| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 5e1663810e11c64956aa7e280cf74b2f3284d816 ]
The TDC is currently hardcoded enabled. This means that even for lower
CAN-FD data bitrates (with a DBRP (data bitrate prescaler) > 2) a TDC
is configured. This leads to a bus-off condition.
ISO 11898-1 section 11.3.3 says "Transmitter delay compensation" (TDC)
is only applicable if DBRP is 1 or 2.
To fix the problem, switch the driver to use the TDC calculation
provided by the CAN driver framework (which respects ISO 11898-1
section 11.3.3). This has the positive side effect that userspace can
control TDC as needed.
Demonstration of the feature in action:
| $ ip link set can0 up type can bitrate 125000 dbitrate 500000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 125000 sample-point 0.875
| tq 50 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 10 brp 2
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 500000 dsample-point 0.875
| dtq 125 dprop-seg 6 dphase-seg1 7 dphase-seg2 2 dsjw 1 dbrp 5
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
| $ ip link set can0 up type can bitrate 1000000 dbitrate 4000000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD,TDC-AUTO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 1000000 sample-point 0.750
| tq 25 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 5 brp 1
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 4000000 dsample-point 0.700
| dtq 25 dprop-seg 3 dphase-seg1 3 dphase-seg2 3 dsjw 1 dbrp 1
| tdco 7
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
There has been some confusion about the MCP2518FD using a relative or
absolute TDCO due to the datasheet specifying a range of [-64,63]. I
have a custom board with a 40 MHz clock and an estimated loop delay of
100 to 216 ns. During testing at a data bit rate of 4 Mbit/s I found
that using can_get_relative_tdco() resulted in bus-off errors. The
final TDCO value was 1 which corresponds to a 10% SSP in an absolute
configuration. This behavior is expected if the TDCO value is really
absolute and not relative. Using priv->can.tdc.tdco instead results in
a final TDCO of 8, setting the SSP at exactly 80%. This configuration
works.
The automatic, manual, and off TDC modes were tested at speeds up to,
and including, 8 Mbit/s on real hardware and behave as expected.
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Kelsey Maes <kelsey@vpprocess.com>
Closes: https://lore.kernel.org/all/C2121586-C87F-4B23-A933-845362C29CA1@vpprocess.com
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Kelsey Maes <kelsey@vpprocess.com>
Link: https://patch.msgid.link/20250430161501.79370-1-kelsey@vpprocess.com
[mkl: add comment]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dcaeeb8ae84c5506ebc574732838264f3887738c ]
The spin lock tx_handling_spinlock in struct m_can_classdev is not
being initialized. This leads the following spinlock bad magic
complaint from the kernel, eg. when trying to send CAN frames with
cansend from can-utils:
| BUG: spinlock bad magic on CPU#0, cansend/95
| lock: 0xff60000002ec1010, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
| CPU: 0 UID: 0 PID: 95 Comm: cansend Not tainted 6.15.0-rc3-00032-ga79be02bba5c #5 NONE
| Hardware name: MachineWare SIM-V (DT)
| Call Trace:
| [<ffffffff800133e0>] dump_backtrace+0x1c/0x24
| [<ffffffff800022f2>] show_stack+0x28/0x34
| [<ffffffff8000de3e>] dump_stack_lvl+0x4a/0x68
| [<ffffffff8000de70>] dump_stack+0x14/0x1c
| [<ffffffff80003134>] spin_dump+0x62/0x6e
| [<ffffffff800883ba>] do_raw_spin_lock+0xd0/0x142
| [<ffffffff807a6fcc>] _raw_spin_lock_irqsave+0x20/0x2c
| [<ffffffff80536dba>] m_can_start_xmit+0x90/0x34a
| [<ffffffff806148b0>] dev_hard_start_xmit+0xa6/0xee
| [<ffffffff8065b730>] sch_direct_xmit+0x114/0x292
| [<ffffffff80614e2a>] __dev_queue_xmit+0x3b0/0xaa8
| [<ffffffff8073b8fa>] can_send+0xc6/0x242
| [<ffffffff8073d1c0>] raw_sendmsg+0x1a8/0x36c
| [<ffffffff805ebf06>] sock_write_iter+0x9a/0xee
| [<ffffffff801d06ea>] vfs_write+0x184/0x3a6
| [<ffffffff801d0a88>] ksys_write+0xa0/0xc0
| [<ffffffff801d0abc>] __riscv_sys_write+0x14/0x1c
| [<ffffffff8079ebf8>] do_trap_ecall_u+0x168/0x212
| [<ffffffff807a830a>] handle_exception+0x146/0x152
Initializing the spin lock in m_can_class_allocate_dev solves that
problem.
Fixes: 1fa80e23c150 ("can: m_can: Introduce a tx_fifo_in_flight counter")
Signed-off-by: Antonios Salios <antonios@mwa.re>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250425111744.37604-2-antonios@mwa.re
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8716b5b0dff1b3d523b4a83fd5e94d57b887c5c ]
Remove redundant PSE reset.
