| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 2f228d364da95ab58f63a3fedc00d5b2b7db16ab upstream.
Structs rx_desc_92d and rx_fwinfo_92d will not work for big endian
systems.
Delete rx_desc_92d because it's big and barely used, and instead use
the get_rx_desc_rxmcs and get_rx_desc_rxht functions, which work on big
endian systems too.
Fix rx_fwinfo_92d by duplicating four of its members in the correct
order.
Tested only with RTL8192DU, which will use the same code.
Tested only on a little endian system.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/698463da-5ef1-40c7-b744-fa51ad847caf@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7c0f48410f546772ac94a0f7b7291a15c4fc173 upstream.
Some (all?) management frames are incorrectly reported to mac80211 as
decrypted when actually the hardware did not decrypt them. This results
in speeds 3-5 times lower than expected, 20-30 Mbps instead of 100
Mbps.
Fix this by checking the encryption type field of the RX descriptor.
rtw88 does the same thing.
This fix was tested only with rtl8192du, which will use the same code.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/4d600435-f0ea-46b0-bdb4-e60f173da8dd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08b5d052d17a89bb8706b2888277d0b682dc1610 upstream.
Don't subtract 1 from the power index. This was added in commit
2fc0b8e5a17d ("rtl8xxxu: Add TX power base values for gen1 parts")
for unknown reasons. The vendor drivers don't do this.
Also correct the calculations of values written to
REG_OFDM0_X{C,D}_TX_IQ_IMBALANCE. According to the vendor driver,
these are used for TX power training.
With these changes rtl8xxxu sets the TX power of RTL8192CU the same
as the vendor driver.
None of this appears to have any effect on my RTL8192CU device.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/6ae5945b-644e-45e4-a78f-4c7d9c987910@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1cd4bc987abb2823836cbb8f887026011ccddc8a upstream.
Commit f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
has recently been added to vxlan mainly in the context of source
address snooping/learning so that when it is enabled, an entry in the
FDB is not being created for an invalid address for the corresponding
tunnel endpoint.
Before commit f58f45c1e5b9 vxlan was similarly behaving as geneve in
that it passed through whichever macs were set in the L2 header. It
turns out that this change in behavior breaks setups, for example,
Cilium with netkit in L3 mode for Pods as well as tunnel mode has been
passing before the change in f58f45c1e5b9 for both vxlan and geneve.
After mentioned change it is only passing for geneve as in case of
vxlan packets are dropped due to vxlan_set_mac() returning false as
source and destination macs are zero which for E/W traffic via tunnel
is totally fine.
Fix it by only opting into the is_valid_ether_addr() check in
vxlan_set_mac() when in fact source address snooping/learning is
actually enabled in vxlan. This is done by moving the check into
vxlan_snoop(). With this change, the Cilium connectivity test suite
passes again for both tunnel flavors.
Fixes: f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Bauer <mail@david-bauer.net>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Backport note: vxlan snooping/learning not supported in 6.8 or older,
so commit is simply a revert. ]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b3dc6e8003b500861fa307e9a3400c52e78e4d3a ]
Raw packet from PF_PACKET socket ontop of an IPv6-backed ipvlan device will
hit WARN_ON_ONCE() in sk_mc_loop() through sch_direct_xmit() path.
WARNING: CPU: 2 PID: 0 at net/core/sock.c:775 sk_mc_loop+0x2d/0x70
Modules linked in: sch_netem ipvlan rfkill cirrus drm_shmem_helper sg drm_kms_helper
CPU: 2 PID: 0 Comm: swapper/2 Kdump: loaded Not tainted 6.9.0+ #279
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:sk_mc_loop+0x2d/0x70
Code: fa 0f 1f 44 00 00 65 0f b7 15 f7 96 a3 4f 31 c0 66 85 d2 75 26 48 85 ff 74 1c
RSP: 0018:ffffa9584015cd78 EFLAGS: 00010212
RAX: 0000000000000011 RBX: ffff91e585793e00 RCX: 0000000002c6a001
RDX: 0000000000000000 RSI: 0000000000000040 RDI: ffff91e589c0f000
RBP: ffff91e5855bd100 R08: 0000000000000000 R09: 3d00545216f43d00
R10: ffff91e584fdcc50 R11: 00000060dd8616f4 R12: ffff91e58132d000
R13: ffff91e584fdcc68 R14: ffff91e5869ce800 R15: ffff91e589c0f000
FS: 0000000000000000(0000) GS:ffff91e898100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f788f7c44c0 CR3: 0000000008e1a000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
? __warn (kernel/panic.c:693)
? sk_mc_loop (net/core/sock.c:760)
? report_bug (lib/bug.c:201 lib/bug.c:219)
? handle_bug (arch/x86/kernel/traps.c:239)
? exc_invalid_op (arch/x86/kernel/traps.c:260 (discriminator 1))
? asm_exc_invalid_op (./arch/x86/include/asm/idtentry.h:621)
? sk_mc_loop (net/core/sock.c:760)
ip6_finish_output2 (net/ipv6/ip6_output.c:83 (discriminator 1))
? nf_hook_slow (net/netfilter/core.c:626)
ip6_finish_output (net/ipv6/ip6_output.c:222)
? __pfx_ip6_finish_output (net/ipv6/ip6_output.c:215)
ipvlan_xmit_mode_l3 (drivers/net/ipvlan/ipvlan_core.c:602) ipvlan
ipvlan_start_xmit (drivers/net/ipvlan/ipvlan_main.c:226) ipvlan
dev_hard_start_xmit (net/core/dev.c:3594)
sch_direct_xmit (net/sched/sch_generic.c:343)
__qdisc_run (net/sched/sch_generic.c:416)
net_tx_action (net/core/dev.c:5286)
handle_softirqs (kernel/softirq.c:555)
__irq_exit_rcu (kernel/softirq.c:589)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1043)
The warning triggers as this:
packet_sendmsg
packet_snd //skb->sk is packet sk
__dev_queue_xmit
__dev_xmit_skb //q->enqueue is not NULL
__qdisc_run
sch_direct_xmit
dev_hard_start_xmit
ipvlan_start_xmit
ipvlan_xmit_mode_l3 //l3 mode
ipvlan_process_outbound //vepa flag
ipvlan_process_v6_outbound
ip6_local_out
__ip6_finish_output
ip6_finish_output2 //multicast packet
sk_mc_loop //sk->sk_family is AF_PACKET
Call ip{6}_local_out() with NULL sk in ipvlan as other tunnels to fix this.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240529095633.613103-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf0497f53c8535f99b72041529d3f7708a6e2c0d ]
When fec_probe() fails or fec_drv_remove() needs to release the
fec queue and remove a NAPI context, therefore add a function
corresponding to fec_enet_init() and call fec_enet_deinit() which
does the opposite to release memory and remove a NAPI context.
