| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dcb36 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* mvm: flush fw_dump_wk when mvm fails to start
* mvm: init card correctly on ctkill exit check
* pci: add a few more PCI subvendor IDs for the 7265 series
* fix firmware filename for 3160
* mvm: clear csa countdown when AP is stopped
* mvm: fix D3 firmware PN programming
* dvm: fix D3 firmware PN programming
* mvm: fix D3 CCMP TX PN assignment
rtlwifi:
* rtl8821ae: Fix system lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.
An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.
CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since vzalloc can be failed in memory pressure,
writes -ENOMEM to xenstore to indicate error.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because eth_type_trans() consumes ethernet header worth of bytes, a call
to read TCI from end of packet using rhine_rx_vlan_tag() no longer works
as it's reading from an invalid offset.
Tested to be working on PCEngines Alix board.
Fixes: 810f19bcb862 ("via-rhine: add consistent memory barrier in vlan receive code.")
Signed-off-by: Andrej Ota <andrej@ota.si>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under certain conditions EMAD responses can be returned from the device
even before setting trans_active. This will cause the EMAD Rx listener
to drop the EMAD response - as there are no active transactions - and
timeouts will be generated.
Fix this by setting trans_active before transmitting the EMAD skb.
Fixes: 4ec14b7634b2 ("mlxsw: Add interface to access registers and process events")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 435452aa8847 ("Prevent VFs from enabling VLAN promiscuous mode")
fixed the PF driver to not include the VLAN promisc capability while
provisioning the interface for a VF. But the fix did not remove this
capability from the profile descriptor of the VF. This causes the VF
driver to request this capability when it tries to create it's interface
at probe time. This could potentailly cause the VF probe to fail if the
FW enforces strict checking of the flags based on what was provisoned
by the PF. This strict checking is not being done by FW currently but
will be fixed in a future version. This patch fixes this issue by updating
the VF's profile descriptor so that they match the interface capability
flags provisioned by the PF.
Fixes: 435452aa8847 ("Prevent VFs from enabling VLAN promiscuous mode")
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FW requires the pf_num field in the cmd hdr to be set for it to return
the specific function's descriptors in the GET_PROFILE_CONFIG cmd. If not
set, the FW returns the descriptors of all the functions on the device.
If the first descriptor is not what is being queried for, the driver will
read wrong data. This patch fixes this issue by using the GET_CNTL_ATTRIB
cmd to query the real pci_func_num of a function and then uses it in the
GET_PROFILE_CONFIG cmd.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On BE3 chips in SRIOV configs, the TX path stalls when a packet less
than 32B is received from the host. A workaround to pad such packets
already exists for the Skyhawk and Lancer chips. Use the same workaround
for BE3 chips too.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mcc/mbox lock is not being released when be_cmd_copy() returns
an error.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the BE3 FW image, unlike Skyhawk's, the "asic_type_rev" field doesn't
track the asic_rev of chip it is compatible with. When asic_type_rev
is 0 the image is compatible only with pre-BE3-R chips (asic_rev < 0x10).
Fix the current compatibility check to take care of this.
We hit this issue when we try to flash old BE3 images (used prior to the
release of BE3-R) on pre-BE3-R adapters.
Fixes: a6e6ff6eee12f3e ("be2net: simplify UFI compatibility checking")
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit afae5ad78b342f401c28b0bb1adb3cd494cb125a
"net/fsl_pq_mdio: streamline probing of MDIO nodes"
added support for different types of MDIO devices:
1) Gianfar MDIO nodes that only map the MII registers
2) Gianfar MDIO nodes that map the full MDIO register set
3) eTSEC2 MDIO nodes (which map the full MDIO register set)
4) QE MDIO nodes (which map only the MII registers)
However, the implementation for types 1 and 4 would mistakenly assume
a mapping of the full MDIO register set, thereby computing the address
for the TBI register starting from the containing structure.
The TBI register would therefore be accessed at a wrong (much bigger)
address, not giving the expected result at all.
This patch restores the correct behavior we had prior to the above one.
The consequences of this bug are apparent when trying to access a PHY
with the same address as the value contained in the initial value of
the TBI register (normally 0); in that case you'll get answers from the
internal TBI device (even though MDIO/MDC pins are actually *also*
toggling on the physical bus!).