When setting FE register there is no need to reset PSE,
doing so may cause FE to work abnormal.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/3a5223473e086a4b54a2b9a44df7d9ddcc2bc75a
Fixes: dee4dd10c79aa ("net: ethernet: mtk_eth_soc: ppe: add support for multiple PPEs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://patch.msgid.link/18f0ac7d83f82defa3342c11ef0d1362f6b81e88.1746406763.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4db6c75124d871fbabf8243f947d34cc7e0697fc ]
The purpose of resetting the TX queue is to reset the byte and packet
count as well as to clear the software flow control XOFF bit.
MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.
Packets may stop being sent after reset and "transmit timeout" log may
be displayed.
Import fix from MediaTek's SDK to resolve this issue.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/319c0d9905579a46dc448579f892f364f1f84818
Fixes: f63959c7eec31 ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/c9ff9adceac4f152239a0f65c397f13547639175.1746406763.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4397684a292a71fbc1e815c3e283f7490ddce5ae ]
The selftests added to our CI by Bui Quang Minh recently reveals
that there is a mem leak on the error path of virtnet_xsk_pool_enable():
unreferenced object 0xffff88800a68a000 (size 2048):
comm "xdp_helper", pid 318, jiffies 4294692778
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 0):
__kvmalloc_node_noprof+0x402/0x570
virtnet_xsk_pool_enable+0x293/0x6a0 (drivers/net/virtio_net.c:5882)
xp_assign_dev+0x369/0x670 (net/xdp/xsk_buff_pool.c:226)
xsk_bind+0x6a5/0x1ae0
__sys_bind+0x15e/0x230
__x64_sys_bind+0x72/0xb0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Acked-by: Jason Wang <jasowang@redhat.com>
Fixes: e9f3962441c0 ("virtio_net: xsk: rx: support fill with xsk buffer")
Link: https://patch.msgid.link/20250430163836.3029761-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 21a4e3ce6dc7b0a3bc882ebe1cb921a40235ddb0 ]
This patch implement the logic of bind/unbind xsk pool to sq and rq.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20241112012928.102478-10-xuanzhuo@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 4397684a292a ("virtio-net: free xsk_buffs on error in virtnet_xsk_pool_enable()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 037ada7a3181300218e4fd78bef6a741cfa7f808 upstream.
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-2-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84f5eb833f53ae192baed4cfb8d9eaab43481fc9 upstream.
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
With the mcp251xfd driver the removal of the module causes the
following warning:
| WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8
as can_rx_offload_del() deletes the NAPI, while it is still active,
because the interface is still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-1-59a9b131589d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0713a1b3276b98c7dafbeefef00d7bc3a9119a84 upstream.
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 1be37d3b0414 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-3-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ee512922ddd7d64afe2b28830a88f19063217649 ]
In case the CMD_RTS got corrupted by interferences, the MSE102x
doesn't allow a retransmission of the command. Instead the Ethernet
frame must be shifted out of the SPI FIFO. Since the actual length is
unknown, assume the maximum possible value.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-5-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d4dda902dac194e3231a1ed0f76c6c3b6340ba8a ]
Since there is no protection in the SPI protocol against electrical
interferences, the driver shouldn't blindly trust the length payload
of CMD_RTS. So introduce a bounds check for incoming frames.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74987089ec678b4018dba0a609e9f4bf6ef7f4ad ]
The LEN_MASK for CMD_RTS doesn't cover the whole parameter mask.
The Bit 11 is reserved, so adjust LEN_MASK accordingly.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 55f362885951b2d00fd7fbb02ef0227deea572c2 ]
The MSE102x doesn't provide any SPI commands for interrupt handling.
So in case the interrupt fired before the driver requests the IRQ,
the interrupt will never fire again. In order to fix this always poll
for pending packets after opening the interface.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4971394d9d624f91689d766f31ce668d169d9959 ]
Currently the ptp_clock_register() is called before relative
ptp resource ready. It may cause unexpected result when upper
layer called the ptp API during the timewindow. Fix it by
moving the ptp_clock_register() to the function end.
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250430093052.2400464-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e317aebeefcb3b0c71f2305af3c22871ca6b3833 ]
The size of the tm_qset file of debugfs is limited to 64 KB,
which is too small in the scenario with 1280 qsets.
The size needs to be expanded to 1 MB.
Fixes: 5e69ea7ee2a6 ("net: hns3: refactor the debugfs process")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8e6b9c6ea5a55045eed6526d8ee49e93192d1a58 ]
When a VF is passthrough to a VM, and the VM is killed, the reported
interrupt may not been handled, it will remain, and won't be clear by
the nic engine even with a flr or tqp reset. When the VM restart, the
interrupt of the first vector may be dropped by the second enable_irq
in vfio, see the issue below:
https://gitlab.com/qemu-project/qemu/-/issues/2884#note_2423361621
We notice that the vfio has always behaved this way, and the interrupt
is a residue of the nic engine, so we fix the problem by moving the
vector enable process out of the enable_irq loop.
