will not generate CCMP/GCMP headers in frame for ath11k. Also MIC length reserved
is wrong. Such frame is dropped later by hardware:
ath11k_pci 0000:5a:00.0: mac tx mgmt frame, buf id 0
ath11k_pci 0000:5a:00.0: mgmt tx compl ev pdev_id 1, desc_id 0, status 1
From user point of view, we have observed very low throughput due to this issue:
action frames are all dropped so ADDBA response from DUT never reaches AP. AP
can not use aggregation thus throughput is low.
Fix this by setting IEEE80211_KEY_FLAG_GENERATE_IV_MGMT flag and by reserving proper
MIC length for those ciphers.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Tested-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Closes: https://lore.kernel.org/all/CADS+iDX5=JtJr0apAtAQ02WWBxgOFEv8G063vuGYwDTC8AVZaw@mail.gmail.com
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240605014826.22498-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 75d8d7a63065b18df9555dbaab0b42d4c6f20943 ]
ACLs that reside in the algorithmic TCAM (A-TCAM) in Spectrum-2 and
newer ASICs can share the same mask if their masks only differ in up to
8 consecutive bits. For example, consider the following filters:
# tc filter add dev swp1 ingress pref 1 proto ip flower dst_ip 192.0.2.0/24 action drop
# tc filter add dev swp1 ingress pref 1 proto ip flower dst_ip 198.51.100.128/25 action drop
The second filter can use the same mask as the first (dst_ip/24) with a
delta of 1 bit.
However, the above only works because the two filters have different
values in the common unmasked part (dst_ip/24). When entries have the
same value in the common unmasked part they create undesired collisions
in the device since many entries now have the same key. This leads to
firmware errors such as [1] and to a reduced scale.
Fix by adjusting the hash table key to only include the value in the
common unmasked part. That is, without including the delta bits. That
way the driver will detect the collision during filter insertion and
spill the filter into the circuit TCAM (C-TCAM).
Add a test case that fails without the fix and adjust existing cases
that check C-TCAM spillage according to the above limitation.
[1]
mlxsw_spectrum2 0000:06:00.0: EMAD reg access failed (tid=3379b18a00003394,reg_id=3027(ptce3),type=write,status=8(resource not available))
Fixes: c22291f7cf45 ("mlxsw: spectrum: acl: Implement delta for ERP")
Reported-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 97d833ceb27dc19f8777d63f90be4a27b5daeedf ]
ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM
(A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can
contain more ACLs (i.e., tc filters), but the number of masks in each
region (i.e., tc chain) is limited.
In order to mitigate the effects of the above limitation, the device
allows filters to share a single mask if their masks only differ in up
to 8 consecutive bits. For example, dst_ip/25 can be represented using
dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the
number of masks being used (and therefore does not support mask
aggregation), but can contain a limited number of filters.
The driver uses the "objagg" library to perform the mask aggregation by
passing it objects that consist of the filter's mask and whether the
filter is to be inserted into the A-TCAM or the C-TCAM since filters in
different TCAMs cannot share a mask.
The set of created objects is dependent on the insertion order of the
filters and is not necessarily optimal. Therefore, the driver will
periodically ask the library to compute a more optimal set ("hints") by
looking at all the existing objects.
When the library asks the driver whether two objects can be aggregated
the driver only compares the provided masks and ignores the A-TCAM /
C-TCAM indication. This is the right thing to do since the goal is to
move as many filters as possible to the A-TCAM. The driver also forbids
two identical masks from being aggregated since this can only happen if
one was intentionally put in the C-TCAM to avoid a conflict in the
A-TCAM.
The above can result in the following set of hints:
H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta
H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta
After getting the hints from the library the driver will start migrating
filters from one region to another while consulting the computed hints
and instructing the device to perform a lookup in both regions during
the transition.
Assuming a filter with mask X is being migrated into the A-TCAM in the
new region, the hints lookup will return H1. Since H2 is the parent of
H1, the library will try to find the object associated with it and
create it if necessary in which case another hints lookup (recursive)
will be performed. This hints lookup for {mask Y, A-TCAM} will either
return H2 or H3 since the driver passes the library an object comparison
function that ignores the A-TCAM / C-TCAM indication.