Beware that you also need to add a fake tbi node to your device tree
with an unused address.
Notice how this fix is related to commit
220669495bf8b68130a8218607147c7b74c28d2b
"powerpc: Add TBI PHY node to first MDIO bus"
which fixed the behavior in kernel 3.3, which was later broken by the
above commit on kernel 3.7.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Timur Tabi <timur@tabi.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When configuring the MDIO subsystem it is also necessary to configure
the TBI register. Make sure the TBI is contained within the mapped
register range in order to:
a) make sure the address is computed correctly
b) make users aware that we're actually accessing that register
In case of error, print a message but continue anyway.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Timur Tabi <timur@tabi.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configuring 4-tuple RSS hsahing for UDP
[E.g., by using `ethtool -N <interface> rx-flow-hash udp4 sdfn']
on a 57710/57711 adapter would cause it to assert as HW does not
support such a configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calculating the shift needed in order to access a bit array element
in a byte, we should multiply the index by the element size and not
assume it is fixed at 2-bits.
Fixes: 93c1edb27f9e ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 31557f0f9755 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the device was set to promiscuous mode, we didn't disable
VLAN filtering, which is wrong behaviour, fix that.
Now when the device is set to promiscuous mode RX packets
sent over any VLAN (or no VLAN tag at all) will be accepted.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We used the wrong register name for querying the PVLC register
Fixes: a124d13ef59e ('net/mlx5_core: Add more query port helpers')
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test interrupts fails if not all completion vectors called
request_irq. This case happens if only mlx4_en is loaded and
we have more completion vectors than rx rings.
Fixes: c66fa19c405a ('net/mlx4: Add EQ pool')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we get MAX_MSIX interrupts would like to have each receive ring
with his own msix interrupt line. Do not need the shared_ports
variable at mlx4_enable_msix
Fixes: 9293267a3e2a ('net/mlx4_core: Capping number of requested MSIXs to MAX_MSIX')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"Y" was the right answer for MDIO_OCTEON when this option was only
available on CAVIUM_OCTEON_SOC. But now that the option is visible on
all (64-bit) systems, this piece of advice no longer makes sense. This
helper module is selected automatically by drivers which need it
anyway.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: a6d6786452 ("net: mdio-octeon: Modify driver to work on both ThunderX and Octeon")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recently added mlxsw driver produces warnings in ARM
allmodconfig:
drivers/net/ethernet/mellanox/mlxsw/pci.c: In function 'mlxsw_pci_cmd_exec':
drivers/net/ethernet/mellanox/mlxsw/pci.c:1585:59: warning: right shift count >= width of type [-Wshift-count-overflow]
linux/byteorder/big_endian.h:38:51: note: in definition of macro '__cpu_to_be32'
drivers/net/ethernet/mellanox/mlxsw/pci.c:76:2: note: in expansion of macro 'iowrite32be'
This uses upper_32_bits() to extract the bits while avoiding that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Fixes: eda6500a987a "mlxsw: Add PCI bus implementation"
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The standard way to check if the AQ is enabled is to look at the
count field. So we should only set this field after we have
successfully allocated memory. To do otherwise is to incite
panic among the populace.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* some fixes for PN key programming when entering D3;
* fix for CSA when the AP is stopped during a channel switch;
* fix firmware name for 3160 devices;
* add some new PCI IDs for 7265 devices;
* fix CT-kill entry;
* fix kernel panic when a sysassert occurs in the init ucode flow;
|
|
The kasprintf function can return NULL if the allocation fails. Check for
successful allocation before attempting to use the returned buffer.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver still was not offloading TSO on GRE tunnels because
it forgot to set the GSO_GRE flag, causing lots of retransmits.
