| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c changes from Wolfram Sang:
- an arbitration driver. While the driver is quite simple, it caused
discussion if we need additional arbitration on top of the one
specified in the I2C standard. Conclusion is that I accept a few
generic mechanisms, but not very specific ones.
- the core lost the detach_adapter() call. It has no users anymore and
was in the way for other cleanups. attach_adapter() is sadly still
there since there are users waiting to be converted.
- the core gained a bus recovery infrastructure. I2C defines a way to
recover if the data line is stalled. This mechanism is now in the
core and drivers can now pass some data to make use of it.
- bigger driver cleanups for designware, s3c2410
- removing superfluous refcounting from drivers
- removing Ben Dooks as second maintainer due to inactivity. Thanks
for all your work so far, Ben!
- bugfixes, feature additions, devicetree fixups, simplifications...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: xiic: must always write 16-bit words to TX_FIFO
i2c: octeon: use HZ in timeout value
i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
i2c: designware-pci: drop superfluous {get|put}_device
i2c: designware-plat: drop superfluous {get|put}_device
i2c: davinci: drop superfluous {get|put}_device
MAINTAINERS: Ben Dooks is inactive regarding I2C
i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
i2c: at91: convert to dma_request_slave_channel_compat()
i2c: mxs: do error checking and handling in PIO mode
i2c: mxs: remove races in PIO code
i2c-designware: switch to use runtime PM autosuspend
i2c-designware: use usleep_range() in the busy-loop
i2c-designware: enable/disable the controller properly
i2c-designware: use dynamic adapter numbering on Lynxpoint
i2c-designware-pci: use managed functions pcim_* and devm_*
i2c-designware-pci: use dev_err() instead of printk()
i2c-designware: move to managed functions (devm_*)
i2c: remove CONFIG_HOTPLUG ifdefs
i2c: s3c2410: Add SMBus emulation for block read
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio & lguest updates from Rusty Russell:
"Lots of virtio work which wasn't quite ready for last merge window.
Plus I dived into lguest again, reworking the pagetable code so we can
move the switcher page: our fixmaps sometimes take more than 2MB now..."
Ugh. Annoying conflicts with the tcm_vhost -> vhost_scsi rename.
Hopefully correctly resolved.
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (57 commits)
caif_virtio: Remove bouncing email addresses
lguest: improve code readability in lg_cpu_start.
virtio-net: fill only rx queues which are being used
lguest: map Switcher below fixmap.
lguest: cache last cpu we ran on.
lguest: map Switcher text whenever we allocate a new pagetable.
lguest: don't share Switcher PTE pages between guests.
lguest: expost switcher_pages array (as lg_switcher_pages).
lguest: extract shadow PTE walking / allocating.
lguest: make check_gpte et. al return bool.
lguest: assume Switcher text is a single page.
lguest: rename switcher_page to switcher_pages.
lguest: remove RESERVE_MEM constant.
lguest: check vaddr not pgd for Switcher protection.
lguest: prepare to make SWITCHER_ADDR a variable.
virtio: console: replace EMFILE with EBUSY for already-open port
virtio-scsi: reset virtqueue affinity when doing cpu hotplug
virtio-scsi: introduce multiqueue support
virtio-scsi: push vq lock/unlock into virtscsi_vq_done
virtio-scsi: pass struct virtio_scsi to virtqueue completion function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"Here is a collection of fixes (and some intermixed cleanups) that were
considered less important and thus not included in the later parts of
the 3.9-rc cycle.
It's a bit all over the map, contents wise. A series of ux500 fixes
and cleanups, a bunch of various fixes for OMAP and tegra, and some
for Freescale i.MX and even Qualcomm MSM.
Note that there's also a patch on this branch to globally turn off
-Wmaybe-uninitialized when building with -Os. It's been posted
several times by Arnd and no dissent was raised, but nobody seemed
interested to pick it up. So here it is, as the topmost patch."