Fixes: 59d0f7465644 ("net: fec: init multi queue date structure")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240524050528.4115581-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52a2f0608366a629d43dacd3191039c95fef74ba ]
LED Select (LED_SEL) bit in the LED General Purpose IO Configuration
register is used to determine the functionality of external LED pins
(Speed Indicator, Link and Activity Indicator, Full Duplex Link
Indicator). The default value for this bit is 0 when no EEPROM is
present. If a EEPROM is present, the default value is the value of the
LED Select bit in the Configuration Flags of the EEPROM. A USB Reset or
Lite Reset (LRST) will cause this bit to be restored to the image value
last loaded from EEPROM, or to be set to 0 if no EEPROM is present.
While configuring the dual purpose GPIO/LED pins to LED outputs in the
LED General Purpose IO Configuration register, the LED_SEL bit is changed
as 0 and resulting the configured value from the EEPROM is cleared. The
issue is fixed by using read-modify-write approach.
Fixes: f293501c61c5 ("smsc95xx: configure LED outputs")
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Link: https://lore.kernel.org/r/20240523085314.167650-1-Parthiban.Veerasooran@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8021b94b0412c37bcc79027c2e382086b6ce449 ]
enic_set_vf_port assumes that the nl attribute IFLA_PORT_PROFILE
is of length PORT_PROFILE_MAX and that the nl attributes
IFLA_PORT_INSTANCE_UUID, IFLA_PORT_HOST_UUID are of length PORT_UUID_MAX.
These attributes are validated (in the function do_setlink in rtnetlink.c)
using the nla_policy ifla_port_policy. The policy defines IFLA_PORT_PROFILE
as NLA_STRING, IFLA_PORT_INSTANCE_UUID as NLA_BINARY and
IFLA_PORT_HOST_UUID as NLA_STRING. That means that the length validation
using the policy is for the max size of the attributes and not on exact
size so the length of these attributes might be less than the sizes that
enic_set_vf_port expects. This might cause an out of bands
read access in the memcpys of the data of these
attributes in enic_set_vf_port.
Fixes: f8bd909183ac ("net: Add ndo_{set|get}_vf_port support for enic dynamic vnics")
Signed-off-by: Roded Zats <rzats@paloaltonetworks.com>
Link: https://lore.kernel.org/r/20240522073044.33519-1-rzats@paloaltonetworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
exhaustion
[ Upstream commit 5c74195d5dd977e97556e6fa76909b831c241230 ]
Previously, the driver incorrectly used rx_dropped to report device
buffer exhaustion.
According to the documentation, rx_dropped should not be used to count
packets dropped due to buffer exhaustion, which is the purpose of
rx_missed_errors.
Use rx_missed_errors as intended for counting packets dropped due to
buffer exhaustion.
Fixes: 269e6b3af3bf ("net/mlx5e: Report additional error statistics in get stats ndo")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b1c92f8e5371700fada307cc8fd2c51fa7bc8c1 ]
The assignment of pps_enable is protected by tmreg_lock, but the read
operation of pps_enable is not. So the Coverity tool reports a lock
evasion warning which may cause data race to occur when running in a
multithread environment. Although this issue is almost impossible to
occur, we'd better fix it, at least it seems more logically reasonable,
and it also prevents Coverity from continuing to issue warnings.
Fixes: 278d24047891 ("net: fec: ptp: Enable PPS output based on ptp clock")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240521023800.17102-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db9b31aa9bc56ff0d15b78f7e827d61c4a096e40 ]
Fix use after free when FW completion arrives while device is in
internal error state. Avoid calling completion handler in this case,
since the device will flush the command interface and trigger all
completions manually.
Kernel log:
------------[ cut here ]------------
refcount_t: underflow; use-after-free.
...
RIP: 0010:refcount_warn_saturate+0xd8/0xe0
...
Call Trace:
<IRQ>
? __warn+0x79/0x120
? refcount_warn_saturate+0xd8/0xe0
? report_bug+0x17c/0x190
? handle_bug+0x3c/0x60
? exc_invalid_op+0x14/0x70
? asm_exc_invalid_op+0x16/0x20
? refcount_warn_saturate+0xd8/0xe0
cmd_ent_put+0x13b/0x160 [mlx5_core]
mlx5_cmd_comp_handler+0x5f9/0x670 [mlx5_core]
cmd_comp_notifier+0x1f/0x30 [mlx5_core]
notifier_call_chain+0x35/0xb0
atomic_notifier_call_chain+0x16/0x20
mlx5_eq_async_int+0xf6/0x290 [mlx5_core]
notifier_call_chain+0x35/0xb0
atomic_notifier_call_chain+0x16/0x20
irq_int_handler+0x19/0x30 [mlx5_core]
__handle_irq_event_percpu+0x4b/0x160
handle_irq_event+0x2e/0x80
handle_edge_irq+0x98/0x230
__common_interrupt+0x3b/0xa0
common_interrupt+0x7b/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
Fixes: 51d138c2610a ("net/mlx5: Fix health error state handling")
Signed-off-by: Akiva Goldberger <agoldberger@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240509112951.590184-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d50729f1d60bca822ef6d9c1a5fb28d486bd7593 ]
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
v3: also fix a sparse error ( https://lore.kernel.org/oe-kbuild-all/202405091310.KvncIecx-lkp@intel.com/ )
v2: leave the skb_trim() game because smsc95xx_rx_csum_offload()
needs the csum part. (Jakub)
While we are it, use get_unaligned() in smsc95xx_rx_csum_offload().
Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Cc: UNGLinuxDriver@microchip.com
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509083313.2113832-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 812552808f7ff71133fc59768cdc253c5b8ca1bf ]
This fixes a probably long standing problem in the Cortina
Gemini ethernet driver: there are some paths in the code
where the IRQ registers are written without taking the proper
locks.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509-gemini-ethernet-locking-v1-1-afd00a528b95@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ac0a230f719b02432d8c7eba7615ebd691da86f4 ]
Erhard reports netpoll warnings from sungem:
netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll (gem_start_xmit+0x0/0x398)
WARNING: CPU: 1 PID: 1 at net/core/netpoll.c:370 netpoll_send_skb+0x1fc/0x20c
gem_poll_controller() disables interrupts, which may sleep.
We can't sleep in netpoll, it has interrupts disabled completely.
Strangely, gem_poll_controller() doesn't even poll the completions,
and instead acts as if an interrupt has fired so it just schedules
NAPI and exits. None of this has been necessary for years, since
netpoll invokes NAPI directly.
Fixes: fe09bb619096 ("sungem: Spring cleaning and GRO support")
Reported-and-tested-by: Erhard Furtner <erhard_f@mailbox.org>
Link: https://lore.kernel.org/all/20240428125306.2c3080ef@legion
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240508134504.3560956-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 05417aa9c0c038da2464a0c504b9d4f99814a23b ]
Some usb drivers set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: c9b37458e956 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506143939.3673865-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9aad6e45c4e7d16b2bb7c3794154b828fb4384b4 ]
Some usb drivers try to set small skb->truesize and break
core networking stacks.
I replace one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: 361459cd9642 ("net: usb: aqc111: Implement RX data path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506135546.3641185-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1d60eabb82694e58543e2b6366dae3e7465892a5 ]
This loop is supposed to copy the mac address to cmd->addr but the
i++ increment is missing so it copies everything to cmd->addr[0] and
only the last address is recorded.
Fixes: 22bedad3ce11 ("net: convert multicast list to list_head")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/b788be9a-15f5-4cca-a3fe-79df4c8ce7b2@moroto.mountain
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e120b6388d7d88635d67dcae6483f39c37111850 ]
Syzkaller reports [1] hitting a warning about an endpoint in use
not having an expected type to it.
Fix the issue by checking for the existence of all proper
endpoints with their according types intact.
Sadly, this patch has not been tested on real hardware.
[1] Syzkaller report:
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 3643 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
ar5523_cmd+0x41b/0x780 drivers/net/wireless/ath/ar5523/ar5523.c:275
ar5523_cmd_read drivers/net/wireless/ath/ar5523/ar5523.c:302 [inline]
ar5523_host_available drivers/net/wireless/ath/ar5523/ar5523.c:1376 [inline]
ar5523_probe+0x14b0/0x1d10 drivers/net/wireless/ath/ar5523/ar5523.c:1655
usb_probe_interface+0x30f/0x7f0 drivers/usb/core/driver.c:396
call_driver_probe drivers/base/dd.c:560 [inline]
really_probe+0x249/0xb90 drivers/base/dd.c:639
__driver_probe_device+0x1df/0x4d0 drivers/base/dd.c:778
driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:808
__device_attach_driver+0x1d4/0x2e0 drivers/base/dd.c:936
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:427
__device_attach+0x1e4/0x530 drivers/base/dd.c:1008
bus_probe_device+0x1e8/0x2a0 drivers/base/bus.c:487
device_add+0xbd9/0x1e90 drivers/base/core.c:3517
usb_set_configuration+0x101d/0x1900 drivers/usb/core/message.c:2170
usb_generic_driver_probe+0xbe/0x100 drivers/usb/core/generic.c:238
usb_probe_device+0xd8/0x2c0 drivers/usb/core/driver.c:293
call_driver_probe drivers/base/dd.c:560 [inline]
really_probe+0x249/0xb90 drivers/base/dd.c:639
__driver_probe_device+0x1df/0x4d0 drivers/base/dd.c:778
driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:808
__device_attach_driver+0x1d4/0x2e0 drivers/base/dd.c:936
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:427
__device_attach+0x1e4/0x530 drivers/base/dd.c:1008
bus_probe_device+0x1e8/0x2a0 drivers/base/bus.c:487
device_add+0xbd9/0x1e90 drivers/base/core.c:3517
usb_new_device.cold+0x685/0x10ad drivers/usb/core/hub.c:2573
hub_port_connect drivers/usb/core/hub.c:5353 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5497 [inline]
port_event drivers/usb/core/hub.c:5653 [inline]
hub_event+0x26cb/0x45d0 drivers/usb/core/hub.c:5735
process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289
worker_thread+0x669/0x1090 kernel/workqueue.c:2436
kthread+0x2e8/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306
</TASK>
Reported-and-tested-by: syzbot+1bc2c2afd44f820a669f@syzkaller.appspotmail.com
Fixes: b7d572e1871d ("ar5523: Add new driver")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240408121425.29392-1-n.zhandarovich@fintech.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6dd09b3dac89b45d1ea3e3bd035a3859c0369a0 ]
Syzkaller reports [1] hitting a warning which is caused by presence
of a wrong endpoint type at the URB sumbitting stage. While there
was a check for a specific 4th endpoint, since it can switch types
between bulk and interrupt, other endpoints are trusted implicitly.
Similar warning is triggered in a couple of other syzbot issues [2].
Fix the issue by doing a comprehensive check of all endpoints
taking into account difference between high- and full-speed
configuration.
[1] Syzkaller report:
...