This can eventually lead to nested objects which are not supported by
the library [1].
Fix by removing the object comparison function from both the driver and
the library as the driver was the only user. That way the lookup will
only return exact matches.
I do not have a reliable reproducer that can reproduce the issue in a
timely manner, but before the fix the issue would reproduce in several
minutes and with the fix it does not reproduce in over an hour.
Note that the current usefulness of the hints is limited because they
include the C-TCAM indication and represent aggregation that cannot
actually happen. This will be addressed in net-next.
[1]
WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0
Modules linked in:
CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42
Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0
[...]
Call Trace:
<TASK>
__objagg_obj_get+0x2bb/0x580
objagg_obj_get+0xe/0x80
mlxsw_sp_acl_erp_mask_get+0xb5/0xf0
mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270
mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510
process_one_work+0x151/0x370
Fixes: 9069a3817d82 ("lib: objagg: implement optimization hints assembly and use hints for object creation")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c636fa85feb450ca414a10010ed05361a73c93a6 ]
The band_idx variable in the function wlc_lcnphy_tx_iqlo_cal() will
never be set to 1 as BCM4313 is the only device for which the LCN PHY
code is used. This is a 2G-only device.
Fixes: 5b435de0d786 ("net: wireless: add brcm80211 drivers")
Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240509231037.2014109-1-samasth.norway.ananda@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ed7f2afdd0e043a397677e597ced0830b83ba0b3 upstream.
The cited commit missed to check against the validity of the frame length
in the tap_get_user_xdp() path, which could cause a corrupted skb to be
sent downstack. Even before the skb is transmitted, the
tap_get_user_xdp()-->skb_set_network_header() may assume the size is more
than ETH_HLEN. Once transmitted, this could either cause out-of-bound
access beyond the actual length, or confuse the underlayer with incorrect
or inconsistent header length in the skb metadata.
In the alternative path, tap_get_user() already prohibits short frame which
has the length less than Ethernet header size from being transmitted.
This is to drop any frame shorter than the Ethernet header size just like
how tap_get_user() does.
CVE: CVE-2024-41090
Link: https://lore.kernel.org/netdev/1717026141-25716-1-git-send-email-si-wei.liu@oracle.com/
Fixes: 0efac27791ee ("tap: accept an array of XDP buffs through sendmsg()")
Cc: stable@vger.kernel.org
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20240724170452.16837-2-dongli.zhang@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 049584807f1d797fc3078b68035450a9769eb5c3 upstream.
The cited commit missed to check against the validity of the frame length
in the tun_xdp_one() path, which could cause a corrupted skb to be sent
downstack. Even before the skb is transmitted, the
tun_xdp_one-->eth_type_trans() may access the Ethernet header although it
can be less than ETH_HLEN. Once transmitted, this could either cause
out-of-bound access beyond the actual length, or confuse the underlayer
with incorrect or inconsistent header length in the skb metadata.
In the alternative path, tun_get_user() already prohibits short frame which
has the length less than Ethernet header size from being transmitted for
IFF_TAP.
This is to drop any frame shorter than the Ethernet header size just like
how tun_get_user() does.
CVE: CVE-2024-41091
Inspired-by: https://lore.kernel.org/netdev/1717026141-25716-1-git-send-email-si-wei.liu@oracle.com/
Fixes: 043d222f93ab ("tuntap: accept an array of XDP buffs through sendmsg()")
Cc: stable@vger.kernel.org
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20240724170452.16837-3-dongli.zhang@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4ec17ce716bdaf680288ce680b4621b52483cc96 ]
The WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK should be set based on the
WOWLAN_KEK_KCK_MATERIAL command version. Currently, the command
version in the firmware has advanced to 4, which prevents the
flag from being set correctly, fix that.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240703064026.a0f162108575.If1a9785727d2a1b0197a396680965df1b53d4096@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 77453e2b015b5ced5b3f45364dd5a72dfc3bdecb ]
Add the following Telit FN912 compositions:
0x3000: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=07 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=3000 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN912
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x3001: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=03 Lev=01 Prnt=03 Port=07 Cnt=01 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=3001 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN912
S: SerialNumber=92c4c4d8
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://patch.msgid.link/20240625102236.69539-1-dnlplm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0983d288caf984de0202c66641577b739caad561 ]
Below is a summary of how the driver stores a reference to an skb during
transmit:
tx_buff[free_map[consumer_index]]->skb = new_skb;
free_map[consumer_index] = IBMVNIC_INVALID_MAP;
consumer_index ++;
Where variable data looks like this:
free_map == [4, IBMVNIC_INVALID_MAP, IBMVNIC_INVALID_MAP, 0, 3]
consumer_index^
tx_buff == [skb=null, skb=<ptr>, skb=<ptr>, skb=null, skb=null]
The driver has checks to ensure that free_map[consumer_index] pointed to
a valid index but there was no check to ensure that this index pointed
to an unused/null skb address. So, if, by some chance, our free_map and
tx_buff lists become out of sync then we were previously risking an
skb memory leak. This could then cause tcp congestion control to stop
sending packets, eventually leading to ETIMEDOUT.