This fixes generic GRE traffic (like a tunnel added like below)
whereas before it would get 1Gb/s or less, now on a 10G adapter
it gets 8.7Gb/s.
ip ad ad 11.1.0.2/24 dev ens2f0
ip l set ens2f0 up
ip link add gre2 type gretap remote 11.1.0.1 local 11.1.0.2 dev ens2f0
ip l set gre2 up
ip ad ad 192.168.124.2/24 dev gre2
ping 192.168.124.1
netperf -H 192.168.124.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
pull-request: wireless-drivers 2015-10-01
ath9k:
* declare required extra tx headroom
ath10k:
* fix DMA related firmware crashes on multiple devices
rt2800usb:
* add usb ID 1b75:3070 for Airlive WT-2000USB
b43:
* probe bcma core (device) rev 0x15
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW dump may be triggered when running init ucode, for example due to a
sysassert. In this case fw_dump_wk may run after mvm is freed, resulting
in a kernel panic.
Fix it by flushing the work.
Fixes: 01b988a708af ("iwlwifi: mvm: allow to collect debug data when restart is disabled")
Cc: <stable@vger.kernel.org> [3.18+]
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
During the CT-kill exit flow, the card is powered up and partially
initialized to check if the temperature is already low enough.
Unfortunately the init bails early because the CT-kill flag is set.
Make the code bail early only for HW RF-kill, as was intended by the
author. CT-kill is self-imposed and is not really RF-kill.
Fixes: 31b8b343e019 ("iwlwifi: fix RFkill while calibrating")
Cc: <stable@vger.kernel.org> [3.18+]
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add 3 new subdevice IDs for the 0x095A device ID and 2 for the 0x095B
device ID.
Cc: <stable@vger.kernerl.org> [3.13+]
Reported-by: Jeremy <jeremy.bomkamp@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The MODULE_FIRMWARE() for 3160 should be using the 7260 version as
it's done in the device configuration struct instead of referencing
IWL3160_UCODE_API_OK which doesn't even exist.
Cc: <stable@vger.kernel.org> [3.8+]
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The csa_countdown flag was not cleared when the AP is stopped.
As a result, if the AP was stopped after csa_countdown had started,
all the folowing channel switch commands would fail.
Fix that by clearing the csa_countdown flag when the AP is stopped.
Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When going into/coming out of D3, the TX PN must be programmed into
and restored from the firmware respectively. The restore was broken
due to my previous commit to move PN assignment into the driver.
Sending the PN to the firmware still worked since we now use the
counter that's shared with mac80211, but accessing it through the
mac80211 API makes no sense now.
Fix this by reading/writing the counter directly. This actually
simplifies the code since we don't need to round-trip through the
key_seq structure.
Fixes: ca8c0f4bede6 ("iwlwifi: mvm: move TX PN assignment for CCMP to the driver")
Cc: <stable@vger.kernel.org> [4.1+]
Reported-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If common clock framework is configured, the driver generates warnings,
which are fixed by this change:
WARNING: CPU: 0 PID: 1 at linux/drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #141
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc_eth_drv_probe+0xfc/0x99c)
[<>] (lpc_eth_drv_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (lpc_eth_driver_init+0x18/0x20)
[<>] (lpc_eth_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If asix_rx_fixup_internal() fails to allocate rx->ax_skb, it will return
but not clear rx->size. rx points to driver private data. A later call
assumes that nonzero size means ax_skb was allocated and passes a null
ax_skb to skb_put. Changed allocation failure return to clear size first.
Found testing board with AX88772B devices.
Signed-off-by: David B. Robins <linux@davidrobins.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-09-30
this is a pull request of a single patch for 4.3.