WARNING: CPU: 0 PID: 4721 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
carl9170_usb_send_rx_irq_urb+0x273/0x340 drivers/net/wireless/ath/carl9170/usb.c:504
carl9170_usb_init_device drivers/net/wireless/ath/carl9170/usb.c:939 [inline]
carl9170_usb_firmware_finish drivers/net/wireless/ath/carl9170/usb.c:999 [inline]
carl9170_usb_firmware_step2+0x175/0x240 drivers/net/wireless/ath/carl9170/usb.c:1028
request_firmware_work_func+0x130/0x240 drivers/base/firmware_loader/main.c:1107
process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289
worker_thread+0x669/0x1090 kernel/workqueue.c:2436
kthread+0x2e8/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308
</TASK>
[2] Related syzkaller crashes:
Link: https://syzkaller.appspot.com/bug?extid=e394db78ae0b0032cb4d
Link: https://syzkaller.appspot.com/bug?extid=9468df99cb63a4a4c4e1
Reported-and-tested-by: syzbot+0ae4804973be759fa420@syzkaller.appspotmail.com
Fixes: a84fab3cbfdc ("carl9170: 802.11 rx/tx processing and usb backend")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Acked-By: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422183355.3785-1-n.zhandarovich@fintech.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f1f1b5b055c9f27a2f90fd0f0521f5920e9b3c18 ]
Specify board data size (and board.bin filename) for the WCN3990
platform.
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Fixes: 03a72288c546 ("ath10k: wmi: add hw params entry for wcn3990")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130-wcn3990-board-fw-v1-1-738f7c19a8c8@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
ath10k_dbg_sta_write_peer_debug_trigger()
[ Upstream commit c511a9c12674d246916bb16c479d496b76983193 ]
Clang Static Checker (scan-build) warns:
drivers/net/wireless/ath/ath10k/debugfs_sta.c:line 429, column 3
Value stored to 'ret' is never read.
Return 'ret' rather than 'count' when 'ret' stores an error code.
Fixes: ee8b08a1be82 ("ath10k: add debugfs support to get per peer tids log via tracing")
Signed-off-by: Su Hui <suhui@nfschina.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422034243.938962-1-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 954fd908f177604d4cce77e2a88cc50b29bad5ff ]
clang complains that the temporary string for the name passed into
alloc_workqueue() is too short for its contents:
drivers/net/ethernet/qlogic/qed/qed_main.c:1218:3: error: 'snprintf' will always be truncated; specified size is 16, but format string expands to at least 18 [-Werror,-Wformat-truncation]
There is no need for a temporary buffer, and the actual name of a workqueue
is 32 bytes (WQ_NAME_LEN), so just use the interface as intended to avoid
the truncation.
Fixes: 59ccf86fe69a ("qed: Add driver infrastucture for handling mfw requests.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240326223825.4084412-4-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e57b7d62a1b2f496caf0beba81cec3c90fad80d5 ]
Currently host relies on CE interrupts to get notified that
the service ready message is ready. This results in timeout
issue if the interrupt is not fired, due to some unknown
reasons. See below logs:
[76321.937866] ath10k_pci 0000:02:00.0: wmi service ready event not received
...
[76322.016738] ath10k_pci 0000:02:00.0: Could not init core: -110
And finally it causes WLAN interface bring up failure.
Change to give it one more chance here by polling CE rings,
before failing directly.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00157-QCARMSWPZ-1
Fixes: 5e3dd157d7e7 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices")
Reported-by: James Prestwood <prestwoj@gmail.com>
Tested-By: James Prestwood <prestwoj@gmail.com> # on QCA6174 hw3.2
Link: https://lore.kernel.org/linux-wireless/304ce305-fbe6-420e-ac2a-d61ae5e6ca1a@gmail.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240227030409.89702-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0b8fe5bd73249dc20be2e88a12041f8920797b59 ]
Add the following Telit FN920C04 compositions:
0x10a0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a4: rmnet + tty (AT) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a4 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a9: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a9 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5eefb477d21a26183bc3499aeefa991198315a2d upstream.
Compiling the m68k kernel with support for the ColdFire CPU family fails
with the following error:
In file included from drivers/net/ethernet/smsc/smc91x.c:80:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_reset’:
drivers/net/ethernet/smsc/smc91x.h:160:40: error: implicit declaration of function ‘_swapw’; did you mean ‘swap’? [-Werror=implicit-function-declaration]
160 | #define SMC_outw(lp, v, a, r) writew(_swapw(v), (a) + (r))
| ^~~~~~
drivers/net/ethernet/smsc/smc91x.h:904:25: note: in expansion of macro ‘SMC_outw’
904 | SMC_outw(lp, x, ioaddr, BANK_SELECT); \
| ^~~~~~~~
drivers/net/ethernet/smsc/smc91x.c:250:9: note: in expansion of macro ‘SMC_SELECT_BANK’
250 | SMC_SELECT_BANK(lp, 2);
| ^~~~~~~~~~~~~~~
cc1: some warnings being treated as errors
The function _swapw() was removed in commit d97cf70af097 ("m68k: use
asm-generic/io.h for non-MMU io access functions"), but is still used in
drivers/net/ethernet/smsc/smc91x.h.
Use ioread16be() and iowrite16be() to resolve the error.
Cc: stable@vger.kernel.org
Fixes: d97cf70af097 ("m68k: use asm-generic/io.h for non-MMU io access functions")
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240510113054.186648-2-thorsten.blum@toblux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0d5e2a82232605b337972fb2c7d0cbc46898aca1 upstream.
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d85cf67a339685beae1d0aee27b7f61da95455be upstream.
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d20f ("net: bcmgenet: power on MII block for all MII modes")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2dbe5f19368caae63b1f59f5bc2af78c7d522b3a upstream.
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
Fixes: 72f96347628e ("net: bcmgenet: set Rx mode before starting netif")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 094c281228529d333458208fd02fcac3b139d93b ]
There is a memory barrier in followed case. When set the port down,
hclgevf_set_timmer will set DOWN in state. Meanwhile, the service task has
different behaviour based on whether the state is DOWN. Thus, to make sure
service task see DOWN, use smp_mb__after_atomic after calling set_bit().