Therefore, add a conditional to ensure that the skb address is null. If
not then warn the user (because this is still a bug that should be
patched) and free the old pointer to prevent memleak/tcp problems.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d34d8163fd87978a6abd792e2d8ad849f4c3d57 ]
As the potential failure of usb_submit_urb(), it should be better to
return the err variable to catch the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/all/20240521041020.1519416-1-nichen@iscas.ac.cn
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e6dd2936ce7ce94a1915b799f8af8193ec628e87 ]
When HW rfkill is toggled to disable the RF, the flow to stop scan is
called. When trying to send the command to abort the scan, since
HW rfkill is toggled, the command is not sent due to rfkill being
asserted, and -ERFKILL is returned from iwl_trans_send_cmd(), but this
is silently ignored in iwl_mvm_send_cmd() and thus the scan abort flow
continues to wait for scan complete notification and fails. Since it
fails, the UID to type mapping is not cleared, and thus a warning is
later fired when trying to stop the interface.
To fix this, modify the UMAC scan abort flow to force sending the
scan abort command even when in rfkill, so stop the FW from accessing
the radio etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.8cbe2f8c1a97.Iffe235c12a919dafec88eef399eb1f7bae2c5bdb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 989830d1cf16bd149bf0690d889a9caef95fb5b1 ]
Ensure that the 6 GHz channel is configured with a valid direct BSSID,
avoiding any invalid or multicast BSSID addresses.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.91a631a0fe60.I2ea2616af9b8a2eaf959b156c69cf65a2f1204d4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 08b16d1b5997dc378533318e2a9cd73c7a898284 ]
The BIGTK cipher field was added to the kek_kck_material_cmd
but wasn't assigned. Fix that by differentiating between the
IGTK/BIGTK keys and assign the ciphers fields accordingly.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.7fd0b22b7267.Ie9b581652b74bd7806980364d59e1b2e78e682c0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b7ffca99313d856f7d1cc89038d9061b128e8e97 ]
After moving from commands to notificaitons in the d3 resume flow,
removing the WOWLAN_GET_STATUSES and REPLY_OFFLOADS_QUERY_CMD causes
the return of the default value when looking up their version.
Returning zero here results in the driver sending the not supported
NON_QOS_TX_COUNTER_CMD.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.8cabfd580614.If3a0db9851f56041f8f5360959354abd5379224a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 381a7d453fa2ac5f854a154d3c9b1bbb90c4f94f upstream.