The patch is by Stephane Grosjean and add support for the peak OEM PCI card to
the peak_pci driver by adding its device ID.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added kfree() to avoid the memory leak when debugfs_create_dir() fails.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release"),
pppoe_release() calls dev_put(po->pppoe_dev) if sk is in the
PPPOX_ZOMBIE state. But pppoe_flush_dev() can set sk->sk_state to
PPPOX_ZOMBIE _and_ reset po->pppoe_dev to NULL. This leads to the
following oops:
[ 570.140800] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e0
[ 570.142931] IP: [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe]
[ 570.144601] PGD 3d119067 PUD 3dbc1067 PMD 0
[ 570.144601] Oops: 0000 [#1] SMP
[ 570.144601] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppoe pppox ppp_generic slhc loop crc32c_intel ghash_clmulni_intel jitterentropy_rng sha256_generic hmac drbg ansi_cprng aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper acpi_cpufreq evdev serio_raw processor button ext4 crc16 mbcache jbd2 virtio_net virtio_blk virtio_pci virtio_ring virtio
[ 570.144601] CPU: 1 PID: 15738 Comm: ppp-apitest Not tainted 4.2.0 #1
[ 570.144601] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014
[ 570.144601] task: ffff88003d30d600 ti: ffff880036b60000 task.ti: ffff880036b60000
[ 570.144601] RIP: 0010:[<ffffffffa018c701>] [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe]
[ 570.144601] RSP: 0018:ffff880036b63e08 EFLAGS: 00010202
[ 570.144601] RAX: 0000000000000000 RBX: ffff880034340000 RCX: 0000000000000206
[ 570.144601] RDX: 0000000000000006 RSI: ffff88003d30dd20 RDI: ffff88003d30dd20
[ 570.144601] RBP: ffff880036b63e28 R08: 0000000000000001 R09: 0000000000000000
[ 570.144601] R10: 00007ffee9b50420 R11: ffff880034340078 R12: ffff8800387ec780
[ 570.144601] R13: ffff8800387ec7b0 R14: ffff88003e222aa0 R15: ffff8800387ec7b0
[ 570.144601] FS: 00007f5672f48700(0000) GS:ffff88003fc80000(0000) knlGS:0000000000000000
[ 570.144601] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 570.144601] CR2: 00000000000004e0 CR3: 0000000037f7e000 CR4: 00000000000406a0
[ 570.144601] Stack:
[ 570.144601] ffffffffa018f240 ffff8800387ec780 ffffffffa018f240 ffff8800387ec7b0
[ 570.144601] ffff880036b63e48 ffffffff812caabe ffff880039e4e000 0000000000000008
[ 570.144601] ffff880036b63e58 ffffffff812cabad ffff880036b63ea8 ffffffff811347f5
[ 570.144601] Call Trace:
[ 570.144601] [<ffffffff812caabe>] sock_release+0x1a/0x75
[ 570.144601] [<ffffffff812cabad>] sock_close+0xd/0x11
[ 570.144601] [<ffffffff811347f5>] __fput+0xff/0x1a5
[ 570.144601] [<ffffffff811348cb>] ____fput+0x9/0xb
[ 570.144601] [<ffffffff81056682>] task_work_run+0x66/0x90
[ 570.144601] [<ffffffff8100189e>] prepare_exit_to_usermode+0x8c/0xa7
[ 570.144601] [<ffffffff81001a26>] syscall_return_slowpath+0x16d/0x19b
[ 570.144601] [<ffffffff813babb1>] int_ret_from_sys_call+0x25/0x9f
[ 570.144601] Code: 48 8b 83 c8 01 00 00 a8 01 74 12 48 89 df e8 8b 27 14 e1 b8 f7 ff ff ff e9 b7 00 00 00 8a 43 12 a8 0b 74 1c 48 8b 83 a8 04 00 00 <48> 8b 80 e0 04 00 00 65 ff 08 48 c7 83 a8 04 00 00 00 00 00 00
[ 570.144601] RIP [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe]
[ 570.144601] RSP <ffff880036b63e08>
[ 570.144601] CR2: 00000000000004e0
[ 570.200518] ---[ end trace 46956baf17349563 ]---
pppoe_flush_dev() has no reason to override sk->sk_state with
PPPOX_ZOMBIE. pppox_unbind_sock() already sets sk->sk_state to
PPPOX_DEAD, which is the correct state given that sk is unbound and
po->pppoe_dev is NULL.
Fixes: 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release")
Tested-by: Oleksii Berezhniak <core@irc.lg.ua>
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 1277fa2ab2f9 ("rtlwifi: Remove the clear interrupt routine from all
drivers"), the code that cleared all interrupt enable bits before setting them
was removed for all PCI drivers. This fixed an issue that caused TX to be
blocked for 3-5 seconds. On some RTL8821AE units, this change causes soft
lockups to occur on boot. For that reason, the portion of the earlier commit
that applied to rtl8821ae is reverted. Kernels 4.1 and newer are affected.