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
Turn off -Wmaybe-uninitialized when building with -Os
ARM: orion5x: include linux/cpu.h
ARM: tegra: call cpu_do_idle from C code
ARM: u300: fix ages old copy/paste bug
ARM: OMAP2+: add dependencies on ARCH_MULTI_V6/V7
ARM: tegra: solve adr range issue with THUMB2_KERNEL enabled
ARM: tegra: fix relocation truncated error when THUMB2_KERNEL enabled
ARM: tegra: fix build error when THUMB2_KERNEL enabled
ARM: msm: Fix uncompess.h tx underrun check
ARM: vexpress: Remove A9 PMU compatible values for non-A9 platforms
ARM: cpuimx27 and mbimx27: prepend CONFIG_ to Kconfig macro
ARM: OMAP2+: fix typo "CONFIG_BRIDGE_DVFS"
ARM: OMAP1: remove "config MACH_OMAP_HTCWIZARD"
ARM: mach-imx: mach-imx6q: Fix sparse warnings
ARM: mach-imx: src: Include "common.h
ARM: mach-imx: gpc: Include "common.h"
ARM: mach-imx: avic: Staticize *avic_base
ARM: mach-imx: tzic: Staticize *tzic_base
ARM: mach-imx: clk: Include "clk.h"
ARM: mach-imx: clk-busy: Staticize clk_busy_mux_ops
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
|
|
Use remove_proc_subtree() rather than remove_proc_entry() to remove a
device-specific proc directory and all its children.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jouni Malinen <j@w1.fi>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: linux-wireless@vger.kernel.org
cc: devel@driverdev.osuosl.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Use remove_proc_subtree() to remove the airo device subdir and all its
children instead of doing it manually.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-wireless@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Supply accessor functions to set attributes in proc_dir_entry structs.
The following are supplied: proc_set_size() and proc_set_user().
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cc: linuxppc-dev@lists.ozlabs.org
cc: linux-media@vger.kernel.org
cc: netdev@vger.kernel.org
cc: linux-wireless@vger.kernel.org
cc: linux-pci@vger.kernel.org
cc: netfilter-devel@vger.kernel.org
cc: alsa-devel@alsa-project.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
|
|
bnx2x driver allocates searcher T2 tables, but it releases that memory
during unload only released if the cnic is loaded.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the bnx2x driver reads the port configuration - mask irrelevant bits.
Without this change, the unintended bits may cause the driver to needlessly
toggle the link, as a comparison in the link flap avoidance flow will show
that the old link did not advertise the same capabilities and thus cannot
be retained.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove our (soon to be) bouncing email addresses,
and update Dmitri's address.
Dmitry will take over as maintainer for CAIF from now on.
Cc: Vikram Arv <vikram.arv@stericsson.com>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Dmity Tarnyagin <dmitry.tarnyagin@lockless.no>
|
|
Currently help message of /proc/sysrq-trigger highlight its upper-case
characters, like below:
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E)
memory-full-oom-kill(F) kill-all-tasks(I) ...
this would confuse user trigger sysrq by upper-case character, which is
inconsistent with the real lower-case character registed key.
This inconsistent help message will also lead more confused when
26 upper-case letters put into use in future.
This patch ethernet emac sysrq key: "emac(c)"
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit b6c39bfcf1d7d63 ("net/mlx4_en: Add a service task")
added a build error on 32bit arches.
ERROR: "__udivdi3" [drivers/net/ethernet/mellanox/mlx4/mlx4_en.ko]
undefined!
Fix this problem by using do_div()
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit d2d2d87dfd1a25ee270994c5b9e3eb4690428d32
("bnx2x: allow nvram test to run when device is down").
Since it makes access to the device in D3 state possible.
More work is required to make sure device is not set to D3
during ifdown. Until this is done the nvram-test should simply
exit if device is down like it did before.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the commit a11fbba (net/cpsw: fix irq_disable() with threaded interrupts)
from Sebastian Siewior, a kernel warning is generated as below. This warning
is generated as the irq_enabled is not initialized for the primary interface
and in probe it is initialized for the second interface. This patch moves
irq_enabled initialization from second interface to primary interface.