KCSAN reports a race in wg_packet_send_keepalive, which is intentional:
BUG: KCSAN: data-race in wg_packet_send_keepalive / wg_packet_send_staged_packets
write to 0xffff88814cd91280 of 8 bytes by task 3194 on cpu 0:
__skb_queue_head_init include/linux/skbuff.h:2162 [inline]
skb_queue_splice_init include/linux/skbuff.h:2248 [inline]
wg_packet_send_staged_packets+0xe5/0xad0 drivers/net/wireguard/send.c:351
wg_xmit+0x5b8/0x660 drivers/net/wireguard/device.c:218
__netdev_start_xmit include/linux/netdevice.h:4940 [inline]
netdev_start_xmit include/linux/netdevice.h:4954 [inline]
xmit_one net/core/dev.c:3548 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3564
__dev_queue_xmit+0xeff/0x1d80 net/core/dev.c:4349
dev_queue_xmit include/linux/netdevice.h:3134 [inline]
neigh_connected_output+0x231/0x2a0 net/core/neighbour.c:1592
neigh_output include/net/neighbour.h:542 [inline]
ip6_finish_output2+0xa66/0xce0 net/ipv6/ip6_output.c:137
ip6_finish_output+0x1a5/0x490 net/ipv6/ip6_output.c:222
NF_HOOK_COND include/linux/netfilter.h:303 [inline]
ip6_output+0xeb/0x220 net/ipv6/ip6_output.c:243
dst_output include/net/dst.h:451 [inline]
NF_HOOK include/linux/netfilter.h:314 [inline]
ndisc_send_skb+0x4a2/0x670 net/ipv6/ndisc.c:509
ndisc_send_rs+0x3ab/0x3e0 net/ipv6/ndisc.c:719
addrconf_dad_completed+0x640/0x8e0 net/ipv6/addrconf.c:4295
addrconf_dad_work+0x891/0xbc0
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2706
worker_thread+0x525/0x730 kernel/workqueue.c:2787
kthread+0x1d7/0x210 kernel/kthread.c:388
ret_from_fork+0x48/0x60 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:242
read to 0xffff88814cd91280 of 8 bytes by task 3202 on cpu 1:
skb_queue_empty include/linux/skbuff.h:1798 [inline]
wg_packet_send_keepalive+0x20/0x100 drivers/net/wireguard/send.c:225
wg_receive_handshake_packet drivers/net/wireguard/receive.c:186 [inline]
wg_packet_handshake_receive_worker+0x445/0x5e0 drivers/net/wireguard/receive.c:213
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2706
worker_thread+0x525/0x730 kernel/workqueue.c:2787
kthread+0x1d7/0x210 kernel/kthread.c:388
ret_from_fork+0x48/0x60 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:242
value changed: 0xffff888148fef200 -> 0xffff88814cd91280
Mark this race as intentional by using the skb_queue_empty_lockless()
function rather than skb_queue_empty(), which uses READ_ONCE()
internally to annotate the race.
Cc: stable@vger.kernel.org
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://patch.msgid.link/20240704154517.1572127-5-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2fe3d6d2053c57f2eae5e85ca1656d185ebbe4e8 upstream.
KCSAN reports a race in the CPU round robin function, which, as the
comment points out, is intentional:
BUG: KCSAN: data-race in wg_packet_send_staged_packets / wg_packet_send_staged_packets
read to 0xffff88811254eb28 of 4 bytes by task 3160 on cpu 1:
wg_cpumask_next_online drivers/net/wireguard/queueing.h:127 [inline]
wg_queue_enqueue_per_device_and_peer drivers/net/wireguard/queueing.h:173 [inline]
wg_packet_create_data drivers/net/wireguard/send.c:320 [inline]
wg_packet_send_staged_packets+0x60e/0xac0 drivers/net/wireguard/send.c:388
wg_packet_send_keepalive+0xe2/0x100 drivers/net/wireguard/send.c:239
wg_receive_handshake_packet drivers/net/wireguard/receive.c:186 [inline]
wg_packet_handshake_receive_worker+0x449/0x5f0 drivers/net/wireguard/receive.c:213
process_one_work kernel/workqueue.c:3248 [inline]
process_scheduled_works+0x483/0x9a0 kernel/workqueue.c:3329
worker_thread+0x526/0x720 kernel/workqueue.c:3409
kthread+0x1d1/0x210 kernel/kthread.c:389
ret_from_fork+0x4b/0x60 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
write to 0xffff88811254eb28 of 4 bytes by task 3158 on cpu 0:
wg_cpumask_next_online drivers/net/wireguard/queueing.h:130 [inline]
wg_queue_enqueue_per_device_and_peer drivers/net/wireguard/queueing.h:173 [inline]
wg_packet_create_data drivers/net/wireguard/send.c:320 [inline]
wg_packet_send_staged_packets+0x6e5/0xac0 drivers/net/wireguard/send.c:388
wg_packet_send_keepalive+0xe2/0x100 drivers/net/wireguard/send.c:239
wg_receive_handshake_packet drivers/net/wireguard/receive.c:186 [inline]
wg_packet_handshake_receive_worker+0x449/0x5f0 drivers/net/wireguard/receive.c:213
process_one_work kernel/workqueue.c:3248 [inline]
process_scheduled_works+0x483/0x9a0 kernel/workqueue.c:3329
worker_thread+0x526/0x720 kernel/workqueue.c:3409
kthread+0x1d1/0x210 kernel/kthread.c:389
ret_from_fork+0x4b/0x60 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
value changed: 0xffffffff -> 0x00000000
Mark this race as intentional by using READ/WRITE_ONCE().