Fixes: 08a100689d4b ("net: hns3: re-organize vector handle")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ef2383d078edcbe3055032436b16cdf206f26de2 ]
The VF driver missed to store the rx VLAN tag strip state when
user change the rx VLAN tag offload state. And it will default
to enable the rx vlan tag strip when re-init VF device after
reset. So if user disable rx VLAN tag offload, and trig reset,
then the HW will still strip the VLAN tag from packet nad fill
into RX BD, but the VF driver will ignore it for rx VLAN tag
offload disabled. It may cause the rx VLAN tag dropped.
Fixes: b2641e2ad456 ("net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250430093052.2400464-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 34f42736b325287a7b2ce37e415838f539767bda ]
When the host loses heartbeat messages from the device,
the driver calls the device-specific ndo_stop function,
which frees the resources. If the driver is unloaded in
this scenario, it calls ndo_stop again, attempting to free
resources that have already been freed, leading to a host
hang issue. To resolve this, dev_close should be called
instead of the device-specific stop function.dev_close
internally calls ndo_stop to stop the network interface
and performs additional cleanup tasks. During the driver
unload process, if the device is already down, ndo_stop
is not called.
Fixes: 5cb96c29aa0e ("octeon_ep: add heartbeat monitor")
Signed-off-by: Sathesh B Edara <sedara@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250429114624.19104-1-sedara@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a179aad12badc43201cbf45d1e8ed2c1383c76b9 ]
Activate TX hang workaround also in
fec_enet_txq_submit_skb() when TSO is not enabled.
Errata: ERR007885
Symptoms: NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
commit 37d6017b84f7 ("net: fec: Workaround for imx6sx enet tx hang when enable three queues")
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
Fixes: 53bb20d1faba ("net: fec: add variable reg_desc_active to speed things up")
Signed-off-by: Mattias Barthel <mattias.barthel@atlascopco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250429090826.3101258-1-mattiasbarthel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2d52e2e38b85c8b7bc00dca55c2499f46f8c8198 ]
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 927069d5c40c1cfa7b2d13cfc6d7d58bc6f85c50 ]
Recent updates to the PTP part of bnxt changed the way PTP FIFO is
cleared, skbs waiting for TX timestamps are now cleared during
ndo_close() call. To do clearing procedure, the ptp structure must
exist and point to a valid address. Module destroy sequence had ptp
clear code running before netdev close causing invalid memory access and
kernel crash. Change the sequence to destroy ptp structure after device
close.
Fixes: 8f7ae5a85137 ("bnxt_en: improve TX timestamping FIFO configuration")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Closes: https://lore.kernel.org/netdev/CAMArcTWDe2cd41=ub=zzvYifaYcYv-N-csxfqxUvejy_L0D6UQ@mail.gmail.com/
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250430170343.759126-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02e8be5a032cae0f4ca33c6053c44d83cf4acc93 ]
For version 1 register dump that includes the PCIe stats, the existing
code incorrectly assumes that all PCIe stats are 64-bit values. Fix it
by using an array containing the starting and ending index of the 32-bit
values. The loop in bnxt_get_regs() will use the array to do proper
endian swap for the 32-bit values.
Fixes: b5d600b027eb ("bnxt_en: Add support for 'ethtool -d'")
Reviewed-by: Shruti Parab <shruti.parab@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b87bd94f34370bbf1dfa59352bed8efab5bf419 ]
When retrieving the FW coredump using ethtool, it can sometimes cause
memory corruption:
BUG: KFENCE: memory corruption in __bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
Corrupted memory at 0x000000008f0f30e8 [ ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ] (in kfence-#45):
__bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
ethtool_get_dump_data+0xdc/0x1a0
__dev_ethtool+0xa1e/0x1af0
dev_ethtool+0xa8/0x170
dev_ioctl+0x1b5/0x580
sock_do_ioctl+0xab/0xf0
sock_ioctl+0x1ce/0x2e0
__x64_sys_ioctl+0x87/0xc0
do_syscall_64+0x5c/0xf0
entry_SYSCALL_64_after_hwframe+0x78/0x80
...
This happens when copying the coredump segment list in
bnxt_hwrm_dbg_dma_data() with the HWRM_DBG_COREDUMP_LIST FW command.
The info->dest_buf buffer is allocated based on the number of coredump
segments returned by the FW. The segment list is then DMA'ed by
the FW and the length of the DMA is returned by FW. The driver then
copies this DMA'ed segment list to info->dest_buf.
In some cases, this DMA length may exceed the info->dest_buf length
and cause the above BUG condition. Fix it by capping the copy
length to not exceed the length of info->dest_buf. The extra
DMA data contains no useful information.
This code path is shared for the HWRM_DBG_COREDUMP_LIST and the
HWRM_DBG_COREDUMP_RETRIEVE FW commands. The buffering is different
for these 2 FW commands. To simplify the logic, we need to move
the line to adjust the buffer length for HWRM_DBG_COREDUMP_RETRIEVE
up, so that the new check to cap the copy length will work for both
commands.
Fixes: c74751f4c392 ("bnxt_en: Return error if FW returns more data than dump length")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea9376cf68230e05492f22ca45d329f16e262c7b ]
When handling HWRM_DBG_COREDUMP_LIST FW command in
bnxt_hwrm_dbg_dma_data(), the allocated buffer info->dest_buf is
not freed in the error path. In the normal path, info->dest_buf
is assigned to coredump->data and it will eventually be freed after
the coredump is collected.