[ 3.049173] net eth0: phy found : id is : 0x4dd074
[ 3.054552] net eth0: phy found : id is : 0x4dd074
[ 3.070421] ------------[ cut here ]------------
[ 3.075308] WARNING: at kernel/irq/manage.c:437 enable_irq+0x3c/0x74()
[ 3.082173] Unbalanced enable for IRQ 56
[ 3.086299] Modules linked in:
[ 3.089557] [<c001abcc>] (unwind_backtrace+0x0/0xf0) from [<c004294c>] (warn_slowpath_common+0x4c/0x68)
[ 3.099450] [<c004294c>] (warn_slowpath_common+0x4c/0x68) from [<c00429fc>] (warn_slowpath_fmt+0x30/0x40)
[ 3.109521] [<c00429fc>] (warn_slowpath_fmt+0x30/0x40) from [<c00a29fc>] (enable_irq+0x3c/0x74)
[ 3.118681] [<c00a29fc>] (enable_irq+0x3c/0x74) from [<c03a7818>] (cpsw_ndo_open+0x61c/0x684)
[ 3.127669] [<c03a7818>] (cpsw_ndo_open+0x61c/0x684) from [<c0445c08>] (__dev_open+0x9c/0xf8)
[ 3.136646] [<c0445c08>] (__dev_open+0x9c/0xf8) from [<c0445e34>] (__dev_change_flags+0x78/0x13c)
[ 3.145988] [<c0445e34>] (__dev_change_flags+0x78/0x13c) from [<c0445f64>] (dev_change_flags+0x10/0x48)
[ 3.155884] [<c0445f64>] (dev_change_flags+0x10/0x48) from [<c0736d88>] (ip_auto_config+0x198/0x111c)
[ 3.165592] [<c0736d88>] (ip_auto_config+0x198/0x111c) from [<c00086a4>] (do_one_initcall+0x34/0x180)
[ 3.175309] [<c00086a4>] (do_one_initcall+0x34/0x180) from [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8)
[ 3.185393] [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8) from [<c04f36ec>] (kernel_init+0x8/0xe4)
[ 3.194929] [<c04f36ec>] (kernel_init+0x8/0xe4) from [<c00133d0>] (ret_from_fork+0x14/0x24)
[ 3.203712] ---[ end trace d6f979da080bc391 ]---
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Renesas R-Car based development boards, although a MAC address is printed on
all the Ethernet port labels, U-Boot doesn't write a valid MAC address to the
Ether MAHR/MALR registers (there's no storage provided for the Ether MAC address
either), so we have to resort to using a random MAC address...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The venerable 3c509 driver only sets its device parent in one case, the ISAPnP one.
It does this with the SET_NETDEV_DEV function. It should register with the device
hierarchy in two additional cases: standard (non-PnP) ISA and EISA.
- Currently they appear here:
/sys/devices/virtual/net/eth0 (standard ISA)
/sys/devices/virtual/net/eth1 (EISA)
- Rather, they should instead be here:
/sys/devices/isa/3c509.0/net/eth0 (standard ISA)
/sys/devices/pci0000:00/0000:00:07.0/00:04/net/eth1 (EISA)
Tested on ISA and EISA boards.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit f233a976ad15c3b8c54c0157f3c41d23f7514279 (tg3: shows
HW time stamping support only if ptp_capable is present) didn't
append hardware flags correctly. This patch fixes it.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 update from Catalin Marinas:
"Main features:
- Versatile Express SoC (model) support - DT files and Kconfig
entries (there are no arch/arm64/mach-* directories). The bulk of
the code has already been moved to drivers/ as part of the ARM SoC
clean-up.
- Basic multi-cluster support (CPU logical map initialised from the
DT)
- Simple earlyprintk support for UART 8250/16550 and FastModel
console output
- Optimised kernel library bitops and string functions.