See http://marc.info/?l=linux-wireless&m=144373370103285&w=2 and
https://bugzilla.opensuse.org/show_bug.cgi?id=944978 for two cases where
this regression affected user systems. Note that this bug does not appear on
any of the developer's setups. For those users whose systems are affected
by the TX blockage, but do not lock up on boot, a module parameter is added
to disable the interrupt clear
Fixes: 1277fa2ab2f9 ("rtlwifi: Remove the clear interrupt routine from all drivers")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V4.1+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull networking fixes from David Miller:
1) Fix regression in SKB partial checksum handling, from Pravin B
Shalar.
2) Fix VLAN inside of VXLAN handling in i40e driver, from Jesse
Brandeburg.
3) Cure softlockups during accept() in SCTP, from Karl Heiss.
4) MSG_PEEK should return multiple SKBs worth of data in AF_UNIX, from
Aaron Conole.
5) IPV6 erroneously ignores output interface specifier in lookup key for
route lookups, fix from David Ahern.
6) In Marvell DSA driver, forward unknown frames to CPU port, from
Andrew Lunn.
7) Mission flow flag initializations in some code paths, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Initialize flow flags in input path
net: dsa: fix preparation of a port STP update
testptp: Silence compiler warnings on ppc64
net/mlx4: Handle return codes in mlx4_qp_attach_common
dsa: mv88e6xxx: Enable forwarding for unknown to the CPU port
skbuff: Fix skb checksum partial check.
net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set
net sysfs: Print link speed as signed integer
bna: fix error handling
af_unix: return data from multiple SKBs on recv() with MSG_PEEK flag
af_unix: Convert the unix_sk macro to an inline function for type safety
net: sctp: Don't use 64 kilobyte lookup table for four elements
l2tp: protect tunnel->del_work by ref_count
net/ibm/emac: bump version numbers for correct work with ethtool
sctp: Prevent soft lockup when sctp_accept() is called during a timeout event
sctp: Whitespace fix
i40e/i40evf: check for stopped admin queue
i40e: fix VLAN inside VXLAN
r8169: fix handling rtl_readphy result
net: hisilicon: fix handling platform_get_irq result
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
- Fixes for mlx5 related issues
- Fixes for ipoib multicast handling
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: increase the max mcast backlog queue
IB/ipoib: Make sendonly multicast joins create the mcast group
IB/ipoib: Expire sendonly multicast joins
IB/mlx5: Remove pa_lkey usages
IB/mlx5: Remove support for IB_DEVICE_LOCAL_DMA_LKEY
IB/iser: Add module parameter for always register memory
xprtrdma: Replace global lkey with lkey local to PD
|
|
While new PEAK_PCIE_OEM_ID has been defined since 3.17, no corresponding
entry has been added in the peak_pci_tbl[] of the peak_pci CAN driver.
This patch enables now users of the PCAN-PCI Express OEM card to run the
peak_pci driver too.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Both new_steering_entry() and existing_steering_entry() return values
based on their success or failure, but currently they fall through
silently. This can make troubleshooting difficult, as we were unable
to tell which one of these two functions returned errors or
specifically what code was returned. This patch remedies that
situation by passing the return codes to err, which is returned by
mlx4_qp_attach_common() itself.
This also addresses a leak in the call to mlx4_bitmap_free() as well.
Signed-off-by: Robb Manes <rmanes@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Frames destined to an unknown address must be forwarded to the CPU
port. Otherwise incoming ARP, dhcp leases, etc, do not work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several functions can return negative value in case of error,
so their return type should be fixed as well as type of variables
to which this value is assigned.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The size of the MAC register dump used to be the size specified by the
reg property in the device tree. Userland has no good way of finding
out that size, and it was not specified consistently for each MAC type,
so ethtool would end up printing junk at the end of the register dump
if the device tree didn't match the size it assumed.
Using the new version numbers indicates unambiguously that the size of
the MAC register dump is dependent only on the MAC type.
Fixes: 5369c71f7ca2 ("net/ibm/emac: fix size of emac dump memory areas")
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's possible that while we are waiting for the spinlock, another
entity (that owns the spinlock) has shut down the admin queue.
If we then attempt to use the queue, we will panic.
Add a check for this condition on the receive side. This matches
an existing check on the send queue side.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