Free info->dest_buf immediately inside bnxt_hwrm_dbg_dma_data() in
the error path.
Fixes: c74751f4c392 ("bnxt_en: Return error if FW returns more data than dump length")
Reported-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1ae04e489dd757e1e61999362f33e7c554c3b9e3 ]
On some architectures (e.g. ARM), calling pci_alloc_irq_vectors()
will immediately cause the MSIX table to be written. This will not
work if we haven't called bnxt_reserve_rings() to properly map
the MSIX table to the MSIX vectors reserved by FW.
Fix the FW error recovery path to delay the bnxt_init_int_mode() ->
pci_alloc_irq_vectors() call by removing it from bnxt_hwrm_if_change().
bnxt_request_irq() later in the code path will call it and by then the
MSIX table is properly mapped.
Fixes: 4343838ca5eb ("bnxt_en: Replace deprecated PCI MSIX APIs")
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a63db07e4ecd45b027718168faf7d798bb47bf58 ]
If bnxt_rx_vlan() fails because the VLAN protocol ID is invalid,
the SKB is freed but we're missing the call to recycle it. This
may cause the warning:
"page_pool_release_retry() stalled pool shutdown"
Add the missing skb_mark_for_recycle() in bnxt_rx_vlan().
Fixes: 86b05508f775 ("bnxt_en: Use the unified RX page pool buffers for XDP and non-XDP")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8e6cc9045380f3f0c48ebda2bda5e1abe263388d ]
When RDMA driver is loaded, running offline self test is not
supported and driver returns failure early. But it is not clearing
the input buffer and hence the application prints some junk
characters for individual test results.
Fix it by clearing the buffer before returning.
Fixes: 895621f1c816 ("bnxt_en: Don't support offline self test when RoCE driver is loaded")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9ab7a709c926c16b4433cf02d04fcbcf35aaab2b ]
WARN_ON() is triggered in __flush_work() if bnxt_init_chip() fails
because we call cancel_work_sync() on dim work that has not been
initialized.
WARNING: CPU: 37 PID: 5223 at kernel/workqueue.c:4201 __flush_work.isra.0+0x212/0x230
The driver relies on the BNXT_STATE_NAPI_DISABLED bit to check if dim
work has already been cancelled. But in the bnxt_open() path,
BNXT_STATE_NAPI_DISABLED is not set and this causes the error
path to think that it needs to cancel the uninitalized dim work.
Fix it by setting BNXT_STATE_NAPI_DISABLED during initialization.
The bit will be cleared when we enable NAPI and initialize dim work.
Fixes: 40452969a506 ("bnxt_en: Fix DIM shutdown")
Suggested-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Shravya KN <shravya.k-n@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 426d487bca38b34f39c483edfc6313a036446b33 ]
Simplest setup to reproduce the issue: connect 2 ports of the
LS1028A-RDB together (eno0 with swp0) and run:
$ ip link set eno0 up && ip link set swp0 up
$ tc qdisc replace dev swp0 parent root handle 100 taprio num_tc 8 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 map 0 1 2 3 4 5 6 7 \
base-time 0 sched-entry S 20 300000 sched-entry S 10 200000 \
sched-entry S 20 300000 sched-entry S 48 200000 \
sched-entry S 20 300000 sched-entry S 83 200000 \
sched-entry S 40 300000 sched-entry S 00 200000 flags 2
$ ptp4l -i eno0 -f /etc/linuxptp/configs/gPTP.cfg -m &
$ ptp4l -i swp0 -f /etc/linuxptp/configs/gPTP.cfg -m
One will observe that the PTP state machine on swp0 starts
synchronizing, then it attempts to do a clock step, and after that, it
never fails to recover from the condition below.
ptp4l[82.427]: selected best master clock 00049f.fffe.05f627
ptp4l[82.428]: port 1 (swp0): MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[83.252]: port 1 (swp0): UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[83.886]: rms 4537731277 max 9075462553 freq -18518 +/- 11467 delay 818 +/- 0
ptp4l[84.170]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[85.304]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[85.305]: port 1 (swp0): send peer delay response failed
ptp4l[85.306]: port 1 (swp0): clearing fault immediately
ptp4l[86.304]: timed out while polling for tx timestamp
A hint is given by the non-zero statistics for dropped packets which
were expecting hardware TX timestamps:
$ ethtool --include-statistics -T swp0
(...)
Statistics:
tx_pkts: 30
tx_lost: 11
tx_err: 0
We know that when PTP clock stepping takes place (from ocelot_ptp_settime64()
or from ocelot_ptp_adjtime()), vsc9959_tas_clock_adjust() is called.
Another interesting hint is that placing an early return in
vsc9959_tas_clock_adjust(), so as to neutralize this function, fixes the
issue and TX timestamps are no longer dropped.