- Automatic initialisation of the irqchip and clocks via DT"
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: (26 commits)
arm64: Use acquire/release semantics instead of explicit DMB
arm64: klib: bitops: fix unpredictable stxr usage
arm64: vexpress: Enable ARMv8 RTSM model (SoC) support
arm64: vexpress: Add dts files for the ARMv8 RTSM models
arm64: Survive invalid cpu enable-methods
arm64: mm: Correct show_pte behaviour
arm64: Fix compat types affecting struct compat_stat
arm64: Execute DSB during thread switching for TLB/cache maintenance
arm64: compiling issue, need add include/asm/vga.h file
arm64: smp: honour #address-size when parsing CPU reg property
arm64: Define cmpxchg64 and cmpxchg64_local for outside use
arm64: Define readq and writeq for driver module using
arm64: Fix task tracing
arm64: add explicit symbols to ESR_EL1 decoding
arm64: Use irqchip_init() for interrupt controller initialisation
arm64: psci: Use the MPIDR values from cpu_logical_map for cpu ids.
arm64: klib: Optimised atomic bitops
arm64: klib: Optimised string functions
arm64: klib: Optimised memory functions
arm64: head: match all affinity levels in the pen of the secondaries
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual stuff, mostly comment fixes, typo fixes, printk fixes and small
code cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (45 commits)
mm: Convert print_symbol to %pSR
gfs2: Convert print_symbol to %pSR
m32r: Convert print_symbol to %pSR
iostats.txt: add easy-to-find description for field 6
x86 cmpxchg.h: fix wrong comment
treewide: Fix typo in printk and comments
doc: devicetree: Fix various typos
docbook: fix 8250 naming in device-drivers
pata_pdc2027x: Fix compiler warning
treewide: Fix typo in printks
mei: Fix comments in drivers/misc/mei
treewide: Fix typos in kernel messages
pm44xx: Fix comment for "CONFIG_CPU_IDLE"
doc: Fix typo "CONFIG_CGROUP_CGROUP_MEMCG_SWAP"
mmzone: correct "pags" to "pages" in comment.
kernel-parameters: remove outdated 'noresidual' parameter
Remove spurious _H suffixes from ifdef comments
sound: Remove stray pluses from Kconfig file
radio-shark: Fix printk "CONFIG_LED_CLASS"
doc: put proper reference to CONFIG_MODULE_SIG_ENFORCE
...
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
A few more stragglers intended for 3.10...
For the Bluetooth bits, Gustavo says:
"A few more patches intended for 3.10, the most important one is the support in
btusb for fw loading for the Intel Bluetooth device. Other than that we have
only fixes and clean ups."
For the iwlwifi bits, Johannes says:
"Here are a few more changes for the 3.10 stream, some bugfixes,
adjustments to some powersave parameters and a new device ID."
For the NFC bits, Samuel says:
"This pull request includes Marcel's Kconfig dependency fix on top of the LLCP
code move to net/nfc."
On top of that...Yogesh Ashok Powar provides a few PCI-related mwifiex
updates, Hauke Mehrtens provides a small ssb feature for spurious
tone avoidance on a specific chip, and Larry Finger provides a small
rtlwifi fix related to avoiding false detection of AP loss.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Jouni Malinen <j@w1.fi>
cc: John W. Linville <linville@tuxdriver.com>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: linux-wireless@vger.kernel.org
cc: netdev@vger.kernel.org
cc: devel@driverdev.osuosl.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Simon Kelley <simon@thekelleys.org.uk>
cc: John W. Linville <linville@tuxdriver.com>
cc: linux-wireless@vger.kernel.org
cc: netdev@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since SKB_GSO_* flags are set by appropriate gso_segment callback
in TCP/UDP layer.
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer firmware can post CPL_SGE_EGR_UPDATE message encapsulated in a
CPL_FW4_MSG as follows
flit0 rss_header (if DropRSS == 0 in IQ context)
flit1 CPL_FW4_MSG cpl
flit2 rss_header w/opcode CPL_SGE_EGR_UPDATE
flit3 CPL_SGE_EGR_UPDATE cpl
So FW4_MSG CPLs with a newly created type of FW_TYPE_RSSCPL have the
CPL_SGE_EGR_UPDATE CPL message in flit 2 of the FW4_MSG. Firmware can still
post regular CPL_SGE_EGR_UPDATE messages, so the drivers need to handle
both.