CPU0 CPU1
========================== ===================================
hclgevf_set_timer_task() hclgevf_periodic_service_task()
set_bit(DOWN,state) test_bit(DOWN,state)
pf also has this issue.
Fixes: ff200099d271 ("net: hns3: remove unnecessary work in hclgevf_main")
Fixes: 1c6dfe6fc6f7 ("net: hns3: remove mailbox and reset work in hclge_main")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d362046021ea122309da8c8e0b6850c792ca97b5 ]
Update the qmi_wwan driver support for the Rolling
LTE modules.
- VID:PID 33f8:0104, RW101-GL for laptop debug M.2 cards(with RMNET
interface for /Linux/Chrome OS)
0x0104: RMNET, diag, at, pipe
Here are the outputs of usb-devices:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=33f8 ProdID=0104 Rev=05.04
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=ba2eb033
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Vanillan Wang <vanillanwang@163.com>
Link: https://lore.kernel.org/r/20240416120713.24777-1-vanillanwang@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a6380cb4c6b5c1d6dad226ba3130f9090f0ccea ]
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
See: https://github.com/raspberrypi/firmware/issues/1882
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Maarten Vanraes <maarten@rmail.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b9a61c20179fda7bdfe2c1210aa72451991ab81a ]
The Topaz family (88E6141 and 88E6341) only support 256 Forwarding
Information Tables.
Fixes: a75961d0ebfd ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6341")
Fixes: 1558727a1c1b ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240429133832.9547-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9067eccdd7849dd120d5495dbd5a686fa6ed2c1a ]
The selftest for the driver sends a dummy packet and checks if the
packet will be received properly as it should be. The regular TX path
and the selftest can use the same network queue so locking is required
and was missing in the selftest path. This was addressed in the commit
cited below.
Unfortunately locking the TX queue requires BH to be disabled which is
not the case in selftest path which is invoked in process context.
Lockdep should be complaining about this.
Use __netif_tx_lock_bh() for TX queue locking.
Fixes: c650e04898072 ("cxgb4: Fix race between loopback and normal Tx path")
Reported-by: "John B. Wyatt IV" <jwyatt@redhat.com>
Closes: https://lore.kernel.org/all/Zic0ot5aGgR-V4Ks@thinkpad2021/
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240429091147.YWAaal4v@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f26f719a36e56381a1f4230e5364e7ad4d485888 ]
When calling qede_parse_actions() then the
return code was only used for a non-zero check,
and then -EINVAL was returned.
qede_parse_actions() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit broke the implicit assumption
that only -EINVAL would ever be returned.
Only compile tested.
Fixes: 319a1d19471e ("flow_offload: check for basic action hw stats type")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 27b44414a34b108c5a37cd5b4894f606061d86e7 ]
In qede_flow_spec_to_rule(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced qede_flow_spec_to_rule(),
and this call to qede_parse_flow_attr(), it looks
like it just duplicated how it was already used.
Only compile tested.
Fixes: 37c5d3efd7f8 ("qede: use ethtool_rx_flow_rule() to remove duplicated parser code")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fcee2065a178f78be6fd516302830378b17dba3d ]
In qede_add_tc_flower_fltr(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced these functions.
Only compile tested.
Fixes: 2ce9c93eaca6 ("qede: Ingress tc flower offload (drop action) support.")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e25714466abd9d96901b15efddf82c60a38abd86 ]
Explicitly set 'rc' (return code), before jumping to the
unlock and return path.
By not having any code depend on that 'rc' remains at
it's initial value of -EINVAL, then we can re-use 'rc' for
the return code of function calls in subsequent patches.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fcee2065a178 ("net: qede: use return from qede_parse_flow_attr() for flower")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f299ee709fb45036454ca11e90cb2810fe771878 ]
We try to access count + 1 byte from userspace with memdup_user(buffer,
count + 1). However, the userspace only provides buffer of count bytes and
only these count bytes are verified to be okay to access. To ensure the
copied buffer is NUL terminated, we use memdup_user_nul instead.
Fixes: 3a2eb515d136 ("octeontx2-af: Fix an off by one in rvu_dbg_qsize_write()")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-6-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c34096c7fdf272fd4c0c37fe411cd2e3ed0ee9f ]
Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from
userspace to that buffer. Later, we use sscanf on this buffer but we don't
ensure that the string is terminated inside the buffer, this can lead to
OOB read when using sscanf. Fix this issue by using memdup_user_nul
instead of memdup_user.
Fixes: 7afc5dbde091 ("bna: Add debugfs interface.")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-2-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e3eb7dd47bd4806f00e104eb6da092c435f9fb21 upstream.
b44_free_rings() accesses b44::rx_buffers (and ::tx_buffers)
unconditionally, but b44::rx_buffers is only valid when the
device is up (they get allocated in b44_open(), and deallocated
again in b44_close()), any other time these are just a NULL pointers.
So if you try to change the pause params while the network interface
is disabled/administratively down, everything explodes (which likely
netifd tries to do).
Link: https://github.com/openwrt/openwrt/issues/13789
Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2)
Cc: stable@vger.kernel.org
Reported-by: Peter Münster <pm@a16n.net>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Tested-by: Peter Münster <pm@a16n.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Peter Münster <pm@a16n.net>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/87y192oolj.fsf@a16n.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f5100da56b3980276234e812ce98d8f075194cd upstream.
Fix a cmd->ent use after free due to a race on command entry.
Such race occurs when one of the commands releases its last refcount and
frees its index and entry while another process running command flush
flow takes refcount to this command entry. The process which handles
commands flush may see this command as needed to be flushed if the other
process allocated a ent->idx but didn't set ent to cmd->ent_arr in
cmd_work_handler(). Fix it by moving the assignment of cmd->ent_arr into
the spin lock.