The debugging function written by me and included below is intended to
read the GCL RAM, after the admin schedule became operational, through
the two status registers available for this purpose:
QSYS_GCL_STATUS_REG_1 and QSYS_GCL_STATUS_REG_2.
static void vsc9959_print_tas_gcl(struct ocelot *ocelot)
{
u32 val, list_length, interval, gate_state;
int i, err;
err = read_poll_timeout(ocelot_read, val,
!(val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING),
10, 100000, false, ocelot, QSYS_PARAM_STATUS_REG_8);
if (err) {
dev_err(ocelot->dev,
"Failed to wait for TAS config pending bit to clear: %pe\n",
ERR_PTR(err));
return;
}
val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_3);
list_length = QSYS_PARAM_STATUS_REG_3_LIST_LENGTH_X(val);
dev_info(ocelot->dev, "GCL length: %u\n", list_length);
for (i = 0; i < list_length; i++) {
ocelot_rmw(ocelot,
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM(i),
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM_M,
QSYS_GCL_STATUS_REG_1);
interval = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_2);
val = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_1);
gate_state = QSYS_GCL_STATUS_REG_1_GATE_STATE_X(val);
dev_info(ocelot->dev, "GCL entry %d: states 0x%x interval %u\n",
i, gate_state, interval);
}
}
Calling it from two places: after the initial QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
performed by vsc9959_qos_port_tas_set(), and after the one done by
vsc9959_tas_clock_adjust(), I notice the following difference.
From the tc-taprio process context, where the schedule was initially
configured, the GCL looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 1: states 0x10 interval 200000
mscc_felix 0000:00:00.5: GCL entry 2: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 3: states 0x48 interval 200000
mscc_felix 0000:00:00.5: GCL entry 4: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 5: states 0x83 interval 200000
mscc_felix 0000:00:00.5: GCL entry 6: states 0x40 interval 300000
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 200000
But from the ptp4l clock stepping process context, when the
vsc9959_tas_clock_adjust() hook is called, the GCL RAM of the
operational schedule now looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 1: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 2: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 3: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 4: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 5: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 6: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 0
I do not have a formal explanation, just experimental conclusions.
It appears that after triggering QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
for a port's TAS, the GCL entry RAM is updated anyway, despite what the
documentation claims: "Specify the time interval in
QSYS::GCL_CFG_REG_2.TIME_INTERVAL. This triggers the actual RAM
write with the gate state and the time interval for the entry number
specified". We don't touch that register (through vsc9959_tas_gcl_set())
from vsc9959_tas_clock_adjust(), yet the GCL RAM is updated anyway.
It seems to be updated with effectively stale memory, which in my
testing can hold a variety of things, including even pieces of the
previously applied schedule, for particular schedule lengths.
As such, in most circumstances it is very difficult to pinpoint this
issue, because the newly updated schedule would "behave strangely",
but ultimately might still pass traffic to some extent, due to some
gate entries still being present in the stale GCL entry RAM. It is easy
to miss.
With the particular schedule given at the beginning, the GCL RAM
"happens" to be reproducibly rewritten with all zeroes, and this is
consistent with what we see: when the time-aware shaper has gate entries
with all gates closed, traffic is dropped on TX, no wonder we can't
retrieve TX timestamps.
Rewriting the GCL entry RAM when reapplying the new base time fixes the
observed issue.
Fixes: 8670dc33f48b ("net: dsa: felix: update base time of time-aware shaper when adjusting PTP time")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e0490fc36cdac696f96e57b61d93b9ae32e0f4c ]
If the mtk_poll_rx() function detects the MTK_RESETTING flag, it will
jump to release_desc and refill the high word of the SDP on the 4GB RFB.
Subsequently, mtk_rx_clean will process an incorrect SDP, leading to a
panic.
Add patch from MediaTek's SDK to resolve this.
Fixes: 2d75891ebc09 ("net: ethernet: mtk_eth_soc: support 36-bit DMA addressing on MT7988")
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/71f47ea785699c6aa3b922d66c2bdc1a43da25b1
Signed-off-by: Chad Monroe <chad@monroe.io>
Link: https://patch.msgid.link/4adc2aaeb0fb1b9cdc56bf21cf8e7fa328daa345.1745715843.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c7d6cb96d5c33b5148f3dc76fcd30a9b8cd9e973 ]
Commit 1a931c4f5e68 ("igc: add lock preventing multiple simultaneous PTM
transactions") added a new mutex to protect concurrent PTM transactions.
This lock is acquired in igc_ptp_reset() in order to ensure the PTM
registers are properly disabled after a device reset.
The flow where the lock is acquired already holds a spinlock, so acquiring
a mutex leads to a sleep-while-locking bug, reported both by smatch,
and the kernel test robot.
The critical section in igc_ptp_reset() does correctly use the
readx_poll_timeout_atomic variants, but the standard PTM flow uses regular
sleeping variants. This makes converting the mutex to a spinlock a bit
tricky.