This patch also writes a new parameter to firmware requesting encapsulated
EGR_UPDATE. This allows firmware with this support to not break older drivers.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer firmware can post CPL_SGE_EGR_UPDATE message encapsulated in a
CPL_FW4_MSG as follows
flit0 rss_header (if DropRSS == 0 in IQ context)
flit1 CPL_FW4_MSG cpl
flit2 rss_header w/opcode CPL_SGE_EGR_UPDATE
flit3 CPL_SGE_EGR_UPDATE cpl
So FW4_MSG CPLs with a newly created type of FW_TYPE_RSSCPL have the
CPL_SGE_EGR_UPDATE CPL message in flit 2 of the FW4_MSG. Firmware can still
post regular CPL_SGE_EGR_UPDATE messages, so the drivers need to handle
both.
This patch also writes a new parameter to firmware requesting encapsulated
EGR_UPDATE. This allows firmware with this support to not break older drivers.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea
fixes, which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while"
* tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (568 commits)
USB: ehci-msm: USB_MSM_OTG needs USB_PHY
USB: OHCI: avoid conflicting platform drivers
USB: OMAP: ISP1301 needs USB_PHY
USB: lpc32xx: ISP1301 needs USB_PHY
USB: ftdi_sio: enable two UART ports on ST Microconnect Lite
usb: phy: tegra: don't call into tegra-ehci directly
usb: phy: phy core cannot yet be a module
USB: Fix initconst in ehci driver
usb-storage: CY7C68300A chips do not support Cypress ATACB
USB: serial: option: Added support Olivetti Olicard 145
USB: ftdi_sio: correct ST Micro Connect Lite PIDs
ARM: mxs_defconfig: add CONFIG_USB_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY
usb: phy: remove exported function from __init section
usb: gadget: zero: put function instances on unbind
usb: gadget: f_sourcesink.c: correct a copy-paste misnomer
usb: gadget: cdc2: fix error return code in cdc_do_config()
usb: gadget: multi: fix error return code in rndis_do_config()
usb: gadget: f_obex: fix error return code in obex_bind()
USB: storage: convert to use module_usb_driver()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg Kroah-Hartman:
"Here's the big tty/serial driver merge request for 3.10-rc1
Once again, Jiri has a number of TTY driver fixes and cleanups, and
Peter Hurley came through with a bunch of ldisc fixes that resolve a
number of reported issues. There are some other serial driver
cleanups as well.
All of these have been in the linux-next tree for a while"
* tag 'tty-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (117 commits)
tty/serial/sirf: fix MODULE_DEVICE_TABLE
serial: mxs: drop superfluous {get|put}_device
serial: mxs: fix buffer overflow
ARM: PL011: add support for extended FIFO-size of PL011-r1p5
serial_core.c: add put_device() after device_find_child()
tty: Fix unsafe bit ops in tty_throttle_safe/unthrottle_safe
serial: sccnxp: Replace pdata.init/exit with regulator API
serial: sccnxp: Do not override device name
TTY: pty, fix compilation warning
TTY: rocket, fix compilation warning
TTY: ircomm: fix DTR being raised on hang up
TTY: synclinkmp: fix DTR being raised on hang up
TTY: synclink_gt: fix DTR being raised on hang up
TTY: synclink: fix DTR being raised on hang up
serial: 8250_dw: Fix the stub for dw8250_probe_acpi()
serial: 8250_dw: Convert to devm_ioremap()
serial: 8250_dw: Set port capabilities based on CPR register
serial: 8250_dw: Let ACPI code extract the DMA client info
serial: 8250_dw: Support clk framework also with ACPI
serial: 8250_dw: Enable runtime PM
...
|
|
Current tg3 shows hardware timestamping support for all devices
when that is true only for the hardware with PTP_CAPABLE flag
present.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lancer FW requires that the first cmd issued by the host-driver be an FLR.