[70013.081955] BUG: KASAN: use-after-free in mlx5_cmd_trigger_completions+0x1e2/0x4c0 [mlx5_core]
[70013.081967] Write of size 4 at addr ffff88880b1510b4 by task kworker/26:1/1433361
[70013.081968]
[70013.082028] Workqueue: events aer_isr
[70013.082053] Call Trace:
[70013.082067] dump_stack+0x8b/0xbb
[70013.082086] print_address_description+0x6a/0x270
[70013.082102] kasan_report+0x179/0x2c0
[70013.082173] mlx5_cmd_trigger_completions+0x1e2/0x4c0 [mlx5_core]
[70013.082267] mlx5_cmd_flush+0x80/0x180 [mlx5_core]
[70013.082304] mlx5_enter_error_state+0x106/0x1d0 [mlx5_core]
[70013.082338] mlx5_try_fast_unload+0x2ea/0x4d0 [mlx5_core]
[70013.082377] remove_one+0x200/0x2b0 [mlx5_core]
[70013.082409] pci_device_remove+0xf3/0x280
[70013.082439] device_release_driver_internal+0x1c3/0x470
[70013.082453] pci_stop_bus_device+0x109/0x160
[70013.082468] pci_stop_and_remove_bus_device+0xe/0x20
[70013.082485] pcie_do_fatal_recovery+0x167/0x550
[70013.082493] aer_isr+0x7d2/0x960
[70013.082543] process_one_work+0x65f/0x12d0
[70013.082556] worker_thread+0x87/0xb50
[70013.082571] kthread+0x2e9/0x3a0
[70013.082592] ret_from_fork+0x1f/0x40
The logical relationship of this error is as follows:
aer_recover_work | ent->work
-------------------------------------------+------------------------------
aer_recover_work_func |
|- pcie_do_recovery |
|- report_error_detected |
|- mlx5_pci_err_detected |cmd_work_handler
|- mlx5_enter_error_state | |- cmd_alloc_index
|- enter_error_state | |- lock cmd->alloc_lock
|- mlx5_cmd_flush | |- clear_bit
|- mlx5_cmd_trigger_completions| |- unlock cmd->alloc_lock
|- lock cmd->alloc_lock |
|- vector = ~dev->cmd.vars.bitmask
|- for_each_set_bit |
|- cmd_ent_get(cmd->ent_arr[i]) (UAF)
|- unlock cmd->alloc_lock | |- cmd->ent_arr[ent->idx]=ent
The cmd->ent_arr[ent->idx] assignment and the bit clearing are not
protected by the cmd->alloc_lock in cmd_work_handler().
Fixes: 50b2412b7e78 ("net/mlx5: Avoid possible free of command entry while timeout comp handler")
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Shifeng Li <lishifeng@sangfor.com.cn>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1b9e743e923b256e353a9a644195372285e5a6c0 ]
The CPTS, by design, captures the messageType (Sync, Delay_Req, etc.)
field from the second nibble of the PTP header which is defined in the
PTPv2 (1588-2008) specification. In the PTPv1 (1588-2002) specification
the first two bytes of the PTP header are defined as the versionType
which is always 0x0001. This means that any PTPv1 packets that are
tagged for TX timestamping by the CPTS will have their messageType set
to 0x0 which corresponds to a Sync message type. This causes issues
when a PTPv1 stack is expecting a Delay_Req (messageType: 0x1)
timestamp that never appears.
Fix this by checking if the ptp_class of the timestamped TX packet is
PTP_CLASS_V1 and then matching the PTP sequence ID to the stored
sequence ID in the skb->cb data structure. If the sequence IDs match
and the packet is of type PTPv1 then there is a chance that the
messageType has been incorrectly stored by the CPTS so overwrite the
messageType stored by the CPTS with the messageType from the skb->cb
data structure. This allows the PTPv1 stack to receive TX timestamps
for Delay_Req packets which are necessary to lock onto a PTP Leader.
Signed-off-by: Jason Reeder <jreeder@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Ed Trexel <ed.trexel@hp.com>
Fixes: f6bd59526ca5 ("net: ethernet: ti: introduce am654 common platform time sync driver")
Link: https://lore.kernel.org/r/20240424071626.32558-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 54976cf58d6168b8d15cebb395069f23b2f34b31 ]
Same number of TCs doesn't imply that underlying TC configs are
same. The config could be different due to difference in number
of queues in each TC. Add utility function to determine if TC
configs are same.
Fixes: d5b33d024496 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Mineri Bhange <minerix.bhange@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240423182723.740401-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ef3c313119ea448c22da10366faa26b5b4b1a18e ]
If the MFS is set below the default (0x2600), a warning message is
reported like the following :
MFS for port 1 has been set below the default: 600
This message is a bit confusing as the number shown here (600) is in
fact an hexa number: 0x600 = 1536
Without any explicit "0x" prefix, this message is read like the MFS is
set to 600 bytes.
MFS, as per MTUs, are usually expressed in decimal base.
This commit reports both current and default MFS values in decimal
so it's less confusing for end-users.
A typical warning message looks like the following :
MFS for port 1 (1536) has been set below the default (9728)
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixes: 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set")
Link: https://lore.kernel.org/r/20240423182723.740401-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2cc7d150550cc981aceedf008f5459193282425c ]
Issue reported by customer during SRIOV testing, call trace:
When both i40e and the i40iw driver are loaded, a warning
in check_flush_dependency is being triggered. This seems
to be because of the i40e driver workqueue is allocated with
the WQ_MEM_RECLAIM flag, and the i40iw one is not.
Similar error was encountered on ice too and it was fixed by
removing the flag. Do the same for i40e too.