Instead, re-order the locking in igc_ptp_reset. Acquire the mutex first,
and then the tmreg_lock spinlock. This is safe because there is no other
ordering dependency on these locks, as this is the only place where both
locks were acquired simultaneously. Indeed, any other flow acquiring locks
in that order would be wrong regardless.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Fixes: 1a931c4f5e68 ("igc: add lock preventing multiple simultaneous PTM transactions")
Link: https://lore.kernel.org/intel-wired-lan/Z_-P-Hc1yxcw0lTB@stanley.mountain/
Link: https://lore.kernel.org/intel-wired-lan/202504211511.f7738f5d-lkp@intel.com/T/#u
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ed375b182140eeb9c73609b17939c8a29b27489e ]
Before the referenced commit, the shutdown just called idpf_remove(),
this way IDPF_REMOVE_IN_PROG was protecting us from the serv_task
rescheduling reset. Without this flag set the shutdown process is
vulnerable to HW reset or any other triggering conditions (such as
default mailbox being destroyed).
When one of conditions checked in idpf_service_task becomes true,
vc_event_task can be rescheduled during shutdown, this leads to accessing
freed memory e.g. idpf_req_rel_vector_indexes() trying to read
vport->q_vector_idxs. This in turn causes the system to become defunct
during e.g. systemctl kexec.
Considering using IDPF_REMOVE_IN_PROG would lead to more heavy shutdown
process, instead just cancel the serv_task before cancelling
adapter->serv_task before cancelling adapter->vc_event_task to ensure that
reset will not be scheduled while we are doing a shutdown.
Fixes: 4c9106f4906a ("idpf: fix adapter NULL pointer dereference on reboot")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a558cbda51bef09773c72bf74a32047479110c7 ]
In case of failing on rss_data->rss_key allocation the function is
freeing vport without freeing earlier allocated q_vector_idxs. Fix it.
Move from freeing in error branch to goto scheme.
Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport")
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Suggested-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b23285e93bef729e67519a5209d5b7fde3b4af50 ]
This bit is necessary to receive packets from the internal PHY.
Without this bit set, no activity occurs on the interface.
Normally u-boot sets this bit, but if u-boot is compiled without
net support, the interface will be up but without any activity.
If bit is set once, it will work until the IP is powered down or reset.
The vendor SDK sets this bit along with the PHY_ID bits.
Signed-off-by: Da Xue <da@libre.computer>
Fixes: 9a24e1ff4326 ("net: mdio: add amlogic gxl mdio mux support")
Link: https://patch.msgid.link/20250425192009.1439508-1-da@libre.computer
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e7e5ae71831c44d58627a991e603845a2fed2cab ]
As it's name suggests, parse_eeprom() parses EEPROM data.
This is done by reading data, 16 bits at a time as follows:
for (i = 0; i < 128; i++)
((__le16 *) sromdata)[i] = cpu_to_le16(read_eeprom(np, i));
sromdata is at the same memory location as psrom.
And the type of psrom is a pointer to struct t_SROM.
As can be seen in the loop above, data is stored in sromdata, and thus psrom,
as 16-bit little-endian values.
However, the integer fields of t_SROM are host byte order integers.
And in the case of led_mode this leads to a little endian value
being incorrectly treated as host byte order.
Looking at rio_set_led_mode, this does appear to be a bug as that code
masks led_mode with 0x1, 0x2 and 0x8. Logic that would be effected by a
reversed byte order.
This problem would only manifest on big endian hosts.
Found by inspection while investigating a sparse warning
regarding the crc field of t_SROM.
I believe that warning is a false positive. And although I plan
to send a follow-up to use little-endian types for other the integer
fields of PSROM_t I do not believe that will involve any bug fixes.
Compile tested only.
Fixes: c3f45d322cbd ("dl2k: Add support for IP1000A-based cards")
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250425-dlink-led-mode-v1-1-6bae3c36e736@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 713dd6c2deca88cba0596b1e2576f7b7a8e5c59e ]
Split offloads into csum, tso and other offloads so that tunneled
packets do not by default have all the offloads enabled.
Stateless offloads for encapsulated packets are not yet supported in
firmware/software but in the driver we were setting the features same as
non encapsulated features.
Fixed naming to clarify CSUM bits are being checked for Tx.
Inherit netdev features to VLAN interfaces as well.
Fixes: 0fe45467a104 ("idpf: add create vport and netdev configuration")
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Zachary Goldstein <zachmgoldstein@google.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250425222636.3188441-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 425c5f266b2edeee0ce16fedd8466410cdcfcfe3 ]
As mentioned in the commit baeb705fd6a7 ("ice: always check VF VSI
pointer values"), we need to perform a null pointer check on the return
value of ice_get_vf_vsi() before using it.