So, re-order be_probe() to move be_cmd_function_reset() ahead of
be_cmd_fw_init().
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skyhawk-R requires V1 version of GET_FUNCTION_CONFIG cmd to be used for
querrying resources available per function.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for another ARM member of the R-Car family, R-Car M1A, also known as
R8A77781 -- it will share the code with previously added R8A77790.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver update from Greg Kroah-Hartman:
"Here's the big char / misc driver update for 3.10-rc1
A number of various driver updates, the majority being new
functionality in the MEI driver subsystem (it's now a subsystem, it
started out just a single driver), extcon updates, memory updates,
hyper-v updates, and a bunch of other small stuff that doesn't fit in
any other tree.
All of these have been in linux-next for a while"
* tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (148 commits)
Tools: hv: Fix a checkpatch warning
tools: hv: skip iso9660 mounts in hv_vss_daemon
tools: hv: use FIFREEZE/FITHAW in hv_vss_daemon
tools: hv: use getmntent in hv_vss_daemon
Tools: hv: Fix a checkpatch warning
tools: hv: fix checks for origin of netlink message in hv_vss_daemon
Tools: hv: fix warnings in hv_vss_daemon
misc: mark spear13xx-pcie-gadget as broken
mei: fix krealloc() misuse in in mei_cl_irq_read_msg()
mei: reduce flow control only for completed messages
mei: reseting -> resetting
mei: fix reading large reposnes
mei: revamp mei_irq_read_client_message function
mei: revamp mei_amthif_irq_read_message
mei: revamp hbm state machine
Revert "drivers/scsi: use module_pcmcia_driver() in pcmcia drivers"
Revert "scsi: pcmcia: nsp_cs: remove module init/exit function prototypes"
scsi: pcmcia: nsp_cs: remove module init/exit function prototypes
mei: wd: fix line over 80 characters
misc: tsl2550: Use dev_pm_ops
...
|
|
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed: warning: cast from pointer to integer of different size
The Hyper-V hosts always use 64 bit request id. The guests can have 32 or 64
bit pointers which equal to the ulong type size. So we cast it to ulong type.
And, assigning 32bit integer to 64 bit variable works fine.
The VMBus returns the same id in the completion packet. But the value has no
effect on the host side.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pegasus driver used single callback for sync and async control URBs.
Special flags were employed to distinguish between both, but due to flawed
logic it didn't always work. As a result of this change
[get|set]_registers() are now much simpler. Async write is also leaner
and does not use single, statically allocated memory for usb_ctrlrequest,
which is another potential race when asynchronously submitting URBs.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Duplicated code in routines reading and writing MII registers is now
packed in __mii_op().
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The socket buffer pool for the receive path is now gone. It's existence
didn't make much difference (performance-wise) and the code is better off
without the spinlocks protecting it.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow configuring the default destination port on a per-device basis.
Adds new netlink paramater IFLA_VXLAN_PORT to allow setting destination
port when creating new vxlan.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than computing source port and returning it in host order
then swapping later, go ahead and compute it in network order to
start with. Cleaner and less error prone.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Source compatiability for build iproute2 was broken by:
commit c7995c43facc6e5dea4de63fa9d283a337aabeb1
Author: Atzm Watanabe <atzm@stratosphere.co.jp>
vxlan: Allow setting destination to unicast address.
Since this commit has not made it upstream (still net-next),
and better to avoid gratitious changes to exported API's;
go back to original definition, and add a comment.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NDA_PORT attribute was added, but the author wasn't careful
about width (port is 16 bits), or byte order. The attribute was
being dumped as 16 bits, but only 32 bit value would be accepted
when setting up a device. Also, the remote port is in network
byte order and was being compared with default port in host byte
order.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default port for VXLAN is not same as IANA value.
Document this.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