[Feb 9 09:08] ------------[ cut here ]------------
[ +0.000004] workqueue: WQ_MEM_RECLAIM i40e:i40e_service_task [i40e] is
flushing !WQ_MEM_RECLAIM infiniband:0x0
[ +0.000060] WARNING: CPU: 0 PID: 937 at kernel/workqueue.c:2966
check_flush_dependency+0x10b/0x120
[ +0.000007] Modules linked in: snd_seq_dummy snd_hrtimer snd_seq
snd_timer snd_seq_device snd soundcore nls_utf8 cifs cifs_arc4
nls_ucs2_utils rdma_cm iw_cm ib_cm cifs_md4 dns_resolver netfs qrtr
rfkill sunrpc vfat fat intel_rapl_msr intel_rapl_common irdma
intel_uncore_frequency intel_uncore_frequency_common ice ipmi_ssif
isst_if_common skx_edac nfit libnvdimm x86_pkg_temp_thermal
intel_powerclamp gnss coretemp ib_uverbs rapl intel_cstate ib_core
iTCO_wdt iTCO_vendor_support acpi_ipmi mei_me ipmi_si intel_uncore
ioatdma i2c_i801 joydev pcspkr mei ipmi_devintf lpc_ich
intel_pch_thermal i2c_smbus ipmi_msghandler acpi_power_meter acpi_pad
xfs libcrc32c ast sd_mod drm_shmem_helper t10_pi drm_kms_helper sg ixgbe
drm i40e ahci crct10dif_pclmul libahci crc32_pclmul igb crc32c_intel
libata ghash_clmulni_intel i2c_algo_bit mdio dca wmi dm_mirror
dm_region_hash dm_log dm_mod fuse
[ +0.000050] CPU: 0 PID: 937 Comm: kworker/0:3 Kdump: loaded Not
tainted 6.8.0-rc2-Feb-net_dev-Qiueue-00279-gbd43c5687e05 #1
[ +0.000003] Hardware name: Intel Corporation S2600BPB/S2600BPB, BIOS
SE5C620.86B.02.01.0013.121520200651 12/15/2020
[ +0.000001] Workqueue: i40e i40e_service_task [i40e]
[ +0.000024] RIP: 0010:check_flush_dependency+0x10b/0x120
[ +0.000003] Code: ff 49 8b 54 24 18 48 8d 8b b0 00 00 00 49 89 e8 48
81 c6 b0 00 00 00 48 c7 c7 b0 97 fa 9f c6 05 8a cc 1f 02 01 e8 35 b3 fd
ff <0f> 0b e9 10 ff ff ff 80 3d 78 cc 1f 02 00 75 94 e9 46 ff ff ff 90
[ +0.000002] RSP: 0018:ffffbd294976bcf8 EFLAGS: 00010282
[ +0.000002] RAX: 0000000000000000 RBX: ffff94d4c483c000 RCX:
0000000000000027
[ +0.000001] RDX: ffff94d47f620bc8 RSI: 0000000000000001 RDI:
ffff94d47f620bc0
[ +0.000001] RBP: 0000000000000000 R08: 0000000000000000 R09:
00000000ffff7fff
[ +0.000001] R10: ffffbd294976bb98 R11: ffffffffa0be65e8 R12:
ffff94c5451ea180
[ +0.000001] R13: ffff94c5ab5e8000 R14: ffff94c5c20b6e05 R15:
ffff94c5f1330ab0
[ +0.000001] FS: 0000000000000000(0000) GS:ffff94d47f600000(0000)
knlGS:0000000000000000
[ +0.000002] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ +0.000001] CR2: 00007f9e6f1fca70 CR3: 0000000038e20004 CR4:
00000000007706f0
[ +0.000000] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[ +0.000001] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[ +0.000001] PKRU: 55555554
[ +0.000001] Call Trace:
[ +0.000001] <TASK>
[ +0.000002] ? __warn+0x80/0x130
[ +0.000003] ? check_flush_dependency+0x10b/0x120
[ +0.000002] ? report_bug+0x195/0x1a0
[ +0.000005] ? handle_bug+0x3c/0x70
[ +0.000003] ? exc_invalid_op+0x14/0x70
[ +0.000002] ? asm_exc_invalid_op+0x16/0x20
[ +0.000006] ? check_flush_dependency+0x10b/0x120
[ +0.000002] ? check_flush_dependency+0x10b/0x120
[ +0.000002] __flush_workqueue+0x126/0x3f0
[ +0.000015] ib_cache_cleanup_one+0x1c/0xe0 [ib_core]
[ +0.000056] __ib_unregister_device+0x6a/0xb0 [ib_core]
[ +0.000023] ib_unregister_device_and_put+0x34/0x50 [ib_core]
[ +0.000020] i40iw_close+0x4b/0x90 [irdma]
[ +0.000022] i40e_notify_client_of_netdev_close+0x54/0xc0 [i40e]
[ +0.000035] i40e_service_task+0x126/0x190 [i40e]
[ +0.000024] process_one_work+0x174/0x340
[ +0.000003] worker_thread+0x27e/0x390
[ +0.000001] ? __pfx_worker_thread+0x10/0x10
[ +0.000002] kthread+0xdf/0x110
[ +0.000002] ? __pfx_kthread+0x10/0x10
[ +0.000002] ret_from_fork+0x2d/0x50
[ +0.000003] ? __pfx_kthread+0x10/0x10
[ +0.000001] ret_from_fork_asm+0x1b/0x30
[ +0.000004] </TASK>
[ +0.000001] ---[ end trace 0000000000000000 ]---
Fixes: 4d5957cbdecd ("i40e: remove WQ_UNBOUND and the task limit of our workqueue")
Signed-off-by: Sindhu Devale <sindhu.devale@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Robert Ganzynkowicz <robert.ganzynkowicz@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240423182723.740401-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fb4e2b70a7194b209fc7320bbf33b375f7114bd5 ]
The rehash delayed work is rescheduled with a delay if the number of
credits at end of the work is not negative as supposedly it means that
the migration ended. Otherwise, it is rescheduled immediately.
After "mlxsw: spectrum_acl_tcam: Fix possible use-after-free during
rehash" the above is no longer accurate as a non-negative number of
credits is no longer indicative of the migration being done. It can also
happen if the work encountered an error in which case the migration will
resume the next time the work is scheduled.