Fixes: 6ebbe97a4881 ("ice: Add a per-VF limit on number of FDIR filters")
Signed-off-by: Xuanqiang Luo <luoxuanqiang@kylinos.cn>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250425222636.3188441-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dfd76010f8e821b66116dec3c7d90dd2403d1396 ]
A use-after-free error popped up in stress testing:
[Mon Apr 21 21:21:33 2025] BUG: KFENCE: use-after-free write in pdsc_auxbus_dev_del+0xef/0x160 [pds_core]
[Mon Apr 21 21:21:33 2025] Use-after-free write at 0x000000007013ecd1 (in kfence-#47):
[Mon Apr 21 21:21:33 2025] pdsc_auxbus_dev_del+0xef/0x160 [pds_core]
[Mon Apr 21 21:21:33 2025] pdsc_remove+0xc0/0x1b0 [pds_core]
[Mon Apr 21 21:21:33 2025] pci_device_remove+0x24/0x70
[Mon Apr 21 21:21:33 2025] device_release_driver_internal+0x11f/0x180
[Mon Apr 21 21:21:33 2025] driver_detach+0x45/0x80
[Mon Apr 21 21:21:33 2025] bus_remove_driver+0x83/0xe0
[Mon Apr 21 21:21:33 2025] pci_unregister_driver+0x1a/0x80
The actual device uninit usually happens on a separate thread
scheduled after this code runs, but there is no guarantee of order
of thread execution, so this could be a problem. There's no
actual need to clear the client_id at this point, so simply
remove the offending code.
Fixes: 10659034c622 ("pds_core: add the aux client API")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250425203857.71547-1-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b699bdc720c0255d1bb76cecba7382c1f2107af5 ]
In preparation for adding a new auxiliary_device for the PF,
make the vif type an argument to pdsc_auxbus_dev_add(). Pass in
the address of the padev pointer so that the caller can specify
where to save it and keep the mutex usage within the function.
Link: https://patch.msgid.link/r/20250320194412.67983-3-shannon.nelson@amd.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: dfd76010f8e8 ("pds_core: remove write-after-free of client_id")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8562da829432d04a0de1830146984c89844f35e ]
Since there really is no useful return, advertising a return value
is rather misleading. Make pdsc_auxbus_dev_del() a void function.
Link: https://patch.msgid.link/r/20250320194412.67983-2-shannon.nelson@amd.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: dfd76010f8e8 ("pds_core: remove write-after-free of client_id")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c47d5753a119f1c986bc3ed92e9178d2624e1e8 ]
When removing the clock bits for clocks which aren't used by the
Ethernet driver their names should also have been removed from the
mtk_clks_source_name array.
Remove them now as enum mtk_clks_map needs to match the
mtk_clks_source_name array so the driver can make sure that all required
clocks are present and correctly name missing clocks.
Fixes: 887b1d1adb2e ("net: ethernet: mtk_eth_soc: drop clocks unused by Ethernet driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/d075e706ff1cebc07f9ec666736d0b32782fd487.1745555321.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e54b4db35e201a9173da9cb7abc8377e12abaf87 ]
In mtk_star_rx_poll function, on event processing completion, the
mtk_star_emac driver calls napi_complete_done but ignores its return
code and enable RX DMA interrupts inconditionally. This return code
gives the info if a device should avoid rearming its interrupts or not,
so fix this behaviour by taking it into account.
Fixes: 8c7bd5a454ff ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250424-mtk_star_emac-fix-spinlock-recursion-issue-v2-2-f3fde2e529d8@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6fe0866014486736cc3ba1c6fd4606d3dbe55c9c ]
Use spin_lock_irqsave and spin_unlock_irqrestore instead of spin_lock
and spin_unlock in mtk_star_emac driver to avoid spinlock recursion
occurrence that can happen when enabling the DMA interrupts again in
rx/tx poll.
```
BUG: spinlock recursion on CPU#0, swapper/0/0
lock: 0xffff00000db9cf20, .magic: dead4ead, .owner: swapper/0/0,
.owner_cpu: 0
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted
6.15.0-rc2-next-20250417-00001-gf6a27738686c-dirty #28 PREEMPT
Hardware name: MediaTek MT8365 Open Platform EVK (DT)
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x60/0x80
dump_stack+0x18/0x24
spin_dump+0x78/0x88
do_raw_spin_lock+0x11c/0x120
_raw_spin_lock+0x20/0x2c
mtk_star_handle_irq+0xc0/0x22c [mtk_star_emac]
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x4c/0xb0
handle_fasteoi_irq+0xa0/0x1bc
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x120
do_interrupt_handler+0x50/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
regmap_mmio_read32le+0xc/0x20 (P)
_regmap_bus_reg_read+0x6c/0xac
_regmap_read+0x60/0xdc
regmap_read+0x4c/0x80
mtk_star_rx_poll+0x2f4/0x39c [mtk_star_emac]
__napi_poll+0x38/0x188
net_rx_action+0x164/0x2c0
handle_softirqs+0x100/0x244
__do_softirq+0x14/0x20
____do_softirq+0x10/0x20
call_on_irq_stack+0x24/0x64
do_softirq_own_stack+0x1c/0x40
__irq_exit_rcu+0xd4/0x10c
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x38/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
cpuidle_enter_state+0xac/0x320 (P)
cpuidle_enter+0x38/0x50
do_idle+0x1e4/0x260
cpu_startup_entry+0x34/0x3c
rest_init+0xdc/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
```
Fixes: 0a8bd81fd6aa ("net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250424-mtk_star_emac-fix-spinlock-recursion-issue-v2-1-f3fde2e529d8@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
rtase_calc_time_mitigation
[ Upstream commit 68f9d8974b545668e1be2422240b25a92e304b14 ]
Fix the following compile error reported by the kernel test
robot by modifying the condition used to detect overflow in
rtase_calc_time_mitigation.