Cc: stable@vger.kernel.org
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://patch.msgid.link/20240704154517.1572127-4-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 948f991c62a4018fb81d85804eeab3029c6209f8 upstream.
On the parisc platform, the kernel issues kernel warnings because
swap_endian() tries to load a 128-bit IPv6 address from an unaligned
memory location:
Kernel: unaligned access to 0x55f4688c in wg_allowedips_insert_v6+0x2c/0x80 [wireguard] (iir 0xf3010df)
Kernel: unaligned access to 0x55f46884 in wg_allowedips_insert_v6+0x38/0x80 [wireguard] (iir 0xf2010dc)
Avoid such unaligned memory accesses by instead using the
get_unaligned_be64() helper macro.
Signed-off-by: Helge Deller <deller@gmx.de>
[Jason: replace src[8] in original patch with src+8]
Cc: stable@vger.kernel.org
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://patch.msgid.link/20240704154517.1572127-3-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a99afef17af66c276c1d6e6f4dbcac223eaf6ac upstream.
The amount of TX space in the hardware buffer is tracked in the tx_space
variable. The initial value is currently only set during driver probing.
After closing the interface and reopening it the tx_space variable has
the last value it had before close. If it is smaller than the size of
the first send packet after reopeing the interface the queue will be
stopped. The queue is woken up after receiving a TX interrupt but this
will never happen since we did not send anything.
This commit moves the initialization of the tx_space variable to the
ks8851_net_open function right before starting the TX queue. Also query
the value from the hardware instead of using a hard coded value.
Only the SPI chip variant is affected by this issue because only this
driver variant actually depends on the tx_space variable in the xmit
function.
Fixes: 3dc5d4454545 ("net: ks8851: Fix TX stall caused by TX buffer overrun")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <horms@kernel.org>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240709195845.9089-1-rwahl@gmx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0913ec336a6c0c4a2b296bd9f74f8e41c4c83c8c upstream.
When SMP is enabled and spinlocks are actually functional then there is
a deadlock with the 'statelock' spinlock between ks8851_start_xmit_spi
and ks8851_irq:
watchdog: BUG: soft lockup - CPU#0 stuck for 27s!
call trace:
queued_spin_lock_slowpath+0x100/0x284
do_raw_spin_lock+0x34/0x44
ks8851_start_xmit_spi+0x30/0xb8
ks8851_start_xmit+0x14/0x20
netdev_start_xmit+0x40/0x6c
dev_hard_start_xmit+0x6c/0xbc
sch_direct_xmit+0xa4/0x22c
__qdisc_run+0x138/0x3fc
qdisc_run+0x24/0x3c
net_tx_action+0xf8/0x130
handle_softirqs+0x1ac/0x1f0
__do_softirq+0x14/0x20
____do_softirq+0x10/0x1c
call_on_irq_stack+0x3c/0x58
do_softirq_own_stack+0x1c/0x28
__irq_exit_rcu+0x54/0x9c
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x38/0x50
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x64/0x68
__netif_schedule+0x6c/0x80
netif_tx_wake_queue+0x38/0x48
ks8851_irq+0xb8/0x2c8
irq_thread_fn+0x2c/0x74
irq_thread+0x10c/0x1b0
kthread+0xc8/0xd8
ret_from_fork+0x10/0x20
This issue has not been identified earlier because tests were done on
a device with SMP disabled and so spinlocks were actually NOPs.
Now use spin_(un)lock_bh for TX queue related locking to avoid execution
of softirq work synchronously that would lead to a deadlock.
Fixes: 3dc5d4454545 ("net: ks8851: Fix TX stall caused by TX buffer overrun")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <horms@kernel.org>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240706101337.854474-1-rwahl@gmx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