The significance of the above is that it is possible for the work to be
pending and associated with hints that were allocated when the migration
started. This leads to the hints being leaked [1] when the work is
canceled while pending as part of ACL region dismantle.
Fix by freeing the hints if hints are associated with a work that was
canceled while pending.
Blame the original commit since the reliance on not having a pending
work associated with hints is fragile.
[1]
unreferenced object 0xffff88810e7c3000 (size 256):
comm "kworker/0:16", pid 176, jiffies 4295460353
hex dump (first 32 bytes):
00 30 95 11 81 88 ff ff 61 00 00 00 00 00 00 80 .0......a.......
00 00 61 00 40 00 00 00 00 00 00 00 04 00 00 00 ..a.@...........
backtrace (crc 2544ddb9):
[<00000000cf8cfab3>] kmalloc_trace+0x23f/0x2a0
[<000000004d9a1ad9>] objagg_hints_get+0x42/0x390
[<000000000b143cf3>] mlxsw_sp_acl_erp_rehash_hints_get+0xca/0x400
[<0000000059bdb60a>] mlxsw_sp_acl_tcam_vregion_rehash_work+0x868/0x1160
[<00000000e81fd734>] process_one_work+0x59c/0xf20
[<00000000ceee9e81>] worker_thread+0x799/0x12c0
[<00000000bda6fe39>] kthread+0x246/0x300
[<0000000070056d23>] ret_from_fork+0x34/0x70
[<00000000dea2b93e>] ret_from_fork_asm+0x1a/0x30
Fixes: c9c9af91f1d9 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/0cc12ebb07c4d4c41a1265ee2c28b392ff997a86.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b377add0f0117409c418ddd6504bd682ebe0bf79 ]
Both the function that migrates all the chunks within a region and the
function that migrates all the entries within a chunk call
list_first_entry() on the respective lists without checking that the
lists are not empty. This is incorrect usage of the API, which leads to
the following warning [1].
Fix by returning if the lists are empty as there is nothing to migrate
in this case.
[1]
WARNING: CPU: 0 PID: 6437 at drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c:1266 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0>
Modules linked in:
CPU: 0 PID: 6437 Comm: kworker/0:37 Not tainted 6.9.0-rc3-custom-00883-g94a65f079ef6 #39
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0x2c0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x4a0
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 6f9579d4e302 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/4628e9a22d1d84818e28310abbbc498e7bc31bc9.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 743edc8547a92b6192aa1f1b6bb78233fa21dc9b ]
As previously explained, the rehash delayed work migrates filters from
one region to another. This is done by iterating over all chunks (all
the filters with the same priority) in the region and in each chunk
iterating over all the filters.
When the work runs out of credits it stores the current chunk and entry
as markers in the per-work context so that it would know where to resume
the migration from the next time the work is scheduled.
Upon error, the chunk marker is reset to NULL, but without resetting the
entry markers despite being relative to it. This can result in migration
being resumed from an entry that does not belong to the chunk being
migrated. In turn, this will eventually lead to a chunk being iterated
over as if it is an entry. Because of how the two structures happen to
be defined, this does not lead to KASAN splats, but to warnings such as
[1].
Fix by creating a helper that resets all the markers and call it from
all the places the currently only reset the chunk marker. For good
measures also call it when starting a completely new rehash. Add a
warning to avoid future cases.
[1]
WARNING: CPU: 7 PID: 1076 at drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:407 mlxsw_afk_encode+0x242/0x2f0
Modules linked in:
CPU: 7 PID: 1076 Comm: kworker/7:24 Tainted: G W 6.9.0-rc3-custom-00880-g29e61d91b77b #29
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_afk_encode+0x242/0x2f0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_entry_add+0xd9/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x109/0x290
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
</TASK>
Fixes: 6f9579d4e302 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/cc17eed86b41dd829d39b07906fec074a9ce580e.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ca3f7a7b61393804c46f170743c3b839df13977 ]
The rehash delayed work migrates filters from one region to another.
This is done by iterating over all chunks (all the filters with the same
priority) in the region and in each chunk iterating over all the
filters.
If the migration fails, the code tries to migrate the filters back to
the old region. However, the rollback itself can also fail in which case
another migration will be erroneously performed. Besides the fact that
this ping pong is not a very good idea, it also creates a problem.
Each virtual chunk references two chunks: The currently used one
('vchunk->chunk') and a backup ('vchunk->chunk2'). During migration the
first holds the chunk we want to migrate filters to and the second holds
the chunk we are migrating filters from.
The code currently assumes - but does not verify - that the backup chunk
does not exist (NULL) if the currently used chunk does not reference the
target region. This assumption breaks when we are trying to rollback a
rollback, resulting in the backup chunk being overwritten and leaked
[1].
Fix by not rolling back a failed rollback and add a warning to avoid
future cases.
[1]
WARNING: CPU: 5 PID: 1063 at lib/parman.c:291 parman_destroy+0x17/0x20
Modules linked in:
CPU: 5 PID: 1063 Comm: kworker/5:11 Tainted: G W 6.9.0-rc2-custom-00784-gc6a05c468a0b #14
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:parman_destroy+0x17/0x20
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_region_fini+0x19/0x60
mlxsw_sp_acl_tcam_region_destroy+0x49/0xf0
mlxsw_sp_acl_tcam_vregion_rehash_work+0x1f1/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 843500518509 ("mlxsw: spectrum_acl: Do rollback as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/d5edd4f4503934186ae5cfe268503b16345b4e0f.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5bcf925587e9b5d36420d572a0b4d131c90fb306 ]
In the rare cases when the device resources are exhausted it is likely
that the rehash delayed work will fail. An error message will be printed
whenever this happens which can be overwhelming considering the fact
that the work is per-region and that there can be hundreds of regions.
Fix by rate limiting the error message.
Fixes: e5e7962ee5c2 ("mlxsw: spectrum_acl: Implement region migration according to hints")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/c510763b2ebd25e7990d80183feff91cde593145.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