In file included from include/linux/mdio.h:10:0,
from drivers/net/ethernet/realtek/rtase/rtase_main.c:58:
In function 'u16_encode_bits',
inlined from 'rtase_calc_time_mitigation.constprop' at drivers/net/
ethernet/realtek/rtase/rtase_main.c:1915:13,
inlined from 'rtase_init_software_variable.isra.41' at drivers/net/
ethernet/realtek/rtase/rtase_main.c:1961:13,
inlined from 'rtase_init_one' at drivers/net/ethernet/realtek/
rtase/rtase_main.c:2111:2:
>> include/linux/bitfield.h:178:3: error: call to '__field_overflow'
declared with attribute error: value doesn't fit into mask
__field_overflow(); \
^~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:198:2: note: in expansion of macro
'____MAKE_OP'
____MAKE_OP(u##size,u##size,,)
^~~~~~~~~~~
include/linux/bitfield.h:200:1: note: in expansion of macro
'__MAKE_OP'
__MAKE_OP(16)
^~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503182158.nkAlbJWX-lkp@intel.com/
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250424040444.5530-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8f7ae5a85137b913cb97e2d24409d36548d0bab1 ]
Reconfiguration of netdev may trigger close/open procedure which can
break FIFO status by adjusting the amount of empty slots for TX
timestamps. But it is not really needed because timestamps for the
packets sent over the wire still can be retrieved. On the other side,
during netdev close procedure any skbs waiting for TX timestamps can be
leaked because there is no cleaning procedure called. Free skbs waiting
for TX timestamps when closing netdev.
Fixes: 8aa2a79e9b95 ("bnxt_en: Increase the max total outstanding PTP TX packets to 4")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Link: https://patch.msgid.link/20250424125547.460632-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8548c84c004be3da4ffbe35ed0589041a4050c03 ]
The netdevice usage count increases during transmit queue timeouts
because netdev_hold is called in ndo_tx_timeout, scheduling a task
to reinitialize the card. Although netdev_put is called at the end
of the scheduled work, rtnl_unlock checks the reference count during
cleanup. This could cause issues if transmit timeout is called on
multiple queues.
Fixes: cb7dd712189f ("octeon_ep_vf: Add driver framework and device initialization")
Signed-off-by: Sathesh B Edara <sedara@marvell.com>
Link: https://patch.msgid.link/20250424133944.28128-1-sedara@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5ec6d7d737a491256cd37e33910f7ac1978db591 ]
The following set of commands:
ip link add br0 type bridge vlan_filtering 1 # vlan_default_pvid 1 is implicit
ip link set swp0 master br0
bridge vlan add dev swp0 vid 1
should result in the dropping of untagged and 802.1p-tagged traffic, but
we see that it continues to be accepted. Whereas, had we deleted VID 1
instead, the aforementioned dropping would have worked
This is because the ANA_PORT_DROP_CFG update logic doesn't run, because
ocelot_vlan_add() only calls ocelot_port_set_pvid() if the new VLAN has
the BRIDGE_VLAN_INFO_PVID flag.
Similar to other drivers like mt7530_port_vlan_add() which handle this
case correctly, we need to test whether the VLAN we're changing used to
have the BRIDGE_VLAN_INFO_PVID flag, but lost it now. That amounts to a
PVID deletion and should be treated as such.
Regarding blame attribution: this never worked properly since the
introduction of bridge VLAN filtering in commit 7142529f1688 ("net:
mscc: ocelot: add VLAN filtering"). However, there was a significant
paradigm shift which aligned the ANA_PORT_DROP_CFG register with the
PVID concept rather than with the native VLAN concept, and that change
wasn't targeted for 'stable'. Realistically, that is as far as this fix
needs to be propagated to.
Fixes: be0576fed6d3 ("net: mscc: ocelot: move the logic to drop 802.1p traffic to the pvid deletion")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250424223734.3096202-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 90538d23278a981e344d364e923162fce752afeb ]
The cited commit assumes enabling roce always succeeds. But it is
not true. Add error handling for it.
Fixes: 80f09dfc237f ("net/mlx5: Eswitch, enable RoCE loopback traffic")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250423083611.324567-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c2940ec0ddf51c689ee9ab85ead85c11b77809d ]
RTNL needs to be acquired before state_lock.
Fixes: fdce06bda7e5 ("net/mlx5e: Acquire RTNL lock before RQs/SQs activation/deactivation")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250423083611.324567-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 172c034264c894518c012387f2de2f9d6443505d ]
Previously the offload of the rule with header rewrite and mirror to
both internal and external destinations is skipped if the encap entry
is not valid. But it shouldn't because driver will try to offload it
again if neighbor is updated and encap entry is valid, to replace the
old FTE added for slow path. But the extra split attr doesn't exist at
that time as the process is skipped, driver then fails to offload it.
To fix this issue, remove the checking and continue the attr process
if encap entry is invalid.
Fixes: b11bde56246e ("net/mlx5e: TC, Offload rewrite and mirror to both internal and external dests")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250423083611.324567-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
